Rev. 1.7 11/03 Copyright © 2003 by Silicon Laboratories
Mixed-Signal 32KB ISP FLASH MCU Family
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
JTAG
32KB
ISP FLASH 256/2304 B
SRAM SANITY
CONTROL
+
-
SAR
ADC
CLOCK
CIRCUIT
PGA
VREF
12-B it
DAC
AMUX
TEMP
SENSOR
VOLTAGE
COMPARATORS
ANALOG PERIPHERALS
Port 0Port 1
UART
SMBus
SPI Bus
PCA
Port 2Port 3
CROSSBAR
Timer 0
Timer 1
Timer 2
Timer 3
DIGITAL I/O
HIGH-SPEED CONTROLLER CORE
DEBUG
CIRCUITRY
21
INTERRUPTS
8051 CPU
(25MIPS)
12-B it
DAC
+
-
ANALOG PERIPHERALS
- SAR ADC
12-Bit (C8051F000/1/2, C8051F005/6/7)
10-bit (C8051F010/1/2, C8051F015/6/7)
1LSB INL; No Missing Codes
Programmable Throughput up to 100ksps
Up to 8 External Inputs; Programmable as Single-
Ended or Differential
Programmable Amplifier Gain: 16, 8, 4, 2, 1, 0.5
Data Dependent Windowed Interrupt Generator
Built-in Temperature Sensor ( 3C)
- Two 12-bit DACs
- Two Analog Comparators
Programmable Hysteresis Values
Configurable to Generate Interrupts or Reset
- Voltage Reference
2.4V; 15 ppm/C
Available on External Pin
- Precision VDD Monitor/Brown-out Detector
ON-CHIP JTAG DEBUG & BOUNDARY SCAN
- On-Chip Debug Circuitry Facilitates Full Speed, Non-
Intrusive In-System Debug (No Emulator Required!)
- Provides Breakpoints, Single Stepping, Watchpoints, Stack
Monitor
- Inspect/Modify Memory and Registers
- Superior Performance to Emulation Systems Using ICE-
Chips, Target Pods, and Sockets
- IEEE1149.1 Compliant Boundary Scan
- Low Cost Development Kit
HIGH SPEED 8051 C CORE
- Pipelined Instruction Architecture; Executes 70% of
Instruction Set in 1 or 2 System Clocks
- Up to 25MIPS Throughput with 25MHz Clock
- 21 Vectored Interrupt Sources
MEMORY
- 256 Bytes Internal Data RAM (F000/01/02/10/11/12)
- 2304 Bytes Internal Data RAM (F005/06/07/15/16/17)
- 32k Bytes FLASH; In-System Programmable in 512 byte
Sectors
DIGITAL PERIPHERALS
- 4 Byte-Wide Port I/O; All are 5V tolerant
- Hardware SMBusTM (I2CTM Compatible), SPITM, and UART
Serial Ports Available Concurrently
- Programmable 16-bit Counter/Timer Array with Five
Capture/Compare Modules
- Four General Purpose 16-bit Counter/Timers
- Dedicated Watch-Dog Timer
- Bi-directional Reset
CLOCK SOURCES
- Internal Programmable Oscillator: 2-to-16MHz
- External Oscillator: Crystal, RC,C, or Clock
- Can Switch Between Clock Sources on-the-fly; Useful in
Power Saving Modes
SUPPLY VOLTAGE ........................ 2.7V to 3.6V
- Typical Operating Current: 12.5mA @ 25MHz
- Multiple Power Saving Sleep and Shutdown Modes
64-Pin TQFP, 48-Pin TQFP, 32-Pin LQFP
Temperature Range: –40C to +85C
Rev. 1.7 2
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
TABLE OF CONTENTS
1. SYSTEM OVERVIEW ......................................................................................................... 8
Table 1.1. Product Selection Guide ..................................................................................................................... 8
Figure 1.1. C8051F000/05/10/15 Block Diagram ............................................................................................... 9
Figure 1.2. C8051F001/06/11/16 Block Diagram ............................................................................................. 10
Figure 1.3. C8051F002/07/12/17 Block Diagram ............................................................................................. 11
1.1. CIP-51TM CPU ......................................................................................................................................... 12
Figure 1.4. Comparison of Peak MCU Execution Speeds ................................................................................. 12
Figure 1.5. On-Board Clock and Reset .............................................................................................................. 13
1.2. On-Board Memory................................................................................................................................... 14
Figure 1.6. On-Board Memory Map .................................................................................................................. 14
1.3. JTAG Debug and Boundary Scan............................................................................................................ 15
Figure 1.7. Debug Environment Diagram ......................................................................................................... 15
1.4. Programmable Digital I/O and Crossbar ................................................................................................. 16
Figure 1.8. Digital Crossbar Diagram ................................................................................................................ 16
1.5. Programmable Counter Array .................................................................................................................. 17
Figure 1.9. PCA Block Diagram ....................................................................................................................... 17
1.6. Serial Ports ............................................................................................................................................... 17
1.7. Analog to Digital Converter .................................................................................................................... 18
Figure 1.10. ADC Diagram ............................................................................................................................... 18
1.8. Comparators and DACs ........................................................................................................................... 19
Figure 1.11. Comparator and DAC Diagram ..................................................................................................... 19
2. ABSOLUTE MAXIMUM RATINGS* .............................................................................. 20
3. GLOBAL DC ELECTRICAL CHARACTERISTICS .................................................... 20
4. PINOUT AND PACKAGE DEFINITIONS ..................................................................... 21
Table 4.1. Pin Definitions .................................................................................................................................. 21
Figure 4.1. TQFP-64 Pinout Diagram ............................................................................................................... 23
Figure 4.2. TQFP-64 Package Drawing ............................................................................................................ 24
Figure 4.3. TQFP-48 Pinout Diagram ............................................................................................................... 25
Figure 4.4. TQFP-48 Package Drawing ............................................................................................................ 26
Figure 4.5. LQFP-32 Pinout Diagram ............................................................................................................... 27
Figure 4.6. LQFP-32 Package Drawing ............................................................................................................ 28
5. ADC (12-Bit, C8051F000/1/2/5/6/7 Only) .......................................................................... 29
Figure 5.1. 12-Bit ADC Functional Block Diagram .......................................................................................... 29
5.1. Analog Multiplexer and PGA .................................................................................................................. 29
5.2. ADC Modes of Operation ........................................................................................................................ 30
Figure 5.2. 12-Bit ADC Track and Conversion Example Timing ..................................................................... 30
Figure 5.3. Temperature Sensor Transfer Function ........................................................................................... 31
Figure 5.4. AMX0CF: AMUX Configuration Register (C8051F00x) .............................................................. 31
Figure 5.5. AMX0SL: AMUX Channel Select Register (C8051F00x) ............................................................. 32
Figure 5.6. ADC0CF: ADC Configuration Register (C8051F00x) ................................................................... 33
Figure 5.7. ADC0CN: ADC Control Register (C8051F00x) ............................................................................ 34
Figure 5.8. ADC0H: ADC Data Word MSB Register (C8051F00x) ............................................................... 35
Figure 5.9. ADC0L: ADC Data Word LSB Register (C8051F00x) ................................................................. 3 5
5.3. ADC Programmable Window Detector ................................................................................................... 36
Figure 5.10. ADC0GTH: ADC Greater-Than Data High Byte Register (C8051F00x) .................................... 36
Figure 5.11. ADC0GTL: ADC Greater-Than Data Low Byte Register (C8051F00x) ..................................... 36
Figure 5.12. ADC0LTH: ADC Less-Than Data High Byte Register (C8051F00x) ......................................... 36
Figure 5.13. ADC0LTL: ADC Less-Than Data Low Byte Register (C8051F00x) ........................................... 36
Figure 5.14. 12-Bit ADC Window Interrupt Examples, Right Justified Data ................................................... 37
Figure 5.15. 12-Bit ADC Window Interrupt Examples, Left Justified Data ..................................................... 37
Figure 5.15. 12-Bit ADC Window Interrupt Examples, Left Justified Data ..................................................... 38
3 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Table 5.1. 12-Bit ADC Electrical Characteristics .............................................................................................. 38
Table 5.1. 12-Bit ADC Electrical Characteristics .............................................................................................. 39
6. ADC (10-Bit, C8051F010/1/2/5/6/7 Only) .......................................................................... 40
Figure 6.1. 10-Bit ADC Functional Block Diagram .......................................................................................... 40
6.1. Analog Multiplexer and PGA .................................................................................................................. 40
6.2. ADC Modes of Operation ........................................................................................................................ 41
Figure 6.2. 10-Bit ADC Track and Conversion Example Timing ..................................................................... 41
Figure 6.3. Temperature Sensor Transfer Function ........................................................................................... 42
Figure 6.4. AMX0CF: AMUX Configuration Register (C8051F01x) .............................................................. 42
Figure 6.5. AMX0SL: AMUX Channel Select Register (C8051F01x) ............................................................. 43
Figure 6.6. ADC0CF: ADC Configuration Register (C8051F01x) ................................................................... 44
Figure 6.7. ADC0CN: ADC Control Register (C8051F01x) ............................................................................ 45
Figure 6.8. ADC0H: ADC Data Word MSB Register (C8051F01x) ............................................................... 46
Figure 6.9. ADC0L: ADC Data Word LSB Register (C8051F01x) ................................................................. 4 6
6.3. ADC Programmable Window Detector ................................................................................................... 47
Figure 6.10. ADC0GTH: ADC Greater-Than Data High Byte Register (C8051F01x) .................................... 47
Figure 6.11. ADC0GTL: ADC Greater-Than Data Low Byte Register (C8051F01x) ..................................... 47
Figure 6.12. ADC0LTH: ADC Less-Than Data High Byte Register (C8051F01x) ......................................... 47
Figure 6.13. ADC0LTL: ADC Less-Than Data Low Byte Register (C8051F01x) ........................................... 47
Figure 6.14. 10-Bit ADC Window Interrupt Examples, Right Justified Data ................................................... 48
Figure 6.15. 10-Bit ADC Window Interrupt Examples, Left Justified Data ..................................................... 48
Figure 6.15. 10-Bit ADC Window Interrupt Examples, Left Justified Data ..................................................... 49
Table 6.1. 10-Bit ADC Electrical Characteristics .............................................................................................. 49
Table 6.1. 10-Bit ADC Electrical Characteristics .............................................................................................. 50
7. DACs, 12 BIT VOLTAGE MODE..................................................................................... 51
Figure 7.1. DAC Functional Block Diagram ...................................................................................................... 51
Figure 7.2. DAC0H: DAC0 High Byte Register ............................................................................................... 52
Figure 7.3. DAC0L: DAC0 Low Byte Register ................................................................................................ 52
Figure 7.4. DAC0CN: DAC0 Control Register ................................................................................................. 52
Figure 7.5. DAC1H: DAC1 High Byte Register ............................................................................................... 53
Figure 7.6. DAC1L: DAC1 Low Byte Register ................................................................................................ 53
Figure 7.7. DAC1CN: DAC1 Control Register ................................................................................................. 53
Table 7.1. DAC Electrical Characteristics ......................................................................................................... 54
8. COMPARATORS ............................................................................................................... 55
Figure 8.1. Comparator Functional Block Diagram .......................................................................................... 55
Figure 8.2. Comparator Hysteresis Plot ............................................................................................................. 56
Figure 8.3. CPT0CN: Comparator 0 Control Register ...................................................................................... 57
Figure 8.4. CPT1CN: Comparator 1 Control Register ...................................................................................... 58
Table 8.1. Comparator Electrical Characteristics .............................................................................................. 59
9. VOLTAGE REFERENCE ................................................................................................. 60
Figure 9.1. Voltage Reference Functional Block Diagram ............................................................................... 60
Figure 9.2. REF0CN: Reference Control Register ............................................................................................ 61
Table 9.1. Reference Electrical Characteristics ................................................................................................. 61
10. CIP-51 CPU .......................................................................................................................... 62
Figure 10.1. CIP-51 Block Diagram .................................................................................................................. 62
10.1. INSTRUCTION SET........................................................................................................................... 63
Table 10.1. CIP-51 Instruction Set Summary .................................................................................................... 65
10.2. MEMORY ORGANIZATION ............................................................................................................ 68
Figure 10.2. Memory Map ................................................................................................................................. 69
10.3. SPECIAL FUNCTION REGISTERS .................................................................................................. 70
Table 10.2. Special Function Register Memory Map ........................................................................................ 70
Table 10.3. Special Function Registers ............................................................................................................. 70
Figure 10.3. SP: Stack Pointer ........................................................................................................................... 74
Figure 10.4. DPL: Data Pointer Low Byte ........................................................................................................ 74
Rev. 1.7 4
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 10.5. DPH: Data Pointer High Byte ....................................................................................................... 74
Figure 10.6. PSW: Program Status Word ........................................................................................ .................. 75
Figure 10.7. ACC: Accumulator ........................................................................................................................ 76
Figure 10.8. B: B Register ................................................................................................................................. 76
10.4. INTERRUPT HANDLER ................................................................................................................... 77
Table 10.4. Interrupt Summary .......................................................................................................................... 78
Figure 10.9. IE: Interrupt Enable ....................................................................................................................... 79
Figure 10.10. IP: Interrupt Priority .................................................................................................................... 80
Figure 10.11. EIE1: Extended Interrupt Enable 1 ............................................................................................. 81
Figure 10.12. EIE2: Extended Interrupt Enable 2 ............................................................................................. 82
Figure 10.13. EIP1: Extended Interrupt Priority 1 ............................................................................................ 83
Figure 10.14. EIP2: Extended Interrupt Priority 2 ............................................................................................ 84
10.5. Power Management Modes ................................................................................................................. 85
Figure 10.15. PCON: Power Control Register .................................................................................................. 86
11. FLASH MEMORY .............................................................................................................. 87
11.1. Programming The Flash Memory ........................................................................................................ 87
Table 11.1. FLASH Memory Electrical Characteristics .................................................................................... 87
11.2. Non-volatile Data Storage ................................................................................................................... 88
11.3. Security Options .................................................................................................................................. 88
Figure 11.1. PSCTL: Program Store RW Control ............................................................................................. 88
Figure 11.2. Flash Program Memory Security Bytes ......................................................................................... 89
Figure 11.3. FLACL: Flash Access Limit (C8051F005/06/07/15/16/17 only) ................................................. 90
Figure 11.4. FLSCL: Flash Memory Timing Prescaler ..................................................................................... 91
12. EXTERNAL RAM (C8051F005/06/07/15/16/17) .............................................................. 92
Figure 12.1. EMI0CN: External Memory Interface Control ............................................................................. 92
13. RESET SOURCES .............................................................................................................. 93
Figure 13.1. Reset Sources Diagram ................................................................................................................. 93
13.1. Power-on Reset .................................................................................................................................... 94
13.2. Software Forced Reset ......................................................................................................................... 94
Figure 13.2. VDD Monitor Timing Diagram .................................................................................................... 94
13.3. Power-fail Reset................................................................................................................................... 94
13.4. External Reset ...................................................................................................................................... 95
13.5. Missing Clock Detector Reset ............................................................................................................. 95
13.6. Comparator 0 Reset ............................................................................................................................. 95
13.7. External CNVSTR Pin Reset ............................................................................................................... 95
13.8. Watchdog Timer Reset ........................................................................................................................ 95
Figure 13.3. WDTCN: Watchdog Timer Control Register ............................................................................... 96
Figure 13.4. RSTSRC: Reset Source Register ................................................................................................... 97
Table 13.1. Reset Electrical Characteristics ...................................................................................................... 98
14. OSCILLATOR .................................................................................................................... 99
Figure 14.1. Oscillator Diagram ........................................................................................................................ 99
Figure 14.2. OSCICN: Internal Oscillator Control Register ........................................................................... 100
Table 14.1. Internal Oscillator Electrical Characteristics ................................................................................ 100
Figure 14.3. OSCXCN: External Oscillator Control Register ......................................................................... 101
14.1. External Crystal Example .................................................................................................................. 102
14.2. External RC Example ........................................................................................................................ 102
14.3. External Capacitor Example .............................................................................................................. 102
15. PORT INPUT/OUTPUT ................................................................................................... 103
15.1. Priority Cross Bar Decoder ................................................................................................................ 103
15.2. Port I/O Initialization ......................................................................................................................... 103
Figure 15.1. Port I/O Functional Block Diagram ............................................................................................ 104
Figure 15.2. Port I/O Cell Block Diagram ....................................................................................................... 104
Table 15.1. Crossbar Priority Decode ............................................................................................................. 105
Figure 15.3. XBR0: Port I/O CrossBar Register 0 .......................................................................................... 106
5 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 15.4. XBR1: Port I/O CrossBar Register 1 .......................................................................................... 107
Figure 15.5. XBR2: Port I/O CrossBar Register 2 .......................................................................................... 108
15.3. General Purpose Port I/O ................................................................................................................... 109
15.4. Configuring Ports Which are not Pinned Out .................................................................................... 109
Figure 15.6. P0: Port0 Register ....................................................................................................................... 109
Figure 15.7. PRT0CF: Port0 Configuration Register ...................................................................................... 109
Figure 15.8. P1: Port1 Register ....................................................................................................................... 110
Figure 15.9. PRT1CF: Port1 Configuration Register ...................................................................................... 110
Figure 15.10. PRT1IF: Port1 Interrupt Flag Register ...................................................................................... 110
Figure 15.11. P2: Port2 Register ..................................................................................................................... 111
Figure 15.12. PRT2CF: Port2 Configuration Register .................................................................................... 111
Figure 15.13. P3: Port3 Register ..................................................................................................................... 112
Figure 15.14. PRT3CF: Port3 Configuration Register .................................................................................... 112
Table 15.2. Port I/O DC Electrical Characteristics .......................................................................................... 112
16. SMBus / I2C Bus ................................................................................................................ 113
Figure 16.1. SMBus Block Diagram ............................................................................................................... 113
Figure 16.2. Typical SMBus Configuration .................................................................................................... 114
16.1. Supporting Documents ...................................................................................................................... 114
16.2. Operation ........................................................................................................................................... 115
Figure 16.3. SMBus Transaction ..................................................................................................................... 115
16.3. Arbitration ......................................................................................................................................... 116
16.4. Clock Low Extension ........................................................................................................................ 116
16.5. Timeouts ............................................................................................................................................ 116
16.6. SMBus Special Function Registers .................................................................................................... 116
Figure 16.4. SMB0CN: SMBus Control Register ............................................................................................ 118
Figure 16.5. SMB0CR: SMBus Clock Rate Register ...................................................................................... 119
Figure 16.6. SMB0DAT: SMBus Data Register ............................................................................................. 120
Figure 16.7. SMB0ADR: SMBus Address Register ....................................................................................... 120
Figure 16.8. SMB0STA: SMBus Status Register ............................................................................................ 121
Table 16.1. SMBus Status Codes .................................................................................................................... 122
17. SERIAL PERIPHERAL INTERFACE BUS .................................................................. 123
Figure 17.1. SPI Block Diagram ..................................................................................................................... 123
Figure 17.2. Typical SPI Interconnection ........................................................................................................ 124
17.1. Signal Descriptions ............................................................................................................................ 124
17.2. Operation ........................................................................................................................................... 125
Figure 17.3. Full Duplex Operation ................................................................................................................. 125
17.3. Serial Clock Timing ........................................................................................................................... 126
Figure 17.4. Data/Clock Timing Diagram ....................................................................................................... 126
17.4. SPI Special Function Registers .......................................................................................................... 127
Figure 17.5. SPI0CFG: SPI Configuration Register ........................................................................................ 127
Figure 17.6. SPI0CN: SPI Control Register .................................................................................................... 128
Figure 17.7. SPI0CKR: SPI Clock Rate Register ............................................................................................ 129
Figure 17.8. SPI0DAT: SPI Data Register ...................................................................................................... 129
18. UART .................................................................................................................................. 130
Figure 18.1. UART Block Diagram ................................................................................................................ 130
18.1. UART Operational Modes ................................................................................................................. 131
Table 18.1. UART Modes ............................................................................................................................... 131
Figure 18.2. UART Mode 0 Interconnect ........................................................................................................ 131
Figure 18.3. UART Mode 0 Timing Diagram ................................................................................................. 131
Figure 18.4. UART Mode 1 Timing Diagram ................................................................................................. 132
Figure 18.5. UART Modes 1, 2, and 3 Interconnect Diagram ........................................................................ 133
Figure 18.6. UART Modes 2 and 3 Timing Diagram ...................................................................................... 134
18.2. Multiprocessor Communications ....................................................................................................... 135
Figure 18.7. UART Multi-Processor Mode Interconnect Diagram ................................................................. 135
Rev. 1.7 6
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Table 18.2. Oscillator Frequencies for Standard Baud Rates .......................................................................... 136
Figure 18.8. SBUF: Serial (UART) Data Buffer Register ............................................................................... 136
Figure 18.9. SCON: Serial Port Control Register ............................................................................................ 137
19. TIMERS ............................................................................................................................. 138
19.1. Timer 0 and Timer 1 .......................................................................................................................... 138
Figure 19.1. T0 Mode 0 Block Diagram.......................................................................................................... 139
Figure 19.2. T0 Mode 2 Block Diagram.......................................................................................................... 140
Figure 19.3. T0 Mode 3 Block Diagram.......................................................................................................... 141
Figure 19.4. TCON: Timer Control Register ................................................................................................... 142
Figure 19.5. TMOD: Timer Mode Register ..................................................................................................... 143
Figure 19.6. CKCON: Clock Control Register ................................................................................................ 144
Figure 19.7. TL0: Timer 0 Low Byte .............................................................................................................. 145
Figure 19.8. TL1: Timer 1 Low Byte .............................................................................................................. 145
Figure 19.9. TH0: Timer 0 High Byte ............................................................................................................. 145
Figure 19.10. TH1: Timer 1 High Byte ........................................................................................................... 145
19.2. Timer 2 .............................................................................................................................................. 146
Figure 19.11. T2 Mode 0 Block Diagram........................................................................................................ 147
Figure 19.12. T2 Mode 1 Block Diagram........................................................................................................ 148
Figure 19.13. T2 Mode 2 Block Diagram........................................................................................................ 149
Figure 19.14. T2CON: Timer 2 Control Register ............................................................................................ 150
Figure 19.15. RCAP2L: Timer 2 Capture Register Low Byte ........................................................................ 151
Figure 19.16. RCAP2H: Timer 2 Capture Register High Byte ....................................................................... 151
Figure 19.17. TL2: Timer 2 Low Byte ............................................................................................................ 151
Figure 19.18. TH2: Timer 2 High Byte ........................................................................................................... 151
19.3. Timer 3 .............................................................................................................................................. 152
Figure 19.19. Timer 3 Block Diagram ............................................................................................................. 152
Figure 19.20. TMR3CN: Timer 3 Control Register ........................................................................................ 152
Figure 19.21. TMR3RLL: Timer 3 Reload Register Low Byte ...................................................................... 153
Figure 19.22. TMR3RLH: Timer 3 Reload Register High Byte ..................................................................... 153
Figure 19.23. TMR3L: Timer 3 Low Byte ...................................................................................................... 153
Figure 19.24. TMR3H: Timer 3 High Byte ..................................................................................................... 153
20. PROGRAMMABLE COUNTER ARRAY ..................................................................... 154
Figure 20.1. PCA Block Diagram ................................................................................................................... 154
20.1. Capture/Compare Modules ................................................................................................................ 155
Table 20.1. PCA0CPM Register Settings for PCA Capture/Compare Modules ............................................. 155
Figure 20.2. PCA Interrupt Block Diagram ..................................................................................................... 155
Figure 20.3. PCA Capture Mode Diagram ...................................................................................................... 156
Figure 20.4. PCA Software Timer Mode Diagram .......................................................................................... 157
Figure 20.5. PCA High Speed Output Mode Diagram .................................................................................... 157
Figure 20.6. PCA PWM Mode Diagram ......................................................................................................... 158
20.2. PCA Counter/Timer ........................................................................................................................... 159
Table 20.2. PCA Timebase Input Options ....................................................................................................... 159
Figure 20.7. PCA Counter/Timer Block Diagram ........................................................................................... 159
20.3. Register Descriptions for PCA .......................................................................................................... 160
Figure 20.8. PCA0CN: PCA Control Register ................................................................................................. 160
Figure 20.9. PCA0MD: PCA Mode Register .................................................................................................. 161
Figure 20.10. PCA0CPMn: PCA Capture/Compare Registers ........................................................................ 162
Figure 20.11. PCA0L: PCA Counter/Timer Low Byte ................................................................................... 163
Figure 20.12. PCA0H: PCA Counter/Timer High Byte .................................................................................. 163
Figure 20.13. PCA0CPLn: PCA Capture Module Low Byte .......................................................................... 163
Figure 20.14. PCA0CPHn: PCA Capture Module High Byte ......................................................................... 163
21. JTAG (IEEE 1149.1) ......................................................................................................... 164
Figure 21.1. IR: JTAG Instruction Register .................................................................................................... 164
21.1. Boundary Scan ................................................................................................................................... 165
7 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Table 21.1. Boundary Data Register Bit Definitions ....................................................................................... 165
Figure 21.2. DEVICEID: JTAG Device ID Register ...................................................................................... 166
21.2. Flash Programming Commands ......................................................................................................... 167
Figure 21.3. FLASHCON: JTAG Flash Control Register ............................................................................... 168
Figure 21.4. FLASHADR: JTAG Flash Address Register .............................................................................. 168
Figure 21.5. FLASHDAT: JTAG Flash Data Register .................................................................................... 169
Figure 21.6. FLASHSCL: JTAG Flash Scale Register ................................................................................... 169
21.3. Debug Support ................................................................................................................................... 170
Rev. 1.7 8
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
1. SYSTEM OVERVIEW
The C8051F000 family are fully integrated mixed-signal System on a Chip MCUs with a true 12-bit multi-channel
ADC (F000/01/02/05/06/07), or a true 10-bit multi-channel ADC (F010/11/12/15/16/17). See the Product Selection
Guide in Table 1.1 for a quick reference of each MCUs’ feature set. Each has a programmable gain pre-amplifier,
two 12-bit DACs, two voltage comparators (except for the F002/07/12/17, which have one), a voltage reference,
and an 8051-compatible microcontroller core with 32kbytes of FLASH memory. There are also I2C/SMBus,
UART, and SPI serial interfaces implemented in hardware (not “bit-banged” in user software) as well as a
Programmable Counter/Timer Array (PCA) with five capture/compare modules. There are also 4 general-purpose
16-bit timers and 4 byte-wide general-purpose digital Port I/O. The C8051F000/01/02/10/11/12 have 256 bytes of
RAM and execute up to 20MIPS, while the C8051F005/06/07/15/16/17 have 2304 bytes of RAM and execute up to
25MIPS.
With an on-board VDD monitor, WDT, and clock oscillator, the MCUs are truly stand-alone System-on-a-Chip
solutions. Each MCU effectively configures and manages the analog and digital peripherals. The FLASH memory
can be reprogrammed even in-circuit, providing non-volatile data storage, and also allowing field upgrades of the
8051 firmware. Each MCU can also individually shut down any or all of the peripherals to conserve power.
On-board JTAG debug support allows non-intrusive (uses no on-chip resources), full speed, in-circuit debug using
the production MCU installed in the final application. This debug system supports inspection and modification of
memory and registers, setting breakpoints, watchpoints, single stepping, and run and halt commands. All analog
and digital peripherals are fully functional when using JTAG debug.
Each MCU is specified for 2.7V-to-3.6V operation over the industrial temperature range (-45C to +85C). The Port
I/Os, /RST, and JTAG pins are tolerant for input signals up to 5V. The C8051F000/05/10/15 are available in the
64-pin TQFP (see block diagram in Figure 1.1). The C8051F001/06/11/16 are available in the 48-pin TQFP (see
block diagram in Figure 1.2). The C8051F002/07/12/17 are available in the 32-pin LQFP (see block diagram in
Figure 1.3).
Table 1.1. Product Selection Guide
MIPS (Peak)
FLASH Memory
RAM
SMBus/I2C
SPI
UART
Timers (16-bit)
Programmable Counter Arr a y
Digital Port I/O’s
ADC Resolution (bits)
ADC Max Speed (ksps)
ADC Inputs
Voltage Reference
Temperature Sensor
DAC Resolution
DAC Out
p
uts
Voltage Comparators
Package
C8051F000 20 32k 256
4 32 12 100 8 12 2 2 64TQFP
C8051F001 20 32k 256
4 16 12 100 8 12 2 2 48TQFP
C8051F002 20 32k 256
4 8 12 100 4 12 2 1 32LQFP
C8051F005 25 32k 2304
4 32 12 100 8 12 2 2 64TQFP
C8051F006 25 32k 2304
4 16 12 100 8 12 2 2 48TQFP
C8051F007 25 32k 2304
4 8 12 100 4 12 2 1 32LQFP
C8051F010 20 32k 256
4 32 10 100 8 12 2 2 64TQFP
C8051F011 20 32k 256
4 16 10 100 8 12 2 2 48TQFP
C8051F012 20 32k 256
4 8 10 100 4 12 2 1 32LQFP
C8051F015 25 32k 2304
4 32 10 100 8 12 2 2 64TQFP
C8051F016 25 32k 2304
4 16 10 100 8 12 2 2 48TQFP
C8051F017 25 32k 2304
4 8 10 100 4 12 2 1 32LQFP
9 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 1.1. C8051F000/05/10/15 Block Diagram
Port 0
Latch
Port 1
Latch
JTAG
Logic
TCK
TMS
TDI
TDO
UART
SMBus
SPI Bus
PCA
32kbyte
FLASH
2048 byte
XRAM
(F005/15 only)
DAC0 DAC0
(12-Bit)
SFR Bus
Port 2
Latch
Port 3
Latch
8
0
5
1
C
o
r
e
Timers
0,1,2
Tim er 3
VREF
C
R
O
S
S
B
A
R
S
W
I
T
C
H
AV+
AV+
VDD
VDD
VDD
DGND
DGND
DGND
AGND
AGND
XTAL1
XTAL2
External
Oscillator
Circuit System Clock
Internal
Oscillator
Digital Power
Analog Power
D ebug HW
Boundary Scan
256 byte
RAM
VREF
VDD
Monitor
Reset
/RST
WDT
Rev. 1.7 10
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 1.2. C8051F001/06/11/16 Block Diagram
JTAG
Logic
TCK
TMS
TDI
TDO
32kbyte
FLASH
2048 byte
XRAM
(F006/16 only)
SFR Bus
8
0
5
1
C
o
r
e
AV+
AV+
VDD
VDD
DGND
DGND
DGND
DGND
AGND
AGND
XTAL1
XTAL2
External
Oscillator
Circuit System Clock
In te rn al
Oscillator
Digital Power
Analog Power
Debug HW
Bounda ry Scan
256 byte
RAM Port 0
Latch
Port 1
Latch
UART
SMBus
SPI Bus
PCA
Port 2
Latch
Port 3
Latch
Timers
0,1,2
Tim er 3
C
R
O
S
S
B
A
R
S
W
I
T
C
H
DAC0 DAC0
(12-Bit)
VREF VREF
VDD
Monitor
Reset
/RST
WDT
11 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 1.3. C8051F002/07/12/17 Block Diagram
JTAG
Logic
TCK
TMS
TDI
TDO
32kbyte
FLASH
2048 byte
XRAM
(F007/17 only)
SFR Bus
8
0
5
1
C
o
r
e
AV+
AV+
VDD
VDD
DGND
DGND
AGND
AGND
XTAL1
XTAL2
External
Oscillator
Circuit System Clock
In te rn a l
Oscillator
Digital Power
Analog Pow er
Debug HW
Boundary Scan
256 byte
RAM Port 0
Latch
Port 1
Latch
UART
SMBus
SPI Bus
PCA
Port 2
Latch
Port 3
Latch
Timers
0,1,2
Tim er 3
C
R
O
S
S
B
A
R
S
W
I
T
C
H
DAC0 DAC0
(12-Bit)
DAC
1
VREF VREF
VDD
Monitor
Reset
/RST
WDT
Rev. 1.7 12
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
1.1. CIP-51TM CPU
1.1.1. Fully 8051 Compatible
The C8051F000 family utilizes Silicon Laboratories’ proprietary CIP-51 microcontroller core. The CIP-51 is fully
compatible with the MCS-51TM instruction set. Standard 803x/805x assemblers and compilers can be used to
develop software. The core has all the peripherals included with a standard 8052, including four 16-bit
counter/timers, a full-duplex UART, 256 bytes of internal RAM space, 128 byte Special Function Register (SFR)
address space, and four byte-wide I/O Ports.
1.1.2. Improved Throughput
The CIP-51 employs a pipelined architecture that greatly increases its instruction throughput over the standard 8051
architecture. In a standard 8051, all instructions except for MUL and DIV take 12 or 24 system clock cycles to
execute with a maximum system clock of 12-to-24MHz. By contrast, the CIP-51 core executes 70% of its
instructions in one or two system clock cycles, with only four instructions taking more than four system clock
cycles.
The CIP-51 has a total of 109 instructions. The number of instructions versus the system clock cycles to execute
them is as follows:
Instructions 26 50 5 14 7 3 1 2 1
Clocks to Execute 1 2 2/3 3 3/4 4 4/5 5 8
With the CIP-51’s maximum system clock at 25MHz, it has a peak throughput of 25MIPS. Figure 1.4 shows a
comparison of peak throughputs of various 8-bit microcontroller cores with their maximum system clocks.
Figure 1.4. Comparison of Peak MCU Execution Speeds
5
10
15
20
ADuC812
8051
(16 M H z
clk)
Philips
80C51
(33 M H z
clk)
Microchip
PIC17C75x
(3 3MH z
clk)
Silicon Labs
CIP-51
(2 5MHz c lk)
MIPS
25
13 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
1.1.3. Additional Features
The C8051F000 MCU family has several key enhancements both inside and outside the CIP-51 core to improve its
overall performance and ease of use in the end applications.
The extended interrupt handler provides 21 interrupt sources into the CIP-51 (as opposed to 7 for the standard
8051), allowing the numerous analog and digital peripherals to interrupt the controller. An interrupt driven system
requires less intervention by the MCU, giving it more effective throughput. The extra interrupt sources are very
useful when building multi-tasking, real-time systems.
There are up to seven reset sources for the MCU: an on-board VDD monitor, a Watchdog Timer, a missing clock
detector, a voltage level detection from Comparator 0, a forced software reset, the CNVSTR pin, and the /RST pin.
The /RST pin is bi-directional, accommodating an external reset, or allowing the internally generated POR to be
output on the /RST pin. Each reset source except for the VDD monitor and Reset Input Pin may be disabled by the
user in software. The WDT may be permanently enabled in software after a power-on reset during MCU
initialization.
The MCU has an internal, stand alone clock generator which is used by default as the system clock after any reset.
If desired, the clock source may be switched on the fly to the external oscillator, which can use a crystal, ceramic
resonator, capacitor, RC, or external clock source to generate the system clock. This can be extremely useful in low
power applications, allowing the MCU to run from a slow (power saving) external crystal source, while periodically
switching to the fast (up to 16MHz) internal oscillator as needed.
