LM12454, LM12458, LM12H458
www.ti.com
SNAS079A MAY 2004REVISED FEBRUARY 2006
LM12454/LM12458/LM12H458 12-Bit + Sign Data Acquisition System with Self-Calibration
Check for Samples: LM12454,LM12458,LM12H458
1FEATURES DESCRIPTION
23 Three operating modes: 12-bit + sign, 8-bit + The LM12458, and LM12H458 are highly integrated
sign, and “watchdog” Data Acquisition Systems. Operating on just 5V, they
Single-ended or differential inputs combine a fully-differential self-calibrating (correcting
Built-in Sample-and-Hold and 2.5V bandgap linearity and zero errors) 13-bit (12-bit + sign) analog-
reference to-digital converter (ADC) and sample-and-hold (S/H)
with extensive analog functions and digital
Instruction RAM and event sequencer functionality. Up to 32 consecutive conversions, using
8-channel multiplexer two's complement format, can be stored in an internal
32-word conversion FIFO 32-word (16-bit wide) FIFO data buffer. An internal 8-
word RAM can store the conversion sequence for up
Programmable acquisition times and to eight acquisitions through the LM12(H)458's eight-
conversion rates input multiplexer. The obsolete LM12454 has a four-
Self-calibration and diagnostic mode channel multiplexer, a differential multiplexer output,
8- or 16-bit wide data bus microprocessor or and a differential S/H input. The LM12(H)458 can
DSP interface also operate with 8-bit + sign resolution and in a
supervisory “watchdog” mode that compares an input
signal against two programmable limits.
APPLICATIONS Programmable acquisition times and conversion rates
Data Logging are possible through the use of internal clock-driven
Instrumentation timers. The reference voltage input can be externally
Process Control generated for absolute or ratiometric operation or can
be derived using the internal 2.5V bandgap
Energy Management reference.
Inertial Guidance All registers, RAM, and FIFO are directly addressable
KEY SPECIFICATIONS through the high speed microprocessor interface to
either an 8-bit or 16-bit data bus. The LM12(H)458
Resolution: 12-bit + sign or 8-bit + sign includes a direct memory access (DMA) interface for
13-bit conversion time: 8.8 μs, 5.5 μs (H) (max) high-speed conversion data transfer.
9-bit conversion time: 4.2 μs, 2.6 μs (H) (max) Additional applications information can be found in
13-bit Through-put rate: applications notes AN-906, AN-947 and AN-949.
88k samples/s (min)
140k samples/s (H) (min)
Comparison time: 2.2 μs (max)
("watchdog” mode): 1.4 μs (H) (max)
ILE: ±1 LSB (max)
VIN range: GND to VA +
Power dissipation: 30 mW, 34 mW (H) (max)
Stand-by mode: 50 μW (typ)
Single supply: 3V to 5.5V
1Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2TRI-STATE is a registered trademark of Texas Instruments.
3All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date. Copyright © 2004–2006, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
LM12454, LM12458, LM12H458
SNAS079A MAY 2004REVISED FEBRUARY 2006
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
CONNECTION DIAGRAM
* Pin names in ( ) apply to the obsolete LM12454 and LM12H454.
Figure 1. See Package Number FN0044A Figure 2. See Package Number PGB0044A
FUNCTIONAL DIAGRAM
LM12454
The LM12(H)454 is obsolete
2Submit Documentation Feedback Copyright © 2004–2006, Texas Instruments Incorporated
Product Folder Links: LM12454 LM12458 LM12H458
LM12454, LM12458, LM12H458
www.ti.com
SNAS079A MAY 2004REVISED FEBRUARY 2006
LM12(H)458
Copyright © 2004–2006, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: LM12454 LM12458 LM12H458
LM12454, LM12458, LM12H458
SNAS079A MAY 2004REVISED FEBRUARY 2006
www.ti.com
ABSOLUTE MAXIMUM RATINGS (1) (2)
Supply Voltage (VA+ and VD+) 6.0V
Voltage at Input and Output Pins, except analog inputs 0.3V to (V++ 0.3V)
Voltage at Analog Inputs 5V to (V++ 5V)
|VA+VD+| 300 mV
Input Current at Any Pin (3) ±5 mA
Package Input Current (3) ±20 mA
Power Dissipation, PQFP
(TA= 25°C) (4) 875 mW
Storage Temperature 65°C to +150°C
Lead Temperature
PQFP, Infrared, 15 sec. +300°C
PLCC, Solder, 10 sec. +250°C
ESD Susceptibility (5) 1.5 kV
(1) All voltages are measured with respect to GND, unless otherwise specified.
(2) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but does not specify performance limits. For specifications and test conditions, see the Electrical
Characteristics. The specifications apply only for the test conditions listed. Some performance characteristics may degrade when the
device is not operated under the listed test conditions.
(3) When the input voltage (VIN) at any pin exceeds the power supply rails (VIN < GND or VIN > (VA+ or VD+)), the current at that pin should
be limited to 5 mA. The 20 mA maximum package input current rating allows the voltage at any four pins, with an input current of 5 mA,
to simultaneously exceed the power supply voltages.
(4) The maximum power dissipation must be derated at elevated temperatures and is dictated by TJmax (maximum junction temperature),
θJA (package junction to ambient thermal resistance), and TA(ambient temperature).
(5) Human body model, 100 pF discharged through a 1.5 kΩresistor.
OPERATING RATINGS(1) (2)
Temperature Range
(Tmin TATmax)40°C TA85°C
Supply Voltage
VA+, VD+ 3.0V to 5.5V
|VA+VD+| 100 mV
VIN+ Input Range GND VIN+ VA+
VINInput Range GND VINVA+
VREF+ Input Voltage 1V VREF+ VA+
VREFInput Voltage 0V VREFVREF+ 1V
VREF+ VREF1V VREF VA+
VREF Common Mode Range (3) 0.1 VA+VREFCM 0.6 VA+
TJ(MAX) 150°C
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but does not specify performance limits. For specifications and test conditions, see the Electrical
Characteristics. The specifications apply only for the test conditions listed. Some performance characteristics may degrade when the
device is not operated under the listed test conditions.
(2) All voltages are measured with respect to GND, unless otherwise specified.
(3) VREFCM (Reference Voltage Common Mode Range) is defined as (VREF+ + VREF)/2.
4Submit Documentation Feedback Copyright © 2004–2006, Texas Instruments Incorporated
Product Folder Links: LM12454 LM12458 LM12H458
LM12454, LM12458, LM12H458
www.ti.com
SNAS079A MAY 2004REVISED FEBRUARY 2006
CONVERTER CHARACTERISTICS (1) (2) (3) (4)
The following specifications apply to the LM12454, LM12458, and LM12H458 for VA+=VD+ = 5V, VREF+ = 5V, VREF= 0V, 12-
bit + sign conversion mode, fCLK = 8.0 MHz (LM12H458) or fCLK = 5.0 MHz (LM12454/8), RS= 25Ω, source impedance for
VREF+ and VREF25Ω, fully-differential input with fixed 2.5V common-mode voltage, and minimum acquisition time unless
otherwise specified. Boldface limits apply for TA= TJ= TMIN to TMAX; all other limits TA= TJ= 25°C.
Symbol Parameter Conditions Typical (5) Limits (6) Units
ILE Integral Linearity Error (7) (8) After Auto-Cal ±1/2 ±1LSB (max)
TUE Total Unadjusted Error(7) After Auto-Cal ±1 LSB
Resolution with No Missing Codes (7) After Auto-Cal 13 Bits (max)
DNL Differential Non-Linearity After Auto-Cal ±¾LSB (max)
After Auto-Cal ±1
Zero Error (9) (8) LM12H458 ±1/2 ±1.5 LSB (max)
Positive Full-Scale Error (7) (8) After Auto-Cal ±1/2 ±2 LSB (max)
Negative Full-Scale Error (7) (8) After Auto-Cal ±1/2 ±2 LSB (max)
DC Common Mode Error (10) ±2 ±3.5 LSB (max)
8-Bit + Sign and “Watchdog” Mode
ILE ±1/2 LSB (max)
Integral Linearity Error (7)
8-Bit + Sign and “Watchdog” Mode Total
TUE After Auto-Zero ±1/2 ±3/4 LSB (max)
Unadjusted Error
8-Bit + Sign and “Watchdog” Mode Resolution 9Bits (max)
with No Missing Codes
8-Bit + Sign and “Watchdog” Mode
DNL ±3/4 LSB (max)
Differential Non-Linearity
8-Bit + Sign and “Watchdog” Mode Zero Error After Auto-Zero ±1/2 LSB (max)
8-Bit + Sign and “Watchdog” Full-Scale Error ±1/2 LSB (max)
8-Bit + Sign and “Watchdog” Mode ±1/8 LSB
DC Common Mode Error
Multiplexer Channel-to-Channel Matching ±0.05 LSB
GND V (min)
VIN+ Non-Inverting Input Range VA+V (max)
GND V (min)
VINInverting Input Range VA+V (max)
VA+V (min)
VIN+ VINDifferential Input Voltage Range VA+V (max)
V (min)
GND V (max)
Common Mode Input Voltage Range VA+
(1) Two on-chip diodes are tied to each analog input through a series resistor, as shown below. Input voltage magnitude up to 5V above
VA+ or 5V below GND will not damage the LM12454 or the LM12(H)458. However, errors in the A/D conversion can occur if these
diodes are forward biased by more than 100 mV. As an example, if VA+ is 4.5 VDC, full-scale input voltage must be 4.6 VDC to ensure
accurate conversions. See Figure 3
(2) VA+ and VD+ must be connected together to the same power supply voltage and bypassed with separate capacitors at each V+pin to
assure conversion/comparison accuracy.
(3) Accuracy is ensured when operating at fCLK = 5 MHz for the LM12454/8 and fCLK = 8 MHz for the LM12H458.
(4) With the test condition for VREF (VREF+ VREF) given as +5V, the 12-bit LSB is 1.22 mV and the 8-bit/“Watchdog” LSB is 19.53 mV.
(5) Typical figures are at TA= 25°C and represent most likely parametric norm.
(6) Limits are to AOQL (Average Output Quality Level).
(7) Positive integral linearity error is defined as the deviation of the analog value, expressed in LSBs, from the straight line that passes
through positive full-scale and zero. For negative integral linearity error the straight line passes through negative full-scale and zero.
(See Figure 5 Figure 6).
(8) The LM12(H)454/8's self-calibration technique ensures linearity and offset errors as specified, but noise inherent in the self-calibration
process will result in a repeatability uncertainty of ±0.10 LSB.
(9) Zero error is a measure of the deviation from the mid-scale voltage (a code of zero), expressed in LSB. It is the worst-case value of the
code transitions between 1 to 0 and 0 to +1 (see Figure 7).
(10) The DC common-mode error is measured with both inputs shorted together and driven from 0V to 5V. The measured value is referred to
the resulting output value when the inputs are driven with a 2.5V signal.
Copyright © 2004–2006, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: LM12454 LM12458 LM12H458
LM12454, LM12458, LM12H458
SNAS079A MAY 2004REVISED FEBRUARY 2006
www.ti.com
CONVERTER CHARACTERISTICS (1) (2) (3) (4) (continued)
The following specifications apply to the LM12454, LM12458, and LM12H458 for VA+=VD+ = 5V, VREF+ = 5V, VREF= 0V, 12-
bit + sign conversion mode, fCLK = 8.0 MHz (LM12H458) or fCLK = 5.0 MHz (LM12454/8), RS= 25Ω, source impedance for
VREF+ and VREF25Ω, fully-differential input with fixed 2.5V common-mode voltage, and minimum acquisition time unless
otherwise specified. Boldface limits apply for TA= TJ= TMIN to TMAX; all other limits TA= TJ= 25°C.
Symbol Parameter Conditions Typical (5) Limits (6) Units
Zero Error VA+=VD+ = 5V ±10% ±0.2 ±1.75 LSB (max)
Power Supply Sensitivity VREF+ = 4.5V, VREF=
PSS Full-Scale Error ±0.4 ±2LSB (max)
(11) GND
Linearity Error ±0.2 LSB
CREF VREF+/VREFInput Capacitance 85 pF
CIN Selected Multiplexer Channel Input Capacitance 75 pF
(11) Power Supply Sensitivity is measured after Auto-Zero and/or Auto-Calibration cycle has been completed with VA+ and VD+ at the
specified extremes.
