ABPMRRN060MGAA5 - HONEYWELL

Sensing and Internet of Things

ABP SERIES

Basic Board Mount Pressure Sensors

High Accuracy, Compensated/Ampliﬁed

60 mbar to 10 bar | 6 kPa to 1 MPa | 1 psi to 150 psi

Digital or Analog Output, Liquid Media Capable

DESCRIPTION

The ABP Series are piezoresistive silicon

pressure sensors offering a ratiometric

analog or digital output for reading

pressure over the specified full scale

pressure span and temperature range.

They are calibrated and temperature

compensated for sensor offset,

sensitivity, temperature effects and

accuracy errors (which include non-

linearity, repeatability and hysteresis)

using an on-board Application Specific

Integrated Circuit (ASIC). Calibrated

output values for pressure are updated

at approximately 1 kHz for analog and

2 kHz for digital. All products are

designed and manufactured according

to ISO 9001 standards.

• Dry gases option: The input port is

limited to non-corrosive, non-ionic

media (e.g., dry air, gases) and should

not be exposed to condensation. The

gases are limited to media compatible

with high temperature polyamide,

silicone, alumina ceramic, silicon, gold,

and glass.

• Liquid media option: Includes an

additional silicone-based gel coating

to protect the electronics under

port P1, which enables use with

non-corrosive liquids (e.g. water and

saline) and in applications where

condensation can occur. Since port P2

is designed for use with non-corrosive

liquids, this option is often suitable for

wet-wet differential sensing.

DIFFERENTIATION

• Enhanced accuracy helps the design

engineer fully understand the error in

measurement.

• Wide supply voltage range offers

design flexibility.

• Power consumption when utilizing

sleep mode option allows for use in

battery-powered applications.

VALUE TO CUSTOMERS

• Simplifies design-in: Small size

saves room on the PC board (PCB),

or simplifies design in smaller and

lower power devices. Meets Moisture

Sensitivity Level 1 requirements, which

allows for unlimited shelf life when

stored at <30 ºC/85 %RH and, under

most storage conditions, allows for

PCB soldering without any material

concern about solder joint quality due

FEATURES

• Measures gage and differential

pressures

• Total Error Band (see Figure 1): ±1.5 %FSS

• Liquid media option: Allows for wet/wet

operation on dual ported devices

• Industry-leading long-term stability:

±0.25 %FSS

• Industry-leading accuracy: ±0.25 %FSS BFSL

• Wide pressure range: 60 mbar to 10 bar

| 6 kPa to 1 MPa | 1 psi to 150 psi

• As small as 8 mm x 7 mm

• High burst pressures (see Table 7)

• Calibrated over temperature range of

0°C to 50°C [32°F to 122°F]

• Operates from a single power supply of

either 3.3 Vdc or 5.0 Vdc

• Output: Ratiometric analog or I2C- or

SPI-compatible 12-bit digital

• Power consumption: 2 µA typical when

utilizing sleep mode option

• Meets IPC/JEDEC J-STD-020D.1

Moisture Sensitivity Level 1 requirements

• REACH and RoHS compliant

• Options: Internal diagnostic function,

liquid media, sleep mode, temperature

output

• Sensor materials have been tested and

certified for these food safety standards:

- NSF-169

- BPA Free

- LFGB

32305128

Issue G

to aging of the sensor terminals, which

minimizes the concern about aging

of the terminals prior PCB assembly.

Pressure choices allow engineers

to select range required for their

application. Leadless SMT, SMT, and

DIP package options.

• Cost-effective: Small size helps

engineers reduce design and

manufacturing costs while maintaining

enhanced performance and reliability

of the systems they design.

• Accurate: Total Error Band (TEB) and

wide pressure range enable engineers

to optimize system performance by

improving resolution and system

accuracy. Optional internal diagnostics

validate that the sensor readings are

correct.

• Flexible: Supply voltage range, variety

of pressure units, types, and ranges,

output options, and wide operating

temperature range simplify use in the

application.

• Versatile: Wet-media compatibility,

sleep mode, and temperature

output options make the sensor a

versatile choice for Internet of Things

applications.

• Honeywell Brand: Utilize proprietary

Honeywell technology, and are

protected by multiple global patents.

• Food Safety Certification for North

America, Europe and Asia.

POTENTIAL APPLICATIONS

• Medical: CPAP, blood analysis, blood

pressure monitoring, breast pumps,

drug dosing, hospital beds, massage

machines, oxygen concentrators,

patient monitoring, sleep apnea

equipment, urine analyzers,

ventilators/portable ventilators, and

wound therapy

• Industrial: Air brakes, HVAC/

transmitters, life sciences, material

handling, pneumatic control and

regulation, process gas monitoring,

and valve positioning/positioners

• Commercial: Air beds, coffee makers,

and washing machines

PORTFOLIO

Honeywell offers a variety

of board mount pressure sensors for

potential use in medical and industrial

applications. To view the entire product

portfolio, click here.

