ACDC
Specification
3501200 Watts
•Rugged Industrial Construction
•Variable Fan Speed for Noise Reduction
•40 °C to +70 °C Operation
•AC OK, Remote On/Off and Active Current Share
•5 V Standby
•Screw Terminals
•3 Year Warranty
SHP Series
Input
Input Voltage • 650 W: 80-264 VAC, derate output power
10% <90 VAC, and 20% <85 VAC
350 & 1000 W: 85-264 VAC, derate output
power 10% <90 VAC
Input Frequency • 47-63 Hz
Input Current • 350 W: 3.8 A typical at 115 VAC,
2.1 A typical at 230 VAC,
650 W: 6.5 A typical at 115 VAC,
3.2 A typical at 230 VAC,
1000 W: 10.9 A typical at 115 VAC,
5.1 A typical at 230 VAC
Inrush Current • 650 W: 40 A max at 264 VAC
350 & 1000 W: 60 A max at 264 VAC
Power Factor • >0.9
Earth Leakage Current • 0.5 mA max 264 VAC/60 Hz(1)
Input Protection • 350W: T10 A/250 V, 650W: T16 A/250 V,
1000W: T20 A/250 V internal fuse in line and
neutral, 350W: single internal fuse in line.
Output
Output Voltage • 12-48 VDC (see tables)
Output Voltage Trim • ±10% V1
Initial Set Accuracy • 650 W: ±1% V1, ±5% V3,
350 & 1000 W: ±1% V1, ±5% V2
Minimum Load • No minimum load required
Start Up Delay • 500 ms max
Start Up Rise Time • 50 ms typical
Hold Up Time • 20 ms minimum
Drift • ±0.2% after 20 min warm up
Line Regulation • ±0.5%
Load Regulation • 650 W: ±1% V1, ±5% V3,
350 & 1000 W: ±1% V1, ±5% V2
Transient Response • 4% max. deviation, recovery to
within 1% in 500 µs for a 50-75-50%
load change
Ripple & Noise • 1% pk-pk typical V1, 20 MHz bandwidth
Overvoltage Protection • 115-145% Vnom, recycle input to reset
Overload Protection • 110-140%, V1 only
Overtemperature • Auto reset
Protection
Short Circuit Protection • Constant current characteristic (1)
Temp. Coefficient • 0.05% / °C
Remote Sense • Compensates for 0.5 V total voltage drop
Remote On/Off • Uncommitted isolated optocoupler diode,
powered diode inhibits V1 and fan supply(1)
Current Share • Single wire current share (1)
(1) See longform datasheet for more information
xppower.com
General
Efficiency • 85% typical
Isolation • 3000 VAC input to output, 1500 VAC input
to ground, 500 VDC output to ground
Switching Frequency • PFC 70 kHz, main converter 200 kHz,
standby 130 kHz typical
Power Density • 350 W: 6.6 W/in3, 650 W: 8.2 W/in3,
1000 W: 8.9 W/in3
Signals • AC OK, remote on/off, current share (1)
MTBF • 216-275 KHrs to MIL-HDBK-217F at 25 °C,
GB(1)
Environmental
Operating Temperature • -20 °C to +70 °C, derate linearly from
+50 °C at 2.5% / °C to 50% at +70 °C,
-40 °C start up (1)
Cooling • 650 W: Forced cooled, ‘-TF’ & ‘-EF’ models
have integral dual voltage level fan, which is
load dependant, U Channel requires 5.5 m/s
minimum airflow, 350 & 1000 W: Forced cooled
via integral multi voltage level fan which is load
dependant (1)
