Datasheet 1A Variable / Fixed Output LDO Regulators BDxxIC0WEFJ / BDxxIC0WHFV General Description BDxxIC0W series devices are LDO regulators with an output current of 1.0A. The output accuracy is 1% of the output voltage. Both fixed and variable output voltage devices are available. The output voltage of the variable output voltage device can be varied from 0.8 to 4.5V using external resistors. Various fixed output voltage devices that do not use external resistors are also available. These LDO regulators are available in two package types: HTSOP-J8 (4.90mm x 6.00mm x 1.00mm) and HVSOF6 (1.60mm x 3.00mm x 0.75mm), and can be used in a wide variety of digital appliances. These devices have built in over current protection to protect the device when output is shorted, 0A shutdown mode and thermal shutdown circuit to protect the device during over load conditions. These LDO regulators are usable with ceramic capacitors that enable a smaller layout and longer life. Features +/-1% output voltage accuracy Built-in Over Current Protection circuit (OCP) Built-in Thermal Shut Down circuit (TSD) Zero A Shutdown mode Package HTSOP-J8 HVSOF6 (Typ.) (Typ.) (Max.) 4.90mm x 6.00mm x 1.00mm 1.60mm x 3.00mm x 0.75mm Key Specifications Input Power Supply Voltage range: 2.4V to 5.5V Output Voltage range(Variable type): 0.8V to 4.5V Output Voltage(Fixed type): 1.0V/1.2V/1.25V/1.5V 1.8V/2.5V/2.6V/3.0V/3.3V (1.25V/2.6V:HVSOF6 only) Output Current: 1.0A (Max.) Shutdown Current: 0 A (Typ.) Operating Temperature Range: -25 to +85 HTSOP-J8 HVSOF6 Typical Application Circuit VCC VO CIN VCC R1 COUT FB EN GND GND CIN,COUT : Ceramic Capacitor Output voltage variable type Product structureSilicon monolithic integrated circuit www.rohm.com (c) 2015 ROHM Co., Ltd. All rights reserved. TSZ2211114001 VO_S COUT EN R2 FIN VO CIN FIN CIN,COUT : Ceramic Capacitor Output voltage fixed type This product is not designed with protection against radioactive rays. 1/23 TSZ02201-GAG0A600030-1-2 19.Aug.2015 Rev.004 Datasheet BDxxIC0WEFJ / BDxxIC0WHFV Ordering Information B D x x Part Output Number voltage 00:Variable 10:1.0V 12:1.2V 1C:1.25V 15:1.5V 18:1.8V 25:2.5V 26:2.6V 30:3.0V 33:3.3V I C 0 W y y Package - zz Input voltage range Output current :7V C0:1.0A "W"included EFJ : HTSOP-J8 E2 : Emboss tape reel(HTSOP-J8) HFV : HVSOF6 GTR : Emboss tape reel(HVSOF6) www.rohm.com (c) 2015 ROHM Co., Ltd. All rights reserved. TSZ2211115001 Shutdown mode y 2/23 Packaging and forming specification TSZ02201-GAG0A600030-1-2 19.Aug.2015 Rev.004 Datasheet BDxxIC0WEFJ / BDxxIC0WHFV Block Diagram BD00IC0WEFJ / BD00IC0WHFV (Variable output voltage type) VCC OCP SOFT START VO FB EN TSD GND Fig.1 Block Diagram Pin Configuration and Pin Description (HTSOP-J8) Pin No. Pin name Pin Function 1 VO Output pin 2 FB Feedback pin 3 GND GND pin 4 N.C No Connect (Connect to GND or leave OPEN) 5 EN Enable pin 6 N.C No Connect (Connect to GND or leave OPEN) 7 N.C No Connect (Connect to GND or leave OPEN) 8 VCC Input pin Reverse FIN Substrate (Connect to GND) (HVSOF6) Pin No. 1 2 3 4 5 6 Reverse Pin name VO FB GND EN N.C VCC FIN Pin Function Output pin Feedback pin GND pin Enable pin No