Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK HMC783LP6CE v03.0411 FRACTIONAL-N PLL WITH INTEGRATED VCO, 11.5 - 12.5 GHz Features * RF Bandwidth: 11.5 GHz to 12.5 GHz * 24-bit Step Size, Resolution 3 Hz typ * Fractional or Integer Modes * 225 MHz, 14-bit reference path input * Ultra Low Phase Noise 12 GHz; 50 MHz Ref. -95 / -99 dBc/Hz @ 10 kHz (Frac / Int) -134 dBc/Hz @ 1 MHz (Open Loop) * Direct FSK Modulation Mode * Figure of Merit (FOM) -221 / -226 dBc/Hz (Frac / Int) * Cycle Slip Prevention * Read / Write Serial Port, Chip ID * 40 Lead 6 x 6 mm SMT Package: 36 mm Typical Applications 7 * VSAT Radio * Military End-Use * Point-to-Point / Multi-Point Radio * Phased Array Applications PLLS w/ Integrated VCO - SMT * Test Equipment & Industrial Control Functional Diagram [1] Please refer to the pin description table for details 7-1 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC783LP6CE v03.0411 FRACTIONAL-N PLL WITH INTEGRATED VCO, 11.5 - 12.5 GHz General Description The HMC783LP6CE is a fully functioned Fractional-N Phase-Locked-Loop (PLL) with an Integrated Voltage Controlled Oscillator (VCO). The input reference frequency range is 100 kHz to 220 MHz while the advanced deltasigma modulator design in the fractional PLL allows both ultra-fine step sizes and very low spurious products. The highly integrated structure provides excellent phase noise performance over temperature, shock and process. The HMC783LP6CE is packaged in a leadless QFN 6 x 6 mm surface mount package. The output power is 11 dBm typical, making the HMC783LP6CE ideal for driving the LO port of many of Hittite's Hi Linearity and I/Q mixer products. For theory of operation and register map refer to the "PLLs w/ Integrated VCO - Microwave VCOs" Operating Guide. To view the Operating Guide, please visit www.hittite.com and choose HMC783LP6CE from the "Search by Part Number" pull down menu. Parameter Condition Min. Typ. Max. Units 11.5 12 12.5 GHz dBm RF Output Characteristics VCO Output Frequency Range VCO Output Power 5 15 VCO Tuning Voltage 2 13 VCO Tuning Sensitivity V TUNE = +5V Frequency Pulling (into a 2:1 VSWR) Frequency Pushing V TUNE = +5V V 160 MHz/V 8 MHz pp 6 MHz/V Frequency Drift Rate 1.2 MHz/ C Sub Harmonic (1/2) 30 dBc Harmonic (2 ) 24 dBc Harmonic (3rd) 40 dBc V TUNE = +5V Fvco = 12 GHz -110 dBc/Hz Fref = 50 MHz Fvco = 12 GHz Loop BW = 100 kHz -95 / -99 dBc/Hz -221 / -226 dBc/Hz -65 dBc 104 s nd VCO SSB Phase Noise @ 100 kHz Offset (Open Loop) Synthesizer In-Band SSB Phase Noise @ 10 kHz Offset (Frac/Int) Synthesizer Normalized In-Band SSB Phase Noise Floor (Frac/Int) Synthesizer Fractional Spurs [1] Synthesizer Frequency Settling Time (100 MHz Step) 16-Bit Divider Range (Int) 16-Bit Divider Range (Frac) From 12.1 GHz to 12 GHz Loop BW = 100 kHz 16 N Divider Ratio 2 +31 32 65567 N Divider Ratio 216 -1 36 65535 REF Input