Figure 1.5. On-Board Clock and Reset
WDT
XTAL1
XTAL2 OSC
Inte rn a l
Clock
Generator System
Clock CIP-51
Microcontroller
Core
M issing
Clock
Detector
(one-
shot)
WDT
Strobe
Software Reset
Extended Interrupt
Handler
Clock Select
/RST
+
-
VDD
Supply
Reset
Timeout (wired-OR)
System R eset
Supply
Monitor
PRE
Reset
Funnel
+
-
CP0+ Com parator 0
CP0-
(Port
I/O) Crossbar CNVSTR
(CNVSTR
rese t
enable)
(CP 0
rese t
enable)
EN
WDT
Enable
EN
MCD
Enable
Rev. 1.7 14
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
1.2. On-Board Memory
The CIP-51 has a standard 8051 program and data address configuration. It includes 256 bytes of data RAM, with
the upper 128 bytes dual-mapped. Indirect addressing accesses the upper 128 bytes of general purpose RAM, and
direct addressing accesses the 128 byte SFR address space. The lower 128 bytes of RAM are accessible via direct
and indirect addressing. The first 32 bytes are addressable as four banks of general-purpose registers, and the next
16 bytes can be byte addressable or bit addressable.
The CIP-51 in the C8051F005/06/07/15/16/17 MCUs additionally has a 2048 byte RAM block in the external data
memory address space. This 2048 byte block can be addressed over the entire 64k external data memory address
range (see Figure 1.6).
The MCU’s program memory consists of 32k + 128 bytes of FLASH. This memory may be reprogrammed in-
system in 512 byte sectors, and requires no special off-chip programming voltage. The 512 bytes from addresses
0x7E00 to 0x7FFF are reserved for factory use. There is also a single 128-byte sector at address 0x8000 to 0x807F,
which may be useful as a small table for software constants or as additional program space. See Figure 1.6 for the
MCU system memory map.
Figure 1.6. On-Board Memory Map
FLASH
(In-System
Program m able in 512
Byte Sectors)
PROGRAM M EMORY
0x0000
0x7FFF
(Direct and Indirect
Addressing)
0x00
0x7F
Upper 128 RA M
(Indirect Addressing
Only)
0x80
0xFF Special Function
Register's
(Direct Addressing O nly)
RESERVED
0x7E00
0x7DFF
128 Byte ISP FLASH
0x8000
0x807F
DATA MEMORY
G e n era l Pu rp os e
Registers
0x1F
0x20
0x2F Bit Addressable
Lower 128 RA M
(Direct and Indirect
Addressing)
0x30
INTERNAL DATA ADDRESS SPACE
EXTERNAL DATA ADDRESS SPACE
RA M - 2048 Bytes
(accessable using MOVX
instruction)
0x0000
0x07FF
(same 2048 byte RAM block )
0x0800
0x0FFF
(same 2048 byte RAM block )
0xF800
0xFFFF
The same 2048 byte R AM
block can be addressed on
2k boundaries throughout
the 64k External Data
Memory space.
(same 2048 byte RAM block )
0x1000
0x17FF
15 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
1.3. JTAG Debug and Boundary Scan
The C8051F000 family has on-chip JTAG and debug circuitry that provide non-intrusive, full speed, in-circuit
debug using the production part installed in the end application using the four-pin JTAG I/F. The JTAG port is
fully compliant to IEEE 1149.1, providing full boundary scan for test and manufacturing purposes.
Silicon Labs’ debug system supports inspection and modification of memory and registers, breakpoints,
watchpoints, a stack monitor, and single stepping. No additional target RAM, program memory, timers, or
communications channels are required. All the digital and analog peripherals are functional and work correctly
while debugging. All the peripherals (except for the ADC) are stalled when the MCU is halted, during single
stepping, or at a breakpoint in order to keep them in sync.
The C8051F000DK, C8051F005DK, C8051F010DK, and C8051F015DK are development kits with all the
hardware and software necessary to develop application code and perform in-circuit debug with the C8051F000/1/2,
F005/6/7, F010/1/2, and F015/6/7 MCUs respectively. The kit includes software with a developer’s studio and
debugger, an integrated 8051 assembler, and an RS-232 to JTAG protocol translator module referred to as the EC.
It also has a target application board with the associated MCU installed and a large prototyping area, plus the RS-
232 and JTAG cables, and wall-mount power supply. The Development Kit requires a Windows
95/98/NT/2000/XP computer with one available RS-232 serial port. As shown in Figure 1.7, the PC is connected
via RS-232 to the EC. A six-inch ribbon cable connects the EC to the user’s application board, picking up the four
JTAG pins and VDD and GND. The EC takes its power from the application board. It requires roughly 20mA at
2.7-3.6V. For applications where there is not sufficient power available from the target board, the provided power
supply can be connected directly to the EC.
This is a vastly superior configuration for developing and debugging embedded applications compared to standard
MCU Emulators, which use on-board “ICE Chips” and target cables and require the MCU in the application board
to be socketed. Silicon Labs’ debug environment both increases ease of use and preserves the performance of the
precision analog peripherals.
Figure 1.7. Debug Environment Diagram
TARG ET P CB
RS-232
EC
C8051
F005
VDD GND
JTA G (x 4 ), V DD , GND
W INDO W S 95/98/NT/2000/XP
S ilicon Labs I n tegr a t e d
Development Environmen t
Rev. 1.7 16
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
1.4. Programmable Digital I/O and Crossbar
The standard 8051 Ports (0, 1, 2, and 3) are available on the MCUs. All four ports are pinned out on the
F000/05/10/15. Ports 0 and 1 are pinned out on the F001/06/11/16, and only Port 0 is pinned out on the
F002/07/12/17. The Ports not pinned out are still available for software use as general purpose registers. The Port
I/O behave like the standard 8051 with a few enhancements.
Each Port I/O pin can be configured as either a push-pull or open-drain output. Also, the “weak pull-ups” which are
normally fixed on an 8051 can be globally disabled, providing additional power saving capabilities for low power
applications.
Perhaps the most unique enh ancement is the Digital Crossbar. This is essentially a larg e digital switching network
that allows mapping of internal digital system resources to Port I/O pins on P0, P1, and P2. (See Figure 1.8.)
Unlike microcontrollers with standard multiplexed digital I/O, all combinations of functions are supported.
The on-board counter/timers, serial buses, HW interrupts, ADC Start of Conversion input, comparator outputs, and
other digital signals in the controller can be configured to appear on the Port I/O pins specified in the Crossbar
Control registers. This allows the user to select the exact mix of general purpose Port I/O and digital resources
needed for his particular application.
Figure 1.8. Digital Crossbar Diagram
XBR0, XBR1,
XBR 2 R egisters
PRT3CF
Register
External
Pins
P0
P1
P2
8
8
8
(Internal Digital Signals)
Port
Latches
P3
P3
I/O
Cells
P3.0
Digital
Crossbar
Priority
Decoder
P1
I/O
Cells
SMBus 2
SPI 4
UART 2
PCA 6
T0, T1,
T2 6
SYSCLK
CNVSTR
P3.7
P1.0
P1.7
P2
I/O
Cells
P2.0
P2.7
P0
I/O
Cells
P0.0
P0.7
8
Highest
Priority
Lowest
Priority
Highest
Priority
Lowest
Priority
8
8
(P2.0-P2.7)
(P1.0-P1.7)
(P0.0-P0.7)
8
PRT0CF, PRT1CF,
PRT2CF Registers
(P3.0-P3.7)
C o mptr.
Outputs 2
17 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
1.5. Programmable Counter Array
The C8051F000 MCU family has an on-board Programmable Counter/Timer Array (PCA) in addition to the four
16-bit general-purpose counter/timers. The PCA consists of a dedicated 16-bit counter/timer timebase with 5
programmable capture/compare modules. The timebase gets its clock from one of four sources: the system clock
divided by 12, the system clock divided by 4, Timer 0 overflow, or an External Clock Input (ECI).
Each capture/compare module can be configured to operate in one of four modes: Edge-Triggered Capture,
Software Timer, High Speed Output, or Pulse Width Modulator. The PCA Capture/Compare Module I/O and
External Clock Input are routed to the MCU Port I/O via the Digital Crossbar.
Figure 1.9. PCA Block Diagram
1.6. Serial Ports
The C8051F000 MCU Family includes a Full-Duplex UART, SPI Bus, and I2C/SMBus. Each of the serial buses is
fully implemented in hardware and makes extensive use of the CIP-51’s interrupts, thus requiring very little
intervention by the CPU. The serial buses do not “share” resources such as timers, interrupts, or Port I/O, so any or
all of the serial buses may be used together.
16-Bit Counter/Tim er
Capture/Compare
M odule 1
Capture/Compare
Module 0 Capture/Compare
M odule 2 Capture/Compare
Module 3 Capture/Compare
M odule 4
CEX1
System
Clock /12
T0 O verflow
ECI
Crossbar
CEX2
CEX3
CEX4
CEX0
P o rt I/O
/4
Rev. 1.7 18
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
1.7. Analog to Digital Converter
The C8051F000/1/2/5/6/7 has an on-chip 12-bit SAR ADC with a 9-channel input multiplexer and programmable
gain amplifier. With a maximum throughput of 100ksps, the ADC offers true 12-bit accuracy with an INL of
1LSB. The ADC in the C8051F010/1/2/5/6/7 is similar, but with 10-bit resolution. Each ADC has a maximum
throughput of 100ksps. Each ADC has an INL of 1LSB, offering true 12-bit accuracy with the C8051F00x, and
true 10-bit accuracy with the C8051F01x. There is also an on-board 15ppm voltage reference, or an external
reference may be used via the VREF pin.
The ADC is under full control of the CIP-51 microcontroller via the Special Function Registers. One input channel
is tied to an internal temperature sensor, while the other eight channels are available externally. Each pair of the
eight external input channels can be configured as either two single-ended inputs or a single differential input. The
system controller can also put the ADC into shutdown to save power.
A programmable gain amplifier follows the analog multiplexer. The gain can be set in software from 0.5 to 16 in
powers of 2. The gain stage can be especially useful when different ADC input channels have widely varied input
voltage signals, or when it is necessary to “zoom in” on a signal with a large DC offset (in differential mode, a DAC
could be used to provide the DC offset).
Conversions can be started in four ways; a software command, an overflow on Timer 2, an overflow on Timer 3, or
an external signal input. This flexibility allows the start of conversion to be triggered by software events, external
HW signals, or convert continuously. A completed conversion causes an interrupt, or a status bit can be polled in
software to determine the end of conversion. The resulting 10 or 12-bit data word is latched into two SFRs upon
completion of a conversion. The data can be right or left justified in these registers under software control.
Compare registers for the ADC data can be configured to interrupt the controller when ADC data is within a
specified window. The ADC can monitor a key voltage continuously in background mode, but not interrupt the
controller unless the converted data is within the specified window.
Figure 1.10. ADC Diagram
100ksps
SA R
ADC
+
-
Control & Data
SFR's
SFR Bus
+
-
+
-
+
-
9-to-1
AMUX
(SE or
DIFF)
+
-
X
AIN0
AIN1
AIN2
AIN3
AIN4
AIN5
AIN6
AIN7
TEMP
SENSOR
Programm able
Gain Amp
VREF
REF
(not bonded out on
F002, F007, F012,
and F017
19 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
1.8. Comparators and DACs
The C8051F000 MCU Family has two 12-bit DACs and two comparators on chip (the second comparator, CP1, is
not bonded out on the F002, F007, F012, and F017). The MC U data and control interface to each comparator and
DAC is via the Special Function Registers. The MCU can place any DAC or comparator in low power shutdown
mode.
The comparators have software programmable hysteresis. Each comparator can generate an interrupt on its rising
edge, falling edge, or both. The comparators’ output state can also be polled in software. These interrupts are
capable of waking up the MCU from idle mode. The comparator outputs can be programmed to appear on the Port
I/O pins via the Crossbar.
The DACs are voltage output mode and use the same voltage reference as the ADC. They are especially useful as
references for the comparators or offsets for the differential inputs of the ADC.
Figure 1.11. Comparator and DAC Diagram
SFR's
(Data
and
Cntrl)
CP1
CP1+
CP1-
DAC0
DAC0
DAC1
DAC1
REF
REF
CP0
CP0+
CP0-
CIP-51
and
Interrupt
Handler
CROSSBAR
CP1
CP0
(Port I/O)
(Port I/O)
+
-
CP0
+
-
CP1
(not bonded out on
F002, F007, F012, and
F017)
Rev. 1.7 20
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
2. ABSOLUTE MAXIMUM RATINGS*
Ambient temperature under bias ................................................................................................................. -55 to 125C
Storage Temperature .................................................................................................................................. -65 to 150C
Voltage on any Pin (except VDD and Port I/O) with respect to DGND ................................... -0.3V to (VDD + 0.3V)
Voltage on any Port I/O Pin or /RST with respect to DGND .................................................................... -0.3V to 5.8V
Voltage on VDD with respect to DGND ................................................................................................... -0.3V to 4.2V
Maximum Total current through VDD, AV+, DGND and AGND ..................................................................... 800mA
Maximum output current sunk by any Port pin ................................................................................................... 100mA
Maximum output current sunk by any other I/O pin ............................................................................................. 25mA
Maximum output current sourced by any Port pin .............................................................................................. 100mA
Maximum output current sourced by any other I/O pin ........................................................................................ 25mA
*Note: Stresses above those listed under “Absolute Maximu m Ratings” may cause permanent damage to the device.
This is a stress rating only and functional operation of the devices at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for
extended period s may affect device reliability.
3. GLOBAL DC ELECTRICAL CHARACTERISTICS
-40C to +85C unless otherwise specified.
PARAMETER CONDITIONS MIN TYP MAX UNITS
Analog Supply Voltage (Note 1) 2.7 3.0 3.6 V
Analog Supply Current Internal REF, ADC, DAC, Comparators
all active 1 2 mA
Analog Supply Current with
analog sub-systems inactive Internal REF, ADC, DAC, Comparators
all disabled, oscillator disabled 5 20
A
Analog-to-Digital Supply
Delta ( | VDD – AV+ | ) 0.5 V
Digital Supply Voltage 2.7 3.0 3.6 V
Digital Supply Current with
CPU active VDD = 2.7V, Clock=25MHz
VDD = 2.7V, Clock=1MHz
VDD = 2.7V, Clock=32kHz
12.5
0.5
10
mA
mA
A
Digital Supply Current
(shutdown) Oscillator not running 5 A
Digital Supply RAM Data
Retention Voltage 1.5 V
Specified Operating
Temperature Range -40 +85
C
SYSCLK (System Clock
Frequency) C8051F005/6/7, C8051F015/6/7
(Note 2) 0 25 MHz
SYSCLK (System Clock
Frequency) C8051F000/1/2, C8051F010/1/2
(Note 2) 0 20 MHz
Tsysl (SYSCLK Low Time) 18 ns
Tsysh (SYSCLK High Time) 18 ns
Note 1: Analog Supply AV+ must be greater than 1V for VDD monitor to operate.
Note 2: SYSCLK must be at least 32 kHz to enable debugging.
21 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
4. PINOUT AND PACKAGE DEFINITIONS
Table 4.1. Pin Definitions
Name
Pin Numbers
Type Description
F000
F005
F010
F015
F001
F006
F011
F016
F002
F007
F012
F017
VDD 31,
40,
62
23,
32 18,
20 Digital Voltage Supply.
DGND 30,
41,
61
22,
33,
27,
19
17,
21 Digital Ground.
AV+ 16,
17 13,
43 9,
29 Positive Analog Voltage Supply.
AGND 5,
15 44,
12 8,
30 Analog Ground.
TCK 22 18 14
D In JTAG Test Clock with internal pull-up.
TMS 21 17 13
D In JTAG Test-Mode Select with internal pull-up.
TDI 28 20 15
D In JTAG Test Data Input with internal pull-up. TDI is latched on a rising edge of
TCK.
TDO 29 21 16
D Out JTAG Test Data Output with internal pull-up. Data is shifted out on TDO on
the falling edge of TCK. TDO output is a tri-state driver.
XTAL1 18 14 10
A In Cry stal Input. This pin is the return for the internal oscillator circuit for a
crystal or ceramic resonator. For a precision internal clock, connect a crystal
or ceramic resonator from XTAL1 to XTAL2. If overdriven by an external
CMOS clock, this becomes the system clock.
XTAL2 19 15 11
A Out Crystal Output. This pin is the excitation driver for a crystal or ceramic
resonator.
/RST 20 16 12
D I/O Chip Reset. Open-drain output of internal Voltage Supply monitor. Is driven
low when VDD is < 2.7V. An external source can force a system reset by
driving this pin low.
VREF 6 3 3
A I/O Voltage Reference. When configured as an input, this pin is the voltage
reference for the MCU. Otherwise, the internal reference drives this pin.
CP0+ 4 2 2
A In Comparator 0 Non-Inverting Input.
CP0- 3 1 1
A In Comparator 0 Inverting Input.
CP1+ 2 45 A In Comparator 1 Non-Inverting Input.
CP1- 1 46 A In Comparator 1 Inverting Input.
DAC0 64 48 32
A Out Digital to Analog Converter Output 0. The DAC0 voltage output. (See
Section 7 DAC Specification for complete description).
DAC1 63 47 31
A Out Digital to Analog Converter Output 1. The DAC1 voltage output. (See
Section 7 DAC Specification for complete description).
AIN0 7 4 4
A In Analog Mux Channel Input 0. (See ADC Specification for complete
description).
AIN1 8 5 5
A In Analog Mux Channel Input 1. (See ADC Specification for complete
description).
AIN2 9 6 6
A In Analog Mux Channel Input 2. (See ADC Specification for complete
description).
AIN3 10 7 7
A In Analog Mux Channel Input 3. (See ADC Specification for complete
description).
AIN4 11 8 A In Analog Mux Channel Input 4. (See ADC Specification for complete
description).
AIN5 12 9 A In Analog Mux Channel Input 5. (See ADC Specification for complete
description).
Rev. 1.7 22
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Name
Pin Numbers
Type Description
F000
F005
F010
F015
F001
F006
F011
F016
F002
F007
F012
F017
AIN6 13 10 A In Analog Mux Channel Input 6. (See ADC Specification for complete
description).
AIN7 14 11 A In Analog Mux Channel Input 7. (See ADC Specification for complete
description).
P0.0 39 31 19
D I/O Port0 Bit0. (See the Port I/O Sub-System section for complete description).
P0.1 42 34 22
D I/O Port0 Bit1. (See the Port I/O Sub-System section for complete description).
P0.2 47 35 23
D I/O Port0 Bit2. (See the Port I/O Sub-System section for complete description).
P0.3 48 36 24
D I/O Port0 Bit3. (See the Port I/O Sub-System section for complete description).
P0.4 49 37 25
D I/O Port0 Bit4. (See the Port I/O Sub-System section for complete description).
P0.5 50 38 26
D I/O Port0 Bit5. (See the Port I/O Sub-System section for complete description).
P0.6 55 39 27
D I/O Port0 Bit6. (See the Port I/O Sub-System section for complete description).
P0.7 56 40 28
D I/O Port0 Bit7. (See the Port I/O Sub-System section for complete description).
P1.0 38 30 D I/O Port1 Bit0. (See the Port I/O Sub-System section for complete description).
P1.1 37 29 D I/O Port1 Bit1. (See the Port I/O Sub-System section for complete description).
P1.2 36 28 D I/O Port1 Bit2. (See the Port I/O Sub-System section for complete description).
P1.3 35 26 D I/O Port1 Bit3. (See the Port I/O Sub-System section for complete description).
P1.4 34 25 D I/O Port1 Bit4. (See the Port I/O Sub-System section for complete description).
P1.5 32 24 D I/O Port1 Bit5. (See the Port I/O Sub-System section for complete description).
P1.6 60 42 D I/O Port1 Bit6. (See the Port I/O Sub-System section for complete description).
P1.7 59 41 D I/O Port1 Bit7. (See the Port I/O Sub-System section for complete description).
P2.0 33
D I/O Port2 Bit0. (See the Port I/O Sub-System section for complete description).
P2.1 27
D I/O Port2 Bit1. (See the Port I/O Sub-System section for complete description).
P2.2 54
D I/O Port2 Bit2. (See the Port I/O Sub-System section for complete description).
P2.3 53
D I/O Port2 Bit3. (See the Port I/O Sub-System section for complete description).
P2.4 52
D I/O Port2 Bit4. (See the Port I/O Sub-System section for complete description).
P2.5 51
D I/O Port2 Bit5. (See the Port I/O Sub-System section for complete description).
P2.6 44
D I/O Port2 Bit6. (See the Port I/O Sub-System section for complete description).
P2.7 43
D I/O Port2 Bit7. (See the Port I/O Sub-System section for complete description).
P3.0 26
D I/O Port3 Bit0. (See the Port I/O Sub-System section for complete description).
P3.1 25
D I/O Port3 Bit1. (See the Port I/O Sub-System section for complete description).
P3.2 24
D I/O Port3 Bit2. (See the Port I/O Sub-System section for complete description).
P3.3 23
D I/O Port3 Bit3. (See the Port I/O Sub-System section for complete description).
P3.4 58
D I/O Port3 Bit4. (See the Port I/O Sub-System section for complete description).
P3.5 57
D I/O Port3 Bit5. (See the Port I/O Sub-System section for complete description).
P3.6 46
D I/O Port3 Bit6. (See the Port I/O Sub-System section for complete description).
P3.7 45
D I/O Port3 Bit7. (See the Port I/O Sub-System section for complete description).
23 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 4.1. TQFP-64 Pinout Diagram
1
2
3
4
5
6
7
8
9
10
11
17
18
19
20
21
22
23
24
25
26
27
48
47
46
45
44
43
42
41
40
39
38
64
63
62
61
60
59
58
57
56
55
54
VD
D
AGND
P0.3
P0.5
P0.6
P0.7
AGND
P0.0
P0.1
P0.2
P1.5
P1.4
P1.3
P1.2
P1.1
P0.4
XTAL2
TM
S
TCK
/RST
XTAL1
DAC
0
TDO
TDI
DGND
DAC
1
AIN0
AIN1
AIN2
AIN3
AIN4
AIN5
AIN6
AIN7
VRE
F
AV+
VD
D
DGND
P1.0
12
13
14
15
16
28
29
30
31
32
37
36
35
34
33
53
52
51
50
49
P1.6
P1.7
P2.2
P2.3
P3.6
P3.7
P2.6
P2.7
P3.0
P3.1
P3.2
P3.3
CP0-
CP1+
CP1-
CP0+
P2.0
P2.1
P3.5
P3.4
DGND
VD
D
AV+
P2.4
P2.5
C8051F000
C8051F005
C8051F010
C8051F015
Rev. 1.7 24
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 4.2. TQFP-64 Package Drawing
A
A1
A2
b
D
D1
e
E
-
0.05
0.95
0.17
-
-
-
-
-
-
0.22
12.00
10.00
0.50
12
00
MIN
(mm) NOM
(mm)
(
1
64
E
E1
e
D
D1
PIN 1
DESIGNATOR
A
2
25 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 4.3. TQFP-48 Pinout Diagram
1
2
3
4
5
6
7
8
9
10
11
12
36
35
34
33
32
31
30
29
28
27
26
25
48
47
46
45
44
43
42
41
40
39
38
37
AGND
P0.3
P0.5
P0.6
P0.7
AGND
P0.0
P0.1
P0.2
P1.5
P1.4
P1.3
P1.2
P1.1
P0.4
XTAL2
TMS
TCK
/RST
XTAL1
DAC0
TDO
TDI
DGND
DAC1
AIN0
AIN1
AIN2
AIN3
AIN4
AIN5
AIN6
AIN7
VREF
AV+
DGND
P1.0
P1.6
P1.7
CP0-
CP1+
CP1-
CP0+
AV+
13
14
15
16
17
18
19
20
21
22
23
24
DGND
VDD
VDD
DGND
C8051F001
C8051F006
C8051F011
C8051F016
Rev. 1.7 26
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 4.4. TQFP-48 Package Drawing
A
A1
A2
b
D
D1
e
E
E1
-
0.05
0.95
0.17
-
-
-
-
-
-
-
1.00
0.22
9.00
7.00
0.50
9.00
7.00
1.20
0.15
1.05
0.27
-
-
-
-
-
MIN
(mm) NOM
(mm) MAX
(mm)
E
E1
D
D1
48
1
A1
e
b
PIN 1
IDENTIFIER
A2
A
27 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 4.5. LQFP-32 Pinout Diagram
1
AGND
P0.3
P0.5
P0.6
P0.7
AGND
P0.0
P0.1
P0.2
P0.4
XTAL2
TMS
TCK
/RST
XTAL1
DAC0
TDO
TDI
DGND
DAC1
AIN0
AIN1
AIN2
AIN3
VREF
AV+
CP0-
CP0+
AV+
VDD
DGND
C8051F002
C8051F007
C8051F012
C8051F017
2
3
4
5
6
7
8
24
23
22
21
20
19
18
17
9
10
11
12
13
14
15
16
32
31
30
29
28
27
26
25
VDD
Rev. 1.7 28
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 4.6. LQFP-32 Package Drawing
A
A1
A2
b
D
D1
e
E
E1
-
0.05
1.35
0.30
-
-
-
-
-
-
-
1.40
0.37
9.00
7.00
0.80
9.00
7.00
1.60
0.15
1.45
0.45
-
-
-
-
-
MIN
(mm) NOM
(mm) MAX
(mm)
PIN 1
IDENTIFIER
A1
eb
1
32
E1
D1
D
E
A2 A
29 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
5. ADC (12-Bit, C8051F000/1/2/5/6/7 Only)
The ADC subsystem for the C8051F000/1/2/5/6/7 consists of a 9-channel, configurable analog multiplexer
(AMUX), a programmable gain amplifier (PGA), and a 100ksps, 12-bit successive-approximation-register ADC
with integrated track-and-hold and programmable window detector (see block diagram in Figure 5.1). The AMUX,
PGA, Data Conversion Modes, and Window Detector are all configurable under software control via the Special
Function Register’s shown in Figure 5.1. The ADC subsystem (ADC, track-and-hold and PGA) is enabled only
when the ADCEN bit in the ADC Con trol register (ADC0CN, Figu re 5.7) is set to 1. The ADC subsystem is in low
power shutdown when this bit is 0. The Bias Enable bit (BIASE) in the REF0CN register (see Figure 9.2) must be
set to 1 in order to supply bias to the ADC.
Figure 5.1. 12-Bit ADC Functional Block Diagram
5.1. Analog Multiplexer and PGA
Eight of the AMUX channels are available for external measurements while the ninth channel is internally
connected to an on-board temperature sensor (temperature transfer function is shown in Figure 5.3). Note that the
PGA gain is applied to the temperature sensor reading. AMUX input pairs can be programmed to operate in either
the differential or single-ended mode. This allows the user to select the best measurement technique for each input
channel, and even accommodates mode changes “on-the-fly”. The AMUX defaults to all single-ended inputs upon
reset. There are two registers associated with the AMUX: the Channel Selection register AMX0SL (Figure 5.5),
and the Configuration register AMX0CF (Figure 5.4). The table in Figure 5.5 shows AMUX functionality by
channel for each possible configuration. The PGA amplifies the AMUX output signal by an amount determined by
the AMPGN2-0 bits in the ADC Configuration register, ADC0CF (Figure 5.6). The PGA can be software-
programmed for gains of 0.5, 1, 2, 4, 8 or 16. It defaults to unity gain on reset.
12-Bit
SAR
ADC
REF
+
-
AV+
TEMP
SENSOR
12
+
-
+
-
+
-
9-to-1
AMUX
(SE or
DIFF)
AV+
COMB
LOGIC
24
12
ADWINT
ADCEN
SYSCLK
+
-
X
AIN0
AIN1
AIN2
AIN3
AIN4
AIN5
AIN6
AIN7
TMR3 OV
T2 OV
CNVSTR
ADBUSY(w)
Conversion Start
AGND
AGND
AMX0CF
AIN01IC
AIN23IC
AIN45IC
AIN67IC
AMX0SL
AMXAD0
AMXAD1
AMXAD2
AMXAD3
ADC0CF
AMPGN0
AMPGN1
AMPGN2
ADCSC0
ADCSC1
ADCSC2
ADC0CN
ADLJST
ADWINT
ADSTM0
ADSTM1
ADBUSY
ADCINT
ADCTM
ADCEN
ADC0LADC0H
ADC0LTLADC0LTHADC0GTLADC0GTH
Rev. 1.7 30
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
5.2. ADC Modes of Operation
The ADC uses VREF to determine its full-scale voltage, thus the reference must be properly configured before
performing a conversion (see Section 9). The ADC has a maximum conversion speed of 100ksps. The ADC
conversion clock is derived from the system clock. Conversion clock speed can be reduced by a factor of 2, 4, 8 or
16 via the ADCSC bits in the ADC0CF Register. This is useful to adjust conversion speed to accommodate
different system clock speeds.
A conversion can be initiated in one of four ways, depending on the programmed states of the ADC Start of
Conversion Mode bits (ADSTM1, ADSTM0) in ADC0CN. Conversions may be initiated by:
1. Writing a 1 to the ADBUSY bit of ADC0CN;
2. A Timer 3 overflow (i.e. timed continuous conversions);
3. A rising edge detected on the external ADC convert start signal, CNVSTR;
4. A Timer 2 overflow (i.e. timed continuous conversions).
Writing a 1 to ADBUSY provides software control of the ADC whereby conversions are performed “on-demand”.
During conversion, the ADBUSY bit is set to 1 and restored to 0 when conversion is complete. The falling edge of
ADBUSY triggers an interrupt (when enabled) and sets the ADCINT interrupt flag. Note: When conversions are
performed “on-demand”, the ADCINT flag, not ADBUSY, should be polled to determine when the
conversion has completed. Converted data is available in the ADC data word MSB and LSB registers, ADC0H,
ADC0L. Converted data can be either left or right justified in the ADC0H:ADC0L register pair (see example in
Figure 5.9) depending on the programmed state of the ADLJST bit in the ADC0CN register.
The ADCTM bit in register ADC0CN controls the ADC track-and-hold mode. In its default state, the ADC input is
continuously tracked, except when a conversion is in progress. Setting ADCTM to 1 allows one of four different
low power track-and-hold modes to be specified by states of the ADSTM1-0 bits (also in ADC0CN):
1. Tracking begins with a write of 1 to ADBUSY and lasts for 3 SAR clocks;
2. Tracking starts with an overflow of Timer 3 and lasts for 3 SAR clocks;
3. Tracking is active only when the CNVSTR input is low;
4. Tracking starts with an overflow of Timer 2 and lasts for 3 SAR clocks.
Modes 1, 2 and 4 (above) are useful when the start of conversion is triggered with a software command or when the
ADC is operated continuously. Mode 3 is used when the start of conversion is triggered by external hardware. In
this case, the track-and-hold is in its low power mode at times when the CNVSTR input is high. Tracking can also
be disabled (shutdown) when the entire chip is in low power standby or sleep modes.
Figure 5.2. 12-Bit ADC Track and Conversion Example Timing
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
CNVSTR
(ADSTM[1:0]=10)
ADCTM=1 Track Convert Low Power Mode
ADCTM=0
Track Or Convert
Convert Track
Low Power or
Convert
Timer2, Timer3 Overflow;
Write 1 to ADBUSY
(ADSTM[1:0]=00, 01, 11)
ADCTM=1 Track Convert Low Power Mode
ADCTM=0
Track or Convert
Convert Track
Low Power or
Convert
A. ADC Timing for External Trigger Source
B. ADC Timing for Internal Trigger Sources
SAR Clocks
SAR Clocks
1234567891011121314151617 18 19
12345678910111213141516
SAR Clocks
31 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 5.3. Temperature Sensor Transfer Function
Figure 5.4. AMX0CF: AMUX Configuration Register (C8051F00x)
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
- - - - AIN67IC AIN45IC AIN23IC AIN01IC 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xBA
Bits7-4: UNUSED. Read = 0000b; Write = don’t care
Bit3: AIN67IC: AIN6, AIN7 Input Pair Configuration Bit
0: AIN6 and AIN7 are independent singled-ended inputs
1: AIN6, AIN7 are (respectively) +, - differential input pair
Bit2: AIN45IC: AIN4, AIN5 Input Pair Configuration Bit
0: AIN4 and AIN5 are independent singled-ended inputs
1: AIN4, AIN5 are (respectively) +, - differential input pair
Bit1: AIN23IC: AIN2, AIN3 Input Pair Configuration Bit
0: AIN2 and AIN3 are independent singled-ended inputs
1: AIN2, AIN3 are (respectively) +, - differential input pair
Bit0: AIN01IC: AIN0, AIN1 Input Pair Configuration Bit
0: AIN0 and AIN1 are independent singled-ended inputs
1: AIN0, AIN1 are (respectively) +, - differential input pair
N
OTE: The ADC Data Word is in 2’s complement format for channels configured as differential.
0-50 50 100
(Celsius)
0.500
0.600
0.700
0.800
0.900
(Volts)
V
TEMP
= 0.00286(TEMP
C
) + 0.776
for PGA Gain = 1
1.000
Rev. 1.7 32
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 5.5. AMX0SL: AMUX Channel Select Register (C8051F00x)
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
- - - -
AMXAD3 AMXAD2 AMXAD1 AMXAD0 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xBB
AMXAD3-0
0000 0001 0010 0011 0100 0101 0110 0111 1xxx
0000 AIN0 AIN1 AIN2 AIN3 AIN4 AIN5 AIN6 AIN7
TEMP
SENSOR
0001 +(AIN0)
-(AIN1) AIN2 AIN3 AIN4 AIN5 AIN6 AIN7 TEMP
SENSOR
0010 AIN0 AIN1
+(AIN2)
-(AIN3) AIN4 AIN5 AIN6 AIN7
TEMP
SENSOR
0011 +(AIN0)
-(AIN1) +(AIN2)
-(AIN3) AIN4 AIN5 AIN6 AIN7
TEMP
SENSOR
0100 AIN0 AIN1 AIN2 AIN3
+(AIN4)
-(AIN5) AIN6 AIN7
TEMP
SENSOR
0101 +(AIN0)
-(AIN1) AIN2 AIN3
+(AIN4)
-(AIN5) AIN6 AIN7
TEMP
SENSOR
0110 AIN0 AIN1
+(AIN2)
-(AIN3) +(AIN4)
-(AIN5) AIN6 AIN7
TEMP
SENSOR
0111 +(AIN0)
-(AIN1) +(AIN2)
-(AIN3) +(AIN4)
-(AIN5) AIN6 AIN7
TEMP
SENSOR
1000 AIN0 AIN1 AIN2 AIN3 AIN4 AIN5
+(AIN6)
-(AIN7) TEMP
SENSOR
1001 +(AIN0)
-(AIN1) AIN2 AIN3 AIN4 AIN5
+(AIN6)
-(AIN7) TEMP
SENSOR
1010 AIN0 AIN1
+(AIN2)
-(AIN3) AIN4 AIN5
+(AIN6)
-(AIN7) TEMP
SENSOR
1011 +(AIN0)
-(AIN1) +(AIN2)
-(AIN3) AIN4 AIN5
+(AIN6)
-(AIN7) TEMP
SENSOR
1100 AIN0 AIN1 AIN2 AIN3
+(AIN4)
-(AIN5) +(AIN6)
-(AIN7) TEMP
SENSOR
1101 +(AIN0)
-(AIN1) AIN2 AIN3
+(AIN4)
-(AIN5) +(AIN6)
-(AIN7) TEMP
SENSOR
1110 AIN0 AIN1
+(AIN2)
-(AIN3) +(AIN4)
-(AIN5) +(AIN6)
-(AIN7) TEMP
SENSOR
1111 +(AIN0)
-(AIN1) +(AIN2)
-(AIN3) +(AIN4)
-(AIN5) +(AIN6)
-(AIN7) TEMP
SENSOR
Bits7-4: UNUSED. Read = 0000b; Write = don’t care
Bits3-0: AMXAD3-0: AMUX Address Bits
0000-1111: ADC Inputs selected per chart below
A
M
X
0
C
F
B
I
T
S
3
-
0
33 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 5.6. ADC0CF: ADC Configuration Register (C8051F00x)
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
ADCSC2 ADCSC1 ADCSC0 - - AMPGN2 AMPGN1 AMPGN0
01100000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xBC
Bits7-5: ADCSC2-0: ADC SAR Conversion Clock Period Bits
000: SAR Conversion Clock = 1 System Clock
001: SAR Conversion Clock = 2 System Clocks
010: SAR Conversion Clock = 4 System Clocks
011: SAR Conversion Clock = 8 System Clocks
1xx: SAR Conversion Clock = 16 Systems Clocks
(Note: the SAR Conversion Clock should be 2MHz)
Bits4-3: UNUSED. Read = 00b; Write = don’t care
Bits2-0: AMPGN2-0: ADC Internal Amplifier Gain
000: Gain = 1
001: Gain = 2
010: Gain = 4
011: Gain = 8
10x: Gain = 16
11x: Gain = 0.5
Rev. 1.7 34
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 5.7. ADC0CN: ADC Control Register (C8051F00x)
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
ADCEN ADCTM ADCINT ADBUSY ADSTM1 ADSTM0 ADWINT ADLJST 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
(bit addressable) 0xE8
Bit7: ADCEN: ADC En able Bit
0: ADC Disabled. ADC is in low power shutdown.
