09.300BH.08 - EAO - Datasheet.Live

Product Specification

G1225x01 series

Crystal Clear Technology sdn. bhd.

16Jalan TP5—Taman Perindustrian Sime UEP

47600 Subang Jaya—Selangor DE

Malaysia. T: +603 80247099 F: +603 80247098

CRYSTAL CLEAR TECHNOLOGY SDN. BHD.

Spec. No: G1225x01xxx00 REV 2.0

1

1.0 Table of Contents

Page

1. Table of Contents 1

2. Record of revision 2

3. General specification 3

4. Absolute maximum ratings 4

5. Electrical characteristics 4

6. Environmental requirement 4

7. LCD specification 5 ~ 7

8. Interface 8

9. Functional Description 9 ~ 13

10. Instructions 14 ~ 15

11. Power supply 16

12. Quality assurance 17 ~ 24

13. Precautions in use LCM 25 ~ 26

14. Outline drawing 27

15. LCD Segment and Common Layout 28

CRYSTAL CLEAR TECHNOLOGY SDN. BHD.

Spec. No: G1225x01xxx00 REV 2.0

2

2.0 Record of revision

Rev Date Item Page Comment Originator Checked By

1.0

2.0

30/09/08

31/10/08

5.0

9.2.4

4

13

Initial Release

Vdd values update 3.0V typ and

3.3V max.

Figure error. Corrected from IF1,

IF2, IF3 tie to high (Vdd),

changed to all tie to low (Vss).

Syam

Azhar

CRYSTAL CLEAR TECHNOLOGY SDN. BHD.

Spec. No: G1225x01xxx00 REV 2.0

3

3.0 General specification

Display format: Graphics 255 (w) x 128 (h) dots

Dot size: 0.30 (w) x 0.30 (h) mm

Dot pitch: 0.32 (w) x 0.32 (h) mm

View area: 86.0 (w) x 44.0 (h) mm

Active area: 81.58 (w) x 40.94 (h) mm

General dimensions: 110.7 (w) x 63.2 (h) x 6.1 (t) mm

Controller/Driver: ST7529 or equivalent

Interface: Parallel/Serial

Driving method: 1/144 duty, 1/11 bias

Y : Yellow Green (STN)

G : Grey (STN)

B : Black & White (FSTN)

N : Negative (FSTN) Blue ( Single Retardation )

U : Negative (FSTN) Black/White ( Double Retardation )

S : Negative (STN) Purple

L : Negative (STN) Blue

Z : U : Negative (FSTN) Black/White ( Double Retardation ) TRI-AXIS

SERIES NUMBER FOR THIS STANDARD SPECIFICATION

STD. GRAPHIC : No. of rows followed by no. of column

SEMI - CUSTOMISE (MINOR CHANGES FROM STANDARD MODEL)

00 - STANDARD SPECIFICATION MODEL

T0 - WITH TOUCH PANEL

REFER TO FACTORY FOR OTHER VERSIONS. TERMS AND CONDITIONS APPLY

W : Wide Temperature ( -20°C to +70°C ), where storage temperature is (-30°C to +80°C)

N : Normal Temperature ( 0°C to +50°C ), where storage temperature is (-20°C to +70°C)

OPERATING TEMPERATURE

B : Bottom view ( 6 O'clock )

T : Top view ( 12 O'clock )

VIEWING ANGLE

1

G

MODULE VERSION

LCD MODE

W : Side Led Backlight (White)

N : No Backlight

BACKLIGHT MODE

MODEL NUMBER

00

5

2021

CRYSTAL CLEAR TECHNOLOGY SDN. BHD.

