HA-5002 (R) Data Sheet March 8, 2006 FN2921.11 110MHz, High Slew Rate, High Output Current Buffer Features The HA-5002 is a monolithic, wideband, high slew rate, high output current, buffer amplifier. * High Input Impedance . . . . . . . . . . . . . . . . . . . . . .3000k Utilizing the advantages of the Intersil D.I. technologies, the HA-5002 current buffer offers 1300V/s slew rate with 110MHz of bandwidth. The 200mA output current capability is enhanced by a 3 output impedance. * Very Wide Bandwidth . . . . . . . . . . . . . . . . . . . . . . 110MHz * Voltage Gain. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.995 The monolithic HA-5002 will replace the hybrid LH0002 with corresponding performance increases. These characteristics range from the 3000k input impedance to the increased output voltage swing. Monolithic design technologies have allowed a more precise buffer to be developed with more than an order of magnitude smaller gain error. * Low Output Impedance . . . . . . . . . . . . . . . . . . . . . . . . 3 * Very High Slew Rate . . . . . . . . . . . . . . . . . . . . . 1300V/s * High Output Current. . . . . . . . . . . . . . . . . . . . . . . . . . 200mA * Pulsed Output Current . . . . . . . . . . . . . . . . . . . . . . 400mA * Monolithic Construction * Pb-Free Plus Anneal Available (RoHS Compliant) Applications * Line Driver The HA-5002 will provide many present hybrid users with a higher degree of reliability and at the same time increase overall circuit performance. * Data Acquistion For the military grade product, refer to the HA-5002/883 datasheet. * High Power Current Booster * 110MHz Buffer * Radara Cable Driver * High Power Current Source * Sample and Holds * Video Products Ordering Information PART NUMBER PART MARKING TEMP. RANGE (C) PACKAGE PKG. DWG. # HA2-5002-2 HA2-5002-2 -55 to 125 8 Pin Metal Can T8.C HA2-5002-5 HA2-5002-5 0 to 75 8 Pin Metal Can T8.C HA3-5002-5 HA3-5002-5 0 to 75 8 Ld PDIP E8.3 HA3-5002-5Z (Note) HA3-5002-5Z 0 to 75 8 Ld PDIP* (Pb-free) E8.3 HA4P5002-5 HA4P5002-5 0 to 75 20 Ld PLCC N20.35 HA4P5002-5Z (Note) HA4P5002-5Z 0 to 75 20 Ld PLCC (Pb-free) N20.35 HA9P5002-5 50025 0 to 75 8 Ld SOIC M8.15 HA9P5002-5Z (Note) 50025Z 0 to 75 8 Ld SOIC (Pb-free) M8.15 HA9P5002-9 50029 -40 to 85 8 Ld SOIC M8.15 HA9P5002-9Z (Note) 50029Z -40 to 85 8 Ld SOIC (Pb-free) M8.15 *Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing applications. NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright (c) Intersil Americas Inc. 2003-2006. All Rights Reserved. All other trademarks mentioned are the property of their respective owners. HA-5002 Pinouts V2- 2 7 V2+ NC 3 6 NC 4 5 V1- NC 3 2 1 20 19 IN 8 V1+ NC 4 18 NC V2- 5 17 V2+ NC 6 16 NC NC 7 15 NC NC 8 14 NC V2+ 1 7 2 NC V1- 6 5 3 V2- NC 4 OUT 2 10 11 12 13 NC V1- NC NOTE: Case Voltage = Floating 9 IN IN OUT OUT NC 8 V1+ 1 HA-5002 (METAL CAN) TOP VIEW NC V1+ HA-5002 (PLCC) TOP VIEW NC HA-5002 (PDIP, SOIC) TOP VIEW FN2921.11 March 8, 2006 HA-5002 Absolute Maximum Ratings Thermal Information Voltage Between V+ and V- Terminals. . . . . . . . . . . . . . . . . . . . 