6Submit Documentation Feedback Copyright © 2004–2006, Texas Instruments Incorporated
Product Folder Links: LM12454 LM12458 LM12H458
LM12454, LM12458, LM12H458
www.ti.com
SNAS079A MAY 2004REVISED FEBRUARY 2006
CONVERTER AC CHARACTERISTICS (1) (2) (3) (4)
The following specifications apply to the LM12454, LM12458, and LM12H458 for VA+=VD+ = 5V, VREF+ = 5V, VREF= 0V, 12-
bit + sign conversion mode, fCLK = 8.0 MHz (LM12H458) or fCLK = 5.0 MHz (LM12454/8), RS= 25Ω, source impedance for
VREF+ and VREF25Ω, fully-differential input with fixed 2.5V common-mode voltage, and minimum acquisition time unless
otherwise specified. Boldface limits apply for TA= TJ= TMIN to TMAX; all other limits TA= TJ= 25°C.
Symbol Parameter Conditions Typical (5) Limits (6) Units
%
Clock Duty Cycle 50 40 % (min)
60 % (max)
13-Bit Resolution, Sequencer State 44 (tCLK)44 (tCLK) + 50 ns (max)
S5 (Figure 45)
tCConversion Time 9-Bit Resolution, Sequencer State S5 21 (tCLK)21 (tCLK) + 50 ns (max)
(Figure 45)
Sequencer State S7 (Figure 45) Built- 9 (tCLK)9 (tCLK) + 50 ns (max)
in minimum for 13-Bits
tAAcquisition Time Built-in minimum for 9-Bits and 2 (tCLK)2 (tCLK) + 50 ns (max)
“Watchdog” mode
tZAuto-Zero Time Sequencer State S2 (Figure 45) 76 (tCLK)76 (tCLK) + 50 ns (max)
tCAL 4944 (tCLK) + 50
Full Calibration Time Sequencer State S2 (Figure 45) 4944 (tCLK) (max)
ns
89 88 kHz (min)
Throughput Rate (7) LM12H458 142 140 kHz (min)
“Watchdog” Mode Comparison Time Sequencer States S6, S4, and S5
tWD 11 (tCLK)11 (tCLK) + 50 ns (max)
(Figure 45)
VIN = ±5V
fIN = 1 kHz 77.5 dB
DSNR Differential Signal-to-Noise Ratio fIN = 20 kHz 75.2 dB
fIN = 40 kHz 74.7 dB
VIN = 5 Vp-p
fIN = 1 kHz 69.8 dB
SESNR Single-Ended Signal-to-Noise Ratio fIN = 20 kHz 69.2 dB
fIN = 40 kHz 66.6 dB
VIN = ±5V
fIN = 1 kHz 76.9 dB
Differential Signal-to-Noise +
DSINAD Distortion Ratio fIN = 20 kHz 73.9 dB
fIN = 40 kHz 70.7 dB
VIN = 5 Vp-p
fIN = 1 kHz 69.4 dB
Single-Ended Signal-to-Noise +
SESINAD Distortion Ratio fIN = 20 kHz 68.3 dB
fIN = 40 kHz 65.7 dB
(1) Two on-chip diodes are tied to each analog input through a series resistor, as shown below. Input voltage magnitude up to 5V above
VA+ or 5V below GND will not damage the LM12454 or the LM12(H)458. However, errors in the A/D conversion can occur if these
diodes are forward biased by more than 100 mV. As an example, if VA+ is 4.5 VDC, full-scale input voltage must be 4.6 VDC to ensure
accurate conversions. See Figure 3
(2) VA+ and VD+ must be connected together to the same power supply voltage and bypassed with separate capacitors at each V+pin to
assure conversion/comparison accuracy.
(3) Accuracy is ensured when operating at fCLK = 5 MHz for the LM12454/8 and fCLK = 8 MHz for the LM12H458.
(4) With the test condition for VREF (VREF+ VREF) given as +5V, the 12-bit LSB is 1.22 mV and the 8-bit/“Watchdog” LSB is 19.53 mV.
(5) Typical figures are at TA= 25°C and represent most likely parametric norm.
(6) Limits are to AOQL (Average Output Quality Level).
(7) The Throughput Rate is for a single instruction repeated continuously. Sequencer states 0 (1 clock cycle), 1 (1 clock cycle), 7 (9 clock
cycles) and 5 (44 clock cycles) are used (see Figure 45). One additional clock cycle is used to read the conversion result stored in the
FIFO, for a total of 56 clock cycles per conversion. The Throughput Rate is fCLK (MHz)/N, where N is the number of clock
cycles/conversion.
Copyright © 2004–2006, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: LM12454 LM12458 LM12H458
LM12454, LM12458, LM12H458
SNAS079A MAY 2004REVISED FEBRUARY 2006
www.ti.com
CONVERTER AC CHARACTERISTICS (1) (2) (3) (4) (continued)
The following specifications apply to the LM12454, LM12458, and LM12H458 for VA+=VD+ = 5V, VREF+ = 5V, VREF= 0V, 12-
bit + sign conversion mode, fCLK = 8.0 MHz (LM12H458) or fCLK = 5.0 MHz (LM12454/8), RS= 25Ω, source impedance for
VREF+ and VREF25Ω, fully-differential input with fixed 2.5V common-mode voltage, and minimum acquisition time unless
otherwise specified. Boldface limits apply for TA= TJ= TMIN to TMAX; all other limits TA= TJ= 25°C.
Symbol Parameter Conditions Typical (5) Limits (6) Units
VIN = ±5V
fIN = 1 kHz 85.8 dB
DTHD Differential Total Harmonic Distortion fIN = 20 kHz 79.9 dB
fIN = 40 kHz 72.9 dB
VIN = 5 Vp-p
fIN = 1 kHz 80.3 dB
Single-Ended Total Harmonic
SETHD Distortion fIN = 20 kHz 75.6 dB
fIN = 40 kHz 72.8 dB
VIN = ±5V
fIN = 1 kHz 12.6 Bits
DENOB Differential Effective Number of Bits fIN = 20 kHz 12.2 Bits
fIN = 40 kHz 12.1 Bits
VIN = 5 Vp-p
fIN = 1 kHz 11.3 Bits
SEENOB Single-Ended Effective Number of Bits fIN = 20 kHz 11.2 Bits
fIN = 40 kHz 10.8 Bits
VIN = ±5V
fIN = 1 kHz 87.2 dB
Differential Spurious Free Dynamic
DSFDR Range fIN = 20 kHz 78.9 dB
fIN = 40 kHz 72.8 dB
VIN = 5 VP-P, fIN = 40 kHz, 76 dB
LM12454 MUXOUT Only
Multiplexer Channel-to-Channel
Crosstalk VIN = 5 VP-P, fIN = 40 kHz, 78 dB
LM12(H)458 MUX plus Converter
tPU Power-Up Time 10 ms
tWU Wake-Up Time 10 ms
8Submit Documentation Feedback Copyright © 2004–2006, Texas Instruments Incorporated
Product Folder Links: LM12454 LM12458 LM12H458
LM12454, LM12458, LM12H458
www.ti.com
SNAS079A MAY 2004REVISED FEBRUARY 2006
DC CHARACTERISTICS (1) (2) (3)
The following specifications apply to the LM12454, LM12458, and LM12H458 for VA+=VD+ = 5V, VREF+ = 5V, VREF= 0V,
fCLK = 8.0 MHz (LM12H454/8) or fCLK = 5.0 MHz (LM12458), and minimum acquisition time unless otherwise specified.
Boldface limits apply for TA= TJ= TMIN to TMAX; all other limits TA= TJ= 25°C.
Symbol Parameter Conditions Typical (4) Limits (5) Units
CS = “1”
ID+ VD+ Supply Current LM12454/8 0.55 1.0 mA (max)
LM12H458 0.55 1.2 mA (max)
CS = “1”
IA+ VA+ Supply Current LM12454/8 3.1 5.0 mA (max)
LM12H458 3.1 5.5 mA (max)
Stand-By Supply Current (ID+) + (IA+) Clock Stopped 10 μA (max)
IST [Power-Down Mode Selected] 8 MHz Clock 40 μA (max)
VA+ = 5.5V
ON-Channel = 5.5V, 0.1 0.3 μA (max)
Multiplexer ON-Channel Leakage OFF-Channel = 0V
Current ON-Channel = 0V 0.1 0.3 μA (max)
OFF-Channel = 5.5V
VA+ = 5.5V
ON-Channel = 5.5V 0.1 0.3 μA (max)
Multiplexer OFF-Channel Leakage OFF-Channel = 0V
Current ON-Channel = 0V 0.3
0.1 μA (max)
OFF-Channel = 5.5V
LM12454
VIN = 5V 800 1500 Ω(max)
RON Multiplexer ON-Resistance VIN = 2.5V 850 1500 Ω(max)
VIN = 0V 760 1500 Ω(max)
LM12454
VIN = 5V ±1.0% ±3.0% (max)
Multiplexer Channel-to-Channel
RON matching VIN = 2.5V ±1.0% ±3.0% (max)
VIN = 0V ±1.0% ±3.0% (max)
(1) Two on-chip diodes are tied to each analog input through a series resistor, as shown below. Input voltage magnitude up to 5V above
VA+ or 5V below GND will not damage the LM12454 or the LM12(H)458. However, errors in the A/D conversion can occur if these
diodes are forward biased by more than 100 mV. As an example, if VA+ is 4.5 VDC, full-scale input voltage must be 4.6 VDC to ensure
accurate conversions. See Figure 3
(2) VA+ and VD+ must be connected together to the same power supply voltage and bypassed with separate capacitors at each V+pin to
assure conversion/comparison accuracy.
(3) Accuracy is ensured when operating at fCLK = 5 MHz for the LM12454/8 and fCLK = 8 MHz for the LM12H458.
(4) Typical figures are at TA= 25°C and represent most likely parametric norm.
(5) Limits are to AOQL (Average Output Quality Level).
Copyright © 2004–2006, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: LM12454 LM12458 LM12H458
LM12454, LM12458, LM12H458
SNAS079A MAY 2004REVISED FEBRUARY 2006
www.ti.com
INTERNAL REFERENCE CHARACTERISTICS (1) (2)
The following specifications apply to the LM12454, LM12458, and LM12H458 for VA+=VD+ = 5V unless otherwise specified.
Boldface limits apply for TA= TJ= TMIN to TMAX; all other limits TA= TJ= 25°C. Typical Limits
Symbol Parameter Conditions Units
(3) (4)
VREFOUT Internal Reference Output Voltage 2.5 2.5 ±4% V (max)
Internal Reference Temperature
ΔVREF/ΔT 40 ppm/°C
Coefficient Sourcing (0 < IL+4 mA) 0.2 %/mA (max)
ΔREF/ΔILInternal Reference Load Regulation Sinking (1IIL < 0 mA) 1.2 %/mA (max)
ΔVREF Line Regulation 4.5V VA+5.5V 3 20 mV (max)
ISC Internal Reference Short Circuit Current VREFOUT = 0V 13 25 mA (max)
ΔVREF/Δt Long Term Stability 200 ppm/kHr
VA+=VD+ = 0V
tSU Internal Reference Start-Up Time 10 ms
5V, CL= 100 μF
(1) Two on-chip diodes are tied to each analog input through a series resistor, as shown below. Input voltage magnitude up to 5V above
VA+ or 5V below GND will not damage the LM12454 or the LM12(H)458. However, errors in the A/D conversion can occur if these
diodes are forward biased by more than 100 mV. As an example, if VA+ is 4.5 VDC, full-scale input voltage must be 4.6 VDC to ensure
accurate conversions. See Figure 3
(2) VA+ and VD+ must be connected together to the same power supply voltage and bypassed with separate capacitors at each V+pin to
assure conversion/comparison accuracy.
(3) Typical figures are at TA= 25°C and represent most likely parametric norm.
(4) Limits are to AOQL (Average Output Quality Level).
DIGITAL CHARACTERISTICS(1) (2)
The following specifications apply to the LM12454, LM12458, and LM12H458 for VA+=VD+ = 5V, unless otherwise specified.
