HDSP-A4xC Series
Alphanumeric Display, 0.54" (13.7 mm)
4 Character As AlInGaP Red
Data Sheet
Features
As AlInGaP red color
Gray face paint - Gray package gives optimum con-
trast
Design exibility - Common anode or common
cathode
Applications
Suitable for alphanumeric
Operating temperature range –40C to 105C
Devices
As AlInGaP Red Description
HDSP-A42C Common Anode
HDSP-A47C Common Cathode
Description
These 0.54” (13.7 mm) AS AlInGaP displays are available in
either common anode or common cathode.
Package Dimensions
3.70 (0.140)
7.00 (0.276)
2.37
(0.093)
0.50
(0.020)
5.59
(0.220)
48.6
(1.913)
12.70
(0.500)
12.70
(0.500)
12.70
(0.500)
1.84
(0.072) 50.96
(2.006)
8.17
(0.322)
5°
13.80
(0.543)
21.15
(0.833)
15.24
(0.600)
NOTES:
1. ALL DIMENSIONS ARE IN MILLIMETERS (INCHES).
2. UNLESS OTHERWISE STATED, TOLERANCES ARE ± 0.25 mm.
1.60
(0.063)
PIN 1
1.20
(0.047)
6.00 (0.236)
0.30
(0.012)
2
Part Numbering System
Notes:
1. For codes not listed in the gure above, please refer to the respective datasheet or contact your nearest Avago representative for details.
2. Bin options refer to shippable bins for a part number. Color and Intensity Bins are typically restricted to 1 bin per tube (exceptions may apply).
Please refer to respective datasheet for specic bin limit information.
5082 -X XX X-X X X XX
HDSP-X XX X-X X X XX
Mechanical Options [1]
00: No Mechanical Option
Color Bin Options [1,2]
0: No Color Bin Limitation
Maximum Intensity Bin [1,2]
0: No Maximum Intensity Bin Limitation
Minimum Intensity Bin [1,2]
0: No Minimum Intensity Bin Limitation
Device Conguration/Color [1]
C: AlInGaP Red
Device Specic Conguration [1]
Refer to Respective Datasheet
Package [1]
Refer to Respective Datasheet
3
Internal Circuit
Pin
Pin Conguration A
Common Anode
Pin Conguration B
Common Cathode
1 1E/2E Cathode 1E/2E Anode
2 1M/2M Cathode 1M/2M Anode
3 No Connection No Connection
4 1L/2L Cathode 1L/2L Anode
5 1K/2K Cathode 1K/2K Anode
6 1J/2J Cathode 1J/2J Anode
7 1D/2D Cathode 1D/2D Anode
8 DP2 Cathode DP2 Anode
9 1C/2C Cathode 1C/2C Anode
10 3E/4E Cathode 3E/4E Anode
11 DIGIT No. 3 Common Anode DIGIT No. 3 Common Cathode
12 3D/4D Cathode 3D/4D Anode
13 3J/4J Cathode 3J/4J Anode
14 3M/4M Cathode 3M/4M Anode
15 3L/4L Cathode 3L/4L Anode
16 DIGIT No. 4 Common Anode DIGIT No. 4 Common Cathode
17 3K/4K Cathode 3K/4K Anode
18 3C/4C Cathode 3C/4C Anode
Pin
Pin Conguration A
Common Anode
Pin Conguration B
Common Cathode
1 9 3B/4B Cathode 3B/4B Anode
20 3H/4H Cathode 3H/4H Anode
21 No Connection No Connection
22 3G/4G Cathode 3G/4G Anode
23 3P/4P Cathode 3P/4P Anode
24 3N/4N Cathode 3N/4N Anode
25 3A/4A Cathode 3A/4A Anode
26 DP1 Cathode DP1 Anode
27 3F/4F Cathode 3F/4F Anode
28 1B/2B Cathode 1B/2B Anode
29 DIGIT No. 2 Common Anode DIGIT No. 2 Common Cathode
30 1A/2A Cathode 1A/2A Anode
31 1N/2N Cathode 1N/2N Anode
32 1H/2H Cathode 1H/2H Anode
33 1G/2G Cathode 1G/2G Anode
34 DIGIT No. 1 Common Anode DIGIT No. 1 Common Cathode
35 1P/2P Cathode 1P/2P Anode
36 1F/2F Cathode 1F/2F Anode
DIG 1 DIG 2 DIG 3 DIG 4
DP1
DP2
A
FB
EC
D
G
L
NJ
H
P
MK
COMMON ANODE
COMMON CATHODE
30 28 9 7 1 3633326 5 4231
35 8
30 28 9 7 1 363332 6 5 423135 8
COM 1
DIG 1
3429
ABCDEFGHJKLMN
P
ABCDEFGHJKLMN
PDP2
AB C D EFGHJK LMN P
ABCDEFGHJKLMN
PDP2
ABCDEFGHJKLMNP
ABCDEFGHJKLMN
P
ABCDEFGHJKLMNP
DP1
ABCDEFGHJKLMNP
DP1
COM 2
DIG 2
COM 3
DIG 3
COM 4
DIG 4
11 16 26
11 16 26 25 19 18 12 10 27 22 20 13 17 15 142423
29
COM 2
DIG 2
COM 1
DIG 1
34
COM 3
DIG 3
COM 4
DIG 4
25 19 18 12 10 27 22 20 13 17 15 142423
4
Absolute Maximum Ratings at TA = 25˚C
Description Symbol HDSP-A42C/HDSP-A47C Units
DC Forward Current per Segment or DP [1,2,3] I
F 50 mA
Peak Forward Current per Segment or DP [2,3] I
PEAK 100 mA
Average Forward Current [3] I
AVE 30 mA
Reverse Voltage per Segment or DP (IR = 100 μA) VR 5 V
Operating Temperature TO –40 to +105 ˚C
Storage Temperature TS –40 to +105 ˚C
Wave Soldering Conditions Temperature 250 ˚C
Time 3 s
Notes:
