1025934 - TriQuint Semiconductor

TQP369185

DC-6 GHz Gain Block

Datasheet: Rev E 7/16/13

- 1 of 8 -

Disclaimer: Subject to change without notice

www.triquint.com

Applications

• Mobile Infrastructure

• LTE / WCDMA / CDMA

• CATV

• Point to Point

• General Purpose Wireless

SOT-89 Package

Product Features

• DC-6000 MHz

• Robust Class 2 (>2000V) HBM ESD Rating

• 19 dB Gain at 1.9 GHz

• 4.7 dB Noise Figure at 1.9 GHz

• +31.7 dBm Output IP3 at 1.9 GHz

• +19.6 dBm P1dB at 1.9 GHz

• 50 Ohm Cascadable Gain Block

• Internal active bias

• SOT-89 Package

Functional Block Diagram

RF IN GND RF OUT

GND

Pin Configuration

Pin No.

Label

RF IN

RF OUT

2,4

GND

General Description

The TQP369185 is a general-purpose buffer amplifier

that offers high dynamic range in a low

-cost surface-

mount package. At 1.9 GHz, the amplifier typically

provides

19 dB gain, +31.7 dBm OIP3, and 4.6 dB

Noise Figure while drawing

mA current. The device

combines dependable performance with consistent

quality to maintain MTTF values exceeding 100 years at

mounting temperatures of +85°C. The device is housed

in a lead

-free/green/RoHS-compliant industry-standard

SOT

-89 package.

The TQP36

9185 consists of a Darlington-

pair amplifier

using TriQuint’s high reliability InGaP/GaAs HBT

process technology. Internal active bias enables

ope

ration with only DC-blocking capacitors

and an RF

choke

on the DC bias feed. This

broadband MMIC

amplifier can be directly applied to various current and

next generation wireless technologies such as CDMA,

-CDMA, and LTE. In addition, the TQP369185 will

work for other various applications within the DC to 6

GHz frequency range.

Ordering Information

Part No.

Description

TQP369185

InGaP/GaAs HBT Gain Block

TQP369185-PCB

0.5-4 GHz Evaluation Board

Standard T/R size = 2500 pieces on a 13” reel

TQP369185

DC-6 GHz Gain Block

Datasheet: Rev E 7/16/13

- 2 of 8 -

Disclaimer: Subject to change without notice

www.triquint.com

Recommended Operating Conditions

Parameter

Min

Typ

Max

Units

VCC

+4.75

+5.25

TCASE

−40

+85

°C

Tj (for >106 hours MTTF)

+170

°C

Electrical specifications are measured at specified test

conditions. Specifications are not guaranteed over all

recommended operating conditions.

Absolute Maximum Ratings

Parameter

Rating

Storage Temperature

−55 to 150°C

RF Input Power, CW, 50Ω, T=25°C

+25 dBm

Device Voltage (VCC)

+7.0 V

Operation of this device outside the parameter ranges

given above may cause permanent damage.

Electrical Specifications

Test conditions unless otherwise noted: V

=5 V, TCASE= +25°C, 50Ω system

Parameter

Conditions

Min

Typ

Max

Units

Operational Frequency Range

6000

MHz

Test Frequency

1900

MHz

Gain

17.5

20.5

Input Return Loss

-13.5

Output Return Loss

-9.6

Output P1dB

+19.6

dBm

Output IP3

Pout=0 dBm/tone, Δf= 1 MHz

+28

+31.7

dBm

Noise Figure

4.6

Device Voltage (VCC)

Device Current (ICC)

Thermal Resistance (θjc)

Junction to base(1)

oC/W

Notes:

1. Thermal path is from device junction through package ground tab (pins 2,4) to mounting surface.

TQP369185

DC-6 GHz Gain Block

Datasheet: Rev E 7/16/13

- 3 of 8 -

Disclaimer: Subject to change without notice

www.triquint.com

S-Parameters

Test Conditions: VCC=+5.0 V (typ.), ICC=72 mA (typ.), TCASE=+25°C, unmatched 50Ω system, calibrated to device leads