Boldface limits apply for TA= TJ= TMIN to TMAX; all other limits TA= TJ= 25°C. Typical Limits
Symbol Parameter Conditions Units
(3) (4)
VIN(1) Logical “1” Input Voltage VA+=VD+ = 5.5V 2.0 V (min)
VIN(0) Logical “0” Input Voltage VA+=VD+ = 4.5V 0.8 V (max)
IIN(1) Logical “1” Input Current VIN = 5V 0.005 1.0 μA (max)
IIN(0) Logical “0” Input Current VIN = 0V 0.005 1.0 μA (max)
CIN D0–D15 Input Capacitance 6 pF
VA+=VD+ = 4.5V
VOUT(1) Logical “1” Output Voltage IOUT =360 μA2.4 V (min)
IOUT =10 μA4.25 V (min)
VA+=VD+ = 4.5V
VOUT(0) Logical “0” Output Voltage 0.4 V (max)
IOUT = 1.6 mA
VOUT = 0V 0.01 3.0 μA (max)
IOUT TRI-STATE®Output Leakage Current VOUT = 5V 0.01 3.0 μA (max)
(1) Two on-chip diodes are tied to each analog input through a series resistor, as shown below. Input voltage magnitude up to 5V above
VA+ or 5V below GND will not damage the LM12454 or the LM12(H)458. However, errors in the A/D conversion can occur if these
diodes are forward biased by more than 100 mV. As an example, if VA+ is 4.5 VDC, full-scale input voltage must be 4.6 VDC to ensure
accurate conversions. See Figure 3
(2) VA+ and VD+ must be connected together to the same power supply voltage and bypassed with separate capacitors at each V+pin to
assure conversion/comparison accuracy.
(3) Typical figures are at TA= 25°C and represent most likely parametric norm.
(4) Limits are to AOQL (Average Output Quality Level).
10 Submit Documentation Feedback Copyright © 2004–2006, Texas Instruments Incorporated
Product Folder Links: LM12454 LM12458 LM12H458
LM12454, LM12458, LM12H458
www.ti.com
SNAS079A MAY 2004REVISED FEBRUARY 2006
DIGITAL TIMING CHARACTERISTICS (1) (2) (3)
The following specifications apply to the LM12454, LM12458, and LM12H458 for VA+=VD+ = 5V, tr= tf= 3 ns, and CL= 100
pF on data I/O, INT and DMARQ lines unless otherwise specified. Boldface limits apply for TA= TJ= TMIN to TMAX; all other
limits TA= TJ= 25°C.
Symbol (See
Figure 7 Parameter Conditions Typical (4) Limits (5) Units
Figure 40
Figure 42)
1, 3 CS or Address Valid to ALE Low Set-Up Time 40 ns (min)
2, 4 CS or Address Valid to ALE Low Hold Time 20 ns (min)
5 ALE Pulse Width 45 ns (min)
6 RD High to Next ALE High 35 ns (min)
7 ALE Low to RD Low 20 ns (min)
8 RD Pulse Width 100 ns (min)
9 RD High to Next RD or WR Low 100 ns (min)
10 ALE Low to WR Low 20 ns (min)
11 WR Pulse Width 60 ns (min)
12 WR High to Next ALE High 75 ns (min)
13 WR High to Next RD or WR Low 140 ns (min)
14 Data Valid to WR High Set-Up Time 40 ns (min)
15 Data Valid to WR High Hold Time 30 ns (min)
10 ns (min)
16 RD Low to Data Bus Out of TRI-STATE 40 70 ns (max)
10 ns (min)
17 RD High to TRI-STATE RL= 1 kΩ30 110 ns (max)
10 ns (min)
18 RD Low to Data Valid (Access Time) 30 80 ns (max)
20 Address Valid or CS Low to RD Low 20 ns (min)
21 Address Valid or CS Low to WR Low 20 ns (min)
19 Address Invalid from RD or WR High 10 ns (min)
10 ns (min)
22 INT High from RD Low 30 60 ns (max)
10 ns (min)
23 DMARQ Low from RD Low 30 60 ns (max)
(1) Two on-chip diodes are tied to each analog input through a series resistor, as shown below. Input voltage magnitude up to 5V above
VA+ or 5V below GND will not damage the LM12454 or the LM12(H)458. However, errors in the A/D conversion can occur if these
diodes are forward biased by more than 100 mV. As an example, if VA+ is 4.5 VDC, full-scale input voltage must be 4.6 VDC to ensure
accurate conversions. See Figure 3
(2) VA+ and VD+ must be connected together to the same power supply voltage and bypassed with separate capacitors at each V+pin to
assure conversion/comparison accuracy.
(3) Accuracy is ensured when operating at fCLK = 5 MHz for the LM12454/8 and fCLK = 8 MHz for the LM12H458.
(4) Typical figures are at TA= 25°C and represent most likely parametric norm.
(5) Limits are to AOQL (Average Output Quality Level).
Figure 3.
Copyright © 2004–2006, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Links: LM12454 LM12458 LM12H458
LM12454, LM12458, LM12H458
SNAS079A MAY 2004REVISED FEBRUARY 2006
www.ti.com
VREF = VREF+ VREF
VIN = VIN+ VIN
GND VIN+ VA+
GND VINVA+
VREF+ VREF= 4.096V
VIN = VIN+ VIN
GND VIN+ VA+
GND VINVA+
VREF = VREF+ VREF
12 Submit Documentation Feedback Copyright © 2004–2006, Texas Instruments Incorporated
Product Folder Links: LM12454 LM12458 LM12H458
LM12454, LM12458, LM12H458
www.ti.com
SNAS079A MAY 2004REVISED FEBRUARY 2006
VREF = VREF+ VREF
VA+ = 5V
Figure 4. Transfer Characteristic
Copyright © 2004–2006, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Links: LM12454 LM12458 LM12H458
LM12454, LM12458, LM12H458
SNAS079A MAY 2004REVISED FEBRUARY 2006
www.ti.com
Figure 5. Simplified Error Curve vs. Output Code without Auto-Calibration or Auto-Zero Cycles
Figure 6. Simplified Error Curve vs. Output Code after Auto-Calibration Cycle
Figure 7. Offset or Zero Error Voltage
14 Submit Documentation Feedback Copyright © 2004–2006, Texas Instruments Incorporated
Product Folder Links: LM12454 LM12458 LM12H458
LM12454, LM12458, LM12H458
www.ti.com
SNAS079A MAY 2004REVISED FEBRUARY 2006
TYPICAL PERFORMANCE CHARACTERISTICS
(1)The following curves apply for 12-bit + sign mode after auto-calibration unless otherwise specified. The performance for 8-
bit + sign and “watchdog” modes is equal to or better than shown.
Linearity Error Change Linearity Error Change
vs. Clock Frequency vs. Temperature
Figure 8. Figure 9.
Linearity Error Change Linearity Error Change
vs. Reference Voltage vs. Supply Voltage
Figure 10. Figure 11.
Full-Scale Error Change Full-Scale Error Change
vs. Clock Frequency vs. Temperature
Figure 12. Figure 13.
(1) With the test condition for VREF (VREF+ VREF) given as +5V, the 12-bit LSB is 1.22 mV and the 8-bit/“Watchdog” LSB is 19.53 mV.
Copyright © 2004–2006, Texas Instruments Incorporated Submit Documentation Feedback 15
Product Folder Links: LM12454 LM12458 LM12H458
LM12454, LM12458, LM12H458
SNAS079A MAY 2004REVISED FEBRUARY 2006
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
(1) The following curves apply for 12-bit + sign mode after auto-calibration unless otherwise specified. The performance for 8-
bit + sign and “watchdog” modes is equal to or better than shown.
Full-Scale Error Change Full-Scale Error
vs. Reference Voltage vs. Supply Voltage
Figure 14. Figure 15.
Zero Error Change Zero Error Change
vs. Clock Frequency vs. Temperature
Figure 16. Figure 17.
Zero Error Change Zero Error Change
vs. Reference Voltage vs. Supply Voltage
Figure 18. Figure 19.
16 Submit Documentation Feedback Copyright © 2004–2006, Texas Instruments Incorporated
Product Folder Links: LM12454 LM12458 LM12H458
LM12454, LM12458, LM12H458
www.ti.com
SNAS079A MAY 2004REVISED FEBRUARY 2006
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
(1) The following curves apply for 12-bit + sign mode after auto-calibration unless otherwise specified. The performance for 8-
bit + sign and “watchdog” modes is equal to or better than shown.
Analog Supply Current Digital Supply Current
vs. Temperature vs. Clock Frequency
Figure 20. Figure 21.
Digital Supply Current
vs. Temperature VREFOUT Load Regulation
Figure 22. Figure 23.
VREFOUT Line Regulation
Figure 24.
Copyright © 2004–2006, Texas Instruments Incorporated Submit Documentation Feedback 17
Product Folder Links: LM12454 LM12458 LM12H458
LM12454, LM12458, LM12H458
SNAS079A MAY 2004REVISED FEBRUARY 2006
www.ti.com
TYPICAL DYNAMIC PERFORMANCE CHARACTERISTICS
The following curves apply for 12-bit + sign mode after auto-calibration unless otherwise specified.
Bipolar Signal-to-Noise
Bipolar Signal-to-Noise Ratio + Distortion Ratio
vs. Input Frequency vs. Input Frequency
Figure 25. Figure 26.
Bipolar Signal-to-Noise
+ Distortion Ratio Bipolar Spectral Response
vs. Input Signal Level with 1.028 kHz Sine Wave Input
Figure 27. Figure 28.
Bipolar Spectral Response Bipolar Spectral Response
with 10 kHz Sine Wave Input with 20 kHz Sine Wave Input
Figure 29. Figure 30.
18 Submit Documentation Feedback Copyright © 2004–2006, Texas Instruments Incorporated
Product Folder Links: LM12454 LM12458 LM12H458
LM12454, LM12458, LM12H458
www.ti.com
SNAS079A MAY 2004REVISED FEBRUARY 2006
TYPICAL DYNAMIC PERFORMANCE CHARACTERISTICS (continued)
The following curves apply for 12-bit + sign mode after auto-calibration unless otherwise specified.
Bipolar Spectral Response Bipolar Spurious Free
with 40 kHz Sine Wave Input Dynamic Range
Figure 31. Figure 32.
Unipolar Signal-to-Noise
Unipolar Signal-to-Noise Ratio + Distortion Ratio
vs. Input Frequency vs. Input Frequency
Figure 33. Figure 34.
Unipolar Signal-to-Noise
+ Distortion Ratio Unipolar Spectral Response
vs. Input Signal Level with 1.028 kHz Sine Wave Input
Figure 35. Figure 36.
Copyright © 2004–2006, Texas Instruments Incorporated Submit Documentation Feedback 19
Product Folder Links: LM12454 LM12458 LM12H458
LM12454, LM12458, LM12H458
SNAS079A MAY 2004REVISED FEBRUARY 2006
www.ti.com
TYPICAL DYNAMIC PERFORMANCE CHARACTERISTICS (continued)
The following curves apply for 12-bit + sign mode after auto-calibration unless otherwise specified.
Unipolar Spectral Response Unipolar Spectral Response
with 10 kHz Sine Wave Input with 20 kHz Sine Wave Input
Figure 37. Figure 38.
Unipolar Spectral Response
with 40 kHz Sine Wave Input
Figure 39.
TEST CIRCUITS and WAVEFORMS
Figure 40. TRI-STATE Test Circuits and Waveforms
20 Submit Documentation Feedback Copyright © 2004–2006, Texas Instruments Incorporated
Product Folder Links: LM12454 LM12458 LM12H458
LM12454, LM12458, LM12H458
www.ti.com
SNAS079A MAY 2004REVISED FEBRUARY 2006
Figure 41. TRI-STATE Test Circuits and Waveforms
TIMING DIAGRAMS
VA+=VD+ = +5V, tR= tF= 3 ns, CL= 100 pF for the INT, DMARQ, D0–D15 outputs.
Figure 42. Multiplexed Data Bus
1, 3: CS or Address valid to ALE low set-up time.
2, 4: CS or Address valid to ALE low hold time.
5: ALE pulse width
6: RD high to next ALE high
7: ALE low to RD low
8: RD pulse width
9: RD high to next RD or WR low
10: ALE low to WR low
11: WR pulse width
Copyright © 2004–2006, Texas Instruments Incorporated Submit Documentation Feedback 21
Product Folder Links: LM12454 LM12458 LM12H458
LM12454, LM12458, LM12H458
SNAS079A MAY 2004REVISED FEBRUARY 2006
www.ti.com
12: WR high to next ALE high
13: WR high to next WR or RD low
14: Data valid to WR high set-up time
15: Data valid to WR high hold time
16: RD low to data bus out of TRI-STATE
17: RD high to TRI-STATE
18: RD low to data valid (access time)
Figure 43. Non-Multiplexed Data Bus (ALE = 1)
8: RD pulse width
9: RD high to next RD or WR low
11: WR pulse width
13: WR high to next WR or RD low
14: Data valid to WR high set-up time
15: Data valid to WR high hold time
16: RD low to data bus out of TRI-STATE
17: RD high to TRI-STATE
18: RD low to data valid (access time)
19: Address invalid from RD or WR high (hold time)
20: CS low or address valid to RD low
21: CS low or address valid to WR low
VA+=VD+ = +5V, tR= tF= 3 ns, CL= 100 pF for the INT, DMARQ, D0–D15 outputs.