2Sensing and Internet of Things

BASIC BOARD MOUNT PRESSURE SENSORS, ABP SERIES

FIGURE 1. TOTAL ERROR BAND

TABLE 1. ABSOLUTE MAXIMUM RATINGS1

CHARACTERISTIC MIN. MAX. UNIT

Supply voltage (Vsupply)-0.3 6.0 Vdc

Voltage on any pin -0.3 Vsupply + 0.3 V

Digital interface clock frequency:

I2C

SPI

100

50

400

800

kHz

ESD susceptibility (human body model) 2 — kV

Storage temperature -40 [-40] 85 [185] °C [°F]

Soldering time and temperature:

lead solder temperature (DIP)

peak reflow temperature (Leadless SMT, SMT)

4 s max. at 250°C [482°F]

15 s max. at 250°C [482°F]

1Absolute maximum ratings are the extreme limits the device will withstand without damage.

TABLE 2. ENVIRONMENTAL SPECIFICATIONS

CHARACTERISTIC PARAMETER

Humidity:

all external surfaces

internal surfaces of Liquid Media Option (T, V, B, C, F, G)

internal surfaces of Dry Gases Option (N, D)

0 %RH to 95 %RH, non-condensing

0 %RH to 100 %RH, condensing

0 %RH to 95 %RH, non-condensing

Vibration 15 g, 10 Hz to 2 kHz

Shock 100 g, 6 ms duration

Life11 million pressure cycles minimum

Solder reflow J-STD-020-D.1 Moisture Sensitivity Level 1

(unlimited shelf life when stored at <30°C/85 %RH)

Certification (silicone gel coating option: Port 1 only) NSF-169, BPA Free, LFGB

1Life may vary depending on specific application in which the sensor is used.

TABLE 4. SENSOR PRESSURE TYPES

PRESSURE TYPE DESCRIPTION

Gage Output is proportional to the difference between applied pressure and atmospheric (ambient) pressure.

Differential Output is proportional to the difference between the pressures applied to each port (Port 1 – Port 2).

TABLE 3. WETTED MATERIALS1

COMPONENT PRESSURE PORT 1 (P1) PRESSURE PORT 2 (P2)

DRY GAS OPTION LIQUID MEDIA OPTION

Ports and covers high temperature polyamide

Metal gel ring —304 SST 

Substrate alumina ceramic —alumina ceramic

Adhesives epoxy, silicone epoxy, silicone gel epoxy, silicone

Electronic components silicon, glass, gold,

aluminum silicon

1Contact Honeywell Customer Service for detailed material information.

Total Error Band (TEB) is a single specification that includes

all possible sources of error. TEB should not be confused with

accuracy, which is actually a component of TEB. TEB is the worst

error that the sensor could experience. The TEB specification

on a datasheet may be confusing. Honeywell uses the TEB

specification in its datasheet because it is the most comprehensive

measurement of a sensor’s true accuracy. Honeywell also

provides the accuracy specification in order to provide a common

comparison with competitors’ literature that does not use the

TEB specification. Many competitors do not use TEB—they simply

specify the accuracy of their device. Their accuracy specification,

however, may exclude certain parameters. On their datasheet, the

errors are listed individually. When combined, the total error (or

what would be TEB) can be significant.

Total

Error

Band

Accuracy

BFSL

All Possible Errors

Thermal Hysteresis

Thermal Effect on Offset

Thermal Effect on Span

Pressure Non-Linearity

Pressure Hysteresis

Full Scale Span

Offset

Pressure Non-Repeatibility

3

Sensing and Internet of Things

BASIC BOARD MOUNT PRESSURE SENSORS, ABP SERIES

TABLE 5. OPERATING SPECIFICATIONS

CHARACTERISTIC ANALOG DIGITAL UNIT

MIN. TYP. MAX. MIN. TYP. MAX.

Supply voltage (Vsupply):1, 2, 3

3.3 Vdc

5.0 Vdc

3.0

4.75

3.3

5.0

3.6

5.25

3.0

4.75

3.3

5.0

3.6

5.25

Vdc

Supply current:

3.3 Vdc

5.0 Vdc

sleep mode option

—

2.1

2.7

—

2.8

3.8

—

3.1

3.7

1

3.9

4.6

10

mA

µA

Operating temperature range4-40 [-40] —85 [185] -40 [-40] —85 [185] °C [°F]

Compensated temperature range50 [-32] —50 [122] 0 [-32] —50 [122] °C [°F]

Temperature output option6— — — — ±4 — °C

Startup time (power up to data ready) — — 5 — — 3 ms

Response time — 1 — — 0.46 — ms

Clipping limit:

upper

lower

—

2.5

—

97.5

—

%Vsupply

I2C/SPI voltage level:

low

high

—

80

—

20

—

%Vsupply

Pull up on SDA/MISO, SCL/SCLK, SS — — — 1 — — kOhm

Total Error Band7— — ±1.5 — — ±1.5 %FSS8

Accuracy9— — ±0.25 — — ±0.25 %FSS BFSL

Long term stability (1000 hr, 25°C [77°F]) — — ±0.25 — — ±0.25 %FSS

Output resolution 0.03

—

12

—

%FSS

bits

1Sensors are either 3.3 Vdc or 5.0 Vdc based on the catalog listing selected.