Spec. No: G1225x01xxx00 REV 2.0

4

4.0 Absolute maximum rating (at Vss = 0V, ambient temperature = 25°C)

NO ITEM SIMBOL MIN MAX UNIT

VDD -0.5 5.0 1. Operating Voltage Range

VDDA -0.5 5.0

V

2. Operating Temperature Top Refer page 3 °C

3. Storage Temperature Tst Refer page 3 °C

5.0 Electrical characteristics

NO ITEM SYMBOL CONDITION MIN TYP MAX UNIT

VDD 1. Operating Voltage

VDDA - - 3.0 3.3 V

2. Power Supply

voltage (VLCD) 25°C 16.0±5% V

3. Current Supply IDD V

DD = 3.3V - 3.2 - mA

5.1 Backlight Options

FORWARD VOLTAGE

(V)

FORWARD CURRENT

(mA)

NO COLOR

Min Typ. Max Min Typ. Max

MIN

BRIGHTNESS

(cd/m2) *

1. White - 4.0 - - 75 100 250

*Note : 1. Brightness measured at backlight surface.

2. On LCD surface, brightness is only about 10% to 15% of backlight brightness.

3. Lifetime of backlight: For YG, Amber, Red = 50K hrs. For White, Blue = 20K hrs

6.0 Environmental requirements

NO ITEM CONDITION

1. Operating

Temperature

Refer page 3

2. Storage Temperature Refer page 3

3. Operating Humidity 5% to 95%RH

4. Cycle Test 0 C @ 30 min to 50 C @ 30min for 1 cycle

run for 10 cycles

5. Lifetime 50000 HOURS (excluding backlight)

Note: The background on LCD has the possibility to be changed in different temperature range.

CRYSTAL CLEAR TECHNOLOGY SDN. BHD.

Spec. No: G1225x01xxx00 REV 2.0

5

7.0 LCD specification

7.1 Electro-optical characteristics (at ambient temperature = 25°C)

LCD TYPE

UNIT

NO ITEM SYMBOL CONDITION STN

YG

STN

GREY

STN

-VE

BLUE/

PURP

LE

FSTN

+VE

B/W

FSTN

–VE

BLUE

FSTN -

VE

TRUE

B/W

FSTN

-VE

TRI

AXIS

REF.

1

Operating

Voltage

(Volt)

VLCD θ = 0

Cr = max 16.0 ± 5% 7.1.1

θ x 1 +20 +15 +35 +20 +35 +30 +40

θ x 2 -20 -15 -35 -20 -35 -35 -40

θ y 1 -25 -20 -30 -25 -30 -30 -50

2

Viewing

Angle

(Deg)

θ y 2

CR ≥ 2

VLCD =

14.7V +25 +20 +30 +25 +30 +30 +30

7.1.2

3 Contrast

Ratio CR

θ = 00

VLCD

=14.7V

2.5 2.0 5.5 2.5 5.5 15 15 7.1.3

Rise

Time

(Tr)

θ = 00 400

4

Response

Time

(msec) Decay

Time

(Td)

θ = 00 400

7.1.4

Note:

1. Viewing angle data is based on bottom view product by default. Should it be a

top view product, values are then swap.

2. Contrast ratio is based on typical data when using white colour as backlight.

3. Equipment Used Eldim; Ez Contrast 120R , Spot Size = 2mm

CRYSTAL CLEAR TECHNOLOGY SDN. BHD.

Spec. No: G1225x01xxx00 REV 2.0

6

NO CHARACTERISTICS DEFINITIONS

7.1.1

Definition of Operating

Voltage (VLCD)

VLCD

1/F

VLCD : Operating Voltage

F : Frame Frequency

7.1.2

Definition of Viewing

Angle

TOP

θ REAR

LEFT RIGHT

FRONT

BOTTOM

REAR (θy2)

LEFT(θx2) RIGHT(θx1)

FRONT (θy1)

CRYSTAL CLEAR TECHNOLOGY SDN. BHD.

Spec. No: G1225x01xxx00 REV 2.0

7

7.1.3

Definition of Contrast

Ratio

NON-SELECT WAVE

BRIGHTNESS (%)

SELECT WAVE

b

a

OPERATION VOLTAGE

Contrast Ratio = Brightness of non-selected state (b)

Brightness of selected state (a)

Conditions

(a) Operating Voltage: VLCD

(b) Temperature: 25°C

(c) Viewing Angle, θ = 0o

7.1.4

Response Time

Luminance

(%)

90

10

Tr: Measured between 10% and 90% of LCD segment

maximum response with VON.