22 Submit Documentation Feedback Copyright © 2004–2006, Texas Instruments Incorporated
Product Folder Links: LM12454 LM12458 LM12H458
LM12454, LM12458, LM12H458
www.ti.com
SNAS079A MAY 2004REVISED FEBRUARY 2006
Figure 44. Interrupt and DMARQ
22: INT high from RD low
23: DMARQ low from RD low
Pin Descriptions
Analog and digital supply voltage pins. The LM12(H)454/8's supply voltage operating range is +3.0V to +5.5V.
Accuracy is ensured only if VA+ and VD+ are connected to the same power supply. Each pin should have a
VA+ VD+parallel combination of 10 µF (electrolytic or tantalum) and 0.1 µF (ceramic) bypass capacitors connected
between it and ground.
The internal data input/output TRI-STATE buffers are connected to these pins. These buffers are designed to
drive capacitive loads of 100 pF or less. External buffers are necessary for driving higher load capacitances.
These pins allows the user a means of instruction input and data output. With a logic high applied to the BW
D0–D15 pin, data lines D8–D15 are placed in a high impedance state and data lines D0–D7 are used for instruction
input and data output when the LM12(H)454/8 is connected to an 8-bit wide data bus. A logic low on the BW
pin allows the LM12(H)454/8 to exchange information over a 16-bit wide data bus.
Input for the active low READ bus control signal. The data input/output TRI-STATE buffers, as selected by the
RD logic signal applied to the BW pin, are enabled when RD and CS are both low. This allows the LM12(H)454/8
to transmit information onto the data bus.
Input for the active low WRITE bus control signal. The data input/output TRI-STATE buffers, as selected by the
WR logic signal applied to the BW pin, are enabled when WR and CS are both low. This allows the LM12(H)454/8
to receive information from the data bus.
Input for the active low Chip Select control signal. A logic low should be applied to this pin only during a READ
CS or WRITE access to the LM12(H)454/8. The internal clocking is halted and conversion stops while Chip Select
is low. Conversion resumes when the Chip Select input signal returns high.
Address Latch Enable input. It is used in systems containing a multiplexed data bus. When ALE is asserted
high, the LM12(H)454/8 accepts information on the data bus as a valid address. A high-to-low transition will
ALE latch the address data on A0–A4 while the CS is low. Any changes on A0–A4 and CS while ALE is low will not
affect the LM12(H)454/8. See Figure 42. When a non-multiplexed bus is used, ALE is continuously asserted
high. See Figure 43.
External clock input pin. The LM12(H)454/8 operates with an input clock frequency in the range of 0.05 MHz to
CLK 10.0 MHz.
The LM12(H)454/8's address lines. They are used to access all internal registers, Conversion FIFO, and
A0–A4 Instruction RAM.
Synchronization input/output. When used as an output, it is designed to drive capacitive loads of 100 pF or
less. External buffers are necessary for driving higher load capacitances. SYNC is an input if the Configuration
register's “I/O Select” bit is low. A rising edge on this pin causes the internal S/H to hold the input signal. The
next rising clock edge either starts a conversion or makes a comparison to a programmable limit depending on
SYNC which function is requested by a programming instruction. This pin will be an output if “I/O Select” is set high.
The SYNC output goes high when a conversion or a comparison is started and low when completed. (See
Section 2.2). An internal reset after power is first applied to the LM12(H)454/8 automatically sets this pin as an
input.
Bus Width input pin. This input allows the LM12(H)454/8 to interface directly with either an 8- or 16-bit data
BW bus. A logic high sets the width to 8 bits and places D8–D15 in a high impedance state. A logic low sets the
width to 16 bits.
Active low interrupt output. This output is designed to drive capacitive loads of 100 pF or less. External buffers
are necessary for driving higher load capacitances. An interrupt signal is generated any time a non-masked
INT interrupt condition takes place. There are eight different conditions that can cause an interrupt. Any interrupt is
reset by reading the Interrupt Status register. (See Section 2.3.)
Copyright © 2004–2006, Texas Instruments Incorporated Submit Documentation Feedback 23
Product Folder Links: LM12454 LM12458 LM12H458
LM12454, LM12458, LM12H458
SNAS079A MAY 2004REVISED FEBRUARY 2006
www.ti.com
Pin Descriptions (continued)
Active high Direct Memory Access Request output. This output is designed to drive capacitive loads of 100 pF
or less. External buffers are necessary for driving higher load capacitances. It goes high whenever the number
DMARQ of conversion results in the conversion FIFO equals a programmable value stored in the Interrupt Enable
register. It returns to a logic low when the FIFO is empty.
LM12(H)454/8 ground connection. It should be connected to a low resistance and inductance analog ground
GND return that connects directly to the system power supply ground.
The eight (LM12(H)458) or four (LM12454) analog inputs. A given channel is selected through the instruction
IN0–IN7 (IN0–IN3 RAM. Any of the channels can be configured as an independent single-ended input. Any pair of channels,
LM12H454 LM12454) whether adjacent or non-adjacent, can operate as a fully differential pair.
S/H IN+ S/H IN- The LM12454's non-inverting and inverting inputs to the internal S/H.
MUXOUT+ MUXOUT- The LM12454's non-inverting and inverting outputs from the internal multiplexer.
The negative reference input. The LM12(H)454/8 operate with 0V = VREF-= VREF+. This pin should be bypassed
VREF- to ground with a parallel combination of 10 µF and 0.1 µF (ceramic) capacitors.
The positive reference input. The LM12(H)454/8 operate with 0V = VREF+ = VA+. This pin should be bypassed
VREF+ to ground with a parallel combination of 10 µF and 0.1 µF (ceramic) capacitors.
VREFOUT The internal 2.5V bandgap's output pin. This pin should be bypassed to ground with a 100 µF capacitor.
FUNCTIONAL DESCRIPTION
The LM12454 and LM12(H)458 are multi-functional Data Acquisition Systems that include a fully differential 12-
bit-plus-sign self-calibrating analog-to-digital converter (ADC) with a two's-complement output format, an 8-
channel (LM12(H)458) or a 4-channel (LM12454) analog multiplexer, an internal 2.5V reference, a first-in-first-out
(FIFO) register that can store 32 conversion results, and an Instruction RAM that can store as many as eight
instructions to be sequentially executed. The LM12454 also has a differential multiplexer output and a differential
S/H input. All of this circuitry operates on only a single +5V power supply.
The LM12(H)454/8 have three modes of operation:
12-bit + sign with correction
8-bit + sign without correction
8-bit + sign comparison mode (“watchdog” mode)
The fully differential 12-bit-plus-sign ADC uses a charge redistribution topology that includes calibration
capabilities. Charge re-distribution ADCs use a capacitor ladder in place of a resistor ladder to form an internal
DAC. The DAC is used by a successive approximation register to generate intermediate voltages between the
voltages applied to VREFand VREF+. These intermediate voltages are compared against the sampled analog
input voltage as each bit is generated. The number of intermediate voltages and comparisons equals the ADC's
resolution. The correction of each bit's accuracy is accomplished by calibrating the capacitor ladder used in the
ADC.
Two different calibration modes are available; one compensates for offset voltage, or zero error, while the other
corrects both offset error and the ADC's linearity error.
When correcting offset only, the offset error is measured once and a correction coefficient is created. During the
full calibration, the offset error is measured eight times, averaged, and a correction coefficient is created. After
completion of either calibration mode, the offset correction coefficient is stored in an internal offset correction
register.
The LM12(H)454/8's overall linearity correction is achieved by correcting the internal DAC's capacitor mismatch.
Each capacitor is compared eight times against all remaining smaller value capacitors and any errors are
averaged. A correction coefficient is then created and stored in one of the thirteen internal linearity correction
registers. An internal state machine, using patterns stored in an internal 16 x 8-bit ROM, executes each
calibration algorithm.
Once calibrated, an internal arithmetic logic unit (ALU) uses the offset correction coefficient and the 13 linearity
correction coefficients to reduce the conversion's offset error and linearity error, in the background, during the 12-
bit + sign conversion. The 8-bit + sign conversion and comparison modes use only the offset coefficient. The 8-
bit + sign mode performs a conversion in less than half the time used by the 12-bit + sign conversion mode.
24 Submit Documentation Feedback Copyright © 2004–2006, Texas Instruments Incorporated
Product Folder Links: LM12454 LM12458 LM12H458
LM12454, LM12458, LM12H458
www.ti.com
SNAS079A MAY 2004REVISED FEBRUARY 2006
The LM12(H)454/8's “watchdog” mode is used to monitor a single-ended or differential signal's amplitude. Each
sampled signal has two limits. An interrupt can be generated if the input signal is above or below either of the
two limits. This allows interrupts to be generated when analog voltage inputs are “inside the window” or,
alternatively, “outside the window”. After a “watchdog” mode interrupt, the processor can then request a
conversion on the input signal and read the signal's magnitude.
The analog input multiplexer can be configured for any combination of single-ended or fully differential operation.
Each input is referenced to ground when a multiplexer channel operates in the single-ended mode. Fully
differential analog input channels are formed by pairing any two channels together.
The LM12454's multiplexer outputs and S/H inputs (MUXOUT+, MUXOUTand S/H IN+, S/H IN) provide the
option for additional analog signal processing. Fixed-gain amplifiers, programmable-gain amplifiers, filters, and
other processing circuits can operate on the signal applied to the selected multiplexer channel(s). If external
processing is not used, connect MUXOUT+ to S/H IN+ and MUXOUTto S/H IN.
The LM12(H)454/8's internal S/H is designed to operate at its minimum acquisition time (1.13 μs, 12 bits) when
the source impedance, RS, is 60Ω(fCLK 8 MHz). When 60Ω< RS4.17 kΩ, the internal S/H's acquisition
time can be increased to a maximum of 4.88 μs (12 bits, fCLK = 8 MHz). See Section 2.1 (Instruction RAM “00”)
Bits 12–15 for more information.
An internal 2.5V bandgap reference output is available at pin 44. This voltage can be used as the ADC reference
for ratiometric conversion or as a virtual ground for front-end analog conditioning circuits. The VREFOUT pin should
be bypassed to ground with a 100 μF capacitor.
Microprocessor overhead is reduced through the use of the internal conversion FIFO. Thirty-two consecutive
conversions can be completed and stored in the FIFO without any microprocessor intervention. The
microprocessor can, at any time, interrogate the FIFO and retrieve its contents. It can also wait for the
LM12(H)454/8 to issue an interrupt when the FIFO is full or after any number (32) of conversions have been
stored.
Conversion sequencing, internal timer interval, multiplexer configuration, and many other operations are
programmed and set in the Instruction RAM.
A diagnostic mode is available that allows verification of the LM12(H)458's operation. The diagnostic mode is
disabled in the LM12454. This mode internally connects the voltages present at the VREFOUT, VREF+, VREF, and
GND pins to the internal VIN+ and VINS/H inputs. This mode is activated by setting the Diagnostic bit (Bit 11) in
the Configuration register to a “1”. More information concerning this mode of operation can be found in Section
2.2.
Internal User-Programmable Registers
INSTRUCTION RAM
The instruction RAM holds up to eight sequentially executable instructions. Each 48-bit long instruction is divided
into three 16-bit sections. READ and WRITE operations can be issued to each 16-bit section using the
instruction's address and the 2-bit “RAM pointer” in the Configuration register. The eight instructions are located
at addresses 0000 through 0111 (A4–A1, BW = 0) when using a 16-bit wide data bus or at addresses 00000
through 01111 (A4–A0, BW = 1) when using an 8-bit wide data bus. They can be accessed and programmed in
random order.
Any Instruction RAM READ or WRITE can affect the sequencer's operation:
The Sequencer should be stopped by setting the RESET bit to a “1” or by resetting the START bit in the
Configuration Register and waiting for the current instruction to finish execution before any Instruction
RAM READ or WRITE is initiated. Bit 0 of the Configuration Register indicates the Sequencer Status. See
paragraph 2.2 for information on the Configuration Register.
A soft RESET should be issued by writing a “1” to the Configuration Register's RESET bit after any READ
or WRITE to the Instruction RAM.