1: ADC Enabled. ADC is active and ready for data conversions.
Bit6: ADCTM: ADC Track Mode Bit
0: When the ADC is enabled, tracking is always done unless a conversion is in process
1: Tracking Defined by ADSTM1-0 bits
ADSTM1-0:
00: Tracking starts with the write of 1 to ADBUSY and lasts for 3 SAR clocks
01: Tracking started by the overflow of Timer 3 and last for 3 SAR clocks
10: ADC tracks only when CNVSTR input is logic low
11: Tracking started by the overflow of Timer 2 and last for 3 SAR clocks
Bit5: ADCINT: ADC Conversion Complete Interrupt Flag
(Must be cleared by software)
0: ADC has not completed a data conversion since the last time this flag was cleared
1: ADC has completed a data conversion
Bit4: ADBUSY: ADC Busy Bit
Read
0: ADC Conversion complete or no valid data has been converted since a reset. The falling
edge of ADBUSY generates an interrupt when enabled.
1: ADC Busy converting data
Write
0: No effect
1: Starts ADC Conversion if ADSTM1-0 = 00b
Bits3-2: ADSTM1-0: ADC Start of Conversion Mode Bits
00: ADC conversion started upon every write of 1 to ADBUSY
01: ADC conversions taken on every overflow of Timer 3
10: ADC conversion started upon every rising edge of CNVSTR
11: ADC conversions taken on every overflow of Timer 2
Bit1: ADWINT: ADC Window Compare Interrupt Flag
(Must be cleared by software)
0: ADC Window Comparison Data match has not occurred
1: ADC Window Comparison Data match occurred
Bit0: ADLJST: ADC Left Ju stify Data Bit
0: Data in ADC0H:ADC0L Registers is right justified
1: Data in ADC0H:ADC0L Registers is left justified
35 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 5.8. ADC0H: ADC Data Word MSB Register (C8051F00x)
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xBF
Figure 5.9. ADC0L: ADC Data Word LSB Register (C8051F00x)
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xBE
NOTE: Resulting 12-bit ADC Data Word appears in the ADC Data Word Registers as follows:
ADC0H[3:0]:ADC0L[7:0], if ADLJST = 0
(ADC0H[7:4] will be sign extension of ADC0H.3 if a differential reading, otherwise = 0000b)
ADC0H[7:0]:ADC0L[7:4], if ADLJST = 1
(ADC0L[3:0] = 0000b)
EXAMPLE: ADC Data Word Conversion Map, AIN0 Input in Single-Ended Mode
(AMX0CF=0x00, AMX0SL=0x00)
AIN0 – AGND
(Volts) ADC0H:ADC0L
(ADLJST = 0) ADC0H:ADC0L
(ADLJST = 1)
REF x (4095/4096) 0x0FFF 0xFFF0
REF x ½ 0x0800 0x8000
REF x (2047/4096) 0x07FF 0x7FF0
0 0x0000 0x0000
EXAMPLE: ADC Data Word Conversion Map, AIN0-AIN1 Differential Input Pair
(AMX0CF=0x01, AMX0SL=0x00)
AIN0 – AIN1 (Volts) ADC0H:ADC0L
(ADLJST = 0) ADC0H:ADC0L
(ADLJST = 1)
REF x (2047/2048) 0x07FF 0x7FF0
0 0x0000 0x0000
-REF x (1/2048) 0xFFFF 0xFFF0
-REF 0xF800 0x8000
Bits7-0: ADC Data Word Bits
For ADLJST = 1: Upper 8-bits of the 12-bit ADC Data Word.
For ADLJST = 0: Bits7-4 are the sign extension of Bit3. Bits 3-0 are the upper 4-bits of the
12-bit ADC Data Word.
Bits7-0: ADC Data Word Bits
For ADLJST = 1: Bits7-4 are the lower 4- bits of the 12-bit ADC Data Word. Bits3-0 will
always read 0.
For ADLJST = 0: Bits7-0 are the lower 8-bits of the 12-bit ADC Data Word.
Rev. 1.7 36
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
5.3. ADC Programmable Window Detector
The ADC programmable window detector is very useful in many applications. It continuously compares the ADC
output to user-programmed limits and notifies the system when an out-of-band condition is detected. This is
especially effective in an interrupt-driven system, saving code space and CPU bandwidth while delivering faster
system response times. The window detector interrupt flag (ADWINT in ADC0CN) can also be used in polled
mode. The high and low bytes of the reference words are loaded into the ADC Greater-Than and ADC Less-Than
registers (ADC0GTH, ADC0GTL, ADC0LTH, and ADC0LTL). Figure 5.14 and Figure 5.15 show example
comparisons for reference. Notice that the window detector flag can be asserted when the measured data is inside
or outside the user-programmed limits, depending on the programming of the ADC0GTx and ADC0LTx registers.
Figure 5.10. ADC0GTH: ADC Greater-Than Data High Byte Register (C8051F00x)
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
11111111
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xC5
Figure 5.11. ADC0GTL: ADC Greater-Than Data Low Byte Register (C8051F00x)
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
11111111
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xC4
Figure 5.12. ADC0LTH: ADC Less-Than Data High Byte Register (C8051F00x)
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xC7
Figure 5.13. ADC0LTL: ADC Less-Than Data Low Byte Register (C8051F00x)
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xC6
Bits7-0:
The high byte of the ADC Greater-Than Data Word.
Bits7-0:
The low byte of the ADC Greater-Than Data Word.
Definition:
ADC Greater-Than Data Word = ADC0GTH:ADC0GTL
Bits7-0:
The high byte of the ADC Less-Than Data Word.
Bits7-0:
These bits are the low byte of the ADC Less-Than Data Word.
Definition:
ADC Less-Than Data Word = ADC0LTH:ADC0LTL
37 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 5.14. 12-Bit ADC Window Interrupt Examples, Right Justified Data
0x0FFF
0x0201
0x0200
0x01FF
0x0101
0x0100
0x00FF
0x0000
ADWINT=1
ADWINT
not affected
ADWINT
not affected
ADC Data
Word
0x0FFF
0x0201
0x0200
0x01FF
0x0101
0x0100
0x00FF
0x0000
ADWINT=1
ADWINT
not affected
ADWINT=1
ADC0LTH:ADC0LTL
ADC0GTH:ADC0GTL
ADC Data
Word
ADC0GTH:ADC0GTL
ADC0LTH:ADC0LTL
0
Input Voltage
(AD0 - AGND)
REF x (4095/4096)
REF x (256/4096)
REF x (512/4096)
0
Input Voltage
(AD0 - AGND)
REF x (4095/4096)
REF x (256/4096)
REF x (512/4096)
0x07FF
0x0101
0x0100
0x00FF
0x0000
0xFFFF
0xFFFE
0xF800
ADWINT=1
ADWINT
not affected
ADWINT
not affected
0x07FF
0x0101
0x0100
0x00FF
0x0000
0xFFFF
0xFFFE
0xF800
ADWINT=1
ADWINT
not affected
-REF
Input Voltage
(AD0 - AD1)
ADWINT=1
REF x (2047/2048)
ADC0LTH:ADC0LTL
ADC0GTH:ADC0GTL
ADC Data
Word
ADC Data
Word
ADC0LTH:ADC0LTL
ADC0GTH:ADC0GTL
REF x (256/2048)
REF x (-1/2048)
-REF
Input Voltage
(AD0 - AD1)
REF x (2047/2048)
REF x (256/2048)
REF x (-1/2048)
Given:
AMX0SL = 0x00, AMX0CF = 0x00, ADLJST = 0,
ADC0LTH:ADC0LTL = 0x0200,
ADC0GTH:ADC0GTL = 0x0100.
An ADC End of Conversion will cause an ADC Window
Compare Interrupt (ADWINT=1) if the resulting ADC
Data Word is < 0x0200 and > 0x0100.
Given:
AMX0SL = 0x00, AMX0CF = 0x00, ADLJST = 0,
ADC0LTH:ADC0LTL = 0x0100,
ADC0GTH:ADC0GTL = 0x0200.
An ADC End of Conversion will cause an ADC Window
Compare Interrupt (ADWINT=1) if the resulting ADC
Data Word is < 0x0100 or > 0x0200.
Given:
AMX0SL = 0x00, AMX0CF = 0x01, ADLJST = 0,
ADC0LTH:ADC0LTL = 0x0100,
ADC0GTH:ADC0GTL = 0xFFFF.
An ADC End of Conversion will cause an ADC Window
Compare Interrupt (ADWINT=1) if the resulting ADC
Data Word is < 0x0100 and > 0xFFFF. (Two’s
Complement math, 0xFFFF = -1.)
Given:
AMX0SL = 0x00, AMX0CF = 0x01, ADLJST = 0,
ADC0LTH:ADC0LTH = 0xFFFF,
ADC0GTH:ADC0GTL = 0x0100.
An ADC End of Conversion will cause an ADC Window
Compare Interrupt (ADWINT=1) if the resulting ADC
Data Word is < 0xFFFF or > 0x0100. (Two’s Complement
math, 0xFFFF = -1.)
Rev. 1.7 38
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 5.15. 12-Bit ADC Window Interrupt Examples, Left Justified Data
0xFFF0
0x2010
0x2000
0x1FF0
0x1010
0x1000
0x0FF0
0x0000
ADWINT=1
ADWINT
not affected
ADWINT
not affected
ADC Data
Word
0xFFF0
0x2010
0x2000
0x1FF0
0x1010
0x1000
0x0FF0
0x0000
ADWINT=1
ADWINT
not affected
ADWINT=1
ADC0LTH:ADC0LTL
ADC0GTH:ADC0GTL
ADC Data
Word
ADC0GTH:ADC0GTL
ADC0LTH:ADC0LTL
0
Input Voltage
(AD0 - AGND)
REF x (4095/4096)
REF x (256/4096)
REF x (512/4096)
0
Input Voltage
(AD0 - AGND)
REF x (4095/4096)
REF x (256/4096)
REF x (512/4096)
Given:
AMX0SL = 0x00, AMX0CF = 0x00, ADLJST = 1,
ADC0LTH:ADC0LTL = 0x2000,
ADC0GTH:ADC0GTL = 0x1000.
An ADC End of Conversion will cause an ADC Window
Compare Interrupt (ADWINT=1) if the resulting ADC
Data Word is < 0x2000 and > 0x1000.
Given:
AMX0SL = 0x00, AMX0CF = 0x00, ADLJST = 1,
ADC0LTH:ADC0LTL = 0x1000,
ADC0GTH:ADC0GTL = 0x2000.
An ADC End of Conversion will cause an ADC Window
Compare Interrupt (ADWINT=1) if the resulting ADC
Data Word is < 0x1000 or > 0x2000.
Given:
AMX0SL = 0x00, AMX0CF = 0x01, ADLJST = 1,
ADC0LTH:ADC0LTL = 0x1000,
ADC0GTH:ADC0GTL = 0xFFF0.
An ADC End of Conversion will cause an ADC Window
Compare Interrupt (ADWINT=1) if the resulting ADC
Data Word is < 0x1000 and > 0xFFF0. (Two’s
Complement mat h . )
Given:
AMX0SL = 0x00, AMX0CF = 0x01, ADLJST = 1,
ADC0LTH:ADC0LTH = 0xFFF0,
ADC0GTH:ADC0GTL = 0x1000.
An ADC End of Conversion will cause an ADC Window
Compare Interrupt (ADWINT=1) if the resulting ADC
Data Word is < 0xFFF0 or > 0x1000. (Two’s Complement
math.)
0x7FF0
0x1010
0x1000
0x0FF0
0x0000
0xFFF0
0xFFE0
0x8000
ADWINT=1
ADWINT
not affected
ADWINT
not affected
0x7FF0
0x1010
0x1000
0x0FF0
0x0000
0xFFF0
0xFFE0
0x8000
ADWINT=1
ADWINT
not affected
-REF
Input Voltage
(AD0 - AD1)
ADWINT=1
REF x (2047/2048)
ADC0LTH:ADC0LTL
ADC0GTH:ADC0GTL
ADC Data
Word
ADC Data
Word
ADC0LTH:ADC0LTL
ADC0GTH:ADC0GTL
REF x (256/2048)
REF x (-1/2048)
-REF
Input Voltage
(AD0 - AD1)
REF x (2047/2048)
REF x (256/2048)
REF x (-1/2048)
39 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Table 5.1. 12-Bit ADC Electrical Characteristics
VDD = 3.0V, AV+ = 3.0V, VREF = 2.40V (REFBE=0), PGA Gain = 1, -40C to +85C unless otherwise specified.
PARAMETER CONDITIONS MIN TYP MAX UNITS
DC ACCURACY
Resolution 12 bits
Integral Nonlinearity 1 LSB
Differential Nonlinearity Guaranteed Monotonic 1 LSB
Offset Error -3 1 LSB
Full Scale Error Differential mode -7 3 LSB
Offset Temperature
Coefficient
0.25 ppm/C
DYNAMIC PERFORMANCE (10kHz sine-wave input, 0 to –1dB of full scale, 100ksps)
Signal-to-Noise Plus
Distortion 66 69 dB
Total Harmonic Distortion Up to the 5th harmonic -75 dB
Spurious-Free Dynamic
Range 80 dB
CONVERSION RATE
Conversion Time in SAR
Clocks 16 clocks
SAR Clock Frequency C8051F000, ‘F001, ‘F002
C8051F005, ‘F006, ‘F007 2.0
2.5 MHz
MHz
Track/Hold Acquisition
Time 1.5
s
Throughput Rate 100 ksps
ANALOG INPUTS
Voltage Conversion Range Single-ended Mode (AINn – AGND)
Differential Mode |(AINn+) – (AINm-)| 0 VREF
- 1LSB V
Input Voltage Any AINn pin AGND AV+ V
Input Capacitance 10 pF
TEMPERATURE SENSOR
Linearity
0.20 C
Absolute Accuracy 3 C
Gain PGA Gain = 1 2.86 mV/C
Gain Error (1) PGA Gain = 1 33.5 V/C
Offset PGA Gain = 1, Temp = 0C 776 mV
Offset Error (1) PGA Gain = 1, Temp = 0C 8.51 mV
POWER SPECIFICATIONS
Power Supply Current (AV+
supplied to ADC) Operating Mode, 100ksps 450 900 A
Power Supply Rejection 0.3 mV/V
Rev. 1.7 40
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
6. ADC (10-Bit, C8051F010/1/2/5/6/7 Only)
The ADC subsystem for the C8051F010/1/2/5/6/7 consists of a 9-channel, configurable analog multiplexer
(AMUX), a programmable gain amplifier (PGA), and a 100ksps, 10-bit successive-approximation-register ADC
with integrated track-and-hold and programmable window detector (see block diagram in Figure 6.1). The AMUX,
PGA, Data Conversion Modes, and Window Detector are all configurable under software control via the Special
Function Register’s shown in Figure 6.1. The ADC subsystem (ADC, track-and-hold and PGA) is enabled only
when the ADCEN bit in the ADC Con trol register (ADC0CN, Figu re 6.7) is set to 1. The ADC subsystem is in low
power shutdown when this bit is 0. The Bias Enable bit (BIASE) in the REF0CN register (see Figure 9.2) must be
set to 1 in order to supply bias to the ADC.
Figure 6.1. 10-Bit ADC Functional Block Diagram
6.1. Analog Multiplexer and PGA
Eight of the AMUX channels are available for external measurements while the ninth channel is internally
connected to an on-board temperature sensor (temperature transfer function is shown in Figure 6.3). Note that the
PGA gain is applied to the temperature sensor reading. AMUX input pairs can be programmed to operate in either
the differential or single-ended mode. This allows the user to select the best measurement technique for each input
channel, and even accommodates mode changes “on-the-fly”. The AMUX defaults to all single-ended inputs upon
reset. There are two registers associated with the AMUX: the Channel Selection register AMX0SL (Figure 6.5),
and the Configuration register AMX0CF (Figure 6.4). The table in Figure 6.5 shows AMUX functionality by
channel for each possible configuration. The PGA amplifies the AMUX output signal by an amount determined by
the AMPGN2-0 bits in the ADC Configuration register, ADC0CF (Figure 6.6). The PGA can be software-
programmed for gains of 0.5, 1, 2, 4, 8 or 16. It defaults to unity gain on reset.
10-Bit
SAR
ADC
REF
+
-
AV+
TEMP
SENSOR
10
+
-
+
-
+
-
9-to-1
AMUX
(SE or
DIFF)
AV+
COMB
LOGIC
20
10
ADWINT
ADCEN
SYSCLK
+
-
X
AIN0
AIN1
AIN2
AIN3
AIN4
AIN5
AIN6
AIN7
TMR3 OV
T2 OV
CNVSTR
ADBUSY(w)
Conversion Start
AGND
AGND
AMX0CF
AIN01IC
AIN23IC
AIN45IC
AIN67IC
AMX0SL
AMXAD0
AMXAD1
AMXAD2
AMXAD3
ADC0CF
AMPGN0
AMPGN1
AMPGN2
ADCSC0
ADCSC1
ADCSC2
ADC0CN
ADLJST
ADWINT
ADSTM0
ADSTM1
ADBUSY
ADCINT
ADCTM
ADCEN
ADC0LADC0H
ADC0LTLADC0LTHADC0GTLADC0GTH
41 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
6.2. ADC Modes of Operation
The ADC uses VREF to determine its full-scale voltage, thus the reference must be properly configured before
performing a conversion (see Section 9). The ADC has a maximum conversion speed of 100ksps. The ADC
conversion clock is derived from the system clock. Conversion clock speed can be reduced by a factor of 2, 4, 8 or
16 via the ADCSC bits in the ADC0CF Register. This is useful to adjust conversion speed to accommodate
different system clock speeds.
A conversion can be initiated in one of four ways, depending on the programmed states of the ADC Start of
Conversion Mode bits (ADSTM1, ADSTM0) in ADC0CN. Conversions may be initiated by:
1. Writing a 1 to the ADBUSY bit of ADC0CN;
2. A Timer 3 overflow (i.e. timed continuous conversions);
3. A rising edge detected on the external ADC convert start signal, CNVSTR;
4. A Timer 2 overflow (i.e. timed continuous conversions).
Writing a 1 to ADBUSY provides software control of the ADC whereby conversions are performed “on-demand”.
During conversion, the ADBUSY bit is set to 1 and restored to 0 when conversion is complete. The falling edge of
ADBUSY triggers an interrupt (when enabled) and sets the ADCINT interrupt flag. Note: When conversions are
performed “on-demand”, the ADCINT flag, not ADBUSY, should be polled to determine when the
conversion has completed. Converted data is available in the ADC data word MSB and LSB registers, ADC0H,
ADC0L. Converted data can be either left or right justified in the ADC0H:ADC0L register pair (see example in
Figure 6.9) depending on the programmed state of the ADLJST bit in the ADC0CN register.
The ADCTM bit in register ADC0CN controls the ADC track-and-hold mode. In its default state, the ADC input is
continuously tracked, except when a conversion is in progress. Setting ADCTM to 1 allows one of four different
low power track-and-hold modes to be specified by states of the ADSTM1-0 bits (also in ADC0CN):
1. Tracking begins with a write of 1 to ADBUSY and lasts for 3 SAR clocks;
2. Tracking starts with an overflow of Timer 3 and lasts for 3 SAR clocks;
3. Tracking is active only when the CNVSTR input is low;
4. Tracking starts with an overflow of Timer 2 and lasts for 3 SAR clocks.
Modes 1, 2 and 4 (above) are useful when the start of conversion is triggered with a software command or when the
ADC is operated continuously. Mode 3 is used when the start of conversion is triggered by external hardware. In
this case, the track-and-hold is in its low power mode at times when the CNVSTR input is high. Tracking can also
be disabled (shutdown) when the entire chip is in low power standby or sleep modes.
Figure 6.2. 10-Bit ADC Track and Conversion Example Timing
12345678910111213141516
CNVSTR
(ADSTM[1:0]=10)
ADCTM=1 Track Convert Low Power Mode
ADCTM=0
Track Or Convert
Convert Track
Low Power or
Convert
Timer2, Timer3 Overflow;
Write 1 to ADBUSY
(ADSTM[1:0]=00, 01, 11)
ADCTM=1 Track Convert Low Power Mode
ADCTM=0
Track or Convert
Convert Track
Low Power or
Convert
A. ADC Timing for External Trigger Sourc
e
B. ADC Timing for Internal Trigger Sources
SAR Clocks
SAR Clocks
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
SAR Clocks
Rev. 1.7 42
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 6.3. Temperature Sensor Transfer Function
Figure 6.4. AMX0CF: AMUX Configuration Register (C8051F01x)
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
- - - - AIN67IC AIN45IC AIN23IC AIN01IC 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xBA
Bits7-4: UNUSED. Read = 0000b; Write = don’t care
Bit3: AIN67IC: AIN6, AIN7 Input Pair Configuration Bit
0: AIN6 and AIN7 are independent singled-ended inputs
1: AIN6, AIN7 are (respectively) +, - differential input pair
Bit2: AIN45IC: AIN4, AIN5 Input Pair Configuration Bit
0: AIN4 and AIN5 are independent singled-ended inputs
1: AIN4, AIN5 are (respectively) +, - differential input pair
Bit1: AIN23IC: AIN2, AIN3 Input Pair Configuration Bit
0: AIN2 and AIN3 are independent singled-ended inputs
1: AIN2, AIN3 are (respectively) +, - differential input pair
Bit0: AIN01IC: AIN0, AIN1 Input Pair Configuration Bit
0: AIN0 and AIN1 are independent singled-ended inputs
1: AIN0, AIN1 are (respectively) +, - differential input pair
N
OTE: The ADC Data Word is in 2’s complement format for channels configured as differential.
0-50 50 100
(Celsius)
0.500
0.600
0.700
0.800
0.900
(Volts)
V
TEMP
= 0.00286(TEMP
C
) + 0.776
for PGA Gain = 1
1.000
43 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 6.5. AMX0SL: AMUX Channel Select Register (C8051F01x)
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
- - - -
AMXAD3 AMXAD2 AMXAD1 AMXAD0 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xBB
AMXAD3-0
0000 0001 0010 0011 0100 0101 0110 0111 1xxx
0000 AIN0 AIN1 AIN2 AIN3 AIN4 AIN5 AIN6 AIN7
TEMP
SENSOR
0001 +(AIN0)
-(AIN1) AIN2 AIN3 AIN4 AIN5 AIN6 AIN7 TEMP
SENSOR
0010 AIN0 AIN1
+(AIN2)
-(AIN3) AIN4 AIN5 AIN6 AIN7
TEMP
SENSOR
0011 +(AIN0)
-(AIN1) +(AIN2)
-(AIN3) AIN4 AIN5 AIN6 AIN7
TEMP
SENSOR
0100 AIN0 AIN1 AIN2 AIN3
+(AIN4)
-(AIN5) AIN6 AIN7
TEMP
SENSOR
0101 +(AIN0)
-(AIN1) AIN2 AIN3
+(AIN4)
-(AIN5) AIN6 AIN7
TEMP
SENSOR
0110 AIN0 AIN1
+(AIN2)
-(AIN3) +(AIN4)
-(AIN5) AIN6 AIN7
TEMP
SENSOR
0111 +(AIN0)
-(AIN1) +(AIN2)
-(AIN3) +(AIN4)
-(AIN5) AIN6 AIN7
TEMP
SENSOR
1000 AIN0 AIN1 AIN2 AIN3 AIN4 AIN5
+(AIN6)
-(AIN7) TEMP
SENSOR
1001 +(AIN0)
-(AIN1) AIN2 AIN3 AIN4 AIN5
+(AIN6)
-(AIN7) TEMP
SENSOR
1010 AIN0 AIN1
+(AIN2)
-(AIN3) AIN4 AIN5
+(AIN6)
-(AIN7) TEMP
SENSOR
1011 +(AIN0)
-(AIN1) +(AIN2)
-(AIN3) AIN4 AIN5
+(AIN6)
-(AIN7) TEMP
SENSOR
1100 AIN0 AIN1 AIN2 AIN3
+(AIN4)
-(AIN5) +(AIN6)
-(AIN7) TEMP
SENSOR
1101 +(AIN0)
-(AIN1) AIN2 AIN3
+(AIN4)
-(AIN5) +(AIN6)
-(AIN7) TEMP
SENSOR
1110 AIN0 AIN1
+(AIN2)
-(AIN3) +(AIN4)
-(AIN5) +(AIN6)
-(AIN7) TEMP
SENSOR
1111 +(AIN0)
-(AIN1) +(AIN2)
-(AIN3) +(AIN4)
-(AIN5) +(AIN6)
-(AIN7) TEMP
SENSOR
Bits7-4: UNUSED. Read = 0000b; Write = don’t care
Bits3-0: AMXAD3-0: AMUX Address Bits
0000-1111: ADC Inputs selected per chart below
A
M
X
0
C
F
B
I
T
S
3
-
0
Rev. 1.7 44
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 6.6. ADC0CF: ADC Configuration Register (C8051F01x)
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
ADCSC2 ADCSC1 ADCSC0 - - AMPGN2 AMPGN1 AMPGN0
01100000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xBC
Bits7-5: ADCSC2-0: ADC SAR Conversion Clock Period Bits
000: SAR Conversion Clock = 1 System Clock
001: SAR Conversion Clock = 2 System Clocks
010: SAR Conversion Clock = 4 System Clocks
011: SAR Conversion Clock = 8 System Clocks
1xx: SAR Conversion Clock = 16 Systems Clocks
(Note: Conversion clock should be 2MHz.)
Bits4-3: UNUSED. Read = 00b; Write = don’t care
Bits2-0: AMPGN2-0: ADC Internal Amplifier Gain
000: Gain = 1
001: Gain = 2
010: Gain = 4
011: Gain = 8
10x: Gain = 16
11x: Gain = 0.5
45 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 6.7. ADC0CN: ADC Control Register (C8051F01x)
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
ADCEN ADCTM ADCINT ADBUSY ADSTM1 ADSTM0 ADWINT ADLJST 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
(bit addressable) 0xE8
Bit7: ADCEN: ADC En able Bit
0: ADC Disabled. ADC is in low power shutdown.
1: ADC Enabled. ADC is active and ready for data conversions.
Bit6: ADCTM: ADC Track Mode Bit
0: When the ADC is enabled, tracking is always done unless a conversion is in process
1: Tracking Defined by ADSTM1-0 bits
ADSTM1-0:
00: Tracking starts with the write of 1 to ADBUSY and lasts for 3 SAR clocks
01: Tracking started by the overflow of Timer 3 and last for 3 SAR clocks
10: ADC tracks only when CNVSTR input is logic low
11: Tracking started by the overflow of Timer 2 and last for 3 SAR clocks
Bit5: ADCINT: ADC Conversion Complete Interrupt Flag
(Must be cleared by software)
0: ADC has not completed a data conversion since the last time this flag was cleared
1: ADC has completed a data conversion
Bit4: ADBUSY: ADC Busy Bit
Read
0: ADC Conversion complete or no valid data has been converted since a reset. The falling
edge of ADBUSY generates an interrupt when enabled.
1: ADC Busy converting data
Write
0: No effect
1: Starts ADC Conversion if ADSTM1-0 = 00b
Bits3-2: ADSTM1-0: ADC Start of Conversion Mode Bits
00: ADC conversion started upon every write of 1 to ADBUSY
01: ADC conversions taken on every overflow of Timer 3
10: ADC conversion started upon every rising edge of CNVSTR
11: ADC conversions taken on every overflow of Timer 2
Bit1: ADWINT: ADC Window Compare Interrupt Flag
(Must be cleared by software)
0: ADC Window Comparison Data match has not occurred
1: ADC Window Comparison Data match occurred
Bit0: ADLJST: ADC Left Ju stify Data Bit
0: Data in ADC0H:ADC0L Registers is right justified
1: Data in ADC0H:ADC0L Registers is left justified
Rev. 1.7 46
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 6.8. ADC0H: ADC Data Word MSB Register (C8051F01x)
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xBF
Figure 6.9. ADC0L: ADC Data Word LSB Register (C8051F01x)
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xBE
NOTE: Resulting 10-bit ADC Data Word appears in the ADC Data Word Registers as follows:
ADC0H[1:0]:ADC0L[7:0], if ADLJST = 0
(ADC0H[7:2] will be sign extension of ADC0H.1 if a differential reading, otherwise = 000000b)
ADC0H[7:0]:ADC0L[7:6], if ADLJST = 1
(ADC0L[5:0] = 000000b)
EXAMPLE: ADC Data Word Conversion Map, AIN0 Input in Single-Ended Mode
(AMX0CF=0x00, AMX0SL=0x00)
AIN0 – AGND
(Volts) ADC0H:ADC0L
(ADLJST = 0) ADC0H:ADC0L
(ADLJST = 1)
REF x (1023/1024) 0x03FF 0xFFC0
REF x ½ 0x0200 0x8000
REF x (511/1024) 0x01FF 0x7FC0
0 0x0000 0x0000
EXAMPLE: ADC Data Word Conversion Map, AIN0-AIN1 Differential Input Pair
(AMX0CF=0x01, AMX0SL=0x00)
AIN0 – AIN1 (Volts) ADC0H:ADC0L
(ADLJST = 0) ADC0H:ADC0L
(ADLJST = 1)
REF x (511/512) 0x01FF 0x7FC0
0 0x0000 0x0000
-REF x (1/512) 0xFFFF 0xFFC0
-REF 0xFE00 0x8000
Bits7-0: ADC Data Word Bits
For ADLJST = 1: Upper 8-bits of the 10-bit ADC Data Word.
For ADLJST = 0: Bits7-2 are the sign extension of Bit1. Bits 1-0 are the upper 2-bits of the
10-bit ADC Data Word.
Bits7-0: ADC Data Word Bits
For ADLJST = 1: Bits7-6 are the lower 2- bits of the 10-bit ADC Data Word. Bits5-0 will
always read 0.
For ADLJST = 0: Bits7-0 are the lower 8-bits of the 10-bit ADC Data Word.
47 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
6.3. ADC Programmable Window Detector
The ADC programmable window detector is very useful in many applications. It continuously compares the ADC
output to user-programmed limits and notifies the system when an out-of-band condition is detected. This is
especially effective in an interrupt-driven system, saving code space and CPU bandwidth while delivering faster
system response times. The window detector interrupt flag (ADWINT in ADC0CN) can also be used in polled
mode. The high and low bytes of the reference words are loaded into the ADC Greater-Than and ADC Less-Than
registers (ADC0GTH, ADC0GTL, ADC0LTH, and ADC0LTL). Figure 6.14 and Figure 6.15 show example
comparisons for reference. Notice that the window detector flag can be asserted when the measured data is inside
or outside the user-programmed limits, depending on the programming of the ADC0GTx and ADC0LTx registers.
Figure 6.10. ADC0GTH: ADC Greater-Than Data High Byte Register (C8051F01x)
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
11111111
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xC5
Figure 6.11. ADC0GTL: ADC Greater-Than Data Low Byte Register (C8051F01x)
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
11111111
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xC4
Figure 6.12. ADC0LTH: ADC Less-Than Data High Byte Register (C8051F01x)
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xC7
Figure 6.13. ADC0LTL: ADC Less-Than Data Low Byte Register (C8051F01x)
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xC6
Bits7-0:
The high byte of the ADC Greater-Than Data Word.
Bits7-0:
The low byte of the ADC Greater-Than Data Word.
Definition:
ADC Greater-Than Data Word = ADC0GTH:ADC0GTL
Bits7-0:
The high byte of the ADC Less-Than Data Word.
Bits7-0:
These bits are the low byte of the ADC Less-Than Data Word.
Definition:
ADC Less-Than Data Word = ADC0LTH:ADC0LTL
Rev. 1.7 48
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 6.14. 10-Bit ADC Window Interrupt Examples, Right Justified Data
0x03FF
0x0201
0x0200
0x01FF
0x0101
0x0100
0x00FF
0x0000
ADWINT=1
ADWINT
not affected
ADWINT
not affected
ADC Data
Word
0x03FF
0x0201
0x0200
0x01FF
0x0101
0x0100
0x00FF
0x0000
ADWINT=1
ADWINT
not affected
ADWINT=1
ADC0LTH:ADC0LTL
ADC0GTH:ADC0GTL
ADC Data
Word
ADC0GTH:ADC0GTL
ADC0LTH:ADC0LTL
0
Input Voltage
(AD0 - AGND)
REF x (1023/1024)
REF x (256/1024)
REF x (512/1024)
0
Input Voltage
(AD0 - AGND)
REF x (1023/1024)
REF x (256/1024)
REF x (512/1024)
0x01FF
0x0101
0x0100
0x00FF
0x0000
0xFFFF
0xFFFE
0xFE00
ADWINT=1
ADWINT
not affected
ADWINT
not affected
0x01FF
0x0101
0x0100
0x00FF
0x0000
0xFFFF
0xFFFE
0xFE00
ADWINT=1
ADWINT
not affected
-REF
Input Voltage
(AD0 - AD1)
ADWINT=1
REF x (511/512)
ADC0LTH:ADC0LTL
ADC0GTH:ADC0GTL
ADC Data
Word
ADC Data
Word
ADC0LTH:ADC0LTL
ADC0GTH:ADC0GTL
REF x (256/512)
REF x (-1/512)
-REF
Input Voltage
(AD0 - AD1)
REF x (511/512)
REF x (256/512)
REF x (-1/512)
Given:
AMX0SL = 0x00, AMX0CF = 0x00, ADLJST = 0,
ADC0LTH:ADC0LTL = 0x0200,
ADC0GTH:ADC0GTL = 0x0100.
An ADC End of Conversion will cause an ADC Window
Compare Interrupt (ADWINT=1) if the resulting ADC
Data Word is < 0x0200 and > 0x0100.
Given:
AMX0SL = 0x00, AMX0CF = 0x00, ADLJST = 0,
ADC0LTH:ADC0LTL = 0x0100,
ADC0GTH:ADC0GTL = 0x0200.