Connect (Connect to GND or leave OPEN) Input pin Substrate (Connect to GND) www.rohm.com (c) 2015 ROHM Co., Ltd. All rights reserved. TSZ2211115001 3/23 VO 1 8 VCC FB 2 7 N.C GND 3 6 N.C N.C 4 5 EN Vo 1 6 Vcc FB 2 5 N.C GND 3 4 EN TSZ02201-GAG0A600030-1-2 19.Aug.2015 Rev.004 Datasheet BDxxIC0WEFJ / BDxxIC0WHFV Block Diagram BDxxIC0WEFJ / BDxxIC0WHFV (Fixed output voltage type) VCC OCP SOFT START VO EN TSD VO_S GND Fig.2 Block Diagram Pin Configuration and Pin Description (HTSOP-J8) Pin No. Pin name Pin Function 1 VO Output pin 2 VO_S Output voltage monitor pin 3 GND GND pin 4 N.C No Connect (Connect to GND or leave OPEN) 5 EN Enable pin 6 N.C No Connect (Connect to GND or leave OPEN) 7 N.C No Connect (Connect to GND or leave OPEN) 8 VCC Input pin Reverse FIN Substrate (Connect to GND) VO 1 8 VCC VO_S 2 7 N.C GND 3 6 N.C N.C 4 5 EN (HVSOF6) Pin No. Pin name 1 2 3 4 5 6 Reverse VO VO_S GND EN N.C VCC FIN Pin Function Output pin Output voltage monitor pin GND pin Enable pin No Connect (Connect to GND or leave OPEN) Input pin Substrate (Connect to GND) www.rohm.com (c) 2015 ROHM Co., Ltd. All rights reserved. TSZ2211115001 4/23 VO 1 6 VCC VO_S 2 5 N.C GND 3 4 EN TSZ02201-GAG0A600030-1-2 19.Aug.2015 Rev.004 Datasheet BDxxIC0WEFJ / BDxxIC0WHFV Absolute Maximum Ratings (Ta=25) Parameter Power supply voltage EN voltage Symbol Ratings Unit VCC -0.3 to 7.0 *1 V VEN -0.3 to 7.0 V HTSOP-J8 Pd 2.11 *2 W HVSOF6 Pd 1.70 *3 W Operating Temperature Range Topr -25 to +85 Storage Temperature Range Tstg -55 to +150 Tjmax +150 Power dissipation Junction Temperature *1 Not to exceed Pd *2 Reduced by 16.9mW/ for each increase in Ta of 1 over 25. (when mounted on a board 70mmx70mmx1.6mm glass-epoxy board, two layer) *3 Reduced by 13.6mW/ for each increase in Ta of 1 over 25 . (when mounted on a board 70mm x 70mm x 1.6mm glass-epoxy board, single-layer(copper foil are :51%)) Recommended Operating Ratings (Ta=25) Parameter Symbol Ratings Min. Max. Unit Input power supply voltage VCC 2.4 5.5 V EN voltage VEN 0.0 5.5 V Output voltage setting range VO 0.8 4.5 V Output current IO 0.0 1.0 A Electrical Characteristics (Unless otherwise noted, Ta=25, EN=3V, VCC=3.3V, R1=16k, R2=7.5k) Limits Parameter Symbol Unit Conditions Min. Typ. Max. Circuit current at shutdown mode Bias current ISTB - 0 5 A ICC - 250 500 A Line regulation Reg.Ii -1 - 1 % Load regulation VEN=0V, OFF mode VCC=( VO+0.6V )5.5V Reg IO -1.5 - 1.5 % IO=01.0A Minimum dropout voltage1 VCO1 - 0.10 0.15 V VCC=3.3V, IO=250mA Minimum dropout voltage2 VCO2 - 0.20 0.30 V VCC=3.3V, IO=500mA Minimum dropout voltage3 VCO3 - 0.30 0.45 V VCC=3.3V, IO=750mA Minimum dropout voltage4 VCO4 - 0.40 0.60 V VCC=3.3V, IO=1.0A Output reference voltage(variable type) VFB 0.792 0.800 0.808 V IO=0A Output voltage(Fixed type) VO Vox0.99 Vo Vox1.01 V IO=0A EN Low voltage VEN_Low 0 - 0.8 V EN High voltage VEN_High 2.4 - 5.5 V EN Bias current IEN 1 3 9 A www.rohm.com (c) 2015 ROHM Co., Ltd. All rights reserved. TSZ2211115001 5/23 TSZ02201-GAG0A600030-1-2 19.Aug.2015 Rev.004 Datasheet BDxxIC0WEFJ / BDxxIC0WHFV Typical Performance Curves (Unless otherwise noted, Ta=25, EN=3V, VCC=3.3V, R1=16k, R2=7.5k) VVV OOO VOO