2Ratiometricity of the sensor (the ability of the device output to scale to the supply voltage) is achieved within the specified

operating voltage.

3The sensor is not reverse polarity protected. Incorrect application of supply voltage or ground to the wrong pin may cause

electrical failure.

4Operating temperature range: The temperature range over which the sensor will produce an output proportional to pressure.

5Compensated temperature range: The temperature range over which the sensor will produce an output proportional to

pressure within the specified performance limits.

6Temperature output option: Typical temperature output error over the compensated temperature range of 0°C to 50°C.

Operation in Sleep Mode may affect temperature output error depending on duty cycle.

7Total Error Band: The maximum deviation from the ideal transfer function over the entire compensated temperature and

pressure range. Includes all errors due to offset, full scale span, pressure non-linearity, pressure hysteresis, repeatability,

thermal effect on offset, thermal effect on span, and thermal hysteresis.

8Full Scale Span (FSS): The algebraic difference between the output signal measured at the maximum (Pmax.) and minimum

(Pmin.) limits of the pressure range. (See Figure 2.)

9Accuracy: The maximum deviation in output from a Best Fit Straight Line (BFSL) fitted to the output measured over the

pressure range at 25°C [77°F]. Includes all errors due to pressure non-linearity, pressure hysteresis, and non-repeatability.

TABLE 6. SENSOR OUTPUT AT SIGNIFICANT PERCENTAGES (DIGITAL VERSIONS ONLY)

% OUTPUT DIGITAL COUNTS

DECIMAL HEX

0 0 0x0000

10 1638 0x0666

50 8192 0x2000

90 14746 0x399A

100 16383 0x3FFF

4Sensing and Internet of Things

BASIC BOARD MOUNT PRESSURE SENSORS, ABP SERIES

FIGURE 2. TRANSFER FUNCTION LIMITS1

Analog Versions

Digital Versions

1Transfer Function “A” is shown. See Figure 3 for other available transfer functions.

0

10

20

30

40

50

60

70

80

90

100

12345678910

1.5% Total Error Band

0

P

min.

P

max.

Compensated Pressure Range

Pressure (example unit)

Output (%Vsupply)

0.8 x Vsupply

P

max.

– P

min.

Output (V) = x (Pressure

applied

– P

min.

) + 0.10 x Vsupply

Ideal

80%

P

max.

– P

min.

Output (% of 2

14

counts) = x (Pressure

applied

– P

min.

) + 10%

Output (% of 2

14

counts)

0

10

20

30

40

50

60

70

80

90

100

12345678910

Pressure (example unit)

0

P

min.

P

max.

Compensated Pressure Range

1.5% Total Error Band

Ideal

5

Sensing and Internet of Things

BASIC BOARD MOUNT PRESSURE SENSORS, ABP SERIES

FIGURE 3. NOMENCLATURE AND ORDER GUIDE

ABP D NN N 150PG A A 3

Product Series

Package

Pressure Port

DIP

ABP Ampliﬁed Basic

Option

SMT

NN

Leadless SMT

AN

LN

Single axial

barbed port

Single axial

barbless port

No port

NN

AN

LN

Single axial

barbed port

Single axial

barbless port

No port

NN

AN

LN

Single axial

barbed port

Single axial

barbless port

No port

Output Type

Supply Voltage

For example, ABPDNNN150PGAA3 deﬁnes an ABP Series Ampliﬁed Basic Pressure Sensor, DIP package, NN pressure port,

dry gases only, no diagnostics, 150 psi gage pressure range, analog output type, 10% to 90% of Vsupply (analog), transfer

function, no temperature output, no sleep mode, 3.3 Vdc supply voltage.

Pressure Range1, 2

1 Custom pressure ranges are available. Contact Honeywell Customer Service for more information.

2 See the explanation of sensor pressure types in Table 4.

3 The Transfer Function limits deﬁne the output of the sensor at a given pressure input. By specifying Pmin. and Pmax., the output at Pmin. and Pmax., the complete transfer function of the sensor

is deﬁned. See the graphical representations of the transfer function in Figure 3.

