AVAILABLE
Functional Diagrams
Pin Configurations appear at end of data sheet.
Functional Diagrams continued at end of data sheet.
UCSP is a trademark of Maxim Integrated Products, Inc.
For pricing, delivery, and ordering information, please contact Maxim Direct
at 1-888-629-4642, or visit Maxim’s website at www.maximintegrated.com.
General Description
The MAX220–MAX249 family of line drivers/receivers is
intended for all EIA/TIA-232E and V.28/V.24 communica-
tions interfaces, particularly applications where ±12V is
not available.
These parts are especially useful in battery-powered sys-
tems, since their low-power shutdown mode reduces
power dissipation to less than 5µW. The MAX225,
MAX233, MAX235, and MAX245/MAX246/MAX247 use
no external components and are recommended for appli-
cations where printed circuit board space is critical.
________________________Applications
Portable Computers
Low-Power Modems
Interface Translation
Battery-Powered RS-232 Systems
Multidrop RS-232 Networks
Next-Generation Device Features
♦♦For Low-Voltage, Integrated ESD Applications
MAX3222E/MAX3232E/MAX3237E/MAX3241E/
MAX3246E: +3.0V to +5.5V, Low-Power, Up to
1Mbps, True RS-232 Transceivers Using Four
0.1µF External Capacitors (MAX3246E Available
in a UCSP™ Package)
♦♦For Low-Cost Applications
MAX221E: ±15kV ESD-Protected, +5V, 1µA,
Single RS-232 Transceiver with AutoShutdown™
+5V-Powered, Multichannel RS-232
Drivers/Receivers
Selection Table
19-4323; Rev 16; 7/10
PART
MAX220CPE+
MAX220CSE+
MAX220CWE+ 0°C to +70°C
0°C to +70°C
0°C to +70°C
TEMP RANGE PIN-PACKAGE
16 Plastic DIP
16 Narrow SO
16 Wide SO
MAX220C/D 0°C to +70°C Dice*
MAX220EPE+
MAX220ESE+
MAX220EWE+ -40°C to +85°C
-40°C to +85°C
-40°C to +85°C 16 Plastic DIP
16 Narrow SO
16 Wide SO
MAX220EJE -40°C to +85°C 16 CERDIP
MAX220MJE -55°C to +125°C 16 CERDIP
Power No. of Nominal SHDN Rx
Part Supply RS-232 No. of Cap. Value & Three- Active in Data Rate
Number (V) Drivers/Rx Ext. Caps (µF) State SHDN (kbps) Features
MAX220 +5 2/2 4 0.047/0.33 No — 120 Ultra-low-power, industry-standard pinout
MAX222 +5 2/2 4 0.1 Yes — 200 Low-power shutdown
MAX223 (MAX213) +5 4/5 4 1.0 (0.1) Yes ✔120 MAX241 and receivers active in shutdown
MAX225 +5 5/5 0 — Yes ✔120 Available in SO
MAX230 (MAX200) +5 5/0 4 1.0 (0.1) Yes — 120 5 drivers with shutdown
MAX231 (MAX201) +5 and 2/2 2 1.0 (0.1) No — 120 Standard +5/+12V or battery supplies;
+7.5 to +13.2 same functions as MAX232
MAX232 (MAX202) +5 2/2 4 1.0 (0.1) No — 120 (64) Industry standard
MAX232A +5 2/2 4 0.1 No — 200 Higher slew rate, small caps
MAX233 (MAX203) +5 2/2 0 — No — 120 No external caps
MAX233A +5 2/2 0 — No — 200 No external caps, high slew rate
MAX234 (MAX204) +5 4/0 4 1.0 (0.1) No — 120 Replaces 1488
MAX235 (MAX205) +5 5/5 0 — Yes — 120 No external caps
MAX236 (MAX206) +5 4/3 4 1.0 (0.1) Yes — 120 Shutdown, three state
MAX237 (MAX207) +5 5/3 4 1.0 (0.1) No — 120 Complements IBM PC serial port
MAX238 (MAX208) +5 4/4 4 1.0 (0.1) No — 120 Replaces 1488 and 1489
MAX239 (MAX209) +5 and 3/5 2 1.0 (0.1) No — 120 Standard +5/+12V or battery supplies;
+7.5 to +13.2 single-package solution for IBM PC serial port
MAX240 +5 5/5 4 1.0 Yes — 120 DIP or flatpack package
MAX241 (MAX211) +5 4/5 4 1.0 (0.1) Yes — 120 Complete IBM PC serial port
MAX242 +5 2/2 4 0.1 Yes ✔200 Separate shutdown and enable
MAX243 +5 2/2 4 0.1 No — 200 Open-line detection simplifies cabling
MAX244 +5 8/10 4 1.0 No — 120 High slew rate
MAX245 +5 8/10 0 — Yes ✔120 High slew rate, int. caps, two shutdown modes
MAX246 +5 8/10 0 — Yes ✔120 High slew rate, int. caps, three shutdown modes
MAX247 +5 8/9 0 — Yes ✔120 High slew rate, int. caps, nine operating modes
MAX248 +5 8/8 4 1.0 Yes ✔120 High slew rate, selective half-chip enables
MAX249 +5 6/10 4 1.0 Yes ✔120 Available in quad flatpack package
Ordering Information
+
Denotes a lead(Pb)-free/RoHS-compliant package.
*
Contact factory for dice specifications.
Ordering Information continued at end of data sheet.
AutoShutdown and UCSP are trademarks of Maxim Integrated
Products, Inc.
MAX220–MAX249
MAX220–MAX249
Selection Table
+5V-Powered, Multichannel RS-232
Drivers/Receivers
ABSOLUTE MAXIMUM RATINGS—MAX220/222/232A/233A/242/243
ELECTRICAL CHARACTERISTICS—MAX220/222/232A/233A/242/243
(VCC = +5V ±10%, C1–C4 = 0.1µF‚ MAX220, C1 = 0.047µF, C2–C4 = 0.33µF, TA= TMIN to TMAX‚ unless otherwise noted.) (Note 3)
Note 1: For the MAX220, V+ and V- can have a maximum magnitude of 7V, but their absolute difference cannot exceed 13V.
Note 2: Input voltage measured with TOUT in high-impedance state, VSHDN or VCC = 0V.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
(Voltages referenced to GND.)
VCC ...........................................................................-0.3V to +6V
V+ (Note 1) ..................................................(VCC - 0.3V) to +14V
V- (Note 1) ..............................................................+0.3V to -14V
Input Voltages
TIN .............................................................-0.3V to (VCC - 0.3V)
RIN (Except MAX220)........................................................±30V
RIN (MAX220) ....................................................................±25V
TOUT (Except MAX220) (Note 2) ......................................±15V
TOUT (MAX220)..............................................................±13.2V
Output Voltages
TOUT..................................................................................±15V
ROUT........................................................-0.3V to (VCC + 0.3V)
Driver/Receiver Output Short Circuited to GND.........Continuous
Continuous Power Dissipation (TA= +70°C)
16-Pin Plastic DIP (derate 10.53mW/°C above +70°C)..842mW
18-Pin Plastic DIP (derate 11.11mW/°C above +70°C)..889mW
20-Pin Plastic DIP (derate 8.00mW/°C above +70°C) ..440mW
16-Pin Narrow SO (derate 8.70mW/°C above +70°C) ...696mW
16-Pin Wide SO (derate 9.52mW/°C above +70°C)......762mW
18-Pin Wide SO (derate 9.52mW/°C above +70°C)......762mW
20-Pin Wide SO (derate 10.00mW/°C above +70°C)....800mW
20-Pin SSOP (derate 8.00mW/°C above +70°C) ..........640mW
16-Pin CERDIP (derate 10.00mW/°C above +70°C).....800mW
18-Pin CERDIP (derate 10.53mW/°C above +70°C).....842mW
Operating Temperature Ranges
MAX2_ _AC_ _, MAX2_ _C_ _.............................0°C to +70°C
MAX2_ _AE_ _, MAX2_ _E_ _ ..........................-40°C to +85°C
MAX2_ _AM_ _, MAX2_ _M_ _.......................-55°C to +125°C
Storage Temperature Range .............................-65°C to +160°C
Lead Temperature (soldering, 10s) .................................+300°C
Soldering Temperature (reflow)
20 PDIP (P20M+1) .......................................................+225°C
All other lead(Pb)-free packages.................................+260°C
All other packages containing lead(Pb) ......................+240°C
PARAMETER CONDITIONS MIN TYP MAX UNITS
RS-232 TRANSMITTERS
Output Voltage Swing All transmitter outputs loaded with 3k to GND ±5 ±8 V
Input Logic-Low Voltage 1.4 0.8 V
All devices except MAX220 2 1.4
Input Logic-High Voltage MAX220: VCC = +5.0V 2.4 V
All except MAX220, normal operation 5 40
Logic Pullup/lnput Current VSHDN = 0V, MAX222/MAX242, shutdown,
MAX220 ±0.01 ±1 μA
VCC = +5.5V, VSHDN = 0V, VOUT = ±15V,
MAX222/MAX242 ±0.01 ±10
VOUT = ±15V ±0.01 ±10
Output Leakage Current
VCC = VSHDN = 0V MAX220, VOUT = ±12V ±25
μA
Data Rate 200 116 kbps
Transmitter Output Resistance VCC = V+ = V- = 0V, VOUT = ±2V 300 10M
VOUT = 0V ±7 ±22
Output Short-Circuit Current VOUT = 0V MAX220 ±60 mA
RS-232 RECEIVERS
±30
RS-232 Input Voltage Operating Range MAX220 ±25 V
All except MAX243 R2IN 0.8 1.3
RS-232 Input Threshold Low VCC = +5V MAX243 R2IN (Note 4) -3 V
All except MAX243 R2IN 1.8 2.4
RS-232 Input Threshold High VCC = +5V MAX243 R2IN (Note 4) -0.5 -0.1 V
2
Maxim Integrated
MAX220–MAX249
MAX220–MAX249
+5V-Powered, Multichannel RS-232
Drivers/Receivers
ELECTRICAL CHARACTERISTICS—MAX220/222/232A/233A/242/243 (continued)
(VCC = +5V ±10%, C1–C4 = 0.1µF‚ MAX220, C1 = 0.047µF, C2–C4 = 0.33µF, TA= TMIN to TMAX‚ unless otherwise noted.) (Note 3)
PARAMETER CONDITIONS MIN TYP MAX UNITS
All except MAX220/MAX243, VCC = +5V, no
hysteresis in shutdown 0.2 0.5 1.0
MAX220 0.3
RS-232 Input Hysteresis
MAX243 1
V
3 5 7
RS-232 Input Resistance TA = +25°C (MAX220) 3 5 7 k
IOUT = 3.2mA 0.2 0.4
TTL/CMOS Output Voltage Low IOUT = 1.6mA (MAX220) 0.4 V
TTL/CMOS Output Voltage High IOUT = -1.0mA 3.5 VCC - 0.2 V
Sourcing VOUT = VGND -2 -10
TTL/CMOS Output Short-Circuit Current Sinking VOUT = VCC 10 30 mA
TTL/CMOS Output Leakage Current VSHDN = VCC or VEN = VCC (VSHDN = 0V for
MAX222), 0V VOUT VCC ±0.05 ±10 μA
EN Input Threshold Low MAX242 1.4 0.8 V
EN Input Threshold High MAX242 2.0 1.4 V
Supply Voltage Range 4.5 5.5 V
MAX220 0.5 2
No load MAX222/MAX232A/MAX233A/
MAX242/MAX243 4 10
MAX220 12
VCC Supply Current (VSHDN = VCC),
Figures 5, 6, 11, 19
3k load
both inputs MAX222/MAX232A/MAX233A/
MAX242/MAX243 15
mA
TA = +25°C 0.1 10
TA = 0°C to +70°C 2 50
TA = -40°C to +85°C 2 50
Shutdown Supply Current MAX222/
MAX242
TA = -55°C to +125°C 35 100
μA
SHDN Input Leakage Current MAX222/MAX242 ±1 μA
SHDN Threshold Low MAX222/MAX242 1.4 0.8 V
SHDN Threshold High MAX222/MAX242 2.0 1.4 V
MAX222/MAX232A/
MAX233/MAX242/MAX243 6 12 30
Transition Slew Rate
CL = 50pF to 2500pF,
RL = 3k to 7k,
VCC = +5V, TA =
+25°C, measured
from +3V to -3V or
-3V to +3V
MAX220 1.5 3 30.0
V/μs
MAX222/MAX232A/
MAX233/MAX242/MAX243 1.3 3.5
tPHLT, Figure 1
MAX220 4 10
MAX222/MAX232A/
MAX233/MAX242/MAX243 1.5 3.5
Transmitter Propagation Delay TLL to
RS-232 (Normal Operation)
tPLHT, Figure 1
MAX220 5 10
μs
Maxim Integrated
3
MAX220–MAX249
MAX220–MAX249
+5V-Powered, Multichannel RS-232
Drivers/Receivers
__________________________________________Typical Operating Characteristics
MAX220/MAX222/MAX232A/MAX233A/MAX242/MAX243
10
8
-10
0 5 15 25
OUTPUT VOLTAGE vs. LOAD CURRENT
-4
-6
-8
-2
6
4
2
MAX220-01
LOAD CURRENT (mA)
OUTPUT VOLTAGE (V)
10
0
20
0.1μF
EITHER V+ OR V- LOADED
VCC = +5V
NO LOAD ON
TRANSMITTER OUTPUTS
(EXCEPT MAX220, MAX233A)
V- LOADED, NO LOAD ON V+
V+ LOADED, NO LOAD ON V-
1μF
1μF
0.1μF
11
10
4
010 40 60
AVAILABLE OUTPUT CURRENT
vs. DATA RATE
6
5
7
9
8
MAX220-02
DATA RATE (kb/s)
OUTPUT CURRENT (mA)
20 30 50
OUTPUT LOAD CURRENT
FLOWS FROM V+ TO V-
VCC = +5.25V
ALL CAPS
1μF
ALL CAPS
0.1μFVCC = +4.75V
+10V
-10V
MAX222/MAX242
ON-TIME EXITING SHUTDOWN
+5V
+5V
0V
0V
MAX220-03
500μs/div
V+, V- VOLTAGE (V)
1μF CAPS V+
V+
V-
V-
SHDN
0.1μF CAPS
1μF CAPS
0.1μF CAPS
ELECTRICAL CHARACTERISTICS—MAX220/222/232A/233A/242/243 (continued)
(VCC = +5V ±10%, C1–C4 = 0.1µF‚ MAX220, C1 = 0.047µF, C2–C4 = 0.33µF, TA= TMIN to TMAX‚ unless otherwise noted.) (Note 3)
PARAMETER CONDITIONS MIN TYP MAX UNITS
MAX222/MAX232A/MAX233/
MAX242/MAX243 0.5 1
tPHLR, Figure 2
MAX220 0.6 3
MAX222/MAX232A/MAX233/
MAX242/MAX243 0.6 1
Receiver Propagation Delay RS-232 to
TLL (Normal Operation)
tPLHR, Figure 2
MAX220 0.8 3
μs
tPHLS, Figure 2 MAX242 0.5 10
Receiver Propagation Delay RS-232 to
TLL (Shutdown) tPHLS, Figure 2 MAX242 2.5 10 μs
Receiver-Output Enable Time tER MAX242, Figure 3 125 500 ns
Receiver-Output Disable Time tDR MAX242, Figure 3 160 500 ns
Transmitter-Output Enable Time
(SHDN Goes High) tET
MAX222/MAX242, 0.1μF
caps (includes charge-pump
start-up), Figure 4
250 μs
Transmitter-Output Disable Time
(SHDN Goes Low) tDT MAX222/MAX242,
0.1μF caps, Figure 4 600 ns
MAX222/MAX232A/MAX233/
MAX242/MAX243 300
Transmitter + to - Propagation Delay
Difference (Normal Operation) tPHLT - tPLHT
MAX220 2000
ns
MAX222/MAX232A/MAX233/
MAX242/MAX243 100
Receiver + to - Propagation Delay
Difference (Normal Operation) tPHLR - tPLHR
MAX220 225
ns
Note 3: All units are production tested at hot. Specifications over temperature are guaranteed by design.
