TQP369185 DC-6 GHz Gain Block Applications * * * * * Mobile Infrastructure LTE / WCDMA / CDMA CATV Point to Point General Purpose Wireless SOT-89 Package Product Features * * * * * * * * * Functional Block Diagram DC-6000 MHz Robust Class 2 (>2000V) HBM ESD Rating 19 dB Gain at 1.9 GHz 4.7 dB Noise Figure at 1.9 GHz +31.7 dBm Output IP3 at 1.9 GHz +19.6 dBm P1dB at 1.9 GHz 50 Ohm Cascadable Gain Block Internal active bias SOT-89 Package GND 4 General Description 1 2 3 RF IN GND RF OUT Pin Configuration The TQP369185 is a general-purpose buffer amplifier that offers high dynamic range in a low-cost surfacemount package. At 1.9 GHz, the amplifier typically provides 19 dB gain, +31.7 dBm OIP3, and 4.6 dB Noise Figure while drawing 75 mA current. The device combines dependable performance with consistent quality to maintain MTTF values exceeding 100 years at mounting temperatures of +85C. The device is housed in a lead-free/green/RoHS-compliant industry-standard SOT-89 package. The TQP369185 consists of a Darlington-pair amplifier using TriQuint's high reliability InGaP/GaAs HBT process technology. Internal active bias enables operation with only DC-blocking capacitors and an RF choke on the DC bias feed. This broadband MMIC amplifier can be directly applied to various current and next generation wireless technologies such as CDMA, W-CDMA, and LTE. In addition, the TQP369185 will work for other various applications within the DC to 6 GHz frequency range. Pin No. 1 3 2,4 Label RF IN RF OUT GND Ordering Information Part No. TQP369185 TQP369185-PCB Description InGaP/GaAs HBT Gain Block 0.5-4 GHz Evaluation Board Standard T/R size = 2500 pieces on a 13" reel Datasheet: Rev E 7/16/13 (c) 2013 TriQuint - 1 of 8 - Disclaimer: Subject to change without notice www.triquint.com TQP369185 DC-6 GHz Gain Block Absolute Maximum Ratings Recommended Operating Conditions Parameter Parameter Storage Temperature RF Input Power, CW, 50, T=25C Device Voltage (VCC) Rating -55 to 150C +25 dBm +7.0 V Operation of this device outside the parameter ranges given above may cause permanent damage. Min VCC +4.75 TCASE -40 6 Tj (for >10 hours MTTF) Typ +5 Max Units +5.25 +85 +170 V C C Electrical specifications are measured at specified test conditions. Specifications are not guaranteed over all recommended operating conditions. Electrical Specifications Test conditions unless otherwise noted: VCC =5 V, TCASE= +25C, 50 system Parameter Operational Frequency Range Test Frequency Gain Input Return Loss Output Return Loss Output P1dB Output IP3 Noise Figure Device Voltage (VCC) Device Current (ICC) Thermal Resistance (jc) Conditions Min DC 17.5 Pout=0 dBm/tone, f= 1 MHz +28 55 Junction to base(1) Typ 1900 19 -13.5 -9.6 +19.6 +31.7 4.6 5 75 Max 6000 20.5 92 82 Units MHz MHz dB dB dB dBm dBm dB V mA o C/W Notes: 1. Thermal path is from device junction through package ground tab (pins 2,4) to mounting surface. Datasheet: Rev E 7/16/13 (c) 2013 TriQuint - 2 of 8 - Disclaimer: Subject to change without notice