ACDC 3501200 Watts SHP Series xppower.com * Rugged Industrial Construction * Variable Fan Speed for Noise Reduction * 40 C to +70 C Operation * AC OK, Remote On/Off and Active Current Share * 5 V Standby * Screw Terminals * 3 Year Warranty Specification Input * 650 W: 80-264 VAC, derate output power 10% <90 VAC, and 20% <85 VAC 350 & 1000 W: 85-264 VAC, derate output power 10% <90 VAC Input Frequency * 47-63 Hz Input Current * 350 W: 3.8 A typical at 115 VAC, 2.1 A typical at 230 VAC, 650 W: 6.5 A typical at 115 VAC, 3.2 A typical at 230 VAC, 1000 W: 10.9 A typical at 115 VAC, 5.1 A typical at 230 VAC Inrush Current * 650 W: 40 A max at 264 VAC 350 & 1000 W: 60 A max at 264 VAC Power Factor * >0.9 Earth Leakage Current * 0.5 mA max 264 VAC/60 Hz(1) Input Protection * 350W: T10 A/250 V, 650W: T16 A/250 V, 1000W: T20 A/250 V internal fuse in line and neutral, 350W: single internal fuse in line. Input Voltage Output * 12-48 VDC (see tables) * 10% V1 * 650 W: 1% V1, 5% V3, 350 & 1000 W: 1% V1, 5% V2 Minimum Load * No minimum load required Start Up Delay * 500 ms max Start Up Rise Time * 50 ms typical Hold Up Time * 20 ms minimum Drift * 0.2% after 20 min warm up Line Regulation * 0.5% Load Regulation * 650 W: 1% V1, 5% V3, 350 & 1000 W: 1% V1, 5% V2 Transient Response * 4% max. deviation, recovery to within 1% in 500 s for a 50-75-50% load change Ripple & Noise * 1% pk-pk typical V1, 20 MHz bandwidth Overvoltage Protection * 115-145% Vnom, recycle input to reset Overload Protection * 110-140%, V1 only Overtemperature * Auto reset Protection Short Circuit Protection * Constant current characteristic (1) Temp. Coefficient * 0.05% / C Remote Sense * Compensates for 0.5 V total voltage drop Remote On/Off * Uncommitted isolated optocoupler diode, powered diode inhibits V1 and fan supply (1) Current Share * Single wire current share (1) Output Voltage Output Voltage Trim Initial Set Accuracy (1) See longform datasheet for more information General Efficiency Isolation Switching Frequency Power Density Signals MTBF * 85% typical * 3000 VAC input to output, 1500 VAC input to ground, 500 VDC output to ground * PFC 70 kHz, main converter 200 kHz, standby 130 kHz typical * 350 W: 6.6 W/in3, 650 W: 8.2 W/in3, 1000 W: 8.9 W/in3 * AC OK, remote on/off, current share (1) * 216-275 KHrs to MIL-HDBK-217F at 25 C, GB(1) Environmental Operating Temperature * -20 C to +70 C, derate linearly from +50 C at 2.5% / C to 50% at +70 C, -40 C start up (1) Cooling * 650 W: Forced cooled, `-TF' & `-EF' models have integral dual voltage level fan, which is load dependant, U Channel requires 5.5 m/s minimum airflow, 350 & 1000 W: Forced cooled via integral multi voltage level fan which is load dependant (1) Operating Humidity * 95% RH, non-condensing Storage Temperature * -40 C to +85 C Operating Altitude * 3000 m Shock * 30 g pk, half sine, 6 axes EN60068-2-27, -2-47 Vibration * 2 g rms, 5-500 kHz, 3 axes EN60068-2-6 EMC & Safety Emissions Harmonic Currents Voltage Flicker ESD Immunity Radiated Immunity EFT/Burst Surge Conducted Immunity Dips & Interruptions Safety Approvals * EN55022 class B conducted EN55022 class A radiated * EN61000-3-2 class A, 650 W: class C for loads 20% 350 & 1000 W: class C for loads 10% * EN61000-3-3 * EN61000-4-2, level 3 contact, level 3 air, Perf Criteria A * EN61000-4-3, level 3 Perf Criteria A * EN61000-4-4, level 3 Perf Criteria A * EN61000-4-5, installation class 3, Perf Criteria A * EN61000-4-6, level 3, Perf Criteria A * EN61000-4-11, 30% 10 ms, 60% 100 ms, 100% 5000 ms, Perf Criteria A, B, B * IEC60950-1 CB report, CSA 22.2 No. 60950-1, UL60950-1, TUV, EN60950-1, SEMI F47 Output Voltage V1 12 15 24 28 36 48 Output Current V1 V V V V V V Standby Supply V2 26.5 A 22.0 A 14.5 A 12.5 A 9.7 A 7.3 A 5 5 5 5 5 5 V V V V V V / / / / / / 0.2 0.2 0.2 0.2 0.2 0.2 A A A A A A Output Power Continuous Peak 318 W 330 W 348 350 350 350 W W W W 417 420 420 420 W W W W Model Number SHP350PS12 SHP350PS15 SHP350PS24 SHP350PS28 SHP350PS36 SHP350PS48 Notes 1. Peak power available for 10 seconds with 35% duty cycle. Mechanical Details End Fan Standard Terminal Block M3.5 Screw 3 Pins 0.37 (9.5) Centre Standard Terminal Block M4 Screw 4 Pins 0.37 (9.5) Centre 2.1 (53.34) L -VOUT N +VOUT LED 2.20 (55.9) B 1.13 (28.72) VR 1.03 (26.2) 0.06 (1.5) 7.00 (177.8) A Mounting Hole 8 places M3 x 0.5 0.15 (3.8) Max. Penetration PIN 2 PIN 1 PIN 10 PIN 9 A A AIRFLOW 1.61 (41.0) -2X DETAIL B SCALE 2 : 1 LOGIC CONNECTOR J3 A A 2.44 (62.0) CL 3.6 (91.44) A A 5.35 (136.0) 0.70 (17.9) Notes 1. Dimensions shown in inches (mm). 2. Weight: 1.73 lb (0.788 kg). 3. Logic connector J3 mates with JST housing PHDR-10VS and SPHD-001T-P0.5 Crimp Terminals J3 Logic Connector (JST B10B-PHDSS) Pin Function 1 + Sense 2 - Sense 3 AC OK/Power Fail 4 - Sense 5 Current Share 6 Current Share 7 + Inhibit 8 - Inhibit 9 +5 V Standby 10 5 V Standby Return ACDC SHP350 Models and Ratings Output Voltage V1 12 15 24 28 36 48 Output Current V1 V V V V V V 50.0 40.0 27.0 23.0 18.0 13.5 Fan Supply V2(4) A A A A A A 12 12 12 12 12 12 V V V V V V / / / / / / 0.5 0.5 0.5 0.5 0.5 0.5 Standby Supply V3 A A A A A A 5 5 5 5 5 5 V V V V V V / / / / / / 0.2 0.2 0.2 0.2 0.2 0.2 Output Power(3) A A A A A A 607 607 655 655 655 655 W W W W W W Model Number(1,2) SHP650PS12-EF SHP650PS15-EF SHP650PS24-EF SHP650PS28-EF SHP650PS36-EF SHP650PS48-EF Notes 1. For top fan version replace `-EF' in model number with `-TF', e.g. SHP650PS12-TF 2. For U Channel version remove suffix. 3. U Channel models require a minimum of 5.5 m/s airflow from the system. 4. Not available for `-TF' and `-EF' models as used by integral fan. Mechanical Details End Fan (See Longform Datasheet for UChannel Version) Standard Terminal Block, M4 Screw, 6 Pins, 9.5 mm Center torque 10.62 lbs-in (1.2 Nm) L Vo+ Standard Terminal Block, M3.5 Screw 3 Pins 9.5 mm Center torque 10.62 lbs-in (1.2 Nm) E N Vo- ACDC SHP650 Models and Ratings 2.49 (63.3) V1 Adjustment Output On, LED 9.18 (233.2) 2 x M3 THD both side faces 0.15 (3.8) max screw penetration max torque 4.0-5.0 lbs-in (0.45-0.57 Nm) 2.50 (63.5) AIRFLOW Pin 2 Pin 1 Pin 10 Pin 9 1.95 (49.5) J3: Logic Connector 8.00 (203.2) 2.86 (72.6) 4.00 (101.6) CL 4 x M3 THD 0.15 (3.8) max screw penetration max torque 4.0-5.0 lbs-in (0.45-0.57 Nm) 6.53 (165.8) 0.87 (22.2) Notes 1. Dimensions shown in inches (mm). 2. Weight: 2.8 lb (1.27 kg). 