Characteristics Max Ref Input Frequency (3.3V) 200 Min Ref Input Frequency 100 Ref Input Sensitivity AC Coupled Max Ref Input DC Coupled 500 MHz 200 kHz 700 mVpp 0 VDDIO V 5 pF 16383 1 Ref Input Capacitance 14-Bit Ref Divider Range 225 7 PLLS w/ Integrated VCO - SMT Electrical Specifications, TA = +25 C; VCCVCO, VDDCP, VCCCP = +5V; AVCC, VCCPS VDDPFD, AVDD, RVDD, DVDD, DVDDM, DVDDQ, VDDIO = +3.3V; AGND = DGND = 0V [1] Actual spur level is dependent on loop parameters and will increase at division ratios closest to integer boundaries. Number listed is average value. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 7-2 HMC783LP6CE v03.0411 FRACTIONAL-N PLL WITH INTEGRATED VCO, 11.5 - 12.5 GHz Electrical Specifications (Continued) Parameter Condition Min. Typ. Max. Units Phase Detector Max Phase Detector Frequency (Frac) 70 105 MHz Max Phase Detector Frequency (Int) 140 160 MHz Min Phase Detector Frequency 100 kHz Charge Pump Max Output Current 2 Min Output Current Charge Pump Noise Input referred 50 MHz Ref. mA 500 A -145 dBc/Hz Logic Inputs PLLS w/ Integrated VCO - SMT 7 7-3 VIH Input High Voltage VDDIO-0.4 VDDIO V VIL Input Low Voltage 0 0.4 V VOH Output High Voltage VDDIO-0.4 VDDIO V VOL Output Low Voltage 0 0.4 Logic Outputs Serial Port Max Clock 50 V MHz Power Supply Voltages Analog 3.3V Supplies: AVCC, VDDPFD, AVDD, RVDD, VCCPS AVDD must equal DVDD 3 3.3 3.45 V 3 3.3 3.45 V Logic I/O 1.8 3.3 5.5 V VCCCP must equal VDDCP 4.75 5 5.25 V Total Current Consumption (5V) 145 190 mA Total Current Consumption (3.3V) 90 110 mA 1 10 A Digital Internal Supplies: DVDD, DVDDQ, DVDDM Digital I/O Supplies: VDDIO Analog 5V Supplies: VCCVCO, VDDCP, VCCCP Power Supply Currents CSP Disabled Power Down Current [1] Bias Reference Voltage CSP Enabled Measured with 10 G meter 450 1.880 1.920 A 1.960 V [1] Refers only to the Synthesizer portion of the HMC783LP6CE For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC783LP6CE v03.0411 FRACTIONAL-N PLL WITH INTEGRATED VCO, 11.5 - 12.5 GHz SSB Phase Noise vs. Frequency, Integer Mode SSB Phase Noise vs. Temperature @ 12 GHz, Integer Mode -60 -60 -70 11.5 GHz 12.0 GHz 12.5 GHz -80 PHASE NOISE (dBc/Hz) -90 -100 -110 -120 -130 Temp = 25C Fref = 50 MHz Loop BW = 100 kHz -140 -90 -100 -110 -120 -130 Fref = 50 MHz Loop BW = 100 kHz -140 -150 10 +25 C +85 C -40 C -80 -150 2 10 3 10 4 10 5 10 6 10 7 10 2 10 3 -60 -60 -70 -70 -80 -90 -100 -110 -120 Temp = 25C Fref = 50 MHz Loop BW = 100 kHz -150 2 10 10 3 4 10 5 10 6 10 7 -120 Fref = 10MHz Loop BW= 10kHz -130 Fref = 50MHz Loop BW=100kHz 10 3 10 4 10 5 10 6 10 7 OFFSET FREQUENCY (Hz) Typical Reference Sensitivity vs. Frequency, 3.3V [1] 20 12.2 10 SENSITIVITY (dBm) FREQUENCY (GHz) 10 -110 12.3 12.1 CSP OFF 11.9 CSP ON 11.7 R = Max, +25C R = Max, +85C 0 -10 R = 3, +25C R = 3, +85C -20 7 -30 -40 11.6 -20 6 -90 -150 2 10 7 Example of Cycle Slip Prevention Hop