Td: With voltage switches to zero and the instant LCD

segment reaches 10% of its maximum response.

Td

Tr

Time

CRYSTAL CLEAR TECHNOLOGY SDN. BHD.

Spec. No: G1225x01xxx00 REV 2.0

8

8.0 Interface

8.1 Display Driver ST7529 OR EQUIVALENT

8.2 Pin No Symbol Description

1 V0 LCD driving voltage

2 V1 LCD driving voltage

3 V2 LCD driving voltage

4 V3 LCD driving voltage

5 V4 LCD driving voltage

6 VLCD LCD driving voltage

7 C6P Positive connection for capacitor 6

8 C4P Positive connection for capacitor 4

9 C2N Negative connection for capacitor 2

10 C2P Positive connection for capacitor 2

11 C1P Positive connection for capacitor 1

12 C1N Negative connection for capacitor 1

13 C3P Positive connection for capacitor 3

14 C5P Positive connection for capacitor 5

15 VDDA Internal generator supply

16 VSS Ground

17 VSS Ground

18 VDD Logic supply voltage

19 XCS Chip select input pin

20 SCL Serial clock input pin

21 SI Serial data input pin

22 IF3 Interface mode selection

23 IF2 Interface mode selection

24 IF1 Interface mode selection

25 RST Reset input active low

26 ERD R/W : 68000 Series Parallel Interface Read & Write

Control Input

RD : 8080 Series Parallel Interface Read Enable

Clock Input

27 D7 8 bit bi-directional data bus

28 D6 8 bit bi-directional data bus

29 D5 8 bit bi-directional data bus

30 D4 8 bit bi-directional data bus

31 D3 8 bit bi-directional data bus

32 D2 8 bit bi-directional data bus

33 D1 8 bit bi-directional data bus

34 D0 8 bit bi-directional data bus

35 EWR R/W : 68000 Series Parallel Interface Read & Write

Control Input

RD : 8080 Series Parallel Interface Write Enable

Clock Input

36 A0 Register select input pin

CRYSTAL CLEAR TECHNOLOGY SDN. BHD.

Spec. No: G1225x01xxx00 REV 2.0

9

9.0 Functional Descriptions

9.1 Read/Write timing characteristics

Read/Write characteristics (6800 series MPU)

CRYSTAL CLEAR TECHNOLOGY SDN. BHD.

Spec. No: G1225x01xxx00 REV 2.0

10

Read/Write characteristics (8080 series MPU)

CRYSTAL CLEAR TECHNOLOGY SDN. BHD.

Spec. No: G1225x01xxx00 REV 2.0

11

Read/Write characteristics (Serial Interface 4 Line)

CRYSTAL CLEAR TECHNOLOGY SDN. BHD.

Spec. No: G1225x01xxx00 REV 2.0

12

Read/Write characteristics (Serial Interface 3 Line)

9.2 Application Circuits

9.2.1 6800 – Series Parallel Interface

A0

EWR

ERD

D0~D7

VDD VDD

VSS

MCU LCD Module

A0

EWR

D0~D7

IF2

IF3

IF1

CRYSTAL CLEAR TECHNOLOGY SDN. BHD.

Spec. No: G1225x01xxx00 REV 2.0

13

9.2.2 8080 – Series Parallel Interface

A0

EWR

ERD

D0~D7

VDD VDD

VSS

MCU LCD Module

9.2.3 3 Lines Serial Interface

RST

SI

SCL

XCS

VSS

VDD

MCU LCD Module

9.2.4 4 Lines Serial Interface

RST

SI

SCL

XCS

A0

VSS

MCU LCD Module

A0

EWR

ERD

D0~D7

IF1

IF2

IF3

RST

SI

SCL

XCS

IF1

IF2

IF3

RST

SI

SCL

XCS

A0

IF1

IF2

IF3

CRYSTAL CLEAR TECHNOLOGY SDN. BHD.

Spec. No: G1225x01xxx00 REV 2.0

14

10. Instruction set

CRYSTAL CLEAR TECHNOLOGY SDN. BHD.