Copyright © 2004–2006, Texas Instruments Incorporated Submit Documentation Feedback 25
Product Folder Links: LM12454 LM12458 LM12H458
LM12454, LM12458, LM12H458
SNAS079A MAY 2004REVISED FEBRUARY 2006
www.ti.com
The three sections in the Instruction RAM are selected by the Configuration Register's 2-bit “RAM Pointer”, bits
D8 and D9. The first 16-bit Instruction RAM section is selected with the RAM Pointer equal to “00”. This section
provides multiplexer channel selection, as well as resolution, acquisition time, etc. The second 16-bit section
holds “watchdog” limit #1, its sign, and an indicator that shows that an interrupt can be generated if the input
signal is greater or less than the programmed limit. The third 16-bit section holds “watchdog” limit #2, its sign,
and an indicator that shows that an interrupt can be generated if the input signal is greater or less than the
programmed limit.
Instruction RAM “00”
Bit 0 is the LOOP bit. It indicates the last instruction to be executed in any instruction sequence when it is set to
a “1”. The next instruction to be executed will be instruction 0.
Bit 1 is the PAUSE bit. This controls the Sequencer's operation. When the PAUSE bit is set (“1”), the Sequencer
will stop after reading the current instruction and before executing it, and the start bit in the Configuration register
is automatically reset to a “0”. Setting the PAUSE also causes an interrupt to be issued. The Sequencer is
restarted by placing a “1” in the Configuration register's Bit 0 (Start bit).
After the Instruction RAM has been programmed and the RESET bit is set to “1”, the Sequencer retrieves
Instruction 000, decodes it, and waits for a “1” to be placed in the Configuration's START bit. The START bit
value of “0” “overrides” the action of Instruction 000's PAUSE bit when the Sequencer is started. Once started,
the Sequencer executes Instruction 000 and retrieves, decodes, and executes each of the remaining instructions.
No PAUSE Interrupt (INT 5) is generated the first time the Sequencer executes Instruction 000 having a PAUSE
bit set to “1”. When the Sequencer encounters a LOOP bit or completes all eight instructions, Instruction 000 is
retrieved and decoded. A set PAUSE bit in Instruction 000 now halts the Sequencer before the instruction is
executed.
Bits 2–4 select which of the eight input channels (“000” to “111” for IN0–IN7) will be configured as non-inverting
inputs to the LM12(H)458's ADC. (See Table 3.) They select which of the four input channels (“000” to “011” for
IN0–IN4) will be configured as non-inverting inputs to the LM12454's ADC. (See Table 4.)
Bits 5–7 select which of the seven input channels (“001” to “111” for IN1 to IN7) will be configured as inverting
inputs to the LM12(H)458's ADC. (See Table 3.) They select which of the three input channels (“001” to “011” for
IN1–IN4) will be configured as inverting inputs to the LM12454's ADC. (See Table 4.) Fully differential operation
is created by selecting two multiplexer channels, one operating in the non-inverting mode and the other operating
in the inverting mode. A code of “000” selects ground as the inverting input for single ended operation.
Bit 8 is the SYNC bit. Setting Bit 8 to “1” causes the Sequencer to suspend operation at the end of the internal
S/H's acquisition cycle and to wait until a rising edge appears at the SYNC pin. When a rising edge appears, the
S/H acquires the input signal magnitude and the ADC performs a conversion on the clock's next rising edge.
When the SYNC pin is used as an input, the Configuration register's “I/O Select” bit (Bit 7) must be set to a “0”.
With SYNC configured as an input, it is possible to synchronize the start of a conversion to an external event.
This is useful in applications such as digital signal processing (DSP) where the exact timing of conversions is
important.
When the LM12(H)454/8 are used in the “watchdog” mode with external synchronization, two rising edges on the
SYNC input are required to initiate two comparisons. The first rising edge initiates the comparison of the selected
analog input signal with Limit #1 (found in Instruction RAM “01”) and the second rising edge initiates the
comparison of the same analog input signal with Limit #2 (found in Instruction RAM “10”).
Bit 9 is the TIMER bit. When Bit 9 is set to “1”, the Sequencer will halt until the internal 16-bit Timer counts down
to zero. During this time interval, no “watchdog” comparisons or analog-to-digital conversions will be performed.
Bit 10 selects the ADC conversion resolution. Setting Bit 10 to “1” selects 8-bit + sign and when reset to “0”
selects 12-bit + sign.
Bit 11 is the “watchdog” comparison mode enable bit. When operating in the “watchdog” comparison mode, the
selected analog input signal is compared with the programmable values stored in Limit #1 and Limit #2 (see
Instruction RAM “01” and Instruction RAM “10”). Setting Bit 11 to “1” causes two comparisons of the selected
analog input signal with the two stored limits. When Bit 11 is reset to “0”, an 8-bit + sign or 12-bit + sign
(depending on the state of Bit 10 of Instruction RAM “00”) conversion of the input signal can take place.
26 Submit Documentation Feedback Copyright © 2004–2006, Texas Instruments Incorporated
Product Folder Links: LM12454 LM12458 LM12H458
LM12454, LM12458, LM12H458
www.ti.com
SNAS079A MAY 2004REVISED FEBRUARY 2006
Table 1. LM12(H)454/8 Memory Map for 16-Bit Wide Data Bus (BW = “0”, Test Bit = “0” and A0 = Don't Care)
A4 A3 A2 A1 Purpo Type D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0
se
0 0 0 Instruc
tion
0 to RAM Watch
R/W Acquisition Time 8/12 Timer Sync VIN(MUXOUT)(1) VIN+ (MUXOUT+) (1) Pause Loop
(RAM - dog
111Pointe
r = 00)
0 0 0 Instruc
tion
0 to RAM R/W Don't Care >/< Sign Limit #1
111(RAM
Pointe
r = 01)
0 0 0 Instruc
tion
0 to RAM R/W Don't Care >/< Sign Limit #2
111(RAM
Pointe
r = 10)
Config
uration DIAG * Test = Auto Char Stand- Full Auto-
1 0 0 0 R/W Don't Care RAM Pointer i/O Sel Reset Start
Regist (2) 0 Zeroec Mask by CAL Zero
er
Interru
pt Number of Conversions in Conversion Sequencer Address to
1 0 0 1 Enable R/W INT7 INT6 INT5 INT4 INT3 INT2 INT1 INT0
FIFO to Generate INT2 Generate INT1
Regist
er
Interru
pt Address of Sequencer
Actual Number of Conversion Results in
1 0 1 0 Status R Instruction being INST7 INST6 INST5 INST4 INST3 INST2 INST1 INST0
Conversion FIFO
Regist Executed
er
Timer R/W
1 0 1 1 Regist Timer Preset High Byte Timer Preset Low Byte
er
Conve
1 1 0 0 rsion R Address or Sign Sign Conversion Data: MSBs Conversion Data: LSBs
FIFO
Limit
Status
1 1 0 1 R Limit #2: Status Limit #1: Status
Regist
er
(1) LM12454 (Refer to Table 4).
(2) LM12(H)458 only. Must be set to “0” for the LM12454.
Copyright © 2004–2006, Texas Instruments Incorporated Submit Documentation Feedback 27
Product Folder Links: LM12454 LM12458 LM12H458
LM12454, LM12458, LM12H458
SNAS079A MAY 2004REVISED FEBRUARY 2006
www.ti.com
Table 2. LM12(H)454/8 Memory Map for 8-Bit Wide Data Bus (BW = “1” and Test Bit = “0”)
A4 A3 A2 A1 A0 Purpose Type D7 D6 D5 D4 D3 D2 D1 D0
0 0 0 VIN(MUXOUT) VIN+ (MUXOUT+)
0 to 0 R/W Pause Loop
Instruction (1) (1)
RAM
1 1 1 (RAM
0 0 0 Pointer =
00)
0 to 1 R/W Acquisition Time Watch- dog 8/12 Timer Sync
1 1 1
0 0 0 R/W Comparison Limit #1
Instruction RAM
0 to 0 (RAM Pointer = 01)
1 1 1 R/W Don't Care >/< Sign
0 0 0
0 to 1 R/W Don't Care >/< Sign
1 1 1
0 0 0
0 to 0 R/W Comparison Limit #2
Instruction
RAM
1 1 1 (RAM
0 0 0 Pointer =
10)
0 to 1 R/W Don't Care >/< Sign
1 1 1
1 0 0 0 0 R/W I/O Sel Auto Zeroec Chan Mask Stand- by Full Cal Auto- Zero Reset Start
Configuration
Register
1 0 0 0 1 R/W Don't Care DIAG (2) Test = 0 RAM Pointer
1 0 0 1 0 Interrupt R/W INT7 INT6 INT5 INT4 INT3 INT2 INT1 INT0
Enable
1 0 0 1 1 R/W Number of Conversions in Conversion FIFO to Generate INT2 Sequencer Address to Generate INT1
Register
1 0 1 0 0 Interrupt R INST7 INST6 INST5 INST4 INST3 INST2 INST1 INST0
Status
1 0 1 0 1 R Actual Number of Conversions Results in Conversion FIFO Address of Sequencer Instruction being Executed
Register
1 0 1 1 0 R/W Timer Preset: Low Byte
Timer
Register
1 0 1 1 1 R/W Timer Preset: High Byte
1 1 0 0 0 R Conversion Data: LSBs
Conversion
FIFO
1 1 0 0 1 R Address or Sign Sign Conversion Data: MSBs
1 1 0 1 0 R Limit #1 Status
Limit Status
Register
1 1 0 1 1 R Limit #2 Status
(1) LM12454 (Refer toTable 4).
(2) LM12(H)458 only. Must be set to “0” for the LM12454.
28 Submit Documentation Feedback Copyright © 2004–2006, Texas Instruments Incorporated
Product Folder Links: LM12454 LM12458 LM12H458
LM12454, LM12458, LM12H458
www.ti.com
SNAS079A MAY 2004REVISED FEBRUARY 2006
Bits 12–15 are used to store the user-programmable acquisition time. The Sequencer keeps the internal S/H in
the acquisition mode for a fixed number of clock cycles (nine clock cycles, for 12-bit + sign conversions and two
clock cycles for 8-bit + sign conversions or “watchdog” comparisons) plus a variable number of clock cycles
equal to twice the value stored in Bits 12–15. Thus, the S/H's acquisition time is (9 + 2D) clock cycles for 12-bit +
sign conversions and (2 + 2D) clock cycles for 8-bit + sign conversions or “watchdog” comparisons, where D is
the value stored in Bits 12–15. The minimum acquisition time compensates for the typical internal multiplexer
series resistance of 2 kΩ, and any additional delay created by Bits 12–15 compensates for source resistances
greater than 60Ω(100Ω). (For this acquisition time discussion, numbers in ( ) are shown for the LM12(H)454/8
operating at 5 MHz.) The necessary acquisition time is determined by the source impedance at the multiplexer
input. If the source resistance (RS) < 60Ω(100Ω) and the clock frequency is 8 MHz, the value stored in bits
12–15 (D) can be 0000. If RS> 60Ω(100Ω), the following equations determine the value that should be stored in
bits 12–15.
D = 0.45 x RSx fCLK (1)
for 12-bits + sign
D = 0.36 x RSx fCLK (2)
for 8-bits + sign and “watchdog”
RSis in kΩand fCLK is in MHz. Round the result to the next higher integer value. If D is greater than 15, it is
advisable to lower the source impedance by using an analog buffer between the signal source and the
LM12(H)458's multiplexer inputs. The value of D can also be used to compensate for the settling or response
time of external processing circuits connected between the LM12454's MUXOUT and S/H IN pins.
Instruction RAM “01”
The second Instruction RAM section is selected by placing a “01” in Bits 8 and 9 of the Configuration register.
Bits 0–7 hold “watchdog” limit #1. When Bit 11 of Instruction RAM “00” is set to a “1”, the LM12(H)454/8
performs a “watchdog” comparison of the sampled analog input signal with the limit #1 value first, followed by a
comparison of the same sampled analog input signal with the value found in limit #2 (Instruction RAM “10”).
Bit 8 holds limit #1's sign.
Bit 9's state determines the limit condition that generates a “watchdog” interrupt. A “1” causes a voltage greater
than limit #1 to generate an interrupt, while a “0” causes a voltage less than limit #1 to generate an interrupt.
Bits 10–15 are not used.
Instruction RAM “10”
The third Instruction RAM section is selected by placing a “10” in Bits 8 and 9 of the Configuration register.