44V Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V1+ to V1Output Current (Continuous) . . . . . . . . . . . . . . . . . . . . . . . . 200mA Output Current (50ms On, 1s Off) . . . . . . . . . . . . . . . . . . . . 400mA Thermal Resistance (Typical, Note 2) JA (C/W) JC (C/W) PDIP Package*. . . . . . . . . . . . . . . . . . . 92 N/A Metal Can Package . . . . . . . . . . . . . . . 155 67 PLCC Package. . . . . . . . . . . . . . . . . . . 74 N/A SOIC Package . . . . . . . . . . . . . . . . . . . 157 N/A Max Junction Temperature (Hermetic Packages, Note 1) . . . . . . 175C Max Junction Temperature (Plastic Packages, Note 1) . . . . . . . . 150C Max Storage Temperature Range . . . . . . . . . . . . . . -65C to 150C Max Lead Temperature (Soldering 10s) . . . . . . . . . . . . . . . . 300C (PLCC and SOIC - Lead Tips Only) *Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing applications. Operating Conditions Temperature Range HA-5002-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55C to 125C HA-5002-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0C to 75C HA-5002-9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40C to 85C CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. Maximum power dissipation, including load conditions, must be designed to maintain the maximum junction temperature below 175C for the can packages, and below 150C for the plastic packages. 2. JA is measured with the component mounted on an evaluation PC board in free air. VSUPPLY = 12V to 15V, RS = 50, RL = 1k, CL = 10pF, Unless Otherwise Specified Electrical Specifications TEST CONDITIONS PARAMETER HA-5002-2 HA-5002-5, -9 TEMP (C) MIN TYP MAX MIN TYP MAX UNITS 25 - 5 20 - 5 20 mV INPUT CHARACTERISTICS Offset Voltage Full - 10 30 - 10 30 mV Average Offset Voltage Drift Full - 30 - - 30 - V/C Bias Current 25 - 2 7 - 2 7 A Full - 3.4 10 - 2.4 10 A Full 1.5 3 - 1.5 3 - M 10Hz-1MHz 25 - 18 - - 18 - VP-P RL = 50 25 - 0.900 - - 0.900 - V/V RL = 100 25 - 0.971 - - 0.971 - V/V Input Resistance Input Noise Voltage TRANSFER CHARACTERISTICS Voltage Gain (VOUT = 10V) -3dB Bandwidth RL = 1k 25 - 0.995 - - 0.995 - V/V RL = 1k Full 0.980 - - 0.980 - - V/V VIN = 1VP-P 25 - 110 - - 110 - MHz 25 - 40 - - 40 - A/mA AC Current Gain OUTPUT CHARACTERISTICS Output Voltage Swing RL = 100 25 10 10.7 - 10 11.2 - V RL = 1k, VS = 15V Full 10 13.5 - 10 13.9 - V RL = 1k, VS = 12V Full 10 10.5 - 10 10.5 - V mA VIN = 10V, RL = 40 Output Current Output Resistance VIN = 1VRMS, f = 10kHz Harmonic Distortion 25 - 220 - - 220 - Full - 3 10 - 3 10 25 - <0.005 - - <0.005 - % TRANSIENT RESPONSE Full Power Bandwidth (Note 3) 25 - 20.7 - - 20.7 - MHz Rise Time 25 - 3.6 - - 3.6 - ns ns Propagation Delay 25 - 2 - - 2 - Overshoot 25 - 30 - - 30 - % Slew Rate 25 1.0 1.3 - 1.0 1.3 - V/ns 25 - 50 - - 50 - ns Settling Time To 0.1% 3 FN2921.11 March 8, 2006 HA-5002 VSUPPLY = 12V to 15V, RS = 50, RL = 1k, CL = 10pF, Unless Otherwise Specified (Continued) Electrical Specifications TEST CONDITIONS PARAMETER HA-5002-2 HA-5002-5, -9 TEMP (C) MIN TYP MAX MIN TYP MAX UNITS Differential Gain RL = 500 25 - 0.06 - - 0.06 - % Differential Phase RL = 500 25 - 0.22 - - 0.22 - Degrees POWER REQUIREMENTS Supply Current AV = 10V Power Supply Rejection Ratio 25 - 8.3 - - 8.3 - mA Full - - 10 - - 10 mA Full 54 64 - 54 64 - dB NOTE: Slew Rate3. FPBW = -------------------------; V = 10V . 