Features * High-density, High-performance, Electrically-erasable Complex * * * * * * * * * * * Programmable Logic Device - 128 Macrocells - 5 Product Terms per Macrocell, Expandable up to 40 per Macrocell - 84, 100, 160 Pins - 7.5 ns Maximum Pin-to-pin Delay - Registered Operation up to 125 MHz - Enhanced Routing Resources Flexible Logic Macrocell - D/T/Latch Configured Flip-flops - Global and Individual Register Control Signals - Global and Individual Output Enable - Programmable Output Slew Rate - Programmable Output Open Collector Option - Maximum Logic Utilization by Burying a Register within a COM Output Advanced Power Management Features - Automatic 10 A Standby for "L" Version - Pin-controlled 1 mA Standby Mode - Programmable Pin-keeper Inputs and I/Os - Reduced-power Feature per Macrocell Available in Commercial and Industrial Temperature Ranges Available in 84-lead PLCC, 100-lead PQFP, 100-lead TQFP and 160-lead PQFP Packages Advanced EE Technology - 100% Tested - Completely Reprogrammable - 10,000 Program/Erase Cycles - 20-year Data Retention - 2000V ESD Protection - 200 mA Latch-up Immunity JTAG Boundary-scan Testing to IEEE Std. 1149.1-1990 and 1149.1a-1993 Supported Fast In-System Programmability (ISP) via JTAG PCI-compliant 3.3 or 5.0V I/O Pins Security Fuse Feature Green (Pb/Halide-free/RoHS Compliant) Package Options Highperformance EE PLD ATF1508AS ATF1508ASL Enhanced Features * * * * * * * * * * * Improved Connectivity (Additional Feedback Routing, Alternate Input Routing) Output Enable Product Terms Transparent-latch Mode Combinatorial Output with Registered Feedback within Any Macrocell Three Global Clock Pins ITD (Input Transition Detection) Circuits on Global Clocks, Inputs and I/O Fast Registered Input from Product Term Programmable "Pin-keeper" Option VCC Power-up Reset Option Pull-up Option on JTAG Pins TMS and TDI Advanced Power Management Features - Edge-controlled Power-down "L" - Individual Macrocell Power Option - Disable ITD on Global Clocks, Inputs and I/O for "Z" Parts Rev. 0784P-PLD-7/05 1 100-lead PQFP Top View 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 I/O I/O I/O/PD1 I/O VCCIO I/O/TDI I/O I/O I/O I/O I/O I/O GND I/O I/O I/O I/O/TMS I/O I/O VCCIO I/O I/O I/O I/O I/O I/O I/O GND I/O I/O I/O I/O GND I/O/TDO I/O I/O I/O I/O VCCIO I/O I/O I/O I/O/TCK I/O I/O GND I/O I/O I/O I/O I/O 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 I/O I/O I/O I/O GND I/O/TDO I/O I/O I/O I/O I/O I/O VCCIO I/O I/O I/O I/O/TCK I/O I/O GND I/O I/O I/O I/O I/O I/O I/O VCCIO I/O I/O I/O I/O I/O I/O I/O VCCIO I/O I/O I/O GND VCCINT I/O I/O/PD2 I/O GND I/O I/O I/O I/O I/O 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 I/O I/O I/O I/O I/O VCCIO I/O I/O I/O GND VCCINT I/O I/O/PD2 I/O GND I/O I/O I/O I/O I/O VCCIO I/O/PD1 VCCIO I/O/TDI I/O I/O I/O I/O GND I/O I/O I/O I/O/TMS I/O I/O VCCIO I/O I/O I/O I/O I/O GND 11 10 9 8 7 6 5 4 3 2 1 84 83 82 81 80 79 78 77 76 75 I/O I/O I/O I/O GND I/O I/O I/O VCCINT INPUT/OE2/GCLK2 INPUT/GCLR INPUT/OE1 INPUT/GCLK1 GND I/O/GCLK3 I/O I/O VCCIO I/O I/O I/O I/O I/O I/O GND I/O I/O I/O VCCINT INPUT/OE2/GCLK2 INPUT/GCLR INPUT/OE1 INPUT/GCLK1 GND I/O/GCLK3 I/O I/O VCCIO I/O I/O I/O 84-lead PLCC Top View 160-lead PQFP Top View GND I/O I/O I/O I/O I/O I/O I/O VCCIO I/O I/O I/O GND VCCINT I/O I/O/PD2 I/O GND I/O I/O I/O I/O I/O I/O I/O 2 I/O GND I/O/TDO I/O I/O I/O I/O I/O I/O VCCIO I/O I/O I/O I/O/TCK I/O I/O GND I/O I/O I/O I/O I/O I/O I/O VCCIO 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 N/C N/C N/C N/C N/C N/C N/C GND I/O/TDO I/O I/O I/O I/O I/O I/O I/O VCCIO I/O I/O I/O I/O I/O/TCK I/O I/O I/O GND I/O I/O I/O I/O I/O I/O I/O N/C N/C N/C N/C N/C N/C N/C 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 I/O/PD1 I/O VCCIO I/O/TDI I/O I/O I/O I/O I/O I/O GND I/O I/O I/O I/O/TMS I/O I/O VCCIO I/O I/O I/O I/O I/O I/O I/O N/C N/C N/C N/C N/C N/C N/C VCCIO I/O/TDI I/O I/O I/O I/O I/O I/O I/O GND I/O I/O I/O I/O I/O/TMS I/O I/O I/O VCCIO I/O I/O I/O I/O I/O I/O I/O N/C N/C N/C N/C N/C N/C N/C I/O GND I/O N/C N/C N/C N/C I/O I/O I/O I/O I/O I/O I/O VCCIO I/O I/O I/O I/O GND VCCINT I/O I/O/PD1 I/O I/O GND I/O I/O I/O I/O I/O I/O I/O N/C N/C N/C N/C I/O VCCIO I/O 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 160 159 158 157 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 I/O I/O I/O I/O I/O GND I/O I/O I/O VCCINT INPUT/OE2/GCLK2 INPUT/GCLR INPUT/OE1 INPUT/GCLK1 GND I/O/GCLK3 I/O I/O VCCIO I/O I/O I/O I/O I/O I/O I/O I/O/PD2 I/O N/C N/C N/C N/C I/O I/O I/O I/O I/O GND I/O I/O I/O I/O VCCINT INPUT/OE2/GCLK2 INPUT/GCLR INPUT/OE1 INPUT/GCLK1 GND I/O/GCLK3 I/O I/O I/O VCCIO I/O I/O I/O I/O I/O N/C N/C N/C N/C I/O I/O I/O 100-lead TQFP Top View ATF1508AS(L) 0784P-PLD-7/05 ATF1508AS(L) Block Diagram 8 to 12 16 3 0784P-PLD-7/05 Description The ATF1508AS is a high-performance, high-density complex programmable logic device (CPLD) that utilizes Atmel's proven electrically-erasable technology. With 128 logic macrocells and up to 100 inputs, it easily integrates logic from several TTL, SSI, MSI, LSI and classic PLDs. The ATF1508AS's enhanced routing switch matrices increase usable gate count and increase odds of successful pin-locked design modifications. The ATF1508AS has up to 96 bi-directional I/O pins and four dedicated input pins, depending on the type of device package selected. Each dedicated pin can also serve as a global control signal, register clock, register reset or output enable. Each of these control signals can be