EA5070 Series
Revised B: 12/1/2015
Page 2 of 10 www.ecliptek.com
REGULATORY COMPLIANCE
2011/65 + 191 SVHC
2015/863
ITEM DESCRIPTION
Quartz Crystal Resonator 5.0mm x 7.0mm x 1.3mm 4 Pad Ceramic Surface Mount (SMD)
ELECTRICAL SPECIFICATIONS
Nominal Frequency
6MHz to 66MHz
Frequency Tolerance/Stability
±50ppm at 25°C, ±100ppm over 0°C to +70°C
±50ppm at 25°C, ±100ppm over
-20°C to +70°C
±50ppm at 25°C, ±100ppm over
-40°C to +85°C
±30ppm at 25°C, ±50ppm over 0°C to +70°C
±30ppm at 25°C, ±50ppm over
-20°C to +70°C
±30ppm at 25
°C, ±50ppm over -40°C to +85°C
±15ppm at 25°C, ±30ppm over 0°C to +70°C
±15ppm at 25°C, ±30ppm over
-20°C to +70°C
±15ppm at 25°C, ±30ppm over
-40°C to +85°C
±15ppm at 25°C, ±20ppm over 0°C to +70°C
±15ppm at 25°C, ±20ppm over
-20°C to +70°C
±15ppm at 25°C
, ±20ppm over -40°C to +85°C
±10ppm at 25°C, ±15ppm over 0°C to +70°C
±10ppm at 25°C, ±15ppm over -20°C to +70°C
Aging at 25°C
±3ppm/year Maximum
Load Capacitance
Series Resonant, 12pF Parallel Resonant to 50pF Parallel Resonant
Shunt Capacitance
7pF Maximum
Equivalent Series Resistance
See the Equivalent Series Resistance (ESR), Mode of Operation, and Crystal Cut Table Below
Mode of Operation
AT-Cut Fundamental (Only available over Nominal Frequency range of 6MHz to 40MHz)
AT-Cut Third Overtone (Only available over Nominal Frequency range of 35.328MHz to 66MHz)
Drive Level
50µWatts Maximum
Spurious Response
Measured from Fo to Fo +5000ppm
-3dB Minimum
Storage Temperature Range
-40°C to +85°C
Insulation Resistance
Measured at 100Vdc
500 Megaohms Minimum
EQUIVALENT SERIES RESISTANCE (ESR), MODE OF OPERATION AND CRYSTAL CUT
Frequency Range
ESR (Ohms Max)
Mode
Frequency Range
ESR (Ohms Max)
Mode
6MHz to 9.999999MHz 90 AT-Cut Fundamental 16MHz to 40MHz 30 AT-Cut Fundamental
10MHz to 10.999999MHz 60 AT-Cut Fundamental 35.328MHz to 39.999999MHz 100 AT-Cut Third Overtone
11MHz to 13.999999MHz 50 AT-Cut Fundamental 40MHz to 59.999999MHz 80 AT-Cut Third Overtone
14MHz to 15.999999MHz
40
AT-Cut Fundamental
60MHz to 66MHz
80
AT-Cut Third Overtone
EA5070 Series
RECOMMENDED SOLDER REFLOW METHOD
Revised B: 12/1/2015
Page 6 of 10 www.ecliptek.com
HIGH TEMPERATURE INFRARED/CONVECTION
T
S
MAX to T
L
(Ramp-up Rate)
3°C/Second Maximum
Preheat
-
Temperature Minimum (TS MIN)
-
Temperature Typical (TS TYP)
-
Temperature Maximum(TS MAX)
-
Time (tS)
150°C
175°C
200°C
60
- 180 Seconds
Ramp-up Rate (T
L
to T
P
)
3°C/Second Maximum
Time Maintained Above:
-
Temperature (TL)
-
Time (tL)
217°C
60
- 150 Seconds
Peak Temperature (TP)
260°C Maximum for 10 Seconds Maximum
Target Peak Temperature(T
P
Target)
250°C +0/-5°C
Time within 5°C of actual peak (t
p
)
20 - 40 Seconds
Ramp-down Rate
6°C/Second Maximum
Time 25°C to Peak Temperature (t)
8 Minutes Maximum
Moisture Sensitivity Level
Level 1
Additional Notes
Temperatures shown are applied to body of device.
High Temperature Manual Soldering
260°C Maximum for 5 Seconds Maximum, 2 times Maximum. (Temperatures shown are applied to body of device.)
EA5070 Series
RECOMMENDED SOLDER REFLOW METHOD
Revised B: 12/1/2015
Page 7 of 10 www.ecliptek.com
LOW TEMPERATURE INFRARED/CONVECTION
T
S
MAX to T
L
(Ramp-up Rate)
5°C/Second Maximum
Preheat
-
Temperature Minimum (Ts MIN)
-
Temperature Typical (Ts TYP)
-
Temperature Maximum(Ts MAX)
-
Time (ts)
N/A
150°C
N/A
30
- 60 Seconds
Ramp-up Rate (T
L
to T
P
)
5°C/Second Maximum
Time Maintained Above:
-
Temperature (TL)
-
Time (tL)
150°C
200 Seconds Maximum
Peak Temperature (TP)
245°C Maximum
Target Peak Temperature (T
P
Target)
245°C Maximum 2 Times / 230˚C Maximum 1 Time
Time within 5°C of actual peak (t
p
)
10 Seconds Maximum 2 Times / 80 Seconds Maximum 1 Time
Ramp-down Rate
5°C/Second Maximum
Time 25°C to Peak Temperature (t)
N/A
Moisture Sensitivity Level
Level 1
Additional Notes
Temperatures shown are applied to body of device.
Low Temperature Manual Soldering
185°C Maximum for 10 Seconds Maximum, 2 times Maximum. (Temperatures shown are applied to body of device.)