from 12.2 to 11.7 GHz 11.8 10 -100 OFFSET FREQUENCY (Hz) 12 5 -80 -140 10 10 SSB Phase Noise vs. Reference Freq. & Loop BW @ 12 GHz, Integer Mode PHASE NOISE (dBc/Hz) PHASE NOISE (dBc/Hz) SSB Phase Noise Fractional Spurs @ 12.002 GHz -140 4 OFFSET FREQUENCY (Hz) OFFSET FREQUENCY (Hz) -130 10 PLLS w/ Integrated VCO - SMT PHASE NOISE (dBc/Hz) -70 -50 -10 0 10 20 30 40 50 TIME (SEC) 60 70 80 0 50 100 150 200 250 300 FREQUENCY (MHz) [1] R refers to the reference path division ratio For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 7-4 HMC783LP6CE v03.0411 FRACTIONAL-N PLL WITH INTEGRATED VCO, 11.5 - 12.5 GHz Frequency vs. Tuning Voltage, Vcc = +5V 13.4 13.4 13.1 13.1 OUTPUT FREQUENCY (GHz) OUTPUT FREQUENCY (GHz) Frequency vs. Tuning Voltage, T = 25C 12.8 12.5 12.2 11.9 11.6 11.3 Vcc=4.75V Vcc=5.00V Vcc=5.25V 11 10.7 12.2 11.9 11.6 11.3 +25C +85C -40C 11 10.4 0 1 2 3 4 7 5 6 7 8 9 10 11 12 0 13 1 2 3 4 Sensitivity vs. Tuning Voltage, Vcc = +5V 6 7 8 9 10 11 12 13 10 11 12 13 Output Power vs. Tuning Voltage, Vcc = +5V 700 14 13 500 OUTPUT POWER (dBm) 600 SENSITIVITY (MHz/V) 5 TUNING VOLTAGE (V) TUNING VOLTAGE (V) +25C +85C -40C 400 300 200 100 12 11 10 9 8 7 +25C +85C -40C 6 5 0 4 0 1 2 3 4 5 6 7 8 9 10 11 12 13 0 1 2 3 4 TUNING VOLTAGE (V) 6 7 8 9 Open Loop VCO SSB Phase Noise vs. Tuning Voltage 0 -20 -20 -40 SSB PHASE NOISE (dBc/Hz) 0 +25C +85C -40C -60 -80 -100 -120 -140 10KHz Offset 100KHz Offset -40 -60 -80 -100 -120 -140 -160 10 5 TUNING VOLTAGE (V) Open Loop VCO SSB Phase Noise @ Vtune = +5V SSB PHASE NOISE (dBc/Hz) PLLS w/ Integrated VCO - SMT 12.5 10.7 10.4 3 10 4 10 5 10 OFFSET FREQUENCY (GHz) 7-5 12.8 6 10 7 1 2 3 4 5 6 7 8 9 10 11 12 13 TUNING VOLTAGE (V) For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC783LP6CE v03.0411 FRACTIONAL-N PLL WITH INTEGRATED VCO, 11.5 - 12.5 GHz Pin Descriptions Function Description 1, 9 - 13, 22, 36 N/C No Connection. These pins may be connected to RF/DC ground. Performance will not be affected. 2 - 4, 7, 37, 39 GND [1] These pins must be connected to RF/DC Ground 5 GND These pins and package bottom must be connected to RF/DC Ground 8 VCCVCO2 [2] 40 VCCVCO1 6 VTUNE Control Voltage Input. Modulation port bandwidth dependent on drive source impedance. 14 ACG AC Ground. This pin must be connected to an external capacitor to ground. 15 AVCC Analog Power supply pin for the RF Section. A decoupling capacitor to the ground plane should be placed as close as possible to this pin. Nominally 3.3V 16 VDDCP +5V Power Supply for charge pump digital section +5V Power Supply for VCO 17 VCCCP +5V Power Supply for the charge pump analog section 18 CP Charge pump output 19 VDDPFD Analog Power supply for the phase frequency detector, Nominally 3.3V 20 BIAS [3] External bypass decoupling for precision bias circuits, 1.920V 20 mV is generated internally 21 AVDD Analog Power supply for analog