Note 4: MAX243 R2OUT is guaranteed to be low when R2IN ≥0V or is unconnected.
4
Maxim Integrated
MAX220–MAX249
MAX220–MAX249
+5V-Powered, Multichannel RS-232
Drivers/Receivers
(Voltages referenced to GND.)
VCC ...........................................................................-0.3V to +6V
V+ ................................................................(VCC - 0.3V) to +14V
V- ............................................................................+0.3V to -14V
Input Voltages
TIN ............................................................-0.3V to (VCC + 0.3V)
RIN .....................................................................................±30V
Output Voltages
TOUT ..................................................(V+ + 0.3V) to (V- - 0.3V)
ROUT........................................................-0.3V to (VCC + 0.3V)
Short-Circuit Duration, TOUT to GND ........................Continuous
Continuous Power Dissipation (TA= +70°C)
14-Pin Plastic DIP (derate 10.00mW/°C above +70°C)....800mW
16-Pin Plastic DIP (derate 10.53mW/°C above +70°C)....842mW
20-Pin Plastic DIP (derate 11.11mW/°C above +70°C)....889mW
24-Pin Narrow Plastic DIP
(derate 13.33mW/°C above +70°C) ..........1.07W
24-Pin Plastic DIP (derate 9.09mW/°C above +70°C)......500mW
16-Pin Wide SO (derate 9.52mW/°C above +70°C).........762mW
20-Pin Wide SO (derate 10.00mW/°C above +70°C).......800mW
24-Pin Wide SO (derate 11.76mW/°C above +70°C).......941mW
28-Pin Wide SO (derate 12.50mW/°C above +70°C) .............1W
44-Pin Plastic FP (derate 11.11mW/°C above +70°C) .....889mW
14-Pin CERDIP (derate 9.09mW/°C above +70°C) ..........727mW
16-Pin CERDIP (derate 10.00mW/°C above +70°C) ........800mW
20-Pin CERDIP (derate 11.11mW/°C above +70°C) ........889mW
24-Pin Narrow CERDIP
(derate 12.50mW/°C above +70°C) ..............1W
24-Pin Sidebraze (derate 20.0mW/°C above +70°C)..........1.6W
28-Pin SSOP (derate 9.52mW/°C above +70°C).............762mW
Operating Temperature Ranges
MAX2 _ _ C _ _......................................................0°C to +70°C
MAX2 _ _ E _ _ ...................................................-40°C to +85°C
MAX2 _ _ M _ _......................................................-55°C to +125°C
Storage Temperature Range .............................-65°C to +160°C
Lead Temperature (soldering, 10s) .................................+300°C
Soldering Temperature (reflow)
20 PDIP (P20M+1) .........................................................+225°C
24 PDIP (P24M-1) ..........................................................+225°C
All other lead(Pb)-free packages...................................+260°C
All other packages containing lead(Pb) ...........................+240°C
ABSOLUTE MAXIMUM RATINGS—MAX223/MAX230–MAX241
ELECTRICAL CHARACTERISTICS—MAX223/MAX230–MAX241
(MAX223/230/232/234/236/237/238/240/241, VCC = +5V ±10%; MAX233/MAX235, VCC = +5V ±5%‚ C1–C4 = 1.0µF;
MAX231/MAX239, VCC = +5V ±10%; V+ = +7.5V to +13.2V; TA= TMIN to TMAX; unless otherwise noted.) (Note 5)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
CONDITIONS MIN TYP MAX UNITS
Output Voltage Swing All transmitter outputs loaded with 3kΩto ground ±5.0 ±7.3 V
VCC Supply Current No load,
TA= +25°C
510
mA
715
0.4 1
V+ Supply Current 1.8 5 mA
515
Shutdown Supply Current TA= +25°C 15 50
VInput Logic-High Voltage
TIN 2.0
EN, SHDN (MAX223);
EN, SHDN (MAX230/235/236/240/241) 2.4
Logic Pullup Current VTIN =0V 1.5 200
Receiver Input Voltage
Operating Range -30 +30 V
µA
µA
110
VInput Logic-Low Voltage TIN, EN, SHDN (MAX233); EN, SHDN (MAX230/235–241) 0.8
MAX231/239
MAX223/230/234–238/240/241
MAX232/233
PARAMETER
MAX239
MAX230/235/236/240/241
MAX231
MAX223
Maxim Integrated
5
MAX220–MAX249
MAX220–MAX249
mA
+5V-Powered, Multichannel RS-232
Drivers/Receivers
V
0.8 1.2
PARAMETER MIN TYP MAX UNITSCONDITIONS
Normal operation
VSHDN = 5V (MAX223)
VSHDN = 0V (MAX235/236/240/241)
1.7 2.4
RS-232 Input Logic-Low Voltage TA= +25°C,
VCC = +5V
0.6 1.5
VRS-232 Input Logic-High Voltage TA= +25°C,
VCC = +5V Shutdown (MAX223)
VSHDN = 0V,
VEN = +5V (R4IN‚ R5IN)
1.5 2.4
ELECTRICAL CHARACTERISTICS—MAX223/MAX230–MAX241 (continued)
(MAX223/230/232/234/236/237/238/240/241, VCC = +5V ±10%; MAX233/MAX235, VCC = +5V ±5%‚ C1–C4 = 1.0µF;
MAX231/MAX239, VCC = +5V ±10%; V+ = +7.5V to +13.2V; TA= TMIN to TMAX; unless otherwise noted.) (Note 5)
Shutdown (MAX223)
VSHDN = 0V,
VEN = +5V (R4IN, R5IN)
Normal operation
VSHDN = +5V (MAX223)
VSHDN = 0V (MAX235/236/240/241)
RS-232 Input Hysteresis VCC = +5V, no hysteresis in shutdown 0.2 0.5 1.0 V
RS-232 Input Resistance TA= +25°C, VCC = +5V 357kΩ
TTL/CMOS Output Voltage Low IOUT = 1.6mA (MAX231/232/233, IOUT = 3.2mA) 0.4 V
TTL/CMOS Output Voltage High IOUT = -1mA 3.5 VCC - 0.4 V
TTL/CMOS Output Leakage Current 0V ≤ROUT ≤VCC; VEN = 0V (MAX223);
VEN = VCC (MAX235–241) ±0.05 ±10 µA
MAX223 600 nsReceiver Output Enable Time Normal
operation MAX235/236/239/240/241 400
MAX223 900 nsReceiver Output Disable Time Normal
operation MAX235/236/239/240/241 250
Normal operation 0.5 10
µs
VSHDN = 0V
(MAX223)
440
Propagation Delay
RS-232 IN to
TTL/CMOS OUT,
CL= 150pF 640
3 5.1 30
V/µs
MAX231/MAX232/MAX233, TA= +25°C, VCC = +5V,
RL= 3kΩto 7kΩ, CL= 50pF to 2500pF, measured from
+3V to -3V or -3V to +3V
430
Transmitter Output Resistance VCC = V+ = V- = 0V, VOUT = ±2V 300 Ω
Transmitter Output Short-Circuit
Current ±10 mA
tPHLS
tPLHS
Transition Region Slew Rate
MAX223/MAX230/MAX234–241, TA= +25°C, VCC = +5V,
RL= 3kΩto 7kΩ‚ CL= 50pF to 2500pF, measured from
+3V to -3V or -3V to +3V
Note 5: All units are production tested at hot except for the MAX240, which is production tested at TA= +25°C. Specifications over
temperature are guaranteed by design.
6
Maxim Integrated
MAX220–MAX249
MAX220–MAX249
+5V-Powered, Multichannel RS-232
Drivers/Receivers
8.5
6.5
4.5 5.5
TRANSMITTER OUTPUT
VOLTAGE (VOH) vs. VCC
7.0
8.0
MAX220-04
VCC (V)
VOH (V)
5.0
7.5
1 TRANSMITTER
LOADED 3 TRANS-
MITTERS
LOADED
4 TRANSMITTERS
LOADED
2 TRANSMITTERS
LOADED
TA = +25°C
C1–C4 = 1μF
TRANSMITTER
LOADS =
3kΩ || 2500pF
7.4
6.0
0 2500
TRANSMITTER OUTPUT VOLTAGE (VOH)
vs. LOAD CAPACITANCE AT
DIFFERENT DATA RATES
6.4
6.2
7.2
7.0
MAX220-05
LOAD CAPACITANCE (pF)
VOH (V)
15001000500 2000
6.8
6.6
160kb/s
80kb/s
20kb/s
TA = +25°C
VCC = +5V
3 TRANSMITTERS LOADED
RL = 3kΩ
C1–C4 = 1μF
12.0
4.0
0 2500
TRANSMITTER SLEW RATE
vs. LOAD CAPACITANCE
6.0
5.0
11.0
9.0
10.0
MAX220-06
LOAD CAPACITANCE (pF)
SLEW RATE (V/μs)
15001000500 2000
8.0
7.0
TA = +25°C
VCC = +5V
LOADED, RL = 3kΩ
C1–C4 = 1μF
1 TRANSMITTER LOADED
2 TRANSMITTERS
LOADED
3 TRANSMITTERS
LOADED
4 TRANSMITTERS
LOADED
-6.0
-9.0
4.5 5.5
TRANSMITTER OUTPUT
VOLTAGE (VOL) vs. VCC
-8.0
-8.5
-6.5
-7.0
MAX220-07
VCC (V)
VOL (V)
5.0
-7.5
4 TRANS-
MITTERS
LOADED
TA = +25°C
C1–C4 = 1μF
TRANSMITTER
LOADS =
3kΩ || 2500pF
1 TRANS-
MITTER
LOADED
2 TRANS-
MITTERS
LOADED
3 TRANS-
MITTERS
LOADED
-6.0
-7.6
0 2500
TRANSMITTER OUTPUT VOLTAGE (VOL)
vs. LOAD CAPACITANCE AT
DIFFERENT DATA RATES
-7.0
-7.2
-7.4
-6.2
-6.4
MAX220-08
LOAD CAPACITANCE (pF)
VOL (V)
15001000500 2000
-6.6
-6.8 160kb/s
80kb/s
20kb/s
TA = +25°C
VCC = +5V
3 TRANSMITTERS LOADED
RL = 3kΩ
C1–C4 = 1μF
10
-10
05 10 15 20 25 30 35 40 45 50
TRANSMITTER OUTPUT VOLTAGE (V+, V-)
vs. LOAD CURRENT
-2
-6
-4
-8
8
6
MAX220-09
CURRENT (mA)
V+, V- (V)
4
2
0
V+ AND V-
EQUALLY
LOADED
V- LOADED,
NO LOAD
ON V+
TA = +25°C
VCC = +5V
C1–C4 = 1μF
ALL TRANSMITTERS UNLOADED
V+ LOADED,
NO LOAD
ON V-
__________________________________________Typical Operating Characteristics
MAX223/MAX230–MAX241
*SHUTDOWN POLARITY IS REVERSED
V+, V- WHEN EXITING SHUTDOWN
(1μF CAPACITORS)
MAX220-13
VSHDN*
V-
O
V+
500ms/div
Maxim Integrated
7
MAX220–MAX249
MAX220–MAX249
Input Logic-Low Voltage
+5V-Powered, Multichannel RS-232
Drivers/Receivers
ABSOLUTE MAXIMUM RATINGS—MAX225/MAX244–MAX249
ELECTRICAL CHARACTERISTICS—MAX225/MAX244–MAX249
(MAX225, VCC = +5.0V ±5%; MAX244–MAX249, VCC = +5.0V ±10%, external capacitors C1–C4 = 1µF; TA= TMIN to TMAX; unless
otherwise noted.) (Note 7)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
(Voltages referenced to GND.)