An ADC End of Conversion will cause an ADC Window
Compare Interrupt (ADWINT=1) if the resulting ADC
Data Word is < 0x0100 or > 0x0200.
Given:
AMX0SL = 0x00, AMX0CF = 0x01, ADLJST = 0,
ADC0LTH:ADC0LTL = 0x0100,
ADC0GTH:ADC0GTL = 0xFFFF.
An ADC End of Conversion will cause an ADC Window
Compare Interrupt (ADWINT=1) if the resulting ADC
Data Word is < 0x0100 and > 0xFFFF. (Two’s
Complement math, 0xFFFF = -1.)
Given:
AMX0SL = 0x00, AMX0CF = 0x01, ADLJST = 0,
ADC0LTH:ADC0LTH = 0xFFFF,
ADC0GTH:ADC0GTL = 0x0100.
An ADC End of Conversion will cause an ADC Window
Compare Interrupt (ADWINT=1) if the resulting ADC
Data Word is < 0xFFFF or > 0x0100. (Two’s Complement
math, 0xFFFF = -1.)
49 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 6.15. 10-Bit ADC Window Interrupt Examples, Left Justified Data
0xFFC0
0x8040
0x8000
0x7FC0
0x4040
0x4000
0x3FC0
0x0000
ADWINT=1
ADWINT
not affected
ADWINT
not affected
ADC Data
Word
0xFFC0
0x8040
0x8000
0x7FC0
0x4040
0x4000
0x3FC0
0x0000
ADWINT=1
ADWINT
not affected
ADWINT=1
ADC0LTH:ADC0LTL
ADC0GTH:ADC0GTL
ADC Data
Word
ADC0GTH:ADC0GTL
ADC0LTH:ADC0LTL
0
Input Voltage
(AD0 - AGND)
REF x (1023/1024)
REF x (256/1024)
REF x (512/1024)
0
Input Voltage
(AD0 - AGND)
REF x (1023/1024)
REF x (256/1024)
REF x (512/1024)
Given:
AMX0SL = 0x00, AMX0CF = 0x00, ADLJST = 1,
ADC0LTH:ADC0LTL = 0x8000,
ADC0GTH:ADC0GTL = 0x4000.
An ADC End of Conversion will cause an ADC Window
Compare Interrupt (ADWINT=1) if the resulting ADC
Data Word is < 0x8000 and > 0x4000.
Given:
AMX0SL = 0x00, AMX0CF = 0x00, ADLJST = 1,
ADC0LTH:ADC0LTL = 0x4000,
ADC0GTH:ADC0GTL = 0x8000.
An ADC End of Conversion will cause an ADC Window
Compare Interrupt (ADWINT=1) if the resulting ADC
Data Word is < 0x4000 or > 0x8000.
Given:
AMX0SL = 0x00, AMX0CF = 0x01, ADLJST = 1,
ADC0LTH:ADC0LTL = 0x2000,
ADC0GTH:ADC0GTL = 0xFFC0.
An ADC End of Conversion will cause an ADC Window
Compare Interrupt (ADWINT=1) if the resulting ADC
Data Word is < 0x2000 and > 0xFFC0. (Two’s
Complement mat h . )
Given:
AMX0SL = 0x00, AMX0CF = 0x01, ADLJST = 1,
ADC0LTH:ADC0LTH = 0xFFC0,
ADC0GTH:ADC0GTL = 0x2000.
An ADC End of Conversion will cause an ADC Window
Compare Interrupt (ADWINT=1) if the resulting ADC
Data Word is < 0xFFC0 or > 0x2000. (Two’s Complement
math.)
0x7FC0
0x2040
0x2000
0x1FC0
0x0000
0xFFC0
0xFF80
0x8000
ADWINT=1
ADWINT
not affected
ADWINT
not affected
0x7FC0
0x2040
0x2000
0x1FC0
0x0000
0xFFC0
0xFF80
0x8000
ADWINT=1
ADWINT
not affected
-REF
Input Voltage
(AD0 - AD1)
ADWINT=1
REF x (511/512)
ADC0LTH:ADC0LTL
ADC0GTH:ADC0GTL
ADC Data
Word
ADC Data
Word
ADC0LTH:ADC0LTL
ADC0GTH:ADC0GTL
REF x (128/512)
REF x (-1/512)
-REF
Input Voltage
(AD0 - AD1)
REF x (511/512)
REF x (128/512)
REF x (-1/512)
Rev. 1.7 50
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Table 6.1. 10-Bit ADC Electrical Characteristics
VDD = 3.0V, AV+ = 3.0V, VREF = 2.40V (REFBE=0), PGA Gain = 1, -40C to +85C unless otherwise specified.
PARAMETER CONDITIONS MIN TYP MAX UNITS
DC ACCURACY
Resolution 10 bits
Integral Nonlinearity ½ 1 LSB
Differential Nonlinearity Guaranteed Monotonic ½ 1 LSB
Offset Error 0.5 LSB
Full Scale Error Differential mode -1.5
0.5 LSB
Offset Temperature
Coefficient
0.25 ppm/C
DYNAMIC PERFORMANCE (10kHz sine-wave input, 0 to –1dB of full scale, 100ksps)
Signal-to-Noise Plus
Distortion 59 61 dB
Total Harmonic Distortion Up to the 5th harmonic -70 dB
Spurious-Free Dynamic
Range 80 dB
CONVERSION RATE
Conversion Time in SAR
Clocks 16 clocks
SAR Clock Frequency C8051F000, ‘F001, ‘F002
C8051F005, ‘F006, ‘F007 2.0
2.5 MHz
MHz
Track/Hold Acquisition
Time 1.5
s
Throughput Rate 100 ksps
ANALOG INPUTS
Voltage Conversion Range Single-ended Mode (AINn – AGND)
Differential Mode |(AINn+) – (AINm-)| 0 VREF
- 1LSB V
Input Voltage Any AINn pin AGND AV+ V
Input Capacitance 10 pF
TEMPERATURE SENSOR
Linearity
0.20 C
Absolute Accuracy 3 C
Gain PGA Gain = 1 2.86 mV/C
Gain Error (1) PGA Gain = 1 33.5 V/C
Offset PGA Gain = 1, Temp = 0C 776 mV
Offset Error (1) PGA Gain = 1, Temp = 0C 8.51 mV
POWER SPECIFICATIONS
Power Supply Current (AV+
supplied to ADC) Operating Mode, 100ksps 450 900 A
Power Supply Rejection 0.3 mV/V
51 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
7. DACs, 12 BIT VOLTAGE MODE
The C8051F000 MCU family has two 12-bit voltage-mode Digital to Analog Converters. Each DAC has an output
swing of 0V to VREF-1LSB for a corresponding input code range of 0x000 to 0xFFF. Using DAC0 as an example,
the 12-bit data word is written to the lo w byte (DAC0L) and h igh byte (DAC0H) data registers. Data is latched into
DAC0 after a write to the corresponding DAC0H register, so the write sequence should be DAC0L followed by
DAC0H if the full 12-bit resolutio n is required. The DAC can be used in 8-b it mode by initializing DAC0L to the
desired value (typically 0x00), and writing data to only DAC0H with the data shifted to the left. DAC0 Control
Register (DAC0CN) provides a means to enable/disable DAC0 and to modify its input data formatting.
The DAC0 enable/disable function is controlled by the DAC0EN bit (DAC0CN.7). Writing a 1 to DAC0EN
enables DAC0 while writing a 0 to DAC0EN disables DAC0. While disabled, the output of DAC0 is maintained in
a high-impedance state, and the DAC0 supply current falls to 1A or less. Also, the Bias Enable bit (BIASE) in the
REF0CN register (see Figure 9.2) must be set to 1 in order to supply bias to DAC0. The voltage reference for
DAC0 must also be set properly (see Section 9).
In some instances, input data should be shifted prior to a DAC0 write operation to properly justify data within the
DAC input registers. This action would typically require one or more load and shift operations, adding software
overhead and slowing DAC throughput. To alleviate this problem, the data-formatting feature provides a means for
the user to program the orientation of the DAC0 data word within data registers DAC0H and DAC0L. The three
DAC0DF bits (DAC0CN.[2:0]) allow the user to specify one of five data word orientations as shown in the
DAC0CN register definition.
DAC1 is functionally the same as DAC0 described above. The electrical specifications for both DAC0 and DAC1
are given in Table 7.1.
Figure 7.1. DAC Functional Block Diagram
DAC0
+
-
AV+
12
AGND
8
8
REF
DAC0
DAC0CN
DAC0EN
DAC0DF2
DAC0DF1
DAC0DF0
DAC0HDAC0L
Dig. MUX
DAC1
+
-
AV+
12
AGND
8
8
REF
DAC1
DAC1CN
DAC1EN
DAC1DF2
DAC1DF1
DAC1DF0
DAC1HDAC1L
Dig. MUX
Rev. 1.7 52
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 7.2. DAC0H: DAC0 High Byte Register
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xD3
Figure 7.3. DAC0L: DAC0 Low Byte Register
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xD2
Figure 7.4. DAC0CN: DAC0 Control Register
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
DAC0EN - - - -
DAC0DF2 DAC0DF1 DAC0DF0 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xD4
Bits7-0: DAC0 Data Word Most Significant Byte.
Bits7-0: DAC0 Data Word Least Significant Byte.
Bit7: DAC0 EN: DAC0 Enable Bit
0: DAC0 Disabled. DAC0 Output pin is disabled; DAC0 is in low power shutdown mode.
1: DAC0 Enabled. DAC0 Output is pin active; DAC0 is operational.
Bits6-3: UNUSED. Read = 0000b; Write = don’t care
Bits2-0: DAC0DF2-0: DAC0 Data Format Bits
000: The most significant nybble of the DAC0 Data Word is in DAC0H[3:0], while the least significant
byte is in DAC0L.
DAC0H DAC0L
MSB LSB
001: The most significant 5-bits of the DAC0 Data Word is in DAC0H[4:0], while the least significant
7-bits is in DAC0L[7:1].
DAC0H DAC0L
MSB LSB
010: The most significant 6-bits of the DAC0 Data Word is in DAC0H[5:0], while the least significant
6-bits is in DAC0L[7:2].
DAC0H DAC0L
MSB LSB
011: The most significant 7-bits of the DAC0 Data Word is in DAC0H[6:0], while the least significant
5-bits is in DAC0L[7:3].
DAC0H DAC0L
MSB LSB
1xx: The most significant byte of the DAC0 Data Word is in DAC0H, while the least significant nybble
is in DAC0L[7:4].
DAC0H DAC0L
MSB LSB
53 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 7.5. DAC1H: DAC1 High Byte Register
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xD6
Figure 7.6. DAC1L: DAC1 Low Byte Register
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xD5
Figure 7.7. DAC1CN: DAC1 Control Register
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
DAC1EN - - - - DAC1DF2 DAC1DF1 DAC1DF0
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xD7
Bits7-0: DAC1 Data Word Most Significant Byte.
Bits7-0: DAC1 Data Word Least Significant Byte.
Bit7: DAC1 EN: DAC1 Enable Bit
0: DAC1 Disabled. DAC1 Output pin is disabled; DAC1 is in low power shutdown mode.
1: DAC1 Enabled. DAC1 Output is pin active; DAC1 is operational.
Bits6-3: UNUSED. Read = 0000b; Write = don’t care
Bits2-0: DAC1DF2-0: DAC1 Data Format Bits
000: The most significant nybble of the DAC1 Data Word is in DAC1H[3:0], while the least
significant byte is in DAC1L.
DAC1H DAC1L
MSB LSB
001: The most significant 5-bits of the DAC1 Data Word is in DAC1H[4:0], while the least
significant 7-bits is in DAC1 L[7:1].
DAC1H DAC1L
MSB LSB
010: The most significant 6-bits of the DAC1 Data Word is in DAC1H[5:0], while the least
significant 6-bits is in DAC1 L[7:2].
DAC1H DAC1L
MSB LSB
011: The most significant 7-bits of the DAC1 Data Word is in DAC1H[6:0], while the least
significant 5-bits is in DAC1 L[7:3].
DAC1H DAC1L
MSB LSB
1xx: The most significant byte of the DAC1 Data Word is in DAC1H, while the least
significant nybble is in DAC1L[7:4].
DAC1H DAC1L
MSB LSB
Rev. 1.7 54
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Table 7.1. DAC Electrical Characteristics
VDD = 3.0V, AV+ = 3.0V, REF = 2.40V (REFBE=0), No Output Load unless otherwise specified.
PARAMETER CONDITIONS MIN TYP MAX UNITS
STATIC PERFORMANCE
Resolution 12 bits
Integral Nonlinearity For Data Word Range 0x014 to 0xFEB 2 LSB
Differential Nonlinearity Guaranteed Monotonic (codes 0x014 to
0xFEB)
1 LSB
Output Noise No Output Filter
100kHz Output Filter
10kHz Output Filter
250
128
41
Vrms
Offset Error Data Word = 0x014 3 30 mV
Offset Tempco 6
ppm/C
Full-Scale Error 20 60 mV
Full-Scale Error Tempco 10 ppm/C
VDD Power-Supply
Rejection Ratio -60 dB
Output Impedance in
Shutdown Mode DACnEN=0 100 k
Output Current
300 A
Output Short Circuit Current Data Word = 0xFFF 15 mA
DYNAMIC PERFORMANCE
Voltage Output Slew Rate Load = 40pF 0.44 V/s
Output Settling Time To ½
LSB Load = 40pF, Output swing from code
0xFFF to 0x014 10 s
Output Voltage Swing 0 REF-
1LSB V
Startup Time DAC Enable asserted 10 s
ANALOG OUTPUTS
Load Regulation IL = 0.01mA to 0.3mA at code 0xFFF 60 ppm
CURRENT CONSUMPTION (each DAC)
Power Supply Current (AV+
supplied to DAC) Data Word = 0x7FF 110 400 A
55 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
8. COMPARATORS
The MCU family has two on-chip analog voltage comparators as shown in Figure 8.1. The inputs of each
Comparator are available at the package pins. The output of each comparator is optionally available at the package
pins via the I/O crossbar (see Section 15.1). When assigned to package pins, each comparator output can be
programmed to operate in open drain or push-pull modes (see section 15.3).
The hysteresis of each comparator is software-programmable via its respective Comparator control register
(CPT0CN, CPT1CN). The user can program both the amount of hysteresis voltage (referred to the input voltage)
and the positive and negative-going symmetry of this hysteresis around the threshold voltage. The output of the
comparator can be polled in software, or can be used as an interrupt source. Each comparator can be individually
enabled or disabled (shutdown). When disabled, the comparator output (if assigned to a Port I/O pin via the
Crossbar) defaults to the logic low state, its interrupt capability is suspended and its supply current falls to less than
1A. Comparator 0 inputs can be externally driven from -0.25V to (AV+) + 0.25V without damage or upset.
The Comparator 0 hysteresis is programmed using bits 3-0 in the Comparator 0 Control Register CPT0CN (shown
in Figure 8.3). The amount of negative hysteresis voltage is determined by the settings of the CP0HYN bits. As
shown in Figure 8.2, settings of 10, 4 or 2mV of negative hysteresis can be programmed, or negative hysteresis can
be disabled. In a similar way, the amount of positive hysteresis is determined by the setting the CP0HYP bits.
Comparator interrupts can be generated on both rising-edge and falling-edge output transitions. (For Interrupt
enable and priority control, see Section 10.4). The CP0FIF flag is set upon a Comparator 0 falling-edge interrupt,
and the CP0RIF flag is set upon the Comparator 0 rising-edge interrupt. Once set, these bits remain set until cleared
by the CPU. The Output State of Comparator 0 can be obtained at any time by reading the CP0OUT bit. Note the
comparator output and interrupt should be ignored until the comparator settles after power-up. Comparator 0 is
enabled by setting the CP0EN bit, and is disabled by clearing this bit. Note there is a 20usec settling time for the
comparator output to stabilize after setting the CP0EN bit or a power-up. Comparator 0 can also be programmed as
a reset source. For details, see Section 13.
The operation of Comparator 1 is identical to that of Comparator 0, except the Comparator 1 is controlled by the
CPT1CN Register (Figure 8.4). Comparator 1 can not be programmed as a reset source. Also, the input pins for
Comparator 1 are not pinned out on the F002, F007, F012, or F017 devices. The complete electrical specifications
for the Comparators are given in Table 8.1.
Figure 8.1. Comparator Functional Block Diagram
+
-
AV+
Q
Q
SET
CLR
D
Q
Q
SET
CLR
D
Crossbar
Interrupt
Handler
Reset
Decision
Tree
(SYNCHRONIZER)
CP0+
CP0-
AGND
CPT0CN
CP0EN
CP0OUT
CP0RIF
CP0FIF
CP0HYP1
CP0HYP0
CP0HYN1
CP0HYN0
+
-
AV+
Q
Q
SET
CLR
D
Q
Q
SET
CLR
D
Crossbar
Interrupt
Handler
(SYNCHRONIZER)
CP1+
CP1-
AGND
CPT1CN
CP1EN
CP1OUT
CP1RIF
CP1FIF
CP1HYP1
CP1HYP0
CP1HYN1
CP1HYN0
not available on F002,
F007, F012, and F017
Rev. 1.7 56
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 8.2. Comparator Hysteresis Plot
Positive Hysteresis Voltage
(Programmed with CP0HYSP Bits)
Negative Hysteresis Voltage
(Programmed by CP0HYSN Bits)
VIN-
VIN+
INPUTS
CIRCUIT CONFIGURATION
+
_
CP0+
CP0- CP0
VIN+
VIN- OUT
V
OH
Positive Hysteresis
Disabled Maximum
Positive Hysteresis
Negative Hysteresis
Disabled Maximum
Negative Hysteresis
OUTPUT
V
OL
57 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 8.3. CPT0CN: Comparator 0 Control Register
R/W R R/W R/W R/W R/W R/W R/W Reset Value
CP0EN CP0OUT CP0RIF CP0FIF CP0HYP1 CP0HYP0 CP0HYN1 CP0HYN0 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0x9E
Bit7: CP0 E N: Comparator 0 Enable Bit
0: Comparator 0 Disabled.
1: Comparator 0 Enabled.
Bit6: CP0OUT: Comparator 0 Output State Flag
0: Voltage on CP0+ < CP0-
1: Voltage on CP0+ > CP0-
Bit5: CP0RIF: Comparator 0 Rising-Edge Interrupt Flag
0: No Comparator 0 Rising-Edge Interrupt has occurred since this flag was cleared
1: Comparator 0 Rising-Edge Interrupt has occurred since this flag was cleared
Bit4: CP0FIF: Comparator 0 Falling-Edge Interrupt Flag
0: No Comparator 0 Falling-Edge Interrupt has occurred since this flag was cleared
1: Comparator 0 Falling-Edge Interrupt has occurred since this flag was cleared
Bit3-2: CP0HYP1-0: Comparator 0 Positive Hysteresis Control Bits
00: Positive Hysteresis Disabled
01: Positive Hysteresis = 2mV
10: Positive Hysteresis = 4mV
11: Positive Hysteresis = 10mV
Bit1-0: CP0HYN1-0: Comparator 0 Negative Hysteresis Control Bits
00: Negative Hysteresis Disabled
01: Negative Hysteresis = 2mV
10: Negative Hysteresis = 4mV
11: Negative Hysteresis = 10mV
Rev. 1.7 58
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 8.4. CPT1CN: Comparator 1 Control Register
R/W R R/W R/W R/W R/W R/W R/W Reset Value
CP1EN CP1OUT CP1RIF CP1FIF CP1HYP1 CP1HYP0 CP1HYN1 CP1HYN0 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0x9F
Bit7: CP1 E N: Comparator 1 Enable Bit
0: Comparator 1 Disabled.
1: Comparator 1 Enabled.
Bit6: CP1OUT: Comparator 1 Output State Flag
0: Voltage on CP1+ < CP1-
1: Voltage on CP1+ > CP1-
Bit5: CP1RIF: Comparator 1 Rising-Edge Interrupt Flag
0: No Comparator 1 Rising-Edge Interrupt has occurred since this flag was cleared
1: Comparator 1 Rising-Edge Interrupt has occurred since this flag was cleared
Bit4: CP1FIF: Comparator 1 Falling-Edge Interrupt Flag
0: No Comparator 1 Falling-Edge Interrupt has occurred since this flag was cleared
1: Comparator 1 Falling-Edge Interrupt has occurred since this flag was cleared
Bit3-2: CP1HYP1-0: Comparator 1 Positive Hysteresis Control Bits
00: Positive Hysteresis Disabled
01: Positive Hysteresis = 2mV
10: Positive Hysteresis = 4mV
11: Positive Hysteresis = 10mV
Bit1-0: CP1HYN1-0: Comparator 1 Negative Hysteresis Control Bits
00: Negative Hysteresis Disabled
01: Negative Hysteresis = 2mV
10: Negative Hysteresis = 4mV
11: Negative Hysteresis = 10mV
59 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Table 8.1. Comparator Electrical Characteristics
VDD = 3.0V, AV+ = 3.0V, -40C to +85C unless otherwise specified.
PARAMETER CONDITIONS MIN TYP MAX UNITS
Response Time1 (CP+) – (CP-) = 100mV (Note 1) 4 s
Response Time2 (CP+) – (CP-) = 10mV (Note 1) 12 s
Common Mode Rejection
Ratio 1.5 4 mV/V
Positive Hysteresis1 CPnHYP1-0 = 00 0 1 mV
Positive Hysteresis2 CPnHYP1-0 = 01 2 4.5 7 mV
Positive Hysteresis3 CPnHYP1-0 = 10 4 9 13 mV
Positive Hysteresis4 CPnHYP1-0 = 11 10 17 25 mV
Negative Hysteresis1 CPnHYN1-0 = 00 0 1 mV
Negative Hysteresis2 CPnHYN1-0 = 01 2 4.5 7 mV
Negative Hysteresis3 CPnHYN1-0 = 10 4 9 13 mV
Negative Hysteresis4 CPnHYN1-0 = 11 10 17 25 mV
Inverting or Non-inverting
Input Voltage Range -0.25 (AV+)
+ 0.25 V
Input Capacitance 7 pF
Input Bias Current -5 0.001 +5 nA
Input Offset Voltage -10 +10 mV
POWER SUPPLY
Power-up Time CPnEN from 0 to 1 20 s
Power Supply Rejection 0.1 1 mV/V
Supply Current Operating Mode (each comparator) at DC 1.5 10 A
Note 1: CPnHYP1-0 = CPnHYN1-0 = 00.
Rev. 1.7 60
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
9. VOLTAGE REFERENCE
The voltage reference circuit consists of a 1.2V, 15ppm/C (typical) bandgap voltage reference generator and a
gain-of-two output buffer amplifier. The reference voltage on VREF can be connected to external devices in the
system, as long as the maximum load seen by the VREF pin is less than 200A to AGND (see Figure 9.1).
If a different reference voltage is required, an external reference can be connected to the VREF pin and the internal
bandgap and buffer amplifier disabled in software. The external reference voltage must still be less than AV+ -
0.3V. The Reference Control Register, REF0CN (defined in Figure 9.2), provides the means to enable or disable
the bandgap and buffer amplifier. The BIASE bit in REF0CN enables the bias circuitry for the ADC and DACs
while the REFBE bit enables the bandgap reference and buffer amplifier which drive the VREF pin. When
disabled, the supply current drawn by the bandgap and buffer amplifier falls to less than 1uA (typical) and the
output of the buffer amplifier enters a high impedance state. If the internal bandgap is used as the reference voltage
generator, BIASE and REFBE must both be set to 1. If an external reference is used, REFBE must be set to 0 and
BIASE must be set to 1. If neither the ADC nor the DAC are being used, both of these bits can be set to 0 to
conserve power. The electrical specifications for the Voltage Reference are given in Table 9.1.
The temperature sensor connects to the highest order input of the A/D converter’s input multiplexer (see Figure 5.1
and Figure 5.5 for details). The TEMPE bit within REF0CN enables and disables the temperature sensor. While
disabled, the temperature sensor defaults to a high impedance state and any A/D measurements performed on the
sensor while disabled result in meaningless data.
Figure 9.1. Voltage Reference Functional Block Diagram
Bias
Generator
(to ADC
and DAC)
VREF
EN
(to Analog Mux)
RLOAD
AGND
AGND
External Equivalent
Load Circuit
AGND
R1
AV+ External
Voltage
Reference
Circuit
Temp
Sensor
EN
200uA
(max)
(Bias to ADC
and DAC)
REF0CN
TEMPE
BIASE
REFBE
2.4V
Reference
EN
AGND
61 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 9.2. REF0CN: Reference Control Register
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
- - - - - TEMPE BIASE REFBE 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xD1
Table 9.1. Reference Electrical Characteristics
VDD = 3.0V, AV+ = 3.0V, -40C to +85C unless otherwise specified.
PARAMETER CONDITIONS MIN TYP MAX UNITS
INTERNAL REFERENCE (REFBE = 1)
Output Voltage 25C ambient 2.34 2.43 2.50 V
VREF Short Circuit Current 30 mA
VREF Power Supply
Current (supplied by AV+) 50 A
VREF Temperature
Coefficient 15
ppm/C
Load Regulation Load = (0-to-200A) to AGND (Note 1) 0.5
ppm/A
VREF Turn-on Time1 4.7F tantalum, 0.1F ceramic bypass 2 ms
VREF Turn-on Time2 0.1F ceramic bypass 20 s
VREF Turn-on Time3 no bypass cap 10 s
EXTERNAL REFERENCE (REFBE = 0)
Input Voltage Range 1.00 (AV+)
– 0.3V V
Input Current 0 1 A
Note 1: The reference can only source current. When driving an external load, it is recommended to add a load
resistor to AGND.
Bits7-3: UNUSED. Read = 00000b; Write = don’t care
Bit2: TEMPE: Temperature Sensor Enable Bit
0: Internal Temperature Sensor Off.
1: Internal Temperature Sensor On.
Bit1: BIASE: Bias Enable Bit for ADC and DAC’s
0: Internal Bias Off.
1: Internal Bias On (required for use of ADC or DAC’s).
Bit0: REFBE: Internal Voltage Reference Buffer Enable Bit
0: Internal Reference Buffer Off. System reference can be driven from external source on
VREF pin.
1: Internal Reference Buffer On. System reference provided by internal voltage reference.
Rev. 1.7 62
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
10. CIP-51 CPU
The MCUs’ system CPU is the CIP-51. The CIP-51 is fully compatible with the MCS-51TM instruction set.
Standard 803x/805x assemblers and compilers can be used to develop software. The MCU family has a superset of
all the peripherals included with a standard 8051. Included are four 16-bit counter/timers (see description in Section
19), a full-duplex UART (see description in Section 18), 256 bytes of internal RAM, 128 byte Special Function
Register (SFR) address space (see Section 10.3), and four byte-wide I/O Ports (see description in Section 14). The
CIP-51 also includes on-chip debug hardware (see description in Section 21), and interfaces directly with the
MCUs’ analog and digital subsystems providing a complete data acquisition or control-system solution in a single
integrated circuit.
Features
The CIP-51 Microcontroller core implements the standard 8051 organization and peripherals as well as additional
custom peripherals and functions to extend its capability (see Figure 10.1 for a block diagram). The CIP-51
includes the following features:
Figure 10.1. CIP-51 Block Diagram
DATA BUS
TMP1 TMP2
PRGM. ADDRESS REG.
PC INCREMENTER
ALU
PSW
DATA BUS
DATA BUS
MEMORY
INTERFACE
MEM_ADDRESS
D8
PIPELINE
BUFFER
DATA POINTER
INTERRUPT
INTERFACE
SYSTEM_IRQs
EMULATION_IRQ
MEM_CONTROL
CONTROL
LOGIC
A16
PROGRAM COUNTER (PC)
STOP
CLOCK
RESET
IDLE POWER CONTROL
REGISTER
DATA BUS
SFR
BUS
INTERFACE
SFR_ADDRESS
SFR_CONTROL
SFR_WRITE_DATA
SFR_READ_DATA
D8
D8
B REGISTER
D8
D8
ACCUMULATOR
D8
D8
D8
D8
D8
D8
D8
D8
MEM_WRITE_DATA
MEM_READ_DATA
D8
SRAM
ADDRESS
REGISTER
SRAM
(256 X 8)
D8
STACK POINTER
D8
- Reset Input
- Power Management Modes
- On-chip Debug Circuitry
- Program and Data Memory Security
- Fully Compatible with MCS-51 Instruction Set
- 25 MIPS Peak Throughput with 25MHz Clock
- 0 to 25MHz Clock Frequency (on ‘F0x5/6/7)
- Four Byte-Wide I/O Ports
- Extended Interrupt Handler
63 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Performance
The CIP-51 employs a pipelined architecture that greatly increases its instruction throughput over the standard 8051
architecture. In a standard 8051, all instructions except for MUL and DIV take 12 or 24 system clock cycles to
execute, and usually have a maximum system clock of 12MHz. By contrast, the CIP-51 core executes 70% of its
instructions in one or two system clock cycles, with no instructions taking more than eight system clock cycles.
With the CIP-51’s maximum system clock at 25MHz, it has a peak throughput of 25MIPS. The CIP-51 has a total
of 109 instructions. The number of instructions versus the system clock cycles required to execute them is as
follows:
Instructions 26 50 5 14 7 3 1 2 1
Clocks to Execute 1 2 2/3 3 3/4 4 4/5 5 8
Programming and Debugging Support
A JTAG-based serial interface is provided for in-system programming of the Flash program memory and
communication with on-chip debug support circuitry. The reprogrammable Flash can also be read and changed a
single byte at a time by the application software using the MOVC and MOVX instructions. This feature allows
program memory to be used for non-volatile data storage as well as updating program code under software control.
The on-chip debug support circuitry facilitates full speed in-circuit debugging, allowing the setting of hardware
breakpoints and watch points, starting, stopping and single stepping through program execution (including interrupt
service routines), examination of the program’s call stack, and reading/writing the contents of registers and memory.
This method of on-chip debugging is completely non-intrusive and non-invasive, requiring no RAM, Stack, timers,
or other on-chip resources.
The CIP-51 is supported by development tools from Silicon Laboratories and third party vendors. Silicon Labs
provides an integrated development environment (IDE) including editor, macro assembler, debugger and
programmer. The IDE’s debugger and programmer interface to the CIP-51 via its JTAG interface to provide fast
and efficient in-system device programming and debugging. Third party macro assemblers and C compilers are also
available.
10.1. INSTRUCTION SET
The instruction set of the CIP-51 System Controller is fully compatible with th e standard MCS-51 ™ instruction set.
Standard 8051 development tools can be used to develop software for the CIP-51. All CIP-51 instructions are the
binary and functional equivalent of their MCS-51™ counterparts, including opcodes, addressing modes and effect
on PSW flags. However, instruction timing is different than that of the standard 8051.
10.1.1. Instruction and CPU Timing
In many 8051 implementations, a distinction is made between machine cycles and clock cycles, with machine cycles
varying from 2 to 12 clock cycles in length. However, the CIP-51 implementation is based solely on clock cycle
timing. All instruction timings are specified in terms of clock cycles.
Due to the pipelined architecture of the CIP-51, most instructions execute in the same number of clock cycles as
there are program bytes in the instruction. Conditional branch instructions take one less clock cycle to complete
when the branch is not taken as opposed to when the branch is taken. Table 10.1 is the CIP-51 Instruction Set
Summary, which includes the mnemonic, number of bytes, and number of clock cycles for each instruction.
10.1.2. MOVX Instruction and Program Memory
The MOVX instruction is typically used to access external data memory. In the CIP-51, the MOVX instruction can
access the on-chip program memory space implemented as reprogrammable Flash memory using the control bits in
the PSCTL register (see Figure 11.1). This feature provides a mechanism for the CIP-51 to update program code
and use the program memory space for non-volatile data storage. For the products with RAM mapped into external
data memory space (C8051F005/06/07/15/16/17), MOVX is still used to read/write this memory with the PSCTL
Rev. 1.7 64
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
register configured for accessing the external data memory space. Refer to Section 11 (Flash Memory) for further
details.
65 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Table 10.1. CIP-51 Instruction Set Summary
Mnemonic Description Bytes Clock
Cycles
ARITHMETIC OPERATIONS
ADD A,Rn Add register to A 1 1
ADD A,direct Add direct byte to A 2 2
ADD A,@Ri Add indirect RAM to A 1 2
ADD A,#data Add immediate to A 2 2
ADDC A,Rn Add register to A with carry 1 1
ADDC A,direct Add direct byte to A with carry 2 2
ADDC A,@Ri Add indirect RAM to A with carry 1 2
ADDC A,#data Add immediate to A with carry 2 2
SUBB A,Rn Subtract register from A with borrow 1 1
SUBB A,direct Subtract direct byte from A with borrow 2 2
SUBB A,@Ri Subtract indirect RAM from A with borrow 1 2
SUBB A,#data Subtract immediate from A with borrow 2 2
INC A Increment A 1 1
INC Rn Increment register 1 1
INC direct Increment direct byte 2 2
INC @Ri Increment indirect RAM 1 2
DEC A Decrement A 1 1
DEC Rn Decrement register 1 1
DEC direct Decrement direct byte 2 2
DEC @Ri Decrement indirect RAM 1 2
INC DPTR In crement Data Pointer 1 1
MUL AB Multiply A and B 1 4
DIV AB Divide A by B 1 8
DA A Decimal Adjust A 1 1
LOGICAL OPERATIONS
ANL A,Rn AND Register to A 1 1
ANL A,direct AND direct byte to A 2 2
ANL A,@Ri AND indirect RAM to A 1 2
ANL A,#data AND immediate to A 2 2
ANL direct,A AND A to direct byte 2 2
ANL direct,#data AND immediate to direct byte 3 3
ORL A,Rn OR Register to A 1 1
ORL A,direct OR direct byte to A 2 2
ORL A,@Ri OR indirect RAM to A 1 2
ORL A,#data OR immediate to A 2 2
ORL direct,A OR A to direct byte 2 2
ORL direct,#data OR immediate to direct byte 3 3
XRL A,Rn Exclusive-OR Register to A 1 1
XRL A,direct Exclusive-OR direct byte to A 2 2
XRL A,@Ri Exclusive-OR indirect RAM to A 1 2
XRL A,#data Exclusive-OR immediate to A 2 2
XRL direct,A Exclusive-OR A to direct byte 2 2
XRL direct,#data Exclusive-OR immediate to direct byte 3 3
CLR A Clear A 1 1
CPL A Complement A 1 1
RL A Rotate A left 1 1
RLC A Rotate A left through carry 1 1
Rev. 1.7 66
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Mnemonic Description Bytes Clock
Cycles
RR A Rotate A right 1 1
RRC A Rotate A right through carry 1 1
SWAP A Swap nibbles of A 1 1
DATA TRANSFER
MOV A,Rn Move register to A 1 1
MOV A,direct Move direct byte to A 2 2
MOV A,@Ri Move indirect RAM to A 1 2
MOV A,#data Move immediate to A 2 2
MOV Rn,A Move A to register 1 1
MOV Rn,direct Move direct byte to register 2 2
MOV Rn,#data Move immediate to register 2 2
MOV direct,A Move A to direct byte 2 2
MOV direct,Rn Move register to direct byte 2 2
MOV direct,direct Move direct byte to direct 3 3
MOV direct,@Ri Move indirect RAM to direct byte 2 2
MOV direct,#data Move immediate to direct byte 3 3
MOV @Ri,A Move A to indirect RAM 1 2
MOV @Ri,direct Move direct byte to indirect RAM 2 2
MOV @Ri,#data Move immediate to indirect RAM 2 2
MOV DPTR,#data16 Load data pointer with 16-bit constant 3 3
MOVC A,@A+DPTR Move code byte relative DPTR to A 1 3
MOVC A,@A+PC Move code byte relative PC to A 1 3
MOVX A,@Ri Move external data (8-bit address) to A 1 3
MOVX @Ri,A Move A to external data (8-bit address) 1 3
MOVX A,@DPTR Move external data (16-bit address) to A 1 3
MOVX @DPTR,A Move A to external data (16-bit address) 1 3
PUSH direct Push direct byte onto stack 2 2
POP direct Pop direct byte from stack 2 2
XCH A,Rn Exchange register with A 1 1
XCH A,direct Exchange direct byte with A 2 2
XCH A,@Ri Exchange indirect RAM with A 1 2
XCHD A,@Ri Exchange low nibble of indirect RAM with A 1 2
BOOLEAN MANIPULATION
CLR C Clear carry 1 1
CLR bit Clear direct bit 2 2
SETB C Set carry 1 1
SETB bit Set direct bit 2 2
CPL C Complement carry 1 1
CPL bit Complement direct bit 2 2
ANL C,bit AND direct bit to carry 2 2
ANL C,/bit AND complement of direct bit to carry 2 2
ORL C,bit OR d irect b it to carry 2 2
ORL C,/bit OR complement of direct bit to carry 2 2
MOV C,bit Move direct bit to carry 2 2
MOV bit,C Move carry to direct bit 2 2
JC rel Jump if carry is set 2 2/3
JNC rel Jump if carry not set 2 2/3
JB bit,rel Jump if direct bit is set 3 3/4
JNB bit,rel Jump if direct bit is not set 3 3/4
JBC bit,rel Jump if direct bit is set and clear bit 3 3/4
67 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Mnemonic Description Bytes Clock
Cycles
PROGRAM BRANCHING
ACALL addr11 Absolute subroutine call 2 3
LCALL addr16 Long subroutine call 3 4
RET Return from subroutine 1 5
RETI Return from interrupt 1 5
AJMP addr11 Absolute jump 2 3
LJMP addr16 Long jump 3 4
SJMP rel Short jump (relative address) 2 3
JMP @A+DPTR Jump indirect relative to DPTR 1 3
JZ rel Jump if A equals zero 2 2/3
JNZ rel Jump if A does not equal zero 2 2/3
CJNE A,direct,rel Compare direct byte to A and jump if not equal 3 3/4
CJNE A,#data,rel Compare immediate to A and jump if not equal 3 3/4
CJNE Rn,#data,rel Compare immediate to register and jump if not
equal 3 3/4
CJNE @Ri,#data,rel Compare immediate to indirect and jump if not
equal 3 4/5
DJNZ Rn,rel Decrement register and jump if not zero 2 2/3
DJNZ direct,rel Decrement direct byte and jump if not zero 3 3/4
NOP No operation 1 1
Notes on Registers, Oper a nds and Addr e ssing Modes:
Rn - Register R0-R7 of the currently selected register bank.
