Specification : TS-S00D022A Jun, 2000 Technical Specification for 2.5Gbps Fiber Optic Receiver Module SDT9308-R 155.52Mb/s 622.08Mb/s 0.1 ~ 2.7Gbps other ____________ Short Haul Intermediate Reach other ____________ Single 5.0 V Long Haul Long Reach Single 3.3 V other ____________ 1.3 m 1.55 m other ____________ Transmitter Receiver Transceiver ( 2R / 3R ) ( 2R / 3R ) Sumitomo Electric reserves the right to make changes in this specification without prior notice. #Safety Precaution Symbols This specification uses various picture symbols to prevent possible injury to operator or other persons or damage to properties for appropriate use of the product. The symbols and definitions are as shown below. Be sure to be familiar with these symbols before reading this specification. Warning Caution Wrong operation without following this instruction may lead to human death or serious injury. Wrong operation without following this instruction may lead to human injury or property damage. indicates prohibition of actions. Action details are explained thereafter. indicates compulsory actions or instructions. Action details are explained thereafter. (SDT9308-R) -1/7- Specification : TS-S00D022A Jun, 2000 1. General The features of SDT9308-R are listed below: * SDH STM-16 I-16, S-16.1 & S-16.2 / SONET OC-48 SR-1, IR-1 & IR-2 Compliant * Power Supply Voltage Single +5V * Low Power Supply Current 100mA (typ.) * Compact Package Size 58.4 X 26.8 X 8.5 mm * Differential PECL output * Signal Detect (FLAG) Function * Optical Input Power Monitor Function * Optical Connector Interface FC / SC connector 2. Block Diagram Vcca Pre-Amplifier RD RDb 2R-IC Comparater IC LPA OP-amplifier OIL Figure 1 Block Diagram 3. Package Dimension 0.6 max 2.54x11=27.9 4 18 +/0.5 0. 4 0.5 7 max 1.55 3.5 +/0.3 25.4 +/-0.2 35.6 +/-0.4 3.95 23.50 +/-4 8.9 max 58.20 +/-0.4 Pigtail Length : Please refer to Section 11 Figure 2 Package Dimension Caution Do not disassemble this product. Otherwise, failure, electrical shock, overheating or fire may occur. Handle the lead pins carefully. Use assisting tools or prospective aids as required. A lead pin may injure skin or human body (SDT9308-R) -2/7- Specification : TS-S00D022A Jun, 2000 4. Pin Assignment No. 1 2 3 4 5 6 7 8 9 10 11 12 Symbol NIC NUC LPA GND NIC NIC GND Vccd GND RD RDb GND Function No Internal Connection No User Connection Loss of Power Alarm Ground No Internal Connection No Internal Connection Ground Positive power supply ( Digital ) Ground True data output False data output Ground No. 24 23 22 21 20 19 18 17 16 15 14 13 Symbol NUC OIL Vcca NUC GND GND NIC GND GND GND GND NIC Function No User Connection Optical Input Level Positive power supply ( Analogue ) No User Connection Ground Ground No Internal Connection Ground Ground Ground Ground Not Internally Connected 5. Absolute Maximum Ratings Parameter Storage Case Temperature Operating Case Temperature Supply Voltage Maximum Input Power Lead Soldering (Temperature) (Time) Symbol Ts Tc Vccd, Vcca Pmax min. -40 -5 0.0 Max 85 75 6.0 3 260 10 Unit C C V dBm C sec. Note 1 2 3 Note 1. No condensation allowed. 