1. Derate linearly as shown in Figure 1.
2. For long term performance with minimal light output degradation, drive currents between 10 mA and 30 mA are recommended. For more in-
formation on recommended drive conditions, please refer to Application Brief I-024 (5966-3087E).
3. Operating at currents below 1 mA is not recommended. Please contact your local representative for further information.
Optical/Electrical Characteristics at TA = 25˚C
Device
Series
HDSP- Parameter Symbol Min. Typ. Max. Units Test Conditions
A42C Forward Voltage IV 1.70 1.90 2.20 V IF = 20 mA
A47C Reverse Voltage VR 5 20 V IF = 100 μA
Peak Wavelength PEAK 635 nm Peak Wavelength
of Spectral Distri-
bution at IF = 20 mA
Dominant Wavelength
[3] d 622.5 626 630 nm
Spectral Halfwidth Δ1/2 17 nm Wavelength Width
at Spectral Distri-
bution 1/2 Power
Point at IF = 20 mA
Speed of Response s 20 ns Exponential Time
Constant, e-ts
Capacitance C 40 pF VF = 0, f = 1 MHz
Intensity Bin Limits [1]
(mcd at 10 mA)
Bin Name Min. [2] Max. [2]
U2536
V3650
W5080
Notes:
1. Bin categories are established for classication of products.
Products may not be available in all bin categories.
2. Tolerance for each bin limit is ± 10%.
Contrast Enhancement
For information on contrast enhancement, please see
Application Note 1015.
Figure 1. Maximum forward current vs. ambient temperature.
Derating based on TJMAX = 130˚C.
Figure 2. Forward current vs. forwrad voltage.
Figure 3. Relative luminous intensity vs. DC forward current.Figure 4. Relative eciency (luminous intensity per unit current)
vs. peak current.
For product information and a complete list of distributors, please go to our web site: www.avagotech.com
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries.
Data subject to change. Copyright © 2005-2010 Avago Technologies. All rights reserved. Obsoletes 5988-9665EN
AV02-1103EN - August 19, 2010
Soldering/Cleaning
Cleaning agents from ketone family (acetone, methyl
ethyl ketone, etc.) and from the chlorinated hydrocarbon
family (methylene chloride, trichloroethylene, carbon
tetrachloride, etc.) are not recommended for cleaning
LED parts. All of these various solvents attack or dissolve
the encapsulating epoxies used to form the package of
plastic LED parts.
For information on soldering LEDs, please refer to Applica-
tion Note 1027.
IF – MAXIMUM AVERAGE CURRENT – mA
0
0
TA – AMBIENT TEMPERATURE – ˚C
60
30
120
40
10
20
20
40
50
60 80 100
IF – FORWARD CURRENT PER SEGMENT – mA
0.0
0
VF – FORWARD VOLTAGE – V
120
60
2.0 3.0
80
20
1.0 2.5
40
1.5
100
RELATIVE LUMINOUS INTENSITY
(NORMALIZED TO 1 AT 10 mA)
0
0
IF – FORWARD CURRENT PER SEGMENT – mA
3.5
3.0
1.5
1.0
40
20 60103050
2.5
2.0
0.5
RELATIVE EFFICIENCY
(NORMALIZED TO 1 AT 10 mA)
001020304060
IPEAK – PEAK FORWARD CURRENT PER SEGMENT – mA
0.2
0.4
0.6
0.8
1.0
1.4
1.2
50
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Avago Technologies:
HDSP-A42C HDSP-A47C