Vertical Male Connectors Type C For Backplanes 55 signal contacts 25 mm extension module The ERmet type C vertical male connector provides 55 signal contacts and 22 ground shield contacts in 5+2 row x 11 position, fully loaded configuration. With 15 different standard pin lengths to choose from, this is one of the most versatile connectors available. The connector is designed for gas tight pressfit installation. The ERmet type C vertical male connector incorporates pre-alignment guides but has no multi function cavity. This connector is designed to be used alone or in conjunction with either type B, L, M or N ERmet connectors, however it can only be installed at the lower end of a connector row. Dimensional drawings and board hole pattern date 15.4 130 2 2 10 x 2 = 20 4x2= 13.45 8 compliant zone for thru hole 0.60.00.05 1 11 z a b c d e f 3.7 1 max 25 max Board hole pattern (Component mounting side) 10 x 2 = 0.1 all holes 2 2 + 0.05 not plated thru 3 11 0.6 1 + 0.05 - plated thru drill hole 0.7 0.02 z a b c d e f ( 12 ) 2 ( 20 ) 6x2= Note: The numbering on the connectors themselves is in accordance with the IEC 61076-4-101 standard. All dimensions in mm. 3- 0.1 - 0.1 Id.-Nr. class Catalog E 074482 08/06 Edition 4 www.erni.com Vertical Male Connectors Type C For Backplanes Ordering Information Configuration Used For Part Number ERmet 2.0mm No. of Pins Type C Without Shield, With Peg 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f 55 043138 55 044147 77 054546 77 053009 Type C Without Shield, With Peg 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Type C With Shield, Without Peg 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Type C With Shield, With Peg 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Contact versions ERNI can accommodate any pattern of male connector contact loading. For shield rows z and f (7 row connectors) or z and y (10 row connectors), level 3 contacts should be specified. For rear I/O and shrouds, choose contacts with the R1, R2 or R3 terminal length. Each contact has a unique letter designation. Use this letter designation when filling in the contact loading requirements on the ERNI Customer Request Form. Catalog E 074482 08/06 Edition 4 www.erni.com 131 Vertical Male Connectors Type C For Backplanes Ordering Information Configuration Used For No. of Pins Part Number Type C Without Shield, With Peg And With Extended Terminals 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f 55 054129 77 064550 77 064572 77 103926 Type C With Shield, With Peg And With Extended Terminals 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Type C With Shield, With Peg And With Extended Terminals 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Type C With Shield, With Peg And With Extended Terminals 11 10 9 8 7 6 5 4 3 2 1 z a b c d e f Contact versions ERNI can accommodate any pattern of male connector contact loading. For shield rows z and f (7 row connectors) or z and y (10 row connectors), level 3 contacts should be specified. For rear I/O and shrouds, choose contacts with the R1, R2 or R3 terminal length. Each contact has a unique letter designation. Use this letter designation when filling in the contact loading requirements on the ERNI Customer Request Form. 132 Catalog E 074482 08/06 Edition 4 www.erni.com