IIOOIO IOO Fig.4 Transient Response(1.00A) Co=1.0F Fig.3 Transient Response(01.0A) Co=1.0F VEN VEN VCC VCC VO VO Fig.5 Input sequence1 Co=1.0F www.rohm.com (c) 2015 ROHM Co., Ltd. All rights reserved. TSZ2211115001 Fig.6 OFF sequence 1 Co=1.0F 6/23 TSZ02201-GAG0A600030-1-2 19.Aug.2015 Rev.004 Datasheet BDxxIC0WEFJ / BDxxIC0WHFV VEN VEN VCC VCC VO VO Fig.8 OFF sequence 2 Co=1.0F VO[V] VFB[V] Fig.7 Input sequence2 Co=1.0F Ta[] Ta[] Fig.10 Ta-VO (IO=0A) Fig.9 Ta-VFB www.rohm.com (c) 2015 ROHM Co., Ltd. All rights reserved. TSZ2211115001 7/23 TSZ02201-GAG0A600030-1-2 19.Aug.2015 Rev.004 Datasheet ICC[A] ISTB[A] BDxxIC0WEFJ / BDxxIC0WHFV Ta[] Ta[] Fig.11 Ta-ICC ISTB[A] IEN[A] Fig.12 Ta-ISTB (VEN=0V) Ta[] VCC[V] Fig.14 Ta-IEN Fig.13 VCC-ISTB (VEN=0V) www.rohm.com (c) 2015 ROHM Co., Ltd. All rights reserved. TSZ2211115001 8/23 TSZ02201-GAG0A600030-1-2 19.Aug.2015 Rev.004 Datasheet VO[V] VO[V] BDxxIC0WEFJ / BDxxIC0WHFV IO[A] IO[A] Fig.16 IO-VO (VO=1.5V) VO[V] VO[V] Fig.15 IO-VO (VO=1.2V) IO[A] IO[A] Fig.18 IO-VO (VO=2.5V) Fig.17 IO-VO (VO=1.8V) www.rohm.com (c) 2015 ROHM Co., Ltd. All rights reserved. TSZ2211115001 9/23 TSZ02201-GAG0A600030-1-2 19.Aug.2015 Rev.004 Datasheet VO[V] VO[V] BDxxIC0WEFJ / BDxxIC0WHFV IO[A] VCC[V] Fig.20 VCC-VO (IO=0A) VO[V] VO[V] Fig.19 IO-VO (VO=3.3V) Ta[] IO[A] Fig.21 TSD (IO=0A) Fig.22 OCP (VCC=5V, VO=3.3V) www.rohm.com (c) 2015 ROHM Co., Ltd. All rights reserved. TSZ2211115001 10/23 TSZ02201-GAG0A600030-1-2 19.Aug.2015 Rev.004 Datasheet VO[V] VO[V] BDxxIC0WEFJ / BDxxIC0WHFV Fig.23 OCP (VCC=5V, VO=2.5V) Fig.24 OCP (VCC=5V, VO=1.8V) VO[V] IO[A] VO[V] IO[A] IO[A] IO[A] Fig.25 OCP (VCC=5V, VO=1.5 V) Fig.26 OCP (VCC=5V, VO=1.2 V) www.rohm.com (c) 2015 ROHM Co., Ltd. All rights reserved. TSZ2211115001 11/23 TSZ02201-GAG0A600030-1-2 19.Aug.2015 Rev.004 Datasheet VO[V] VO[V] BDxxIC0WEFJ / BDxxIC0WHFV IO[A] Fig.27 OCP (VCC=3.3V, VO=2.5V) Fig.28 OCP (VCC=3.3V, VO=1.8V) VO[V] VO[V] IO[A] IO[A] IO[A] Fig.29 OCP (VCC=3.3V, VO=1.5 V) Fig.30 OCP (VCC=3.3V, VO=1.2 V) www.rohm.com (c) 2015 ROHM Co., Ltd. All rights reserved. TSZ2211115001 12/23 TSZ02201-GAG0A600030-1-2 19.Aug.2015 Rev.004 Datasheet BDxxIC0WEFJ / BDxxIC0WHFV IO[A] Fig.31 ESR-IO characteristics (Co=2.2F) Fig.32 IO-ICC Vdrop[V] IO[A] Ta[] Fig.34 Minimum dropout Voltage 1 (VCC=3.3V, IO=1.0A) Fig.33 PSRR(IO=0A) www.rohm.com (c) 2015 ROHM Co., Ltd. All rights reserved. TSZ2211115001 13/23 TSZ02201-GAG0A600030-1-2 19.Aug.2015 Rev.004 Datasheet BDxxIC0WEFJ / BDxxIC0WHFV IO[A] IO[A] Fig.35 Minimum dropout Voltage2 (VCC=2.4V) Fig.36 Minimum dropout Voltage3 (VCC=3.3V) IO[A] Fig.37 Minimum dropout Voltage4 (VCC=5.0V) www.rohm.com (c) 2015 ROHM Co., Ltd. All rights reserved. TSZ2211115001 14/23 TSZ02201-GAG0A600030-1-2 19.Aug.2015 Rev.004 Datasheet BDxxIC0WEFJ / BDxxIC0WHFV Power Dissipation HTSOP-J8 4.0 Power Dissipation :Pd [W] 3.76W Measurement condition: mounted on a ROHM board, Substrate size: 70mm x 70mm x 1.6mm (Substrate with thermal via) Solder the thermal pad to Ground 3.0 IC only j-a=249.5/W 1-layercopper foil are :0mmx0mm j-a=153.2/W 2-layercopper foil are :15mmx15mm j-a=113.6/W 2-layercopper foil are :70mmx70mm j-a=59.2/W 4-layercopper