selected for use individually within each macrocell. Each of the 128 macrocells generates a buried feedback that goes to the global bus. Each input and I/O pin also feeds into the global bus. The switch matrix in each logic block then selects 40 individual signals from the global bus. Each macrocell also generates a foldback logic term that goes to a regional bus. Cascade logic between macrocells in the ATF1508AS allows fast, efficient generation of complex logic functions. The ATF1508AS contains eight such logic chains, each capable of creating sum term logic with a fan-in of up to 40 product terms. The ATF1508AS macrocell, shown in Figure 1, is flexible enough to support highly-complex logic functions operating at high speed. The macrocell consists of five sections: product terms and product term select multiplexer; OR/XOR/CASCADE logic, a flip-flop, output select and enable, and logic array inputs. Unused macrocells are automatically disabled by the compiler to decrease power consumption. A security fuse, when programmed, protects the contents of the ATF1508AS. Two bytes (16 bits) of User Signature are accessible to the user for purposes such as storing project name, part number, revision or date. The User Signature is accessible regardless of the state of the security fuse. The ATF1508AS device is an in-system programmable (ISP) device. It uses the industry-standard 4-pin JTAG interface (IEEE Std. 1149.1), and is fully compliant with JTAG's Boundaryscan Description Language (BSDL). ISP allows the device to be programmed without removing it from the printed circuit board. In addition to simplifying the manufacturing flow, ISP also allows design modifications to be made in the field via software. Product Terms and Select Mux Each ATF1508AS macrocell has five product terms. Each product term receives as its inputs all signals from both the global bus and regional bus. The product term select multiplexer (PTMUX) allocates the five product terms as needed to the macrocell logic gates and control signals. The PTMUX programming is determined by the design compiler, which selects the optimum macrocell configuration. OR/XOR/ CASCADE Logic The ATF1508AS's logic structure is designed to efficiently support all types of logic. Within a single macrocell, all the product terms can be routed to the OR gate, creating a 5-input AND/OR sum term. With the addition of the CASIN from neighboring macrocells, this can be expanded to as many as 40 product terms with a little small additional delay. The macrocell's XOR gate allows efficient implementation of compare and arithmetic functions. One input to the XOR comes from the OR sum term. The other XOR input can be a product term or a fixed high- or low-level. For combinatorial outputs, the fixed level input allows polarity selection. For registered functions, the fixed levels allow DeMorgan minimization of product terms. The XOR gate is also used to emulate T- and JK-type flip-flops. 4 ATF1508AS(L) 0784P-PLD-7/05 ATF1508AS(L) Flip-flop The ATF1508AS's flip-flop has very flexible data and control functions. The data input can come from either the XOR gate, from a separate product term or directly from the I/O pin. Selecting the separate product term allows creation of a buried registered feedback within a combinatorial output macrocell. (This feature is automatically implemented by the fitter software). In addition to D, T, JK and SR operation, the flip-flop can also be configured as a flowthrough latch. In this mode, data passes through when the clock is high and is latched when the clock is low. The clock itself can be either the Global CLK Signal (GCK) or an individual product term. The flip-flop changes state on the clock's rising edge. When the GCK signal is used as the clock, one of the macrocell product terms can be selected as a clock enable. When the clock enable function is active and the enable signal (product term) is low, all clock edges are ignored. The flip-flop's asynchronous reset signal (AR) can be either the Global Clear (GCLEAR), a product term, or always off. AR can also be a logic OR of GCLEAR with a product term. The asynchronous preset (AP) can be a product term or always off. Extra Feedback The ATF15xxSE Family macrocell output can be selected as registered or combinatorial. The extra buried feedback signal can be either combinatorial or a registered signal regardless of whether the output is combinatorial or registered. (This enhancement function is automatically implemented by the fitter software.) Feedback of a buried combinatorial output allows the creation of a second latch within a macrocell. I/O Control The output enable multiplexer (MOE) controls the output enable signal. Each I/O can be individually configured as an input, output or for bi-directional operation. The output enable for each macrocell can be selected from the true or compliment of the two output enable pins, a subset of the I/O pins, or a subset of the I/O macrocells. This selection is automatically done by the fitter software when the I/O is configured as an input, all macrocell resources are still available, including the buried feedback, expander and cascade logic. Global Bus/Switch Matrix The global bus contains all input and I/O pin signals as well as the buried feedback signal from all 128 macrocells. The switch matrix in each logic block receives as its inputs all signals from the global bus. Under software control, up to 40 of these signals can be selected as inputs to the logic block. Foldback Bus Each macrocell also generates a foldback product term. This signal goes to the regional bus and is available to 16 macrocells. The foldback is an inverse polarity of one of the macrocell's product terms. The 16 foldback terms in each region allows generation of high fan-in sum terms (up to 21 product terms) with a little additional delay. 