High - Q NP0 Chip Capacitors Features * Capacitance available from 0.2 pF to 1000 pF. * Available in 0402, 0603, 0805 & 1210 sizes. * Nickel Barrier / Tinned Termination. Characteristics Typical Series Resonant Frequency 0% 30ppm /C, -55C to 125C Dissipation Factor: .0002 (0.02%) max, 25C Quality Factor: Q > 5,000 @ 1MHz Ageing: None Insulation Resistance: 1,000 GW @ 25C, 50 mA max 125C IR is 10% of 25C, 50 mA max Dielectric Strength: 2.5 x WVDC Min., 25C, 50 mA max Test Parameters: 1MHz 50kHz, 1.0 0.2 VRMS, 25C 10 Frequency (GHz) Temperature Coefficient: 0402 0603 0805 1210 1 0.1 1 10 100 1000 Capacitance (pF) RF Performance Characteristics 0 Maximum ESR 0402, 0603 & 0805 Maximum ESR 0.25 0.25 2.7pF 0402 5.6pF 10pF 47pF 100pF 470pF 300 500 800 1000 0.10 0.04 100 Frequency (MHz) All components in this section are RoHS compliant per the EU directives and definitions. 26 47pF 0.20 10pF 0.10 0.05 100 10pF 100pf ESR (ohms) ESR (ohms) 0.20 5900 Shepherd Mountain Cove * Austin, TX 78730 Phone: 512 / 794-0081 * Fax: 512 / 794-0087 * Toll Free: 800 / 950-8365 e-mail: sales@venkel.com * www.venkel.com 300 Frequency (MHz) 500 800 1000 CASE SIZE Voltage 0402 25V 50V 0603 100V 250V 0805 100V 250V 1210 100V 200V 500V 0.2 pF 0.3 pF 0.4 pF 0.5 pF 0.6 pF 0.7 pF 0.8 pF 0.9 pF 1.0 pF 1.2 pF 1.5 pF 1.8 pF 2.2 pF 2.7 pF 3.3 pF 3.9 pF 4.7 pF 5.6 pF 6.8 pF 8.2 pF 9.1 pF 10 pF 12 pF 15 pF 18 pF 20 pF 22 pF 27 pF 33 pF 39 pF 47 pF 56 pF 68 pF 82 pF 100 pF 120 pF 150 pF 180 pF 220 pF 270 pF 330 pF 390 pF 470 pF 560 pF 680 pF 820 pF 1000 pF Voltage and Capacitance Range Above selection indicates standard product offering. Contact your sales representative for C/V requirements which may not be shown. Mechanical Characteristics L w PHYSICAL DIMENSIONS E/B 0402 LENGTH .010" (Millimeters) T .040 .060 .080 .125 (1.52) (2.03) (3.18) .020 .030 .050 .095 (0.510.1) (0.76) (1.27) (2.41) THICKNESS MAX Tin Plating Electrodes (Millimeters) Silver Base 08051210 (1.020.1) WIDTH .010" (Millimeters) 0603 .020 .035 .050 .060 (0.510.1) (0.90) (1.27) (1.52) ENDBAND MAX .010 .015 .020 .025 (Millimeters) (0.25) (0.38) (.508) (.640) Nickel Barrier Layer How To Order C0805 Series See Chart HQN201 --101 Dielectric Rated Voltage Capacitance Code 250 = 25V (pico - Farads) High - Q NP0 500 = 50v 1st 2 digits 101 = 100v are significant 151 = 150v followed by number 201 = 200v of zeroes. 251 = 250v 501 = 500v J N h E Tolerance Termination Marking Packaging Code: N = Nickel barrier, 6 = EIA "J" Code E = Embossed Tape **A = 0.05 pF Tinned Termination "Leave blank if P = Paper Tape *B = 0.1 pF G = Gold over No Marking" *C = 0.25 pF Nickel * 0402 size *D = 0.5 pF Standard termination finish for this product cannot be F = 1% is 100% matte Tin (Sn) marked. G = + 2% J = 5% K = 10% *For capacitance values below 10 pF only **For capacitance values of 1.8 pF or less. 5900 Shepherd Mountain Cove * Austin, TX 78730 Phone: 512 / 794-0081 * Fax: 512 / 794-0087 * Toll Free: 800 / 950-8365 e-mail: sales@venkel.com * www.venkel.com 27