foil are :70mmx70mm j-a=33.3/W 2.11W 2.0 1.10W 1.0 0.82W 0.50W 0 0 25 50 75 100 125 150 Ambient :Ta Temperature [] :Ta [] HVSOF6 Power Dissipation: Pd [W] 4.0 Measurement condition: mounted on a ROHM board, Substrate size: 70mm x 70mm x 1.6mm (Substrate with thermal via) Solder the thermal pad to Ground 3.0 single-layer(copper foil are :2%) j-a=147.1/W single-layer(copper foil are :18%) j-a=89.3/W single-layer(copper foil are :51%) j-a=73.5/W 2.0 1.7W 1.4W 1.0 0.85W 0.0 0 25 50 75 100 Ambient Temperature: Ta [] www.rohm.com (c) 2015 ROHM Co., Ltd. All rights reserved. TSZ2211115001 125 15/23 150 TSZ02201-GAG0A600030-1-2 19.Aug.2015 Rev.004 Datasheet BDxxIC0WEFJ / BDxxIC0WHFV Thermal design should ensure operation within the following conditions. Note that the temperatures listed are the allowed temperature limits and thermal design should allow sufficient margin beyond these limits. 1. Ambient temperature Ta can be no higher than 85. 2. Chip junction temperature (Tj) can be no higher than 150. Chip junction temperature can be determined as follows: Calculation based on ambient temperature (Ta) Tj=Ta+j-axP Reference values j-aHTSOP-J8 153.2/W 113.6/W 59.2/W 33.3/W 1-layer substrate (copper foil density 0mmx0mm) 2-layer substrate (copper foil density 15mmx15mm) 2-layer substrate (copper foil density 70mmx70mm) 4-layer substrate (copper foil density 70mmx70mm) Substrate size: 70mmx70mmx1.6mm (substrate with thermal via) Most of the heat loss that occurs in the BDxxIC0W series is generated from the output Pch FET. Power loss is determined by the total VCC-VO voltage and output current. Be sure to confirm the system input and output voltage as well as the output current conditions in relation to the heat dissipation characteristics of the VCC and VO in the design. Bearing in mind that heat dissipation may vary substantially depending on the substrate employed (due to the power package incorporated in the BDxxIC0W series )make certain to factor conditions such as substrate size into the thermal design. Power consumption [W] = Input voltage (VCC) - Output voltage (VO) xIO(Ave) Example) When VCC=3.3V, VO=2.5V, IO(Ave) = 0.1A Power consumption [W] = 3.3V - 2.5V x0.1A =0.08[W] www.rohm.com (c) 2015 ROHM Co., Ltd. All rights reserved. TSZ2211115001 16/23 TSZ02201-GAG0A600030-1-2 19.Aug.2015 Rev.004 Datasheet BDxxIC0WEFJ / BDxxIC0WHFV Input-to-Output Capacitor It is recommended that a capacitor (over 1uF) is placed near pins between the input pin and GND as well as the output pin and GND. A capacitor, between input pin and GND, is valid when the power supply impedance is high or trace is long. Also, as for the capacitor between the output pin and GND, the greater the capacitance, the more sustainable the line regulation will be and the capacitor will make improvements of characteristics depending on the load. However, please check the actual functionality of this part by mounting it on a board for the actual application. Ceramic capacitors usually have different, thermal and equivalent series resistance characteristics, and moreover capacitance decreases gradually in use. For additional details, please check with the manufacturer, and select the best ceramic capacitor for your application. 