SDT9308-RC-QN - ExceLight Communications

(SDT9308-R)

Specification : TS-S00D022A

Jun, 2000

- 1 / 7 -

155.52Mb/s 622.08Mb/s other ___________

Transmitter Receiver Transceiver

Short Haul Long Haul

Intermediate Reach Long Reach

Single 5.0 V Single 3.3 V other ___________

1.3 µm 1.55 µm other ___________

( 2R / 3R ) ( 2R / 3R )

other ___________

Technical Specification

for

2.5Gbps Fiber Optic Receiver Module

SDT9308-R

Sumitomo Electric reserves the right to make changes in this specification without prior notice.

0.1 ~ 2.7Gbps

#Safety Precaution Symbols This specification uses various picture symbols to prevent possible injury to operator or

other persons or damage to properties for appropriate use of the product. The symbols and definitions are as shown below. Be sure to be

familiar with these symbols before reading this specification.

Warning Wrong operation without following this instruction may lead to human death or serious injury.

Caution Wrong operation without following this instruction may lead to human injury or property damage.

indicates prohibition of actions. Action details are explained thereafter.

indicates compulsory actions or instructions. Action details are explained thereafter.

(SDT9308-R)

Specification : TS-S00D022A

Jun, 2000

- 2 / 7 -

1. General

The features of SDT9308-R are listed below:

* SDH STM-16 I-16, S-16.1 & S-16.2 / SONET OC-48 SR-1, IR-1 & IR-2 Compliant

* Power Supply Voltage Single +5V

* Low Power Supply Current 100mA (typ.)

* Compact Package Size 58.4 X 26.8 X 8.5 mm

* Differential PECL output

* Signal Detect (FLAG) Function

* Optical Input Power Monitor Function

* Optical Connector Interface FC / SC connector

Caution

Do not disassemble this product. Otherwise, failure, electrical shock, overheating or fire may occur.

Handle the lead pins carefully. Use assisting tools or prospective aids as required. A lead pin may injure skin or human body

Figure 2 Package Dimension

23.50 +/-4

58.20 +/-0.4

8.9 max

3.95

3.5 +/-

0.3

0.5

25.4 +/-0.2

35.6 +/-0.4

0.6 max

1.55

2.54x11=27.9

418 +/-

0.5

7 max

Pigtail Length : Please refer to Section 11

2. Block Diagram

3. Package Dimension

RDb

Pre-Amplifier

Vcca

2R-IC

LPA

Comparater IC

OP-amplifier OIL

Figure 1 Block Diagram

(SDT9308-R)

Specification : TS-S00D022A

Jun, 2000

- 3 / 7 -

5. Absolute Maximum Ratings

4. Pin Assignment

Warning

Use the product with the rated voltage described in the specification. If the voltage exceeds the maximum rating, overheating or

fire may occur.

Caution

Do not store the product in the area where temperature exceeds the maximum rating, where there is too much moisture or

dampness, where there is acid gas or corrosive gas, or other extreme conditions. Otherwise, failure, overheating or fire may

occur.

No. S

mbol Function No. S

mbol Function

1 NIC No Internal Connection 2 4 NUC No Us er Co nnection

2 NUC No User Connection 23 OIL Optical Input Level

3 LPA Lo s s of P ower Ala r m 22 Vc c a Posi tiv e pow e r s upp l

( Analo

ue )

4 GND Ground 2 1 NUC No Us er Co nnection

5 N IC No Int erna l Co nn ec tio n 20 GN D Grou nd

6 N IC No Int erna l Co nn ec tio n 19 GN D Grou nd

7 G ND G r ou nd 18 N IC N o Inter na l Co nn ec t io n

8 Vccd Posit ive power suppl

( Di

it al ) 17 G ND G r ou nd

9 GND Ground 16 GND Ground

10 RD True data ou tput 15 GND Gr ound

11 RDb False data output 14 GND Ground

12 GND Ground 13 NIC Not Internall

C onn ec te d

Parameter Symbol min. Max Unit Note

Storage Case Temperature Ts -40 85 °C 1

Oper at ing Cas e T emperat ure Tc -5 75 °C

Suppl y Voltage Vccd, Vcca 0.0 6.0 V 2

Maximum Input Power Pmax 3 dBm

Lead Solderi ng (Temperature) 260 °C 3

(Time) 10 sec.