@Ri - Data RAM location addressed indirectly through register R0-R1
rel - 8-bit, signed (two’s compliment) offset relative to the first byte of the following instruction. Used by SJMP
and all conditional jumps.
direct - 8-bit internal data location’s address. This could be a direct-access Data RAM location (0x00-0x7F) or an
SFR (0x80-0xFF).
#data - 8-bit constant
#data 16 - 16-bit constant
bit - Direct-addressed bit in Data RAM or SFR.
addr 11 - 11-bit destination address used by ACALL and AJMP. The destination must be within the same 2K-
byte page of program memory as the first byte of the following instruction.
addr 16 - 16-bit destination address used by LCALL and LJMP. The destination may be anywhere within the
64K-byte program memory space.
There is one unused opcode (0xA5) that performs the same function as NOP.
All mnemonics copyrighted © Intel Corporation 1980.
Rev. 1.7 68
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
10.2. MEMORY ORGANIZATION
The memory organization of the CIP-51 System Controller is similar to that of a standard 8051. There are two
separate memory spaces: program memory and data memory. Program and data memory share the same address
space but are accessed via different instruction types. There are 256 bytes of internal data memory and 64K bytes of
internal program memory address space implemented within the CIP-51. The CIP-51 memory organization is
shown in Figure 10.2.
10.2.1. Program Memory
The CIP-51 has a 64K-byte program memory space. The MCU implements 32896 bytes of this program memory
space as in-system, reprogrammable Flash memory, organized in a contiguous block from addresses 0x0000 to
0x807F. Note: 512 bytes (0x7E00 – 0x7FFF) of this memory are reserved for factory use and are not available for
user program storage.
Program memory is normally assumed to be read-only. However, the CIP-51 can write to program memory by
setting the Program Store Write Enable bit (PSCTL.0) and using the MOVX instruction. This feature provides a
mechanism for the CIP-51 to update program code and use the program memory space for non-volatile data storage.
Refer to Section 11 (Flash Memory) for further details.
10.2.2. Data Memory
The CIP-51 implements 256 bytes of internal RAM mapped into the data memory space from 0x00 through 0xFF.
The lower 128 bytes of data memory are used for general purpose registers and scratch pad memory. Either direct
or indirect addressing may be used to access the lower 128 bytes of data memory. Locations 0x00 through 0x1F are
addressable as four banks of general purpose registers, each bank consisting of eight byte-wide registers. The next
16 bytes, locations 0x20 through 0x2F, may be addressed as bytes or as 128 bit locations accessible with the direct-
bit addressing mode.
The upper 128 bytes of data memory are accessible only by indirect addressing. This region occupies the same
address space as the Special Function Registers (SFR) but is physically separate from the SFR space. The
addressing mode used by an instruction when accessing locations above 0x7F determines whether the CPU accesses
the upper 128 bytes of data memory space or the SFRs. Instructions that use direct addressing will access the SFR
space. Instructions using indirect addressing above 0x7F will access the upper 128 bytes of data memory. Figure
10.2 illustrates the d ata memory organization of the CIP-51.
The C8051F005/06/07/15/16/17 also have 2048 bytes of RAM in the external data memory space of the CIP-51,
accessible using the MOVX instruction. Refer to Section 12 (External RAM) for details.
10.2.3. General Purpose Registers
The lower 32 bytes of data memory, locations 0x00 through 0x1F, may be addressed as four banks of general-
purpose registers. Each bank consists of eight byte-wide registers designated R0 through R7. Only one of these
banks may be enabled at a time. Two bits in the program status word, RS0 (PSW.3) and RS1 (PSW.4), select the
active register bank (see description of the PSW in Figure 10.6). This allows fast context switching when entering
subroutines and interrupt service routines. Indirect addressing modes use registers R0 and R1 as index registers.
10.2.4. Bit Addressable Locations
In addition to direct access to data memory organized as bytes, the sixteen data memory locations at 0x20 through
0x2F are also accessible as 128 individually addressable bits. Each bit has a bit address from 0x00 to 0x7F. Bit 0
of the byte at 0x20 has bit address 0x00 while bit 7 of the byte at 0x20 has bit address 0x07. Bit 7 of the byte at
0x2F has bit address 0x7F. A bit access is distinguished from a full byte access by the type of instruction used (bit
source or destination operands as opposed to a byte source or destination).
The MCS-51™ assembly language allows an alternate notation for bit addressing of the form XX.B where XX is the
byte address and B is the bit position within the b yte. Fo r example, the instruction:
MOV C, 22h.3
moves the Boolean value at 0x13 (bit 3 of the byte at location 0x22) into the user Carry flag.
69 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 10.2. Memory Map
10.2.5. Stack
A programmer’s stack can be located anywhere in the 256-byte data memory. The stack area is designated using
the Stack Pointer (SP, 0x81) SFR. The SP will point to the last location used. The next value pushed on the stack is
placed at SP+1 and then SP is incremented. A reset initializes the stack pointer to location 0x07. Therefore, the
first value pushed on the stack is placed at location 0x08, which is also the first register (R0) of register bank 1.
Thus, if more than one register bank is to be used, the SP should be initialized to a location in the data memory not
being used for data storage. The stack depth can extend up to 256 bytes.
The MCUs also have built-in hardware for a stack record. The stack record is a 32-bit shift register, where each
Push or increment SP pushes one record bit onto the register, and each Call or interrupt pushes two record bits onto
the register. (A Pop or decrement SP pops one record bit, and a Return pops two record bits, also.) The stack
record circuitry can also detect an overflow or underflow on the Stack, and can notify the debug software even with
the MCU running full-speed debug.
FLASH
(In-System
Programmable in 512
Byte Sectors)
PROGRAM MEMORY
0x0000
0x7FFF
(Direct and Indirect
Addressing)
0x00
0x7F
Upper 128 RAM
(Indirect Addressing
Only)
0x80
0xFF Special Function
Register's
(Direct Addressing Only)
RESERVED
0x7E00
0x7DFF
128 Byte ISP FLASH
0x8000
0x807F
DATA MEMORY
General Purpose
Registers
0x1F
0x20
0x2F Bit Addressable
Lower 128 RAM
(Direct and Indirect
Addressing)
0x30
INTERNAL DATA ADDRESS SPACE
EXTERNAL DATA ADDRESS SPACE
RAM - 2048 Bytes
(accessable using MOVX
command)
0x0000
0x07FF
(same 2048 byte RAM block )
0x0800
0x0FFF
(same 2048 byte RAM block )
0xF800
0xFFFF
The same 2048 byte RAM
block can be addressed on
2k boundaries throughout
the 64k External Data
Memory space.
(same 2048 byte RAM block )
0x1000
0x17FF
Rev. 1.7 70
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
10.3. SPECIAL FUNCTION REGISTERS
The direct-access data memory locations from 0x80 to 0xFF constitute the special function registers (SFRs). The
SFRs provide control and data exchange with the CIP-51’s resources and peripherals. The CIP-51 duplicates the
SFRs found in a typical 8051 implementation as well as implementing additional SFRs used to configure and access
the sub-systems unique to the MCU. This allows the addition of new functionality while retaining compatibility
with the MCS-51™ instruction set. Table 10.3 lists the SFRs implemented in the CIP-51 System Controller.
The SFR registers are accessed any time the direct addressing mode is used to access memory locations from 0x80
to 0xFF. SFRs with addresses ending in 0x0 or 0x8 (e.g. P0, TCON, P1, SCON, IE, etc.) are bit-addressable as well
as byte-addressable. All other SFRs are byte-addressable only. Unoccupied addresses in the SFR space are
reserved for future use. Accessing these areas will have an indeterminate effect and should be avoided. Refer to the
corresponding pages of the datasheet, as indicated in Table 10.3, for a detailed description of each register.
Table 10.2. Special Function Register Memory Map
F8 SPI0CN PCA0H PCA0CPH0 PCA0CPH1 PCA0CPH2 PCA0CPH3 PCA0CPH4 WDTCN
F0 B EIP1 EIP2
E8 ADC0CN PCA0L PCA0CPL0 PCA0CPL1 PCA0CPL2 PCA0CPL3 PCA0CPL4 RSTSRC
E0 ACC XBR0 XBR1 XBR2 EIE1 EIE2
D8 PCA0CN PCA0MD PCA0CPM0 PCA0CPM1 PCA0CPM2 PCA0CPM3 PCA0CPM4
D0 PSW REF0CN DAC0L DAC0H DAC0CN DAC1L DAC1H DAC1CN
C8 T2CON RCAP2L RCAP2H TL2 TH2 SMB0CR
C0 SMB0CN SMB0STA SMB0DAT SMB0ADR ADC0GTL ADC0GTH ADC0LTL ADC0LTH
B8 IP AMX0CF AMX0SL ADC0CF ADC0L ADC0H
B0 P3 OSCXCN OSCICN FLSCL FLACL***
A8 IE PRT1IF EMI0CN***
A0 P2 PRT0CF PRT1CF PRT2CF PRT3CF
98 SCON SBUF SPI0CFG SPI0DAT SPI0CKR CPT0CN CPT1CN
90 P1 TMR3CN TMR3RLL TMR3RLH TMR3L TMR3H
88 TCON TMOD TL0 TL1 TH0 TH1 CKCON PSCTL
80 P0 SP DPL DPH PCON
0(8) 1(9) 2(A) 3(B) 4(C) 5(D) 6(E) 7(F)
Bit Addressable
Table 10.3. Special Function Registers
SFRs are listed in alphabetical order. All undefined SFR locations are reserved.
* Refers to a register in the C8051F000/1/2/5/6/7 only.
** Refers to a register in the C8051F010/1/2/5/6/7 only.
*** Refers to a register in the C8051F005/06/07/15/16/17 only.
Address Register Description Page No.
0xE0 ACC Accumulator 76
0xBC ADC0CF ADC Configuration 33*, 42**
0xE8 ADC0CN ADC Control 34*, 45**
0xC5 ADC0GTH ADC Greater-Than Data Word (High Byte) 36*, 47**
0xC4 ADC0GTL ADC Greater-Than Data Word (Low Byte) 36*, 47**
0xBF ADC0H ADC Data Word (High Byte) 35*, 46**
0xBE ADC0L ADC Data Word (Low Byte) 35*, 46**
71 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Address Register Description Page No.
0xC7 ADC0LTH ADC Less-Than Data Word (High Byte) 36*, 47**
0xC6 ADC0LTL ADC Less-Than Data Word (Low Byte) 36*, 47**
0xBA AMX0CF ADC MUX Configuration 31*, 42**
0xBB AMX0SL ADC MUX Channel Selection 32*, 43**
0xF0 B B Register 76
0x8E CKCON Clock Control 144
0x9E CPT0CN Comparator 0 Control 56
0x9F CPT1CN Comparator 1 Control 58
0xD4 DAC0CN DAC 0 Control 52
0xD3 DAC0H DAC 0 Data Word (High Byte) 52
0xD2 DAC0L DAC 0 Data Word (Low Byte) 52
0xD7 DAC1CN DAC 1 Control 53
0xD6 DAC1H DAC 1 Data Word (High Byte) 53
0xD5 DAC1L DAC 1 Data Word (Low Byte) 53
0x83 DPH Data Pointer (High Byte) 74
0x82 DPL Data Pointer (Low Byte) 74
0xE6 EIE1 Extended Interrupt Enable 1 81
0xE7 EIE2 Extended Interrupt Enable 2 82
0xF6 EIP1 External Interrupt Priority 1 83
0xF7 EIP2 External Interrupt Priority 2 84
0xAF EMI0CN External Memory Interface Control 92***
0xB7 FLACL Flash Access Limit 90***
0xB6 FLSCL Flash Memory Timing Prescaler 91
0xA8 IE Interrupt Enable 79
0xB8 IP Interrupt Priority Control 80
0xB2 OSCICN Internal Oscillator Control 100
0xB1 OSCXCN External Oscillator Control 101
0x80 P0 Port 0 Latch 109
0x90 P1 Port 1 Latch 110
0xA0 P2 Port 2 Latch 111
0xB0 P3 Port 3 Latch 112
0xD8 PCA0CN Programmable Counter Array 0 Control 160
0xFA PCA0CPH0 PCA Capture Module 0 Data Word (High Byte) 163
0xFB PCA0CPH1 PCA Capture Module 1 Data Word (High Byte) 163
0xFC PCA0CPH2 PCA Capture Module 2 Data Word (High Byte) 163
0xFD PCA0CPH3 PCA Capture Module 3 Data Word (High Byte) 163
0xFE PCA0CPH4 PCA Capture Module 4 Data Word (High Byte) 163
0xEA PCA0CPL0 PCA Capture Module 0 Data Word (Low Byte) 163
0xEB PCA0CPL1 PCA Capture Module 1 Data Word (Low Byte) 163
0xEC PCA0CPL2 PCA Capture Module 2 Data Word (Low Byte) 163
0xED PCA0CPL3 PCA Capture Module 3 Data Word (Low Byte) 163
Rev. 1.7 72
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Address Register Description Page No.
0xEE PCA0CPL4 PCA Capture Module 4 Data Word (Low Byte) 163
0xDA PCA0CPM0 Programmable Counter Array 0 Capture/Compare 0 162
0xDB PCA0CPM1 Programmable Counter Array 0 Capture/Compare 1 162
0xDC PCA0CPM2 Programmable Counter Array 0 Capture/Compare 2 162
0xDD PCA0CPM3 Programmable Counter Array 0 Capture/Compare 3 162
0xDE PCA0CPM4 Programmable Counter Array 0 Capture/Compare 4 162
0xF9 PCA0H PCA Counter/Timer Data Word (High Byte) 163
0xE9 PCA0L PCA Counter/Timer Data Word (Low Byte) 163
0xD9 PCA0MD Programmable Counter Array 0 Mode 161
0x87 PCON Power Control 86
0xA4 PRT0CF Port 0 Configuration 109
0xA5 PRT1CF Port 1 Configuration 110
0xAD PRT1IF Port 1 Interrupt Flags 110
0xA6 PRT2CF Port 2 Configuration 111
0xA7 PRT3CF Port 3 Configuration 112
0x8F PSCTL Program Store RW Control 88
0xD0 PSW Program Status Word 75
0xCB RCAP2H Counter/Timer 2 Capture (High Byte) 151
0xCA RCAP2L Counter/Timer 2 Capture (Low Byte) 151
0xD1 REF0CN Voltage Reference Control Register 61
0xEF RSTSRC Reset Source Register 97
0x99 SBUF Serial Data Buffer (UART) 136
0x98 SCON Serial Port Control (UART) 137
0xC3 SMB0ADR SMBus 0 Address 120
0xC0 SMB0CN SMBus 0 Control 118
0xCF SMB0CR SMBus 0 Clock Rate 119
0xC2 SMB0DAT SMBus 0 Data 120
0xC1 SMB0STA SMBus 0 Status 121
0x81 SP Stack Pointer 74
0x9A SPI0CFG Serial Peripheral Interface Configuration 127
0x9D SPI0CKR SPI Clock Rate 129
0xF8 SPI0CN SPI Bus Control 128
0x9B SPI0DAT SPI Port 1Data 129
0xC8 T2CON Counter/Timer 2 Control 150
0x88 TCON Counter/Timer Control 142
0x8C TH0 Counter/Timer 0 Data Word (High Byte) 145
0x8D TH1 Counter/Timer 1 Data Word (High Byte) 145
0xCD TH2 Counter/Timer 2 Data Word (High Byte) 151
0x8A TL0 Counter/Timer 0 Data Word (Low Byte) 145
0x8B TL1 Counter/Timer 1 Data Word (Low Byte) 145
0xCC TL2 Counter/Timer 2 Data Word (Low Byte) 151
73 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Address Register Description Page No.
0x89 TMOD Counter/Timer Mode 143
0x91 TMR3CN Timer 3 Control 152
0x95 TMR3H Timer 3 High 153
0x94 TMR3L Timer 3 Low 153
0x93 TMR3RLH Timer 3 Reload High 153
0x92 TMR3RLL Timer 3 Reload Low 153
0xFF WDTCN Watchdog Timer Control 96
0xE1 XBR0 Port I/O Crossbar Configuration 1 105
0xE2 XBR1 Port I/O Crossbar Configuration 2 107
0xE3 XBR2 Port I/O Crossbar Configuration 3 108
0x84-86, 0x96-97, 0x9C,
0xA1-A3, 0xA9-AC,
0xAE, 0xB3-B5, 0xB9,
0xBD, 0xC9, 0xCE,
0xDF, 0xE4-E5, 0xF1-F5
Reserved
* Refers to a register in the C8051F000/1/2/5/6/7 only.
** Refers to a register in the C8051F010/1/2/5/6/7 only.
*** Refers to a register in the C8051F005/06/07/15/16/17 only.
Rev. 1.7 74
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
10.3.1. Register Descriptions
Following are descriptions of SFRs related to the operation of the CIP-51 System Controller. Reserved bits should
not be set to logic l. Future product versions may use these bits to implement new features in which case the reset
value of the b it will be lo gic 0 , selecting th e feature’s defau lt state. Detailed descrip tions o f the remaining SFRs are
included in the sections of the datasheet associated with their corresponding system function.
Figure 10.3. SP: Stack Pointer
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000111
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0x81
Figure 10.4. DPL: Data Pointer Low Byte
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0x82
Figure 10.5. DPH: Data Pointer High Byte
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0x83
Bits 7-0: SP: Stack Pointer.
The stack pointer holds the location of the top of the stack. The stack pointer is
incremented before every PUSH operation. The SP register defaults to 0x07 after reset.
Bits 7-0: DPL: Data Pointer Low.
The DPL register is the low byte of the 16-bit DPTR. DPTR is used to access indirectly
addressed RAM and Flash Memory.
Bits 7-0: DPH: Data Pointer High.
The DPH register is the high byte of the 16-bit DPTR. DPTR is used to access indirectly
addressed RAM and Flash Memory.
75 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 10.6. PSW: Program Status Word
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
CY AC F0 RS1 RS0 OV F1 PARITY 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
(bit addressable) 0xD0
Bit7: CY: Carry Flag .
This bit is set when the last arithmetic operation resu lts in a carry (addition) or a b orrow
(subtraction). It is cleared to 0 by all other arithmetic operations.
Bit6: AC: Au xiliary Carry Flag.
This bit is set when the last arithmetic operation results in a carry into (addition) or a
borrow from (subtraction) the high order nibble. It is cleared to 0 by all other arithmetic
operations.
Bit5: F0 : User Flag 0.
This is a bit-addressable, general purpose flag for use under software control.
Bits4-3: RS1-RS0: Register Bank Select.
These bits select which register bank is used during register accesses.
RS1 RS0 Register Bank Address
0 0 0 0x00-0x07
0 1 1 0x08-0x0F
1 0 2 0x10-0x17
1 1 3 0x18-0x1F
Note: Any instruction which changes the RS1-RS0 bits must not be immediately followed
by the “MOV Rn, A” instruction.
Bit2: OV: Overflow Flag.
This bit is set to 1 under the following circumstances:
An ADD, ADDC, or SUBB instruction causes a sign-change overflow.
A MUL instruction results in an overflow (result is greater than 255) .
A DIV instruction causes a divide-by-zero condition.
The OV bit is cleared to 0 by the ADD, ADDC, SUBB, MUL, and DIV instructions in all
other cases.
Bit1: F1 : User Flag 1.
This is a bit-addressable, general purpose flag for use under software control.
Bit0: PARITY: Parity Flag .
(Read only)
This bit is set to 1 if the sum of the eight bits in the accumulator is odd and cleared if the
sum is even.
Rev. 1.7 76
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 10.7. ACC: Accumulator
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
ACC.7 ACC.6 ACC.5 ACC.4 ACC.3 ACC.2 ACC.1 ACC.0 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
(bit addressable) 0xE0
Figure 10.8. B: B Register
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
B.7 B.6 B.5 B.4 B.3 B.2 B.1 B.0 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
(bit addressable) 0xF0
Bits 7-0: ACC: Accumulator
This register is the accumulator for arithmetic operations.
Bits 7-0: B: B Register
This register serves as a second accumulator for certain arithmetic operations.
77 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
10.4. INTERRUPT HANDLER
The CIP-51 includes an extended interrupt system supporting a total of 22 interrupt sources with two priority levels.
The allocation of interrupt sources between on-chip peripherals and external inputs pins varies according to the
specific version of the device. Each interrupt source has one or more associated interrupt-pending flag(s) located in
an SFR. When a peripheral or external source meets a valid interrupt condition, the associated interrupt-pending
flag is set to logic 1.
If interrupts are enabled for the source, an interrupt request is generated when the interrupt-pending flag is set. As
soon as execution of the current instruction is complete, the CPU generates an LCALL to a predetermined address
to begin execution of an interrupt service routine (ISR). Each ISR must end with an RETI instruction, which
returns program execution to the next instruction that would have been executed if the interrupt request had not
occurred. If interrupts are not enabled, the interrupt-pending flag is ignored by the hardware and program execution
continues as normal. (The interrupt-pending flag is set to logic 1 regardless of the interrupt’s enable/disable state.)
Each interrupt source can be individually enabled or disabled through the use of an associated interrupt enable bit in
an SFR (IE-EIE2). However, interrupts must first be globally enabled by setting the EA bit (IE.7) to logic 1 before
the individual interrupt enables are recognized. Setting the EA bit to logic 0 disables all interrupt sources regardless
of the individual interrupt-enable settings.
Some interrupt-pending flags are automatically cleared by the hardware when the CPU vectors to the ISR.
However, most are not cleared by the hardware and must be cleared by software before returning from the ISR. If
an interrupt-pending flag remains set after the CPU completes the return-from-interrupt (RETI) instruction, a new
interrupt request will be generated immediately and the CPU will re-enter the ISR after the completion of the next
instruction.
10.4.1. MCU Interrupt Sources and Vectors
The MCUs allocate 12 interrupt sources to on-chip peripherals. Up to 10 additional external interrupt sources are
available depending on the I/O pin configuration of the device. Software can simulate an interrupt by setting any
interrupt-pending flag to logic 1. If in terrupts are enab led fo r the flag , an interru pt req uest will be g enerated and the
CPU will vector to the ISR address associated with the interrupt-pending flag. MCU interrupt sources, associated
vector addresses, priority order and control bits are summarized in Table 10.4. Refer to the datasheet section
associated with a particular on-chip peripheral for information regarding valid interrupt conditions for the peripheral
and the behavior of its interrupt-pending flag(s).
10.4.2. External Interrupts
Two of the external interrup t sources (/INT0 an d /INT1) are co nfig urable as activ e-low level-sens itive or active-low
edge-sensitive inputs depending on the setting of IT0 (TCON.0) and IT1 (TCON.2). IE0 (TCON.1) and IE1
(TCON.3) serve as the interrupt-pending flag for the /INT0 and /INT1 external interrupts, resp ectively. If an /INT0
or /INT1 external interrupt is configured as edge-sensitive, the corresponding interrupt-pending flag is automatically
cleared by the hardware when the CPU vectors to the ISR. When configured as level sensitive, the interrupt-
pending flag follows the state of the external interrupt’s input pin. The external interrupt source must hold the input
active until the interrupt request is recognized. It must then deactivate the interrupt request before execution of the
ISR completes or another interrupt request will be generated.
The remaining four external interrupts (External Interrupts 4-7) are active-low, edge-sensitive inputs. The interrupt-
pending flags for these interrupts are in the Port 1 Interrupt Flag Register shown in Figure 15.10.
Rev. 1.7 78
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Table 10.4. Interrupt Summary
Interrupt Source Interrupt
Vector Priority
Order Interrupt-Pending Flag Enable
Reset 0x0000 Top None Always enabled
External Interrupt 0 (/INT0) 0x0003 0 IE0 (TCON.1) EX0 (IE.0)
Timer 0 Overflow 0x000B 1 TF0 (TCON.5) ET0 (IE.1)
External Interrupt 1 (/INT1) 0x0013 2 IE1 (TCON.3) EX1 (IE.2)
Timer 1 Overflow 0x001B 3 TF1 (TCON.7) ET1 (IE.3)
Serial Port (UART) 0x0023 4 RI (SCON.0)
TI (SCON.1) ES (IE.4)
Timer 2 Overflow (or EXF2) 0x002B 5 TF2 (T2CON.7) ET2 (IE.5)
Serial Peripheral Interface 0x0033 6 SPIF (SPI0CN.7)
WCOL (SPI0CN.6)
MODF (SPI0CN.5)
RXOVRN (SPI0CN.4)
ESPI0 (EIE1.0)
SMBus Interface 0x003B 7 SI (SMB0CN.3) ESMB0 (EIE1.1)
ADC0 Window Comparison 0x0043 8 ADWINT (ADC0CN.2) EWADC0 (EIE1.2)
Programmable Counter Array 0 0x004B 9 CF (PCA0CN.7)
CCFn (PCA0CN.n) EPCA0 (EIE1.3)
Comparator 0 Falling Edge 0x0053 10 CP0FIF (CPT0CN.4) ECP0F (EIE1.4)
Comparator 0 Rising Edge 0x005B 11 CP0RIF (CPT0CN.5) ECP0R (EIE1.5)
Comparator 1 Falling Edge 0x0063 12 CP1FIF (CPT1CN.4) ECP1F (EIE1.6)
Comparator 1 Rising Edge 0x006B 13 CP1RIF (CPT1CN.5) ECP1R (EIE1.7)
Timer 3 Overflow 0x0073 14 TF3 (TMR3CN.7) ET3 (EIE2.0)
ADC0 End of Conversion 0x007B 15 ADCINT (ADC0CN.5) EADC0 (EIE2.1)
External Interrupt 4 0x0083 16 IE4 (PRT1IF.4) EX4 (EIE2.2)
External Interrupt 5 0x008B 17 IE5 (PRT1IF.5) EX5 (EIE2.3)
External Interrupt 6 0x0093 18 IE6 (PRT1IF.6) EX6 (EIE2.4)
External Interrupt 7 0x009B 19 IE7 (PRT1IF.7) EX7 (EIE2.5)
Unused Interrupt Location 0x00A3 20 None Reserved (EIE2.6)
External Crystal OSC Ready 0x00AB 21 XTLVLD (OSCXCN.7) EXVLD (EIE2.7)
10.4.3. Interrupt Priorities
Each interrupt source can be individually programmed to one of two priority levels: low or high. A low priority
interrupt service routine can be preempted by a high priority interrupt. A high priority interrupt cannot be
preempted. Each in terrupt has an associated in terrupt priority bit in an SFR (IP-EIP2 ) used to config ure its priority
level. Low priority is the default. If two interrupts are recognized simultaneously, the interrupt with the higher
priority is serviced first. If both in terrupts have the same priority level, a fixed priority ord er is used to arbitrate.
10.4.4. Interrupt Latency
Interrupt response time depends on the state of the CPU when the interrupt occurs. Pending interrupts are sampled
and priority decoded each system clock cycle. Therefore, the fastest possible response time is 5 system clock
cycles: 1 clock cycle to detect the interrupt and 4 clock cycles to co mplete the LCALL to the ISR. If an interrupt is
pending when a RETI is executed, a single instruction is executed before an LCALL is made to service the pending
interrupt. Therefore, the maximum response time for an interrupt (when no other interrupt is currently being
serviced or the new interrupt is of greater priority) occurs when the CPU is performing an RETI instruction
followed by a DIV as the next instruction. In this case, the response time is 18 system clock cycles: 1 clock cycle
to detect the interrupt, 5 clock cycles to execute the RETI, 8 clock cycles to complete the DIV instruction and 4
clock cycles to execute the LCALL to the ISR. If the CPU is executing an ISR for an interrupt with equal or higher
priority, the new interrupt will not be serviced until the current ISR completes, including the RETI and following
instruction.
79 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
10.4.5. Interrupt Register Descriptions
The SFRs used to enable the interrupt sources and set their priority level are described below. Refer to the datasheet
section associated with a particular on-chip peripheral for information regarding valid interrupt conditions for the
peripheral and the behavior of its interrupt-pending flag(s).
Figure 10.9. IE: Interrupt Enable
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
EA IEGF0 ET2 ES ET1 EX1 ET0 EX0 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
(bit addressable) 0xA8
Bit7: EA: En able All Interrupts.
This bit globally enables/disables all interrupts. It overrides the individual interrupt mask
settings.
0: Disable all interrupt sources.
1: Enable each interrupt according to its individual mask setting.
Bit6: IEGF0: General Purpose Flag 0.
This is a general purpose flag for use under software control.
Bit5: ET2: Enable Timer 2 Interrupt.
This bit sets the masking of the Timer 2 interrupt.
0: Disable all Timer 2 interrupts.
1: Enable interrupt requests generated by the TF2 flag (T2CON.7)
Bit4: ES: Enable Serial Port (UART) Interrupt.
This bit sets the masking of the Serial Port (UART) interru pt.
0: Disable all UART interrupts.
1: Enable interrupt requests generated by the R1 flag (SCON.0) or T1 flag (SCON.1).
Bit3: ET1: Enable Timer 1 Interrupt.
This bit sets the masking of the Timer 1 interrupt.
0: Disable all Timer 1 interrupts.
1: Enable interrupt requests generated by the TF1 flag (TCON.7).
Bit2: EX1: En able External Interrupt 1.
This bit sets the masking of external interrupt 1.
0: Disable external interrupt 1.
1: Enable interrupt requests generated by the /INT1 pin.
Bit1: ET0: Enable Timer 0 Interrupt.
This bit sets the masking of the Timer 0 interrupt.
0: Disable all Timer 0 interrupts.
1: Enable interrupt requests generated by the TF0 flag (TCON.5).
Bit0: EX0: En able External Interrupt 0.
This bit sets the masking of external interrupt 0.
0: Disable external interrupt 0.
1: Enable interrupt requests generated by the /INT0 pin.
Rev. 1.7 80
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 10.10. IP: Interrupt Priority
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
- - PT2 PS PT1 PX1 PT0 PX0 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
(bit addressable) 0xB8
Bits7-6: UNUSED. Read = 11b, W r ite = don’t care.
Bit5: PT2 Timer 2 Interrup t Prio rity Control.
This bit sets the priority of the Timer 2 interrupts.
0: Timer 2 interrupts set to low priority level.
1: Timer 2 interrupts set to high prio rity level.
Bit4: PS: Serial Port (UART) Interrupt Priority Control.
This bit sets the priority of the Serial Port (UART) interrupts.
0: UART interrupts set to low priority level.
1: UART interrupts set to high priority level.
Bit3: PT1: Timer 1 Interrupt Priority Co ntrol.
This bit sets the priority of the Timer 1 interrupts.
0: Timer 1 interrupts set to low priority level.
1: Timer 1 interrupts set to high prio rity level.
Bit2: PX1: Ex ternal Interrupt 1 Priority Control.
This bit sets the priority of the External Interrupt 1 interrupts.
0: External Interrupt 1 set to lo w priority level.
1: External Interrupt 1 set to h ig h priority level.
Bit1: PT0: Timer 0 Interrupt Priority Co ntrol.
This bit sets the priority of the Timer 0 interrupts.
0: Timer 0 interrupt set to low priority level.
1: Timer 0 interrupt set to high prio rity level.
Bit0: PX0: Ex ternal Interrupt 0 Priority Control.
This bit sets the priority of the External Interrupt 0 interrupts.
0: External Interrupt 0 set to lo w priority level.
1: External Interrupt 0 set to h ig h priority level.
81 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 10.11. EIE1: Extended Interrupt Enable 1
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
ECP1R ECP1F ECP0R ECP0F EPCA0 EWADC0 ESMB0 ESPI0 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xE6
Bit7: ECP1R: Enable Comparator 1 (CP1) Rising Edge Interrupt.
This bit sets the masking of the CP1 interrupt.
0: Disable CP1 Rising Edge interrupt.
1: Enable interrupt requests generated by the CP1RIF flag (CPT1CN.5).
Bit6: ECP1F: Enable Comparator 1 (CP1) Falling Edge Interrupt.
This bit sets the masking of the CP1 interrupt.
0: Disable CP1 Falling Edge interrupt.
1: Enable interrupt requests generated by the CP1FIF flag (CPT1CN.4).
Bit5: ECP0R: Enable Comparator 0 (CP0) Rising Edge Interrupt.
This bit sets the masking of the CP0 interrupt.
0: Disable CP0 Rising Edge interrupt.
1: Enable interrupt requests generated by the CP0RIF flag (CPT0CN.5).
Bit4: ECP0F: Enable Comparator 0 (CP0) Falling Edge Interrupt.
This bit sets the masking of the CP0 interrupt.