10 Rated Voltage10V B1 characteristics Rated Voltage10V B characteristics 0 Capacitance Change [%] -10 Rated Voltage6.3V B characteristics -20 -30 -40 -50 Rated Voltage:10V F characteristics -60 Rated Voltage4V X6S characteristics -70 -80 -90 -100 0 1 2 3 4 DC Bias Voltage [V] Ceramic capacitor capacity - DC bias characteristics (Characteristics example) Equivalent Series Resistance ESR (Output Capacitor) 10.00 1.00 ESR [] To prevent oscillations, please attach a capacitor between VO and GND. Capacitors usually have ESR (Equivalent Series Resistance). Operation will be stable in the ESR-IO range shown to the right. This reference data condition is 1.0uF Ceramic capacitor and resistor are connected to output in series. Ceramic, tantalum and electrolytic Capacitors have different ESR values, so please ensure that you are using a capacitor that operates in the stable operating region shown on the right. Finally, please evaluate in the actual application. Safety area 0.10 COUT=1uF 0.01 0 0.2 0.4 0.6 Io [A] 0.8 1 ESR - IO characteristics www.rohm.com (c) 2015 ROHM Co., Ltd. All rights reserved. TSZ2211115001 17/23 TSZ02201-GAG0A600030-1-2 19.Aug.2015 Rev.004 Datasheet BDxxIC0WEFJ / BDxxIC0WHFV Evaluation Board Circuit U1 C3 C7 1 VCC VO 8 C2 C6 R1 C5 2 FB N.C 7 GND N.C 6 C1 R2 GND 3 SW1 VO 4 N.C. EN EN 5 FIN Evaluation Board Parts List Designation Value Part No. Company Designation Value Part No. Company R1 16k MCR01PZPZF1602 ROHM C4 R2 7.5k MCR01PZPZF7501 ROHM C5 1F CM105B105K10A KYOCERA R3 C6 R4 C7 R5 C8 R6 C9 C1 1F CM105B105K16A KYOCERA C10 C2 U1 BD00IC0WEFJ ROHM C3 U2 Board Layout EN GND CIN VCC ( VIN ) R1 R2 COUT VO PCB layout considerations: Input capacitor CIN connected to VCC (Vin) should be placed as close to VCC(VIN) pin as possible. Output capacitor COUT also should be placed as close to IC pin as possible. In case the part is connected to inner layer GND plane, please use several through holes. FB pin has comparatively high impedance and can be affected by noise, so stray capacitance should be as small as possible. Please take care of this during layout. Please make GND pattern wide enough to handle thermal dissipation. For output voltage setting Output voltage can be set by FB pin voltage (0.800V typ.) and external resistance R1, R2. R1+R2 VO = VFBx R2 (The use of resistors with R1+R2=1k to 90k is recommended) www.rohm.com (c) 2015 ROHM Co., Ltd. All rights reserved. TSZ2211115001 18/23 TSZ02201-GAG0A600030-1-2 19.Aug.2015 Rev.004 Datasheet BDxxIC0WEFJ / BDxxIC0WHFV I/O Equivalent Circuits (Variable typeBD00IC0WEFJ) 8pin(VCC) / 1pin(VO) 8pin(VCC) 2pin(FB) 5pin(EN) 2pin(FB) 5pin (EN ) 520k 1pn(VO) 480k I/O Equivalent Circuits (Fixed typeBDxxIC0WEFJ) 8pin(VCC) / 1pin(VO) 2pin(VO_S) 5pin(EN) 8pin(VCC) 2pin(VO_S) 5pin(EN) 520k 480k 1pin(VO) I/O Equivalent Circuits (Variable typeBD00IC0WHFV) 6pin(VCC) / 1pin(VO) 2pin(FB) 4pin(EN) 6pin(VCC) 2pin(FB) 4pin (EN ) 520k 1pn(VO) 480k I/O Equivalent Circuits (Fixed typeBDxxIC0WHFV) 6pin(VCC) / 1pin(VO) 2pin(VO_S) 4pin(EN) 6pin(VCC) 2pin(VO_S) 4pin(EN) 480k 1pin(VO) www.rohm.com (c) 2015 ROHM Co., Ltd. All