Thermofit Molded Parts Adhesives Applications Thermofit adhesives are intended to provide an environmental seal when used with Thermofit molded parts, tubing, and adapters, and when installed in accordance with installation procedures. 3 Thermosets Product designation S-1006 Precoat designation N/A S-1009 N/A S-1010 N/A S-1044 N/A S-1125 N/A Type Epoxy/ polyamide 2-part paste Epoxy/ polymercaptan 2-part paste VITON cement 2-part liquid VITON tape adhesive Epoxy/ polyamide 2-part paste Operating temperature range -55 to 135C Available form S-1006 Kit A S-1006 Kit C Ten 3-g packs Six 2-oz semkits -55 to 135C S-1009 Kit A Ten 3-g packs 1-qt part B -55 to 200C S-1010 -55 to 200C S-1044-03 S-1044 Primer S-1125 Kit 1 S-1125 Kit 3 1/2-pint can with accelerator Tape 3/4" x .018" x 100' 1/2-pint can Five 10-g packs One 100-g pack -55 to 135C Thermosets Curing conditions 96 hrs @ 20C min. or 1 hr @ 120C 24 hrs @ 20C min. or 1 hr @ 95C or 45 mins @ 120C 2 hrs @ 150C min. or 20 mins @ 200C 2 hrs. @ 150C min. or 20 mins @ 200C 24 hrs @ 20C min. or *Shelf life from date of manufacture. 3-42 Shelf life* at or below 25C 2 years Compatible with material -3, -4, -5, -71 2 years -3, -4, -5, -71 1 year -12 RT-1050/10 Tape: 1 year Primer: 1 year -12 -12 RT-1050/22 RT-1050/14 18 months -12, -25 RT-1011 Specifications RT-1006 MIL-A-46864 RT-1009 MIL-A-46864 Comments General purpose harnessing adhesive. Not used on VITON, silicone, or substrates. General purpose harnessing adhesive. Not used on VITON or silicone-20 minute pot life. Used with VITON. Heat cure required. Self-amalgamating tape used with VITON harness systems. All surfaces should be primed with S-1044 primer. Heat cure required: 2 hrs @ 150C. Good fluid-resistant epoxy used with System 25. Thermoplastics Product designation S-1017 Precoat designation /42 S-1030 /180 S-1048 /86 Type Hot melt/ polyamide Hot melt/ polyolefin Hot melt high performance Operating temperature range -20 to 60C Available form S-1017 Tape 1" x .010" x 50' -80 to 80C S-1030 Tape 3/4" x .010" x 33' -55 to 120C S-1048 Tape 1" x .026" x 100' Thermoplastics 3 Bonding temperature minimum 120C Shelf life at or below 25C Unlimited Compatible with material -3, -4, -25, -71 Specifications RT-1050/1 120C Unlimited -3, -4, -71 RT-1050/6 160C Unlimited -3, -4, -25, -71 RT-1050/3 Comments General purpose harnessing adhesive. Standard precoated adhesive for -3 and -4 molded parts. Good low-temperature flexibility. Available as a preinstalled tape for molded parts. Requires higher temperature to achieve bonding. Highest service temperature for hot melt. Ordering Information Thermosets can be ordered by the designated "S" number and kit size (for example, S-1006-KIT-C). To receive the tape form, order the thermoplastics by their "S" number. They may be precoated on a molded part when the optional adhesive coating is included in the part number (see page 3-3). Thermofit is a registered trademark of Raychem Corporation. VITON is a registered trademark of E. I. du Pont de Nemours & Co., Inc. 3-43