ref paths, Nominally 3.3V 23 REFN Reference input (Negative or AC coupled to GND) 24 REFP Reference input (Positive) 25 RVDD Ref path supply 26 DVDDQ Digital supply for Substrate, Nominally 3.3V 27 CE Chip Enable 28 SEN Serial port latch enable input 29 SCK Serial port clock input 30 SDI Serial port data input 31 DVDD Power supply pin for internal digital circuitry. Nominally 3.3V 32 VDDIO Power Supply for digital I/O driver 33 LD_SDO Lock Detect, Main Serial Data Output or VCO Serial Port Data Out 34 VCCPS Analog Power Supply for Prescaler, Nominally 3.3V 35 DVDDM Digital Power Supply for M-Counter, Nominally 3.3V 38 RFOUT RF output (AC coupled). 7 PLLS w/ Integrated VCO - SMT Pin Number [1] This pin is not connected internally, however, this pin must be connected to GND to maintain product family pin for pin compatibility. [2] This pin is not connected internally, however, this pin must be connected to Vcc to maintain product family pin for pin compatibility. [3] BIAS ref voltage (pin 20) cannot drive an external load, and must be measured with a 10 GOhm meter such as Agilent 34410A; a typical 10 Mohm DVM will read erroneously. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 7-6 HMC783LP6CE v03.0411 FRACTIONAL-N PLL WITH INTEGRATED VCO, 11.5 - 12.5 GHz Pin Schematic Equivalents Pins Equivalent Schematic RFOUT VCCVCO1 PLLS w/ Integrated VCO - SMT 7 7-7 VTUNE GND SEN, CE, SCK, SDI LD_SDO CP For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC783LP6CE v03.0411 FRACTIONAL-N PLL WITH INTEGRATED VCO, 11.5 - 12.5 GHz Pin Schematic Equivalents (Continued) Pins Equivalent Schematic Bias REFN, REFP For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com PLLS w/ Integrated VCO - SMT 7 7-8 HMC783LP6CE v03.0411 FRACTIONAL-N PLL WITH INTEGRATED VCO, 11.5 - 12.5 GHz Evaluation Circuit 3VDIGITAL 3VANALOG 3VDIGITAL C12 100NF C10 10PF C14 100NF C13 10PF C8 10PF C9 100NF CEN 2 R8 100K A B C D 1 JP1 3VDIGITAL J3 5016 C38 1NF JP3 2 C32 4.7UF 11 12 13 14 15 16 17 18 19 20 GND U1 HMC783LP6CE SDI SCK SEN CE DVDDQ RVDD REFP REFN NC AVDD E F G H C 100N C35 100NF 1 C31 30 29 28 27 26 25 24 23 22 21 C21 1NF SYNTH 5016 NC GND GND GND GND VTUNE GND VCCVCO2 NC NC NC NC NC ACG AVCC VDDCP VCCCP CP VDDPFD BIAS 1 2 3 4 5 6 7 8 9 10 VCCVCO1 GND RFOUT GND NC DVDDM VCCPS LD_SDO VDDIO DVDD C1 1NF 1 SDO 40 39 38 37 36 35 34 33 32 31 2 C4 4.7UF TP5 PLLS w/ Integrated VCO - SMT 50 Ohm Co-Planar Trace JP2 7 RFout 5VVCO LD TP6 1 R1 100K C15 100PF R20 1K 100PF R23 C65 R27 DEPOP DEPOP 0 C61 3.9NF R28 DEPOP L1 I DEPOP R21 R12 30 DEPOP C62 R3 1K +15V TP4 5016 TP3 5016 GND C57 22UF C58 4.7UF C39 1NF 7 6 THS4031IDGN 4 620 C64 C33 1.5NF J C37 3.9NF DEPOP K R25 2 U5 FB3 1000 DEPOP DEPOP FB4 1000 C63 R13 182 R4 DEPOP 3 R26 R22 0 L DEPOP R15 10K C60 1NF R14 JP6 1 2 10K 7-9 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com M HMC783LP6CE v03.0411 FRACTIONAL-N