Bits 0–7 hold “watchdog” limit #2. When Bit 11 of Instruction RAM “00” is set to a “1”, the LM12(H)454/8
performs a “watchdog” comparison of the sampled analog input signal with the limit #1 value first (Instruction
RAM “01”), followed by a comparison of the same sampled analog input signal with the value found in limit #2.
Bit 8 holds limit #2's sign.
Bit 9 's state determines the limit condition that generates a “watchdog” interrupt. A “1” causes a voltage greater
than limit #2 to generate an interrupt, while a “0” causes a voltage less than limit #2 to generate an interrupt.
Bits 10–15 are not used.
CONFIGURATION REGISTER
The Configuration register, 1000 (A4–A1, BW = 0) or 1000x (A4–A0, BW = 1) is a 16-bit control register with
read/write capability. It acts as the LM12454's and LM12(H)458's “control panel” holding global information as
well as start/stop, reset, self-calibration, and stand-by commands.
Bit 0 is the START/STOP bit. Reading Bit 0 returns an indication of the Sequencer's status. A “0” indicates that
the Sequencer is stopped and waiting to execute the next instruction. A “1” shows that the Sequencer is running.
Writing a “0” halts the Sequencer when the current instruction has finished execution. The next instruction to be
executed is pointed to by the instruction pointer found in the status register. A “1” restarts the Sequencer with the
instruction currently pointed to by the instruction pointer. (See Bits 8–10 in the Interrupt Status register.)
Copyright © 2004–2006, Texas Instruments Incorporated Submit Documentation Feedback 29
Product Folder Links: LM12454 LM12458 LM12H458
LM12454, LM12458, LM12H458
SNAS079A MAY 2004REVISED FEBRUARY 2006
www.ti.com
Bit 1 is the LM12(H)454/8's system RESET bit. Writing a “1” to Bit 1 stops the Sequencer (resetting the
Configuration register's START/STOP bit), resets the Instruction pointer to “000” (found in the Interrupt Status
register), clears the Conversion FIFO, and resets all interrupt flags. The RESET bit will return to “0” after two
clock cycles unless it is forced high by writing a “1” into the Configuration register's Standby bit. A reset signal is
internally generated when power is first applied to the part. No operation should be started until the RESET bit is
“0”.
Writing a “1” to Bit 2 initiates an auto-zero offset voltage calibration. Unlike the eight-sample auto-zero calibration
performed during the full calibration procedure, Bit 2 initiates a “short” auto-zero by sampling the offset once and
creating a correction coefficient (full calibration averages eight samples of the converter offset voltage when
creating a correction coefficient). If the Sequencer is running when Bit 2 is set to “1”, an auto-zero starts
immediately after the conclusion of the currently running instruction. Bit 2 is reset automatically to a “0” and an
interrupt flag (Bit 3, in the Interrupt Status register) is set at the end of the auto-zero (76 clock cycles). After
completion of an auto-zero calibration, the Sequencer fetches the next instruction as pointed to by the Instruction
RAM's pointer and resumes execution. If the Sequencer is stopped, an auto-zero is performed immediately at the
time requested.
Writing a “1” to Bit 3 initiates a complete calibration process that includes a “long” auto-zero offset voltage
correction (this calibration averages eight samples of the comparator offset voltage when creating a correction
coefficient) followed by an ADC linearity calibration. This complete calibration is started after the currently
running instruction is completed if the Sequencer is running when Bit 3 is set to “1”. Bit 3 is reset automatically to
a “0” and an interrupt flag (Bit 4, in the Interrupt Status register) will be generated at the end of the calibration
procedure (4944 clock cycles). After completion of a full auto-zero and linearity calibration, the Sequencer
fetches the next instruction as pointed to by the Instruction RAM's pointer and resumes execution. If the
Sequencer is stopped, a full calibration is performed immediately at the time requested.
Bit 4 is the Standby bit. Writing a “1” to Bit 4 immediately places the LM12(H)454/8 in Standby mode. Normal
operation returns when Bit 4 is reset to a “0”. The Standby command (“1”) disconnects the external clock from
the internal circuitry, decreases the LM12(H)454/8's internal analog circuitry power supply current, and preserves
all internal RAM contents. After writing a “0” to the Standby bit, the LM12(H)454/8 returns to an operating state
identical to that caused by exercising the RESET bit. A Standby completion interrupt is issued after a power-up
completion delay that allows the analog circuitry to settle. The Sequencer should be restarted only after the
Standby completion is issued. The Instruction RAM can still be accessed through read and write operations while
the LM12(H)454/8 are in Standby Mode.
Bit 5 is the Channel Address Mask. If Bit 5 is set to a “1”, Bits 13–15 in the conversion FIFO will be equal to the
sign bit (Bit 12) of the conversion data. Resetting Bit 5 to a “0” causes conversion data Bits 13 through 15 to hold
the instruction pointer value of the instruction to which the conversion data belongs.
Bit 6 is used to select a “short” auto-zero correction for every conversion. The Sequencer automatically inserts
an auto-zero before every conversion or “watchdog” comparison if Bit 6 is set to “1”. No automatic correction will
be performed if Bit 6 is reset to “0”.
The LM12(H)454/8's offset voltage, after calibration, has a typical drift of 0.1 LSB over a temperature range of
40°C to +85°C. This small drift is less than the variability of the change in offset that can occur when using the
auto-zero correction with each conversion. This variability is the result of using only one sample of the offset
voltage to create a correction value. This variability decreases when using the full calibration mode because eight
samples of the offset voltage are taken, averaged, and used to create a correction value.
Bit 7 is used to program the SYNC pin (29) to operate as either an input or an output. The SYNC pin becomes
an output when Bit 7 is a “1” and an input when Bit 7 is a “0”. With SYNC programmed as an input, the rising
edge of any logic signal applied to pin 29 will start a conversion or “watchdog” comparison. Programmed as an
output, the logic level at pin 29 will go high at the start of a conversion or “watchdog” comparison and remain
high until either have finished. See Instruction RAM “00”, Bit 8.
Bits 8 and 9form the RAM Pointer that is used to select each of a 48-bit instruction's three 16-bit sections during
read or write actions. A “00” selects Instruction RAM section one, “01” selects section two, and “10” selects
section three.
Bit 10 activates the Test mode that is used only during production testing. Leave this bit reset to “0”.
30 Submit Documentation Feedback Copyright © 2004–2006, Texas Instruments Incorporated
Product Folder Links: LM12454 LM12458 LM12H458
LM12454, LM12458, LM12H458
www.ti.com
SNAS079A MAY 2004REVISED FEBRUARY 2006
Bit 11 is the Diagnostic bit and is available only in the LM12(H)458. It can be activated by setting it to a “1” (the
Test bit must be reset to a “0”). The Diagnostic mode, along with a correctly chosen instruction, allows
verification that the LM12(H)458's ADC is performing correctly. When activated, the inverting and non-inverting
inputs are connected as shown in Table 3. As an example, an instruction with “001” for both VIN+ and VINwhile
using the Diagnostic mode typically results in a full-scale output.
INTERRUPTS
The LM12454 and LM12(H)458 have eight possible interrupts, all with the same priority. Any of these interrupts
will cause a hardware interrupt to appear on the INT pin (31) if they are not masked (by the Interrupt Enable
register). The Interrupt Status register is then read to determine which of the eight interrupts has been issued.
Table 3. LM12(H)458 Input Multiplexer
Channel Configuration Showing Normal
Mode and Diagnostic Mode
Channel Normal Mode Diagnostic Mode
Selection VIN+ VINVIN+ VIN
Data
000 IN0 GND VREFOUT GND
001 IN1 IN1 VREF+ VREF
010 IN2 IN2 IN2 IN2
011 IN3 IN3 IN3 IN3
100 IN4 IN4 IN4 IN4
101 IN5 IN5 IN5 IN5
110 IN6 IN6 IN6 IN6
111 IN7 IN7 IN7 IN7
Table 4. LM12454 Input Multiplexer
Channel Configuration
Channel Selection Data MUX+ MUX
000 IN0 GND
001 IN1 IN1
010 IN2 IN2
011 IN3 IN3
1XX OPEN OPEN
NOTE: The LM12(H)454 is no longer available. Information shown for reference only.
The Interrupt Status register, 1010 (A4–A1, BW = 0) or 1010x (A4–A0, BW = 1) must be cleared by reading it
after writing to the Interrupt Enable register. This removes any spurious interrupts on the INT pin generated
during an Interrupt Enable register access.
Interrupt 0 is generated whenever the analog input voltage on a selected multiplexer channel crosses a limit
while the LM12(H)454/8 are operating in the “watchdog” comparison mode. Two sequential comparisons are
made when the LM12(H)454/8 are executing a “watchdog” instruction. Depending on the logic state of Bit 9 in
the Instruction RAM's second and third sections, an interrupt will be generated either when the input signal's
magnitude is greater than or less than the programmable limits. (See the Instruction RAM, Bit 9 description.) The
Limit Status register will indicate which preprogrammed limit, #1 or #2 and which instruction was executing when
the limit was crossed.
Interrupt 1 is generated when the Sequencer reaches the instruction counter value specified in the Interrupt
Enable register's bits 8–10. This flag appears before the instruction's execution.
Interrupt 2 is activated when the Conversion FIFO holds a number of conversions equal to the programmable
value stored in the Interrupt Enable register's Bits 11–15. This value ranges from 0001 to 1111, representing 1 to
31 conversions stored in the FIFO. A user-programmed value of 0000 has no meaning. See Section 3.0 for more
FIFO information.
The completion of the short, single-sample auto-zero calibration generates Interrupt 3.
Copyright © 2004–2006, Texas Instruments Incorporated Submit Documentation Feedback 31
Product Folder Links: LM12454 LM12458 LM12H458
LM12454, LM12458, LM12H458
SNAS079A MAY 2004REVISED FEBRUARY 2006
www.ti.com
The completion of a full auto-zero and linearity self-calibration generates Interrupt 4.
Interrupt 5 is generated when the Sequencer encounters an instruction that has its Pause bit (Bit 1 in Instruction
RAM “00”) set to “1”.
The LM12(H)454/8 issues Interrupt 6 whenever it senses that its power supply voltage is dropping below 4V
(typ). This interrupt indicates the potential corruption of data returned by the LM12(H)454/8.
Interrupt 7 is issued after a short delay (10 ms typ) while the LM12(H)454/8 returns from Standby mode to active
operation using the Configuration register's Bit 4. This short delay allows the internal analog circuitry to settle
sufficiently, ensuring accurate conversion results.
INTERRUPT ENABLE REGISTER
The Interrupt Enable register at address location 1001 (A4–A1, BW = 0) or 1001x (A4–A0, BW = 1) has
READ/WRITE capability. An individual interrupt's ability to produce an external interrupt at pin 31 (INT) is
accomplished by placing a “1” in the appropriate bit location. Any of the internal interrupt-producing operations
will set their corresponding bits to “1” in the Interrupt Status register regardless of the state of the associated bit
in the Interrupt Enable register. See Section 2.3 for more information about each of the eight internal interrupts.
Bit 0 enables an external interrupt when an internal “watchdog” comparison limit interrupt has taken place.
Bit 1 enables an external interrupt when the Sequencer has reached the address stored in Bits 8–10 of the
Interrupt Enable register.
Bit 2 enables an external interrupt when the Conversion FIFO's limit, stored in Bits 11–15 of the Interrupt Enable
register, has been reached.
Bit 3 enables an external interrupt when the single-sample auto-zero calibration has been completed.
Bit 4 enables an external interrupt when a full auto-zero and linearity self-calibration has been completed.
Bit 5 enables an external interrupt when an internal Pause interrupt has been generated.
Bit 6 enables an external interrupt when a low power supply condition (VA+ < 4V) has generated an internal
interrupt.
Bit 7 enables an external interrupt when the LM12(H)454/8 return from power-down to active mode.
Bits 8 10 form the storage location of the user-programmable value against which the Sequencer's address is
compared. When the Sequencer reaches an address that is equal to the value stored in Bits 8–10, an internal
interrupt is generated and appears in Bit 1 of the Interrupt Status register. If Bit 1 of the Interrupt Enable register
is set to “1”, an external interrupt will appear at pin 31 (INT).
