SMDA03C-8 8700 E. Thomas Road Scottsdale, AZ 85251 Tel: (480) 941-6300 Fax: (480) 947-1503 thru SMDA24C-8 TVSarray Series DESCRIPTION (300 watt) This 14 pin 8 line Bi-directional array is designed for use in applications where protection is required at the board level from voltage transients caused by electrostatic discharge (ESD) as defined in IEC 1000-4-2, electrical fast transients (EFT) per IEC 1000-4-4 and effects of secondary lighting. These TRANSIENT VOLTAGE SUPPRESSOR (TVS) Diode Arrays have a peak power of 300 watts for an 8/20 sec pulse and are designed to protect 3.0/3.3 volt components such as DRAM's, SRAM's, CMOS, HCMOS, HSIC, and low voltage interfaces up to 24 volts. FEATURES MECHANICAL * * * * * * * * * Protects 3.0/3.3 up through 24V Components Protects 8 lines Bi-directional Provides electrically isolated protection SO-14 Packaging Molded SO-14 Surface Mount Weight: 0.127 grams (approximate) Body Marked with Logo, and device number Pin #1 defined by DOT on top of package Encapsulation meets UL 94V-0 MAXIMUM RATINGS PACKAGING * * * * * * * Operating Temperatures: -550 C to +1500 C Storage Temperature: -550 C to +1500 C Peak Pulse Power: 300 Watts (8/20 sec, Figure 1) Pulse Repetition Rate: <.01% Tape & Reel EIA Standard 481-1-A 13 inch reel 2,500 (OPTIONAL) Carrier tubes 55 pcs per (STANDARD) ELECTRICAL CHARACTERISTICS@ 250C Unless otherwise specified PART NUMBER DEVICE MARKING STAND OFF VOLTAG E VWM VOLTS MAX BREAKDOWN VOLTAGE VBR @1 mA CLAMPING VOLTAGE VC @ 5 Amp (FIGURE 2) VOLTS LEAKAGE CURRENT ID @ VWM VOLTS CLAMPING VOLTAGE VC @ 1 Amp (FIGURE 2) VOLTS A pF MIN MAX MAX MAX TYP MAX -5 CAPACITANCE (f=1 MHz) @0V C TEMPERATURE COEFFICIENT OF VBR aVBR mV/C SMDA03C-8 SDL8 3.3 4 7.0 9.0 200 300 SMDA05C-8 SDB8 5.0 6.0 9.8 11 40 200 1 SMDA12C-8 SDD8 12.0 13.3 19.0 24 1 75 8 SMDA15C-8 SDF8 15.0 16.7 24.0 30 1 50 11 SMDA24C-8 SDH8 24.0 26.7 43.0 55 1 35 28 NOTE: Transient Voltage Suppression (TVS) product is normally selected based on its stand off voltage VWM. Product selected voltage should be equal to or greater than the continuous peak operating voltage of the circuit to be protected. Application: The SMDAXXC-8 product is designed for transient voltage suppression protection of components at the board level. It is an ideal product to be used for protection of I/O Transceivers. MSC0976.PDF ISO 9001 CERTIFIED REV F 7/06/2000 SMDA03C-8 thru SMDA24C-8 WAVE FORMS 100 Peak Value -- Ipp 8 X 20 Waveform 50 Half-Value -- Ipp 2 I 0 0 10 20 30 t td p t -- Time in microsec FIGURE 2 Pulse Wave Form p FIGURE 1 Peak Pulse Power Vs Pulse Time MOUNTING PAD SO-14 CIRCUIT DIAGRAM SO-14 PACKAGE MSC0976.PDF ISO 9001 CERTIFIED REV F 7/06/2000