Supply Voltage (VCC) ...............................................-0.3V to +6V
Input Voltages
TIN‚ ENA, ENB, ENR, ENT, ENRA,
ENRB, ENTA, ENTB..................................-0.3V to (VCC + 0.3V)
RIN .....................................................................................±25V
TOUT (Note 6)....................................................................±15V
ROUT........................................................-0.3V to (VCC + 0.3V)
Short Circuit Duration (one output at a time)
TOUT to GND ...........................................................Continuous
ROUT to GND...........................................................Continuous
Continuous Power Dissipation (TA= +70°C)
28-Pin Wide SO (derate 12.50mW/°C above +70°C) .............1W
40-Pin Plastic DIP (derate 11.11mW/°C above +70°C) ...611mW
44-Pin PLCC (derate 13.33mW/°C above +70°C) ...........1.07W
Operating Temperature Ranges
MAX225C_ _, MAX24_C_ _ ..................................0°C to +70°C
MAX225E_ _, MAX24_E_ _ ...............................-40°C to +85°C
Storage Temperature Range .............................-65°C to +160°C
Lead Temperature (soldering,10s)) .................................+300°C
Soldering Temperature (reflow)
40 PDIP (P40M-2) ..........................................................+225°C
All other lead(Pb)-free packages...................................+260°C
All other packages containing lead(Pb) ........................+240°C
VCC = 0V,
VOUT = ±15V
µATables 1a–1d
±0.01 ±25
Normal operation
Shutdown
Tables 1a–1d, normal operation
All transmitter outputs loaded with 3kΩto GND
VENA, VENB, VENT, VENTA,
VENTB = VCC, VOUT = ±15V
VRS-232 Input Hysteresis
RS-232 Input Logic-Low Voltage V
V±5 ±7.5Output Voltage Swing
Output Leakage Current (Shutdown)
±0.01 ±25
Ω300 10MVCC = V+ = V- = 0V, VOUT = ±2V (Note 8)Transmitter Output Resistance
µA
PARAMETER
±0.05 ±0.10
MIN TYP MAX UNITS
Normal operation, outputs disabled,
Tables 1a–1d, 0V ≤VOUT ≤VCC, VENR_ = VCC
TTL/CMOS Output Leakage Current
10 30Sinking VOUT = VCC
mA
-2 -10Sourcing VOUT = VGND
V3.5 VCC - 0.2IOUT = -1.0mATTL/CMOS Output Voltage High
V0.2 0.4IOUT = 3.2mATTL/CMOS Output Voltage Low
kΩ357
0.2 0.5 1.0VCC = +5V
1.4 0.8 V
TTL/CMOS Output Short-Circuit Current
V1.8 2.4
0.8 1.3VCC = +5V
RS-232 Input Resistance
V±25RS-232 Input Voltage Operating Range
mA±7 ±30VOUT = 0VOutput Short-Circuit Current
kbps120 64Data Rate
CONDITIONS
VCC = +5V
µA
±0.01 ±1
Logic Pullup/lnput Current 10 50
Tables 1a–1d
RS-232 Input Logic-High Voltage
V2 1.4Input Logic-High Voltage
RS-232 TRANSMITTERS
RS-232 RECEIVERS
Note 6: Input voltage measured with transmitter output in a high-impedance state, shutdown, or VCC = 0V.
8
Maxim Integrated
MAX220–MAX249
MAX220–MAX249
+5V-Powered, Multichannel RS-232
Drivers/Receivers
Supply Voltage Range 4.75 5.25 V
Transmitter Enable Time
MAX225 10 20
tET
No load MAX244–MAX249 11 30
51030
MAX225 40
VCC Supply Current
(Normal Operation) 3kΩloads on
all outputs MAX244–MAX249 57
mA
Transition Slew Rate
825
CL= 50pF to 2500pF, RL= 3kΩto 7kΩ, VCC = +5V,
TA= +25°C, measured from +3V to -3V or -3V to +3V
TA= TMIN to TMAX
CONDITIONS
50
V/µs
MAX246–MAX249
(excludes charge-pump startup)
Shutdown Supply Current µA
5
tPHLT, Figure 1 1.3 3.5
µs
tPLHT, Figure 1 1.5 3.5
Transmitter Disable Time
Transmitter Propagation Delay
TLL to RS-232 (Normal Operation) µs
tDT, Figure 4 100 ns
Transmitter + to - Propagation
Delay Difference (Normal Operation) tPHLT - tPLHT
UNITSMIN TYP MAX
350
PARAMETER
ns
Receiver + to - Propagation
Delay Difference (Normal Operation) tPHLR - tPLHR 350 ns
4.5 5.5MAX244–MAX249
MAX225
Leakage current ±1
Logic-low voltage 1.4 0.8
Control Input
Logic-high voltage 2.4 1.4 V
µA
TA= +25°C
tPHLR, Figure 2 0.6 1.5
tPLHR, Figure 2 0.6 1.5
Receiver Propagation Delay
TLL to RS-232 (Normal Operation) µs
tPHLS, Figure 2 0.6 10
tPLHS, Figure 2 3.0 10
Receiver Propagation Delay
TLL to RS-232 (Low-Power Mode) µs
Receiver-Output Enable Time tER, Figure 3 100 500 ns
Receiver-Output Disable Time tDR, Figure 3 100 500 ns
MAX225/MAX245–MAX249
(includes charge-pump startup) 10 ms
POWER SUPPLY AND CONTROL LOGIC
AC CHARACTERISTICS
Note 7: All units production tested at hot. Specifications over temperature are guaranteed by design.
Note 8: The 300Ωminimum specification complies with EIA/TIA-232E, but the actual resistance when in shutdown mode or VCC =
0V is 10MΩas is implied by the leakage specification.
ELECTRICAL CHARACTERISTICS—MAX225/MAX244–MAX249 (continued)
(MAX225, VCC = +5.0V ±5%; MAX244–MAX249, VCC = +5.0V ±10%, external capacitors C1–C4 = 1µF; TA= TMIN to TMAX; unless
otherwise noted.) (Note 7)
Maxim Integrated
9
MAX220–MAX249
MAX220–MAX249
+5V-Powered, Multichannel RS-232
Drivers/Receivers
__________________________________________Typical Operating Characteristics
MAX225/MAX244–MAX249
18
2
012345
TRANSMITTER SLEW RATE
vs. LOAD CAPACITANCE
8
6
4
16
MAX220-10
LOAD CAPACITANCE (nF)
TRANSMITTER SLEW RATE (V/μs)
14
12
10
VCC = +5V
EXTERNAL POWER SUPPLY
1μF CAPACITORS
40kb/s DATA RATE
8 TRANSMITTERS
LOADED WITH 3kΩ
10
-10
05 10 15 20 25 30 35
OUTPUT VOLTAGE
vs. LOAD CURRENT FOR V+ AND V-
-2
-4
-6
-8
8
MAX220-11
LOAD CURRENT (mA)
OUTPUT VOLTAGE (V)
6
4
2
0
V+ AND V- LOADED
EITHER V+ OR
V- LOADED
V+ AND V- LOADED
VCC = +5V
EXTERNAL CHARGE PUMP
1μF CAPACITORS
8 TRANSMITTERS
DRIVING 5kΩ AND
2000pF AT 20kb/s
V- LOADED
V+ LOADED
9.0
5.0
012345
TRANSMITTER OUTPUT VOLTAGE (V+, V-)
vs. LOAD CAPACITANCE AT
DIFFERENT DATA RATES
6.0
5.5
8.5
MAX220-12
LOAD CAPACITANCE (nF)
V+, V- (V)
8.0
7.5
7.0
6.5
VCC = +5V WITH ALL TRANSMITTERS DRIVEN
LOADED WITH 5kΩ
40kb/s
60kb/s
100kb/s
200kb/s
ALL CAPACITIORS 1μF
10kb/s
20kb/s
10
Maxim Integrated
MAX220–MAX249
MAX220–MAX249
+5V-Powered, Multichannel RS-232
Drivers/Receivers
INPUT
OUTPUT
+3V
V+
0V
V-
0V
tPLHT tPHLT
tPHLR
tPHLS
tPLHR
tPLHS
50%
VCC
50%
+3V
50%
INPUT
OUTPUT
*EXCEPT FOR R2 ON THE MAX243
WHERE -3V IS USED.
0V*
50%
GND
Figure 1. Transmitter Propagation-Delay Timing Figure 2. Receiver Propagation-Delay Timing
EN
RX IN
a) TEST CIRCUIT
b) ENABLE TIMING
c) DISABLE TIMING
EN INPUT
RECEIVER
OUTPUTS
RX OUT
RX
1kΩ
0V
+3V
EN
EN
+0.8V
+3.5V
OUTPUT ENABLE TIME (tER)
VCC - 2V
VOL + 0.5V
VOH - 0.5V
OUTPUT DISABLE TIME (tDR)
VCC - 2V
+3V
0V
150pF
EN INPUT
VOH
RECEIVER
OUTPUTS
VOL
1 OR 0 TX
3kΩ50pF
-5V
+5V
OUTPUT DISABLE TIME (tDT)
V+
SHDN +3V
0V
V-
0V
a) TIMING DIAGRAM
b) TEST CIRCUIT
Figure 3. Receiver-Output Enable and Disable Timing Figure 4. Transmitter-Output Disable Timing
Test Circuits/Timing Diagrams
Maxim Integrated
11
MAX220–MAX249
MAX220–MAX249
+5V-Powered, Multichannel RS-232
Drivers/Receivers
ENT ENR OPERATION STATUS TRANSMITTERS RECEIVERS
0 0 Normal Operation All Active All Active
0 1 Normal Operation All Active All High-Z
1 0 Shutdown All High-Z All Low-Power Receive Mode
1 1 Shutdown All High-Z All High-Z
Table 1a. MAX245 Control Pin Configurations
ENT ENR OPERATION
STATUS
TRANSMITTERS RECEIVERS
TA1–TA4 TB1–TB4 RA1–RA5 RB1–RB5
0 0 Normal Operation All Active All Active All Active All Active
0 1 Normal Operation All Active All Active RA1–RA4 High-Z,
RA5 Active
RB1–RB4 High-Z,
RB5 Active
1 0 Shutdown All High-Z All High-Z All Low-Power
Receive Mode
All Low-Power
Receive Mode
1 1 Shutdown All High-Z All High-Z
RA1–RA4 High-Z,
RA5 Low-Power
Receive Mode
RB1–RB4 High-Z,
RB5 Low-Power
Receive Mode
Table 1b. MAX245 Control Pin Configurations
Table 1c. MAX246 Control Pin Configurations
ENA ENB OPERATION
STATUS
TRANSMITTERS RECEIVERS
TA1–TA4 TB1–TB4 RA1–RA5 RB1–RB5
0 0 Normal Operation All Active All Active All Active All Active
0 1 Normal Operation All Active All High-Z All Active RB1–RB4 High-Z,
RB5 Active
1 0 Shutdown All High-Z All Active RA1–RA4 High-Z,
RA5 Active All Active
1 1 Shutdown All High-Z All High-Z
RA1–RA4 High-Z,
RA5 Low-Power
Receive Mode
RB1–RB4 High-Z,
RA5 Low-Power
Receive Mode
Control Pin Configuration Tables
12
Maxim Integrated
MAX220–MAX249
MAX220–MAX249
+5V-Powered, Multichannel RS-232
Drivers/Receivers
TA1–TA4 TB1–TB4 RA1–RA4 RB1–RB4
0 0 0 0 Normal Operation All Active All Active All Active All Active
0 0 0 1 Normal Operation All Active All Active All Active
All High-Z, except
RB5 stays active on
MAX247
0 0 1 0 Normal Operation All Active All Active All High-Z All Active
0 0 1 1 Normal Operation All Active All Active All High-Z
All High-Z, except
RB5 stays active on
MAX247
0 1 0 0 Normal Operation All Active All High-Z All Active All Active
0 1 0 1 Normal Operation All Active All High-Z All Active
All High-Z, except
RB5 stays active on
MAX247
0 1 1 0 Normal Operation All Active All High-Z All High-Z All Active
0 1 1 1 Normal Operation All Active All High-Z All High-Z
All High-Z, except
RB5 stays active on
MAX247
1 0 0 0 Normal Operation All High-Z All Active All Active All Active
1 0 0 1 Normal Operation All High-Z All Active All Active
All High-Z, except
RB5 stays active on
MAX247
1 0 1 0 Normal Operation All High-Z All Active All High-Z All Active
1 0 1 1 Normal Operation All High-Z All Active All High-Z
All High-Z, except
RB5 stays active on
MAX247
1 1 0 0 Shutdown All High-Z All High-Z Low-Power
Receive Mode
Low-Power
Receive Mode
1 1 0 1 Shutdown All High-Z All High-Z Low-Power
Receive Mode
All High-Z, except
RB5 stays active on
MAX247
1 1 1 0 Shutdown All High-Z All High-Z All High-Z Low-Power
Receive Mode
1 1 1 1 Shutdown All High-Z All High-Z All High-Z
All High-Z, except
RB5 stays active on
MAX247
Table 1d. MAX247/MAX248/MAX249 Control Pin Configurations
MAX248
OPERATION
STATUS
ENRB MAX247 TA1–TA4 TB1–TB4 RA1–RA4 RB1–RB5
TRANSMITTERS
ENRAENTBENTA
MAX249 TA1–TA3 TB1–TB3 RA1–RA5 RB1–RB5
RECEIVERS
Maxim Integrated
13
MAX220–MAX249
MAX220–MAX249
_______________Detailed Description
The MAX220–MAX249 contain four sections: dual
charge-pump DC-DC voltage converters, RS-232 dri-
vers, RS-232 receivers, and receiver and transmitter
enable control inputs.