0: Disable CP0 Falling Edge interrupt.
1: Enable interrupt requests generated by the CP0FIF flag (CPT0CN.4).
Bit3: EPCA0: Enable Programmable Counter Array (PCA0) Interrupt.
This bit sets the masking of the PCA0 interrupts.
0: Disable all PCA0 interrupts.
1: Enable interrupt requests generated by PCA0.
Bit2: EWADC0: Enable Window Comparison ADC0 Interrupt.
This bit sets the masking of ADC0 Window Comparison interrupt.
0: Disable ADC0 Window Comparison Interrupt.
1: Enable Interrupt requests generated by ADC0 Window Comparisons.
Bit1: ESMB0 : En able SMBus 0 Interrupt.
This bit sets the masking of the SMBus interrupt.
0: Disable all SMBus interrupts.
1: Enable interrupt requests generated by the SI flag (SMB0CN.3).
Bit0: ESPI0: Enable Serial Peripheral Interface 0 Interrupt.
This bit sets the masking of SPI0 interrup t.
0: Disable all SPI0 interrupts.
1: Enable Interrupt requests generated by SPI0.
Rev. 1.7 82
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 10.12. EIE2: Extended Interrupt Enable 2
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
EXVLD - EX7 EX6 EX5 EX4 EADC0 ET3 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xE7
Bit7: EXVLD: Enable External Clock Source Valid (XTLVLD) Interrupt.
This bit sets the masking of the XTLVLD interrup t.
0: Disable all XTLVLD interrupts.
1: Enable interrupt requests generated by the XTLVLD flag (OSCXCN.7)
Bit6: Reserv ed. Must Write 0. Reads 0.
Bit5: EX7: En able External Interrupt 7.
This bit sets the masking of External Interrupt 7.
0: Disable External Interrupt 7.
1: Enable interrupt requests generated by the External Interrupt 7 input pin.
Bit4: EX6: En able External Interrupt 6.
This bit sets the masking of External Interrupt 6.
0: Disable External Interrupt 6.
1: Enable interrupt requests generated by the External Interrupt 6 input pin.
Bit3: EX5: En able External Interrupt 5.
This bit sets the masking of External Interrupt 5.
0: Disable External Interrupt 5.
1: Enable interrupt requests generated by the External Interrupt 5 input pin.
Bit2: EX4: En able External Interrupt 4.
This bit sets the masking of External Interrupt 4.
0: Disable External Interrupt 4.
1: Enable interrupt requests generated by the External Interrupt 4 input pin.
Bit1: EADC0: Enable ADC0 End of Conversion Interrupt.
This bit sets the masking of the ADC0 End of Conversion Interrupt.
0: Disable ADC0 Conversion Interrupt.
1: Enable interrupt requests generated by the ADC0 Conversion Interrupt.
Bit0: ET3: Enable Timer 3 Interrupt.
This bit sets the masking of the Timer 3 interrupt.
0: Disable all Timer 3 interrupts.
1: Enable interrupt requests generated by the TF3 flag (TMR3CN.7)
83 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 10.13. EIP1: Extended Interrupt Priority 1
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
PCP1R PCP1F PCP0R PCP0F PPCA0 PWADC0 PSMB0 PSPI0 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xF6
Bit7: PCP1R: Comparator 1 (CP1) Rising Interrupt Priority Co ntrol.
This bit sets the priority of the CP1 interrupt.
0: CP1 rising interrupt set to low priority level.
1: CP1 rising interrupt set to high priority level.
Bit6: PCP1F: Comparator 1 (CP1) Falling Interrupt Priority Co ntrol.
This bit sets the priority of the CP1 interrupt.
0: CP1 falling interrupt set to low priority level.
1: CP1 falling interrup t set to high priority level.
Bit5: PCP0R: Comparator 0 (CP0) Rising Interrupt Priority Co ntrol.
This bit sets the priority of the CP0 interrupt.
0: CP0 rising interrupt set to low priority level.
1: CP0 rising interrupt set to high priority level.
Bit4: PCP0F: Comparator 0 (CP0) Falling Interrupt Priority Co ntrol.
This bit sets the priority of the CP0 interrupt.
0: CP0 falling interrupt set to low priority level.
1: CP0 falling interrup t set to high priority level.
Bit3: PPCA0: Programmable Counter Array (PCA0) Interrupt Priority Control.
This bit sets the priority of the PCA0 interrupt.
0: PCA0 interrupt set to low pr iority level.
1: PCA0 interrupt set to high priority level.
Bit2: PWADC0: ADC0 Window Comparator Interrupt Priority Control.
This bit sets the priority of the ADC0 Window interrupt.
0: ADC0 Window interrupt set to low priority level.
1: ADC0 Window interrupt set to high priority level.
Bit1: PSMB0 : SMBus 0 Interrupt Priority Control.
This bit sets the priority o f the SMBus interrupt.
0: SMBus interrupt set to low p riority level.
1: SMBus interrupt set to hig h priority level.
Bit0: PSPI0: Serial Peripheral Interface 0 Interrupt Priority Control.
This bit sets the priority of the SPI0 interrupt.
0: SPI0 interrupt set to low priority level.
1: SPI0 interrupt set to high priority level.
Rev. 1.7 84
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 10.14. EIP2: Extended Interrupt Priority 2
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
PXVLD - PX7 PX6 PX5 PX4 PADC0 PT3 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xF7
Bit7: PXVLD: External Clock Source Valid (XTLVLD) Interrupt Prio rity Control.
This bit sets the priority of the XTLVLD interrupt.
0: XTLVLD interrupt set to low priority level.
1: XTLVLD interrupt set to high priority level.
Bit6: Reserv ed: Must write 0. Reads 0.
Bit5: PX7: Ex ternal Interrupt 7 Priority Control.
This bit sets the priority of the External Interrupt 7.
0: External Interrupt 7 set to lo w priority level.
1: External Interrupt 7 set to h ig h priority level.
Bit4: PX6: Ex ternal Interrupt 6 Priority Control.
This bit sets the priority of the External Interrupt 6.
0: External Interrupt 6 set to lo w priority level.
1: External Interrupt 6 set to h ig h priority level.
Bit3: PX5: Ex ternal Interrupt 5 Priority Control.
This bit sets the priority of the External Interrupt 5.
0: External Interrupt 5 set to lo w priority level.
1: External Interrupt 5 set to h ig h priority level.
Bit2: PX4: Ex ternal Interrupt 4 Priority Control.
This bit sets the priority of the External Interrupt 4.
0: External Interrupt 4 set to lo w priority level.
1: External Interrupt 4 set to h ig h priority level.
Bit1: PADC0: ADC End of Conversion Interrupt Priority Control.
This bit sets the priority of the ADC0 End of Conversion Interrupt.
0: ADC0 End of Conversion interrupt set to low priority level.
1: ADC0 End of Conversion interrupt set to high priority level.
Bit0: PT3: Timer 3 Interrupt Priority Co ntrol.
This bit sets the priority of the Timer 3 interrupts.
0: Timer 3 interrupt set to low priority level.
1: Timer 3 interrupt set to high prio rity level.
85 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
10.5. Power Management Modes
The CIP-51 core has two software programmable power management modes: Idle and Stop. Idle mode halts the
CPU while leaving the external peripherals and internal clocks active. In Stop mode, the CPU is halted, all
interrupts and timers (except the Missing Clock Detector) are inactive, and the system clock is stopped. Since
clocks are running in Idle mode, power consumption is dependent upon the system clock frequency and the number
of peripherals left in active mode before entering Idle. Stop mode consumes the least power. Figure 10.15
describes the Power Control Register (PCON) used to control the CIP-51’s power management modes.
Although the CIP-51 has Idle and Stop modes built in (as with any standard 8051 architecture), power management
of the entire MCU is better accomplished by enabling/disabling individual peripherals as needed. Each analog
peripheral can be disabled when not in use and put into low power mode. Digital peripherals, such as timers or
serial buses, draw little power wh enever they are not in use. Turning o ff the oscillator saves even more power, but
requires a reset to restart the MCU.
10.5.1. Idle Mode
Setting the Idle Mode Select bit (PCON.0) causes the CIP-51 to halt the CPU and enter Idle mode as soon as the
instruction that sets the bit completes. All internal registers and memory maintain their original data. All analog
and digital peripherals can remain active during Idle mode.
Idle mode is terminated when an enabled interrupt or /RST is asserted. The assertion of an enabled interrupt will
cause the Idle Mode Selection bit (PCON.0) to be cleared and the CPU will resume operation. The pending
interrupt will be serviced and the next instruction to be executed after the return from interrupt (RETI) will be the
instruction immediately following the on e that set the Idle Mode Select bit. If Idle mode is terminated by an internal
or external reset, the CIP-51 performs a normal reset sequence and begins program execution at address 0x0000.
Note: If the instruction followin g the write o f the IDLE bit is a single-byte instru ction and an interrupt o ccurs during
the execution phase of the instruction that sets the IDLE b it, the CPU may not wake from Idle mode when a future
interrupt occurs. Any instructions that set the IDLE bit should be followed by an instruction that has 2 or more op-
code bytes, for example:
// in ‘C’:
PCON |= 0x01; // set IDLE bit
PCON = PCON; // ... followed by a 3-cycle dummy instruction
; in assembly:
ORL PCON, #01h ; set IDLE bit
MOV PCON, PCON ; ... followed by a 3-cycle dummy instruction
If enabled, the WDT will eventually cause an internal watchdog reset and thereby terminate the Idle mode. This
feature protects the system from an unintended permanent shutdown in the event of an inadvertent write to the
PCON register. If this behavior is not desired, the WDT may be disabled by software prior to entering the Idle
mode if the WDT was initially configured to allow this operation. This provides the opportunity for additional
power saving s, allowin g the system to remain in the Idle mode ind efinitely, waitin g fo r an ex ternal stimulus to wak e
up the system. Refer to Section 13.8 Watchdog Timer for more information on the use and configuration of the
WDT.
10.5.2. Stop Mode
Setting the Stop Mode Select bit (PCON.1) causes the CIP-51 to enter Stop mode as soon as the instruction that sets
the bit completes. In Stop mode, the CPU and oscillators are stopped, effectively shutting down all digital
peripherals. Each analog peripheral must be shut down individually prior to entering Stop Mode. Stop mode can
only be terminated by an internal or external reset. On reset, the CIP-51 performs the normal reset sequence and
begins program execution at address 0x0000.
Rev. 1.7 86
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
If enabled, the Missing Clock Detector will cause an internal reset and thereby terminate the Stop mode. The
Missing Clock Detector should be disabled if the CPU is to be put to sleep for longer than the MCD timeout of
100sec.
Figure 10.15. PCON: Power Control Register
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
SMOD GF4 GF3 GF2 GF1 GF0 STOP IDLE 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0x87
Bit7: SMOD: Serial Port Baud Rate Doubler Enable.
0: Serial Port baud rate is that defined by Serial Port Mode in SCON.
1: Serial Port baud rate is double that defined by Serial Port Mode in SCON.
Bits6-2: GF4-GF0: General Purpose Flags 4-0.
These are general purpose flags for use under software control.
Bit1: STOP: Sto p Mode Select.
Setting this bit will place the CIP-51 in Stop mode. This bit will always be read as 0.
1: Goes into power down mode. (Turns off internal oscillator).
Bit0: IDLE: Id le Mode Select.
Setting this bit will place the CIP-51 in Idle mode. This bit will always be read as 0.
1: Goes into idle mode. (Shuts off clock to CPU, but clock to Timers, Interrupts, Serial
Ports, and Analog Periph erals are still active.)
87 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
11. FLASH MEMORY
These devices include 32k + 128 bytes of on-chip, reprogrammable Flash memory for program code and non-
volatile data storage. The Flash memory can be programmed in-system, a single byte at a time, through the JTAG
interface or by software using the MOVX instruction. Once cleared to 0, a Flash bit must be erased to set it back to
1. The bytes would typically be erased (set to 0xFF) before being reprogrammed. The write and erase operations
are automatically timed by hardware for proper execution. Data polling to determine the end of the write/erase
operation is not required. The Flash memory is designed to withstand at least 20,000 write/erase cycles. Refer to
Table 11.1 for the electrical characteristics of the Flash memory.
11.1. Programming The Flash Memory
The simplest means of programming the Flash memory is through the JTAG interface using programming tools
provided by Silicon Labs or a third party vendor. This is the only means for programming a non-initialized device.
For details on the JTAG commands to program Flash memory, see Section 21.2.
The Flash memory can be programmed by software using the MOVX instruction with the address and data byte to
be programmed provided as normal operands. Before writing to Flash memory using MOVX, Flash write
operations must be enabled by setting the PSWE Program Store Write Enable bit (PSCTL.0) to logic 1. Writing to
Flash remains enabled until the PSW E bit is cleared by software.
Writes to Flash memory can clear bits but cannot set them. Only an erase operation can set bits in Flash. Therefore,
the byte location to be programmed must be erased before a new value can be written. The 32kbyte Flash memory
is organized in 512-byte sectors. The erase operation applies to an entire sector (setting all bytes in the sector to
0xFF). Setting the PSEE Program Store Erase Enable bit (PSCTL.1) and PSWE (PSCTL.0) bit to logic 1 and then
using the MOVX command to write a data byte to any byte location within the sector will erase an entire 512-byte
sector. The data byte written can be of any value because it is not actually written to the Flash. Flash erasure
remains enabled until the PSEE bit is cleared by software. The following sequence illustrates the algorithm for
programming the Flash memory by software:
1. Enable Flash Memory write/erase in FLSCL Register using FLASCL bits.
2. Set PSEE (PSCTL.1) to enable Flash sector erase.
3. Set PSWE (PSCTL.0) to enable Flash writes.
4. Use MOVX to write a data byte to any location within the 512-byte sector to be erased.
5. Clear PSEE to disable Flash sector erase.
6. Use MOVX to write a data byte to the desired byte location within the erased 512-byte sector. Repeat until
finished. (Any number of bytes can be written from a single byte to and entire sector.)
7. Clear the PSWE bit to disable Flash writes.
Write/Erase timing is automatically controlled by hardware based on the prescaler value held in the Flash Memory
Timing Prescaler register (FLSCL). The 4-bit prescaler value FLASCL determines the time interval for write/erase
operations. The FLASCL value required for a given system clock is shown in Figure 11.4, along with the formula
used to derive the FLASCL values. When FLASCL is set to 1111b, the write/erase operations are disabled. Note
that code execution in the 8051 is stalled while the Flash is being programmed or erased.
Table 11.1. FLASH Memory Electrical Characteristics
VDD = 2.7 to 3.6V, -40C to +85C unless otherwise specified.
PARAMETER CONDITIONS MIN TYP MAX UNITS
Endurance 20k 100k Erase/Wr
Erase Cycle Time 10 ms
Write Cycle Time 40 s
Rev. 1.7 88
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
11.2. Non-volatile Data Storage
The Flash memory can be used for non-volatile data storage as well as program code. This allows data such as
calibration coefficients to be calculated and stored at run time. Data is written using the MOVX instruction and
read using the MOVC instruction.
The MCU incorporates an additional 128-byte sector of Flash memory located at 0x8000 – 0x807F. This sector can
be used for program code or data storage. However, its smaller sector size makes it particularly well suited as
general purpose, non-volatile scratchpad memory. Even though Flash memory can be written a single byte at a
time, an entire sector must be erased first. In order to ch ange a single byte of a multi-byte data set, the data must be
moved to temporary storage. Next, the sector is erased, the data set updated and the data set returned to the original
sector. The 128-byte sector-size facilitates updating data without wasting program memory space by allowing the
use of internal data RAM for temporary storage. (A normal 512-byte sector is too large to be stored in the 256-byte
internal data memory.)
11.3. Security Options
The CIP-51 provides security options to protect the Flash memory from inadvertent modification by software as
well as prevent the viewing of proprietary program code and constants. The Program Store Write Enable
(PSCTL.0) and the Program Store Erase Enable (PSCTL.1) bits protect the Flash memory from accidental
modification by software. These bits must be explicitly set to logic 1 before software can modify the Flash memory.
Additional security features prevent proprietary program code and data constants from being read or altered across
the JTAG interface or by software running on the system controller.
A set of security lock bytes stored at 0x7DFE and 0x7DFF protect the Flash program memory from being read or
altered across the JTAG interface. Each bit in a security lock-byte protects one 4kbyte block of memory. Clearing
a bit to logic 0 in a Read lock byte prevents the corresponding block of Flash memory from being read across the
JTAG interface. Clearing a bit in the Write/Erase lock byte protects the block from JTAG erasures and/or writes.
The Read lock byte is at location 0x7DFF. The Write/Erase lock byte is located at 0x7DFE. Figure 11.2 shows the
location and bit definitions of the security bytes. The 512-byte sector containing the lock bytes can be written to,
but not erased by software. Writing to the reserved area should not be performed.
Figure 11.1. PSCTL: Program Store RW Control
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
- - - - - - PSEE PSWE 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0x8F
Bits7-2: UNUSED. Read = 000000b, W rite = don’t care.
Bit1: PSEE: Program Store Erase Enable.
Setting this bit allows an entire page of the Flash program memory to be erased provided
the PSWE bit is also set. After setting this bit, a write to Flash memory using the MOVX
instruction will erase the entire page that contains the location addressed by the MOVX
instruction. The value of the data byte written does not matter.
0: Flash program memory erasure disabled.
1: Flash program memory erasure enabled.
Bit0: PSWE: Program Store Write Enable.
Setting this bit allows writing a byte of data to the Flash program memory using the
MOVX instruction. The location must be erased before writing data.
0: Write to Flash program memory disabled.
1: Write to Flash program memory enabled.
89 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 11.2. Flash Program Memory Security Bytes
0x7E00
0x807F
0x8000
0x7DF
E
Program Memory
Space
0x0000
0x7DFF
Read Lock Byte
W rite/Erase Lock Byte
Software Read Limit
Reserved
Bit Memory Block
7
6
5
4
0x6000 - 0x6FFF
0x7000 - 0x7DFD
0x5000 - 0x5FFF
0x4000 - 0x4FFF
3
2
1
0
0x2000 - 0x2FFF
0x3000 - 0x3FFF
0x1000 - 0x1FFF
0x0000 - 0x0FFF
0x7FFF
Read and W rite/Erase Security Bits.
(Bit 7 is MSB.)
(This Block locked only if all
other blocks are locked)
0x7DFD
The lock bits can always be read and cleared to logic 0 regardless of the security setting applied to the block
containing the security bytes. This allows additional blocks to be protected after the block containing the security
bytes has been locked. However, the only means of removing a lock once set is to erase the entire program memory
space by performing a JTAG erase operation (i.e. cannot be done in user firmware). NOTE: Addressing either
security byte while performing a JTAG erase operation will automatically initiate erasure of the entire
program memory space (except for the reserved area). This erasure can only be performed via JTAG. If a
non-security byte in the 0x7C00-0x7DFF page is addressed during erasure, only that page (including the
security bytes) will be erased.
The Flash Access Limit security feature (see Figure 11.3) protects proprietary program code and data from being
read by software running on the C8051F005/06/07/15/16/17 MCUs. This feature provides support for OEMs that
wish to program the MCU with proprietary value-added firmware before distribution. The value-added firmware
can be protected while allowing additional code to be programmed in remaining program memory space later.
The Software Read Limit (SRL) is a 16-bit address that establishes two logical partitions in the program memory
space. The first is an upper partition consisting of all the program memory locations at or above the SRL address,
and the second is a lower partition consisting of all the program memory locations starting at 0x0000 up to (but
excluding) the SRL address. Software in the upper partition can execute code in the lower partition, but is
FLASH Read Lock Byte
Bits7-0: Each bit locks a corresponding block of memory. (Bit 7 is MSB.)
0: Read operations are locked (disabled) for corresponding block across the JTAG interface.
1: Read operations are unlocked (enabled) for corresponding block across the JTAG interface.
FLASH Write/Erase Lock Byte
Bits7-0: Each bit locks a corresponding block of memory.
0: Write/Erase operations are locked (disabled) for corresponding block across the JTAG interface.
1: Write/Erase operations are unlocked (enabled) for corresponding block across the JTAG interface.
FLASH Access Limit Register (FLACL)
The content of this register is used as the high byte of the 16-bit software read limit address. The 16-
bit read limit address value is calculated as 0xNN00 where NN is replaced by the contents of this
register. Software running at or above this address is prohibited from using the MOVX or MOVC
instructions to read, write, or erase, locations below this add ress. Any attempts to read locations
below this limit will return the value 0x00.
Rev. 1.7 90
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
prohibited from reading locations in the lower partition using the MOVC instruction. (Executing a MOVC
instruction from the upper partition with a source address in the lower partition will always return a data value of
0x00.) Software running in the lower partition can access locations in both the upper and lower partition without
restriction.
The Value-added firmware should be placed in the lower partition. On reset, control is passed to the value-added
firmware via the reset vector. Once the value-added firmware completes its initial execution, it branches to a
predetermined location in the upper partition. If entry points are published, software running in the upper partition
may execute program code in the lower partition, but it cannot read the contents of the lower partition. Parameters
may be passed to the program code running in the lower partition either through the typical method of placing them
on the stack or in registers before the call or by placing them in prescribed memory locations in the upper partition.
The SRL address is specified using the contents of the Flash Access Register. The 16-bit SRL address is calculated
as 0xNN00, where NN is the contents of the SRL Security Register. Thus, the SRL can be located on 256-byte
boundaries anywhere in program memory space. However, the 512-byte erase sector size essentially requires that a
512 boundary be used. The contents of a non-initialized SRL security byte is 0x00, thereby setting the SRL address
to 0x0000 and allowing read access to all locations in program memory space by default.
Figure 11.3. FLACL: Flash Access Limit (C8051F005/06/07/15/16/17 only)
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xB7
Bits 7-0: FLACL: Flash Access Limit.
This register holds the high byte of the 16-bit program memory read/write/erase limit
address. The entire 16-
b
it access limit address value is calculated as 0xNN00 where NN is
replaced by contents of FLACL. A write to this register sets the Flash Access Limit. This
register can only be written once after any reset. Any subsequent writes are ignored
until the next reset.
91 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 11.4. FLSCL: Flash Memory Timing Prescaler
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
FOSE FRAE - - FLASCL 10001111
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xB6
Bit7: FOSE: Flash One-Shot Timer Enable
0: Flash One-shot timer disabled.
1: Flash One-shot timer enabled
Bit6: FRAE: Flash Read Always Enable
0: Flash reads per one-shot timer
1: Flash always in read mode
Bits5-4: UNUSED. Read = 00b, W r ite = don’t care.
Bits3-0: FLASCL: Flash Memory Timing Prescaler.
This register specifies the prescaler value for a given system clock required to generate the
correct timing for Flash write/erase operations. If the prescaler is set to 1111b, Flash
write/erase operations are disabled.
0000: System Clock < 50kHz
0001: 50kHz System Clock < 100kHz
0010: 100kHz System Clock < 200kHz
0011: 200kHz System Clock < 400kHz
0100: 400kHz System Clock < 800kHz
0101: 800kHz System Clock < 1.6MHz
0110: 1.6MHz System Clock < 3.2MHz
0111: 3.2MHz System Clock < 6.4MHz
1000: 6.4MHz System Clock < 12.8MHz
1001: 12.8MHz System Clock < 25.6MHz
1010: 25.6MHz System Clock < 51.2MHz *
1011, 1100, 1101, 1110: Reserved Values
1111: Flash Memory Write/Erase Disabled
The prescaler value is the smallest value satisfying the following equation:
FLASCL > log2(System Clock / 50kHz)
* For test purposes. The C8051F000 family is not guaranteed for operation over 25MHz.
Rev. 1.7 92
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
12. EXTERNAL RAM (C8051F005/06/07/15/16/17)
The C8051F005/06/07/15/16/17 MCUs include 2048 bytes of RAM mapped into the external data memory space.
All of these address locations may be accessed using the external move instruction (MOVX) and the data pointer
(DPTR), or using MOVX indirect addressing mode. If the MOVX instruction is used with an 8-bit address operand
(such as @R1), then the high byte of the 16-bit address is provided by the External Memory Interface Control
Register (EMI0CN as shown in Figure 12.1). Note: the MOVX instruction is also used for writes to the Flash
memory. See Section 11 for details. The MOVX instruction accesses XRAM by default (i.e. PSTCL.0 = 0).
For any of the addressing modes the upper 5-bits of the 16-bit external data memory address word are “don’t cares”.
As a result, the 2048-byte RAM is mapped modulo style over the entire 64k external data memory address range.
For example, the XRAM byte at address 0x0000 is also at address 0x0800, 0x1000, 0x1800, 0x2000, etc. This is a
useful feature when doing a linear memory fill, as the address pointer doesn’t have to be reset when reaching the
RAM block boundary.
Figure 12.1. EMI0CN: External Memory Interface Control
R R R R R R/W R/W R/W Reset Value
- - - - - PGSEL2 PGSEL1 PGSEL0 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xAF
Bits 7-3: Not Used – reads 00000b
Bits 2-0: PGSEL[2:0]: XRAM Page Select Bits
The XRAM Page Select Bits provide the high byte of the 16-bit external data memory
address when using an 8-bit MOVX command, effectively selecting a 256-byte page of
RAM. The upper 5-bits are “don’t cares”, so the 2k address blocks are repeated modulo
over the entire 64k external data memory address space.
000: xxxxx000b
001: xxxxx001b
010: xxxxx010b
011: xxxxx011b
100: xxxxx100b
101: xxxxx101b
110: xxxxx110b
111: xxxxx111b
93 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
13. RESET SOURCES
The reset circuitry of the MCUs allows the controller to be easily placed in a predefined default condition. On entry
to this reset state, the CIP-51 halts program execution, forces the external port pins to a known state and initializes
the SFRs to their defined reset values. Interrupts and timers are disabled. On exit, the program counter (PC) is
reset, and program execution starts at location 0x0000.
All of the SFRs are reset to predefined values. The reset values of the SFR bits are defined in the SFR detailed
descriptions. The contents of internal data memory are not changed during a reset and any previously stored data is
preserved. However, since the stack pointer SFR is reset, the stack is effectively lost even though the data on the
stack are not altered.
The I/O por t latches are reset to 0x FF (all logic ones), activating internal weak pull-ups which take the ex ternal I/O
pins to a high state. The weak pull-ups are enabled during and after the reset. If the source of reset is from the VDD
Monitor or writing a 1 to PORSF, the /RST pin is driven low until the end of the VDD reset timeout.
On exit from the reset state, the MCU uses the internal oscillator running at 2MHz as the system clock by default.
Refer to Section 14 for information on selecting and configuring the system clock source. The Watchdog Timer is
enabled using its longest timeout interval. (Section 13.8 details the use of the Watchdog Timer.)
There are seven sources for putting the MCU into the reset state: power-on/power-fail, external /RST pin, external
CNVSTR signal, software commanded, Comparator 0, Missing Clock Detector, and Watchdog Timer. Each reset
source is described below:
Figure 13.1. Reset Sources Diagram
WDT
CIP-51
Core
Missing
Clock
Detector
(one-
shot)
WDT
Strobe
(Software Reset)
/RST
+
-
VDD
Supply
Reset
Timeout
(wired-OR)
System Reset
Supply
Monitor
PRE
Reset
Funnel
+
-
CP0+
Comparator 0
CP0-
(Port
I/O)
Crossbar CNVSTR
CNVRSEF
C0RSEF
EN
WDT
Enable
EN
MCD
Enable
SWRSF
System
Clock
Rev. 1.7 94
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
13.1. Power-on Reset
The C8051F000 family incorporates a power supply monitor that holds the MCU in the reset state until VDD rises
above the VRST level during power-up. (See Figure 13.2 for timing diagram, and refer to Table 13.1 for the
Electrical Characteristics of the power supply monitor circuit.) The /RST pin is asserted (low) until the end of the
100ms VDD Monitor timeout in order to allow the VDD supply to become stable.
On exit from a power-on reset, the PORSF flag (RSTSRC.1) is set by hardware to logic 1. All of the other reset
flags in the RSTSRC Register are indeterminate. PORSF is cleared by a reset from any other source. Since all
resets cause program execution to begin at the same location (0x0000), software can read the PORSF flag to
determine if a power-up was the cause of reset. The content of internal data memory should be assumed to be
undefined after a power-on reset.
13.2. Software Forced Reset
Writing a 1 to the PORSF bit forces a Power-On Reset as described in Section 13.1.
Figure 13.2. VDD Monitor Timing Diagram
13.3. Power-fail Reset
When a power-down transition or power irregularity causes VDD to drop below VRST, the power supply monitor
will drive the /RST pin low and return the CIP-51 to the reset state (see Figure 13.2). When VDD returns to a level
above VRST, the CIP-51 will leave the reset state in the same manner as that for the power-on reset. Note that even
though internal data memory contents are not altered by the power-fail reset, it is impossible to determine if VDD
dropped below the level required for data retention. If the PORSF flag is set, the data may no longer be valid.
/RST
t
volts
1.0
2.0
Logic HIGH
Logic LOW
100ms 100ms
VDD
2.70
2.40
V
RST
95 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
13.4. External Reset
The external /RST pin provides a means for external circuitry to force the MCU into a reset state. Asserting an
active-low signal on the /RST pin will cause the MCU to enter the reset state. Although there is a weak internal
pullup, it may be desirable to provide an external pull-up and/or decoupling of the /RST pin to avoid erroneous
noise-induced resets. Th e MCU will remain in reset until at least 12 clock cycles after the activ e-low /RST sign al is
removed. The PINRSF flag (RSTSRC.0) is set on exit from an external reset. The /RST pin is also 5V tolerant.
13.5. Missing Clock Detector Reset
The Missing Clock Detector is essentially a one-shot circuit that is triggered by the MCU system clock. If the
system clock goes away for more than 100s, the one-shot will time out and generate a reset. After a Missing Clock
Detector reset, the MCDRSF flag (RSTSRC.2) will be set, signifying the MSD as the reset source; otherwise, this
bit reads 0. The state of the /RST pin is unaffected by this reset. Setting the MSCLKE bit in the OSCICN register
(see Figure 14.2) enables the Missing Clock Detector.
13.6. Comparator 0 Reset
Comparator 0 can be configured as an active-low reset input by writing a 1 to the C0RSEF flag (RSTSRC.5).
Comparator 0 should be enabled using CPT0CN.7 (see Figure 8.3) at least 20s prior to writing to C0RSEF to
prevent any turn-on chatter on the output from generating an unwanted reset. When configured as a reset, if the
non-inverting input voltage (on CP0+) is less than the inverting input voltage (on CP0-), the MCU is put into the
reset state. After a Comparator 0 Reset, the C0RSEF flag (RSTSRC.5) will read 1 signifying Comparator 0 as the
reset source; otherwise, this bit reads 0. The state of the /RST pin is unaffected by this reset. Also, Comparator 0
can generate a reset with or without the system clock.
13.7. External CNVSTR Pin Reset
The external CNVSTR signal can be configured as an active-low reset input by writing a 1 to the CNVRSEF flag
(RSTSRC.6). The CNVSTR signal can appear on any of the P0, P1, or P2 I/O pins as described in Section 15.1.
(Note that the Crossbar must be configured for the CNVSTR signal to be routed to the appropriate Port I/O.) The
Crossbar should be configured and enabled before the CNVRSEF is set to configure CNVSTR as a reset source.
When con fig ur ed as a reset, CNVSTR is active-lo w and lev el sensitiv e. After a CNVSTR reset, the CNVRSEF flag
(RSTSRC.6) will read 1 signifying CNVSTR as the reset source; otherwise, th is bit reads 0. The state of the /RST
pin is unaffected by this reset.
13.8. Watchdog Timer Reset
The MCU includes a programmable Watchdog Timer (WDT) running off the system clock. The WDT will force
the MCU into the reset state when the watchdog timer overflows. To prevent the reset, the WDT must be restarted
by application software before the overflow occurs. If the system experiences a software/hardware malfunction
preventing the software from restarting the WDT, the WDT will overflow and cause a reset. This should prevent
the system from running out of control.
The WDT is automatically enabled and started with the default maximum time interval on exit from all resets. If
desired the WDT can be disabled by system software or locked on to prevent accidental disabling. Once locked, the
WDT cannot be disabled until the next system reset. The state of the /RST pin is unaffected by this reset.
Rev. 1.7 96
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
13.8.1. Watchdog Usage
The WDT consists of a 21-bit timer running from the programmed system clock. The timer measures the period
between specific writes to its control register. If this period exceeds the programmed limit, a WDT reset is
generated. The WDT can be enabled and disabled as needed in software, or can be permanently enabled if desired.
Watchdog features are controlled via the Watchdog Timer Control Register (WDTCN) shown in Figure 13.3.
Enable/Reset WDT
The watchdog timer is both enabled and the countdown restarted by writing 0xA5 to the WDTCN register. The
user’s application software should include periodic writes of 0xA5 to WDTCN as needed to prevent a watchdog
timer overflow. The WDT is enabled and restarted as a result of any system reset.
Disable WDT
Writing 0xDE followed by 0xAD to the WDTCN register disables the WDT. The following code segment
illustrates disabling the WDT.
CLR EA ; disable all interrupts
MOV WDTCN,#0DEh ; disable software
MOV WDTCN,#0ADh ; watchdog timer
SETB EA ; re-enable interrupts
The writes of 0xDE and 0xAD must occur within 4 clock cycles of each other, or the disable operation is ignored.
Interrupts should be disabled during this procedure to avoid delay between the two writes.
Disable WDT Lockout
Writing 0xFF to WDTCN locks out the disable feature. Once locked out, the disable operation is ignored until the
next system reset. Writing 0xFF does not enable or reset the watchdog timer. Applications always intending to use
the watchdog should write 0xFF to WDTCN in their initialization code.
Setting WDT Interval
WDTCN.[2:0] control the watchdog timeout interval. The interval is given by the following equation:
43+WDTCN[2:0] x TSYSCLK , (where TSYSCLK is the system clock period).
For a 2MHz system clock, this provides an interval range of 0.032msec to 524msec. WDTCN.7 must be a 0 when
setting this interval. Reading WDTCN returns the programmed interval. WDTCN.[2:0] is 111b after a system
reset.
Figure 13.3. WDTCN: Watchdog Timer Control Register
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
xxxxx111
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xFF
Bits7-0: WDT Control
Writing 0xA5 both enables and reloads the WDT.
Writing 0xDE followed within 4 clocks by 0xAD disables the WDT.
Writing 0xFF locks out the disable feature.
Bit4: Watchdog Status Bit (when Read)
Reading the WDTCN.[4] bit indicates the Watchdog Timer Status.
0: WDT is inactive
1: WDT is active
Bits2-0: Watchdog Timeout Interval Bits
The WDTCN.[2:0] bits set the Watchdog Timeout Interval. When writing these bits,
WDTCN.7 must be set to 0.
97 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 13.4. RSTSRC: Reset Source Register
R R/W R/W R/W R R R/W R Reset Value
JTAGRST CNVRSEF C0RSEF SWRSEF WDTRSF MCDRSF PORSF PINRSF xxxxxxxx
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xEF
(Note: Do not use read-modify-write operations on this register.)
Bit7: JTAGRST. JTAG Reset Flag.
0: JTAG is not currently in reset state.
1: JTAG is in reset state.