Spec. No: G1225x01xxx00 REV 2.0

15

CRYSTAL CLEAR TECHNOLOGY SDN. BHD.

Spec. No: G1225x01xxx00 REV 2.0

16

11. Power Supply

11.1 6x Boosting

11.2 7x Boosting

Cap = 1.0 uF to 2.2 uF

B ACKLIGHT SUPPLY

A

K

+4.0V

0V

CRYSTAL CLEAR TECHNOLOGY SDN. BHD.

Spec. No: G1225x01xxx00 REV 2.0

17

12.0 Quality Assurance

12.1 ZONE DEFINITION

12.2 REJECTION CRITERIA

12.2.1 DIMENSIONAL DEFECTS

Defect

Category

Defect

Description Criterion Drawing Specification

Glass Size Dimensions of

LCD, do not

conform to the

drawing

Reject Refer to LCD Physical

Dimension Drawing

Perimeter

Seal

Extension

Perimeter seal

epoxy enters the

effective

viewing area

Reject

End Seal

Size

Size of end seal

does not meet

drawing

specification

Reject Refer to LCD Physical

Dimension Drawing

12.2.2 VISUAL DEFECTS

Defect

Category

Defect

Description Criterion Drawing Specification

Fracture A type of

glass

breakage

containing

running

cracks.

Inspectors

should

attempt to

remove it

with

fingernail. If

removed,

evaluate as

chip

Reject – if the

size is > 30%

of the contact

ledge width.

EFFECTIVE VIEWING AREA

ZONE A

ZONE B

(Outside Viewing Area)

ZONE C

(Sealing Area)

CRYSTAL CLEAR TECHNOLOGY SDN. BHD.

Spec. No: G1225x01xxx00 REV 2.0

18

Defect

Category

Defect

Description Criterion Drawing Specification

Chip Chip in cross

over area

1) Reject - if

the chip

causes

crossover dot

to be exposed

2) Chip on

outside edge

of the glass

plate but is

greater than

50% of glass

thickness at

crossover dot

is reject able.

Chip Chip in

contact pad

area

Accept if:-

a) X ≤ 2.0mm

b) Y ≤ 0.5mm

c) Z disregard

Chip in non-

contact pad

area

Accept if:-

a) X ≤ 6.0mm

b) Y ≤ 1.0mm

c) Z disregard

Chip in

perimeter

seal area

Accept if:-

a) Y ≤ 1/3 of

perimeter seal

width (W)

b) X ≤ 3.0mm

c) Z disregard

d) X and Y not

touch

crossover dot

Corner Chip Corner chip

within seal

area

Accept if:-

a) X ≤ 1/3 of

perimeter seal

width (W)

b) Y ≤ 1/3 of

perimeter seal

width (W)

c) Z disregard

Chip

Epoxy of

crossover dot

exposed

Z

X

Y

W

Z

Y

X

Y

Z

Y

X

Y

Z

X

Y

X

Z

W

CRYSTAL CLEAR TECHNOLOGY SDN. BHD.

Spec. No: G1225x01xxx00 REV 2.0

19

Defect

Category

Defect

Description Criterion Drawing Specification

Corner chip

not effecting

contact pad /

ITO

Accept if:-

a) XY ≤ 4mm2

AND

b) Y ≤ D and

X ≤ 2.0mm

c) Z disregard

Corner chip

effecting

contact pad /

ITO

A) Accept if:-

a) XY ≤ 4mm2

AND

b) Y ≤ D and

X ≤ 2.0mm

B) Accept if:-

a) X1 ≤

2.0mm

b) Y1 ≤ 0.5mm

Z disregard

Glass flare A thin layer

of glass flare

at contact

area

Accept if:-

a) Flare

thickness ≤ ¼

W when W ≤

3mm

b) Flare

thickness ≤

1mm when W

> 3mm

W: Contact

ledge width

Glass burr A rough

edge(s) left

along the

scribing edge

(i.e. along

the edges of

display)

Reject – if the

burr cause

undersize or

oversize of the

LCD

Refer to LCD Physical Dimension

Drawing

Rainbow Colored ring

in sharp

blotches

observed

Reject – if 3 or

more colored

rings in sharp

blotches of

color are

observed.