Freq (MHz)

S11 (dB)

S11 (ang)

S21 (dB)

S21 (ang)

S12 (dB)

S12 (ang)

S22 (dB)

S22 (ang)

10 -19.3 -178.5 21.3 179.4 -26.2 0.5 -14.3 3.2

20 -19.0 -177.3 21.4 178.6 -26.1 0.5 -14.0 1.0

50 -18.6 -175.6 21.4 177.6 -26.0 -0.4 -14.3 -2.7

100 -18.4 -176.9 21.3 174.5 -26.1 -0.3 -14.4 -8.5

200 -17.9 -170.6 21.3 169.7 -26.1 -0.6 -14.0 -16.2

500 -16.9 -169.8 21.0 155.4 -26.0 -2.7 -13.4 -43.7

1000 -14.3 -173.6 20.5 132.9 -25.6 -6.1 -12.0 -83.8

1500 -12.3 178.7 20.0 110.6 -25.1 -10.7 -10.4 -119.2

2000 -10.7 163.5 19.3 89.1 -24.5 -18.4 -8.9 -149.9

2500 -9.1 148.7 18.5 68.1 -24.2 -26.3 -7.9 -177.8

3000 -7.8 136.2 17.7 49.2 -23.8 -34.8 -7.0 160.8

3500 -6.9 125.7 16.8 30.8 -23.5 -44.4 -6.3 141.0

4000 -6.5 115.7 15.8 12.5 -23.5 -53.7 -5.3 122.0

4500 -6.7 101.4 14.7 -4.6 -23.7 -62.5 -5.0 104.1

5000 -5.8 89.6 13.7 -19.6 -23.5 -69.4 -4.7 90.3

5500 -4.8 80.2 13.1 -36.1 -23.5 -79.2 -4.1 78.6

6000 -4.3 69.8 12.1 -52.3 -23.7 -89.4 -4.0 66.0

TQP369185

DC-6 GHz Gain Block

Datasheet: Rev E 7/16/13

- 4 of 8 -

Disclaimer: Subject to change without notice

www.triquint.com

TQP369185-PCB Evaluation Board

J4 J3

J1 J2

Output

J4 GND

J3 Vcc

2,4

Input

39 nH

56 pF

0.018 uF

Notes:

1. See Evaluation Board PCB Information section for material and stack-up.

2. All components are of 0603 size unless otherwise stated.

3. Zero Ohm resistor R1 is used to bridge a trace gap on PCB 1075825 and is not required in end user applications.

Bill of Material − TQP369185-PCB

Reference Des.

Value

Description

Manuf.

Part Number

Q1 n/a High Linearity LNA Gain Block TriQuint TQP369185

0.018 uF

Cap, Chip, 0603, 16V, X7R, 10%

various

C2, C3

56 pF

Cap, Chip, 0603, 50V, NPO, 5%

various

39 nH

Inductor, 0603, 5%, CS Series

Coilcraft

0 Ω

Res, Chip, 603, 1/10W, 5%

various

Component Values for Specific Frequencies

Use the component values in this table for optimal operation at specific frequencies

Reference

Designator

Frequency (MHz)