PLL WITH INTEGRATED VCO, 11.5 - 12.5 GHz Evaluation Circuit (Continued from page 9) VDIGITAL Header to USB Board J1 R1 100K 2 3 4 5 6 7 8 9 10 11 12 NC NC GND 3VDIGITAL REFin C29 50 Ohm Trace 1 R41 1K JP5 1 R11 4.02K 5VVCO 1000 C36 100NF J2 U9 LP3878MR-ADJ SD 2 R40 4.02K C67 1.2NF 6 5 ADJ VIN BPASS VOUT GND 8 4 R2 120 C40 56 R7 120 100NF TCXO 3 FOUT Y2 GND VDD VC R9 4 1 C6 10PF C28 100NF 3 C74 4.7UF C73 10NF C68 4.7UF 3VTCXO R17 1K 10 R16 4.02K DEPOP 5VCP R10 0 U8 LP3878MR-ADJ SD R24 2 C30 DEPOP C46 100NF C44 1.2NF 6 5 ADJ VIN BPASS VOUT GND 8 4 C43 100NF 1 3 C48 4.7UF C47 10NF C45 4.7UF 3VANALOG I C16 10PF C18 100NF U2 LP5900-3_3V 3VANALOG 3VANALOG C22 10PF C23 100NF 5VCP C24 10PF C25 100NF C19 10PF 1 GND EN 6 R5 10K 4 3 U4 LP5900-3_3V 3VDIGITAL C51 10PF VIN VOUT C20 100NF 1 C52 100NF VOUT VIN C17 4.7UF 6 4 GND EN C11 100NF 3 R18 10K C50 100NF C49 4.7UF 3VANALOG C26 10PF C27 100NF U6 LP5900-3_3V 3VTCXO 1 C55 10PF C56 100NF VOUT VIN GND EN 6 4 3 C54 100NF JP4 R19 10K 1 M 7 C41 100NF 1 100NF R6 L FB1 5016 C3 100NF C34 100NF K TP1 C59 4.7UF C7 100NF C2 10PF J 1000 C42 100NF NC 3VANALOG E F G H FB2 5016 NC TLW-106-05-T-D C5 10PF TP2 PLLS w/ Integrated VCO - SMT SCK SDI SDO SEN CEN A B C D 5.5V 3VDIGITAL 1 C53 4.7UF 2 5VCP For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 7 - 10 HMC783LP6CE v03.0411 FRACTIONAL-N PLL WITH INTEGRATED VCO, 11.5 - 12.5 GHz ader to USB Board J1 2 3 4 5 6 7 8 9 10 11 12 TP2 FB2 1000 5016 NC C42 100NF NC NC NC GND TLW-106-05-T-D 3VDIGITAL TP1 C59 4.7UF FB1 1000 5016 C7 100NF 1 C3 100NF R11 4.02K 5VVCO 7 REFin C29 Ohm Trace 1 R41 1K JP5 3VANALOG C2 0PF C36 100NF J2 U9 LP3878MR-ADJ SD 2 R40 4.02K C67 1.2NF 6 5 ADJ VIN BPASS VOUT GND 8 4 C41 100NF 1 3 C74 4.7UF C73 10NF C68 4.7UF 100NF TCXO 3 PLLS w/ Integrated VCO - SMT 00NF 5.5V 3VDIGITAL 1 C5 0PF C40 Evaluation Circuit (Continued from page 10) FOUT Y2 GND VDD 4 VC 1 R9 C6 10PF C28 100NF 3VTCXO R17 1K 10 SD R24 2 R16 4.02K DEPOP C30 DEPOP 5VCP R10 0 U8 LP3878MR-ADJ C46 100NF C44 1.2NF 6 5 ADJ VIN BPASS VOUT GND 8 4 1 3 C43 100NF C48 4.7UF C11 100NF C17 4.7UF C50 100NF C49 4.7UF C54 100NF JP4 C53 4.7UF C47 10NF C45 4.7UF 3VANALOG C18 100NF U2 LP5900-3_3V 3VANALOG 3VANALOG C23 100NF 5VCP C25 100NF C19 10PF 1 C20 100NF GND EN 6 R5 10K 4 3 U4 LP5900-3_3V 3VDIGITAL C51 10PF VIN VOUT 1 C52 100NF VOUT VIN 6 4 GND EN 3 R18 10K 3VANALOG C27 100NF U6 LP5900-3_3V 3VTCXO 1 C55 10PF C56 100NF VOUT VIN GND EN 3 6 4 R19 10K 1 2 5VCP 7 - 11 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC783LP6CE v03.0411 FRACTIONAL-N PLL WITH INTEGRATED VCO, 11.5 - 12.5 GHz Absolute Maximum Ratings Nominal 3.3V Supplies to GND -0.3V to +3.6V Nominal Digital Supply Relative to 3.3V Analog Supply -0.3V to +0.3V Nominal 5V Supply to GND -0.3 to +5.5V Vtune 0 to +15V Storage Temperature -65 to +150C Max Peak Reflow Temperature 260 C ESD Sensitivity (HBM) Class 1A Reliability Information Junction Temperature to Maintain 1 Million Hour MTTF 135 C Nominal Junction Temperature (T=85 C) 120 C Thermal Resistance (Junction to GND Paddle, 5V Supply) 48.3 C/W Operating Temperature -40 to +85C 7 PLLS w/ Integrated VCO - SMT Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2.DIMENSIONS ARE IN INCHES [MILLIMETERS]. 