(Limit samples

should be used

when

applicable)

Y

X

D

Z

D

X

X1

Y Y1

A

B

Z

CRYSTAL CLEAR TECHNOLOGY SDN. BHD.

Spec. No: G1225x01xxx00 REV 2.0

20

Defect

Category

Defect

Description Criterion Drawing Specification

Discoloration Reject - if the

discolorations

enter the

active viewing

area of LCD.

Color of the

LCD shall

follow product

specification

as specified in

the

manufacturing

specification

Air Void LC does not

fulfill the

display

Reject

Fill end

contamination

Discoloration

at end seal

area

Reject if

discoloration

exceeded the

baffle (for

display with

baffle) or

viewing area

(for display

without baffle)

12.2.3 POLARIZER DEFECTS

Defect

Category Defect Description Criterion Drawing Specification

Polarizer

defect

Polarizer coverage 1- Polarizer should cover effective

viewing area of display.

2- It is acceptable if perimeter seal bolder

at all sides could be seen.

3- It is acceptable if polarizer attaching

position meeting the tolerance

mentioned in the drawing.

4- It is reject able if polarizer edge jagged

and not even

Refer to LCD Physical

Dimension Drawing

Polarizer Peeling /

delamination

1- Reject if any edge or corner of the

polarizer is lifted up or not adheres to

the glass

Polarizer Scratches 1- Any scratch should be acceptable if it is

not visible from viewing distance at head

of position

2-Polarizer scratch in viewing area is

reject able if it is visible from the

specified viewing distance

3-Defect, which is visible under surface

glare, should be disregard

CRYSTAL CLEAR TECHNOLOGY SDN. BHD.

Spec. No: G1225x01xxx00 REV 2.0

21

Defect

Category Defect Description Criterion Drawing Specification

Polarizer damage 1-Stain mark or depression in front

polarizer surface should be acceptable if it

is not visible from viewing distance at

head on position.

2-Defect, which is visible under surface

glare, should be disregard

Zone / Acceptable No.

Dimension A B C

D ≤ 0.30mm NC NC

D ≤ 0.50mm 2 NC

0.50 < D ≤

0.60mm 1 2

D > 0.60mm 0 0

NC if

the

Polarize

r not

lifted

up/ peel

off

NC: No count

D: Mean Diameter of Defect

3 are the totally permissible numbers of

bubble

Polarizer bubble /

Foreign material

12.2.4 ELECTRICAL TEST DEFECTS

Defect

Category Defect Description Criterion Drawing Specification

Missing

common

Part of the pattern

does not light up

Reject

Missing

segment

One or few

segment does not

light up

Reject

Common-

common short

Common and

common connected

Reject

Segment-

segment short

Segment and

segment connected

Reject

Common –

segment short

Common and

segment connected

Reject

Wrong

viewing angle

Wrong viewing

angle

Reject if display viewing angle not

conform to customer requirement

Metal residue Extra spot lights up

at the border of the

segment.

Accept if ≤ 0.20mm (mean diameter)

Slow

response

Response of the

display on one side

slower than the

other side

Reject if it is visible at 30cm distance

A

B

D = (A + B)/2

CRYSTAL CLEAR TECHNOLOGY SDN. BHD.

Spec. No: G1225x01xxx00 REV 2.0

22

Defect

Category Defect Description Criterion Drawing Specification

Zone /

Dimension Acceptable No.

- 1 per pixel/dot

Located inside

single pixel/dot:-

(X + Y)/2 ≤

0.20mm

- 3 per display

(Active Area)

- 1 per pixel/dot Laid over the plural

pixel/dots:

(X + Y)/2 ≤

0.20mm

- 3 per display

(Active Area)

Pin Hole Pin hole / void at

light up segment

(¾ or larger part of dot area has to be

effective for display)

Lacked

deformation

Accept if:

i) X ≤ 0.15 and

ii) Y ≤ 0.15

Deformed

display dot

Added deformation

Accept if:

i) X < 0.02 and

ii) Y < 0.02

Reverse twist/

tilt

Segment are darker

or clearer than

other area of the

same segment

Reject

Misalignment Segment fatter or

smaller or extra

segment

Reject if > 10% of designed segment

width and visible at 30cm distance

Segment

Smearing

Light up segment

smear

Reject

Dim segment Display shows

poor contrast at pre

set voltage

Reject

Y

X

Y

X

Y

CRYSTAL CLEAR TECHNOLOGY SDN. BHD.