www.triquint.com TQP369185 DC-6 GHz Gain Block S-Parameters Test Conditions: VCC=+5.0 V (typ.), ICC=72 mA (typ.), TCASE=+25C, unmatched 50 system, calibrated to device leads Freq (MHz) S11 (dB) S11 (ang) S21 (dB) S21 (ang) S12 (dB) S12 (ang) S22 (dB) S22 (ang) 10 -19.3 -178.5 21.3 179.4 -26.2 0.5 -14.3 3.2 20 -19.0 -177.3 21.4 178.6 -26.1 0.5 -14.0 1.0 50 -18.6 -175.6 21.4 177.6 -26.0 -0.4 -14.3 -2.7 100 -18.4 -176.9 21.3 174.5 -26.1 -0.3 -14.4 -8.5 200 -17.9 -170.6 21.3 169.7 -26.1 -0.6 -14.0 -16.2 500 -16.9 -169.8 21.0 155.4 -26.0 -2.7 -13.4 -43.7 1000 -14.3 -173.6 20.5 132.9 -25.6 -6.1 -12.0 -83.8 1500 -12.3 178.7 20.0 110.6 -25.1 -10.7 -10.4 -119.2 2000 -10.7 163.5 19.3 89.1 -24.5 -18.4 -8.9 -149.9 2500 -9.1 148.7 18.5 68.1 -24.2 -26.3 -7.9 -177.8 3000 -7.8 136.2 17.7 49.2 -23.8 -34.8 -7.0 160.8 3500 -6.9 125.7 16.8 30.8 -23.5 -44.4 -6.3 141.0 4000 -6.5 115.7 15.8 12.5 -23.5 -53.7 -5.3 122.0 4500 -6.7 101.4 14.7 -4.6 -23.7 -62.5 -5.0 104.1 5000 -5.8 89.6 13.7 -19.6 -23.5 -69.4 -4.7 90.3 5500 -4.8 80.2 13.1 -36.1 -23.5 -79.2 -4.1 78.6 6000 -4.3 69.8 12.1 -52.3 -23.7 -89.4 -4.0 66.0 Datasheet: Rev E 7/16/13 (c) 2013 TriQuint - 3 of 8 - Disclaimer: Subject to change without notice www.triquint.com TQP369185 DC-6 GHz Gain Block TQP369185-PCB Evaluation Board J3 Vcc J3 J4 J4 GND R1 C1 J1 C2 L1 C1 Q1 C3 0.018 uF L1 39 nH C3 J2 J1 RF Input C2 1 56 pF J2 3 Q1 2,4 56 pF RF Output Notes: 1. See Evaluation Board PCB Information section for material and stack-up. 2. All components are of 0603 size unless otherwise stated. 3. Zero Ohm resistor R1 is used to bridge a trace gap on PCB 1075825 and is not required in end user applications. Bill of Material - TQP369185-PCB Reference Des. Q1 C1 C2, C3 L1 R1 Value n/a 0.018 uF 56 pF 39 nH 0 Description High Linearity LNA Gain Block Cap, Chip, 0603, 16V, X7R, 10% Cap, Chip, 0603, 50V, NPO, 5% Inductor, 0603, 5%, CS Series Res, Chip, 603, 1/10W, 5% Manuf. TriQuint various various Coilcraft various Part Number TQP369185 Component Values for Specific Frequencies Use the component values in this table for optimal operation at specific frequencies. Reference Designator L1 C2, C3 Datasheet: Rev E 7/16/13 (c) 2013 TriQuint 50 820 nH .018 uF 500 220 nH 1000 pF Frequency (MHz) 900 1900 2200 68 nH 100 pF - 4 of 8 - 27 nH 68 pF 22 nH 68 pF 2500 18 nH 56 pF 3500 15 nH 39 pF Disclaimer: Subject to change without notice www.triquint.com TQP369185 DC-6 GHz Gain Block Typical Performance - TQP369185-PCB Test conditions unless otherwise noted: VSUPPLY =+5 V, ICC = 75 mA, TCASE = +25C Parameter Frequency Gain Input Return Loss Output Return Loss Output P1dB OIP3 Noise Figure 500 20.5 11.7 17.8 20.9 +33.3 4.5 900 20.4 12.4 15.9 +19.8 +32.3 4.7 Typical Value 1900 19.0 12.3 10 +19.6 +31.7 4.6 2100 18.6 13.3 9.3 +19.5 +31.7 4.7 2600 18.0 13.7 8.7 +19 +30.6 4.8 3500 16.8 -6.9 -6.3 +17.5 +28.6 4.9 4000 15.8 -6.5 -5.3 +15.8 +27.1 5.1 5000 13.7 -5.8 -4.7 +13.9 +24.4 5.6 Units 6000 12.1 -4.3 -4 +12.3 +23.4 6.3 MHz dB dB dB dBm dBm dB Notes: 1. OIP3 measured with two tones