3.3V or 5.0V I/O Operation The ATF1508AS device has two sets of VCC pins viz, VCCINT and VCCIO. VCCINT pins must always be connected to a 5.0V power supply. VCCINT pins are for input buffers and are "compatible" with both 3.3V and 5.0V inputs. V CCIO pins are for I/O output drives and can be connected for 3.3/5.0V power supply. Open-collector Output Option This option enables the device output to provide control signals such as an interrupt that can be asserted by any of the several devices. 5 0784P-PLD-7/05 Figure 1. ATF1508AS Macrocell Programmable Pin-keeper Option for Inputs and I/Os The ATF1508AS offers the option of programming all input and I/O pins so that "pin-keeper" circuits can be utilized. When any pin is driven high or low and then subsequently left floating, it will stay at that previous high- or low-level. This circuitry prevents unused input and I/O lines from floating to intermediate voltage levels, which causes unnecessary power consumption and system noise. The keeper circuits eliminate the need for external pull-up resistors and eliminate their DC power consumption. Input Diagram 6 ATF1508AS(L) 0784P-PLD-7/05 ATF1508AS(L) Speed/Power Management The ATF1508AS has several built-in speed and power management features. The ATF1508AS contains circuitry that automatically puts the device into a low-power stand-by mode when no logic transitions are occurring. This not only reduces power consumption during inactive periods, but also provides proportional power-savings for most applications running at system speeds below 5 MHz. To further reduce power, each ATF1508AS macrocell has a Reduced-power bit feature. This feature allows individual macrocells to be configured for maximum power savings. This feature may be selected as a design option. I/O Diagram All ATF1508 also have an optional power-down mode. In this mode, current drops to below 10 mA. When the power-down option is selected, either PD1 or PD2 pins (or both) can be used to power down the part. The power-down option is selected in the design source file. When enabled, the device goes into power-down when either PD1 or PD2 is high. In the power-down mode, all internal logic signals are latched and held, as are any enabled outputs. All pin transitions are ignored until the PD pin is brought low. When the power-down feature is enabled, the PD1 or PD2 pin cannot be used as a logic input or output. However, the pin's macrocell may still be used to generate buried foldback and cascade logic signals. All power-down AC characteristic parameters are computed from external input or I/O pins, with Reduced-power Bit turned on. For macrocells in reduced-power mode (Reduced-power bit turned on), the reduced-power adder, tRPA, must be added to the AC parameters, which include the data paths tLAD, tLAC, tIC, tACL, tACH and tSEXP. Each output also has individual slew rate control. This may be used to reduce system noise by slowing down outputs that do not need to operate at maximum speed. Outputs default to slow switching, and may be specified as fast switching in the design file. 7 0784P-PLD-7/05 Design Software Support ATF1508AS designs are supported by several third-party tools. Automated fitters allow logic synthesis using a variety of high level description languages and formats. Power-up Reset The ATF1508AS is designed with a power-up reset, a feature critical for state machine initialization. At a point delayed slightly from VCC crossing VRST, all registers will be initialized, and the state of each output will depend on the polarity of its buffer. However, due to the asynchronous nature of reset and uncertainty of how VCC actually rises in the system, the following conditions are required: 1. The VCC rise must be monotonic, 2. After reset occurs, all input and feedback setup times must be met before driving the clock pin high, and, 3. The clock must remain stable during TD. The ATF1508AS has two options for the hysteresis about the reset level, VRST, Small and Large. During the fitting process users may configure the device with the Power-up Reset hysteresis set to Large or Small. Atmel POF2JED users may select the Large option by including the flag "-power_reset" on the command line after "filename.POF". To allow the registers to be properly reinitialized with the Large hysteresis option selected, the following condition is added: 4. If VCC falls below 2.0V, it must shut off completely before the device is turned on again. When the Large hysteresis option is active, ICC is reduced by several hundred microamps as well. Security Fuse Usage A single fuse is provided to prevent unauthorized copying of the ATF1508AS fuse patterns. Once programmed, fuse verify is inhibited. However, User Signature and device ID remains accessible. Programming ATF1508AS devices are in-system programmable (ISP) devices utilizing the 4-pin JTAG protocol. This capability eliminates package handling normally required for programming and facilitates rapid design iterations and field changes. Atmel provides ISP hardware and software to allow programming of the ATF1508AS via the PC. ISP is performed by using either a download cable or a comparable board tester or a simple microprocessor interface. To allow ISP programming support by the Automated Test Equipment (ATE) vendors, Serial Vector Format (SVF) files can be created by the Atmel ISP Software. Conversion to other ATE tester format beside SVF is also possible ATF1508AS devices can also be programmed using standard third-party programmers. With third-party programmer, the JTAG ISP port can be disabled thereby allowing four additional I/O pins to be used for logic. Contact your local Atmel representatives or Atmel PLD applications for details. 