2V P EAK P Test Circuit and Waveforms +15V V2+ V1+ RS IN OUT V2- V1-15V RL FIGURE 1. LARGE AND SMALL SIGNAL RESPONSE VIN VIN VOUT VOUT RS = 50, RL = 100 RS = 50, RL = 1k SMALL SIGNAL WAVEFORMS SMALL SIGNAL WAVEFORMS 4 FN2921.11 March 8, 2006 HA-5002 Test Circuit and Waveforms (Continued) VIN VIN VOUT VOUT RS = 50, RL = 100 RS = 50, RL = 1k LARGE SIGNAL WAVEFORMS LARGE SIGNAL WAVEFORMS Schematic Diagram V1+ R8 R9 RN1 Q19 R4 Q26 Q20 Q25 R10 V2+ R1 Q18 Q12 Q3 Q9 Q1 Q27 Q6 Q10 R5 Q7 IN R11 Q4 OUT RN2 Q21 Q5 Q11 Q2 Q22 Q8 Q15 Q23 Q24 Q17 Q16 Q13 Q14 R7 R12 V2- R6 R2 R3 RN3 V1- Application Information Layout Considerations The wide bandwidth of the HA-5002 necessitates that high frequency circuit layout procedures be followed. Failure to follow these guidelines can result in marginal performance. Probably the most crucial of the RF/video layout rules is the use of a ground plane. A ground plane provides isolation and minimizes distributed circuit capacitance and inductance which will degrade high frequency performance. 5 Other considerations are proper power supply bypassing and keeping the input and output connections as short as possible which minimizes distributed capacitance and reduces board space. Power Supply Decoupling For optimal device performance, it is recommended that the positive and negative power supplies be bypassed with capacitors to ground. Ceramic capacitors ranging in value from 0.01 to 0.1F will minimize high frequency variations in supply voltage, while low frequency bypassing requires FN2921.11 March 8, 2006 HA-5002 Capacitive Loading larger valued capacitors since the impedance of the capacitor is dependent on frequency. The HA-5002 will drive large capacitive loads without oscillation but peak current limits should not be exceeded. Following the formula I = Cdv/dt implies that the slew rate or the capacitive load must be controlled to keep peak current below the maximum or use the current limiting approach as shown. The HA-5002 can become unstable with small capacitive loads (50pF) if certain precautions are not taken. Stability is enhanced by any one of the following: a source resistance in series with the input of 50 to 1k; increasing capacitive load to 150pF or greater; decreasing CLOAD to 20pF or less; adding an output resistor of 10 to 50; or adding feedback capacitance of 50pF or greater. Adding source resistance generally yields the best results. It is also recommended that the bypass capacitors be connected close to the HA-5002 (preferably directly to the supply pins). Operation at Reduced Supply Levels The HA-5002 can operate at supply voltage levels as low as 5V and lower. Output swing is directly affected as well