Dual Charge-Pump Voltage Converter
The MAX220–MAX249 have two internal charge-pumps
that convert +5V to ±10V (unloaded) for RS-232 driver
operation. The first converter uses capacitor C1 to dou-
ble the +5V input to +10V on C3 at the V+ output. The
second converter uses capacitor C2 to invert +10V to
-10V on C4 at the V- output.
A small amount of power may be drawn from the +10V
(V+) and -10V (V-) outputs to power external circuitry
(see the
Typical Operating Characteristics
section),
except on the MAX225 and MAX245–MAX247, where
these pins are not available. V+ and V- are not regulated,
so the output voltage drops with increasing load current.
Do not load V+ and V- to a point that violates the mini-
mum ±5V EIA/TIA-232E driver output voltage when
sourcing current from V+ and V- to external circuitry.
When using the shutdown feature in the MAX222,
MAX225, MAX230, MAX235, MAX236, MAX240,
MAX241, and MAX245–MAX249, avoid using V+ and V-
to power external circuitry. When these parts are shut
down, V- falls to 0V, and V+ falls to +5V. For applica-
tions where a +10V external supply is applied to the V+
pin (instead of using the internal charge pump to gen-
erate +10V), the C1 capacitor must not be installed and
the SHDN pin must be connected to VCC. This is
because V+ is internally connected to VCC in shutdown
mode.
RS-232 Drivers
The typical driver output voltage swing is ±8V when
loaded with a nominal 5kΩRS-232 receiver and VCC =
+5V. Output swing is guaranteed to meet the EIA/TIA-
232E and V.28 specification, which calls for ±5V mini-
mum driver output levels under worst-case conditions.
These include a minimum 3kΩload, VCC = +4.5V, and
maximum operating temperature. Unloaded driver out-
put voltage ranges from (V+ -1.3V) to (V- +0.5V).
Input thresholds are both TTL and CMOS compatible.
The inputs of unused drivers can be left unconnected
since 400kΩinput pullup resistors to VCC are built in
(except for the MAX220). The pullup resistors force the
outputs of unused drivers low because all drivers invert.
The internal input pullup resistors typically source 12µA,
except in shutdown mode where the pullups are dis-
abled. Driver outputs turn off and enter a high-imped-
ance state—where leakage current is typically
microamperes (maximum 25µA)—when in shutdown
mode, in three-state mode, or when device power is
removed. Outputs can be driven to ±15V. The power-
supply current typically drops to 8µA in shutdown mode.
The MAX220 does not have pullup resistors to force the
outputs of the unused drivers low. Connect unused
inputs to GND or VCC.
The MAX239 has a receiver three-state control line, and
the MAX223, MAX225, MAX235, MAX236, MAX240,
and MAX241 have both a receiver three-state control
line and a low-power shutdown control. Table 2 shows
the effects of the shutdown control and receiver three-
state control on the receiver outputs.
The receiver TTL/CMOS outputs are in a high-imped-
ance, three-state mode whenever the three-state enable
line is high (for the MAX225/MAX235/MAX236/MAX239–
MAX241), and are also high-impedance whenever the
shutdown control line is high.
When in low-power shutdown mode, the driver outputs
are turned off and their leakage current is less than 1µA
with the driver output pulled to ground. The driver output
leakage remains less than 1µA, even if the transmitter
output is backdriven between 0V and (VCC + 6V). Below
-0.5V, the transmitter is diode clamped to ground with
1kΩseries impedance. The transmitter is also zener
clamped to approximately VCC + 6V, with a series
impedance of 1kΩ.
The driver output slew rate is limited to less than 30V/µs
as required by the EIA/TIA-232E and V.28 specifica-
tions. Typical slew rates are 24V/µs unloaded and
10V/µs loaded with 3Ωand 2500pF.
RS-232 Receivers
EIA/TIA-232E and V.28 specifications define a voltage
level greater than 3V as a logic 0, so all receivers invert.
Input thresholds are set at 0.8V and 2.4V, so receivers
respond to TTL level inputs as well as EIA/TIA-232E and
V.28 levels.
The receiver inputs withstand an input overvoltage up
to ±25V and provide input terminating resistors with
+5V-Powered, Multichannel RS-232
Drivers/Receivers
PART SHDN EN EN(R) RECEIVERS
MAX223 __
Low
High
High
X
Low
High
High Impedance
Active
High Impedance
MAX225 __ __ High Impedance
Active
__
MAX235
MAX236
MAX240
Low
Low
High
__ __
Low
High
X
High Impedance
Active
High Impedance
Table 2. Three-State Control of Receivers
Low
High
SHDN
__
14
Maxim Integrated
MAX220–MAX249
MAX220–MAX249
+5V-Powered, Multichannel RS-232
Drivers/Receivers
nominal 5kΩvalues. The receivers implement Type 1
interpretation of the fault conditions of V.28 and
EIA/TIA-232E.
The receiver input hysteresis is typically 0.5V with a
guaranteed minimum of 0.2V. This produces clear out-
put transitions with slow-moving input signals, even
with moderate amounts of noise and ringing. The
receiver propagation delay is typically 600ns and is
independent of input swing direction.
Low-Power Receive Mode
The low-power receive mode feature of the MAX223,
MAX242, and MAX245–MAX249 puts the IC into shut-
down mode but still allows it to receive information. This
is important for applications where systems are periodi-
cally awakened to look for activity. Using low-power
receive mode, the system can still receive a signal that
will activate it on command and prepare it for communi-
cation at faster data rates. This operation conserves
system power.
Negative Threshold—MAX243
The MAX243 is pin compatible with the MAX232A, differ-
ing only in that RS-232 cable fault protection is removed
on one of the two receiver inputs. This means that control
lines such as CTS and RTS can either be driven or left
unconnected without interrupting communication.
Different cables are not needed to interface with different
pieces of equipment.
The input threshold of the receiver without cable fault
protection is -0.8V rather than +1.4V. Its output goes
positive only if the input is connected to a control line
that is actively driven negative. If not driven, it defaults
to the 0 or “OK to send” state. Normally‚ the MAX243’s
other receiver (+1.4V threshold) is used for the data line
(TD or RD)‚ while the negative threshold receiver is con-
nected to the control line (DTR‚ DTS‚ CTS‚ RTS, etc.).
Other members of the RS-232 family implement the
optional cable fault protection as specified by EIA/TIA-
232E specifications. This means a receiver output goes
high whenever its input is driven negative‚ left uncon-
nected‚ or shorted to ground. The high output tells the
serial communications IC to stop sending data. To
avoid this‚ the control lines must either be driven or
connected with jumpers to an appropriate positive volt-
age level.
Shutdown—MAX222–MAX242
On the MAX222‚ MAX235‚ MAX236‚ MAX240‚ and
MAX241‚ all receivers are disabled during shutdown.
On the MAX223 and MAX242‚ two receivers continue to
operate in a reduced power mode when the chip is in
shutdown. Under these conditions‚ the propagation
delay increases to about 2.5µs for a high-to-low input
transition. When in shutdown, the receiver acts as a
CMOS inverter with no hysteresis. The MAX223 and
MAX242 also have a receiver output enable input (EN
for the MAX242 and EN for the MAX223) that allows
receiver output control independent of SHDN (SHDN
for MAX241). With all other devices‚ SHDN (SHDN for
MAX241) also disables the receiver outputs.
The MAX225 provides five transmitters and five
receivers‚ while the MAX245 provides ten receivers and
eight transmitters. Both devices have separate receiver
and transmitter-enable controls. The charge pumps
turn off and the devices shut down when a logic high is
applied to the ENT input. In this state, the supply cur-
rent drops to less than 25µA and the receivers continue
to operate in a low-power receive mode. Driver outputs
enter a high-impedance state (three-state mode). On
the MAX225‚ all five receivers are controlled by the
ENR input. On the MAX245‚ eight of the receiver out-
puts are controlled by the ENR input‚ while the remain-
ing two receivers (RA5 and RB5) are always active.
RA1–RA4 and RB1–RB4 are put in a three-state mode
when ENR is a logic high.
Receiver and Transmitter Enable
Control Inputs
The MAX225 and MAX245–MAX249 feature transmitter
and receiver enable controls.
The receivers have three modes of operation: full-speed
receive (normal active)‚ three-state (disabled)‚ and low-
power receive (enabled receivers continue to function
at lower data rates). The receiver enable inputs control
the full-speed receive and three-state modes. The
transmitters have two modes of operation: full-speed
transmit (normal active) and three-state (disabled). The
transmitter enable inputs also control the shutdown
mode. The device enters shutdown mode when all
transmitters are disabled. Enabled receivers function in
the low-power receive mode when in shutdown.
Maxim Integrated
15
MAX220–MAX249
MAX220–MAX249
Tables 1a–1d define the control states. The MAX244
has no control pins and is not included in these tables.
The MAX246 has ten receivers and eight drivers with
two control pins, each controlling one side of the
device. A logic high at the A-side control input (ENA)
causes the four A-side receivers and drivers to go into
a three-state mode. Similarly, the B-side control input
(ENB) causes the four B-side drivers and receivers to
go into a three-state mode. As in the MAX245, one A-
side and one B-side receiver (RA5 and RB5) remain
active at all times. The entire device is put into shut-
down mode when both the A and B sides are disabled
(ENA = ENB = +5V).
The MAX247 provides nine receivers and eight drivers
with four control pins. The ENRA and ENRB receiver
enable inputs each control four receiver outputs. The
ENTA and ENTB transmitter enable inputs each control
four drivers. The ninth receiver (RB5) is always active.
The device enters shutdown mode with a logic high on
both ENTA and ENTB.
The MAX248 provides eight receivers and eight drivers
with four control pins. The ENRA and ENRB receiver
enable inputs each control four receiver outputs. The
ENTA and ENTB transmitter enable inputs control four
drivers each. This part does not have an always-active
receiver. The device enters shutdown mode and trans-
mitters go into a three-state mode with a logic high on
both ENTA and ENTB.
The MAX249 provides ten receivers and six drivers with
four control pins. The ENRA and ENRB receiver enable
inputs each control five receiver outputs. The ENTA
and ENTB transmitter enable inputs control three dri-
vers each. There is no always-active receiver. The
device enters shutdown mode and transmitters go into
a three-state mode with a logic high on both ENTA and
ENTB. In shutdown mode, active receivers operate in a
low-power receive mode at data rates up to 20kb/s.
__________Applications Information
Figures 5 through 25 show pin configurations and typi-
cal operating circuits. In applications that are sensitive
to power-supply noise, VCC should be decoupled to
ground with a capacitor of the same value as C1 and
C2 connected as close as possible to the device.