8 ATF1508AS(L) 0784P-PLD-7/05 ATF1508AS(L) ISP Programming Protection The ATF1508AS has a special feature that locks the device and prevents the inputs and I/O from driving if the programming process is interrupted for any reason. The inputs and I/O default to high-Z state during such a condition. In addition the pin-keeper option preserves the former state during device programming. All ATF1508AS devices are initially shipped in the erased state thereby making them ready to use for ISP. Note: JTAG-BST Overview For more information refer to the "Designing for In-System Programmability with Atmel CPLDs" application note. The JTAG boundary-scan testing is controlled by the Test Access Port (TAP) controller in the ATF1508AS. The boundary-scan technique involves the inclusion of a shift-register stage (contained in a boundary-scan cell) adjacent to each component so that signals at component boundaries can be controlled and observed using scan testing principles. Each input pin and I/O pin has its own boundary-scan cell (BSC) in order to support boundary-scan testing. The ATF1508AS does not currently include a Test Reset (TRST) input pin because the TAP controller is automatically reset at power-up. The six JTAG BST modes supported include: SAMPLE/PRELOAD, EXTEST, BYPASS and IDCODE. BST on the ATF1508AS is implemented using the Boundary-scan Definition Language (BSDL) described in the JTAG specification (IEEE Standard 1149.1). Any third-party tool that supports the BSDL format can be used to perform BST on the ATF1508AS. The ATF1508AS also has the option of using four JTAG-standard I/O pins for In-System programming (ISP). The ATF1508AS is programmable through the four JTAG pins using programming compatible with the IEEE JTAG Standard 1149.1. Programming is performed by using 5V TTL-level programming signals from the JTAG ISP interface. The JTAG feature is a programmable option. If JTAG (BST or ISP) is not needed, then the four JTAG control pins are available as I/O pins. JTAG Boundary-scan Cell (BSC) Testing The ATF1508AS contains up to 96 I/O pins and four input pins, depending on the device type and package type selected. Each input pin and I/O pin has its own boundary-scan cell (BSC) in order to support boundary-scan testing as described in detail by IEEE Standard 1149.1. A typical BSC consists of three capture registers or scan registers and up to two update registers. There are two types of BSCs, one for input or I/O pin, and one for the macrocells. The BSCs in the device are chained together through the (BST) capture registers. Input to the capture register chain is fed in from the TDI pin while the output is directed to the TDO pin. Capture registers are used to capture active device data signals, to shift data in and out of the device and to load data into the update registers. Control signals are generated internally by the JTAG TAP controller. The BSC configuration for the input and I/O pins and macrocells are shown below. 9 0784P-PLD-7/05 BSC Configuration Pins and Macrocells (Except JTAG TAP Pins) Note: The ATF1508AS has a pull-up option on TMS and TDI pins. This feature is selected as a design option. BSC Configuration for Macrocell TDO OEJ 0 0 1 D Q D Q 1 OUTJ 0 0 Pin 1 D Q D Q Capture DR Update DR 1 Mode TDI Shift Clock Macrocell BSC Boundary Scan Definition Language (BSDL) Models for the ATF1508 10 These are now available in all package types via the Atmel Web Site. These models can be used for Boundary-scan Test Operation in the ATF1508AS and have been scheduled to conform to the IEEE 1149.1 standard. ATF1508AS(L) 0784P-PLD-7/05 ATF1508AS(L) PCI Voltage-tocurrent Curves for +5V Signaling in Pull-up Mode The ATF1508AS also supports the growing need in the industry to support the new Peripheral Component Interconnect (PCI) interface standard in PCI-based designs and specifications. The PCI interface calls for high current drivers, which are much larger than the traditional TTL drivers. Pull Up VCC Test Point Voltage PCI Compliance 2.4 DC drive point 1.4 AC drive point -44 Current (mA) -178 -2 Pull Down VCC AC drive point Voltage PCI Voltage-tocurrent Curves for +5V Signaling in Pull-down Mode 2.2 DC drive point 0.55 Test Point 3,6 95 Current (mA) 380 11 0784P-PLD-7/05 PCI DC Characteristics Symbol Parameter Conditions Min Max Units VCC Supply Voltage 4.75 5.25 V VIH Input High Voltage 2.0 VCC + 0.5 V VIL Input Low Voltage -0.5 0.8 V VIN = 2.7V 70 A VIN = 0.5V -70 A Input High Leakage Current IIH (1) (1) IIL Input Low Leakage Current VOH Output High Voltage IOUT = -2 mA VOL Output Low Voltage IOUT = 3 mA, 6 mA CIN 2.4 V 0.55 V Input Pin Capacitance 10 pF CCLK CLK Pin Capacitance 12 pF CIDSEL IDSEL Pin Capacitance 8 pF Pin Inductance 20 nH LPIN Note: 1. Leakage current is without pin-keeper off. PCI AC Characteristics Symbol Parameter Conditions Min IOH(AC) Switching 0 < VOUT 1.4 -44 mA 1.4 < VOUT < 2.4 -44+(VOUT - 1.4)/0.024 mA Current High IOL(AC) Max Units 3.1 < VOUT < VCC Equation A(1) mA (Test High) VOUT = 3.1V -142 A Switching VOUT > 2.2V 95 2.2 > VOUT > 0 VOUT/0.023 Current Low mA mA (2) 0.1 > VOUT > 0 Equation B (Test Point) VOUT = 0.71 ICL Low Clamp Current -5 < VIN -1 -25+(VIN + 1)/0.015 SLEWR Output Rise Slew Rate 0.4V to 2.4V load 0.5 3.0 V/ns Output Fall Slew Rate 2.4V to 0.4V load 0.5 3.0 V/ns SLEWF Notes: 12 206 mA mA mA 1. Equation A: IOH = 11.9 (VOUT - 5.25) * (VOUT + 2.45) for VCC > VOUT > 3.1V. 2. Equation B: IOL = 78.5 * VOUT * (4.4 - VOUT) for 0V < VOUT < 0.71V. ATF1508AS(L) 0784P-PLD-7/05 ATF1508AS(L) Power-down Mode The ATF1508AS includes two pins for optional pin-controlled power-down feature. When this mode is enabled, the PD pin acts as the power-down pin. When the PD1 and PD2 pin is high, the device supply current is reduced to less than 10 mA. During power-down, all output data and internal logic states are latched and held. Therefore, all registered and combinatorial output data remain valid. Any outputs that were in a high-Z state at the onset will remain at highZ. During power-down, all input signals except the power-down pin are blocked. Input and I/O hold latches remain active to ensure that pins do not float to indeterminate levels, further reducing system power. The power-down pin feature is enabled in the logic design file. Designs using either power-down pin may not use the PD pin logic array input. However, buried logic resources in this macrocell may still be used. Power-down AC Characteristics(1)(2) -7 Symbol tIVDH Parameter Valid I, I/O before PD High (2) tGVDH Valid OE tCVDH Valid Clock(2) before PD High tDHIX I, I/O Don't Care after PD High (2) before PD High Min -10 Max Min -15 Max Min -20 Max Min -25 Max Min Max Units 7 10 15 20 25 ns 7 10 15 20 25 ns 7 10 15 20 25 ns 12 15 25 30 35 ns OE Don't Care after PD High 12 15 25 30 35 ns tDHCX Clock (2) 12 15 25 30 35 ns tDLIV PD Low to Valid I, I/O 1 1 1 1 1 s tDLGV PD Low to Valid OE (Pin or Term) 1 1 1 1 1 s tDLCV PD Low to Valid Clock (Pin or Term) 1 1 1 1 1 s tDLOV PD Low to Valid Output 1 1 1 1 1 s tDHGX Notes: Don't Care after PD High 1. For slow slew outputs, add tSSO. 2. Pin or product term. Absolute Maximum Ratings* Temperature Under Bias.................................. -40C to +85C *NOTICE: Storage Temperature ..................................... -65C to +150C Voltage on Any Pin with Respect to Ground .........................................-2.0V to +7.0V(1) Voltage on Input Pins with Respect to Ground During Programming.....................................-2.0V to +14.0V(1) Programming Voltage with Respect to Ground .......................................-2.0V to +14.0V(1) Note: Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 1. Minimum voltage is -0.6V DC, which may undershoot to -2.0V for pulses of less than 20 ns. Maximum output pin voltage is VCC + 0.75V DC, which may overshoot to 7.0V for pulses of less than 20 ns. 13 0784P-PLD-7/05 DC and AC Operating Conditions Commercial Industrial Operating Temperature (Ambient) 0C - 70C -40C - 85C VCCINT or VCCIO (5V) Power Supply 5V 5% 5V 10% 2.7V - 3.6V 2.7V - 3.6V VCCIO (3.3V) Power Supply DC Characteristics(1) Symbol Parameter Condition IIL Input or I/O Low Leakage Current IIH Input or I/O High Leakage Current IOZ Tri-state Output Off-state Current VO = VCC or GND ICC1 Power Supply Current, Standby VCC = Max VIN = 0, VCC VIN = VCC Std Mode "L" Mode ICC2 Power Supply Current, Power-down Mode VCC = Max VIN = 0, VCC "PD" Mode ICC3(2) Reduced-power Mode Supply Current VCC = Max VIN = 0, VCC Std Mode VCCIO Supply Voltage Min 5.0V Device Output Typ Max Units -2 -10 A 2 10 A 40 A -40 Com. 160 mA Ind. 180 mA Com. 10 A Ind. 10 1 Com. A 10 mA 65 Ind. mA 85 mA Com. 4.75 5.25 V Ind. 4.5 5.5 V 3.0 3.6 V VCCIO Supply Voltage VIL Input Low Voltage -0.3 0.8 V VIH Input High Voltage 2.0 VCCIO + 0.3 V VOL VOH Notes: 14 3.3V Device Output Output Low Voltage (TTL) VIN = VIH or VIL VCCIO = MIN, IOL = 12 mA Com. 0.45 V Ind. 0.45 V Output Low Voltage (CMOS) VIN = VIH or VIL VCC = MIN, IOL = 0.1 mA Com. 0.2 V Ind. 0.2 V Output High Voltage (TTL) VIN = VIH or VIL VCCIO = MIN, IOH = -4.0 mA 2.4 V 1. Not more than one output at a time should be shorted. Duration of short circuit test should not exceed 30 sec. 2. ICC3 refers to the current in the reduced-power mode when macrocell reduced-power is turned ON. ATF1508AS(L) 0784P-PLD-7/05 ATF1508AS(L) Pin Capacitance(1) Typ Max Units Conditions CIN 8 10 pF VIN = 0V; f = 1.0 MHz CI/O 8 10 pF VOUT = 0V; f = 1.0 MHz Note: 1. Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested. The OGI pin (high-voltage pin during programming) has a maximum capacitance of 12 pF. Timing Model U Input Test Waveforms and Measurement Levels rR, tF = 1.5 ns typical Output AC Test Loads (3.0V)* (703 )* (8060 )* Note: *Numbers in parenthesis refer to 3.0V operating conditions (preliminary). 