rights reserved. TSZ2211115001 520k 19/23 TSZ02201-GAG0A600030-1-2 19.Aug.2015 Rev.004 Datasheet BDxxIC0WEFJ / BDxxIC0WHFV Operational Notes (1) Absolute maximum ratings An excess in the absolute maximum ratings, such as supply voltage, temperature range of operating conditions, etc., can break down the device, thus making it impossible to identify the damage mode, such as a short circuit or an open circuit. If there is any possibility of exposure over the rated values, please consider adding circuit protection devices such as fuses. (2) Connecting the power supply connector backward Connecting of the power supply in reverse polarity can damage the IC. Take precautions when connecting the power supply lines. An external direction diode can be added. (3) Power supply lines Design the PCB layout pattern to provide low impedance GND and supply lines. To obtain a low noise ground and supply line, separate the ground section and supply lines of the digital and analog blocks. Furthermore, for all power supply terminals to ICs, connect a capacitor between the power supply and GND terminal. When using electrolytic capacitors in a circuit, note that capacitance values are reduced at low temperatures and over time. (4) GND voltage The potential of the GND pin must be minimum potential under all operating conditions. (5) Thermal design Use a thermal design that allows for a sufficient margin in light of the power dissipation (Pd) in actual operating conditions. (6) Off-leakage at high temperature. Off-leakage at high temperature may increase because of manufacturing variations. Design should consider the typical & worst cases shown below. Ta-Ileak 0.5 0.4 Ileak (mA) worst 0.3 0.2 0.1 typ 0 25 50 75 100 Temperature () 125 150 (7) Inter-pin shorts and mounting errors Use caution when positioning the IC for mounting on printed circuit boards. The IC may be damaged if there is any connection error or if pins are shorted together. (8) Actions in strong electromagnetic field Use caution when using the IC in the presence of a strong electromagnetic field as doing so may cause the IC to malfunction. (9) ASO When using the IC, set the output transistor so that it does not exceed absolute maximum ratings or ASO. (10) Thermal shutdown circuit The IC incorporates a built-in thermal shutdown circuit (TSD circuit). The thermal shutdown circuit (TSD circuit) is designed only to shut the IC off to prevent thermal runaway. It is not designed to protect the IC or guarantee its operation. Do not continue to use the IC after operating this circuit or use the IC in an environment where the operation of this circuit is assumed. TSD ON Temperature[] (typ.) BDxxIC0W series www.rohm.com (c) 2015 ROHM Co., Ltd. All rights reserved. TSZ2211115001 175 Hysteresis Temperature [] (typ.) 15 20/23 TSZ02201-GAG0A600030-1-2 19.Aug.2015 Rev.004 Datasheet BDxxIC0WEFJ / BDxxIC0WHFV (11)Testing on application boards When testing the IC on an application board, connecting a capacitor to a pin with low impedance subjects the IC to stress. Always discharge capacitors after each process or step. Always turn the IC's power supply off before connecting it to or