as slight reductions in slew rate and bandwidth. Short Circuit Protection The output current can be limited by using the following circuit: VV+ R LIM = ------------------------- = -------------------------I OUTMAX I OUTMAX IOUTMAX = 200mA (CONTINUOUS) V+ V1+ RLIM V2+ OUT IN V2- V1- RLIM V1.8 MAXIMUM POWER DISSIPATION (W) 1.6 1.4 T JMAX - T A P DMAX = ------------------------------------------ JC + CS + SA PLCC PDIP 1.2 Where: TJMAX = Maximum Junction Temperature of the Device CAN 1.0 TA = Ambient 0.8 JC = Junction to Case Thermal Resistance SOIC 0.6 CS = Case to Heat Sink Thermal Resistance SA = Heat Sink to Ambient Thermal Resistance 0.4 QUIESCENT POWER DISSIPATION AT 15V SUPPLIES 0.2 Graph is based on: T JMAX - T A P DMAX = ------------------------------ JA 0.0 25 65 45 85 105 125 TEMPERATURE (C) FIGURE 2. MAXIMUM POWER DISSIPATION vs TEMPERATURE 6 FN2921.11 March 8, 2006 HA-5002 Typical Application +12V V1+ V2+ RS RM 50 50 VIN RG -58 VOUT VIN V1- RL 50 V2-12V VOUT FIGURE 3. COAXIAL CABLE DRIVER - 50 SYSTEM Typical Performance Curves 9 VS = 15V, RS = 50 GAIN 0 -3 PHASE -6 0 -9 45 -12 90 -15 135 -18 VOLTAGE GAIN (dB) 3 10 3 GAIN 0 -3 PHASE -6 0 -9 45 -12 90 -15 135 180 -18 180 1 VS = 15V, RS = 50 6 PHASE SHIFT VOLTAGE GAIN (dB) 6 1 100 10 FREQUENCY (MHz) 100 FREQUENCY (MHz) FIGURE 4. GAIN/PHASE vs FREQUENCY (RL = 1k) FIGURE 5. GAIN/PHASE vs FREQUENCY (RL = 50) 0.994 0.998 0.992 PHASE SHIFT 9 VS = 15V VS = 15V 0.997 VOLTAGE GAIN (V/V) VOLTAGE GAIN (V/V) 0.990 0.988 VOUT = -10V TO +10V 0.986 0.984 0.982 0.980 0.978 VOUT = 0 TO +10V 0.996 0.995 0.994 VOUT = 0 TO -10V 0.993 0.992 0.976 0.974 -60 -40 -20 0 20 40 60 TEMPERATURE (C) 80 100 120 FIGURE 6. VOLTAGE GAIN vs TEMPERATURE (RL = 100) 7 0.991 -60 -40 -20 0 20 40 60 80 100 120 TEMPERATURE (C) FIGURE 7. VOLTAGE GAIN vs TEMPERATURE (RL = 1k) FN2921.11 March 8, 2006 HA-5002 3 2 1 0 -1 -2 -3 -4 -5 -6 -7 -8 -9 -10 -11 -60 (Continued) 7 VS = 15V VS = 15V 6 BIAS CURRENT (A) OFFSET VOLTAGE (mV) Typical Performance Curves 5 4 3 2 1 0 -40 -20 0 20 40 60 80 100 -60 120 -40 -20 20 40 60 80 100 120 FIGURE 9. BIAS CURRENT vs TEMPERATURE FIGURE 8. OFFSET VOLTAGE vs TEMPERATURE 15 0 TEMPERATURE (C) TEMPERATURE (C) 10 VS = 15V, RLOAD = 100 VS = 15V, IOUT = 0mA 14 SUPPLY CURRENT (mA) OUTPUT VOLTAGE (V) 9 +VOUT -VOUT 13 12 8 7 6 5 4 11 -60 -40 -20 0 20 40 60 TEMPERATURE (C) 80 100 3 -60 120 FIGURE 10. MAXIMUM OUTPUT VOLTAGE vs TEMPERATURE -20 0 20 40 60 TEMPERATURE (C) 80 100 120 FIGURE 11. SUPPLY CURRENT vs TEMPERATURE 10 VS = 15V IOUT = 0mA 125C, 25C 100K 8 IMPEDANCE () SUPPLY CURRENT (mA) -40 -55C 6 4 ZIN 10K 1000 100 2 10 0 0 2 4 6 8 10 12 14 16 SUPPLY VOLTAGE (V) FIGURE 12. SUPPLY CURRENT vs SUPPLY VOLTAGE 8 18 1 100K ZOUT 1M 10M 100M FREQUENCY (Hz) FIGURE 13. INPUT/OUTPUT IMPEDANCE vs FREQUENCY FN2921.11 March 8, 2006 HA-5002 (Continued) 80 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 15 RLOAD = 100 70 60 PSRR (dB) VOUT MAX, VP-P AT 100kHz Typical Performance Curves TA = 25C TA = 125C, TA = -55C 50 40 30 20 10 12 8 SUPPLY VOLTAGE (V) 0 10K 5 1M FREQUENCY (Hz) 100M 10M FIGURE 15. PSRR vs FREQUENCY FIGURE 14. VOUT MAXIMUM vs VSUPPLY 1500 150 1400 100 VOUT - VIN (mV) SLEW RATE (V/s) 100K 1300 1200 1100 VS = 15V TA = 25C RL = 100 50 RL = 1K 0 -50 RL = 600 1000 -100 900 6 8 10 12 14 SUPPLY VOLTAGE (V) 16 FIGURE 16. SLEW RATE vs SUPPLY VOLTAGE 18 -150 -10 -8 -6 -4 -2 0 2 4 INPUT VOLTAGE (VOLTS) 6 8 10 FIGURE 17. GAIN ERROR vs INPUT VOLTAGE Die Characteristics SUBSTRATE POTENTIAL (POWERED UP): V1TRANSISTOR COUNT: 27 PROCESS: Bipolar Dielectric Isolation 9 FN2921.11 March 8, 2006 HA-5002 Metallization Mask Layout HA-5002 IN V1- V1- (ALT) V1+ (ALT) V2+ V2- V1+ OUT 10 FN2921.11 March 8, 2006 HA-5002 Dual-In-Line Plastic Packages (PDIP) E8.3 (JEDEC MS-001-BA ISSUE D) N 8 LEAD DUAL-IN-LINE PLASTIC PACKAGE E1 INDEX AREA 1 2 3 INCHES N/2 -B- -AD E BASE PLANE -C- A2 SEATING PLANE A L D1 e B1 D1 A1 eC B 0.010 (0.25) M C A B S MILLIMETERS SYMBOL MIN MAX MIN MAX NOTES A - 0.210 - 5.33 4 A1 0.015 - 0.39 - 4 A2 0.115 0.195 2.93 4.95 - B 0.014 0.022 0.356 0.558 - C L B1 0.045 0.070 1.15 1.77 8, 10 eA C 0.008 0.014 0.204 C D 0.355 0.400 9.01 eB NOTES: 1. Controlling Dimensions: INCH. In case of conflict between English and Metric dimensions, the inch dimensions control. 0.005 - 0.13 - 5 E 0.300 0.325 7.62 8.25 6 E1 0.240 0.280 6.10 7.11 5 e 0.100 BSC eA 0.300 BSC 3. Symbols are defined in the "MO Series Symbol List" in Section 2.2 of Publication No. 95. eB - L 0.115 5. D, D1, and E1 dimensions do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.010 inch (0.25mm). 6. E and eA are measured with the leads constrained to be perpendicular to datum -C- . 5 D1 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 4. Dimensions A, A1 and L are measured with the package seated in JEDEC seating plane gauge GS-3. 0.355 10.16 N 8 2.54 BSC 7.62 BSC 0.430 - 0.150 2.93 10.92 3.81 8 6 7 4 9 Rev. 0 12/93 7. eB and eC are measured at the lead tips with the leads unconstrained. eC must be zero or greater. 8. B1 maximum dimensions do not include dambar protrusions. Dambar protrusions shall not exceed 0.010 inch (0.25mm). 9. N is the maximum number of terminal positions. 10. Corner leads (1, N, N/2 and N/2 + 1) for E8.3, E16.3, E18.3, E28.3, E42.6 will have a B1 dimension of 0.030 - 0.045 inch (0.76 - 1.14mm). 11 FN2921.11 March 8, 2006 HA-5002 Metal Can Packages (Can) T8.C MIL-STD-1835 MACY1-X8 (A1) REFERENCE PLANE A 8 LEAD METAL CAN PACKAGE e1 L L2 L1 INCHES SYMBOL OD2 0.185 4.19 4.70 - 0.019 0.41 0.48 1 Ob1 0.016 0.021 0.41 0.53 1 N Ob2 0.016 0.024 0.41 0.61 - OD 0.335 0.375 8.51 9.40 - OD1 0.305 0.335 7.75 8.51 - OD2 0.110 0.160 2.79 4.06 - 1 Ob k C L e BASE AND SEATING PLANE Q BASE METAL Ob1 NOTES 0.165 k1 Ob1 MAX 0.016 Oe F MIN A A 2 MILLIMETERS MAX Ob A OD OD1 MIN e1 LEAD FINISH Ob2 SECTION A-A NOTES: 1. (All leads) Ob applies between L1 and L2. Ob1 applies between L2 and 0.500 from the reference plane. Diameter is uncontrolled in L1 and beyond 0.500 from the reference plane. 2. Measured from maximum diameter of the product. 