+5V-Powered, Multichannel RS-232
Drivers/Receivers
16
Maxim Integrated
MAX220–MAX249
MAX220–MAX249
+5V-Powered, Multichannel RS-232
Drivers/Receivers
TOP VIEW
16
15
14
13
12
11
10
9
1
2
3
4
5
6
7
8
VCC
GND
T1OUT
R1IN
C2+
C1-
V+
C1+ +
MAX220
MAX232
MAX232A R1OUT
T1IN
T2IN
R2OUT
R2IN
T2OUT
V-
C2-
DIP/SO
V+
V-
2+10V
C1+
C1
C2
1
3
4
5
11
10
12
9
6
14
7
13
8
T1IN
R1OUT
T2IN
R2OUT
T1OUT
R1IN
T2OUT
R2IN
+5V INPUT
C2+ -10V
C4
RS-232
OUTPUTS
RS-232
INPUTS
TTL/CMOS
INPUTS
TTL/CMOS
OUTPUTS
GND
15
5kΩ
5kΩ
400kΩ
400kΩ
+5V
+5V
+10V TO -10V
VOLTAGE INVERTER
+5V TO +10V
VOLTAGE DOUBLER
16
C3
C5
CAPACITANCE (μF)
DEVICE
MAX220
MAX232
MAX232A
C1
0.047
1.0
0.1
C2
0.33
1.0
0.1
C3
0.33
1.0
0.1
C4
0.33
1.0
0.1
C5
0.33
1.0
0.1
C2-
C1-
VCC
5kΩ
DIP/SO
18
17
16
15
14
13
12
11
1
2
3
4
5
6
7
8
SHDN
VCC
GND
T1OUT
C1-
V+
C1+
(N.C.) EN
R1IN
R1OUT
T1IN
T2IN
T2OUT
V-
C2-
C2+
10
9R2OUT
R2IN
MAX222
MAX242
20
19
18
17
16
15
14
13
1
2
3
4
5
6
7
8
SHDN
VCC
GND
T1OUT
C1-
V+
C1+
(N.C.) EN
N.C.
R1IN
R1OUT
N.C.
T2OUT
V-
C2-
C2+
12
11
9
10
T1IN
T2IN
R2OUT
R2IN
MAX222
MAX242
SSOP
( ) ARE FOR MAX222 ONLY.
PIN NUMBERS IN TYPICAL OPERATING CIRCUIT ARE FOR DIP/SO PACKAGES ONLY.
V+
V-
3+10V
C1
C2
2
4
5
6
12
11
13
7
15
8
14
9
T1IN
R1OUT
T2IN
R2OUT
T1OUT
(EXCEPT MAX220)
(EXCEPT MAX220)
R1IN
T2OUT
R2IN
+5V INPUT
C2+ -10V
C4
RS-232
OUTPUTS
RS-232
INPUTS
TTL/CMOS
INPUTS
TTL/CMOS
OUTPUTS
GND
16
5kΩ
400kΩ
400kΩ
+5V
+5V
+10V TO -10V
VOLTAGE INVERTER
VCC
+5V TO +10V
VOLTAGE DOUBLER
17
C3
C5
1
10
18
SHDN
EN
(N.C.)
ALL CAPACITORS = 0.1μF
C2-
C1+
C1-
+
+
TOP VIEW
Figure 5. MAX220/MAX232/MAX232A Pin Configuration and Typical Operating Circuit
Figure 6. MAX222/MAX242 Pin Configurations and Typical Operating Circuit
Maxim Integrated
17
MAX220–MAX249
MAX220–MAX249
+5V-Powered, Multichannel RS-232
Drivers/Receivers
13
14
28
27
26
25
24
23
22
21
1
2
3
4
5
6
7
8
VCC
VCC VCC
400kΩ
400kΩ
400kΩ
400kΩ
400kΩ
T1OUT
+5V
+5V
0.1μF
+5V
3
28 27
4
25
24
23
26
5
6
7
22
GND
ENR
ENR
GND
21
+5V
+5V
+5V
T2OUT
T3OUT
T4OUT
5kΩ
5kΩ
5kΩ
5kΩ
5kΩ
14
13
2
1
T5OUT
T5OUT
R1IN
R2IN
R3IN
R4IN
R5IN
T1IN 11
12
18
17
16
15
10
9
8
19
20
T2IN
T3IN
T4IN
T5IN
ENT
R2OUT
R3OUT
R4OUT
PINS (ENR, GND, VCC, T5OUT) ARE INTERNALLY CONNECTED.
CONNECT EITHER OR BOTH EXTERNALLY. T5OUT IS A SINGLE DRIVER.
R5OUT
R1OUT
VCC
ENT
T3IN
T2IN
T1IN
ENR
ENR
T4IN
T5IN
R4OUT
R5OUT
R3IN
R3OUT
R2OUT
R1OUT
20
19
18
17
9
10
11
12
R5IN
R4IN
T3OUT
T4OUT
T2OUT
T1OUT
R1IN
R2IN
SO
MAX225
16
15
T5OUT
MAX225 FUNCTIONAL DESCRIPTION
5 RECEIVERS
5 TRANSMITTERS
2 CONTROL PINS
1 RECEIVER ENABLE (ENR)
1 TRANSMITTER ENABLE (ENT)
T5OUT
GND
GND
TOP VIEW
+
Figure 7. MAX225 Pin Configuration and Typical Operating Circuit
18
Maxim Integrated
MAX220–MAX249
MAX220–MAX249
+5V-Powered, Multichannel RS-232
Drivers/Receivers
GND
10
27R3OUT
23
R4OUT
R3IN
R4IN
5kΩ
5kΩ
54
R2OUT R2IN
5kΩ
RS-232
INPUTS
LOGIC
OUTPUTS
RS-232
OUTPUTS
TTL/CMOS
INPUTS
R2
89
R1OUT R1IN
5kΩ
R1
R3
R4
19 18
R5OUT R5IN
5kΩ
R5
2
7T1IN T1OUT
+5V
400kΩ
+5V
63
T2IN T2OUT
T2
400kΩ
20 T3OUT 1
T3IN
+5V
T3
400kΩ
C1+
C1-
1.0μF
12 VCC
+5V INPUT
11
17
1.0μF
13
1.0μF
+5V TO +10V
VOLTAGE DOUBLER
26
1.0μF
T1
28
21 T4IN T4OUT
+5V
400kΩ
T4
14
C2+
C2-
15
1.0μF16
+10V TO -10V
VOLTAGE INVERTER
V+
22
EN (EN)
24 25
28
27
26
25
24
23
22
21
20
19
18
17
16
15
1
2
3
4
5
6
7
8
9
10
11
12
13
14
T4OUT
R3IN
R3OUT
SHDN (SHDN)
R4IN*
C2+
R4OUT*
T4IN
T3IN
R5OUT*
R5IN*
V-
C2-
C1-
V+
C1+
VCC
GND
R1IN
R1OUT
T1IN
T2IN
R2OUT
R2IN
T2OUT
T1OUT
T3OUT
Wide SO/
SSOP
MAX223
MAX241
EN (EN)
SHDN
(SHDN)
*R4 AND R5 IN MAX223 REMAIN ACTIVE IN SHUTDOWN.
NOTE: PIN LABELS IN ( ) ARE FOR MAX241.
V-
+
TOP VIEW
Figure 8. MAX223/MAX241 Pin Configuration and Typical Operating Circuit
Maxim Integrated
19
MAX220–MAX249
MAX220–MAX249
+5V-Powered, Multichannel RS-232
Drivers/Receivers
20
19
18
17
16
15
14
13
1
2
3
4
5
6
7
8
T5IN
N.C.
SHDN
T2IN
T2OUT
T1OUT
T5OUT
T4IN
T3IN
V-
C1+
VCC
GND
T1IN
12
11
9
10
C2-
C2+
C1-
V+
DIP/SO
MAX230
V+
V-
9
C1+
C1-
8
10
11
12
5
4
14
13
2
3
1
20
T3IN
T4IN
T2IN
T5IN
T1OUT
T2OUT
+5V INPUT
C2+
C2-
RS-232
OUTPUTS
TTL/CMOS
INPUTS
GND
6
400kΩ
+5V
400kΩ
+5V
400kΩ
+5V
400kΩ
+5V
400kΩ
+5V
+10V TO -10V
VOLTAGE INVERTER
VCC
+5V TO +10V
VOLTAGE DOUBLER
7
1.0μF
1.0μF
1.0μF
1.0μF
19
15
16
T3OUT T4OUT
18
x
T1IN
T3OUT
T4OUT
T5OUT
17
1.0μF
T2
T3
T4
T5
N.C. SHDN
T1
+
TOP VIEW
Figure 9. MAX230 Pin Configuration and Typical Operating Circuit
V+
V-
14
C1+
C1-
1
2
8
7
3
11
4
T2IN
T1IN T1OUT
T2OUT
+5V INPUT
RS-232
INPUTS
TTL/CMOS
OUTPUTS
GND
12 (14)
5kΩ
5kΩ
+12V TO -12V
VOLTAGE CONVERTER
13 (15)
1.0μF
1.0μF
C2
1.0μF
400kΩ
+5V
400kΩ
+5V
6
910
R1IN
R2IN
R2OUT
R1OUT
5
16
15
14
13
12
11
10
9
1
2
3
4
5
6
7
8
V+
VCC
GND
T1OUT
T2OUT
V-
C-
C+
MAX231
R1IN
R1OUT
T1IN
N.C.
N.C.
T2IN
R2OUT
R2IN
SO
(12)
RS-232
OUTPUTS
TTL/CMOS
INPUTS
(11)
(13)(10)
VCC
PIN NUMBERS IN ( ) ARE FOR SO PACKAGE.
14
13
12
11
10
9
8
1
2
3
4
5
6
7
V+
VCC
GND
T1OUTT2OUT
V-
C-
C+
MAX231
R1IN
R1OUT
T1INT2IN
R2OUT
R2IN
DIP
+7.5V TO +12V
(16)
T1
T2
R1
R2
++
TOP VIEW
Figure 10. MAX231 Pin Configurations and Typical Operating Circuit
20
Maxim Integrated
MAX220–MAX249
MAX220–MAX249
+5V-Powered, Multichannel RS-232
Drivers/Receivers
2
1
5
18
T2IN
T1IN T1OUT
T2OUT
+5V INPUT
RS-232
INPUTS
TTL/CMOS
OUTPUTS
GND GND
69
400kΩ
+5V
400kΩ
+5V
5kΩ
5kΩ
7
20
34
R1IN
R2IN
R2OUT
R1OUT
19
RS-232
OUTPUTS
TTL/CMOS
INPUTS
VCC
PIN NAMES IN ( ) ARE FOR SO PACKAGE.