4 Custom gel options are available. Contact Honeywell Customer Service for more information.

1 psi to 150 psi

60 mbar to 10 bar

DifferentialDifferential

Gage

001PD

005PD

015PD

030PD

060PD

Gage

001PG

005PG

015PG

030PG

060PG

100PG

150PG

060MD

100MD

160MD

250MD

400MD

600MD

001BD

1.6BD

2.5BD

004BD

060MG

100MG

160MG

250MG

400MG

600MG

001BG

1.6BG

2.5BG

004BG

006BG

010BG

±60 mbar

±100 mbar

±160 mbar

±250 mbar

±400 mbar

±600 mbar

±1 bar

±1.6 bar

±2.5 bar

±4 bar

0 mbar to 60 mbar

0 mbar to 100 mbar

0 mbar to 160 mbar

0 mbar to 250 mbar

0 bar to 400 mbar

0 bar to 600 mbar

0 bar to 1 bar

0 bar to 1.6 bar

0 bar to 2.5 bar

0 bar to 4 bar

0 bar to 6 bar

0 bar to 10 bar

6 kPa to 1 MPa

Differential

Gage

006KD

010KD

016KD

025KD

040KD

060KD

100KD

160KD

250KD

400KD

006KG

010KG

016KG

025KG

040KG

060KG

100KG

160KG

250KG

400KG

600KG

001GG

±6 kPa

±10 kPa

±16 kPa

±25 kPa

±40 kPa

±60 kPa

±100 kPa

±160 kPa

±250 kPa

±400 kPa

0 kPa to 6 kPa

0 kPa to 10 kPa

0 kPa to 16 kPa

0 kPa to 25 kPa

0 kPa to 40 kPa

0 kPa to 60 kPa

0 kPa to 100 kPa

0 kPa to 160 kPa

0 kPa to 250 kPa

0 kPa to 400 kPa

0 kPa to 600 kPa

0 kPa to 1 MPa

0 psi to 1 psi

0 psi to 5 psi

0 psi to 15 psi

0 psi to 30 psi

0 psi to 60 psi

0 psi to 100 psi

0 psi to 150 psi

±1 psi

±5 psi

±15 psi

±30 psi

±60 psi

Transfer Function3

A

10% to 90% of Vsupply (analog), 214 counts (digital)

no temperature output, no sleep mode

A

S

0

1

2

Analog

SPI

I2C, Address 0x08

I2C, Address 0x18

I2C, Address 0x28

Dry gases only, no diagnostics

Dry gases only, diagnostics on

D

Liquid media, no diagnostics

T

Liquid media, diagnostics on

V

D

S

10% to 90% of 214 counts (digital only)

no temperature output, sleep mode enabled

3

4

5

6

7

I2C, Address 0x38

I2C, Address 0x48

I2C, Address 0x58

I2C, Address 0x68

I2C, Address 0x78

JN

Single radial

barbless port

JN

Single radial

barbless port

JJ

Dual radial

barbless ports,

same side

JJ

Dual radial

barbless ports,

same side

RN

Single radial

barbed port

RN

Single radial

barbed port

RR

Dual radial

barbed ports,

same side

RR

Dual radial

barbed ports,

same side

10% to 90% of 214 counts (digital only)

temperature output enabled, sleep mode enabled

T

10% to 90% of 214 counts (digital only)

temperature output enabled, no sleep mode

B

C

F

G

Liquid media, food grade gel, no diagnostics

4

Liquid media, food grade gel, diagnostics on

4

Liquid media, ﬂuorosilicone gel, no diagnostics

4

Liquid media, ﬂuorosilicone gel, diagnostics on

4

N

D

M

L

DIP (Dual Inline Pin)

SMT (Surface Mount Technology)

Leadless SMT

3

5

3.3 Vdc

5.0 Vdc

6Sensing and Internet of Things

BASIC BOARD MOUNT PRESSURE SENSORS, ABP SERIES

TABLE 7. PRESSURE RANGE SPECIFICATIONS

PRESSURE

RANGE

(SEE FIGURE 3.)

PRESSURE RANGE

UNIT

OVERPRESSURE1BURST PRESSURE2COMMON

MODE

PRESSURE3

PMIN. PMAX. PORT 1 (P1) PORT 2 (P2) PORT 1 (P1) PORT 2 (P2)