The value stored in bits 8–10 ranges from 000 to 111, representing 0 to 7 instructions stored in the Instruction
RAM. After the Instruction RAM has been programmed and the RESET bit is set to “1”, the Sequencer is started
by placing a “1” in the Configuration register's START bit. Setting the INT 1 trigger value to 000 does not
generate an INT 1 the first time the Sequencer retrieves and decodes Instruction 000. The Sequencer
generates INT 1 (by placing a “1” in the Interrupt Status register's Bit 1) the second time and after the
Sequencer encounters Instruction 000. It is important to remember that the Sequencer continues to operate even
if an Instruction interrupt (INT 1) is internally or externally generated. The only mechanisms that stop the
Sequencer are an instruction with the PAUSE bit set to “1” (halts before instruction execution), placing a “0” in
the Configuration register's START bit, or placing a “1” in the Configuration register's RESET bit.
Bits 11–15 hold the number of conversions that must be stored in the Conversion FIFO in order to generate an
internal interrupt. This internal interrupt appears in Bit 2 of the Interrupt Status register. If Bit 2 of the Interrupt
Enable register is set to “1”, an external interrupt will appear at pin 31 (INT).
Other Registers and Functions
INTERRUPT STATUS REGISTER
This read-only register is located at address 1010 (A4–A1, BW = 0) or 1010x (A4–A0, BW = 1). The
corresponding flag in the Interrupt Status register goes high (“1”) any time that an interrupt condition takes place,
whether an interrupt is enabled or disabled in the Interrupt Enable register. Any of the active (“1”) Interrupt Status
register flags are reset to “0” whenever this register is read or a device reset is issued (see Bit 1 in the
Configuration Register).
32 Submit Documentation Feedback Copyright © 2004–2006, Texas Instruments Incorporated
Product Folder Links: LM12454 LM12458 LM12H458
LM12454, LM12458, LM12H458
www.ti.com
SNAS079A MAY 2004REVISED FEBRUARY 2006
Bit 0 is set to “1” when a “watchdog” comparison limit interrupt has taken place.
Bit 1 is set to “1” when the Sequencer has reached the address stored in Bits 8–10 of the Interrupt Enable
register.
Bit 2 is set to “1” when the Conversion FIFO's limit, stored in Bits 11–15 of the Interrupt Enable register, has
been reached.
Bit 3 is set to “1” when the single-sample auto-zero has been completed.
Bit 4 is set to “1” when an auto-zero and full linearity self-calibration has been completed.
Bit 5 is set to “1” when a Pause interrupt has been generated.
Bit 6 is set to “1” when a low-supply voltage condition (VA+ < 4V) has taken place.
Bit 7 is set to “1” when the LM12(H)454/8 return from power-down to active mode.
Bits 8–10 hold the Sequencer's actual instruction address while it is running.
Bits 11–15 hold the actual number of conversions stored in the Conversion FIFO while the Sequencer is running.
LIMIT STATUS REGISTER
The read-only register is located at address 1101 (A4–A1, BW = 0) or 1101x (A4–A0, BW = 1). This register is
used in tandem with the Limit #1 and Limit #2 registers in the Instruction RAM. Whenever a given instruction's
input voltage exceeds the limit set in its corresponding Limit register (#1 or #2), a bit, corresponding to the
instruction number, is set in the Limit Status register. Any of the active (“1”) Limit Status flags are reset to “0”
whenever this register is read or a device reset is issued (see Bit 1 in the Configuration register). This register
holds the status of limits #1 and #2 for each of the eight instructions.
Bits 0–7 show the Limit #1 status. Each bit will be set high (“1”) when the corresponding instruction's input
voltage exceeds the threshold stored in the instruction's Limit #1 register. When, for example, instruction 3 is a
“watchdog” operation (Bit 11 is set high) and the input for instruction 3 meets the magnitude and/or polarity data
stored in instruction 3's Limit #1 register, Bit 3 in the Limit Status register will be set to a “1”.
Bits 8–15 show the Limit #2 status. Each bit will be set high (“1”) when the corresponding instruction's input
voltage exceeds the threshold stored in the instruction's Limit #2 register. When, for example, the input to
instruction 6 meets the value stored in instruction 6's Limit #2 register, Bit 14 in the Limit Status register will be
set to a “1”.
TIMER
The LM12(H)454/8 have an on-board 16-bit timer that includes a 5-bit pre-scaler. It uses the clock signal applied
to pin 23 as its input. It can generate time intervals of 0 through 221 clock cycles in steps of 25. This time interval
can be used to delay the execution of instructions. It can also be used to slow the conversion rate when
converting slowly changing signals. This can reduce the amount of redundant data stored in the FIFO and
retrieved by the controller.
The user-defined timing value used by the Timer is stored in the 16-bit READ/WRITE Timer register at location
1011 (A4–A1, BW = 0) or 1011x (A4–A0, BW = 1) and is pre-loaded automatically. Bits 0–7 hold the preset
value's low byte and Bits 8–15 hold the high byte. The Timer is activated by the Sequencer only if the current
instruction's Bit 9 is set (“1”). If the equivalent decimal value “N” (0 N216 1) is written inside the 16-bit Timer
register and the Timer is enabled by setting an instruction's bit 9 to a “1”, the Sequencer will delay the same
instruction's execution by halting at state 3 (S3), as shown in Figure 45, for 32 × N + 2 clock cycles.
DMA
The DMA works in tandem with Interrupt 2. An active DMA Request on pin 32 (DMARQ) requires that the FIFO
interrupt be enabled. The voltage on the DMARQ pin goes high when the number of conversions in the FIFO
equals the 5-bit value stored in the Interrupt Enable register (bits 11–15). The voltage on the INT pin goes low at
the same time as the voltage on the DMARQ pin goes high. The voltage on the DMARQ pin goes low when the
FIFO is emptied. The Interrupt Status register must be read to clear the FIFO interrupt flag in order to enable the
next DMA request.
Copyright © 2004–2006, Texas Instruments Incorporated Submit Documentation Feedback 33
Product Folder Links: LM12454 LM12458 LM12H458
LM12454, LM12458, LM12H458
SNAS079A MAY 2004REVISED FEBRUARY 2006
www.ti.com
DMA operation is optimized through the use of the 16-bit data bus connection (a logic “0” applied to the BW pin).
Using this bus width allows DMA controllers that have single address Read/Write capability to easily unload the
FIFO. Using DMA on an 8-bit data bus is more difficult. Two read operations (low byte, high byte) are needed to
retrieve each conversion result from the FIFO. Therefore, the DMA controller must be able to repeatedly access
two constant addresses when transferring data from the LM12(H)454/8 to the host system.
FIFO
The result of each conversion stored in an internal read-only FIFO (First-In, First-Out) register. It is located at
1100 (A4–A1, BW = 0) or 1100x (A4–A0, BW = 1). This register has 32 16-bit wide locations. Each location holds
13-bit data. Bits 0–3 hold the four LSB's in the 12 bits + sign mode or “1110” in the 8 bits + sign mode. Bits 4–11
hold the eight MSB's and Bit 12 holds the sign bit. Bits 13–15 can hold either the sign bit, extending the register's
two's complement data format to a full sixteen bits or the instruction address that generated the conversion and
the resulting data. These modes are selected according to the logic state of the Configuration register's Bit 5.
The FIFO status should be read in the Interrupt Status register (Bits 11–15) to determine the number of
conversion results that are held in the FIFO before retrieving them. This will help prevent conversion data
corruption that may take place if the number of reads are greater than the number of conversion results
contained in the FIFO. Trying to read the FIFO when it is empty may corrupt new data being written into the
FIFO. Writing more than 32 conversion data into the FIFO by the ADC results in loss of the first conversion data.
Therefore, to prevent data loss, it is recommended that the LM12(H)454/8's interrupt capability be used to inform
the system controller that the FIFO is full.
The lower portion (A0 = 0) of the data word (Bits 0–7) should be read first followed by a read of the upper portion
(A0 = 1) when using the 8-bit bus width (BW = 1). Reading the upper portion first causes the data to shift down,
which results in loss of the lower byte.
Bits 0–12 hold 12-bit + sign conversion data. Bits 0–3 will be 1110 (LSB) when using 8-bit plus sign resolution.
Bits 13–15 hold either the instruction responsible for the associated conversion data or the sign bit. Either mode
is selected with Bit 5 in the Configuration register.
Using the FIFO's full depth is achieved as follows. Set the value of the Interrupt Enable register's Bits 11–15 to
11111 and the Interrupt Enable register's Bit 2 to a “1”. This generates an external interrupt when the 31st
conversion is stored in the FIFO. This gives the host processor a chance to send a “0” to the LM12(H)454/8's
Start bit (Configuration register) and halt the ADC before it completes the 32nd conversion. The Sequencer halts
after the current (32) conversion is completed. The conversion data is then transferred to the FIFO and occupies
the 32nd location. FIFO overflow is avoided if the Sequencer is halted before the start of the 32nd conversion by
placing a “0” in the Start bit (Configuration register). It is important to remember that the Sequencer continues to
operate even if a FIFO interrupt (INT 2) is internally or externally generated. The only mechanisms that stop
the Sequencer are an instruction with the PAUSE bit set to “1” (halts before instruction execution), placing a “0”
in the Configuration register's START bit, or placing a “1” in the Configuration register's RESET bit.
Sequencer
The Sequencer uses a 3-bit counter (Instruction Pointer, or IP, in Figure 40) to retrieve the programmable
conversion instructions stored in the Instruction RAM. The 3-bit counter is reset to 000 during chip reset or if the
current executed instruction has its Loop bit (Bit 1 in any Instruction RAM “00”) set high (“1”). It increments at the
end of the currently executed instruction and points to the next instruction. It will continue to increment up to 111
unless an instruction's Loop bit is set. If this bit is set, the counter resets to “000” and execution begins again with
the first instruction. If all instructions have their Loop bit reset to “0”, the Sequencer will execute all eight
instructions continuously. Therefore, it is important to realize that if less than eight instructions are programmed,
the Loop bit on the last instruction must be set. Leaving this bit reset to “0” allows the Sequencer to execute
“unprogrammed” instructions, the results of which may be unpredictable.
The Sequencer's Instruction Pointer value is readable at any time and is found in the Status register at Bits 8–10.
The Sequencer can go through eight states during instruction execution:
State 0: The current instruction's first 16 bits are read from the Instruction RAM “00”. This state is one clock
cycle long.
State 1: Checks the state of the Calibration and Start bits. This is the “rest” state whenever the Sequencer is
stopped using the reset, a Pause command, or the Start bit is reset low (“0”). When the Start bit is set to a “1”,
this state is one clock cycle long.
34 Submit Documentation Feedback Copyright © 2004–2006, Texas Instruments Incorporated
Product Folder Links: LM12454 LM12458 LM12H458
LM12454, LM12458, LM12H458
www.ti.com
SNAS079A MAY 2004REVISED FEBRUARY 2006
State 2: Perform calibration. If bit 2 or bit 6 of the Configuration register is set to a “1”, state 2 is 76 clock
cycles long. If the Configuration register's bit 3 is set to a “1”, state 2 is 4944 clock cycles long.
State 3: Run the internal 16-bit Timer. The number of clock cycles for this state varies according to the value
stored in the Timer register. The number of clock cycles is found by using the expression below
32T + 2 (3)
where 0 T216 1.
State 7: Run the acquisition delay and read Limit #1's value if needed. The number of clock cycles for 12-bit +
sign mode varies according to
9 + 2D (4)
where D is the user-programmable 4-bit value stored in bits 12–15 of Instruction RAM “00” and is limited to 0 D
15.
The number of clock cycles for 8-bit + sign or “watchdog” mode varies according to
2 + 2D (5)
where D is the user-programmable 4-bit value stored in bits 12–15 of Instruction RAM “00” and is limited to 0 D
15.
State 6: Perform first comparison. This state is 5 clock cycles long.
State 4: Read Limit #2. This state is 1 clock cycle long.
State 5: Perform a conversion or second comparison. This state takes 44 clock cycles when using the 12-bit +
sign mode or 21 clock cycles when using the 8-bit + sign mode. The “watchdog” mode takes 5 clock cycles.
Copyright © 2004–2006, Texas Instruments Incorporated Submit Documentation Feedback 35
Product Folder Links: LM12454 LM12458 LM12H458
LM12454, LM12458, LM12H458
SNAS079A MAY 2004REVISED FEBRUARY 2006
www.ti.com
Figure 45. Sequencer Logic Flow Chart (IP = Instruction Pointer)
36 Submit Documentation Feedback Copyright © 2004–2006, Texas Instruments Incorporated
Product Folder Links: LM12454 LM12458 LM12H458
LM12454, LM12458, LM12H458
www.ti.com
SNAS079A MAY 2004REVISED FEBRUARY 2006
DESIGN CONSIDERATIONS
REFERENCE VOLTAGE
The difference in the voltages applied to the VREF+ and VREFdefines the analog input voltage span (the
difference between the voltages applied between two multiplexer inputs or the voltage applied to one of the
multiplexer inputs and analog ground), over which 4095 positive and 4096 negative codes exist. The voltage
sources driving VREF+ or VREFmust have very low output impedance and noise.