20
19
18
17
16
15
14
13
1
2
3
4
5
6
7
8
R2IN
T2OUT
V-
R1IN
R1OUT
T1IN
C2-
C2+
V+ (C1-)
C1- (C1+)
(V+) C1+
VCC
GND
T1OUT
12
11
9
10
V- (C2+)
C2+ (C2-)
(V-) CS-
GND
DIP/SO
MAX233
MAX233A
T2IN R2OUT
C1+
C1-
V-
V-
V+
C2+
C2-
CS-
C2+
8 (13)
13 (14)
12 (10)
17
14 (8)
11 (12)
15
16
10 (11)
DO NOT MAKE
CONNECTIONS TO
THESE PINS
INTERNAL -10V
POWER SUPPLY
INTERNAL +10V
POWER SUPPLY
1.0μF
TOP VIEW
+
Figure 11. MAX233/MAX233A Pin Configuration and Typical Operating Circuit
16
15
14
13
12
11
10
9
1
2
3
4
5
6
7
8
T3OUT
T4OUT
T4IN
T3IN
T1IN
T2IN
T2OUT
T1OUT
MAX234
V-
C2-
C2+
C1-
V+
C1+
VCC
GND
DIP/SO
V+
V-
8
C1+
C1-
1.0μF
1.0μF
1.0μF
7
9
10
11
4
3
13
14
12
1
2
16
15
T1IN
T3IN
T2IN
T4IN
T1OUT
T3OUT
T2OUT
T4OUT
+5V INPUT
C2-
C2+
RS-232
OUTPUTS
TTL/CMOS
INPUTS
GND
5
+5V
+5V
+10V TO -10V
VOLTAGE INVERTER
VCC
+5V TO +10V
VOLTAGE DOUBLER
6
+5V
+5V
400kΩ
400kΩ
400kΩ
400kΩ
1.0μF
1.0μF
T1
T2
T4
T3
+
TOP VIEW
Figure 12. MAX234 Pin Configuration and Typical Operating Circuit
Maxim Integrated
21
MAX220–MAX249
MAX220–MAX249
+5V-Powered, Multichannel RS-232
Drivers/Receivers
1.0μF
+5V INPUT
GND
11
6
23
5
R2OUT
RS-232
INPUTS
TTL/CMOS
OUTPUTS
14 13
21
R5OUT
5kΩ
17 18
R4OUT
5kΩ
24
R3OUT
5kΩ
24
23
22
21
20
19
18
17
1
2
3
4
5
6
7
8
R3IN
R3OUT
T5IN
SHDNT2OUT
T1OUT
T3OUT
T4OUT
EN
T5OUT
R4IN
R4OUTT1IN
T2IN
R2OUT
R2IN
16
15
14
13
9
10
11
12
T4IN
T3IN
R5OUT
R5INVCC
GND
R1IN
R1OUT
DIP
MAX235
5kΩ
910
R1OUT R1IN
R2IN
R3IN
R4IN
R5IN
5kΩ
7
15
3
4
T2IN
T3OUT RS-232
OUTPUTS
TTL/CMOS
INPUTS
22 19T5IN T5OUT
+5V
16 1T4IN T4OUT
+5V
2
T3IN
+5V
+5V
8T1IN T1OUT
+5V
T2OUT
T1
T1
R2
R3
R4
R5
T2
T3
T5
T4
400kΩ
400kΩ
400kΩ
400kΩ
400kΩ
SHDN
EN
20
12
VCC
+
TOP VIEW
Figure 13. MAX235 Pin Configuration and Typical Operating Circuit
22
Maxim Integrated
MAX220–MAX249
MAX220–MAX249
+5V-Powered, Multichannel RS-232
Drivers/Receivers
GND
8
23
R2OUT RS-232
INPUTS
TTL/CMOS
OUTPUTS
17 16
21
R3OUT
R2IN
R3IN
5kΩ
5kΩ
54
R1OUT R1IN
5kΩ
RS-232
OUTPUTS
TTL/CMOS
INPUTS
R1
R2
R3
2
7T1IN T1OUT
+5V
T1
400kΩ
63
T2IN
+5V
T2OUT
T2
400kΩ
18 T3OUT 1
T3IN
+5V
T3
400kΩ
19 24
T4IN T4OUT
+5V
T4
400kΩ
SHDN
EN
20
11
C1+
C1-
1.0μF
10
12
13
14
15
+5V INPUT
C2+
C2-
VCC
+5V TO +10V
VOLTAGE DOUBLER
91.0μF
1.0μF
+10V TO -10V
VOLTAGE INVERTER
22
24
23
22
21
20
19
18
17
1
2
3
4
5
6
7
8
T4OUT
R2IN
R2OUT
SHDNR1IN
T2OUT
T1OUT
T3OUT
T4IN
T3IN
R3OUTGND
T1IN
T2IN
R1OUT
16
15
14
13
9
10
11
12
R3IN
V-
C2-
C2+C1-
V+
C1+
VCC
DIP/SO
MAX236 EN
1.0μF
1.0μF
TOP VIEW
V+
V-
+
Figure 14. MAX236 Pin Configuration and Typical Operating Circuit
Maxim Integrated
23
MAX220–MAX249
MAX220–MAX249
+5V-Powered, Multichannel RS-232
Drivers/Receivers
GND
8
23
R2OUT RS-232
INPUTS
TTL/CMOS
OUTPUTS
17 16
R3OUT
R2IN
R3IN
5kΩ
5kΩ
54
R1OUT R1IN
5kΩ
RS-232
OUTPUTS
TTL/CMOS
INPUTS
R1
R2
R3
2
7T1IN T1OUT
+5V
T1
400kΩ
63
T2IN
+5V
T2OUT
T2
400kΩ
18 T3OUT 1
T3IN
+5V
T3
400kΩ
21 20
T5IN T5OUT
+5V
T5
400kΩ
11
C1+
C1-
1.0μF
10
12
13
14
15
+5V INPUT
C2+
C2-
VCC
+5V TO +10V
VOLTAGE DOUBLER
91.0μF
1.0μF
+10V TO -10V
VOLTAGE INVERTER
22
24
23
22
21
20
19
18
17
1
2
3
4
5
6
7
8
T4OUT
R2IN
R2OUT
T5INR1IN
T2OUT
T1OUT
T3OUT
T4IN
T3IN
R3OUTGND
T1IN
T2IN
R1OUT
16
15
14
13
9
10
11
12
R3IN
V-
C2-
C2+C1-
V+
C1+
VCC
DIP/SO
MAX237 T5OUT
1.0μF
1.0μF
19 24
T4IN T4OUT
+5V
T4
400kΩ
V+
V-
+
TOP VIEW
Figure 15. MAX237 Pin Configuration and Typical Operating Circuit
24
Maxim Integrated
MAX220–MAX249
MAX220–MAX249
+5V-Powered, Multichannel RS-232
Drivers/Receivers
GND
8
3
R2OUT
22 23
R3OUT
R2IN
R3IN
5kΩ
5kΩ
67
R1OUT R1IN
5kΩ
RS-232
OUTPUTS
TTL/CMOS
INPUTS
RS-232
INPUTS
TTL/CMOS
OUTPUTS
R1
R2
R3
17 16
R4OUT R4IN
5kΩ
R4
2
5T1IN T1OUT
+5V
400kΩ
+5V
18 1
T2IN T2OUT
T2
400kΩ
19 T3OUT 24
T3IN
+5V
T3
400kΩ
11
C1+
C1-
1.0μF
10
12
13
14
15
+5V INPUT
C2+
C2-
VCC
+5V TO +10V
VOLTAGE DOUBLER
91.0μF
1.0μF
+10V TO -10V
VOLTAGE INVERTER
4
1.0μF
1.0μF
21 20
T4IN T4OUT
+5V
T4
400kΩ
T1
24
23
22
21
20
19
18
17
1
2
3
4
5
6
7
8
T3OUT
R3IN
R3OUT
T4INR2OUT
R2IN
T1OUT
T2OUT
TOP VIEW
T3IN
T2IN
R4OUTGND
R1IN
R1OUT
T1IN
16
15
14
13
9
10
11
12
R4IN
V-
C2-
C2+C1-
V+
C1+
VCC
DIP/SO
MAX238 T4OUT
+
V+
V-
Figure 16. MAX238 Pin Configuration and Typical Operating Circuit
Maxim Integrated
25
MAX220–MAX249
MAX220–MAX249
+5V-Powered, Multichannel RS-232
Drivers/Receivers
GND
3
18
R3OUT
12
R4OUT
R3IN
R4IN
5kΩ
5kΩ
22 21
R2OUT R2IN
5kΩ
RS-232
OUTPUTS
TTL/CMOS
INPUTS
RS-232
INPUTS
TTL/CMOS
OUTPUTS
R2
12
R1OUT R1IN
5kΩ
R1
R3
R4
10 9
R5OUT R5IN
5kΩ
R5
19
24 T1IN T1OUT
+5V
400kΩ
+5V
23 20
T2IN T2OUT
T2
400kΩ
16 T3OUT 13
T3IN
+5V
T3
400kΩ
C1+
C1-
1.0μF
6VCC 8
+5V INPUT
45
1.0μF
+10V TO -10V
VOLTAGE INVERTER
17
1.0μF
T1
24
23
22
21
20
19
18
17
1
2
3
4
5
6
7
8
T1IN
T2IN
R2OUT
R2INVCC
GND
R1IN
R1OUT
T1OUT
R3IN
R3OUTV-
C-
C+
V+
16
15
14
13
9
10
11
12
T3IN
N.C.
EN
T3OUTR4IN
R4OUT
R5OUT
R5IN
DIP/SO
MAX239 T2OUT
+7.5V TO +13.2V
INPUT
7
V+
11
EN
14 15
N.C.
V-
+
TOP VIEW
Figure 17. MAX239 Pin Configuration and Typical Operating Circuit
26
Maxim Integrated
MAX220–MAX249
MAX220–MAX249
+5V-Powered, Multichannel RS-232
Drivers/Receivers
GND
18
4R3OUT
40
R4OUT
R3IN
R4IN
5kΩ
5kΩ
13 10
R2OUT R2IN
5kΩ
RS-232
INPUTS
TTL/CMOS
OUTPUTS
RS-232
OUTPUTS
TTL/CMOS
INPUTS
R2
16 17
R1OUT R1IN
5kΩ
R1
R3
R4
36 35
R5OUT R5IN
5kΩ
R5
7
15 T1IN T1OUT
+5V
400kΩ
+5V
14 8
T2IN T2OUT
T2
400kΩ
37 T3OUT 6
T3IN
+5V
T3
400kΩ
C1+
C1-
1.0μF
25 VCC
+5V INPUT
19
30
1.0μF
26
1.0μF
+5V TO +10V
VOLTAGE DOUBLER
3
1.0μF
T1
+5V
241
T5IN T5OUT
T5
400kΩ
5
38 T4IN T4OUT
+5V 400kΩ
T4
27
C2+
C2-
28
1.0μF29
+5V TO -10V
VOLTAGE INVERTER
V+
39
EN
42 43
Plastic FP
MAX240
SHDN
EN
T5OUT
R4IN
R4OUT
R5OUT
R5IN
N.C.
N.C.
T3IN
T4IN
R2OUT
T2IN
T1IN
R1OUT
R1IN
N.C.
N.C.
N.C.
N.C.
VCC
GND
R2IN
N.C.
T4OUT
T2OUT
T1OUT
T3OUT
N.C.
R3IN
R3OUT
N.C.
T5IN
N.C.
C1+
C2
V+
C1-
C2+
N.C.
V-
N.C.
N.C.
N.C.
33
32
31
30
29
28
27
26
25
24
23
34
35
36
37
38
39
40
41
42
43
44
1
2
3
4
5
6
7
8
9
10
11
22
21
20
19
18
17
16
15
14
13
12
SHDN
TOP VIEW
V-
+
Figure 18. MAX240 Pin Configuration and Typical Operating Circuit
Maxim Integrated
27
MAX220–MAX249
MAX220–MAX249
+5V-Powered, Multichannel RS-232
Drivers/Receivers
V+
V-
2+10V
C1+
C1-
1
3
4
5
11
10
12
9
6
14
7
13
8
T1IN
R1OUT
T2IN
R2OUT
T1OUT
R1IN
T2OUT
R2IN
+5V INPUT
C2+
C2-
-10V
RS-232
OUTPUTS
RS-232
INPUTS
TTL/CMOS
INPUTS
TTL/CMOS
OUTPUTS
GND
15
5kΩ
5kΩ
400kΩ
400kΩ
+5V
+5V
+10V TO -10V
VOLTAGE INVERTER
+5V TO +10V
VOLTAGE DOUBLER
16
16
15
14
13
12
11
10
9
1
2
3
4
5
6
7
8
C1+ VCC
GND
T1OUT
R1IN
R1OUT
T1IN
T2IN
R2OUT
MAX243
DIP/SO
V+
C1-
V-
C2+
C2-
T2OUT
R2IN
0.1μF
0.1μF
0.1μF
0.1μF
0.1μF
RECEIVER INPUT
≤ -3V
OPEN
≥ +3V
R1 OUTPUT
HIGH
HIGH
LOW
R2 OUTPUT
HIGH
LOW
LOW
TOP VIEW
VCC
+
Figure 19. MAX243 Pin Configuration and Typical Operating Circuit
28
Maxim Integrated
MAX220–MAX249
MAX220–MAX249
+5V-Powered, Multichannel RS-232
Drivers/Receivers
400kΩ
+10V TO -10V VOLTAGE INVERTER
+5V TO +10V VOLTAGE DOUBLER
VCC
400kΩ
400kΩ
GND
+5V +5V
+5V +5V
+5V
25
24
23
21 20
2
1μF
1μF
1μF1μF
1μF
16
3
17
4
18
5kΩ
5kΩ
5kΩ
5kΩ
5kΩ
5kΩ
5kΩ
5kΩ
5kΩ
5kΩ
C2-
C2+
C1-
C1+
TA2OUT
TA2IN
TA3OUT
TA3IN
TA4OUT
TA4IN
9 RA1IN
10 RA1OUT
8 RA2IN
11 RA2OUT
7 RA3IN
12 RA3OUT
6 RA4IN
13 RA4OUT
5 RA5IN
14
19
RA5OUT
26
22
43
29
42
28
41
27
36
35
37
34
38
33
39
32
40
31
V-
V+
TB2OUT
TB2IN
400kΩ
2
15
TA1OUT
TA1IN
44
30
TB1OUT
TB1IN
TB3OUT
TB3IN
TB4OUT
TB4IN
RB1IN
RB1OUT
RB2IN
RB2OUT
RB3IN
RB3OUT
RB4IN
RB4OUT
RB5IN
RB5OUT
MAX249 FUNCTIONAL DESCRIPTION
10 RECEIVERS
5 A-SIDE RECEIVERS
5 B-SIDE RECEIVERS
8 TRANSMITTERS
4 A-SIDE TRANSMITTERS
4 B-SIDE TRANSMITTERS
