Product Specification 10km Duplex SMF 100G CFP4 Optical Transceiver FTLC1141RDNL PRODUCT FEATURES Hot-pluggable CFP4 form factor Supports 103.1Gb/s aggregate bit rate Power dissipation < 5W RoHS compliant Commercial case temperature range of 0C to 75C Single 3.3V power supply Maximum link length of 10km on Single Mode Fiber (SMF) APPLICATIONS 4x25Gb/s DFB-based LAN-WDM transmitter 4x25G electrical interface Duplex LC receptacles MDIO management interface 100GBASE-LR4 100G Ethernet Finisar's FTLC1141RDNL 100G CFP4 transceiver modules are designed for use in 100 Gigabit Ethernet interfaces over single mode fiber. They are compliant with the CFP MSA1, IEEE 802.3ba 100GBASE-LR42 and IEEE 802.3bm CAUI-45. Digital diagnostics functions are available via the MDIO interface, as specified by the CFP MSA and Finisar Application Note AN-20xx4. The transceiver is RoHS compliant per Directive 2011/65/EU3. PRODUCT SELECTION FTLC1141RDxL R: D: x: L: Finisar Corporation - 20-June-2016 100G Ethernet maximum bit rate (103.1 Gb/s) 4x25G LAN-WDM optics N: Bail type release | P: Pull Tab LC receptacles Rev. C1 Page 1 FTLC1141RDNL Product Specification - June 2016 I. Pin Descriptions Per CFP MSA1. Pins views from the top. 56 55 Top Row GND TX3n 1 2 Bottom Row 3.3V_GND 3.3V_GND 54 TX3p 3 3.3V 53 GND 4 3.3V 52 TX2n 5 3.3V 51 TX2p 6 3.3V 50 GND 7 3.3V_GND 49 TX1n 8 3.3V_GND 48 TX1p 9 VND_IO_A 47 GND 10 VND_IO_B 46 TX0n 11 TX_DIS 45 TX0p 12 RX_LOS 44 GND 13 GLB_ALRMn 43 {REFCLKn} 14 MOD_LOPWR 42 {REFCLKp} 15 MOD_ABS 41 GND 16 MOD_RSTn 40 RX3n 17 MDC 39 RX3p 18 MDIO 38 GND 19 PRTADR0 37 RX2n 20 PRTADR1 36 RX2p 21 PRTADR2 35 GND 22 VND_IO_C 34 RX1n 23 VND_IO_D 33 RX1p 24 VND_IO_E 32 GND 25 GND 31 RX0n 26 {MCLKn} 30 RX0p 27 {MCLKp} 29 GND 28 GND Finisar Corporation - 20-June-2016 Rev. C1 Page 2 FTLC1141RDNL Product Specification - June 2016 Bottom Row Pin Descriptions PIN # 1 2 3 4 5 6 7 8 9 10 11 12 3.3V_GND 3.3V_GND 3.3V 3.3V 3.3V 3.3V 3.3V_GND 3.3V_GND VND_IO_A VND_IO_B TX_DIS RX_LOS I/O I/O I O 13 GLB_ALRMn O 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 MOD_LOPWR MOD_ABS MOD_RSTn MDC MDIO PRTADR0 PRTADR1 PRTADR2 VND_IO_C VND_IO_D VND_IO_E GND MCLKn MCLKp GND I O I I/O I I I I I/O I/O I/O Name I/O Logic Description 3.3V Module Supply Voltage Return Ground, internally connected to Signal Ground 3.3V Module Supply Voltage Return Ground, internally connected to Signal Ground 3.3V Module Supply Voltage 3.3V Module Supply Voltage 3.3V Module Supply Voltage 3.3V Module Supply Voltage 3.3V Module Supply Voltage Return Ground, internally connected to Signal Ground 3.3V Module Supply Voltage Return Ground, internally connected to Signal Ground Module Vendor I/O A. Do Not Connect! Module Vendor I/O B. Do Not Connect! LVCMOS w/ PUR Transmitter Disable for all lanes, "1" or NC = transmitter disabled, "0" = transmitter enabled LVCMOS Receiver Loss of Optical Signal, "1": low optical signal, "0": normal condition Global Alarm. "0": alarm condition in any MDIO Alarm register, "1": no alarm condition, Open Drain, LVCMOS Pull Up Resistor on Host LVCMOS w/ PUR Module Low Power Mode. "1" or NC: module in low power (safe) mode, "0": power-on enabled GND Module Absent. "1" or NC: module absent, "0": module present, Pull Up Resistor on Host LVCMOS