500

900

1900

2200

2500

3500

820 nH

220 nH

68 nH

27 nH

22 nH

18 nH

15 nH

C2, C3

.018 uF

1000 pF

100 pF

68 pF

56 pF

39 pF

TQP369185

DC-6 GHz Gain Block

Datasheet: Rev E 7/16/13

- 5 of 8 -

Disclaimer: Subject to change without notice

www.triquint.com

Typical Performance − TQP369185-PCB

Test conditions unless otherwise noted: VSUPPLY =+5 V, ICC = 75 mA, TCASE = +25

Parameter

Typical Value

Units

Frequency

500

900

1900

2100

2600

3500

4000

5000

6000

MHz

Gain

20.5

20.4

19.0

18.6

18.0

16.8

15.8

13.7

12.1

Input Return Loss

11.7

12.4

12.3

13.3

13.7

-6.9

-6.5

-5.8

-4.3

Output Return Loss

17.8

15.9

9.3

8.7

-6.3

-5.3

-4.7

-4

Output P1dB

20.9

+19.8

+19.6

+19.5

+19

+17.5

+15.8

+13.9

+12.3

dBm

OIP3

+33.3

+32.3

+31.7

+30.6

+28.6

+27.1

+24.4

+23.4

dBm

Noise Figure 4.5 4.7 4.6 4.7 4.8 4.9 5.1 5.6 6.3 dB

Notes:

1. OIP3 measured with two tones at an output power of 0 dBm / tone separated by 1 MHz.

Performance Plots − TQP369185-PCB

Test conditions unless otherwise noted: VSUPPLY =+5 V, ICC = 75 mA, TCASE = +25

0123456

|S21| (dB)

Frequency (GHz)

Gain vs. Frequency

+85°C

+25°C

40°C

-20

-15

-10

-5

0123456

|S11| (dB)

Frequency (GHz)

Input Return Loss vs. Frequency

+85°C

+25°C

40°C

-20

-15

-10

-5

0 1 2 3 4 5 6

|S22| (dB)

Frequency (GHz)

Output Return Loss vs. Frequency

+85°C

+25°C

40°C

-3 -2 -1 0 1 2 3 4 5 6 7

OIP3 (dBm)

Output Power/Tone (dBm)

OIP3 vs. Output Power/Tone

+85

+25

−40

Freq. =900 MHz

1 MHz Tone Spacing

-3 -2 -1 0 1 2 3 4 5 6 7

OIP3 (dBm)

Output Power/Tone (dBm)

OIP3 vs. Output Power/Tone

+85°C

+25°C

−40°C

Freq. =1900 MHz

1 MHz Tone Spacing

TQP369185

DC-6 GHz Gain Block

Datasheet: Rev E 7/16/13

- 6 of 8 -

Disclaimer: Subject to change without notice

www.triquint.com

Pin Configuration and Description

RF IN GND RF OUT

GND

Pin No.

Label

Description

RF IN

RF input, matched to 50 ohms. External DC Block is required.

3 RF OUT

RF output / DC supply, matched to 50 ohms. External DC Block

and bias choke, are required.

2, 4, Backside Paddle GND Paddle

RF/DC ground. Use recommended via pattern to minimize

inductance and thermal resistance. See PCB Mounting Pattern

for suggested footprint.

Evaluation Board PCB Information

TriQuint PCB 1075825 Material and Stack-up

50 Ohm Line Dimensions: width=0.028"

spacing=0.028"

TQP369185

DC-6 GHz Gain Block

Datasheet: Rev E 7/16/13

- 7 of 8 -

Disclaimer: Subject to change without notice

www.triquint.com

Package Marking and Dimensions

Marking: Part number – 369185

Lot code – AaXXXX

0.10 (0.004)

3 PLACES

MTSZ Y S

123

-Z-

1.62

(.064)

4.40

(.173)

.35

(.014)

.36

(.014)

.44

(.017)

1.40

(.055)

SYMBOL

4.60

(.181)

4.50

(.177)

1.83

(.072)

1.73

(.068)

1.60

(.063)

MAX

.44

(.017)

.48

(.019)

.56

(.022)

.50

(.020)

.40

(.016)

.42

(.0165)

1.50

(.059)

TYPMIN

2.2

(.087)

3.94

(.155)

2.13

(.084)

2.29

(.090)

SYMBOL

2.6

(.102)

2.40

(.095)

2.29

(.090)

2.60

(.102)

4.25

(.167)

1.20

(.047)

1.50 BSC

(.059)

1.10

(.043)

4.10

(.161)

3.00 BSC

(.118)

2.20

(.087)

2.50

(.098)