NO CONTROL PINS
441234404142
43
5
21 24 26
25 27 28
22 2319 20
8
9
10
11
12
13
14
15
16
17 29
30
31
32
33
34
35
36
37
38
TA3IN
VCC
RA5IN
MAX244
PLCC
TOP VIEW
TA4OUT
TA3OUT
TA2OUT
TA1OUT
TB1OUT
TB2OUT
TB3OUT
TB4OUT
RB5IN
GND
V+
C1+
C2+
C1-
V-
C2-
TB3IN
TB4IN
RB3IN
RB2IN
RB1IN
RB1OUT
RB2OUT
RB3OUT
RB4OUT
RB5OUT
TB1IN
TB2IN
TA2IN
TA1IN
RA5OUT
RA4OUT
RA3OUT
RA2OUT
RA1OUT
RA1IN
RA2IN
739 RB4IN
RA3IN
6
18
RA4INTA4IN
+5V +5V
+5V +5V
+
Figure 20. MAX244 Pin Configuration and Typical Operating Circuit
Maxim Integrated
29
MAX220–MAX249
MAX220–MAX249
+5V-Powered, Multichannel RS-232
Drivers/Receivers
400kΩ
VCC
400kΩ
400kΩ
GND
+5V +5V
+5V +5V
+5V
40
17
1μF
3
18
4
19
5
5kΩ
5kΩ
5kΩ
5kΩ
5kΩ
5kΩ
5kΩ
5kΩ
5kΩ
5kΩ
TA2OUT
TA2IN
TA3OUT
TA3IN
TA4OUT
TA4IN
1
11 RA1IN
10 RA1OUT
12 RA2IN
9 RA2OUT
13 RA3IN
8 RA3OUT
14 RA4IN
7 RA4OUT
15 RA5IN
6
20
RA5OUT
23
37
22
36
21
35
29
30
28
31
27
32
26
33
25
34
TB2OUT
TB2IN
TB3OUT
TB3IN
TB4OUT
TB4IN
RB1IN
RB1OUT
RB2IN
RB2OUT
RB3IN
RB3OUT
RB4IN
RB4OUT
RB5IN
RB5OUT
+5V +5V
400kΩ
16
2
TA1OUT
TA1IN
24
38
TB1OUT
TB1IN
+5V +5V
40 VCC
ENT
TB1IN
TB2IN
TB3IN
TB4IN
RB5OUT
RB4OUT
RB3OUT
RB2OUT
RB1OUT
RB1IN
RB2IN
RB3IN
RB4IN
RB5IN
TB1OUT
TB2OUT
TB3OUT
TB4OUT
39
38
37
36
35
34
33
32
31
1
2
3
4
5
6
7
8
9
10
ENR
TA1IN
TA2IN
TA3IN
TA4IN
RA5OUT
RA4OUT
RA3OUT
RA2OUT
RA1OUT
RA1IN
RA2IN
RA3IN
RA4IN
RA5IN
TA1OUT
TA2OUT
TA3OUT
TA4OUT
GND
TOP VIEW
MAX245
30
29
28
27
26
25
24
23
22
21
11
12
13
14
15
16
17
18
19
DIP
20
MAX245 FUNCTIONAL DESCRIPTION
10 RECEIVERS
5 A-SIDE RECEIVERS (RA5 ALWAYS ACTIVE)
5 B-SIDE RECEIVERS (RB5 ALWAYS ACTIVE)
8 TRANSMITTTERS
4 A-SIDE TRANSMITTERS
2 CONTROL PINS
1 RECEIVER ENABLE (ENR)
1 TRANSMITTER ENABLE (ENT)
39
+
ENR ENT
Figure 21. MAX245 Pin Configuration and Typical Operating Circuit
30
Maxim Integrated
MAX220–MAX249
MAX220–MAX249
+5V-Powered, Multichannel RS-232
Drivers/Receivers
400kΩ
VCC
400kΩ
GND
+5V
+5V
+5V
+5V
+5V
40
16
1μF
2
18
4
TA1OUT
TA1IN
TA3OUT
TA3IN
20
24
38
22
36
139
TB1OUT
TB1IN
TB3OUT
TB3IN
400kΩ
+5V
17
3
TA2OUT
TA2IN
+5V
23
37
TB2OUT
TB2IN
400kΩ
+5V
19
5
TA4OUT
TA4IN
+5V
21
35
TB4OUT
TB4IN
5kΩ
5kΩ
5kΩ
5kΩ
5kΩ
5kΩ
5kΩ
5kΩ
5kΩ
5kΩ
11 RA1IN
10 RA1OUT
12 RA2IN
9 RA2OUT
13 RA3IN
8 RA3OUT
14 RA4IN
7 RA4OUT
15 RA5IN
6 RA5OUT
29
30
28
31
27
32
26
33
25
34
RB1IN
RB1OUT
RB2IN
RB2OUT
RB3IN
RB3OUT
RB4IN
RB4OUT
RB5IN
RB5OUT
40 VCC
ENB
TB1IN
TB2IN
TB3IN
TB4IN
RB5OUT
RB4OUT
RB3OUT
RB2OUT
RB1OUT
RB1IN
RB2IN
RB3IN
RB4IN
RB5IN
TB1OUT
TB2OUT
TB3OUT
TB4OUT
39
38
37
36
35
34
33
32
31
1
2
3
4
5
6
7
8
9
10
ENA
TA1IN
TA2IN
TA3IN
TA4IN
RA5OUT
RA4OUT
RA3OUT
RA2OUT
RA1OUT
RA1IN
RA2IN
RA3IN
RA4IN
RA5IN
TA1OUT
TA2OUT
TA3OUT
TA4OUT
GND
TOP VIEW
MAX246
30
29
28
27
26
25
24
23
22
21
11
12
13
14
15
16
17
18
19
DIP
20
MAX246 FUNCTIONAL DESCRIPTION
10 RECEIVERS
5 A-SIDE RECEIVERS (RA5 ALWAYS ACTIVE)
5 B-SIDE RECEIVERS (RB5 ALWAYS ACTIVE)
8 TRANSMITTERS
4 A-SIDE TRANSMITTERS
4 B-SIDE TRANSMITTERS
2 CONTROL PINS
ENABLE A-SIDE (ENA)
ENABLE B-SIDE (ENB)
ENA ENB
+
Figure 22. MAX246 Pin Configuration and Typical Operating Circuit
Maxim Integrated
31
MAX220–MAX249
MAX220–MAX249
+5V-Powered, Multichannel RS-232
Drivers/Receivers
400kΩ
VCC
400kΩ
GND
+5V
+5V
+5V
+5V
+5V
1
40
16
1μF
2
18
4
5kΩ
5kΩ
5kΩ
5kΩ
5kΩ
5kΩ
5kΩ
5kΩ
ENTA
TA1OUT
TA1IN
TA3OUT
TA3IN
6 RB5OUT
12 RA1IN
10 RA1OUT
13 RA2IN
9 RA2OUT
14 RA3IN
8 RA3OUT
15 RA4IN
7
20
RA4OUT
11
39
24
38
22
36
29
31
28
32
27
33
26
34
30ENRA
ENTB
TB1OUT
TB1IN
TB3OUT
TB3IN
RB1IN
5kΩ
25
RB5IN
RB1OUT
RB2IN
RB2OUT
RB3IN
RB3OUT
RB4IN
RB4OUT
ENRB
400kΩ
+5V
17
3
TA2OUT
TA2IN
+5V
23
37
TB2OUT
TB2IN
400kΩ
+5V
19
5
TA4OUT
TA4IN
+5V
21
35
TB4OUT
TB4IN
40 VCC
ENTB
TB1IN
TB2IN
TB3IN
TB4IN
RB4OUT
RB3OUT
RB2OUT
RB1OUT
RB1IN
RB2IN
RB3IN
RB4IN
RB5IN
TB1OUT
TB2OUT
TB3OUT
TB4OUT
39
38
37
36
35
34
33
32
31
1
2
3
4
5
6
7
8
9
10
ENTA
TA1IN
TA2IN
TA3IN
TA4IN
RB5OUT
RA4OUT
RA3OUT
RA2OUT
RA1OUT
RA1IN
RA2IN
RA3IN
RA4IN
TA1OUT
TA2OUT
TA3OUT
TA4OUT
GND
TOP VIEW
MAX247
30
29
28
27
26
25
24
23
22
21
11
12
13
14
15
16
17
18
19
DIP
20
ENRA ENRB
MAX247 FUNCTIONAL DESCRIPTION
9 RECEIVERS
4 A-SIDE RECEIVERS
5 B-SIDE RECEIVERS (RB5 ALWAYS ACTIVE)
8 TRANSMITTERS
4 A-SIDE TRANSMITTERS
4 B-SIDE TRANSMITTERS
4 CONTROL PINS
ENABLE RECEIVER A-SIDE (ENRA)
ENABLE RECEIVER B-SIDE (ENRB)
ENABLE RECEIVER A-SIDE (ENTA)
ENABLE RECEIVER B-SIDE (ENTB)
+
Figure 23. MAX247 Pin Configuration and Typical Operating Circuit
32
Maxim Integrated
MAX220–MAX249
MAX220–MAX249
+5V-Powered, Multichannel RS-232
Drivers/Receivers
400kΩ
+10V TO -10V VOLTAGE INVERTER
+5V TO +10V VOLTAGE DOUBLER
VCC
400kΩ
GND
+5V
+5V
+5V
+5V
+5V
18
25
24
23
21 20
1
1μF
1μF
1μF1μF
1μF
14
3
16
5kΩ
5kΩ
5kΩ
5kΩ
5kΩ
5kΩ
5kΩ
5kΩ
ENTA
C2-
C2+
C1-
C1+
TA1OUT
TA1IN
TA3OUT
TA3IN
8 RA1IN
10 RA1OUT
7 RA2IN
11 RA2OUT
6 RA3IN
12 RA3OUT
5 RA4IN
13
19
RA4OUT
9
27
26
22
44
31
42
29
37
35
38
34
39
33
40
32
36ENRA
ENTB
V-
V+
TB1OUT
TB1IN
TB3OUT
TB3IN
RB1IN
RB1OUT
RB2IN
RB2OUT
RB3IN
RB3OUT
RB4IN
RB4OUT
ENRB
400kΩ
+5V
2
15
TA2OUT
TA2IN
+5V
43
30
TB2OUT
TB2IN
400kΩ
+5V
4
17
TA4OUT
TA4IN
+5V
41
28
TB4OUT
TB4IN
441234404142
43
5
21 24 26
25 27 28
22 2319 20
8
9
10
11
12
13
14
15
16
17 29
30
31
32
33
34
35
36
37
38
TA4IN
VCC
RA4IN
MAX248
PLCC
TOP VIEW
TA4OUT
TA3OUT
TA2OUT
TA1OUT
TB1OUT
TB2OUT
TB3OUT
TA4OUT
RB4IN
GND
V+
C1+
C2+
C1-
V-
C2-
TB4IN
ENTB
RB2IN
RB1IN
RB1OUT
RB2OUT
RB3OUT
RB4OUT
TB1IN
TB2IN
TB3IN
TA3IN
TA2IN
TA1IN
RA4OUT
RA3OUT
RA2OUT
RA1OUT
ENRA
RA1IN
739 RB3IN
RA2IN
6
18
RA3IN
ENRB
ENTA
MAX248 FUNCTIONAL DESCRIPTION
8 RECEIVERS
4 A-SIDE RECEIVERS
4 B-SIDE RECEIVERS
8 TRANSMITTERS
4 A-SIDE TRANSMITTERS
4 B-SIDE TRANSMITTERS
4 CONTROL PINS
ENABLE RECEIVER A-SIDE (ENRA)
ENABLE RECEIVER B-SIDE (ENRB)
ENABLE RECEIVER A-SIDE (ENTA)
ENABLE RECEIVER B-SIDE (ENTB)
+
Figure 24. MAX248 Pin Configuration and Typical Operating Circuit
Maxim Integrated
33
MAX220–MAX249
MAX220–MAX249
+5V-Powered, Multichannel RS-232
Drivers/Receivers
400kΩ
+10V TO -10V VOLTAGE INVERTER
+5V TO +10V VOLTAGE DOUBLER
VCC
400kΩ
400kΩ
GND
+5V
+5V
+5V
+5V
+5V
+5V
+5V
18
25
24
23
21 20
1
1μF
1μF
1μF1μF
15
2
16
3
17
5kΩ
5kΩ
5kΩ
5kΩ
5kΩ
5kΩ
5kΩ
5kΩ
5kΩ
5kΩ
ENTA
C2-
C2+
C1-
C1+
TA1OUT
TA1IN
TA2OUT
TA2IN
TA3OUT
TA3IN
8 RA1IN
10 RA1OUT
7 RA2IN
11 RA2OUT
6 RA3IN
12 RA3OUT
5 RA4IN
13 RA4OUT
4 RA5IN
14
19
RA5OUT
9
27
26
22
44
30
43
29
42
28
37
35
38
34
39
33
40
32
41
31
36ENRA
ENTB
V-
V+
TB1OUT
TB1IN
TB2OUT
TB2IN
TB3OUT
TB3IN
RB1IN
RB1OUT
RB2IN
RB2OUT
RB3IN
RB3OUT
RB4IN
RB4OUT
RB5IN
RB5OUT
ENRB
441234404142
43
5
21 24 26
25 27 28
22 2319 20
8
9
10
11
12
13
14
15
16
17 29
30
31
32
33
34
35
36
37
38
VCC
RA4IN
RA5IN
MAX249
PLCC
TOP VIEW
TA3OUT
TA2OUT
TA1OUT
TB1OUT
TB2OUT
TB3OUT
RB4IN
RB5IN
GND
V+
C1+
C2+
C1-
V-
C2-
TB3IN
ENTB
RB2IN
RB1IN
RB1OUT
MAX249 FUNCTIONAL DESCRIPTION
10 RECEIVERS
5 A-SIDE RECEIVERS
5 B-SIDE RECEIVERS
6 TRANSMITTERS
3 A-SIDE TRANSMITTERS
3 B-SIDE TRANSMITTERS
4 CONTROL PINS
ENABLE RECEIVER A-SIDE (ENRA)
ENABLE RECEIVER B-SIDE (ENRB)
ENABLE RECEIVER A-SIDE (ENTA)
ENABLE RECEIVER B-SIDE (ENTB)
RB2OUT
RB3OUT
RB4OUT
RB5OUT
TB1IN
TB2INTA3IN
TA2IN
TA1IN
RA4OUT
RA5OUT
RA3OUT
RA2OUT
RA1OUT
ENRA
RA1IN
739 RB3IN
RA2IN
6
18
RA3IN
ENRB
ENTA
1μF
+
Figure 25. MAX249 Pin Configuration and Typical Operating Circuit
34
Maxim Integrated
MAX220–MAX249
MAX220–MAX249
+5V-Powered, Multichannel RS-232
Drivers/Receivers
___________________________________________Ordering Information (continued)
PART
MAX222CPN+ 0°C to +70°C
TEMP RANGE PIN-PACKAGE PART TEMP RANGE PIN-PACKAGE