Note 1. No condensation allowed. 2. GND=0.0V

3. Measured on lead pin at 2m m (0.079in.) off the package bottom

(SDT9308-R)

Specification : TS-S00D022A

Jun, 2000

- 4 / 7 -

6. Electrical Interface

( Unless otherwise specified, Vcca, Vccd = 4.75 to 5.25 V, @2488.32Mbps, PRBS2^23-1,50% duty

and all operating temperature shall apply. )

7. Optical Interface

( Unless otherwise specified, Vcca, Vccd = 4.75 to 5.25 V, @2488.32Mbps, PRBS2^23-1,50% duty

and all operating temperature shall apply. )

Opti cal Input RD RDb

"H" "H" "L"

"L" "L" "H"

Data Ou tpu t

LPA

RD and RDb

Optical Signal

Tfld

Figure 3 Output Timing Chart

Low High

Parameter S

mbol Min. T

p. Max. Unit Note

Suppl

Vo lta

e Vcca, Vccd 4. 75 5. 00 5. 25 V

Suppl

Current

(

Vcca and Vccd

)

Idr x 100 150 m A 1, 2

Output Volta

e Level Hi

h Voh Vcc-1. 1 Vcc-0.65 V 3, 4

(

RD , R Db

)

Low Vol Vcc-1. 8 V cc-1.3 V 3, 4

Output Volta

(

LPA

)

hVofl

h Vcc-0.4 Vcc V 3

Low Vofl

l 0 0.40 V 3

Output Si

nal Rise / Fall Time

(

RD, RDb, 20 % - 80 %

)

Trd/Tfd 130 180 ps

In put Pow er Monitor Volta

e @-18dBm Voil 0.065 V

@ 0dBm Voil 4.0 V

1. 2488.32Mbps, PRBS 2^23-1 2. Output current is not included. 3. Vccd, V cca = 5.0V, Tc = 25°C

4. Rl = 50Ω to V cc-2V, Single end out.

Vcc

Preamplifier

Resistor(5.1kohm)

Monitor Voltage

(Pin 23)

Figure 4 Input Power Monitoring Circuit

Vcca

100

1000

-30 -25 -20 -15 -10 -5 0

Monito r Voltage (m V)

O ptical In put Power (dBm )

@V cc =5.0V , Tc= 25 degC

Figure 5 Relation Between Optical Input Power

Parameter Symbol Min. Typ. Max. Unit Note

Bit Rate Range 0.1 2.7 Gbps

Center Wavelengt h R ange λc 1260 1360 nm

1430 1580

Mini mum Sensitivi ty Pm in -22.0 -18.0 dBm 1

Overload Pmax 0 dBm 1

LPA Deas sert Level Pa -40.0 -23.0 -18.0 dBm

LPA Asser t Level Pd - 40.0 -25.0 -18.0 dBm

Hysteresis Hys 0.5 2.0 6.0 dB

LPA Deas serti on Ti me T lpa 2.3 100 µs2

Opti cal Reflectance Or -27 dB

1. BER = 1 0^-10 2. Refer to Figure 4

(SDT9308-R)

Specification : TS-S00D022A

Jun, 2000

- 5 / 7 -

8. Recommended User Interface

9. Fiber Pigtail Specification

Caution

Do not give undue force or impact to the optical fiber pigtail. A broken optical fiber may injure skin or human body, or a strong

laser beam may cause eye injury. Operate the equipment carefully. Use assisting tools or prospective aids as required.

Parameter Min. Typ. Max. Unit Note

Co re Di ameter 9. 5 µm

Cladding Diameter 125 µm

Outer Diameter 0.9 mm

Opti cal Cord Tensil e B eak Strengt h 9.8 N

Bend R adi us 30 mm

RDb

1 NC

2 NC

3 LOS

4 GND

5 NC

6 NC

7 GND

8 VccD

9 GND

10 RD

11 RDb

12 GND NUC 13

GND 1 4

GND 15

GND 1 6

GND 1 7

GND 1 8

GND 19

GND 2 0

NC 21

VccA 2 2

Vmon 23

NC 24

C1=0.022

F : Ceramic Chip Condensor. ( >25V )

C2=1000pF : Ceramic Chip Condensor. ( >25V )

C3=10

F : EEFCD113100R ( Panasonic )

R1=5

Ω

Vmon

Vcc(+5V)

L1=100

H : SLF7045T-101MR50(TDK)

Vcc-2V

Transmission

Line(50

Ω

)

Ω

Vee

Vcc

130

Ω

LOS

1. Power supply filter should be located as close as possible to the lead pins of module.

2. The impedance of transmission line ( RD & RDb ) should be 50ohm.

3. Since the transmission line ( RD & RDb ) are open emitters, termination resistors

( 1/8W ) are necessary. Shown below is the recommendation.