removing it from a jig or fixture during the inspection process. Ground the IC during assembly steps as an antistatic measure. Use similar precaution when transporting or storing the IC. (12) Regarding input pin of the IC This monolithic IC contains P+ isolation and P substrate layers between adjacent elements in order to keep them isolated. P-N junctions are formed at the intersection of these P layers with the N layers of other elements, creating a parasitic diode or transistor. For example, the relation between each potential is as follows: When GND > Pin A and GND > Pin B, the P-N junction operates as a parasitic diode. When GND > Pin B, the P-N junction operates as a parasitic transistor. Parasitic diodes can occur inevitable in the structure of the IC. The operation of parasitic diodes can result in mutual interference among circuits, operational faults, or physical damage. Accordingly, methods by which parasitic diodes operate, such as applying a voltage that is lower than the GND (P substrate) voltage to an input pin, should not be used. Resistor Transistor (NPN) Pin A Pin B C Pin B B E Pin A N P+ N P P+ N N Parasitic element P+ GND B P P+ C N E P substrate Parasitic element N P substrate Parasitic element GND GND Parasitic element Other adjacent elements GND (13) Ground Wiring Pattern. When using both small signal and large current GND patterns, it is recommended to isolate the two ground patterns, placing a single ground point at the ground potential of application so that the pattern wiring resistance and voltage variations caused by large currents do not cause variations in the small signal ground voltage. Be careful not to change the GND wiring pattern of any external components, either. www.rohm.com (c) 2015 ROHM Co., Ltd. All rights reserved. TSZ2211115001 21/23 TSZ02201-GAG0A600030-1-2 19.Aug.2015 Rev.004 Datasheet BDxxIC0WEFJ / BDxxIC0WHFV Physical Dimension Tape and Reel Information HTSOP-J8 <Tape and Reel information> 4 (2.4) 3.90.1 6.00.2 8 7 6 5 +6 -4 1 0.650.15 (3.2) 1.050.2 4.90.1 (MAX 5.25 include BURR) Tape Embossed carrier tape Quantity 2500pcs E2 Direction of feed The direction is the 1pin of product is at the upper left when you hold ( reel on the left hand and you pull out the tape on the right hand ) 2 3 4 1PIN MARK +0.05 0.17 -0.03 1.0MAX 0.545 S +0.05 0.42 -0.04 0.080.08 0.850.05 1.27 0.08 M 0.08 S Direction of feed 1pin Reel (Unit : mm) Order quantity needs to be multiple of the minimum quantity. HVSOF6 <Tape and Reel information> (1.5) (0.45) 6 5 4 Tape Embossed carrier tape Quantity 3000pcs TR Direction of feed The direction is the 1pin of product is at the upper right when you hold ( reel on the left hand and you pull out the tape on the right hand (1.4) 1 2 3 (0.15) (1.2) ) 1pin 0.1450.05 0.75Max. 3.00.1 2.60.1 (MAX 2.8 include BURR) 1.60.1 (MAX 1.8 include BURR) S 0.1 S 0.220.05 Direction of feed 0.5 Reel (Unit : mm) Order quantity needs to be multiple of the minimum quantity. Marking Diagram HTSOP-J8(TOP VIEW) Part Number Marking x x I C 0 W LOT Number 1PIN MARK HVSOF6(TOP VIEW) Part Number Marking xx LOT Number 1PIN MARK www.rohm.com (c) 2015 ROHM Co., Ltd. All rights