at an output power of 0 dBm / tone separated by 1 MHz. Performance Plots - TQP369185-PCB Test conditions unless otherwise noted: VSUPPLY =+5 V, ICC = 75 mA, TCASE = +25C Gain vs. Frequency 22 Input Return Loss vs. Frequency 0 Output Return Loss vs. Frequency 0 14 |S22| (dB) 16 -5 -5 +85C +25C 40C 18 |S11| (dB) |S21| (dB) 20 -10 +85C -15 40C 40C 10 -20 0 1 2 3 5 4 -20 0 6 1 2 Frequency (GHz) 3 4 5 6 0 Freq. =900 MHz 1 MHz Tone Spacing OIP3 (dBm) 31 30 3 4 5 6 Freq. =1900 MHz 1 MHz Tone Spacing 33 32 2 OIP3 vs. Output Power/Tone 34 +85C +25C -40C 33 1 Frequency (GHz) Frequency (GHz) OIP3 vs. Output Power/Tone 34 OIP3 (dBm) +25C -15 +25C 12 +85C -10 +85C +25C -40C 32 31 30 29 29 -3 -2 -1 0 1 2 3 4 Output Power/Tone (dBm) Datasheet: Rev E 7/16/13 (c) 2013 TriQuint 5 6 7 -3 -2 -1 0 1 2 3 4 5 6 7 Output Power/Tone (dBm) - 5 of 8 - Disclaimer: Subject to change without notice www.triquint.com TQP369185 DC-6 GHz Gain Block Pin Configuration and Description GND 4 Pin No. Label 3 RF OUT 2, 4, Backside Paddle GND Paddle 1 1 2 3 RF IN GND RF OUT RF IN Description RF input, matched to 50 ohms. External DC Block is required. RF output / DC supply, matched to 50 ohms. External DC Block and bias choke, are required. RF/DC ground. Use recommended via pattern to minimize inductance and thermal resistance. See PCB Mounting Pattern for suggested footprint. Evaluation Board PCB Information TriQuint PCB 1075825 Material and Stack-up 50 Ohm Line Dimensions: width=0.028" spacing=0.028" Datasheet: Rev E 7/16/13 (c) 2013 TriQuint - 6 of 8 - Disclaimer: Subject to change without notice www.triquint.com TQP369185 DC-6 GHz Gain Block Package Marking and Dimensions Marking: Part number - 369185 Lot code - AaXXXX -YD D1 D1 D1 4 369185 AaXXXX 1 2 3 E1 E -Z- M H L 2X B1 B e e1 C 3 PLACES 0.10 (0.004) M T Alternate Backside Patterns - Reflow Compatible (Part may be supplied with either pattern) -TZ S Y S SYMBOL A 7 B B1 A C D D1 MIN 1.40 (.055) .44 (.017) .36 (.014) .35 (.014) 4.40 (.173) 1.62 (.064) TYP 1.50 (.059) .50 (.020) .42 (.0165) .40 (.016) 4.50 (.177) 1.73 (.068) MAX 1.60 (.063) .56 (.022) .48 (.019) .44 (.017) 4.60 (.181) 1.83 (.072) SYMBOL E E1 MIN 2.29 (.090) 2.13 (.084) e e1 H L M 3.94 (.155) .89 (.035) 2.2 (.087) TYP 2.50 (.098) 2.20 (.087) 1.50 BSC (.059) 3.00 BSC (.118) 4.10 (.161) 1.10 (.043) 2.40 (.095) MAX 2.60 (.102) 2.29 (.090) 4.25 (.167) 1.20 (.047) 2.6 (.102) Notes: 1. All dimensions are in millimeters. Angles are in degrees. 2. Dimension and tolerance formats conform to ASME Y14.4M-1994. 3. The terminal #1 identifier and terminal numbering conform to JESD 95-1 SPP-012. 4. Contact plating: NiPdAu PCB Mounting Pattern 3.86 [0.152] 29X 3 1.26 [0.050] 0.63 [0.025] 0.76 [0.030] 4.50 [0.177] O.254 (.010) PLATED THRU VIA HOLES PACKAGE OUTLINE 2X 1.27 [0.050] 2X 0.58 [0.023] 2.65 [0.104] 2X 0.86 [0.034] 0.64 [0.025] 0.86 [0.034] 3.86 [0.152] Notes: 1. All dimensions are in millimeters. Angles are in degrees. 2. Use 1 oz. copper minimum for top and bottom layer metal. 