2. GND=0.0V 3. Measured on lead pin at 2mm (0.079in.) off the package bottom Warning Use the product with the rated voltage described in the specification. If the voltage exceeds the maximum rating, overheating or fire may occur. Caution Do not store the product in the area where temperature exceeds the maximum rating, where there is too much moisture or dampness, where there is acid gas or corrosive gas, or other extreme conditions. Otherwise, failure, overheating or fire may occur. (SDT9308-R) -3/7- Specification : TS-S00D022A Jun, 2000 6. Electrical Interface ( Unless otherwise specified, Vcca, Vccd = 4.75 to 5.25 V, @2488.32Mbps, PRBS2^23-1,50% duty and all operating temperature shall apply. ) Parameter Supply Voltage Supply Current (Vcca and Vccd) Output Voltage Level ( RD, RDb ) Output Voltage ( LPA ) Symbol Vcca, Vccd Idrx Voh Vol Voflgh Voflgl Trd/Tfd Voil Voil High Low High Low Output Signal Rise / Fall Time (RD, RDb, 20% - 80%) Input Power Monitor Voltage @-18dBm @ 0dBm Min. 4.75 Typ. 5.00 100 Max. 5.25 150 Vcc-0.65 Vcc-1.3 Vcc 0.40 180 Vcc-1.1 Vcc-1.8 Vcc-0.4 0 130 0.065 4.0 Unit V mA V V V V ps V V Note 1, 2 3, 4 3, 4 3 3 1. 2488.32Mbps, PRBS 2^23-1 2. Output current is not included. 3. Vccd, Vcca = 5.0V, Tc = 25C 4. Rl = 50 to Vcc-2V, Single end out. Tfld Optical Signal Optical Input High Low LPA "H" "L" RD and RDb Data Output RD RDb "H" "L" "L" "H" Figure 3 Output Timing Chart Vcca @V cc =5.0V , Tc= 25 degC Monito r V o ltage (mV ) 10 00 Vcc PD Monitor Voltage (Pin 23) Preamplifier Resistor(5.1kohm) 1 00 10 1 -30 - 25 -20 -15 - 10 -5 O pt ical In p ut P ow er (dB m ) Figure 4 Input Power Monitoring Circuit Figure 5 Relation Between Optical Input Power 7. Optical Interface ( Unless otherwise specified, Vcca, Vccd = 4.75 to 5.25 V, @2488.32Mbps, PRBS2^23-1,50% duty and all operating temperature shall apply. ) Parameter Bit Rate Range Center Wavelength Range Symbol Minimum Sensitivity Overload LPA Deassert Level LPA Assert Level Hysteresis LPA Deassertion Time Optical Reflectance c Min. 0.1 1260 1430 Pmin Pmax Pa Pd Hys Tlpa Or 0 -40.0 -40.0 0.5 2.3 -22.0 1. BER = 10^-10 2. Refer to Figure 4 (SDT9308-R) Typ. -4/7- -23.0 -25.0 2.0 Max. 2.7 1360 1580 -18.0 -18.0 -18.0 6.0 100 -27 Unit Gbps nm Note dBm dBm dBm dBm dB s dB 1 1 2 0 Specification : TS-S00D022A Jun, 2000 8. Recommended User Interface L1 Vcc(+5V) C3 C3 1 NC R1 NC 24 2 NC Vmon 23 3 LOS VccA 22 4 GND NC 21 C3 5 NC GND 20 R1 6 NC GND 19 7 GND GND 18 8 VccD GND 17 9 GND GND 16 RD 10 RD GND 15 RDb 11 RDb GND 14 12 GND NUC 13 LOS C1 C2 Vmon C1 C2 L1 C3 L1=100 H : SLF7045T-101MR50(TDK) C1=0.022 F : Ceramic Chip Condensor. ( >25V ) C2=1000pF : Ceramic Chip Condensor. ( >25V ) C3=10 F : EEFCD113100R ( Panasonic ) R1=5 1. Power supply filter should be located as close as possible to the lead pins of module. 2. The impedance of transmission line ( RD & RDb ) should be 50ohm. 3. Since the transmission line ( RD & RDb ) are open emitters, termination resistors ( 1/8W ) are necessary. Shown below is the recommendation. Transmission Line(50 ) Transmission Line(50 ) Vcc 82 50 130 Vee Vcc-2V Figure 6 Recommended User Interface 9. Fiber Pigtail Specification Parameter Core Diameter Cladding Diameter Outer Diameter Optical Cord Tensile Beak Strength Bend Radius Min. Typ. 9.5 125 0.9 Max. 9.8 30 Unit m m mm N mm Note Caution Do not give undue force or impact to the optical fiber pigtail. A broken optical fiber may injure skin or human body, or a strong laser beam may cause eye injury. Operate the equipment carefully. Use assisting tools or prospective aids as required. (SDT9308-R) -5/7- Specification : TS-S00D022A Jun, 2000 10. Reliability Test (Plan) Bellcore TA-NWT-000983 Issue 2, December 1993 Heading Test Mechanical Mechanical Integrity Shock Vibration Reference Sampling LTPD SS C SEI Results SS F/C MIL-STD-883 Condition B Method 2002 5 times/axis 500G, 1.0 ms 20% 11 0 11 0 1,500G, 0.5ms Condition A 20% 20% 11 11 0 0 --11 --0 20% 11 0 11 0 (steam aging not required) 20% 11 0 11 0 1 Kg; 3 times;5sec. 20% 11 0 --- --- 20% 11 0 --- --- (R)-453 2 Kg; 3 times; 5sec. +85C; rated power Section 5.18 >5,000hrs. --- 25 --- 25 0 >10,000hrs. --- 10 --- --- --- MIL-STD-883 Method 2007 Thermal Shock MIL-STD-883 Solderability Condition Method 1011 MIL-STD-883 20 G 20-2,000 Hz 4 min/cycle; 4 cycles/axis T=100C Method 2003 Fiber Pull Endurance Accel. Aging (High Temp.) High Temp. Storage ---------- max. storage T (T=85C) >2,000 20% 11 0 --- --- Low Temp. Storage Temperature ---------- min. storage T (T=-40C) >2,000 - 40C to +85C 20% 11 0 11 0 400 times pass/fail 500 times for info. 20% --- 11 11 0 --- ----- ----- 500 times pass/fail 1000 times for info. 20% --- 11 11 0 --- 11 11 0 0 Damp Heat MIL-STD-202 M103 40C , 95%, 56days 20% (if using epoxy) or IEC 68-2-3 or 85C /85%RH 2,000hrs. 20% 11 11 0 0 11 --- 0 --- Cyclic Moisture Section 5.23 Resistance ---------- 20% 11 0 11 0 Internal Moisture < 5,000 ppm water vapor 20% 11 0 11 0 ------- ---6 ----- ---6 OK 0 Section 5.20 Cycling Special Tests MIL-STD-883 Method 1018 Flammability TR357:Sec. 4.4.2.5 ----------ESD Threshold Section 5.22 ----------- 11. Ordering Information Connector SC Connector FC / PC Connector FC / PC Connector (SDT9308-R) Pigtail Length : mm 600 +/- 50 600 +/- 50 990 +/- 100 -6/7- Tc = 0 ~ 70C SDT9308-RC-QN SDT9308-RD-QN SDT9308-RD-YN Specification : TS-S00D022A Jun, 2000 12. Other Precaution Under such a strong vibration environment as in automobile, the performance and reliability are not guaranteed. The governmental approval is required to export this product to other countries. To dispose of these components, the appropriate procedure should be taken to prevent illegal exportation. This module must be handled, used and disposed of according to your company's safe working practice. Warning Be sure to carry out correct soldering for connection to peripheral circuits in order to prevent contact failure or short-circuit. Otherwise, a strong laser beam may cause eye injury, overheating or fire. Do not put this product or components of this product into your mouth. This product contaions material harmful to health. Caution Be sure to turn power off when you touch this product connected to the printed circuit boards. Otherwise, electric shock may occur. Dispose this product or equipment including this product properly as an industrial waste according to the regulations. 13. For More Information U.S.A. Sumitomo Electric Lightwave Corp, 78 Alexander Drive, Research Triangle Park, NC 27709 Tel. +1-919-541-8100 / Fax. +1-919-541-8376 E-mail: info@sumitomoelectric.com http://www.sumitomoelectric.com/products/eop Europe Sumitomo Electric Europe Ltd., 220, Centennial Park, Elstree, Herts, WD6 3SL, United Kingdom Tel. +44-208-953-8681 Fax. +44-208-207-5950 Japan Sumitomo Electric Industries, Ltd. ( International Business Division ), 3-12, Moto-Akasaka 1-chome Minato-ku Tokyo 107-8468 Tel. +81-3-3423-5771 / Fax. +81-3-3423-5099 E-mail: product-info@ppd.sei.co.jp http://www.sei.co.jp/Electro-optic/index.html (SDT9308-R) -7/7-