1 psi to 150 psi

Differential

060MD -60 60 mbar 2000 850 3500 1000 10000

100MD -100 100 mbar 4000 1400 7000 2500 10000

160MD -160 160 mbar 4000 1400 7000 2500 10000

250MD -250 250 mbar 10000 2000 19000 4000 10000

400MD -400 400 mbar 10000 2000 19000 4000 10000

600MD -600 600 mbar 17000 2000 19000 4000 10000

001BD -1 1bar 17 419 817

1.6BD -1.6 1.6 bar 17 819 16 17

2.5BD -2.5 2.5 bar 17 819 16 17

004BD -4.0 4.0 bar 17 16 19 19 17

Gage

060MG 060 mbar 2000 —3500 —5500

100MG 0100 mbar 2000 —3500 —10000

160MG 0160 mbar 2000 —3500 —10000

250MG 0250 mbar 4000 —7000 —10000

400MG 0400 mbar 10000 —19000 —10000

600MG 0600 mbar 10000 —19000 —10000

001BG 0 1 bar 17 —19 —17

1.6BG 01.6 bar 17 —19 —17

2.5BG 02.5 bar 17 —19 —17

004BG 0 4 bar 17 —19 —17

006BG 0 6 bar 17 —19 —17

010BG 010 bar 17 —19 —17

6 kPa to 1 MPa

Differential

006KD -6 6kPa 200 85 350 100 1000

010KD -10 10 kPa 400 140 700 250 1000

016KD -16 16 kPa 400 140 700 250 1000

025KD -25 25 kPa 1000 200 1900 400 1000

040KD -40 40 kPa 1000 200 1900 400 1000

060KD -60 60 kPa 170 0 200 1900 400 1000

100KD -10 0 100 kPa 170 0 400 1900 800 1700

160KD -160 160 kPa 170 0 800 1900 1600 170 0

250KD -250 250 kPa 170 0 800 1900 1600 170 0

400KD -400 400 kPa 170 0 1600 1900 1900 1700

Gage

006KG 0 6 kPa 200 —350 —550

010KG 010 kPa 200 —350 —1000

016KG 016 kPa 200 —350 —1000

025KG 025 kPa 400 —700 —1000

040KG 040 kPa 1000 —1900 —1000

060KG 060 kPa 1000 —1900 —1000

100KG 0100 kPa 1700 —1900 —170 0

160KG 0160 kPa 170 0 —1900 —1700

250KG 0250 kPa 1700 —1900 —170 0

400KG 0400 kPa 170 0 —1900 —170 0

600KG 0600 kPa 170 0 —1900 —170 0

001GG 0 1 MPa 1.7 —1.9 —1.7

7

Sensing and Internet of Things

BASIC BOARD MOUNT PRESSURE SENSORS, ABP SERIES

TABLE 7. PRESSURE RANGE SPECIFICATIONS (CONTINUED)

PRESSURE

RANGE

(SEE FIGURE 3.)

PRESSURE RANGE

UNIT

OVERPRESSURE1BURST PRESSURE2COMMON

MODE

PRESSURE3

PMIN. PMAX.Port 1 (P1) Port 2 (P2) Port 1 (P1) Port 2 (P2)

1 psi to 150 psi

Differential

001PD -1 1psi 30 10 50 15 150

005PD -5 5psi 150 30 275 40 150

015PD -15 15 psi 250 60 275 120 250

030PD -30 30 psi 250 120 275 240 250

060PD -60 60 psi 250 250 275 275 250

Gage

001PG 0 1 psi 30 —50 —150

005PG 0 5 psi 150 —275 —150

015PG 015 psi 250 —275 —250

030PG 030 psi 250 —275 —250

060PG 060 psi 250 —275 —250

100PG 0100 psi 250 —275 —250

150PG 0150 psi 250 —275 —250

1Overpressure: The maximum pressure which may safely be applied to the product for it to remain in specification once pressure is returned to the

operating pressure range. Exposure to higher pressures may cause permanent damage to the product. Unless otherwise specified this applies to all

available pressure ports at any temperature with the operating temperature range.

2Burst pressure: The maximum pressure that may be applied to the specified port (P1 or P2) of the product without causing escape of pressure

media. Product should not be expected to function after exposure to any pressure beyond the burst pressure.

3Common mode pressure: The maximum pressure that can be applied simultaneously to both ports of a differential pressure sensor without causing

changes in specified performance.

FIGURE 4. RECOMMENDED FILTER CAP

V

SUPPLY

VSUPPLY

VOUT*

Ground

*Analog output version only

.

0.1



F

0.001 F*

8Sensing and Internet of Things

BASIC BOARD MOUNT PRESSURE SENSORS, ABP SERIES

FIGURE 5. DIP PACKAGE DIMENSIONAL DRAWINGS (FOR REFERENCE ONLY: MM [IN].)

DIP NN: No port

DIP AN: Single axial barbed port

8,6

[0.34]

11,0

[0.43]

7,3

[0.29]

2X 1,45

[0.057]

2,54 Typ.

[0.100]

8,0

[0.32]

3,23 Wet media

[0.127]

2,95 Dry media

[0.116]

11,5

[0.45]

3,81

[0.150]

0,25 Typ.

[0.010]

6,3

[0.25]

4,0

[0.16]

5,5

[0.22]

6X 0,46

[0.018]

4 5 6

3 2 1 1,0

[0.04]

6 5 4

1 2 3

2X 1,45

[0.057]

0,25 Typ.

[0.010]

11,0

[0.43]

11,5

[0.45]

2,54 Typ.

[0.100]

3,63 Wet media

[0.143]

3,35 Dry media

[0.131]

6,3

[0.25]

7,3

[0.29]

5,5

[0.22]

3,81

[0.150]

8,6

[0.34]

8,0

[0.32]

1,0

[0.04]

7,00

[0.276]

6X 0,46

[0.018]

ø2,32

[0.091]

ø1,91

[0.075]

ø2,74

[0.108]

3,56

[0.140]

4,0

[0.16]

4 5 6

3 2 1

6 5 4

1 2 3

9

Sensing and Internet of Things

BASIC BOARD MOUNT PRESSURE SENSORS, ABP SERIES

FIGURE 5. DIP PACKAGE DIMENSIONAL DRAWINGS (CONTINUED)

DIP LN: Single axial

barbless port

DIP JN: Single radial

barbless port

0,25 Typ.

[0.010]

11,0

[0.43]

11,5

[0.45]

8,0

[0.32]

2,54 Typ.