15 0784P-PLD-7/05 SUPPLY CURRENT VS. FREQUENCY LOW-POWER ("L") VERSION (TA = 25C) SUPPLY CURRENT VS. SUPPLY VOLTAGE (TA = 25C, F = 0) 200.0 250.0 STANDARD POWER 150.0 STANDARD POWER ICC (mA) ICC (mA) 200.0 150.0 REDUCED POWER MODE 100.0 REDUCED POWER MODE 50.0 100.0 0.0 0.00 50.0 4.50 4.75 5.00 VCC (V) 5.25 5.50 5.00 10.00 FREQUENCY (MHz) 15.00 20.00 OUTPUT SOURCE CURRENT VS. SUPPLY VOLTAGE (VOH = 2.4V, TA = 25C) SUPPLY CURRENT VS. SUPPLY VOLTAGE LOW-POWER ("L") VERSION (TA = 25C, F = 0) 0 30.0 -10 IOH (mA) -20 ICC ( A) 20.0 -30 -40 10.0 -50 0.0 4.50 4.75 5.00 VCC (V) 5.25 -60 4.50 5.50 5.00 5.25 5.50 SUPPLY VOLTAGE (V) INPUT CLAMP CURRENT VS. INPUT VOLTAGE (VCC = 5V, TA = 25C) SUPPLY CURRENT VS. FREQUENCY STANDARD POWER (TA = 25C, F = 0) 0 -20 INPUT CURRENT (mA) 300.0 250.0 STANDARD POWER 200.0 ICC ( A) 4.75 150.0 100.0 REDUCED POWER MODE -40 -60 -80 -100 -120 -140 50.0 0.0 0.00 -160 20.00 40.00 60.00 FREQUENCY (MHz) 80.00 -1.4 100.00 -1.2 -1.0 -0.8 -0.6 -0.4 -0.2 0.0 INPUT VOLTAGE (V) OUTPUT SINK CURRENT VS. SUPPLY VOLTAGE (VOL = 0.5V, TA = 25C) SUPPLY CURRENT VS. SUPPLY VOLTAGE PIN-CONTROLLED POWER-DOWN MODE (TA = 25C, F = 0) 43 1100.0 42 41 IOL (mA) 1000.0 ICC ( A) STANDARD POWER 900.0 40 39 38 800.0 37 REDUCED POWER MODE 700.0 4.50 16 4.75 5.00 VCC (V) 5.25 5.50 36 4.50 4.75 5.00 5.25 5.50 SUPPLY VOLTAGE (V) ATF1508AS(L) 0784P-PLD-7/05 ATF1508AS(L) NORMALIZED TCO VS. SUPPLY VOLTAGE (TA = 25C) OUTPUT SOURCE CURRENT VS. SUPPLY VOLTAGE (VCC = 5V, TA = 25C) 1.20 -10 NORMALIZED TPD IOH (mA) -30 -50 -70 -90 -110 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 1.10 1.00 0.90 0.80 4.50 5.0 4.75 5.00 SUPPLY VOLTAGE (V) OUTPUT VOLTAGE (V) 5.50 NORMALIZED TSU VS. SUPPLY VOLTAGE (TA = 25C) INPUT CURRENT VS. INPUT VOLTAGE (VCC = 5V, TA = 25C) 1.20 40 5.25 1.10 20 NORMALIZED TSU INPUT CURRENT ( A) 30 10 0 -10 1.00 0.90 -20 -30 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 0.80 4.50 5.0 4.75 5.00 SUPPLY VOLTAGE (V) INPUT VOLTAGE (V) 5.25 5.50 NORMALIZED TPD VS. TEMPERATURE (VCC = 5.0V) OUTPUT SINK CURRENT VS. OUTPUT VOLTAGE (VCC = 5V, TA = 25C) 140 1.20 120 NORMALIZED TPD IOL (mA) 100 80 60 40 1.10 1.00 0.90 20 0 0.80 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 -40 0 1.20 1.20 1.10 NORMALIZED TCO NORMALIZED TPD 75 NORMALIZED TCO VS. TEMPERATURE (VCC = 5.0V) NORMALIZED TPD VS. SUPPLY VOLTAGE (TA = 25C) 1.00 0.90 0.80 4.50 25 TEMPERATURE (C) OUTPUT VOLTAGE (V) 1.10 1.00 0.90 0.80 4.75 5.00 SUPPLY VOLTAGE (V) 5.25 5.50 -40 0 25 75 TEMPERATURE (C) 17 0784P-PLD-7/05 NORMALIZED TSU VS. TEMPERATURE (VCC = 5.0V) NORMALIZED TSU 1.20 1.10 1.00 0.90 0.80 -40 0 25 75 TEMPERATURE (C) 18 ATF1508AS(L) 0784P-PLD-7/05 ATF1508AS(L) AC Characteristics (1) -7 Min -10 Max Min -15 -20 Max Min Max 7.5 10 3 15 7 9 3 12 Symbol Parameter tPD1 Input or Feedback to Non-registered Output tPD2 I/O Input or Feedback to Non-registered Feedback tSU Global Clock Setup Time 6 7 11 16 20 ns tH Global Clock Hold Time 0 0 0 0 0 ns tFSU Global Clock Setup Time of Fast Input 3 3 3 3 3 ns tFH Global Clock Hold Time of Fast Input 0.5 0.5 1.0 1.5 2 MHz tCOP Global Clock to Output Delay tCH Global Clock High Time 3 4 5 6 7 ns tCL Global Clock Low Time 3 4 5 6 7 ns tASU Array Clock Setup Time 3 3 4 4 5 ns tAH Array Clock Hold Time 2 3 4 5 6 ns tACOP Array Clock Output Delay tACH Array Clock High Time 3 4 6 8 10 ns tACL Array Clock Low Time 3 4 6 8 10 ns tCNT Minimum Clock Global Period fCNT Maximum Internal Global Clock Frequency tACNT Minimum Array Clock Period fACNT Maximum Internal Array Clock Frequency fMAX Maximum Clock Frequency tIN Input Pad and Buffer Delay 0.5 0.5 2 2 2 ns tIO I/O Input Pad and Buffer Delay 0.5 0.5 2 2 2 ns tFIN Fast Input Delay 1 1 2 2 2 ns tSEXP Foldback Term Delay 4 5 8 10 12 ns tPEXP Cascade Logic Delay 0.8 0.8 1 1 1.2 ns tLAD Logic Array Delay 3 5 6 7 8 ns tLAC Logic Control Delay 3 5 6 7 8 ns tIOE Internal Output Enable Delay 2 2 3 3 4 ns tOD1 Output Buffer and Pad Delay (Slow slew rate = OFF; VCCIO = 5V; CL = 35 pF) 2 1.5 4 5 6 ns 4.5 5 7.5 125 8 10 8 8 10 Min Max Units 20 25 ns 16 20 ns 13 20 13 76.9 Max 10 15 10 100 Min -25 25 17 66 13 22 50 17 ns ns ns MHz 22 ns 125 100 76.9 66 50 MHz 166.7 125 100 41.7 33.3 MHz 19 0784P-PLD-7/05 AC Characteristics (Continued)(1) -7 Symbol Parameter Min tOD2 Output Buffer and Pad Delay (Slow slew rate = OFF; VCCIO = 3.3V; CL = 35 pF) tOD3 Output Buffer and Pad Delay (Slow slew rate = ON; VCCIO = 5V or 3.3V; CL = 35 pF) tZX1 -10 Max Min -15 Max Min -20 Max Min -25 Max Min Max Units 2.5 2.0 5 6 7 ns 5 5.5 8 10 12 ns Output Buffer Enable Delay (Slow slew rate = OFF; VCCIO = 5.0V; CL = 35 pF) 4.0 5.0 7 9 10 ns tZX2 Output Buffer Enable Delay (Slow slew rate = OFF; VCCIO = 3.3V; CL = 35 pF) 4.5 5.5 7 9 10 ns tZX3 Output Buffer Enable Delay (Slow slew rate = ON; VCCIO = 5.0V/3.3V; CL = 35 pF) 9 9 10 11 12 ns tXZ Output Buffer Disable Delay (CL = 5 pF) 4 5 6 7 8 ns tSU Register Setup Time 3 2 4 5 6 ns tH Register Hold Time 2 3 4 5 6 ns tFSU Register Setup Time of Fast Input 3 3 2 2 3 ns tFH Register Hold Time of Fast Input 0.5 0.5 2 2 2.5 ns tRD Register Delay 1 2 1 2 2 ns tCOMB Combinatorial Delay 1 2 1 2 2 ns tIC Array Clock Delay 3 5 6 7 8 ns tEN Register Enable Time 3 5 6 7 8 ns tGLOB Global Control Delay 1 1 1 1 1 ns tPRE Register Preset Time 2 3 4 5 6 ns tCLR Register Clear Time 2 3 4 5 6 ns tUIM Switch Matrix Delay 1 1 2 2 2 ns 10 11 13 14 15 ns tRPA Notes: 20 Reduced-power Adder (2) 1. See ordering information for valid part numbers. 