Spec. No: G1225x01xxx00 REV 2.0

23

12.2.5 BLACK SPOT, WHITE SPOT AND FOREIGN MATERIAL (SOLID FIGURE)

Defect

Category Defect Description Criterion Drawing Specification

Zone / Acceptable No.

Dimension A B C

D < 0.10mm NC NC NC

0.10<D < 0.15mm 3 3 NC

0.15 < D < 0.25mm 1 2 NC

0.25 < D < 0.35mm 1 1 NC

D > 0.35 mm 0 0 NC

NC: No count

Black Spot,

White Spot

and Foreign

Material

Black Spot, White

Spot and Foreign

Material

D: Mean Diameter of Defect

NOTE: The 1/3 or larger parts of individual dot has to be lighted on.

The solid figure is that the defect has clear-cut outline at the optimum driving condition in both positive

and negative, of which size does not change when the contrast changes.

12.2.6 BLACK SPOT, WHITE SPOT AND FOREIGN MATERIAL (FADED FIGURE)

Defect

Category Defect Description Criterion Drawing Specification

Zone / Acceptable No.

Dimension A B C

D < 0.60mm NC NC NC

0.60<D < 0.70mm 3 NC

0.70 < D < 0.80mm 1 NC

D > 0.80 mm 0 NC

NC: No count

Black Spot,

White Spot

and Foreign

Material

Black Spot, White

Spot and Foreign

Material

D: Mean Diameter of Defect

NOTE: Faded figure means that the defects has unclear outline at the optimum driving condition in both

positive and negative, of which size seems to change when the contrast changes.

A

B

D = (A + B)/2

A

B

D = (A + B)/2

CRYSTAL CLEAR TECHNOLOGY SDN. BHD.

Spec. No: G1225x01xxx00 REV 2.0

24

12.2.7 LINE SHAPE AND SCRATCHES

Defect

Category Defect Description Criterion Drawing Specification

Zone /Dimension Acceptable No.

X Y A B C

NC ≤

0.03mm

NC NC NC

≤ 2

mm

≤

0.05mm

1 1 NC

≤ 1

mm

≤

0.10mm

1 2 NC

NC ≥

0.10mm

Due to (1) round

defect

Line shape

and scratches

Line shape and

scratches

NOTE: Length is X and Width is Y.

REMARK:

i) Total amount of spot defects including round and linear – A total of 5 permissible numbers of defects

in Zone A & B including above (12.2.5), (12.2.6), (12.2.7). Regardless of number of defects, the

minimum distance between individual defects have to be 5mm or larger.

ii) All the other items of inspection that are not included herein must be determined by the “Limit

Standard” sample, which were occasionally set up with the mutual consent of both parties. In every

case of the items set up with the Limit Standard, the Limit Standard always takes precedence over the

other means of definition.

CRYSTAL CLEAR TECHNOLOGY SDN. BHD.

Spec. No: G1225x01xxx00 REV 2.0

25

13. Precaution for using LCM

1. Liquid Crystal Display (LCD)

LCD is made up of glass, organic sealant, organic fluid and

polymer based polarizers. The following precautions should

be taken when handling.

b) Keep the temperature within the range of use and

storage. Excessive temperature and humidity

could cause polarization degredation, polarizer

peel off or bubble.

c) Do not contact the exposed polarizer with

anything harder than HB pencil lead. To clean

dust off the display surface, wipe gently with

cotton, chamois or other soft material soaked in

petroleum benzin.

d) Wipe off saliva or water drops immediately.