Operating Humidity • 95% RH, non-condensing
Storage Temperature • -40 °C to +85 °C
Operating Altitude • 3000 m
Shock • 30 g pk, half sine, 6 axes EN60068-2-27, -2-47
Vibration • 2 g rms, 5-500 kHz, 3 axes EN60068-2-6
EMC & Safety
Emissions • EN55022 class B conducted
EN55022 class A radiated
Harmonic Currents • EN61000-3-2 class A,
650 W: class C for loads ≥20%
350 & 1000 W: class C for loads ≥10%
Voltage Flicker • EN61000-3-3
ESD Immunity • EN61000-4-2, level 3 contact, level 3 air,
Perf Criteria A
Radiated Immunity • EN61000-4-3, level 3 Perf Criteria A
EFT/Burst • EN61000-4-4, level 3 Perf Criteria A
Surge • EN61000-4-5, installation class 3,
Perf Criteria A
Conducted Immunity • EN61000-4-6, level 3, Perf Criteria A
Dips & Interruptions • EN61000-4-11, 30% 10 ms,
60% 100 ms, 100% 5000 ms,
Perf Criteria A, B, B
Safety Approvals • IEC60950-1 CB report, CSA 22.2
No. 60950-1, UL60950-1, TUV,
EN60950-1, SEMI F47
ACDC
SHP350
Models and Ratings
1. Dimensions shown in inches (mm).
2. Weight: 1.73 lb (0.788 kg).
3. Logic connector J3 mates with JST housing PHDR-10VS
and SPHD-001T-P0.5 Crimp Terminals
Notes
7.00 (177.8)
2.20
(55.9)
A Mounting Hole
8 places M3 x 0.5
0.15 (3.8) Max. Penetration
0.06 (1.5)
Standard Terminal Block
M4 Screw 4 Pins
0.37 (9.5) Centre
Standard Terminal Block
M3.5 Screw 3 Pins
0.37 (9.5) Centre
L
N-VOUT
+VOUT
B
1.13
(28.72)
1.03 (26.2)
2.1 (53.34)
VR
LED
5.35 (136.0) 0.70 (17.9)
3.6
(91.44)
1.61
(41.0) -2X
2.44
(62.0)
AIRFLOW
A
AA
A
A
A
C
L
LOGIC CONNECTOR J3
DETAIL B
SCALE 2 : 1
PIN 1
PIN 9
PIN 2
PIN 10
J3 Logic Connector
(JST B10B-PHDSS)
Pin Function
1 + Sense
2 - Sense
3 AC OK/Power Fail
4 - Sense
5 Current Share
6 Current Share
7 + Inhibit
8 - Inhibit
9 +5 V Standby
10 5 V Standby Return
Notes
1. Peak power available for 10 seconds with 35% duty cycle.
Mechanical Details
End Fan
Output Voltage V1 Output Current V1 Standby Supply V2 Output Power Model Number
Continuous Peak
12 V 26.5 A 5 V / 0.2 A 318 W SHP350PS12
15 V 22.0 A 5 V / 0.2 A 330 W SHP350PS15
24 V 14.5 A 5 V / 0.2 A 348 W 417 W SHP350PS24
28 V 12.5 A 5 V / 0.2 A 350 W 420 W SHP350PS28
36 V 9.7 A 5 V / 0.2 A 350 W 420 W SHP350PS36
48 V 7.3 A 5 V / 0.2 A 350 W 420 W SHP350PS48
SHP650
Mechanical Details
Models and Ratings
Notes
1. For top fan version replace ‘-EF’ in model number with ‘-TF’, e.g.
SHP650PS12-TF
2. For U Channel version remove suffix.
3. U Channel models require a minimum of 5.5 m/s airflow from the system.
4. Not available for ‘-TF’ and ‘-EF’ models as used by integral fan.
Output Voltage V1 Output Current V1 Fan Supply V2(4) Standby Supply V3 Output Power(3) Model Number(1,2)
12 V 50.0 A 12 V / 0.5 A 5 V / 0.2 A 607 W SHP650PS12-EF
15 V 40.0 A 12 V / 0.5 A 5 V / 0.2 A 607 W SHP650PS15-EF
24 V 27.0 A 12 V / 0.5 A 5 V / 0.2 A 655 W SHP650PS24-EF
28 V 23.0 A 12 V / 0.5 A 5 V / 0.2 A 655 W SHP650PS28-EF
36 V 18.0 A 12 V / 0.5 A 5 V / 0.2 A 655 W SHP650PS36-EF
48 V 13.5 A 12 V / 0.5 A 5 V / 0.2 A 655 W SHP650PS48-EF
End Fan (See Longform Datasheet for UChannel Version)
1. Dimensions shown in inches (mm).
2. Weight: 2.8 lb (1.27 kg).
3. J3 Mating Plug: JST part no. PHR-2, contact: JST part no.
SPH-002T-P0.5S; J3 Mating Plug: JST part no. PHDR-10VS,
contact: 26-22AWG JST part no. SPHD-001T-P0.5
Notes
Vo+Vo-
Standard Terminal Block, M4 Screw, 6 Pins, 9.5 mm Center
torque 10.62 lbs-in (1.2 Nm)
Standard Terminal
Block, M3.5 Screw 3
Pins 9.5 mm Center
torque 10.62 lbs-in (1.2 Nm)
9.18 (233.2)
N
E
L
2.50 (63.5)
V1 Adjustment
Output On, LED
1.95
(49.5)
2.49
(63.3)
AIRFLOW
Pin 1
Pin 9
Pin 2
Pin 10
J3: Logic Connector
0.87
(22.2)
2.86 (72.6)
6.53 (165.8)
8.00 (203.2)