w/ PDR Module Reset. "0" resets the module, "1" or NC = module enabled, Pull Down Resistor in Module 1.2V CMOS Management Data I/O bi-directional data (electrical specs as per 802.3ae and ba) 1.2V CMOS Management Data Clock (electrical specs as per 802.3ae and ba) 1.2V CMOS MDIO Physical Port address bit 0 1.2V CMOS MDIO Physical Port address bit 1 1.2V CMOS MDIO Physical Port address bit 2 Module Vendor I/O C. Do Not Connect! Module Vendor I/O D. Do Not Connect! Module Vendor I/O E. Do Not Connect! Monitor Clock - Support is TBD Monitor Clock - Support is TBD Finisar Corporation - 20-June-2016 Rev. C1 Page 3 FTLC1141RDNL Product Specification - June 2016 II. Absolute Maximum Ratings Module performance is not guaranteed beyond the operating range (see Section VI). Exceeding the limits below may damage the transceiver module permanently. Parameter Maximum Supply Voltage Storage Temperature Case Operating Temperature Relative Humidity Receiver Damage Threshold, per Lane Symbol Vcc TS TOP RH PRdmg Min -0.5 -40 0 15 5.5 Typ Max 4.0 85 75 85 Unit V C C % dBm Ref. Ref. 25.78 Unit V A W Gb/s 900 mV 1 2 Notes: 1. 48-hour excursions, maximum 2. Non-condensing. III. Electrical Characteristics (EOL, TOP = 0 to 75 C, VCC = 3.2 to 3.4 Volts) Parameter Supply Voltage Supply Current Module total power Transmitter Signaling rate per lane Differential pk-pk input voltage tolerance Single-ended voltage tolerance Module stress input test Receiver Signaling rate per lane Differential output voltage Eye width Eye height, differential Vertical eye closure Transition time (20% to 80%) Symbol Vcc Icc P Min 3.2 Typ Vin,pp,diff Vin,pp -0.4 +3.3 Per Section 83E.3.4.1, IEEE 802.3bm 25.78 900 Vout,pp VEC tr, tf Max 3.4 1.9 5 0.57 228 5.5 12 1 2 V Gb/s mV UI mV dB ps 2 Notes: 1. Maximum total power value is specified across the full temperature and voltage range. 2. +/- 100ppm FTLC1141RDNL Clocking Signals Clock Name Status I/O Value REFCLK Not Required I N/A (terminated internally) MCLK Supported O 1/8 of host lane rate Finisar Corporation - 20-June-2016 Rev. C1 Page 4 FTLC1141RDNL Product Specification - June 2016 IV. Optical Characteristics (EOL, TOP = 0 to 75C, VCC = 3.2 to 3.4 Volts) Parameter Transmitter Signaling Speed per Lane Lane center wavelengths (range) Symbol Total Average Launch Power Transmit OMA per Lane Average Launch Power per Lane Optical Extinction Ratio Sidemode Suppression ratio Average launch power of OFF transmitter, per lane Relative Intensity Noise Optical Return Loss Tolerance Transmitter Reflectance Transmitter eye mask definition {X1, X2, X3, Y1, Y2, Y3} Receiver Signaling Speed per Lane Lane center wavelengths (range) POUT TxOMA TXPx ER SSRmin Min Typ 25.78 Max 25.78 1294.53 - 1296.59 1299.02 - 1301.09 1303.54 - 1305.63 1308.09 - 1310.19 10.5 4.5 4.5 -1.3 -4.3 4 30 RIN Unit Gb/s nm -30 dBm dBm dBm dB dB dBm -130 20 -12 dB/Hz dB dB Ref. 1 2 {0.25, 0.4, 0.45, 0.25, 0.28, 0.4} 25.78 25.78 1294.53 - 1296.59 1299.02 - 1301.09 1303.54 - 1305.63 1308.09 - 1310.19 GBd nm 3 Receive Power (OMA) per Lane RxOMA 4.5 dBm Average Receive Power per Lane RXPx -10.6 4.5 dBm 4 Receiver Sensitivity (OMA) per Lane Rxsens -8.6 dBm Stressed Receiver Sensitivity (OMA) SRS -6.8 dBm per Lane Return Loss RL -26 dB Vertical eye closure penalty, per lane 1.8 dB Receive electrical 3 dB upper cutoff 31 GHz frequency, per lane LOS De-Assert LOSD -11.6 dBm LOS Assert LOSA -13.6 dBm LOS Hysteresis 1 dBm Notes: 1. Transmitter consists of 4 lasers operating at 25.78Gb/s each. 2. Minimum value is informative. 