[0.100]

3,23 Wet media

[0.127]

2,95 Dry media

[0.116]

8,6

[0.34]

1,0

[0.04]

4,80

[0.189]

7,3

[0.29]

4,0

[0.16]

5,5

[0.22]

3,81

[0.150]

ø5,00

[0.197]

2,68

[0.106]

6X 0,46

[0.018]

2X 1,45

[0.057]

6X 0,46

[0.018]

6,3

[0.25]

4 5 6

3 2 1

6 5 4

1 2 3

11,0

[0.43]

11,5

[0.45]

0,25 Typ.

[0.010]

8,0

[0.32]

8,6

[0.34]

3,38 Wet media

[0.133]

3,10 Dry media

[0.122]

3,81

[0.150]

6X 0,46

[0.018]

4,45

[0.175]

4,65

[0.183]

1,0

[0.04]

7,3

[0.29]

6,3

[0.25]

4 5 6

3 2 1

2.16

[0.085]

0,7

[0.03

6 5 4

1 2 3

2X 1,45

[0.057]

2,54 Typ.

[0.100]

ø1,88

[0.074]

10 Sensing and Internet of Things

BASIC BOARD MOUNT PRESSURE SENSORS, ABP SERIES

FIGURE 5. DIP PACKAGE DIMENSIONAL DRAWINGS (CONTINUED)

DIP JJ: Dual radial

barbless ports, same side

DIP RN: Single radial

barbed port

DIP RR: Dual radial

barbed ports, same side

0,25 Typ.

[0.010]

11,0

[0.43]

11,5

[0.45]

8,0

[0.32]

2,54 Typ.

[0.100]

8,6

[0.34]

3,38 Wet media

[0.133]

3,10 Dry media

[0.122]

Port 2

Port 1

Port 2

Port 1 4,45

[0.175]

2,82

[0.111]

1,0

[0.04]

3,81

[0.150]

6X 0,46

[0.018]

7,3

[0.29]

2X 1,47

[0.058]

2X 4,65

[0.183]

4,45

[0.175]

5,06 Wet media

[0.199]

4,78 Dry media

[0.188]

6,3

[0.25]

2,10

[0.083]

4 5 6

3 2 1

0,7

[0.03

6 5 4

1 2 3

2X 4,0

[0.16]

2X ø1,88

[0.074]

11,0

[0.43]

11,5

[0.45]

0,25 Typ.

[0.010]

8,0

[0.32]

2,54 Typ.

[0.100]

1,65

[0.065]

4,55

[0.179]

4,75

[0.187]

3,58 Wet media

[0.141]

3,30 Dry media

[0.129]

8,6

[0.34]

2,01

[0.079]

3,81

[0.150]

6X 0,46

[0.018]

7,3

[0.29]

6,3

[0.25]

0,5

[0.02]

ø1,60

[0.063]

ø2,10

[0.083]

ø1,75

[0.069]

4,0

[0.16]

3,10

[0.122]

4 5 6

3 2 1

6 5 4

1 2 3

2X 1,47

[0.058]

0,25 Typ.

[0.010]

11,0

[0.43]

11,5

[0.45]

8,0

[0.32]

8,6

[0.34]

4,55

[0.179]

3,58 Wet media

[0.141]

3,30 Dry media

[0.129]

1.0

[0.04]

6,3

[0.25]

2,78

[0.109]

7,3

[0.29]

3,81

[0.150]

0,5

[0.02]

4,55

[0.179]

4,76

[0.187]

6X 0,46

[0.018]

2,54 Typ.

[0.100]

Port 2

Port 1

Port 2

1,90

[0.075]

2X 4,0

[0.16]

2X ø1,60

[0.063]

2X ø1,75

[0.069]

4 5 6

3 2 1

2X ø2,10

[0.083]

2X 4,75

[0.187]

2X 1.45

[0.057] 6 5 4

1 2 3

11

Sensing and Internet of Things

BASIC BOARD MOUNT PRESSURE SENSORS, ABP SERIES

FIGURE 6. SMT PACKAGE DIMENSIONAL DRAWINGS (FOR REFERENCE ONLY: MM [IN].)

SMT NN: No port

SMT AN: Single axial

barbed port

SMT LN: Single axial

barbless port

SMT JN: Single radial

barbless port

6 5 4

1 2 3

0,25 Typ.

[0.010]

11,0

[0.43]

11,5

[0.45]

4,2

[0.17]

1,0

[0.04]

8,0

[0.32]

4,0

[0.16]

7,3

[0.29]

5,5

[0.22]

6,3

[0.25]

4 5 6

3 2 1

4,80

[0.189]

3,23 Wet media

[0.127]

2,95 Dry media

[0.116]

ø5,00

[0.197]

2,68

[0.106]

6X 0,46

[0.018]

6X 1,28

[0.050]

2X 1,45

[0.057]

2,54 Typ.

[0.100]

6 5 4

1 2 3

0,25 Typ.