Transmission

Line(50

Ω

)

Figure 6 Recommended User Interface

(SDT9308-R)

Specification : TS-S00D022A

Jun, 2000

- 6 / 7 -

10. Reliability Test (Plan)

Bellcor e TA-N WT-0 00983 Issue 2, December 1993

Heading Test Reference Condition Sampling SEI Resul ts

LTPD SS C SS F/C

Mechanica

Mech anical M IL-STD-883 Co ndition B

Integrit y Shock Met hod 2002 5 t imes/axis

500G , 1.0 ms 20% 11 0 11 0

1,500G, 0.5ms 20% 11 0 --- ---

Vibration M IL-STD-883 Co ndition A 20% 11 0 11 0

Method 2007 20 G

20-2,000 Hz

4 min /cycle; 4 cycles/axis

Therm al Shock MIL-STD -883 ∆T=100°C 20% 11 0 11 0

Method 1011

Solderabi lit y MIL-STD-883 (steam aging not required) 20% 11 0 11 0

Method 2003

Fi ber Pul l 1 Kg; 3 times;5sec. 20% 11 0 - -- ---

2 Kg; 3 ti mes; 5sec. 20% 11 0 --- ---

Endurance Accel. Aging (R)-453 +85C; rat ed power

(High T emp.) Section 5. 18 >5,000hrs. --- 25 --- 25 0

>10,000hrs. --- 10 --- --- ---

H igh Temp . -- -------- max. storage T ( T= 8 5 °C ) 20 % 1 1 0 --- ---

Storage >2,000

Lo w T e mp. ------ ---- mi n . sto rage T (T= -4 0°C) 20% 11 0 11 0

Storage >2,000

Temper ature Section 5.20 - 40°C to +85 °C

Cyc ling 400 times pass/fail 20% 11 0 --- ---

500 t im es for inf o. --- 11 --- -- - -- -

500 times p as s/fai l 20% 11 0 11 0

1000 times for i nfo. --- 11 --- 11 0

Damp Heat MIL-STD-202 M103 40°C , 95%, 56day s 20% 11 0 11 0

(if using epoxy) or IEC 68-2- 3 or 85°C /85%RH 2, 000hrs. 20% 11 0 --- ---

C y cli c Mo i s t ur e S e ctio n 5 .23 -- -------- 20 % 11 0 1 1 0

Resist anc e

Special Int ernal MI L-STD-883 < 5,000 ppm 20% 11 0 11 0

Tes ts Moistur e Method 1018 w at er vapor

Flam mabili ty TR357: Sec . 4.4. 2.5 -- --------- ---- ---- --- ---- OK

E S D T hr e s h old Se ctio n 5 .22 -- --------- ---- 6 --- 6 0

11. Ordering Information

Connector Pigtail Lengt h : mm Tc = 0 ~ 70°C

SC Connector 600 + /- 50 SDT9308-RC-Q N

FC / PC Connector 600 + /- 50 SDT9308-RD-Q N

FC / PC Connector 990 + /- 100 S DT9308-RD-YN

(SDT9308-R)

Specification : TS-S00D022A

Jun, 2000

- 7 / 7 -

12. Other Precaution

Under such a strong vibration environment as in automobile, the performance and reliability are not guaranteed.

The governmental approval is required to export this product to other countries. To dispose of these compo-

nents, the appropriate procedure should be taken to prevent illegal exportation.

This module must be handled, used and disposed of according to your company's safe working practice.

13. For More Information

U.S.A.

Sumitomo Electric Lightwave Corp, 78 Alexander Drive, Research Triangle Park, NC 27709

Tel. +1-919-541-8100 / Fax. +1-919-541-8376

E-mail: info@sumitomoelectric.com

http://www.sumitomoelectric.com/products/eop

Europe

Sumitomo Electric Europe Ltd., 220, Centennial Park, Elstree, Herts, WD6 3SL, United Kingdom

Tel. +44-208-953-8681

Fax. +44-208-207-5950

Japan

Sumitomo Electric Industries, Ltd. ( International Business Division ), 3-12, Moto-Akasaka 1-chome

Minato-ku Tokyo 107-8468

Tel. +81-3-3423-5771 / Fax. +81-3-3423-5099

E-mail: product-info@ppd.sei.co.jp

http://www.sei.co.jp/Electro-optic/index.html

Caution

Be sure to turn power off when you touch this product connected to the printed circuit boards. Otherwise, electric shock may occur.

Dispose this product or equipment including this product properly as an industrial waste according to the regulations.

Warning

Be sure to carry out correct soldering for connection to peripheral circuits in order to prevent contact failure or short-circuit.

Otherwise, a strong laser beam may cause eye injury, overheating or fire.

Do not put this product or components of this product into your mouth. This product contaions material harmful to health.