96 MHz SAW Filter
5 MHz bandwidth
Part Number SF0096BA02438S
IDT SAW Products 324 Clark Street, Worcester, MA 01606, USA Ph 1-508-852-5400 Fax 1-508-852-8456
www.idt.com DSSF0096BA02438S Rev A 23-Aug-2006
Page 1 of 3
DESCRIPTION
96 MHz SAW bandpass filter with 5 MHz bandwidth.
13.3 x 6.5 mm SMP.
RoHS compliant.
TYPICAL PERFORMANCE
Horizontal: Frequency : 4 MHz/div
Vertical from Top: Relative Magnitude : 10 dB/div
Relative magnitude : 0.8 dB/div
Phase Linearity : 10 deg/div
Group Delay Deviation : 100 ns/div
S11 S22
96 MHz SAW Filter
5 MHz bandwidth
Part Number SF0096BA02438S
IDT SAW Products 324 Clark Street, Worcester, MA 01606, USA Ph 1-508-852-5400 Fax 1-508-852-8456
www.idt.com DSSF0096BA02438S Rev A 23-Aug-2006
Page 2 of 3
SPECIFICATION
Parameter 1 Min Typ Max Units
Center Frequency (Fc) 3 95.9 96.0 96.1 MHz
Minimum Insertion Loss - 13.5 15 dB
1 dB Bandwidth 5.00 5.38 - MHz
15 dB Bandwidth - 7.48 8.00 MHz
Passband Variation (Fc +/- 1.92 MHz) - 0.5 0.8 dB p-p
Phase Linearity (Fc +/- 1.92 MHz) - 2.4 5.0 deg p-p
Group Delay Variation (Fc +/- 1.92 MHz) 2 - 35 80 ns p-p
Absolute Delay - 1.23 3 us
Change in Absolute Delay (from unit to unit) -10 0 10 ns
Absolute Delay Variation (from -40˚C to 55˚C) - 5 15 ns
Input Return Loss (Fc+/-1.92 MHz) 10 13 - dB
Output Return Loss (Fc+/-1.92 MHz) 10 13 - dB
Rejection (40 to 87 MHz) 43 48 - dB
Rejection (105 to 150 MHz) 43 48 - dB
Source and Load Impedance - 50 -
Ambient Temperature - 25 -
°C
Notes:
1. All dB levels are referenced to the insertion loss
2. A smoothing aperture of 0.125 MHz may be applied to this measurement.
3. Average of lower and upper 3 dB frequencies; applies at 23°C only.
MAXIMUM RATINGS
Parameter Min Max Units
Storage Temperature Range -40 85 ˚C
Operating Temperature Range -40 55 ˚C
Input Power Level - 13 dBm
MATCHING CIRCUIT
Typical component values: Ls1 = 91 nH Ls2 = 150 nH
(Minimum inductor Q = 40) Lp1 = 39 nH Lp2 = 47 nH
Rp1 = 4.7 K Rp2 = 1.8 K
Notes
Suggest the use of 2% tolerance matching components.
Tuning values shown are for reference only. Optimum values may change depending upon board layout.
Input
50
Single ended
Output
50
Single ended
96 MHz SAW Filter
5 MHz bandwidth
Part Number SF0096BA02438S
IDT SAW Products 324 Clark Street, Worcester, MA 01606, USA Ph 1-508-852-5400 Fax 1-508-852-8456
www.idt.com DSSF0096BA02438S Rev A 23-Aug-2006
Page 3 of 3
PACKAGE OUTLINE SUGGESTED FOOTPRINT
ISO 9001
Registered
Units: mm
Tolerances are ±0.15 mm except
for the overall length and width,
which are nominal values.
Pad Configuration:
Input: 1
Output: 6
Ground: All other pads
Package Material:
Body: Al2O3 ceramic
Lid: Kovar, Ni plated
Terminations: Au plating 1 µm min,
over a 1.3-8.9 µm Ni plating
All specifications are believed to be accurate and reliable. However, MNC reserves the right to make changes without notice.
© 2006 All rights reserved.