18 Plastic DIP
MAX222CWN+ 0°C to +70°C 18 Wide SO
MAX222C/D 0°C to +70°C Dice*
MAX222EPN+ -40°C to +85°C 18 Plastic DIP
MAX222EWN+ -40°C to +85°C 18 Wide SO
MAX222EJN -40°C to +85°C 18 CERDIP
MAX222MJN -55°C to +125°C 18 CERDIP
MAX223CAI+ 0°C to +70°C 28 SSOP
MAX223CWI+ 0°C to +70°C 28 Wide SO
MAX223C/D 0°C to +70°C Dice*
MAX223EAI+ -40°C to +85°C 28 SSOP
MAX223EWI+ -40°C to +85°C 28 Wide SO
MAX225CWI+ 0°C to +70°C 28 Wide SO
MAX225EWI+ -40°C to +85°C 28 Wide SO
MAX230CPP+ 0°C to +70°C 20 Plastic DIP
MAX230CWP+ 0°C to +70°C 20 Wide SO
MAX230C/D 0°C to +70°C Dice*
MAX230EPP+ -40°C to +85°C 20 Plastic DIP
MAX230EWP+ -40°C to +85°C 20 Wide SO
MAX230EJP -40°C to +85°C 20 CERDIP
MAX230MJP -55°C to +125°C 20 CERDIP
MAX231CPD+ 0°C to +70°C 14 Plastic DIP
MAX231CWE+ 0°C to +70°C 16 Wide SO
MAX231CJD 0°C to +70°C 14 CERDIP
MAX231C/D 0°C to +70°C Dice*
MAX231EPD+ -40°C to +85°C 14 Plastic DIP
MAX231EWE+ -40°C to +85°C 16 Wide SO
MAX231EJD -40°C to +85°C 14 CERDIP
MAX231MJD -55°C to +125°C 14 CERDIP
MAX232CPE+ 0°C to +70°C 16 Plastic DIP
MAX232CSE+ 0°C to +70°C 16 Narrow SO
MAX232CWE+ 0°C to +70°C 16 Wide SO
MAX232C/D 0°C to +70°C Dice*
MAX232EPE+ -40°C to +85°C 16 Plastic DIP
MAX232ESE+ -40°C to +85°C 16 Narrow SO
MAX232EWE+ -40°C to +85°C 16 Wide SO
MAX232EJE -40°C to +85°C 16 CERDIP
MAX232MJE -55°C to +125°C 16 CERDIP
MAX232MLP+ -55°C to +125°C 20 LCC
MAX232ACPE+ 0°C to +70°C 16 Plastic DIP
MAX232ACSE+ 0°C to +70°C 16 Narrow SO
MAX232ACWE+ 0°C to +70°C 16 Wide SO
MAX232AC/D
MAX232AEPE+ -40°C to +85°C 16 Plastic DIP
MAX232AESE+
0°C to +70°C Dice*
-40°C to +85°C 16 Narrow SO
MAX232AEWE+ -40°C to +85°C 16 Wide SO
MAX232AEJE -40°C to +85°C 16 CERDIP
MAX232AMJE -55°C to +125°C 16 CERDIP
MAX232AMLP+ -55°C to +125°C 20 LCC
MAX233CPP+ 0°C to +70°C 20 Plastic DIP
MAX233EPP+ -40°C to +85°C 20 Plastic DIP
MAX233ACPP+ 0°C to +70°C 20 Plastic DIP
MAX233ACWP+ 0°C to +70°C 20 Wide SO
MAX233AEPP+ -40°C to +85°C 20 Plastic DIP
MAX233AEWP+ -40°C to +85°C 20 Wide SO
MAX234CPE+ 0°C to +70°C 16 Plastic DIP
MAX234CWE+ 0°C to +70°C 16 Wide SO
MAX234C/D 0°C to +70°C Dice*
MAX234EPE+ -40°C to +85°C 16 Plastic DIP
MAX234EWE+ -40°C to +85°C 16 Wide SO
MAX234EJE -40°C to +85°C 16 CERDIP
MAX234MJE -55°C to +125°C 16 CERDIP
MAX235CPG+ 0°C to +70°C 24 Wide Plastic DIP
MAX235EPG+ -40°C to +85°C 24 Wide Plastic DIP
MAX235EDG -40°C to +85°C 24 Ceramic SB
MAX235MDG -55°C to +125°C 24 Ceramic SB
MAX236CNG+ 0°C to +70°C 24 Narrow Plastic DIP
MAX236CWG+ 0°C to +70°C 24 Wide SO
MAX236C/D 0°C to +70°C Dice*
MAX236ENG+ -40°C to +85°C 24 Narrow Plastic DIP
MAX236EWG+ -40°C to +85°C 24 Wide SO
MAX236ERG -40°C to +85°C 24 Narrow CERDIP
MAX236MRG -55°C to +125°C 24 Narrow CERDIP
MAX237CNG+ 0°C to +70°C 24 Narrow Plastic DIP
MAX237CWG+ 0°C to +70°C 24 Wide SO
MAX237C/D 0°C to +70°C Dice*
MAX237ENG+ -40°C to +85°C 24 Narrow Plastic DIP
MAX237EWG+ -40°C to +85°C 24 Wide SO
MAX237ERG -40°C to +85°C 24 Narrow CERDIP
MAX237MRG -55°C to +125°C 24 Narrow CERDIP
MAX238CNG+ 0°C to +70°C 24 Narrow Plastic DIP
MAX238CWG+ 0°C to +70°C 24 Wide SO
MAX238C/D 0°C to +70°C Dice*
+
Denotes a lead(Pb)-free/RoHS-compliant package.
*
Contact factory for dice specifications.
Maxim Integrated
35
MAX220–MAX249
MAX220–MAX249
+5V-Powered, Multichannel RS-232
Drivers/Receivers
MAX238ENG+ -40°C to +85°C 24 Narrow Plastic DIP
___________________________________________Ordering Information (continued)
18 CERDIP-55°C to +125°CMAX242MJN
18 CERDIP-40°C to +85°CMAX242EJN
18 Wide SO-40°C to +85°CMAX242EWN+
18 Plastic DIP-40°C to +85°CMAX242EPN+
Dice*0°C to +70°CMAX242C/D
18 Wide SO0°C to +70°CMAX242CWN+
18 Plastic DIP0°C to +70°CMAX242CPN+
20 SSOP0°C to +70°C
MAX242CAP+
28 Wide SO-40°C to +85°CMAX241EWI+
28 SSOP-40°C to +85°CMAX241EAI+
Dice*0°C to +70°CMAX241C/D
28 Wide SO0°C to +70°CMAX241CWI+
28 SSOP0°C to +70°C
MAX241CAI+
Dice*0°C to +70°CMAX240C/D
44 Plastic FP0°C to +70°C
MAX240CMH+
24 Narrow CERDIP-55°C to +125°CMAX239MRG
24 Narrow CERDIP-40°C to +85°CMAX239ERG
24 Wide SO-40°C to +85°CMAX239EWG+
24 Narrow Plastic DIP-40°C to +85°CMAX239ENG+
Dice*0°C to +70°CMAX239C/D
24 Wide SO0°C to +70°CMAX239CWG+
24 Narrow Plastic DIP0°C to +70°C
MAX239CNG+
24 Narrow CERDIP-55°C to +125°C
24 Wide SO
PIN-PACKAGETEMP RANGE
-40°C to +85°C
MAX238MRG
24 Narrow CERDIP-40°C to +85°CMAX238ERG
MAX238EWG+
PART PIN-PACKAGETEMP RANGEPART
44 PLCC-40°C to +85°CMAX249EQH+
44 PLCC0°C to +70°C
MAX249CQH+
44 PLCC-40°C to +85°CMAX248EQH+
Dice*0°C to +70°CMAX248C/D
44 PLCC0°C to +70°C
MAX248CQH+
40 Plastic DIP-40°C to +85°CMAX247EPL+
Dice*0°C to +70°CMAX247C/D
40 Plastic DIP0°C to +70°C
MAX247CPL+
40 Plastic DIP-40°C to +85°CMAX246EPL+
Dice*0°C to +70°CMAX246C/D
40 Plastic DIP0°C to +70°C
MAX246CPL+
40 Plastic DIP-40°C to +85°CMAX245EPL+
Dice*0°C to +70°CMAX245C/D
40 Plastic DIP0°C to +70°C
MAX245CPL+
44 PLCC-40°C to +85°CMAX244EQH+
Dice*0°C to +70°CMAX244C/D
44 PLCC0°C to +70°C
MAX244CQH+
16 CERDIP-55°C to +125°CMAX243MJE
16 CERDIP-40°C to +85°CMAX243EJE
16 Wide SO-40°C to +85°CMAX243EWE+
16 Narrow SO-40°C to +85°CMAX243ESE+
16 Plastic DIP-40°C to +85°CMAX243EPE+
Dice*0°C to +70°CMAX243C/D
16 Wide SO0°C to +70°C
16 Plastic DIP0°C to +70°C
MAX243CWE+
16 Narrow SO0°C to +70°CMAX243CSE+
MAX243CPE+
+
Denotes a lead(Pb)-free/RoHS-compliant package.
*
Contact factory for dice specifications.
36
Maxim Integrated
MAX220–MAX249
MAX220–MAX249
+5V-Powered, Multichannel RS-232
Drivers/Receivers
Package Information
For the latest package outline information and land patterns, go to www.maxim-ic.com/packages. Note that a “+”, “#”, or “-” in
the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to
the package regardless of RoHS status.
PACKAGE TYPE PACKAGE CODE OUTLINE NO. LAND PATTERN NO.
14 PDIP P14+3
21-0043
—
16 PDIP P16+1
16 PDIP P16+2
16 PDIP P16+3
18 PDIP P18+5
20 PDIP P20+3
20 PDIP P20M+1
24 PDIP N24+3
24 PDIP P24M+1
21-0044
28 PDIP P28+2
40 PDIP P40+1
40 PDIP P40M+2
14 CERDIP J14-3
21-0045
16 CERDIP J16-3
18 CERDIP J18-2
20 CERDIP J20-2
24 CERDIP R24-4
16 SO(N) S16+3 21-0041 90-0097
16 SO(N) S16+5
16 SO(W) W16+1
21-0042
90-0107
16 SO(W) W16+2
16 SO(W) W16+3
18 SO(W) W18+1 90-0181
20 SO(W) W20+3 90-0108
20 SO(W) W20M+1
24 SO(W) W24+2 90-0182
28 SO(W) W28+1
90-0109
28 SO(W) W28+2
28 SO(W) W28M+1
20 LCC L20+3 21-0658 90-0177
20 SSOP A20+1
21-0056
90-0094
24 SSOP A24+2 90-0110
28 SSOP A28+1 90-0095
16 TSSOP U16+1 90-0117
16 FPCK F16-3 21-0013 —
44 MQFP M44+5 21-0826 90-0169
44 PLCC Q44+1 21-0049 90-0236
44 PLCC Q44+2
Maxim Integrated
37
MAX220–MAX249
MAX220–MAX249
+5V-Powered, Multichannel RS-232
Drivers/Receivers
Revision History
REVISION
NUMBER
REVISION
DATE DESCRIPTION PAGES
CHANGED
15 1/06
Added part information to the lead temperature in the Absolute Maximum Ratings
sections 2, 5, 8
16 7/10
Changed multiple packages to lead-free versions; updated/added notes 3, 4, 5, 7,
and 8 to the Electrical Characteristics table; removed incorrect subscripting from all
pin names in the Electrical Characteristics table and Pin Configurations
1, 2–9, 17–36
MAX220–MAX249
38 Maxim Integrated 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied.
Maxim reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical
Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
© 2010 Maxim Integrated The Maxim logo and Maxim Integrated are trademarks of Maxim Integrated Products, Inc.
MAX220–MAX249