[0.010]

11,0

[0.43]

11,5

[0.45]

7,00

[0.276]

4,2

[0.17]

1,0

[0.04]

6,3

[0.25]

8.0

[0.32]

3,63 Wet media

[0.143]

3,35 Dry media

[0.131]

4,0

[0.16]

7,3

[0.29]

5,5

[0.22]

ø2,32

[0.091]

ø1,91

[0.075]

ø2,74

[0.108]

6X 0,46

[0.018]

6X 1,28

[0.050]

2X 1,45

[0.057]

2,54 Typ.

[0.100]

3,56

[0.140]

4 5 6

3 2 1

11,5

[0.45]

6X 0,46

[0.018]

6,3

[0.25]

4,0

[0.16]

1,0

[0.04]

8.0

[0.32]

3,23 Wet media

[0.127]

2,95 Dry media

[0.116]

11,0

[0.43]

7,3

[0.29]

5,5

[0.22]

4,2

[0.17]

6 5 4

1 2 3

0,25 Typ.

[0.010]

2X 1,45

[0.057]

2,54 Typ.

[0.100]

6X 1,28

[0.050]

4 5 6

3 2 1

6 5 4

1 2 3

0,25 Typ.

[0.010]

11,0

[0.43]

11,5

[0.45]

4,2

[0.17]

1,0

[0.04]

8,0

[0.32]

4,45

[0.175]

6,3

[0.25]

4,0

[0.16]

4,65

[0.183]

7,3

[0.29]

1,88

[0.074]

2,54 Typ.

[0.100]

2.16

[0.085]

1,47

[0.058]

0,7

[0.03]

3,38 Wet media

[0.133]

3,10 Dry media

[0.122]

6X 1,28

[0.050]

4 5 6

3 2 1 6X 0,46

[0.018]

12 Sensing and Internet of Things

BASIC BOARD MOUNT PRESSURE SENSORS, ABP SERIES

FIGURE 6. SMT PACKAGE DIMENSIONAL DRAWINGS (CONTINUED)

SMT JJ: Dual radial

barbless ports, same

side

SMT RN: Single radial

barbed port

SMT RR: Dual radial

barbed ports, both sides

0,25 Typ.

[0.010]

11,0

[0.43]

11,5

[0.45]

4,2

[0.17]

1,0

[0.04]

8,0

[0.32]

4.45

[0.175]

2,54 Typ.

[0.100]

2,10

[0.083

]6,3

[0.25]

7,3

[0.29]

0,7

[0.03]

3,38 Wet media

[0.133]

3,10 Dry media

[0.122]

Port 2

Port 1

Port 2

Port 1

4,45

[0.175]

6X 0,46

[0.018]

2X 1,88

[0.074]

6X 1,28

[0.050]

2X 1,45

[0.057]

2X 4.0

[0.16]

2X 4.65

[0.183] 5,06 Wet media

[0.199]

4,78 Dry media

[0.188]

6 5 4

1 2 3

4 5 6

3 2 1

2,82

[0.111]

11,0

[0.43]

11,5

[0.45]

4,2

[0.17]

1,0

[0.04]

8,0

[0.32]

0,25 Typ.

[0.010]

2,54 Typ.

[0.100]

7,3

[0.29]

6,3

[0.25]

1.65

[0.065]

4,75

[0.187]

4,55

[0.179]

0,5

[0.02]

4,0

[0.16]

ø1,60

[0.063]

ø2,10

[0.083]

ø1,75

[0.069]

6X 0,46

[0.018]

6X 1,28

[0.050]

2X 1,45

[0.057]

3,58 Wet media

[0.141]

3,30 Dry media

[0.129]

6 5 4

1 2 3

4 5 6

3 2 1

2,01

[0.079]

0,25 Typ.

[0.010]

11,0

[0.43]

11,5

[0.45]

4,2

[0.17]

1,0

[0.04]

8,0

[0.32]

2,54 Typ.

[0.100]

1,90

[0.075]

3,10

[0.122]

6,3

[0.25]

4,55

[0.179]

4,76

[0.187]

7,3

[0.29]

2,78

[0.109]

0,5

[0.02]

Port 2

Port 1

Port 2

Port 1

4,55

[0.179]

6X 0,46

[0.018]

6X 1,28

[0.050]

2X 1,45

[0.057]

2X 4.0

[0.16]

2X 4.75

[0.187]

3,58 Wet media

[0.141]

3,30 Dry media

[0.129]

2X ø1,60

[0.063]

2X ø1,75

[0.069]

6 5 4

1 2 3

4 5 6

3 2 1

2X ø2,10

[0.083]

13

Sensing and Internet of Things

BASIC BOARD MOUNT PRESSURE SENSORS, ABP SERIES

FIGURE 7. LEADLESS SMT PACKAGE DIMENSIONAL DRAWINGS (FOR REFERENCE ONLY: MM [IN].)

Leadless SMT NN: No port

Leadless SMT AN: Single

axial barbed port

Leadless SMT LN: Single

axial barbless port

6,3

[0.25]

2,5 Typ.