Contact with water over a long period of time

may cause polarizer deformation or colour

fading, while an active LCD with water

condensation on its surface will cause corrosion

of ITO electrodes.

e) Glass can be easily chipped or cracked from

rough handling, especially at corners and edges.

f) Do not drive LCD with DC voltage.

2. Liquid Crystal Display Modules.

2.1 Mechanical Considerations

LCM are assembled and adjusted with a high

degree of precision. Avoid excessive shocks and

do not make any alterations or modification. The

following should be noted.

a) Do not tamper in any way with the tabs

on the metal frame.

b) Do not modify the PCB by drilling

extra holes, changing its outline,

moving its component or modifying its

pattern.

c) Do not touch the elastomer connector,

especially insert a backlight panel (for

example, EL)

d) When mounting a LCM make sure that

the PCB is not under any stress such as

bending or twisting. Elastomer contacts

are very delicate and missing pixels

could result from slight dislocation of

any of the elements.

a) Avoid pressing on the metal bezel,

otherwise the elastomer connector

could be deformed and lose contact,

resulting in missing pixels.

2.2 Static Electricity

LCM contains CMOS LSI’s and the same

precaution for such devices should apply, namely

a) The operator should be grounded whenever

he/she comes into contact with the module.

Never touch any of the conductive parts

such as the LSI pads, the copper leads on the

PCB and the interface terminals with any

parts of the human body.

b) The modules should be kept in antistatic

bags or other containers to static for storage.

c) Only properly grounded soldering irons

should be used.

d) If an electric screwdriver is used, it should

be well grounded and shielded from

commutator spark.

e) The normal static prevention measures

should be observed for work clothes and

working benches, the latter conductive

(rubber) mat is recommended.

f) Since dry air is inductive to statics, a relative

humidity of 50-60% is recommended.

2.3 Soldering

a) Solder only to the I/O terminals.

b) Use only soldering irons with proper

grounding and no leakage.

c) Soldering temperature: 280 °C

d) Soldering time: 3 to 4 sec

e) Use eutectic solder with resin flux fill.

f) If flux is used, the LCD surface should be

covered to avoid flux spatters. Flux residue

should be removed afterwards.

CRYSTAL CLEAR TECHNOLOGY SDN. BHD.

Spec. No: G1225x01xxx00 REV 2.0

26

2.4 Operation

a) The contras can be adjusted by varying the

LCD driving voltage V0

b) Driving voltage should be kept within

specified range, excess voltage shortens

display life.

c) Response time increases with decrease in

temperature.

d) Display may turn black or dark blue at

temperature above its operational range, this

is (however not pressing on the viewing

area) may cause the segments to appear

“fractured”.

e) Mechanical disturbance during operation (

such as pressing on the viewing area) may

cause the segments to appear “fractured”.

2.5 Storage

If any fluid leaks out of the damage glass cell,

wash off any human part that comes into contact

with soap and water. Never swallow the fluid.

The toxicity is extremely low but caution should

be exercised at all the time.

2.6 Limited Warranty

Unless otherwise agreed between Crystal Clear

Technology and customer, Crystal Clear

Technology will replace or repair any of its LCD

and LCM which is found to be defective

electrically and visually when inspected in

accordance with Crystal Clear Technology

acceptance standards, for a period of one year

from date of shipment. Confirmation of such date

shall be based on freight documents. The

warranty liability of Crystal Clear Technology is

limited to repair and/or replacement on the terms

set forth above. Crystal Clear Technology will

not responsible for any subsequent or

consequential events.

CRYSTAL CLEAR TECHNOLOGY SDN. BHD.

Spec. No: G1225x01xxx00 REV 2.0

27

16, JLN TP5, TMN PERINDUSTRIAN SIME UEP,

47500 SUBANG JAYA, SELANGOR DARUL EHSAN.

Crystal-Clea r Technology

01 36

CRYSTAL CLEAR TECHNOLOGY SDN. BHD.

Spec. No: G1225x01xxx00 REV 2.0

28

LCD Segment and Common Layout

Crystal Clear Technology

16 Jalan TP5—Taman Perindustrian Sime UEP

47600 Subang Jaya—Selangor DE

Malaysia