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE 4. PAD BURR LENGTH SHALL BE 0.15 mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED PCB LAND PATTERN. Package Information Part Number Package Body Material Lead Finish MSL Rating Package Marking [1] HMC783LP6CE RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL3 H783 XXXX [1] 4-Digit lot number XXXX For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 7 - 12 HMC783LP6CE v03.0411 FRACTIONAL-N PLL WITH INTEGRATED VCO, 11.5 - 12.5 GHz Evaluation PCB PLLS w/ Integrated VCO - SMT 7 7 - 13 The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC783LP6CE v03.0411 FRACTIONAL-N PLL WITH INTEGRATED VCO, 11.5 - 12.5 GHz List of Materials for Evaluation PCB 127272 [1] Description J1 Dual Row Terminal Strip J2, J3 PCB Mount SMA RF Connector JP1 - JP6 Single Row Terminal Strip C1, C21, C38 - C39, C60 1000 pF Capacitor, 0402 Pkg. C2, C5, C6, C8, C10, C13, C16, C19, C22, C24, C26, C51, C55 10 pF Capacitor, 0402 Pkg. C3, C7, C9, C11, C12, C14, C18, C20, C23, C25, C27 - C29, C34 - C36, C40 - C43, C46, C50, C52, C54, C56 0.1 F Capacitor, 0402 Pkg. C4, C17, C32, C45, C48, C49, C53, C68, C74 4.7 F Capacitor, 0805 Pkg. C15, C31 100 pF Capacitor, 0402 Pkg. C44, C67 1200 pF Capacitor, 0402 Pkg. C33 1500 pF Capacitor, 0402 Pkg. C37 0.039 F Capacitor, 0603 Pkg. C47, C73 10,000 pF Capacitor, 0402 Pkg. C57 22 F Tantalum Capacitor, Case D C58, C59 4.7 F Tantalum Capacitor, Case B C61 3900 pF Capacitor, 0402 Pkg. FB1 - FB4 1000 Ohm 200 mA Ferrite Chip, 0805 Pkg. R1, R8 100k Ohm Resistor, 0402 Pkg. R2, R7 120 Ohm Resistor, 0402 Pkg. R3, R17, R20, R41 1k Ohm Resistor, 0402 Pkg. R4 620 Ohm Resistor, 0402 Pkg. R5, R14, R15, R18, R19 10k Ohm Resistor, 0402 Pkg. R6 56 Ohm Resistor, 0402 Pkg. R9 10 Ohm Resistor, 0402 Pkg. R10, R22, R23 Zero Ohm Resistor, 0402 Pkg. R11, R16, R40 4.02k Ohm Resistor, 0402 Pkg. R13 182 Ohm Resistor, 0402 Pkg. R21 30 Ohm Resistor, 0402 Pkg. TP1 - TP6 Test Point PC Compact SMT U1 HMC783LP6CE Fractional-N PLL, with Integrated VCO U2, U4, U6 Low Noise 3.3V, 100 mA Linear Regulator U5 Low Noise Op-Amp, THS4031IDGN U8, U9 5V, 800mA Voltage Regulator Y2 3.3V, 50 MHz VCXO Crystal Oscillator PCB [2] 125536 Evaluation Board 7 PLLS w/ Integrated VCO - SMT Item [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 or Arlon 25FR and FR4 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 7 - 14 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Analog Devices Inc.: 127272-HMC783LP6CE HMC783LP6CE 127900-HMC783LP6CE HMC783LP6CETR