4.00
(101.6)
C
L
2 x M3 THD both side faces
0.15 (3.8) max screw penetration
max torque 4.0-5.0 lbs-in (0.45-0.57 Nm)
4 x M3 THD
0.15 (3.8) max screw penetration
max torque 4.0-5.0 lbs-in (0.45-0.57 Nm)
J3 Logic Connector
(JST B10B-PHDSS)
Pin Function
1 + Sense
2 - Sense
3 AC OK/Power Fail
4 - Sense
5 Current Share
6 Current Share
7 + Inhibit
8 - Inhibit
9 +5 V Standby (V3)
10 5 V Standby Return (V3)
ACDC
ACDC
SHP650
Mechanical Details
Top Fan (Suffix TF)
Standard Terminal Block, M4 Screw, 6 Pins, 9.5 mm Center
torque 10.62 lbs-in (1.2 Nm)
Standard Terminal Block, M3.5 Screw 3, Pins 9.5 mm Center
torque 10.62 lbs-in (1.2 Nm)
Vo+Vo-
N
E
8.00 (203.2)
L
2.58 (65.5)
2.50 (63.5)
1.95
(49.5)
0.87
(22.2)
6.53 (165.8)
2.86 (72.6)
4.00
(101.6)
Pin 1
pin 9
Pin 2
Pin 10
J3: Logic Connector
V1 Adjustment
Output On, LED
AIRFLOW
2 x M3 THD both side faces
0.15 (3.8) max screw penetration
max torque 4.0-5.0 lbs-in (0.45-0.57 Nm)
4 x M3 THD
0.15 (3.8) max screw penetration
max torque 4.0-5.0 lbs-in (0.45-0.57 Nm)
Signals
AC OK Collector
Pin 3
AC OK Emitter
Pin 2 (-sense)
POWER SUPPLY
Transistor On (<0.8 V):
AC NOT OK
Transistor Off (>4.5 V):
AC OK
INHIBIT HI INHIBIT LOW
J3 Logic Connector
330R
5 V Standby
Return Pin 10
5 V Standby
Pin 9
Max 12 V 20 mA Inhibit Hi
Pin 7
POWER SUPPLY
100 R
800 R
2-5 mA
Chassis J3 Logic Connector
Signal High: Power Supply OFF
Low or Floating: Power Supply ON
Signal High: Power Supply ON
Low or Floating: Power Supply OFF
Inhibit Lo
Pin 8
5 V Standby
Pin 9
5 V Standby
Return Pin 10
Inhibit Hi
Pin 7
POWER SUPPLY
100 R
Chassis J3 Logic Connector
Inhibit Lo
Pin 8
5 V Standby
Pin 9
5 V Standby
Return Pin 10
800 R
2-5 mA
Notes
J3 Logic Connector
(JST B10B-PHDSS)
Pin Function
1 + Sense
2 - Sense
3 AC OK/Power Fail
4 - Sense
5 Current Share
6 Current Share
7 + Inhibit
8 - Inhibit
9 +5 V Standby (V3)
10 5 V Standby Return (V3)
1. Dimensions shown in inches (mm).
2. Weight: 2.8 lb (1.27 kg).
3. J3 Mating plug: JST part no. PHDR-10VS, contact: 26-22
AWG JST part no. SPHD-001T-P0.5.
For U Channel and Thermal Considerations please see longform datasheet.
AC OK/Power Fail Remote On/Off (Inhibit)
21-Oct-13
ACDC
SHP1000
Mechanical Details
Models and Ratings
Output Voltage V1 Output Current V1 Standby Supply V2 Output Power Model Number
<180 VAC >180 VAC <180 VAC >180 VAC
12 V 83.0 A 5 V / 1.0 A 1000 W SHP1000PS12
15 V 67.0 A 5 V / 1.0 A 1010 W SHP1000PS15
24 V 42.0 A 50.0 A 5 V / 1.0 A 1013 W 1200 W SHP1000PS24
28 V 36.0 A 43.0 A 5 V / 1.0 A 1013 W 1200 W SHP1000PS28
36 V 28.0 A 34.0 A 5 V / 1.0 A 1013 W 1200 W SHP1000PS36
48 V 21.0 A 25.0 A 5 V / 1.0 A 1013 W 1200 W SHP1000PS48
1. Dimensions shown in inches (mm).
2. Weight: 4.6 lb (2.08 kg)
3. J3 Mating Plug: JST part no. PHDR-10VS,
contact: 26-22AWG JST part no. SPHD-001T-P0.5
Notes
C
L
4.50
(114.3)
1.20 (30.5)
Pin 2 Pin 1
Pin 10 Pin 9
Detail A J3: Logic Connector
9.41 (238.9)
BB
BB
BB
4 x M4-0.7 THD both side faces
0.15 (3.8) max screw penetration
max torque 10.62 lbs-in (1.2 Nm)
4 x M4-0.7 THD both side faces
0.15 (3.8) max screw penetration
max torque 10.62 lbs-in (1.2 Nm)
Airflow
1.33 (33.8)
6.70 (170.2)
VO+ VO-
L
N
A
9.48 (240.9)
5.90
(149.8)
2.91
(73.9)
1.20 (30.5)
1.47
(37.4)
9.55 (242.64)
2.40 (61.0)
V1 Adjustment
Output On, LED
Standard Terminal Block, M4 Screw
3 Pins 0.37 (9.5) center
Torque 10.62 lbs-in (1.2 Nm)
Standard Terminal Block, M6 Screw, 4 Pins 0.62 (16.0) center
Torque 26.0 lbs-in (2.94 Nm)
J3 Logic Connector
(JST B10B-PHDSS)
Pin Function
1 + Sense
2 - Sense
3 AC OK/Power Fail
4 - Sense
5 Current Share
6 Current Share
7 + Inhibit
8 - Inhibit
9 +5 V Standby
10 -5 V Standby
ACDC