[0.10]

3 2 1

4 5 6

8,0

[0.32]

1,5

[0.06]

7,0

[0.28]

6X 1,25

[0.049]

6 5 4

1 2 3

7,3

[0.29]

3,63 Wet media

[0.14]

3,35 Dry media

[0.13]

4.0

[0.16]

3.5

[0.14]

3,56

[0.140]

7,0

[0.28]

3,00

[0.118]

1,0

[0.04]

ø1,91

[0.075] ø2,32

[0.091]

ø2,74

[0.108]

6,3

[0.25]

7,3

[0.29] 2,5 Typ.

[0.10]

3,23 Wet media

[0.13]

2,95 Dry media

[0.12]

3.5

[0.14]

4.0

[0.16]

3 2 1

4 5 6

8,0

[0.32]

1,5

[0.06]

0,7

[0.03]

3,00

[0.118]

ø5,0

[0.20]

ø2,68

[0.106]

4,1

[0.16]

7,0

[0.28]

1,0

[0.04]

6X 1,25

[0.049]

6 5 4

1 2 3

Port 1

2,5 Typ.

[0.10]

3 2 1

4 5 6

8,0

[0.32]

1,5

[0.06]

7,0

[0.28]

6X 1,25

[0.049]

6 5 4

1 2 3

3,00

[0.118]

6,3

[0.25]

7,3

[0.29]

3,23 Wet media

[0.13]

2,95 Dry media

[0.12]

4.0

[0.16]

3.5

[0.14]

1,0

[0.04]

FIGURE 8. RECOMMENDED PCB LAYOUTS

DIP SMT Leadless SMT

11,0

[0.433]

123

654

5,00

[0.197]

6,00

[0.236]

6X ø0.73

[0.029]

2,54

[0.1]

2,73

[0.1

07]

8,00

[0.315]

11,25

[0.443]

Gage reference hole: do not plug

7,00

[0.28]

3,00

[0.118]

2,50

[0.098]

2,73

[0.107]

8,00

[0.315]

4,00

[0.1

57] 3,25

0.128] 8,00

[0.315]

1,30

[0.051]

123

654

Gage reference hole: do not plug

5,00

[0.1

97]

6,00

[0.236]

2,54

[0.1]

2,73

[0.107]

8,00

[0.315]

11,00

[0.433]

8,85

[0.348]

12,35

[0.31

5]

1

2

3

65 4

0,65

[0.026]

Gage reference hole: do not plug

TABLE 8. PINOUTS

OUTPUT TYPE PIN 1 PIN 2 PIN 3 PIN 4 PIN 5 PIN 6

I2CGND Vsupply INT NC SDA SCL

SPI GND Vsupply SS NC MISO SCLK

analog GND NC Vout NC NC Vsupply

32305128-G-EN | G | 07/20

WARRANTY/REMEDY

Honeywell warrants goods of its manu-

facture as being free of defective materi-

als and faulty workmanship during the

applicable warranty period. Honeywell’s

standard product warranty applies un-

less agreed to otherwise by Honeywell in

writing; please refer to your order ac-

knowledgment or consult your local sales

office for specific warranty details. If war-

ranted goods are returned to Honeywell

during the period of coverage, Honeywell

will repair or replace, at its option, without

charge those items that Honeywell,

in its sole discretion, finds defective.

The foregoing is buyer’s sole remedy

and is in lieu of all other warranties,

expressed or implied, including those

of merchantability and fitness for a

particular purpose. In no event shall

Honeywell be liable for consequential,

special, or indirect damages.

While Honeywell may provide applica-

tion assistance personally, through our

literature and the Honeywell web site, it

is buyer’s sole responsibility to determine

the suitability of the product in the ap-

plication.

Specifications may change without

notice. The information we supply is

believed to be accurate and reliable as of

this writing. However, Honeywell assumes

no responsibility for its use.

m WARNING

PERSONAL INJURY

DO NOT USE these products as safety

or emergency stop devices or in any

other application where failure of the

product could result in personal injury.

Failure to comply with these

instructions could result in death or

serious injury.

m WARNING

MISUSE OF

DOCUMENTATION

• The information presented in this

product sheet is for reference only.

Do not use this document as a

product installation guide.

• Complete installation, operation,

and maintenance information

is provided in the instructions

supplied with each product.

Failure to comply with these

instructions could result in death or

serious injury.

ADDITIONAL MATERIALS

The following associated literature is

available at sensing.honeywell.com:

• Product range guide

• Installation instructions

• Application note

Honeywell

Sensing and Internet of Things

830 East Arapaho Road

Richardson, TX 75081

sensing.honeywell.com

FOR MORE INFORMATION

Honeywell Sensing and Internet of

Things services its customers through a

worldwide network of sales offices and

distributors. For application assistance,

current specifications, pricing or the

nearest Authorized Distributor,

visit sensing.honeywell.com or call:

USA/Canada +1 302 613 4491

Latin America +1 305 805 8188

Europe +44 1344 238258

Japan +81 (0) 3-6730-7152

Singapore +65 6355 2828

Greater China +86 4006396841