3. Vias are required under the backside paddle of this device for proper RF/DC grounding and thermal dissipation. 4. Do not remove or minimize via hole structure in the PCB. Thermal and RF grounding is critical. 5. We recommend a 0.35mm (#80/.0135") diameter bit for drilling via holes and a final plated thru diameter of 0.25 mm (0.10"). 6. Ensure good package backside paddle solder attach for reliable operation and best electrical performance. Datasheet: Rev E 7/16/13 (c) 2013 TriQuint - 7 of 8 - Disclaimer: Subject to change without notice www.triquint.com TQP369185 DC-6 GHz Gain Block Product Compliance Information ESD Sensitivity Ratings Solderability Compatible with both lead-free (260C maximum reflow temperature) and tin/lead (245C maximum reflow temperature) soldering processes. Caution! ESD-Sensitive Device Contact plating: NiPdAu ESD Rating: Value: Test: Standard: Class 2 2000 V to < 4000 V Human Body Model (HBM) JEDEC Standard JESD22-A114 ESD Rating: Value: Test: Standard: Class IV Passes 1000 V Charged Device Model (CDM) JEDEC Standard JESD22-C101 RoHs Compliance This part is compliant with EU 2002/95/EC RoHS directive (Restrictions on the Use of Certain Hazardous Substances in Electrical and Electronic Equipment). This product also has the following attributes: * Lead Free * Halogen Free (Chlorine, Bromine) * Antimony Free * TBBP-A (C15H12Br402) Free * PFOS Free * SVHC Free MSL Rating MSL Rating: Level 1 Test: 260C convection reflow Standard: JEDEC Standard IPC/JEDEC J-STD-020 Contact Information For the latest specifications, additional product information, worldwide sales and distribution locations, and information about TriQuint: Web: www.triquint.com Email: info-sales@triquint.com Tel: Fax: +1.503.615.9000 +1.503.615.8902 For technical questions and application information: Email: sjcapplications.engineering@triquint.com Important Notice The information contained herein is believed to be reliable. TriQuint makes no warranties regarding the information contained herein. TriQuint assumes no responsibility or liability whatsoever for any of the information contained herein. TriQuint assumes no responsibility or liability whatsoever for the use of the information contained herein. The information contained herein is provided "AS IS, WHERE IS" and with all faults, and the entire risk associated with such information is entirely with the user. All information contained herein is subject to change without notice. Customers should obtain and verify the latest relevant information before placing orders for TriQuint products. The information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or anything described by such information. TriQuint products are not warranted or authorized for use as critical components in medical, life-saving, or lifesustaining applications, or other applications where a failure would reasonably be expected to cause severe personal injury or death. Datasheet: Rev E 7/16/13 (c) 2013 TriQuint - 8 of 8 - Disclaimer: Subject to change without notice www.triquint.com