3. J3 Mating Plug: JST part no. PHR-2, contact: JST part no. SPH-002T-P0.5S; J3 Mating Plug: JST part no. PHDR-10VS, contact: 26-22AWG JST part no. SPHD-001T-P0.5 J3 Logic Connector (JST B10B-PHDSS) Pin Function 1 + Sense 2 - Sense 3 AC OK/Power Fail 4 - Sense 5 Current Share 6 Current Share 7 + Inhibit 8 - Inhibit 9 +5 V Standby (V3) 10 5 V Standby Return (V3) Top Fan (Suffix TF) Standard Terminal Block, M3.5 Screw 3, Pins 9.5 mm Center torque 10.62 lbs-in (1.2 Nm) Standard Terminal Block, M4 Screw, 6 Pins, 9.5 mm Center torque 10.62 lbs-in (1.2 Nm) Vo+ L E Vo- N V1 Adjustment Output On, LED 2.50 (63.5) 8.00 (203.2) 2.58 (65.5) AIRFLOW 2 x M3 THD both side faces 0.15 (3.8) max screw penetration max torque 4.0-5.0 lbs-in (0.45-0.57 Nm) 1.95 (49.5) Pin 2 Pin 1 Pin 10 pin 9 J3: Logic Connector 2.86 (72.6) 4.00 (101.6) 4 x M3 THD 0.15 (3.8) max screw penetration max torque 4.0-5.0 lbs-in (0.45-0.57 Nm) Pin 1 2 3 4 5 6 7 8 9 10 0.87 (22.2) 6.53 (165.8) Notes 1. Dimensions shown in inches (mm). 2. Weight: 2.8 lb (1.27 kg). 3. J3 Mating plug: JST part no. PHDR-10VS, contact: 26-22 AWG JST part no. SPHD-001T-P0.5. J3 Logic Connector (JST B10B-PHDSS) Function + Sense - Sense AC OK/Power Fail - Sense Current Share Current Share + Inhibit - Inhibit +5 V Standby (V3) 5 V Standby Return (V3) Signals AC OK/Power Fail Remote On/Off (Inhibit) INHIBIT HI POWER SUPPLY Max 12 V 20 mA 5 V Standby Pin 9 330R 5 V Standby Pin 9 5 V Standby Pin 9 2-5 mA 100 R 2-5 mA Inhibit Hi Pin 7 AC OK Collector Pin 3 AC OK Emitter Pin 2 (-sense) INHIBIT LOW 800 R POWER SUPPLY 800 R Transistor On (<0.8 V): AC NOT OK Transistor Off (>4.5 V): AC OK Inhibit Lo Pin 8 5 V Standby Return Pin 10 5 V Standby Return Pin 10 Chassis J3 Logic Connector J3 Logic Connector Signal 100 R Inhibit Hi Pin 7 Inhibit Lo Pin 8 5 V Standby Return Pin 10 POWER SUPPLY High: Power Supply OFF Low or Floating: Power Supply ON For U Channel and Thermal Considerations please see longform datasheet. Chassis J3 Logic Connector Signal High: Power Supply ON Low or Floating: Power Supply OFF ACDC SHP650 Mechanical Details Output Current V1 <180 VAC Output Power Standby Supply V2 >180 VAC <180 VAC Model Number >180 VAC 12 V 83.0 A 5 V / 1.0 A 1000 W 15 V 67.0 A 5 V / 1.0 A 1010 W SHP1000PS12 SHP1000PS15 24 V 42.0 A 50.0 A 5 V / 1.0 A 1013 W 1200 W SHP1000PS24 28 V 36.0 A 43.0 A 5 V / 1.0 A 1013 W 1200 W SHP1000PS28 36 V 28.0 A 34.0 A 5 V / 1.0 A 1013 W 1200 W SHP1000PS36 48 V 21.0 A 25.0 A 5 V / 1.0 A 1013 W 1200 W SHP1000PS48 Mechanical Details VO- Standard Terminal Block, M6 Screw, 4 Pins 0.62 (16.0) center Torque 26.0 lbs-in (2.94 Nm) VO+ ACDC Output Voltage V1 5.90 (149.8) 2.91 (73.9) Output On, LED A V1 Adjustment N 1.47 (37.4) L 2.40 (61.0) 9.48 (240.9) 1.20 (30.5) 9.55 (242.64) Standard Terminal Block, M4 Screw 3 Pins 0.37 (9.5) center Torque 10.62 lbs-in (1.2 Nm) 9.41 (238.9) 4 x M4-0.7 THD both side faces 0.15 (3.8) max screw penetration max torque 10.62 lbs-in (1.2 Nm) B B Airflow 1.20 (30.5) 4 x M4-0.7 THD both side faces 0.15 (3.8) max screw penetration max torque 10.62 lbs-in (1.2 Nm) B B 4.50 (114.3) CL Pin 2 Pin 1 Pin 10 Pin 9 B B Detail A J3: Logic Connector 6.70 (170.2) 1.33 (33.8) Notes 1. Dimensions shown in inches (mm). 2. Weight: 4.6 lb (2.08 kg) 3. J3 Mating Plug: JST part no. PHDR-10VS, contact: 26-22AWG JST part no. SPHD-001T-P0.5 J3 Logic Connector (JST B10B-PHDSS) Pin Function 1 + Sense 2 - Sense 3 AC OK/Power Fail 4 - Sense 5 Current Share 6 Current Share 7 + Inhibit 8 - Inhibit 9 +5 V Standby 10 -5 V Standby 21-Oct-13 ACDC SHP1000 Models and Ratings