MAXMIN

.89

(.035)

TYP

7°

2X B1

-Y-

-T-

E1 M

D1 D1

Alternate Backside Patterns - Reflow Compatible

(Part may be supplied with either pattern)

Notes:

1. All dimensions are in millimeters. Angles are in degrees.

2. Dimension and tolerance formats conform to ASME Y14.4M-1994.

3. The terminal #1 identifier and terminal numbering conform to JESD 95-1 SPP-012.

4. Contact plating: NiPdAu

PCB Mounting Pattern

3.86 [0.152]

0.64 [0.025] 2X 0.86 [0.034]

0.76 [0.030]

0.63 [0.025]

Ø.254 (.010) PLATED THRU VIA HOLES

1.26 [0.050]

2X 1.27 [0.050]

0.86 [0.034]

2X 0.58 [0.023]

4.50 [0.177]

2.65 [0.104]

PACKAGE OUTLINE

3.86 [0.152]

29X

Notes:

1. All dimensions are in millimeters. Angles are in degrees.

2. Use 1 oz. copper minimum for top and bottom layer metal.

3. Vias are required under the backside paddle of this device for proper RF/DC grounding and thermal dissipation.

4. Do not remove or minimize via hole structure in the PCB. Thermal and RF grounding is critical.

5. We recommend a 0.35mm (#80/.0135") diameter bit for drilling via holes and a final plated thru diameter of 0.25 mm (0.10”).

6. Ensure good package backside paddle solder attach for reliable operation and best electrical performance.

369185

AaXXXX

TQP369185

DC-6 GHz Gain Block

Datasheet: Rev E 7/16/13

- 8 of 8 -

Disclaimer: Subject to change without notice

www.triquint.com

Product Compliance Information

ESD Sensitivity Ratings

Caution! ESD-Sensitive Device

ESD Rating:

Class 2

Value:

≥ 2000 V to < 4000 V

Test:

Human Body Model (HBM)

Standard:

JEDEC Standard JESD22-A114

ESD Rating:

Class IV

Value:

Passes ≥ 1000 V

Test:

Charged Device Model (CDM)

Standard:

JEDEC Standard JESD22-C101

Solderability

Compatible with both lead

free (260°C maximum reflow

temperature) and tin/lead (245°C maximum reflow

temperature) soldering processes.

Contact plating:

NiPdAu

RoHs Compliance

This part

compliant with EU 2002/95/EC RoHS

directive (Restrictions on the Use of Certain Hazardous

Substances in Electrical and Electronic Equipment).

This product also has the following attributes:

• Lead Free

• Halogen Free (Chlorine, Bromine)

• Antimony Free

• TBBP-A (C15H12Br402) Free

• PFOS Free

• SVHC Free

MSL Rating

MSL Rating:

Level 1

Test:

260°C convection reflow

Standard:

JEDEC Standard IPC/JEDEC J-STD-020

Contact Information

For the latest specifications, additional product information, worldwide sales and distribution locations, and information

about TriQuint:

Web: www.triquint.com Tel: +1.503.615.9000

Email: info-sales@triquint.com Fax: +1.503.615.8902

For

technical questions and application information:

Email: sjcapplications.engineering@triquint.com

Important Notice

The information contained herein is believed to be reliable. TriQuint makes no warranties regarding the information

contained herein. TriQuint assumes no responsibility or liability whatsoever for any of the information contained

herein. TriQuint assumes no responsibility or liability whatsoever for the use of the informa

tion contained herein.

The

information contained herein is provided "AS IS, WHERE IS" and with all faults, and the entire risk associated with

such information is entirely with the user.

All information contained herein is subject to change without notic

Customers should obtain and verify the latest relevant information before placing orders for TriQuint products. The

information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any

patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or

anything described by such information.

TriQuint products are not warranted or authorized for use as critical components in medical, life

-saving, or life

sustaining applications, or other applications where a failure would reasonably be expected to cause severe personal

injury or death.