reserved. TSZ2211115001 22/23 xx 00 10 12 15 18 25 30 33 Product Name BD00IC0WEFJ BD10IC0WEFJ BD12IC0WEFJ BD15IC0WEFJ BD18IC0WEFJ BD25IC0WEFJ BD30IC0WEFJ BD33IC0WEFJ xx B0 BT BU BS BV BW BX BR BY BZ Product Name BD00IC0WHFV BD10IC0WHFV BD12IC0WHFV BD1CIC0WHFV BD15IC0WHFV BD18IC0WHFV BD25IC0WHFV BD26IC0WHFV BD30IC0WHFV BD33IC0WHFV TSZ02201-GAG0A600030-1-2 19.Aug.2015 Rev.004 Datasheet BDxxIC0WEFJ / BDxxIC0WHFV Revision History Date Revision 6.Jul.2012 21.Dec.2012 24.Sep.2014 19.Aug.2015 001 002 003 004 Changes New Release. The description was modified. The power dissipation data was added. P5 modify Absolute Maximum Ratings (Power supply voltage and EN voltage) www.rohm.com (c) 2015 ROHM Co., Ltd. All rights reserved. TSZ2211115001 23/23 TSZ02201-GAG0A600030-1-2 19.Aug.2015 Rev.004 Datasheet Notice Precaution on using ROHM Products 1. Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment, OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you (Note 1) , transport intend to use our Products in devices requiring extremely high reliability (such as medical equipment equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property ("Specific Applications"), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM's Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASS CLASSb CLASS CLASS CLASS CLASS 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM's Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual ambient temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification Notice-PGA-E (c) 2015 ROHM Co., Ltd. All rights reserved. Rev.001 Datasheet Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label QR code printed on ROHM Products label is for ROHM's internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign trade act, please consult with ROHM in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. 2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the Products with other articles such as components, circuits, systems or external equipment (including software). 3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to manufacture or sell products containing the Products, subject to the terms and conditions herein. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. Notice-PGA-E (c) 2015 ROHM Co., Ltd. All rights reserved. Rev.001 Datasheet General Precaution 1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents. ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny ROHM's Products against warning, caution or note contained in this document. 2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior notice. Before purchasing or using ROHM's Products, please confirm the la test information with a ROHM sale s representative. 3. The information contained in this doc ument is provi ded on an "as is" basis and ROHM does not warrant that all information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information. Notice - WE (c) 2015 ROHM Co., Ltd. All rights reserved. Rev.001 Datasheet bd00ic0wefj - Web Page Buy Distribution Inventory Part Number Package Unit Quantity Minimum Package Quantity Packing Type Constitution Materials List RoHS bd00ic0wefj HTSOP-J8 2500 2500 Taping inquiry Yes