3. is the basic spacing from the centerline of the tab to terminal 1 and is the basic spacing of each lead or lead position (N -1 places) from , looking at the bottom of the package. 0.200 BSC 5.08 BSC 0.100 BSC - 2.54 BSC - F - 0.040 - 1.02 - k 0.027 0.034 0.69 0.86 - k1 0.027 0.045 0.69 1.14 2 12.70 19.05 1 1.27 1 L 0.500 0.750 L1 - 0.050 - L2 0.250 - 6.35 - 1 Q 0.010 0.045 0.25 1.14 - 45o BSC 45o BSC 45o BSC 45o BSC N 8 8 3 3 4 Rev. 0 5/18/94 4. N is the maximum number of terminal positions. 5. Dimensioning and tolerancing per ANSI Y14.5M - 1982. 6. Controlling dimension: INCH. 12 FN2921.11 March 8, 2006 HA-5002 Plastic Leaded Chip Carrier Packages (PLCC) 0.042 (1.07) 0.048 (1.22) PIN (1) IDENTIFIER N20.35 (JEDEC MS-018AA ISSUE A) 0.042 (1.07) 0.056 (1.42) 0.004 (0.10) C 0.025 (0.64) R 0.045 (1.14) 0.050 (1.27) TP C L D2/E2 C L E1 E D2/E2 VIEW "A" 0.020 (0.51) MIN A1 A D1 D 20 LEAD PLASTIC LEADED CHIP CARRIER PACKAGE INCHES MILLIMETERS SYMBOL MIN MAX MIN MAX NOTES A 0.165 0.180 4.20 4.57 - A1 0.090 0.120 2.29 3.04 - D 0.385 0.395 9.78 10.03 - D1 0.350 0.356 8.89 9.04 3 D2 0.141 0.169 3.59 4.29 4, 5 E 0.385 0.395 9.78 10.03 - E1 0.350 0.356 8.89 9.04 3 E2 0.141 0.169 3.59 4.29 4, 5 N 20 20 6 Rev. 2 11/97 SEATING -C- PLANE 0.020 (0.51) MAX 3 PLCS 0.026 (0.66) 0.032 (0.81) 0.013 (0.33) 0.021 (0.53) 0.025 (0.64) MIN 0.045 (1.14) MIN VIEW "A" TYP. NOTES: 1. Controlling dimension: INCH. Converted millimeter dimensions are not necessarily exact. 2. Dimensions and tolerancing per ANSI Y14.5M-1982. 3. Dimensions D1 and E1 do not include mold protrusions. Allowable mold protrusion is 0.010 inch (0.25mm) per side. Dimensions D1 and E1 include mold mismatch and are measured at the extreme material condition at the body parting line. 4. To be measured at seating plane -C- contact point. 5. Centerline to be determined where center leads exit plastic body. 6. "N" is the number of terminal positions. 13 FN2921.11 March 8, 2006 HA-5002 Small Outline Plastic Packages (SOIC) M8.15 (JEDEC MS-012-AA ISSUE C) N INDEX AREA 8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE H 0.25(0.010) M B M INCHES E SYMBOL -B1 2 A 3 L SEATING PLANE -A- A D h x 45 -C- e A1 B 0.25(0.010) M C 0.10(0.004) C A M B S MIN MAX MIN MAX NOTES 0.0532 0.0688 1.35 1.75 - A1 0.0040 0.0098 0.10 0.25 - B 0.013 0.020 0.33 0.51 9 C 0.0075 0.0098 0.19 0.25 - D 0.1890 0.1968 4.80 5.00 3 E 0.1497 0.1574 3.80 4.00 4 e 0.050 BSC 1.27 BSC - H 0.2284 0.2440 5.80 6.20 - h 0.0099 0.0196 0.25 0.50 5 L 0.016 0.050 0.40 N NOTES: MILLIMETERS 8 0 1.27 8 8 0 6 7 8 1. Symbols are defined in the "MO Series Symbol List" in Section 2.2 of Publication Number 95. Rev. 1 6/05 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension "E" does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. "L" is the length of terminal for soldering to a substrate. 7. "N" is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width "B", as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch). 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation's quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 14 FN2921.11 March 8, 2006