The ADC can be used in either ratiometric or absolute reference applications. In ratiometric systems, the analog
input voltage is proportional to the voltage used for the ADC's reference voltage. When this voltage is the system
power supply, the VREF+ pin is connected to VA+ and VREFis connected to GND. This technique relaxes the
system reference stability requirements because the analog input voltage and the ADC reference voltage move
together. This maintains the same output code for given input conditions.
For absolute accuracy, where the analog input voltage varies between very specific voltage limits, a time and
temperature stable voltage source can be connected to the reference inputs. Typically, the reference voltage's
magnitude will require an initial adjustment to null reference voltage induced full-scale errors.
When using the LM12(H)454/8's internal 2.5V bandgap reference, a parallel combination of a 100 μF capacitor
and a 0.1 μF capacitor connected to the VREFOUT pin is recommended for low noise operation. When left
unconnected, the reference remains stable without a bypass capacitor. However, ensure that stray capacitance
at the VREFOUT pin remains below 50 pF.
INPUT RANGE
The LM12(H)454/8's fully differential ADC and reference voltage inputs generate a two's-complement output that
is found by using the equation below.
(6)
Round up to the next integer value between 4096 to 4095 for 12-bit resolution and between 256 to 255 for 8-
bit resolution if the result of the above equation is not a whole number. As an example, VREF+ = 2.5V, VREF= 1V,
VIN+ = 1.5V and VIN= GND. The 12-bit + sign output code is positive full-scale, or 0,1111,1111,1111. If VREF+ =
5V, VREF= 1V, VIN+ = 3V, and VIN= GND, the 12-bit + sign output code is 0,1100,0000,0000.
INPUT CURRENT
A charging current flows into or out of (depending on the input voltage polarity) the analog input pins, IN0–IN7 at
the start of the analog input acquisition time (tACQ). This current's peak value will depend on the actual input
voltage applied. This charging current causes voltage spikes at the inputs. This voltage spikes will not corrupt the
conversion results.
INPUT SOURCE RESISTANCE
For low impedance voltage sources (<100Ωfor 5 MHz operation and <60Ωfor 8 MHz operation), the input
charging current will decay, before the end of the S/H's acquisition time, to a value that will not introduce any
conversion errors. For higher source impedances, the S/H's acquisition time can be increased. As an example,
operating with a 5 MHz clock frequency and maximum acquisition time, the LM12(H)454/8's analog inputs can
handle source impedance as high as 6.67 kΩ. When operating at 8 MHz and maximum acquisition time, the
LM12H454/8's analog inputs can handle source impedance as high as 4.17 kΩ. Refer to Section 2.1, Instruction
RAM “00”, Bits 12–15 for further information.
INPUT BYPASS CAPACITANCE
External capacitors (0.01 μF to 0.1 μF) can be connected between the analog input pins, IN0–IN7, and analog
ground to filter any noise caused by inductive pickup associated with long input leads. It will not degrade the
conversion accuracy.
Copyright © 2004–2006, Texas Instruments Incorporated Submit Documentation Feedback 37
Product Folder Links: LM12454 LM12458 LM12H458
LM12454, LM12458, LM12H458
SNAS079A MAY 2004REVISED FEBRUARY 2006
www.ti.com
NOISE
The leads to each of the analog multiplexer input pins should be kept as short as possible. This will minimize
input noise and clock frequency coupling that can cause conversion errors. Input filtering can be used to reduce
the effects of the noise sources.
POWER SUPPLIES
Noise spikes on the VA+ and VD+ supply lines can cause conversion errors; the comparator will respond to the
noise. The ADC is especially sensitive to any power supply spikes that occur during the auto-zero or linearity
correction. Low inductance tantalum capacitors of 10 μF or greater paralleled with 0.1 μF monolithic ceramic
capacitors are recommended for supply bypassing. Separate bypass capacitors should be used for the VA+ and
VD+ supplies and placed as close as possible to these pins.
GROUNDING
The LM12(H)454/8's nominal performance can be maximized through proper grounding techniques. These
include the use of a single ground plane and meticulously separating analog and digital areas of the board. The
use of separate analog and digital digital planes within the same board area generally provides best
performance. All components that handle digital signals should be placed within the digital area of the board, as
defined by the digital power plane, while all analog components should be placed in the analog area of the
board. Such placement and the routing of analog and digital signal lines within their own respective board areas
greatly reduces the occurrence of ground loops and noise. This will also minimize EMI/RFI radiation and
susceptibility.
It is recommended that stray capacitance between the analog inputs or outputs, including the reference pins, be
kept to a minimum by increasing the clearance (+1/16th inch) between the analog signal and reference pins and
the ground plane.
CLOCK SIGNAL CONSIDERATIONS
The LM12(H)458's performance is optimized by routing the analog input/output and reference signal conductors
(pins 34–44) as far as possible from the conductor that carries the clock signal to pin 23.
Avoid overshoot and undershoot on the clock line by treating this line as a transmission line (use proper
termination techniques). Failure to do so can result in erratic operation. Generally, a series 30to 50resistor in
the clock line, located as close to the clock source as possible, will prevent most problems. The clock source
should drive ONLY the LM12(H)458 clock pin.
Common Application Problems
Driving the analog inputs with op-amp(s) powered from supplies other than the supply used for the
LM12(H)458. This practice allows for the possibility of the amplifier output (LM12(H)458 input) to reach potentials
outside of the 0V to VA+ range. This could happen in normal operation if the amplifier use supply voltages
outside of the range of the LM12(H)458 supply rails. This could also happen upon power up if the amplifier
supply or supplies ramp up faster than the supply of the LM12(H)458. If any pin experiences a potential more
than 100 mV below ground or above the supply voltage, even on a fast transient basis, the result could be erratic
operation, missing codes, one channel interacting with one or more of the others, skipping channels or a
complete malfunction, depending upon how far the input is driven beyond the supply rails.
Not performing a full calibration at power up. This can result in missing codes. The device needs to have a
full calibration run and completed after power up and BEFORE attempting to perform even a single conversion or
watchdog operation. The only way to recover if this is violated is to interrupt the power to the device.
Not waiting for the calibration process to complete before trying to write to the device. Once a calibration
is requested, the ONLY read of the LM12(H)458 should be if the Interrupt Status Register to check for a
completed calibration. Attempting a write or any other read during calibration would cause a corruption of the
calibration process, resulting in missing codes. The only way to recover would be to interrupt the power.
38 Submit Documentation Feedback Copyright © 2004–2006, Texas Instruments Incorporated
Product Folder Links: LM12454 LM12458 LM12H458
LM12454, LM12458, LM12H458
www.ti.com
SNAS079A MAY 2004REVISED FEBRUARY 2006
Improper termination of digital lines. Improper termination can result in energy reflections that build up to
cause overshoot that goes above the supply potential and undershoot that goes below ground. It is never good
to drive a device beyond the supply rails, unless the device is specifically designed to handle this situation, but
the LM12(H)458 is more sensitive to this condition that most devices. Again, if any pin experiences a potential
more than 100 mV below ground or above the supply voltage, even on a fast transient basis, the result could be
erratic operation, missing codes, or a complete malfunction, depending upon how far the input is driven beyond
the supply rails. The clock input is the most sensitive digital one. Generally, a 50series resistor, located very
close to the signal source, will keep digital lines "clean".
Excessive output capacitance on the digital lines. The current required to charge the capacitance on the
digital outputs can cause noise on the supply bus within the LM12(H)458, causing internal supply "bounce" even
when the external supply pin is pretty stable. The current required to discharge the output capacitance can cause
die ground "bounce". Either of these can cause noise to be induced at the analog inputs, resulting in conversion
errors.
Output capacitance should be limited as much as possible. A series 100resistor in each digital output line,
located very close to the output pin, will limit the charge and discharge current, minimizing the extent of the
conversion errors.
Improper CS decoding. If address decoder is used, care must be exercised to ensure that no "runt" (very
narrow) pulse is produced on theCS line when trying to address another device or memory. Even sub-
nanosecond spikes on the CS line can cause the chip to be reprogrammed in accordance with what happens to
be on the data lines at the time. The result is unexpected operation. The worst case result is that the device is
put into the "Test" mode and the on-board EEPROM that corrects linearity is corrupted. If this happens, the only
recourse is to replace the device.
Copyright © 2004–2006, Texas Instruments Incorporated Submit Documentation Feedback 39
Product Folder Links: LM12454 LM12458 LM12H458
PACKAGE OPTION ADDENDUM
www.ti.com 17-Nov-2018
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM12458CIV/NOPB ACTIVE PLCC FN 44 25 Green (RoHS
& no Sb/Br) CU SN Level-3-245C-168 HR -40 to 85 LM12458CIV
LM12458CIVX/NOPB ACTIVE PLCC FN 44 500 Green (RoHS
& no Sb/Br) CU SN Level-3-245C-168 HR -40 to 85 LM12458CIV
LM12H458CIV/NOPB ACTIVE PLCC FN 44 25 Green (RoHS
& no Sb/Br) CU SN Level-3-245C-168 HR -40 to 85 LM12H458CIV
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
PACKAGE OPTION ADDENDUM
www.ti.com 17-Nov-2018
Addendum-Page 2
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
www.ti.com
PACKAGE OUTLINE
C
44X -.021.013 -0.530.33[ ]
44X -.032.026 -0.810.66[ ]
TYP
-.695.685 -17.6517.40[ ]
40X .050
[1.27]
-.638.582 -16.2014.79[ ]
.020 MIN
[0.51]
TYP-.120.090 -3.042.29[ ]
.180 MAX
[4.57]
B
NOTE 3
-.656.650 -16.6616.51[ ]
A
NOTE 3
-.656.650 -16.6616.51[ ]
(.008)
[0.2]
4215154/A 04/2017
4215154/A 04/2017
PLCC - 4.57 mm max heightFN0044A
PLASTIC CHIP CARRIER
NOTES:
1. All linear dimensions are in inches. Any dimensions in brackets are in millimeters. Any dimensions in parenthesis are for reference only.
Controlling dimensions are in inches. Dimensioning and tolerancing per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. Dimension does not include mold protrusion. Maximum allowable mold protrusion .01 in [0.25 mm] per side.
4. Reference JEDEC registration MS-018.
PIN 1 ID
(OPTIONAL)
144
6
18 28
29
39
40
7
17
.004 [0.1] C
.007 [0.18] C A B
SEATING PLANE
SCALE 0.800
www.ti.com
EXAMPLE BOARD LAYOUT
.002 MAX
[0.05]
ALL AROUND
.002 MIN
[0.05]
ALL AROUND
44X (.093 )
[2.35]
44X (.030 )
[0.75]
40X (.050 )
[1.27]
(.64 )
[16.2]
(.64 )
[16.2]
(R.002 ) TYP
[0.05]
4215154/A 04/2017
4215154/A 04/2017
PLCC - 4.57 mm max heightFN0044A
PLASTIC CHIP CARRIER
NOTES: (continued)
5. Publication IPC-7351 may have alternate designs.
6. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE:4X
SYMM
SYMM
144
6
18 28
29
39
40
7
17
METAL SOLDER MASK
OPENING
NON SOLDER MASK
DEFINED
(PREFERRED) SOLDER MASK DETAILS
EXPOSED METAL
SOLDER MASK
OPENING METAL UNDER
SOLDER MASK
SOLDER MASK
DEFINED
EXPOSED METAL
www.ti.com
EXAMPLE STENCIL DESIGN
44X (.030 )
[0.75]
44X (.093 )
[2.35]
(.64 )
[16.2]
(.64 )
[16.2]
40X (.050 )
[1.27]
(R.002 ) TYP
[0.05]
PLCC - 4.57 mm max heightFN0044A
PLASTIC CHIP CARRIER
4215154/A 04/2017
PLCC - 4.57 mm max heightFN0044A
PLASTIC CHIP CARRIER
NOTES: (continued)
7. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
8. Board assembly site may have different recommendations for stencil design.
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
SCALE:4X
SYMM
SYMM
144
6
18 28
29
39
40
7
17
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2018, Texas Instruments Incorporated