3. Receiver consists of 4 photodetectors operating at 25.78Gb/s each. 4. Minimum value is informative, equals min TxOMA with infinite ER and max channel insertion loss. Finisar Corporation - 20-June-2016 Rev. C1 Page 5 FTLC1141RDNL Product Specification - June 2016 V. General Specifications Parameter Symbol Bit Rate (all wavelengths combined) BR Bit Error Ratio @25.78Gb/s BER1 Maximum Supported Distances Fiber Type SMF per G.652 Lmax1 Notes: 1. Supports 100GBASE-LR4 per IEEE 802.3ba. 2. Tested with a 231 - 1 PRBS. VI. Min Typ Max 103.1 10-12 Units Gb/s 10 km Ref. 1 2 Environmental Specifications Finisar FTLC1141 CFP4 transceivers have a commercial operating case temperature range of 0C to +75C. Parameter Case Operating Temperature Storage Temperature VII. Symbol Top Tsto Min 0 -40 Typ Max 75 85 Units C C Ref. Regulatory Compliance Finisar FTLC1141 CFP4 transceivers are Class 1 Laser Products. They are certified per the following standards: Feature Agency Standard Laser Eye Safety Laser Eye Safety Electrical Safety Electrical Safety FDA/CDRH CDRH 21 CFR 1040 and Laser Notice 50 TUV EN 60825-1: 2007 IEC 60825-2: 2004+A1+A2 EN 60950 R72130387 CLASS 3862.07 CLASS 3862.87 1909932375840 TUV UL/CSA Certificate Number 9210176 R72130387 Copies of the referenced certificates are available at Finisar Corporation upon request. Complies with FDA performance standards for laser products except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007. Finisar Corporation - 20-June-2016 Rev. C1 Page 6 FTLC1141RDNL Product Specification - June 2016 VIII. Digital Diagnostics Functions FTLC1141 CFP4 transceivers support the MDIO-based diagnostics interface specified in the CFP MSA1. See Finisar Application Note AN-20xx (TBD). IX. Memory Contents Per the CFP MSA1. See Finisar Application Note AN-20xx (TBD). X. Host PCB Layout and Bezel Recommendations Per CFP MSA Hardware Specification for CFP41. Finisar Corporation - 20-June-2016 Rev. C1 Page 7 FTLC1141RDNL Product Specification - June 2016 XI. Mechanical Specifications Finisar FTLC1141 CFP4 transceivers are compatible with the CFP MSA specification for CFP4 pluggable form factor modules. Figure 1. FTLC1141RDNL Mechanical Dimensions. Finisar Corporation - 20-June-2016 Rev. C1 Page 8 FTLC1141RDNL Product Specification - June 2016 Figure 2. Standard Product Label XII. References 1. CFP4 Hardware Specification and CFP MSA Management Interface Specifications (MIS), Rev 2.4.; CFP MSA, www.cfp-msa.org 2. IEEE 802.3ba, PMD Type 100GBASE-LR4. 3. Directive 2011/65/EU of the European Council Parliament and of the Council, "on the restriction of the use of certain hazardous substances in electrical and electronic equipment," June 8, 2011. 4. Application Note AN-20xx (TBD), Finisar Corporation. 5. IEEE 802.3bm, Annex 83E, CAUI-4 Interface. For More Information: Finisar Corporation 1389 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 sales@finisar.com www.finisar.com Finisar Corporation - 20-June-2016 Rev. C1 Page 9