Bit6: CNVRSEF: Convert Start Reset Source Enable and Flag
Write
0: CNVSTR is not a reset source
1: CNVSTR is a reset source (active low)
Read
0: Source of prior reset was not from CNVSTR
1: Source of prior reset was from CNVSTR
Bit5: C0 RSEF: Comparator 0 Reset Enable and Flag
Write
0: Comparator 0 is not a reset source
1: Comparator 0 is a reset source (active low)
Read
N
ote: The value read from C0RSEF is not defined if Comparator 0 has not been enabled as
a reset source.
0: Source of prior reset was not from Comparator 0
1: Source of prior reset was from Comparator 0
Bit4: SW RSF: Software Reset Force and Flag
Write
0: No Effect
1: Forces an internal reset. /RST pin is not effected.
Read
0: Prior reset source was not from write to the SWRSF bit.
1: Prior reset source was from write to the SWRSF bit.
Bit3: WDTRSF: Watchdog Timer Reset Flag
0: Source of prior reset was not from WDT timeout.
1: Source of prior reset was from WDT timeout.
Bit2: MCDRSF: Missing Clock Detector Flag
0: Source of prior reset was not from Missing Clock Detector timeout.
1: Source of prior reset was from Missing Clock Detector timeout.
Bit1: PORSF: Power-On Reset Force and Flag
Write
0: No effect
1: Forces a Power-On Reset. /RST is driven low.
Read
0: Source of prior reset was not from POR.
1: Source of prior reset was from POR.
Bit0: PINRSF: HW Pin Reset Flag
0: Source of prior reset was not from /RST pin.
1: Source of prior reset was from /RST pin.
Rev. 1.7 98
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Table 13.1. Reset Electrical Characteristics
-40C to +85C unless otherwise specified.
PARAMETER CONDITIONS MIN TYP MAX UNITS
/RST Output Low Voltage IOL = 8.5mA, VDD = 2.7 to 3.6V 0.6 V
/RST Input High Voltage 0.7 x
VDD V
/RST Input Low Voltage 0.3 x
VDD V
/RST Input Leakage Current /RST = 0.0V 20 A
VDD for /RST Output Valid 1.0 V
AV+ for /RST Output Valid 1.0 V
VDD POR Threshold (VRST) 2.40 2.55 2.70 V
Reset Time Delay /RST rising edge after crossing reset
threshold 80 100 120 ms
Missing Clock Detector
Timeout Time from last system clock to reset
generation 100 220 500 s
99 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
14. OSCILLATOR
Each MCU includes an internal oscillator and an external oscillator drive circuit, either of which can generate the
system clock. The MCUs boot from the internal oscillator after any reset. The internal oscillator starts up instantly.
It can be enabled/disabled and its frequency can be changed using the Internal Oscillator Control Register
(OSCICN) as shown in Figure 14.2. The internal oscillator’s electrical specifications are given in Table 14.1.
Both oscillators are disabled when the /RST pin is held low. The MCUs can run from the internal oscillator or
external oscillator, and switch between the two at will u sing the CLKSL bit in the OSCICN Register. The external
oscillator requires an external resonator, parallel-mode crystal, capacitor, or RC network connected to the
XTAL1/XTAL2 pins (see Figure 14.1). The oscillator circuit must be configured for one of these sources in the
OSCXCN register. An external CMOS clock can also provide the system clock via overdriving the XTAL1 pin.
The XTAL1 and XTAL2 pins are 3.6V (not 5V) tolerant. The external oscillator can be left enabled and running
even when the MCU has switch ed to using the intern al oscillator.
Figure 14.1. Oscillator Diagram
OSC
In te rn a l C lo c k
Generator
SYSCLK
Input
Circuit
OSCXCN
EN
XTLVLD
XOSCMD2
XOSCMD1
XOSCMD0
XFCN2
XFCN1
XFCN0
OSCICN
MSCLKE
IFRDY
CLKSL
IOSCEN
IFCN1
IFCN0
XTAL1
XTAL2
opt. 1
opt. 2
opt. 4 op t. 3
XTAL1
XTAL2
XTAL1XTAL1
AV+
AGND
VDD
AV+
Rev. 1.7 100
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 14.2. OSCICN: Internal Oscillator Control Register
R/W R/W R/W R R/W R/W R/W R/W Reset Value
MSCLKE - - IFRDY CLKSL IOSCEN IFCN1 IFCN0 00000100
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xB2
Table 14.1. Internal Oscillator Electrical Characteristics
-40C to +85C unless otherwise specified.
PARAMETER CONDITIONS MIN TYP MAX UNITS
Internal Oscillator
Frequency OSCICN.[1:0] = 00
OSCICN.[1:0] = 01
OSCICN.[1:0] = 10
OSCICN.[1:0] = 11
1.5
3.1
6.2
12.3
2
4
8
16
2.4
4.8
9.6
19.2
MHz
Internal Oscillator Current
Consumption (from VDD) OSCICN.2 = 1 200 A
Internal Oscillator
Temperature Stability 4
ppm/C
Internal Oscillator Power
Supply (VDD) Stability 6.4 %/V
Bit7: MSCLKE: Missing Clock Enable Bit
0: Missing Clock Detector Disabled
1: Missing Clock Detector Enabled; triggers a reset if a missing clock is detected
Bits6-5: UNUSED. Read = 00b, W r ite = don’t care
Bit4: IFRDY: In ternal Oscillator Frequency Ready Flag
0: Internal Oscillator Frequency not running at speed specified by the IFCN bits.
1: Internal Oscillator Frequency running at speed specified by the IFCN bits.
Bit3: CLKSL: System Clock Source Select Bit
0: Uses Internal Oscillator as System Clock.
1: Uses External Oscillator as System Clock.
Bit2: IOSCEN: In ternal Oscillator Enable Bit
0: Internal Oscillator Disabled
1: Internal Oscillator Enabled
Bits1-0: IFCN1-0: Internal Oscillato r Frequency Control Bits
00: Internal Oscillator typical frequency is 2 MHz.
01: Internal Oscillator typical frequency is 4 MHz.
10: Internal Oscillator typical frequency is 8 MHz.
11: Internal Oscillator typical frequency is 1 6MHz.
101 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 14.3. OSCXCN: External Oscillator Control Register
R R/W R/W R/W R/W R/W R/W R/W Reset Value
XTLVLD XOSCMD2 XOSCMD1 XOSCMD0 - XFCN2 XFCN1 XFCN0 00110000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xB1
Bit7: XTLVLD: Crystal Oscillato r Valid Flag
(Valid only when XOSCMD = 1xx.)
0: Crystal Oscillator is unused or not yet stable
1: Crystal Oscillator is running and stable (should read 1ms after Crystal Oscillator is
enabled to avoid transient condition).
Bits6-4: XOSCMD2-0: External Oscillator Mode Bits
00x: Off. XTAL1 pin is grounded internally.
010: System Clock from External CMOS Clock on XTAL1 pin.
011: System Clock from External CMOS Clock on XTAL1 pin divided by 2.
10x: RC/C Oscillator Mode with divide by 2 stage.
110: Crystal Oscillator Mode
111: Crystal Oscillator Mode with divide by 2 stage.
Bit3: RESERVED. Read = undefined, Write = don’t care
Bits2-0: XFCN2-0: External Oscillato r Frequency Control Bits
000-111: see table below
XFCN Crystal (XOSCMD =
11x) RC (XOSCMD = 10x) C (XOSCMD = 10x)
000 f 12.5kHz f 25kHz K Factor = 0.44
001 12.5kHz < f 30.3kHz 25kHz < f 50kHz K Factor = 1.4
010 30.35kHz < f 93.8kHz 50kHz < f 100kHz K Factor = 4.4
011 93.8kHz < f 267kHz 100kHz < f 200kHz K Factor = 13
100 267kHz < f 722kHz 200kHz < f 400kHz K Factor = 38
101 722kHz < f 2.23MHz 400kHz < f 800kHz K Factor = 100
110 2.23MHz < f 6.74MHz 800kHz < f 1.6MHz K Factor = 420
111 f > 6.74MHz 1.6MHz < f 3.2MHz K Factor = 1400
CRYSTAL MODE (Circuit from Figure 14.1, Option 1; XOSCMD = 11x)
Choose XFCN value to match the crystal or ceramic resonator frequency.
RC MODE (Circuit from Figure 14.1, Option 2; XOSCMD = 10x)
Choose oscillation frequency range where:
f = 1.23(103) / (R * C), where
f = frequency of oscillatio n in MHz
C = capacitor value in pF
R = Pull-up resistor value in k
C MODE (Circuit from Figure 14.1, Option 3; XOSCMD = 10x)
Choose K Factor (KF) for the oscillation frequency desired:
f = KF / (C * AV+), where
f = frequency of oscillatio n in MHz
C = capacitor value on XTAL1, XTAL2 pins in pF
AV+ = Analog Power Supply on MCU in volts
Rev. 1.7 102
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
14.1. External Crystal Example
If a crystal or ceramic resonator were used to generate th e system clock for the MCU, the circuit would be as shown
in Figure 14.1, Option 1. For an ECS-110.5-20-4 crystal, the resonate frequency is 11.0592MHz, the intrinsic
capacitance is 7pF, and the ESR is 60. The compensation capacitors should be 33pF each, and the PWB parasitic
capacitance is estimated to be 2pF. The appropr iate External Oscillator Frequency Control valu e (XFCN) from the
Crystal column in the table in Figure 14.3 (OSCXCN Register) should be 111b.
Because the oscillator detect circuitry needs time to settle after the crystal oscillator is enabled, software should wait
at least 1ms between enabling the crystal o s cillator and polling the XTLVLD bit. The recommend procedure is:
1. Enable the external oscillator
2. Wait at least 1 ms
3. Poll for XTLVLD '0' ==> '1'
4. Switch to the external oscillator
Switching to the external oscillator before the crystal oscillator has stabilized could result in unpredictable behavior.
NOTE: Crystal oscillator circuits are quite sensitive to PCB layout. The crystal should be placed as close as possible
to the XTAL pins on the device, keeping the traces as short as possible and shielded with ground plane from any
other traces which could introduce noise or interference.
14.2. External RC Example
If an external RC network were used to generate the system clock for the MCU, the circuit would be as shown in
Figure 14.1, Option 2. The capacitor must be no greater than 100pF, but using a very small capacitor will increase
the frequency drift due to the PW B parasitic capacitance. To determine the required External Oscillator Freq uency
Control value (XFCN) in the OSCXCN Register, first select the RC network value to produce the desired frequency
of oscillation. If the frequency desired is 100kHz, let R = 246k and C = 50pF:
f = 1.23(103)/RC = 1.23(103) / [246 * 50] = 0.1MHz = 100kHz
XFCN log2(f/25kHz)
XFCN log2(100kHz/25kHz) = log2(4)
XFCN 2, or code 010
14.3. External Capacitor Example
If an external capacitor were used to generate the system clock for the MCU, the circuit would be as shown in
Figure 14.1, Option 3. The capacitor must be no greater than 100pF, but using a very small capacitor will increase
the frequency inaccuracy due to the PWB parasitic capacitance. To determine the required External Oscillator
Frequency Control value (XFCN) in the OSCXCN Register, select the capacitor to be used and find the frequency
of oscillation from the equations below. Assume AV+ = 3.0V and C = 50pF:
f = KF / (C * VDD) = KF / (50 * 3)
f = KF / 150
If a frequency of roughly 90kHz is desired, select the K Factor from the table in Figure 14.3 as KF = 13:
f = 13 /150 = 0.087MHz, or 87kHz
Therefore, the XFCN value to use in this example is 011.
103 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
15. PORT INPUT/OUTPUT
The MCUs have a wide array of digital resources, which are available through four digital I/O ports, P0, P1, P2 and
P3. Each of the pins on Ports 0, 1, and 2 can be defined as either its corresponding port I/O or one of the internal
digital resources assigned as shown in Figure 15.1. The designer has complete control over which functions are
assigned, limited only by the number of physical I/O pins available on the selected package (the
C8051F000/05/10/15 have all four ports pinned out, the F001/06/11/16 have P0 and P1, and the F002/07/12/17
have P0). This resource assignment flexibility is achieved through the use of a Priority CrossBar Decoder. (Note
that the state of a Port I/O pin can always be read in the corresponding Port latch regardless of the Crossbar
settings).
The CrossBar assigns the selected internal digital resources to the I/O pins based on the Priority Decode Table 15.1.
The registers XBR0, XBR1, and XBR2, defined in Figure 15.3, Figure 15.4, and Figure 15.5 are used to select an
internal digital function or let an I/O pin default to being a Port I/O. The crossbar functions identically for each
MCU, with the caveat that P2 is not pinned out on the F001/06/11/16, and both P1 and P2 are not pinned out on the
F002/07/12/17. Digital resources assigned to port pins that are not pinned out cannot be accessed.
All Port I/Os are 5V tolerant (Refer to Figure 15.2 for the port cell circuit.) The Port I/O cells are configured as
either push-pull or open-drain in the Port Configuration Registers (PRT0CF, PRT1CF, PRT2CF, PRT3CF).
Complete Electrical Specifications for Port I/O are given in Table 15.2.
15.1. Priority Cross Bar Decoder
One of the design goals of this MCU family was to make the entire palette of digital resources available to the
designer even on reduced pin count packages. The Priority CrossBar Decoder provides an elegant solution to the
problem of connecting the internal digital resources to the physical I/O pins.
The Priority CrossBar Decode (Table 15.1) assigns a priority to each I/O function, starting at the top with the
SMBus. As the table illustrates, when selected, its two signals will be assigned to Pin 0 and 1 of I/O Port 0. The
decoder always fills I/O bits from LSB to MSB starting with Port 0, then Port 1, finishing if necessary with Port 2.
If you choose not to use a resource, the next function down on the table will fill the priority slot. In this way it is
possible to choose only the functions required by the design, making full use of the available I/O pins. Also, any
extra Port I/O are grouped together for more convenient use in application code.
Registers XBR0, XBR1 and XBR2 are used to assign the digital I/O resources to the physical I/O Port pins. It is
important to understand that when the SMBus, SPI Bus, or UART is selected, the crossbar assigns all pins
associated with the selected bus. It would be impossible for instance to assign the RX pin from the UART function
without also assigning the TX function. Standard Port I/Os appear contiguously after the prioritized functions have
been assigned. For example, if you choose functions that take the first 14 Port I/O (P0.[7:0], P1.[5:0]), you would
have 18 Port I/O left unused by the crossbar (P1.[7:6], P2 and P3).
15.2. Port I/O Initialization
Port I/O initialization is straightforward. Registers XBR0, XBR1 and XBR2 must be loaded with the appropriate
values to select the digital I/O functions required by the design. Setting the XBARE bit in XBR2 to 1 enables the
CrossBar. Until the Crossbar is enabled, the external pins remain as standard Ports in input mode regardless
of the XBRn Register settings. For given XBRn Register settings, one can determine the I/O pin-out using the
Priority Decode Table; as an alternative, the Code Configuration Wizard function of the IDE software will
determine the Port I/O pin-assignments based on the XBRn Register settings.
The output driver characteristics of the I/O pins are defined using the Port Configuration Registers PRT0CF,
PRT1CF, PRT2CF and PRT3CF (see Figure 15.7, Figure 15.9, Figure 15.12, and Figure 15.14). Each Port Output
driver can be configured as either Open Drain or Push-Pull. This is required even for the digital resources selected
in the XBRn registers and is not automatic. The only exception to this is the SMBus (SDA, SCL) and UART
Receive (RX, when in mode 0) pins which are Open-drain regardless of the PRTnCF settings. When the
WEAKPUD bit in XBR2 is 0, a weak pu llup is enab led for all Port I/O configured as open-drain. WEAKPUD does
Rev. 1.7 104
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
not affect the push-pull Port I/O. Furthermore, the weak pullup is turned off on an open-drain output that is driving
a 0 to avoid unnecessary power dissipation.
The third and final step is to initialize the individual resources selected using the appropriate setup registers.
Initialization procedures for the various digital resources may be found in the detailed explanation of each available
function. The reset state of each register is shown in the figures that describe each individual register.
Figure 15.1. Port I/O Functional Block Diagram
Figure 15.2. Port I/O Cell Block Diagram
XBR0, XBR1,
XBR2 Registers
PRT3CF
Register
External
Pins
P0
P1
P2
8
8
8
(Internal Digital Signals)
Port
Latches
P3
P3
I/O
Cells
P3.0
Digital
Crossbar
Priority
Decoder
P1
I/O
Cells
SMBus
SPI
UART
PCA
T0, T1, T2,
T2EX,
/INT0,
/INT1
/SYSCLK
CNVSTR
P3.7
P1.0
P1.7
P2
I/O
Cells
P2.0
P2.7
P0
I/O
Cells
P0.0
P0.7
8
Highest
Priority
Lowest
Priority
Highest
Priority
Lowest
Priority
8
8
(P2.0-P2.7)
(P1.0-P1.7)
(P0.0-P0.7)
8
PRT0CF, PRT1CF,
PRT2CF Registers
(P3.0-P3.7)
Comptr.
Outputs
2
4
2
6
2
6
DGND
/PORT-OUTENABLE
PORT-OUTPUT
PORT-INPUT
PUSH-PULL VDD
VDD
VDD
WEAKPUD
PORT
PAD
(WEAK)
105 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Table 15.1. Crossbar Priority Decode
In the Priority Decode Table, a dot () is used to show the external Port I/O pin (column) to which each signal (row)
can be assigned by the user application code via programming registers XBR2, XBR1, and XBR0.
PIN I/O012345670123456701234567
SDA
SCL
SCK
MISO
MOSI
NSS
TX
RX
CEX0
CEX1
CEX2
CEX3
CEX4
ECI
CP0
CP1
T0
/INT0
T1
/INT1
T2
T2EX
/SYSCLK
CNVSTR
P0 P1 P2
Rev. 1.7 106
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 15.3. XBR0: Port I/O CrossBar Register 0
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
CP0OEN ECIE PCA0ME UARTEN SPI0OEN SMB0OEN 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xE1
Bit7: CP0 OEN: Comparator 0 Output Enab le Bit
0: CP0 unavailable at Port pin.
1: CP0 routed to Port Pin.
Bit6: ECIE: PCA0 Counter Input Enable Bit
0: ECI unavailable at Port pin.
1: ECI routed to Port Pin.
Bits3-5: PCA0ME: PCA Module I/O Enable Bits
000: All PCA I/O unavailable at Port pins.
001: CEX0 routed to Port Pin.
010: CEX0, CEX1 routed to 2 Port Pins.
011: CEX0, CEX1, CEX2 routed to 3 Port Pins.
100: CEX0, CEX1, CEX2, CEX3 routed to 4 Port Pins.
101: CEX0, CEX1, CEX2, CEX3, CEX4 routed to 5 Port Pins.
110: RESERVED
111: RESERVED
Bit2: UARTEN: UART I/O En able Bit
0: UART I/O unavailable at Port pins.
1: RX, TX routed to 2 Port Pins.
Bit1: SPI0 OEN: SPI Bus I/O Enable Bit
0: SPI I/O unavailable at Port pins.
1: MISO, MOSI, SCK, and NSS routed to 4 Port Pins.
Bit0: SMB0OEN: SMBus Bus I/O Enable Bit
0: SMBus I/O unavailable at P0.0, P0.1.
1: SDA routed to P0.0, SCL routed to P0.1.
107 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 15.4. XBR1: Port I/O CrossBar Register 1
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
SYSCKE T2EXE T2E INT1E T1E INT0E T0E CP1OEN 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xE2
Bit7: SYSCKE: SYSCLK Ou tput Enable Bit
0: SYSCLK unavailable at Port pin.
1: SYSCLK output routed to Port Pin.
Bit6: T2EXE: T2EX Enable Bit
0: T2EX unavailable at Port pin.
1: T2EX routed to Port Pin.
Bit5: T2 E: T2 Enable Bit
0: T2 unavailable at Port pin.
1: T2 routed to Port Pin.
Bit4: INT1 E: /INT1 Enable Bit
0: /INT1 unavailable at Port pin.
1: /INT1 routed to Port Pin.
Bit3: T1 E: T1 Enable Bit
0: T1 unavailable at Port pin.
1: T1 routed to Port Pin.
Bit2: INT0 E: /INT0 Enable Bit
0: /INT0 unavailable at Port pin.
1: /INT0 routed to Port Pin.
Bit1: T0 E: T0 Enable Bit
0: T0 unavailable at Port pin.
1: T0 routed to Port Pin.
Bit0: CP1OEN: Comparator 1 Output En able Bit
0: CP1 unavailable at Port pin.
1: CP1 routed to Port Pin.
Rev. 1.7 108
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 15.5. XBR2: Port I/O CrossBar Register 2
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
WEAKPUD XBARE - - - - - CNVSTE 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xE3
Bit7: WEAKPUD: Port I/O Weak Pull-up Disable Bit
0: Weak Pull-ups Enabled (except for Ports whose I/O are configured as push-pull)
1: Weak Pull-ups Disabled
Bit6: XBARE: Cro ssbar Enable Bit
0: Crossbar Disabled
1: Crossbar Enabled
Bits5-1: UNUSED. Read = 00000b, W rite = don’t care.
Bit0: CNVSTE: ADC Convert Start Input Enable Bit
0: CNVSTR unavailable at Port pin.
1: CNVSTR routed to Port Pin.
Example Usage of XBR0, XBR1, XBR2:
When selected, the digital resources fill the Port I/O pins in order (top to bottom as shown in
Table 15.1) starting with P0.0 through P0.7, and then P1.0 through P1.7, and finally P2.0
through P2.7. If the digital resources are not mapped to the Port I/O pins, they default to thei
r
matching internal Port Register bits.
Example1: If XBR0 = 0x11, XBR1 = 0x00, and XBR2 = 0x40:
P0.0=SDA, P0.1=SCL, P0.2=CEX0, P0.3=CEX1, P0.4 … P2.7 map to corresponding Port I/O.
Example2: If XBR0 = 0x80, XBR1 = 0x04, and XBR2 = 0x41:
P0.0=CP0, P0.1=/INT0, P0.2 = CNVSTR, P0.3 … P2.7 map to corresponding Port I/O.
109 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
15.3. General Purpose Port I/O
Each MCU has four byte-wide, bi-directional parallel ports that can be used general purpose I/O. Each port is
accessed through a corresponding special function register (SFR) that is both byte addressable and bit addressable.
When writing to a port, the value written to the SFR is latched to maintain the output data value at each pin. When
reading, the logic levels of the port’s input pins are returned regardless of the XBRn settings (i.e. even when the pin
is assigned to another signal by the Crossbar, the Port Register can always still read its corresponding Port I/O pin).
The exception to this is the execution of the read-modify-write instructions. The read-modify-write instructions
when operating on a port SFR are the following: ANL, ORL, XRL, JBC, CPL, INC, DEC, DJNZ and MOV, CLR
or SET, when the destin ation is an individu al bit in a port SFR. For th ese instructions, the value of the port register
(not the pin) is read, modified, and written b ack to the SFR.
15.4. Configuring Ports Which are not Pinned Out
P2 and P3 are not pinned out on the F001/06/11/16. P1, P2, and P3 are not pinned out on the F002/07/12/17. These
port registers (and corresponding interrupts, where applicable) are still available for software use in these reduced
pin count MCUs. Whether used or not in software, it is recommended not to let these port drivers go to high
impedance state. This is prevented after reset by having the weak pull-ups enabled as described in the XBR2
register. It is recommended that each output driver for ports not pinned out should be configured as push-pull using
the corresponding PRTnCF register. This will inhibit a high impedance state even if the weak pull-up is disabled.
Figure 15.6. P0: Port0 Register
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
P0.7 P0.6 P0.5 P0.4 P0.3 P0.2 P0.1 P0.0 11111111
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
(bit addressable) 0x80
Figure 15.7. PRT0CF: Port0 Configuration Register
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xA4
Bits7-0: P0.[7:0]
(Write – Output appears on I/O pins per XBR0, XBR1, and XBR2 Registers)
0: Logic Low Output.
1: Logic High Output (high-impedance if corresponding PRT0CF.n bit = 0)
(Read – Regardless of XBR0, XBR1, and XBR2 Register settings).
0: P0.n pin is logic low.
1: P0.n pin is logic high.
Bits7-0: PRT0CF.[7:0]: Output Configuration Bits for P0.7-P0.0 (respectively)
0: Corresponding P0.n Output mode is Open-Drain.
1: Corresponding P0.n Output mode is Push-Pull.
(Note: When SDA, SCL, and RX appear on any of the P0 I/O, each are open-drain
regardless of the value of PRT0CF).
Rev. 1.7 110
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 15.8. P1: Port1 Register
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
P1.7 P1.6 P1.5 P1.4 P1.3 P1.2 P1.1 P1.0 11111111
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
(bit addressable) 0x90
Figure 15.9. PRT1CF: Port1 Configuration Register
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xA5
Figure 15.10. PRT1IF: Port1 Interrupt Flag Register
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
IE7 IE6 IE5 IE4 - - - - 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xAD
Bits7-0: P1.[7:0]
(Write – Output appears on I/O pins per XBR0, XBR1, and XBR2 registers)
0: Logic Low Output.
1: Logic High Output (high-impedance if corresponding PRT1CF.n bit = 0)
(Read – Regardless of XBR0, XBR1, and XBR2 Register settings).
0: P1.n pin is logic low.
1: P1.n pin is logic high.
Bits7-0: PRT1CF.[7:0]: Output Configuration Bits for P1.7-P1.0 (respectively)
0: Corresponding P1.n Output mode is Open-Drain.
1: Corresponding P1.n Output mode is Push-Pull.
Bit7: IE7: External Interrupt 7 Pending Flag.
0: No falling edge detected on P1.7.
1: This flag is set by hardware when a falling edge on P1.7 is detected.
Bit6: IE6: External Interrupt 6 Pending Flag.
0: No falling edge detected on P1.6.
1: This flag is set by hardware when a falling edge on P1.6 is detected.
Bit5: IE5: External Interrupt 5 Pending Flag.
0: No falling edge detected on P1.5.
1: This flag is set by hardware when a falling edge on P1.5 is detected.
Bit4: IE4: External Interrupt 4 Pending Flag.
0: No falling edge detected on P1.4.
1: This flag is set by hardware when a falling edge on P1.4 is detected.
Bits3-0: UNUSED. Read = 0000b, W r ite = don’t care.
111 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 15.11. P2: Port2 Register
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
P2.7 P2.6 P2.5 P2.4 P2.3 P2.2 P2.1 P2.0 11111111
Bit7 Bit6 Bit Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
(bit addressable) 0xA0
Figure 15.12. PRT2CF: Port2 Configuration Register
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xA6
Bits7-0: P2.[7:0]
(Write – Output appears on I/O pins per XBR0, XBR1, and XBR2 registers)
0: Logic Low Output.
1: Logic High Output (high-impedance if corresponding PRT2CF.n bit = 0)
(Read – Regardless of XBR0, XBR1, and XBR2 Register settings).
0: P2.n is logic low.
1: P2.n is logic high.
Bits7-0: PRT2CF.[7:0]: Output Configuration Bits for P2.7-P2.0 (respectively)
0: Corresponding P2.n Output mode is Open-Drain.
1: Corresponding P2.n Output mode is Push-Pull.
Rev. 1.7 112
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 15.13. P3: Port3 Register
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
P3.7 P3.6 P3.5 P3.4 P3.3 P3.2 P3.1 P3.0 11111111
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
(bit addressable) 0xB0
Figure 15.14. PRT3CF: Port3 Configuration Register
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xA7
Table 15.2. Port I/O DC Electrical Characteristics
VDD = 2.7 to 3.6V, -40C to +85C unless otherwise specified.
PARAMETER CONDITIONS MIN TYP MAX UNITS
Output High Voltage IOH = -10uA, Port I/O push-pull
IOH = -3mA, Port I/O push-pull
IOH = -10mA, Port I/O push-pull
VDD –
0.1
VDD –
0.7
VDD –
0.8
V
Output Low Voltage IOL = 10uA
IOL = 8.5mA
IOL = 25mA
1.0
0.1
0.6
V
Input High Voltage 0.7 x
VDD V
Input Low Voltage 0.3 x
VDD V
Input Leakage Current DGND < Port Pin < VDD, Pin Tri-state
Weak Pull-up Off
Weak Pull-up On
30
1
A
Capacitive Loading 5 pF
Bits7-0: P3.[7:0]
(Write)
0: Logic Low Output.
1: Logic High Output (high-impedance if corresponding PRT3CF.n bit = 0)
(Read)
0: P3.n is logic low.
1: P3.n is logic high.
Bits7-0: PRT3CF.[7:0]: Output Configuration Bits for P3.7-P3.0 (respectively)
0: Corresponding P3.n Output mode is Open-Drain.
1: Corresponding P3.n Output mode is Push-Pull.
113 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
16. SMBus / I2C Bus
The SMBus serial I/O interface is compliant with the System Management Bus Specification, version 1.1. It is a
two-wire, bi-directional serial bus, which is also compatible with the I2C serial bus. Reads and writes to the
interface by the system controller are byte oriented with the SMBus interface autonomously controlling the serial
transfer of the data. Data can be transferred at up to 1/8th of the system clock if desired (this can be faster than
allowed by the SMBus specification, depending on the system clock used). A method of extending the clock-low
duration is used to accommodate devices with different speed capabilities on the same bus.
Two types of data transfers are possible: data transfers from a master transmitter to an addressed slave receiver, and
data transfers from an addressed slave transmitter to a master receiver. The master device initiates both types of
data transfers and provides the serial clock pulses. The SMBus interface may operate as a master or a slave.
Multiple master devices on the same bus are also supported. If two or more masters attempt to initiate a data
transfer simultaneously, an arbitration scheme is employed with a single master always winning the arbitration.
Figure 16.1. SMBus Block Diagram
SFR Bus
Data Path
Control
SFR Bus
Write to
SMB0DAT
SMBUS CONTROL LOGIC
Read
SMB0DAT
SMB0ADR
S
L
V
6G
C
S
L
V
5
S
L
V
4
S
L
V
3
S
L
V
2
S
L
V
1
S
L
V
0
C
R
O
S
S
B
A
R
Clock Divide
Logic
SYSCLK
SMB0CR
C
R
7
C
R
6
C
R
5
C
R
4
C
R
3
C
R
2
C
R
1
C
R
0
SCL
FILTER
N
SDA
Control
0000000b
7 MSBs 8
AB
A=B
8
01234567 SMB0DAT
8
SMB0CN
S
T
A
S
IA
AF
T
E
T
O
E
E
N
S
M
B
B
U
S
Y
S
T
O
SMB0STA
S
T
A
4
S
T
A
3
S
T
A
2
S
T
A
1
S
T
A
0
SCL
Control
Status Generation
Arbitration
SCL Synchronization
SCL Generation (Master Mode)
IRQ Generation
S
T
A
5
S
T
A
6
S
T
A
7
AB
A=B
SMBUS
IRQ
Interrupt
Request
Port I/O
1
0
SDA
FILTER
N
7
Rev. 1.7 114
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 16.2 shows a typical SMBus configuration. The SMBus interface will work at any voltage between 3.0V
and 5.0V and different devices on the bus may operate at different voltage levels. The SCL (serial clock) and SDA
(serial data) lines are bi-directional. They must be connected to a positive power supply voltage through a pull-up
resistor or similar circuit. When the bus is free, both lines are pulled high. Every device connected to the bus must
have an open-drain or open-collector output for both the SCL and SDA lines. The maximum number of devices on
the bus is limited only by the requirement that the rise and fall times on the bus will not exceed 300ns and 1000ns,
respectively.
Figure 16.2. Typical SMBus Configuration
16.1. Supporting Documents
It is assumed the reader is familiar with or has access to the following supporting documents:
1. The I2C-bus and how to use it (including specifications), Philips Semiconductor.
2. The I2C-Bus Specification -- Versio n 2.0, Philips Semiconductor.
3. System Management Bus Specification -- Version 1.1, SBS Implementers Forum.
VDD = 5V
Master
Device Slave
Device 1 Slave
Device 2
VDD = 3V VDD = 5V VDD = 3V
SDA
SCL
115 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
16.2. Operation
A typical SMBus transaction consists of a START condition, followed by an address byte, one or more bytes of
data, and a STOP condition. The address byte and each of the data bytes are followed by an ACKNOWLEDGE bit
from the receiver. The address byte consists of a 7-bit address plus a direction bit. The direction bit (R/W)
occupies the least-significant bit position of the address. The direction bit is set to logic 1 to indicate a “READ”
operation and cleared to logic 0 to indicate a “WRITE” operation. A general call address (0x00 +R/W) is
recognized by all slave devices allowing a master to address multiple slave devices simultaneously.
All transactions are initiated by the master, with one or more addressed slave devices as the target. The master
generates the START condition and then transmits the address and direction bit. If the transaction is a WRITE
operation from the master to the slave, the master transmits the data a byte at a time waiting for an
ACKNOWLEDGE from the slave at the end of each byte. If it is a READ operation, the slave transmits the data
waiting for an ACKNOWLEDGE from the master at the end of each byte. At the end of the data transfer, the
master generates a STOP condition to terminate the transaction and free the bus. Figure 16.3 illustrates a typical
SMBus transaction.
Figure 16.3. SMBus Transaction
The SMBus interface may be configured to operate as either a master or a slave. At any particular time, it will be
operating in one of the following four modes:
16.2.1. Master Transmitter Mode
Serial data is transmitted on SDA while the serial clock is output on SCL. The first byte transmitted contains the
address of the targ et slave device and the data directio n bit. In this case the data direction bit (R/W) will be logic 0
to indicate a “WRITE” operation. The master then transmits one or more bytes of serial data. After each byte is
transmitted, an acknowledge bit is generated by the slave. To indicate the beginning and the end of the serial
transfer, the master device outputs START and STOP conditions.
16.2.2. Master Receiver Mode
Serial data is received on SDA while the serial clock is output on SCL. The first byte is transmitted by the master
and contains the address of the target slave and the data d irection bit. In this case the data direction bit (R/W ) will
be logic 1 to indicate a “READ” operation. Serial data is then received from the slave on SDA while the master
outputs the serial clock. The slave transmits one or more bytes of serial data. After each byte is received, an
acknowledge bit is transmitted by the master. The master outputs START and STOP conditions to indicate the
beginning and end of the serial transfer.
16.2.3. Slave Transmitter Mode
Serial data is transmitted on SDA while the serial clock is received on SCL. First, a byte is received that contains an
address and data direction bit. In this case the data direction bit (R/W) will be logic 1 to indicate a “READ”
operation. If the received address matches the slave’s assigned address (or a general call address is received) one or
more bytes of serial data are transmitted to the master. After each byte is received, an acknowledge bit is
transmitted by the master. The master outputs START and STOP conditions to indicate the beginning and end of
the serial transfer.
START SLAVE ADDR R/W ACK DATA ACK NACK STOP DATA
Time
Rev. 1.7 116
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
16.2.4. Slave Receiver Mode
Serial data is received on SDA while the serial clock is received on SCL. First, a byte is received that contains an
address and data direction bit. In this case the data direction bit (R/W) will be logic 0 to indicate a “WRITE”
operation. If the received address matches the slave’s assigned address (or a general call address is received) one or
more bytes of serial data are received from the master. After each byte is received, an acknowledge bit is
transmitted by the slave. The master outputs START and STOP conditions to indicate the beginning and end of the
serial transfer.
16.3. Arbitration
A master may start a transfer only if the bus is free. The bus is free after a STOP condition or after the SCL and
SDA lines remains high for a specified time. Two or more master devices may attempt to generate a START
condition at the same time. Since the devices that generated the START condition may not be aware that other
masters are contending for the bus, an arbitration scheme is employed. The master devices continue to transmit
until one of the masters transmits a HIGH level, while the other(s) master transmits a LOW level on SDA. The first
master(s) transmitting the HIGH level on SDA looses the arbitration and is required to give up the bus.