2. The tRPA parameter must be added to the tLAD, tLAC,tTIC, tACL, and tSEXP parameters for macrocells running in the reducedpower mode. ATF1508AS(L) 0784P-PLD-7/05 ATF1508AS(L) ATF1508AS Dedicated Pinouts Dedicated Pin 84-lead J-lead 100-lead PQFP 100-lead TQFP 160-lead PQFP INPUT/OE2/GCLK2 2 92 90 142 INPUT/GCLR 1 91 89 141 INPUT/OE1 84 90 88 140 INPUT/GCLK1 83 89 87 139 I/O /GCLK3 81 87 85 137 12,45 3,43 1,41 63,159 I/O / TDI(JTAG) 14 6 4 9 I/O / TMS(JTAG) 23 17 15 22 I/O / TCK(JTAG) 62 64 62 99 I/O / TDO(JTAG) 71 75 73 112 7,19,32,42, 47,59,72,82 13,28,40,45, 61,76,88,97 11,26,38,43, 59,74,86,95 17,42,60,66,95, 113,138,148 VCCINT 3,43 41,93 39,91 61,143 VCCIO 13,26,38, 53,66,78 5,20,36,53,68,84 3,18,34,51,66,82 8,26,55,79,104,133 N/C - - - 1,2,3,4,5,6,7,34,35,36, 37,38,39,40,44,45,46, 47,74,75,76,77,81,82, 83,84,85,86,87,114, 115,116,117,118,119, 120,124,125,126,127, 154,155,156,157 # of SIGNAL PINS 68 84 84 100 # USER I/O PINS 64 80 80 96 I/O / PD (1, 2) GND OE (1, 2) Global OE Pins GCLR Global Clear Pin GCLK (1, 2, 3) Global Clock Pins PD (1, 2) Power-down pins TDI, TMS, TCK, TDO JTAG pins used for boundary scan testing or in-system programming GND Ground Pins VCCINT VCC pins for the device (+5V - Internal) VCCIO VCC pins for output drivers (for I/O pins) (+5V or 3.3V - I/Os) 21 0784P-PLD-7/05 ATF1508AS I/O Pinouts MC PLB 84-lead J-lead 100-lead PQFP 100-lead TQFP 160-lead PQFP MC PLB 84-lead J-lead 100-lead PQFP 100-lead TQFP 160-lead PQFP 1 A - 4 2 160 33 C - 27 25 41 2 A - - - - 34 C - - - - 3 A/ PD1 12 3 1 159 35 C 31 26 24 33 4 A - - - 158 36 C - - - 32 5 A 11 2 100 153 37 C 30 25 23 31 6 A 10 1 99 152 38 C 29 24 22 30 7 A - - - - 39 C - - - - 8 A 9 100 98 151 40 C 28 23 21 29 9 A - 99 97 150 41 C - 22 20 28 10 A - - - - 42 C - - - - 11 A 8 98 96 149 43 C 27 21 19 27 12 A - - - 147 44 C - - - 25 13 A 6 96 94 146 45 C 25 19 17 24 14 A 5 95 93 145 46 C 24 18 16 23 15 A - - - - 47 C - - - - 16 A 4 94 92 144 48 C/ TMS 23 17 15 22 17 B 22 16 14 21 49 D 41 39 37 59 18 B - - - - 50 D - - - - 19 B 21 15 13 20 51 D 40 38 36 58 20 B - - - 19 52 D - - - 57 21 B 20 14 12 18 53 D 39 37 35 56 22 B - 12 10 16 54 D - 35 33 54 23 B - - - - 55 D - - - - 24 B 18 11 9 15 56 D 37 34 32 53 25 B 17 10 8 14 57 D 36 33 31 52 26 B - - - - 58 D - - - - 27 B 16 9 7 13 59 D 35 32 30 51 28 B - - - 12 60 D - - - 50 29 B 15 8 6 11 61 D 34 31 29 49 30 B - 7 5 10 62 D - 30 28 48 31 B - - - - 63 D - - - - 32 B/ TDI 14 6 4 9 64 D 33 29 27 43 65 E 44 42 40 62 97 G 63 65 63 100 22 ATF1508AS(L) 0784P-PLD-7/05 ATF1508AS(L) ATF1508AS I/O Pinouts (Continued) MC PLB 84-lead J-lead 100-lead PQFP 100-lead TQFP 160-lead PQFP MC PLB 84-lead J-lead 100-lead PQFP 100-lead TQFP 160-lead PQFP 66 E - - - - 98 G - - - - 67 E/ PD2 45 43 41 63 99 G 64 66 64 101 68 E - - - 64 100 G - - - 102 69 E 46 44 42 65 101 G 65 67 65 103 70 E - 46 44 67 102 G - 69 67 105 71 E - - - - 103 G - - - - 72 E 48 47 45 68 104 G 67 70 68 106 73 E 49 48 46 69 105 G 68 71 69 107 74 E - - - - 106 G - - - - 75 E 50 49 47 70 107 G 69 72 70 108 76 E - - - 71 108 G - - - 109 77 E 51 50 48 72 109 G 70 73 71 110 78 E - 51 49 73 110 G - 74 72 111 79 E - - - - 111 G - - - - 80 E 52 52 50 78 112 G/ TDO 71 75 73 112 81 F - 54 52 80 113 H - 77 75 121 82 F - - - - 114 H - - - - 83 F 54 55 53 88 115 H 73 78 76 122 84 F - - - 89 116 H - - - 123 85 F 55 56 54 90 117 H 74 79 77 128 86 F 56 57 55 91 118 H 75 80 78 129 87 F - - - - 119 H - - - - 88 F 57 58 56 92 120 H 76 81 79 130 89 F - 59 57 93 121 H - 82 80 131 90 F - - - - 122 H - - - - 91 F 58 60 58 94 123 H 77 83 81 132 92 F - - - 96 124 H - - - 134 93 F 60 62 60 97 125 H 79 85 83 135 94 F 61 63 61 98 126 H 80 86 84 136 95 F - - - - 127 H - - - - 96 F/ TCK 62 64 62 99 128 H/ GCLK3 81 87 85 137 23 0784P-PLD-7/05 Ordering Information ATF1508AS Standard Package Options tPD (ns) 7.5 10 10 15 15 Notes: tCO1 (ns) 4.5 5 fMAX (MHz) 166.7 125 5 125 5 100 8 100 Ordering Code Package ATF1508AS-7 JC84 84J ATF1508AS-7 QC100 100Q1 ATF1508AS-7 AC100 100A ATF1508AS-7 QC160 160Q1 ATF1508AS-10 JC84 84J ATF1508AS-10 QC100 100Q1 ATF1508AS-10 AC100 100A ATF1508AS-10 QC160 160Q1 ATF1508AS-10 Jl84 ATF1508AS-10 Ql100 ATF1508AS-10 Al100 ATF1508AS-10 Ql160 84J 100Q1 100A 160Q1 ATF1508AS-15 JC84 84J ATF1508AS-15 QC100 100Q1 ATF1508AS-15 AC100 100A ATF1508AS-15 QC160 160Q1 ATF1508AS-15 JI84 ATF1508AS-15 QI100 84J 100Q1 ATF1508AS-15 AI100 100A ATF1508AS-15 QI160 160Q1 Operation Range Commercial (0C to 70C) Commercial (0C to 70C) Industrial (-40C to +85C) Commercial (0C to 70C) Industrial (-40C to +85C) 1. The last time buy is Sept. 30, 2005 for shaded parts. 2. The recommended replacement package for QC160 is the AU100. Using "C" Product for Industrial To use commercial product for Industrial temperature ranges, down-grade one speed grade from the "I" to the "C" device (7 ns "C" = 10 ns "I") and de-rate power by 30%. ATF1508AS Green Package Options (Pb/Halide-free/RoHS Compliant) tPD (ns) tCO1 (ns) fMAX (MHz) Ordering Code Package 7.5 4.5 166.7 ATF1508AS-7 JX84 ATF1508AS-7 AX100 84J 100A 10 5 125 ATF1508AS-10 JU84 ATF1508AS-10 QU100 ATF1508AS-10 AU100 84J 100Q1 100A Operation Range Commercial (0C to 70C) Industrial (-40C to +85C) Package Type 84J 84-lead, Plastic J-leaded Chip Carrier (PLCC) 100Q1 100-lead, Plastic Quad Pin Flat Package (PQFP) 100A 100-lead, Very Thin Plastic Gull Wing Quad Flat Package (TQFP) 160Q1 160-lead, Plastic Quad Pin Flat Package (PQFP) 24 ATF1508AS(L) 0784P-PLD-7/05 ATF1508AS(L) ATF1508ASL Standard Package Options tPD (ns) tCO1 (ns) fMAX (MHz) Ordering Code Package ATF1508ASL-20 JC84 20 12 83.3 25 Note: 15 70 84J ATF1508ASL-20 QC100 100Q1 ATF1508ASL-20 AC100 100A ATF1508ASL-20 QC160 160Q1 ATF1508ASL-25 JI84 Operation Range Commercial (0C to 70C) 84J ATF1508ASL-25 QI100 100Q1 ATF1508ASL-25 AI100 100A ATF1508ASL-25 QI160 160Q1 Industrial (-40C to +85C) 1. The last time buy is Sept. 30, 2005 for shaded parts. Using "C" Product for Industrial To use commercial product for Industrial temperature ranges, down-grade one speed grade from the "I" to the "C" device (7 ns "C" = 10 ns "I") and de-rate power by 30%. ATF1508ASL Green Package Options (Pb/Halide-free/RoHS Compliant) tPD (ns) tCO1 (ns) fMAX (MHz) 25 15 70 Ordering Code Package ATF1508ASL-25 JU84 ATF1508ASL-25 AU100 84J 100A Operation Range Industrial (-40C to +85C) Package Type 84J 84-lead, Plastic J-leaded Chip Carrier (PLCC) 100Q1 100-lead, Plastic Quad Pin Flat Package (PQFP) 100A 100-lead, Very Thin Plastic Gull Wing Quad Flat Package (TQFP) 160Q1 160-lead, Plastic Quad Pin Flat Package (PQFP) 25 0784P-PLD-7/05 Package Information 84J - PLCC 1.14(0.045) X 45 PIN NO. 1 1.14(0.045) X 45 0.318(0.0125) 0.191(0.0075) IDENTIFIER E1 D2/E2 B1 E B e A2 D1 A1 D A 0.51(0.020)MAX 45 MAX (3X) COMMON DIMENSIONS (Unit of Measure = mm) Notes: 1. This package conforms to JEDEC reference MS-018, Variation AF. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is .010"(0.254 mm) per side. Dimension D1 and E1 include mold mismatch and are measured at the extreme material condition at the upper or lower parting line. 3. Lead coplanarity is 0.004" (0.102 mm) maximum. SYMBOL MIN NOM MAX A 4.191 - 4.572 A1 2.286 - 3.048 A2 0.508 - - D 30.099 - 30.353 D1 29.210 - 29.413 E 30.099 - 30.353 E1 29.210 - 29.413 D2/E2 27.686 - 28.702 B 0.660 - 0.813 B1 0.330 - 0.533 e NOTE Note 2 Note 2 1.270 TYP 10/04/01 R 26 2325 Orchard Parkway San Jose, CA 95131 TITLE 84J, 84-lead, Plastic J-leaded Chip Carrier (PLCC) DRAWING NO. REV. 84J B ATF1508AS(L) 0784P-PLD-7/05 ATF1508AS(L) 100Q1 - PQFP E PIN 1 ID PIN 1 e D1 B D E1 COMMON DIMENSIONS (Unit of Measure = mm) JEDEC STANDARD MS-022, GC-1 A 0~7 C L A1 SYMBOL MIN NOM MAX A - 3.04 3.4 A1 0.25 0.33 0.5 D 23.20 BSC E 17.20 BSC E1 14.00 BSC B 0.22 C 0.11 D1 L e NOTE - 0.40 - 0.23 20 BSC 0.73 - 1.03 0.65 BSC 07/6/2005 R DRAWING NO. TITLE 2325 Orchard Parkway 100Q1, 100-lead, 14 x 20 mm Body, 3.2 mm Footprint, 0.65 mm Pitch, 100Q1 San Jose, CA 95131 Plastic Quad Flat Package (PQFP) REV. C 27 0784P-PLD-7/05 100A - TQFP PIN 1 B PIN 1 IDENTIFIER E1 e E D1 D C 0~7 A1 A2 A L COMMON DIMENSIONS (Unit of Measure = mm) Notes: 1. This package conforms to JEDEC reference MS-026, Variation AED. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is 0.25 mm per side. Dimensions D1 and E1 are maximum plastic body size dimensions including mold mismatch. 3. Lead coplanarity is 0.08 mm maximum. SYMBOL MIN NOM MAX A - - 1.20 A1 0.05 - 0.15 A2 0.95 1.00 1.05 D 15.75 16.00 16.25 D1 13.90 14.00 14.10 E 15.75 16.00 16.25 E1 13.90 14.00 14.10 B 0.17 - 0.27 C 0.09 - 0.20 L 0.45 - 0.75 e NOTE Note 2 Note 2 0.50 TYP 10/5/2001 R 28 2325 Orchard Parkway San Jose, CA 95131 TITLE 100A, 100-lead, 14 x 14 mm Body Size, 1.0 mm Body Thickness, 0.5 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP) DRAWING NO. 100A REV. C ATF1508AS(L) 0784P-PLD-7/05 ATF1508AS(L) 160Q1 - PQFP D1 D E E1 Top View Bottom View A2 A1 e b COMMON DIMENSIONS (Unit of Measure = mm) L1 SYMBOL Side View Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MS-022, Variation DD-1, for additional information. 2. To be determined at seating plane. 3. Regardless of the relative size of the upper and lower body sections, dimensions D1 and E1 are determined at the largest feature of the body exclusive of mold Flash and gate burrs, but including any mismatch between the upper and lower sections of the molded body. 4. Dimension b does not include Dambar protrusion. The Dambar protrusion(s) shall not cause the lead width to exceed b maximum by more than 0.08 mm. Dambar cannot be located on the lower radius or the lead foot. 5. A1 is defined as the distance from the seating plane to the lowest point of the package body. MIN NOM MAX A1 0.25 - 0.50 A2 3.20 3.40 3.60 D NOTE 5 31.20 BSC 2 D1 28.00 BSC 3 E 31.20 BSC 2 E1 28.00 BSC 3 e 0.65 BSC b 0.22 L1 - 0.40 4 1.60 REF 3/28/02 R 2325 Orchard Parkway San Jose, CA 95131 TITLE 160Q1, 160-lead, 28 x 28 mm Body, 3.2 Form Opt., Plastic Quad Flat Pack (PQFP) DRAWING NO. 160Q1 REV. A 29 0784P-PLD-7/05 Revision History 30 Revision Comments 0784P Green package options added. 0784O The ATF1508ASL-25 commercial speed offering was obsoleted in 2002 and replaced by the ATF1508ASL-20 commercial speed grade. ATF1508AS(L) 0784P-PLD-7/05 Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Regional Headquarters Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500 Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel: (852) 2721-9778 Fax: (852) 2722-1369 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Atmel Operations Memory 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 RF/Automotive Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany Tel: (49) 71-31-67-0 Fax: (49) 71-31-67-2340 Microcontrollers 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France Tel: (33) 2-40-18-18-18 Fax: (33) 2-40-18-19-60 ASIC/ASSP/Smart Cards 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France Tel: (33) 4-76-58-30-00 Fax: (33) 4-76-58-34-80 Zone Industrielle 13106 Rousset Cedex, France Tel: (33) 4-42-53-60-00 Fax: (33) 4-42-53-60-01 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743 Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL'S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL'S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel's products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. (c) Atmel Corporation 2005. All rights reserved. Atmel(R), logo and combinations thereof, Everywhere You Are (R) and others, are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. Printed on recycled paper. 0784P-PLD-7/05 xM