16.4. Clock Low Extension
SMBus provides a clock synchronization mechanism, similar to I2C, which allows devices with different speed
capabilities to coexist on the bus. A clock-low extension is used during a transfer in order to allow slower slave
devices to communicate with faster masters. The slave can hold the SCL line LOW to extend the clock low period,
effectively decreasing the serial clock frequency.
16.5. Timeouts
16.5.1. SCL Low Timeout
If the SCL line is held low by a slave device on the bus, no further communication is possible. Furthermore, the
master cannot force the SCL line high to correct the error condition. To solve this problem, the SMBus protocol
specifies that devices participating in a transfer must detect any clock cycle held low longer than 25ms as a
“timeout” condition. Devices that have detected the timeout condition must reset the communication no later than
10ms after detecting the timeout condition.
One of the MCU’s general-purpose timers, operating in 16-bit auto-reload mode, can be used to monitor the SCL
line for this timeout condition. Timer 3 is specifically designed for this purpose. (Refer to the Timer 3 Section
19.3. for detailed information on Timer 3 operation.)
16.5.2. SCL High (SMBus Free) Timeout
The SMBus specification stipulates that if a device holds the SCL and SDA lines high for more that 50usec, the bus
is designated as free. The SMB0CR reg ister is u sed to detect this conditio n when the FTE bit in SMB0CN is set.
16.6. SMBus Special Function Registers
The SMBus serial interface is accessed and controlled through five SFRs: SMB0CN Control Register, SMB0CR
Clock Rate Register, SMB0ADR Address Register, SMB0DAT Data Register and SMB0STA Status Register. The
system device may have one or more SMBus serial interfaces implemented. The five special function registers
related to the operation of the SMBus interface are described in the following section.
117 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
16.6.1. Control Register
The SMBus Control register SMB0CN is used to configure and control the SMBus interface. All of the bits in the
register can be read or written by software. Two of the control bits are also affected by the SMBus hardware. The
Serial Interrupt flag (SI, SMB0CN.3) is set to logic 1 by the hardware when a valid serial interrupt condition occurs.
It can only be cleared by software. The Stop flag (STO, SMB0CN.4) is cleared to logic 0 by hardware when a
STOP condition is present on the bus.
Setting the ENSMB flag to logic 1 enables the SMBus interface. Clearing the ENSMB flag to logic 0 disables the
SMBus interface and removes it from the bus. Momentarily clearing the ENSMB flag and then resetting it to logic
1 will reset a SMBus communication. However, ENSMB should not be used to temporarily remove a device from
the bus since the bus state information will be lost. Instead, the Assert Acknowledge (AA) flag should be used to
temporarily remove the device from the bus (see description of AA flag below).
Setting the Start flag (STA, SMB0CN.5) to logic 1 will put the SMBus in a master mode. If the bus is free, the
SMBus hardware will generate a START condition. If the bus is not free, the SMBus hardware waits for a STOP
condition to free the bus and then generates a START condition after a 5s delay per the SMB0CR value. (In
accordance with the SMBus protocol, the SMBus interface also considers the bus free if the bus is idle for 50s and
no STOP condition was recognized.) If STA is set to logic 1 while the SMBus is in master mode and one or more
bytes have been transferred, a repeated START condition will be generated. To ensure proper operation, the STO
flag should be explicitly cleared before setting STA to a logic 1.
When the Stop flag (STO, SMB0CN.4) is set to logic 1 while the SMBus interface is in master mode, the hardware
generates a STOP condition on the SMBus. In a slave mode, the STO flag may be used to recover from an error
condition. In this case, a STOP condition is not generated on the SMBus, but the SMBus hardware behaves as if a
STOP condition has been received and enters the “not addressed” slave receiver mode. The SMBus hardware
automatically clears the STO flag to logic 0 when a STOP condition is detected on the bus.
The Serial Interrupt flag (SI, SMB0CN.3) is set to logic 1 by hardware when the SMBus interface enters one of 27
possible states. If interrupts are enabled for the SMBus interface, an interrupt request is generated when the SI flag
is set. The SI flag must be cleared by software. While SI is set to logic 1, the clock-low period of the serial clock
will be stretched and the serial transfer is su spended.
The Assert Acknowledge flag (AA, SMB0CN.2) is used to set the level of the SDA line during the acknowledge
clock cycle on the SCL line. Setting the AA flag to logic 1 will cause an ACKNOWLEDGE (low level on SDA) to
be sent during the acknowledge cycle if the device has been addressed. Setting the AA flag to logic 0 will cause a
NOT ACKNOWLEDGE (high level on SDA) to be sent during acknowledge cycle. After the transmission of a
byte in slave mode, the slave can be temporarily removed from the bus by clearing the AA flag. The slave’s own
address and general call address will be ignored. To resume operation on the bus, the AA flag must be reset to logic
1 to allow the slave’s address to be recognized.
Setting the SMBu s Free Timer Enable bit (FTE, SMB0CN.1) to logic 1 enables the SMBus Free Timeout feature. If
SCL and SDA remain high for the SMBus Free Timeout given in the SMBus Clock Rate Register (Figure 16.5), the
bus will be considered free and a Start will be generated if pending. The bus free period should be greater than
50s.
Setting the SMBus timeout enable bit (TOE, SMB0CN.0) to logic 1 enables Timer 3 to count up when the SCL line
is low and Timer 3 is enabled. If Timer 3 overflow s, a Timer 3 interrup t will b e g enerated, which will alert the CPU
that a SMBus SCL low timeout has occurred.
Rev. 1.7 118
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 16.4. SMB0CN: SMBus Control Register
R R/W R/W R/W R/W R/W R/W R/W Reset Value
BUSY ENSMB STA STO SI AA FTE TOE 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
(bit addressable) 0xC0
Bit7: BUSY: Bu sy Status Flag.
0: SMBus is free
1: SMBus is busy
Bit6: ENSMB: SMBu s Enable.
This bit enables/disables the SMBus serial interface.
0: SMBus disabled.
1: SMBus enabled.
Bit5: STA: SMBus Start Flag.
0: No START condition is tran smitted.
1: When operating as a master, a START condition is transmitted if the bus is free. (If the
b
us is not free, the START is transmitted after a STOP is received.) If STA is set after one
or more bytes have been transmitted or received and before a STOP is received, a repeated
START condition is transmitted. STO should be explicitly cleared before setting STA to
logic 1.
Bit4: STO: SMBus Stop Flag.
0: No STOP condition is transmitted.
1: Setting STO to logic 1 causes a STOP co ndition to be transmitted. Wh en a STOP
condition is received, hardware clears STO to logic 0. If both STA and STO are set, a
STOP condition is transmitted followed by a START condition. In slave mode, setting the
STO flag causes SMBus to behave as if a STOP condition was received.
Bit3: SI: SMBus Serial Interrupt Flag.
This bit is set by hardware when one of 27 possible SMBus states is entered. (Status code
0xF8 does not cau se SI to be set.) When the SI interrupt is enabled, setting this b it causes
the CPU to vector to th e SMBus interrupt service routin e. This bit is not automatically
cleared by hardware and must be cleared by software.
Bit2: AA: SMBus Assert Acknowledge Flag.
This bit defines the type of acknowledge returned during the acknowledge cycle on the
SCL line.
0: A “not acknowledge” (high level on SDA) is returned during the acknowledge cycle.
1: An “acknowledge” (low level on SDA) is returned during the acknowledge cycle.
Bit1: FTE: SMBu s Free Timer Enable Bit
0: No timeout when SCL is high
1: Timeout when SCL high time exceeds limit specified by the SMB0CR value.
Bit0: TOE: SMBu s Timeout En able Bit
0: No timeout when SCL is low.
1: Timeout when SCL low time exceeds limit specified by Timer 3, if enabled.
119 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
16.6.2. Clock Rate Register
Figure 16.5. SMB0CR: SMBus Clock Rate Register
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xCF
Bits7-0: SMB0CR.[7:0]: SMBu s Clock Rate Preset
The SMB0CR Clock Rate register controls the frequency of the serial clock SCL in maste
r
mode. The 8-bit word stored in the SMB0CR Register preloads a dedicated 8-
b
it timer.
The timer counts up, and when it rolls over to 0x00, the SCL logic state toggles.
The SMB0CR setting should be bounded by the following equation, where SMB0CR is the
unsigned 8-bit value in register SMB0CR, and SYSCLK is the system clock frequency in
Hz: SMB0CR < ((288 - 0.85 * SYSCLK) / 1.125E6)
The resulting SCL signal high and low times are given by the following equations:
TLOW = (256 – SMB0CR) / SYSCLK
THIGH
(258 – SMB0CR) / SYSCLK + 625 ns
Using the same value of SMB0CR from above, the Bus Free Timeout period is given in the
following equation:
TBFT
10 * [(256 – SMB0CR) + 1] / SYSCLK
Rev. 1.7 120
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
16.6.3. Data Register
The SMBus Data register SMB0DAT holds a byte of serial data to be transmitted or one that has just been received.
Data remains stable in the register as long as SI is set to logic 1. Software can safely read or write to the data
register when the SI flag is set. Software should not attempt to access the SMB0DAT register when the SMBus is
enabled and the SI flag is cleared to logic 0 since the hardware may be in the process of shifting a byte of data in or
out of the register.
Data in SMB0DAT is always shifted out MSB first. After a byte has been received, the first bit of received data is
located at the MSB of SMB0DAT. While data is being shifted out, data on the bus is simultaneously being shifted
in. Therefore, SMB0DAT always contains the last data byte present on the bus. Thus, in the event of lost arb itration,
the transition from master transmitter to slave receiver is made with the correct data in SMB0DAT.
Figure 16.6. SMB0DAT: SMBus Data Register
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xC2
16.6.4. Address Register
The SMB0ADR Address register holds the slave address for the SMBus interface. In slave mode, the seven most-
significant bits hold the 7-bit slave address. The least significant bit, bit 0, is used to enable the recognition of the
general call address (0x00). If bit 0 is set to logic 1, the general call address will be recognized. Otherwise, the
general call address is ignored. The contents of this register are ignored when the SMBus hardware is operating in
master mode.
Figure 16.7. SMB0ADR: SMBus Address Register
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
SLV6 SLV5 SLV4 SLV3 SLV2 SLV1 SLV0 GC 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xC3
Bits7-1: SLV6-SLV0: SMBus Slave Address.
These bits are loaded with the 7-bit slave address to which the SMBus will respond when
operating as a slave transmitter or slave receiver. SLV6 is the most significant bit of the
address and corresponds to the first bit of the address byte received on the SMBus.
Bit0: GC: Gen eral Call Address Enable.
This bit is used to enable general call address (0x00) recognition.
0: General call address is ignored.
1: General call address is recognized.
Bits7-0: SMB0DAT: SMBus Data.
The SMB0DAT register contains a byte of data to be transmitted on the SMBus serial
interface or a byte that has just been received on the SMBus serial interface. The CPU can
read from or write to this register whenever the SI serial interrupt flag (SMB0CN.3) is set
to logic one. The serial data in the register remains stable as long as the SI flag is set.
When the SI flag is not set, the system may be in the process of shifting data in/out and the
CPU should not attempt to access this register.
121 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
16.6.5. Status Register
The SMB0STA Status register holds an 8-bit status code indicating the current state of the SMBus. There are 28
possible SMBus states, each with a corresponding unique status code. The five most significant bits of the status
code vary while the three least-significant bits of a valid status code are fixed at zero when SI = 1. Therefore, all
possible status codes are multiples of eight. This facilitates the use of status codes in software as an index used to
branch to appropriate service routines (allowing 8 bytes of code to service the state or jump to a more extensive
service routine).
For the purposes of user software, the contents of the SMB0STA register is only defined when the SI flag is logic 1.
Software should never write to the SMB0STA register. Doing so will yield indeterminate results. The 28 SMBus
states, along with their corresponding status codes, are given in Table 16.1.
Figure 16.8. SMB0STA: SMBus Status Register
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
STA7 STA6 STA5 STA4 STA3 STA2 STA1 STA0 11111000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xC1
Bits7-3: STA7-STA3: SMBus Status Code.
These bits contain the SMBus Status Code. There are 28 possible status codes. Each
status code corresponds to a single SMBus state. A valid status code is present in
SMB0STA when the SI flag (SMB0CN.3) is set. The content of SMB0STA is not defined
when the SI flag is logic 0. Writing to the SMB0STA register at any time will yield
indeterminate results.
Bits2-0: STA2-STA0: The three least significant bits of SMB0STA are always read as logic 0 when
the SI flag is logic 1.
Rev. 1.7 122
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Table 16.1. SMBus Status Codes
Status Code
(SMB0STA) Mode SMBus State
0x00 All Bus Error (i.e. illegal START, illegal STOP, …)
0x08 Master Transmitter/Receiver START condition transmitted.
0x10 Master Transmitter/Receiver Repeated START condition transmitted.
0x18 Master Transmitter Slave address + W transmitted. ACK received.
0x20 Master Transmitter Slave address + W transmitted. NACK received.
0x28 Master Transmitter Data byte transmitted. ACK received.
0x30 Master Transmitter Data byte transmitted. NACK received.
0x38 Master Transmitter Arbitration lost
0x40 Master Receiver Slave address + R transmitted. ACK received.
0x48 Master Receiver Slave address + R transmitted. NACK received
0x50 Master Receiver Data byte received. ACK transmitted.
0x58 Master Receiver Data byte received. NACK transmitted.
0x60 Slave Receiver SMB0’s own slave address + W received. ACK transmitted.
0x68 Slave Receiver Arbitration lost in transmitting slave address + R/W as master.
Own slave address + W received. ACK transmitted.
0x70 Slave Receiver General call address (0x00) received. ACK returned.
0x78 Slave Receiver Arbitration lost in transmitting slave address + R/W as master.
General call address received. ACK transmitted.
0x80 Slave Receiver SMB0’s own slave address + W received. Data byte received.
ACK transmitted.
0x88 Slave Receiver SMB0’s own slave address + W received. Data byte received.
NACK transmitted.
0x90 Slave Receiver General call address (0x00) received. Data byte received. ACK
transmitted.
0x98 Slave Receiver General call address (0x00) received. Data byte received.
NACK transmitted.
0xA0 Slave Receiver A STOP or repeated START received while addressed as a slave.
0xA8 Slave Transmitter SMB0’s own slave address + R received. ACK transmitted.
0xB0 Slave Transmitter Arbitration lost in transmitting slave address + R/W as master.
Own slave address + R received. ACK transmitted.
0xB8 Slave Transmitter Data byte transmitted. ACK received.
0xC0 Slave Transmitter Data byte transmitted. NACK received.
0xC8 Slave Transmitter Last data byte transmitted (AA=0). ACK received.
0xD0 Slave Transmitter/Receiver SCL Clock High Timer per SMB0CR timed out (FTE=1)
0xF8 All Idle
123 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
17. SERIAL PERIPHERAL INTERFACE BUS
The Serial Peripheral Interface (SPI) provides access to a four-wire, full-duplex, serial bus. SPI supports the
connection of multiple slave devices to a master device on the same bus. A separate slave-select signal (NSS) is
used to select a slave device an d enable a data transfer between the master and th e selected slave. Multiple masters
on the same bus are also supported. Collision detection is provided when two or more masters attempt a data
transfer at the same time. The SPI can operate as either a master or a slave. When the SPI is configured as a
master, the maximum data transfer rate (bits/sec) is one-half the system clock frequency.
When the SPI is configured as a slave, the maximum data transfer rate (bits/sec) for full-duplex operation is 1/10 the
system clock frequency, provided that the master issues SCK, NSS, and the serial input data synchronously with the
system clock. If the master issues SCK, NSS, and the serial input data asynchronously, the maximum data transfer
rate (bits/sec) must be less that 1/10 the system clock frequency. In the special case where the master only wants to
transmit data to the slave and does not need to receive data from the slave (i.e. half-duplex operation), the SPI slave
can receive data at a maximum data transfer rate (bits/sec) of ¼ the system clock frequency. This is provided that
the master issues SCK, NSS, and the serial input data synchronously with the system clock.
Figure 17.1. SPI Block Diagram
SFR Bus
Clock Divide
Logic
Data Path
Control
SFR Bus
Write to
SPI0DAT
Receive Data Register
SPI0DAT
01234567
Shift Register
SPI CONTROL LOGIC
Bit Count
Logic
SPI0CKR
S
C
R
7
S
C
R
6
S
C
R
5
S
C
R
4
S
C
R
3
S
C
R
2
S
C
R
1
S
C
R
0
SPI0CFG
C
K
P
H
A
C
K
P
O
L
B
C
2
B
C
1
B
C
0
F
R
S
2
F
R
S
1
F
R
S
0
SPI0CN
M
O
D
F
T
X
B
S
Y
S
L
V
S
E
L
M
S
T
E
N
S
P
I
E
N
W
C
O
L
S
P
I
F
R
X
O
V
R
N
Pin Control
Interface
SPI Clock
(Master Mode)
Pin
Control
Logic
C
R
O
S
S
B
A
R
Port I/O
Read
SPI0DAT
SPI IRQ
SYSCLK
Tx Data
Rx Data
SCK
MOSI
MISO
NSS
Rev. 1.7 124
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 17.2. Typical SPI Interconnection
17.1. Signal Descriptions
The four signals used by the SPI (MOSI, MISO, SCK, NSS) are described below.
17.1.1. Master Out, Slave In
The master-out, slave-in (MOSI) signal is an output from a master device and an input to slave devices. It is used to
serially transfer data from the master to the slave. Data is transferred most-significant bit first.
17.1.2. Master In, Slave Out
The master-in, slave-out (MISO) signal is an output from a slave device and an input to the master device. It is used
to serially transfer data from the slave to the master. Data is transferred most-significant bit first. A SPI slave
places the MISO pin in a high-impedance state when the slave is not selected.
17.1.3. Serial Clock
The serial clock (SCK) signal is an output from the master device and an input to slave devices. It is used to
synchronize the transfer of data between the master and slave on the MOSI and MISO lines.
17.1.4. Slave Select
The slave select (NSS) signal is an input used to select the SPI module when in slave mode by a master, or to
disable the SPI module when in master mode. When in slave mode, it is pulled low to initiate a data transfer and
remains low for the duration of the transfer.
Master
Device
MOSI
Slave
Device
NSS
Slave
Device
NSS
Slave
Device
MISO
SCK
Port I/O
NSS
VDD
Port I/O
Port I/O
125 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
17.2. Operation
Only a SPI master device can initiate a data transfer. The SPI is placed in master mode by setting the Master Enable
flag (MSTEN, SPI0CN.1). Writing a byte of data to the SPI data register (SPI0DAT) when in Master Mode starts a
data transfer. The SPI master immediately shifts out the data serially on the MOSI line while providing the serial
clock on SCK. The SPIF (SPI0CN.7) flag is set to logic 1 at the end of the transfer. If interrupts are enabled, an
interrupt request is generated when the SPIF flag is set. The SPI master can be configured to shift in/out from one
to eight bits in a transfer operation in order to accommodate slave devices with different word lengths. The SPIFRS
bits in the SPI Configuration Register (SPI0CFG.[2:0]) are used to select the number of bits to shift in/out in a
transfer operation.
While the SPI master transfers data to a slave on the MOSI line, the addressed SPI slave device simultaneously
transfers the contents of its shift register to the SPI master on the MISO line in a full-duplex operation. The data
byte received from the slave replaces the data in the master’s data register. Therefore, the SPIF flag serves as both a
transmit-complete and receive-data-ready flag. The data transfer in both directions is synchronized with the serial
clock generated by the master. Figure 17.3 illustrates the full-duplex operation of an SPI master and an addressed
slave.
Figure 17.3. Full Duplex Operation
The SPI data register is double buffered on reads, but not on a write. If a write to SPI0DAT is attempted during a
data transfer, the WCOL flag (SPI0CN.6) will be set to logic 1 and the write is ignored. The current data transfer
will continue uninterrupted. A read of the SPI data register by the system controller actually reads the receive
buffer. If the receive buffer still holds unread data from a previous transfer when the last bit of the current transfer
is shifted into the SPI shift register, a receive overrun occurs and the RXOVRN flag (SPI0CN.4) is set to logic 1.
The new data is not transferred to the receive buffer, allowing the previously received data byte to be read. The data
byte causing the overrun is lost.
When the SPI is enab led and not configured as a master, it will operate as an SPI slave. Another SPI device acting
as a master will initiate a transfer by driving the NSS sign al low. Th e master then shifts data o ut o f th e shift reg ister
on the MOSI pin using the its serial clock. The SPIF flag is set to logic 1 at the end of a data transfer (when the
NSS signal goes high). The slave can load its shift register for the next data transfer by writing to the SPI data
register. The slave must make the write to the data register at least one SPI serial clock cycle before the master
starts the next transmission. Otherwise, the byte of data already in the slav e’s shift register will be transferred.
Multiple masters may reside on the same bus. A Mode Fault flag (MODF, SPI0CN.5) is set to logic 1 when the SPI
is configured as a master (MSTEN = 1) and its slave select signal NSS is pulled low. When the Mode Fault flag is
set, the MSTEN and SPIEN bits of the SPI control register are cleared by hardware, thereby placing the SPI module
Receive Buffer
01234567
SPI SHIFT REGISTER
SLAVE DEVICE
MOSI
MISO
NSS
Receive Buffer
01234567
SPI SHIFT REGISTER
MASTER DEVICE
MOSI
MISO
NSS VDD
B au d Ra te
Generator SCK SCK
Px.y
Rev. 1.7 126
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
in an “off-line” state. In a multiple-master environment, the system controller should check the state of the
SLVSEL flag (SPI0CN.2) to ensure the bus is free b efore setting the MSTEN bit and in itiating a data transfer.
17.3. Serial Clock Timing
As shown in Figure 17.4, four combinations of serial clock phase and polarity can be selected using the clock
control bits in the SPI Configuration Register (SPI0CFG). The CKPHA bit (SPI0CFG.7) selects one of two clock
phases (edge used to latch the data). The CKPOL bit (SPI0CFG.6) selects between an active-high or active-low
clock. Both master and slave devices must be configured to use the same clock phase and polarity. Note: the SPI
should be disabled (by clearing the SPIEN bit, SPI0CN.0) while changing the clock phase and polarity.
The SPI Clock Rate Register (SPI0CKR) as shown in Figure 17.7 controls the master mode serial clock frequency.
This register is ignored when operating in slave mode.
Figure 17.4. Data/Clock Timing Diagram
SCK
(CKPOL = 0, CKPHA = 0)
SCK
(CKPOL =1, CKPHA = 0)
SCK
(CKPOL =1, CKPHA = 1)
SCK
(CKPOL = 0, CKPHA = 1)
MSB Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 LSB
MISO/MOSI
NSS
127 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
17.4. SPI Special Function Registers
The SPI is accessed and controlled through four special function registers in the system controller: SPI0CN Control
Register, SPI0DAT Data Register, SPI0CFG Configuration Register, and SPI0CKR Clock Rate Register. The four
special function registers related to the operation of the SPI Bus are described in the following section.
Figure 17.5. SPI0CFG: SPI Configuration Register
R/W R/W R R R R/W R/W R/W Reset Value
CKPHA CKPOL BC2 BC1 BC0 SPIFRS2 SPIFRS1 SPIFRS0 00000111
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0x9A
Bit7: CKPHA: SPI Clock Phase.
This bit controls the SPI clock phase.
0: Data sampled on first edge of SCK period.
1: Data sampled on second edge of SCK period.
Bit6: CKPOL: SPI Clo ck Polarity.
This bit controls the SPI clock polarity.
0: SCK line low in idle state.
1: SCK line high in idle state.
Bits5-3: BC2-BC0: SPI Bit Count.
Indicates which of the up to 8 bits of the SPI word have been transmitted.
BC2-BC0 Bit Transmitted
0 0 0 Bit 0 (LSB)
0 0 1 Bit 1
0 1 0 Bit 2
0 1 1 Bit 3
1 0 0 Bit 4
1 0 1 Bit 5
1 1 0 Bit 6
1 1 1 Bit 7 (MSB)
Bits2-0: SPIFRS2-SPIFRS0: SPI Frame Size.
These three bits determine the number of bits to shift in/out of the SPI shift register
during a data transfer in master mode. They are ignored in slave mode.
SPIFRS Bits Shifted
0 0 0 1
0 0 1 2
0 1 0 3
0 1 1 4
1 0 0 5
1 0 1 6
1 1 0 7
1 1 1 8
.
Rev. 1.7 128
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 17.6. SPI0CN: SPI Control Register
R/W R/W R/W R/W R R R/W R/W Reset Value
SPIF WCOL MODF RXOVRN TXBSY SLVSEL MSTEN SPIEN 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
(bit addressable) 0xF8
Bit7: SPIF: SPI Interrupt Flag.
This bit is set to logic 1 by hardware at the end of a data transfer. If interrup ts are en abled,
setting this bit causes the CPU to vector to the SPI0 interru pt service routine. This bit is
not automatically cleared by hardware. It must be cleared by software.
Bit6: WCOL: Write Collision Flag.
This bit is set to logic 1 by hardware (and generates a SPI interrupt) to indicate a write to
the SPI data register was attempted while a data transfer was in progress. It is cleared by
software.
Bit5: MODF: Mo de Fault Flag.
This bit is set to logic 1 by hardware (and generates a SPI interrupt) when a master mode
collision is detected (NSS is low and MSTEN = 1). This bit is not auto matically cleared by
hardware. It must be cleared by software.
Bit4: RXOVRN: Receive Overrun Flag.
This bit is set to logic 1 by hardware (and generates a SPI interrupt) when the receive
b
uffer still holds unread d ata from a previous transfer and the last bit of the current transfer
is shifted into the SPI shift register. This bit is not automatically cleared by hardware. It
must be cleared by software.
Bit3: TXBSY: Tran smit Busy Flag.
This bit is set to logic 1 by hardware wh ile a master mode transfer is in progr ess. It is
cleared by hardware at the end of the transfer.
Bit2: SLVSEL: Slave Selected Flag.
This bit is set to logic 1 when ever the NSS pin is low indicating it is enabled as a slave. It
is cleared to logic 0 when NSS is high (slave disabled).
Bit1: MSTEN: Master Mo de Enable.
0: Disable master mode. Operate in slave mode.
1: Enable master mode. Operate as a master.
Bit0: SPIEN: SPI Enable.
This bit enables/disables the SPI.
0: SPI disabled.
1: SPI enabled.
129 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 17.7. SPI0CKR: SPI Clock Rate Register
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
SCR7 SCR6 SCR5 SCR4 SCR3 SCR2 SCR1 SCR0 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0x9D
Figure 17.8. SPI0DAT: SPI Data Register
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0x9B
Bits7-0: SCR7-SCR0: SPI Clock Rate
These bits determine the frequency of the SCK output when the SPI module is
configured for master mode operation. The SCK clock frequency is a divided down
version of the system clock, and is given in the following equations:
f
SCK = 0.5 * fSYSCLK / (SPI0CKR + 1), for 0 SPI0CKR 255,
Bits7-0: SPI0DAT: SPI0 Transmit and Receive Data.
The SPI0DAT register is used to transmit and receive SPI data. Writing data to SPI0DAT
places the data immediately into the shift register and initiates a transfer when in Master
Mode. A read of SPI0DAT returns the conten
t
s of the receive buffer.
Rev. 1.7 130
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
18. UART
The UART is a serial port capable of asynchronous transmission. The UART can function in full duplex mode. In
all modes, receive data is buffered in a holding register. This allows the UART to start reception of a second
incoming data byte before software has finished reading the previous data byte.
The UART has an associated Serial Control Register (SCON) and a Serial Data Buffer (SBUF) in the SFRs. The
single SBUF location provides access to both transmit and receive registers. Reads access the Receive register and
writes access the Transmit register automatically.
The UART is capable of generating interrupts if enabled. The UART has two sources of interrupts: a Transmit
Interrupt flag, TI (SCON.1) set when transmission of a data byte is complete, and a Receive Interrupt flag, RI
(SCON.0) set when reception of a data byte is complete. The UART interrupt flags are not cleared by hardware
when the CPU vectors to the interrupt service routine. They must be cleared manually by software. This allows
software to determine the cause of the UART interrupt (transmit complete or receive complete).
Figure 18.1. UART Block Diagram
SBUF
Shift
Load SBUF
SFR Bus
Input Shift Register
(9 bits)
Bit Detector
Read
SBUF
Rx Control
Start
Rx Clock Load
SBUF
0x1FF Shift
Tx Control
Tx Clock
Serial
Port
Interrupt
Tx IRQ
Zero Detector
Send
Shift
SBUF
SFR Bus
SET
QD
CLR
Stop Bit
Gen.
TB8
Start
01
00
10
11
SMOD
1
0
01
00
10
11
Timer 2
Overflow
TCLK
1
0
RCLK
1
0
Timer 1
Overflow
SCON
S
M
2
T
B
8
R
B
8
T
IR
I
PCON
S
M
O
D
SMOD
Data
Write to
SBUF
S
M
1
S
M
0
R
E
N
Enable
REN
T2CON
R
C
L
K
T
C
L
K
SYSCLK
MSB
RB8
Rx IRQ
TI
RI
Crossbar
Baud Rate Generation Logic
Crossbar
RX
TX
Port I/O
1
0
32
64
12
SM0, SM1
{MODE}
16
16
2
131 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
18.1. UART Operational Modes
The UART provides four operating modes (one synchronous and three asynchronous) selected by setting
configuration bits in the SCON register. These four modes offer different baud rates and communication protocols.
The four modes are summarized in Table 18.1 below. Detailed descriptions follow.
Table 18.1. UART Modes
Mode Synchronization Baud Clock Data Bits Start/Stop Bits
0 Synchronous SYSCLK/12 8 None
1 Asynchronous Timer 1 or Timer 2 Overflow 8 1 Start, 1 Stop
2 Asynchronous SYSCLK/32 or SYSCLK/64 9 1 Start, 1 Stop
3 Asynchronous Timer 1 or Timer 2 Overflow 9 1 Start, 1 Stop
18.1.1. Mode 0: Synchronous Mode
Mode 0 provides synchronous, half-duplex communication. Serial data is transmitted and received on the RX pin.
The TX pin provides the shift clock for both transmit and receive. The MCU must be the master since it generates
the shift clock for transmission in both directions (see the interconnect diagram in Figure 18.2).
Eight data bits are transmitted/received, LSB first (see the timing diagram in Figure 18.3). Data transmission begins
when an in struction writes a data byte to the SBUF register. The TI Transmit Interrupt Flag (SCON.1) is set at th e
end of the eighth bit time. Data reception begins when the REN Receive Enable bit (SCON.4) is set to logic 1 and
the RI Receive Interrupt Flag (SCON.0) is cleared. One cycle after the eighth bit is shifted in, the RI flag is set and
reception stops until software clears the RI bit. An interrupt will occur if enabled when either TI or RI is set.
The Mode 0 baud rate is the system clock frequency divided by twelve. RX is forced to open-drain in mode 0, and
an external pull-up will typically be required.
Figure 18.2. UART Mode 0 Interconnect
Figure 18.3. UART Mode 0 Timing Diagram
18.1.2. Mode 1: 8-Bit UART, Variable Baud Rate
Shift
Reg.
CLK
C8051Fxxx
RX
TX
DATA
8 Extra Out
p
uts
D1D0 D2 D3 D4 D5 D6 D7
RX (data out) MODE 0 TRANSMIT
D0
MODE 0 RECEIVE
RX (data in)
D1 D2 D3 D4 D5 D6 D7
TX (clk out)
TX (clk out)
Rev. 1.7 132
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Mode 1 provides standard asynchronous, full duplex communication using a total of 10 bits per data byte: one start
bit, eight data bits (LSB first), and one sto p bit (see the timing diagram in Figure 18.4). Data are transmitted from
the TX pin and received at the RX pin (see the interconnection diagram in Figure 18.5). On receive, the eight data
bits are stored in SBUF and the stop bit goes into RB8 (SCON.2).
Data transmission begins when an instruction writes a data byte to the SBUF register. The TI Transmit Interrupt
Flag (SCON.1) is set at the end of the transmission (the beginning of the stop-bit time). Data reception can begin
any time after the REN Receive Enable bit (SCON.4) is set to logic 1. After the stop bit is received, the data byte
will be loaded into the SBUF receive register if the following conditions are met: RI must be logic 0, and if SM2 is
logic 1, the stop bit must be logic 1.
If these conditions are met, the eigh t bits of data are stor ed in SBUF, the stop bit is stored in RB8, and the RI flag is
set. If these conditions are n ot met, SBUF and RB8 will not be loaded and the RI flag will not be set. An interrup t
will occur if enabled when either TI or RI is set.
Figure 18.4. UART Mode 1 Timing Diagram
The baud rate generated in Mode 1 is a function of timer overflow. The UART can use Timer 1 operating in 8-bit
Counter/Timer with Auto-Reload Mode, or Timer 2 operating in Baud Rate Generator Mode to generate the baud
rate (note that the TX and RX clock sources are selected separately). On each timer overflow event (a rollover from
all ones (0xFF for Timer 1, 0xFFFF for Timer 2) to zero), a clock is sent to the baud rate logic.
When Timer 1 is selected as a baud rate source, the SMOD bit (PCON.7) selects whether or not to divide the
Timer 1 overflow rate by two. On reset, the SMOD bit is logic 0, thus selecting the lower speed baud rate by
default. The SMOD bit affects the baud rate generated by Timer 1 as follows:
Mode 1 Baud Rate = (1 / 32) * T1_OVERFLOWRATE (when the SMOD bit is set to logic 0).
Mode 1 Baud Rate = (1 / 16) * T1_OVERFLOWRATE (when the SMOD bit is set to logic 1).
When Timer 2 is selected as a baud rate source, the baud rate generated by Timer 2 is as follows:
Mode 1 Baud Rate = (1 / 16) * T2_OVERFLOWRATE.
The Timer 1 overflow rate is determined by the Timer 1 clock source (T1CLK) and reload value (TH1). The
frequency of T1CLK can be selected as SYSCLK, SYSCLK/12, or an external clock source. The Timer 1 overflow
rate can be calculated as follows: T1_OVERFLOWRATE = T1CLK / (256 – TH1).
For example, assume TMOD = 0x20.
If T1M (CKCON.4) is logic 1, then the above equation becomes:
T1_OVERFLOWRATE = (SYSCLK) / (256 – TH1).
If T1M (CKCON.4) is logic 0, then the above equation becomes:
T1_OVERFLOWRATE = (SYSCLK/12) / (256 – TH1).
D1D0 D2 D3 D4 D5 D6 D7
START
BIT
MARK STOP
BIT
BIT TIMES
BIT SAMPLING
SPACE
133 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
The Timer 2 overflow rate, when in Baud Rate Generator Mode and using an internal clock source, is determined
solely by the Timer 2 16-bit reload value (RCAP2H:RCAP2L). The Timer 2 clock source is fixed at SYSCLK/2.
The Timer 2 overflow rate can be calculated as follows:
T2_OVERFLOWRATE = (SYSCLK/2) / (65536 – [RCAP2H:RCAP2L]).
Timer 2 can be selected as the baud rate generator for RX and/or TX by setting RCLK (T2CON.5) and/or TCLK
(T2CON.4), respectively. Wh en either RCLK or TCLK is set to logic 1, Timer 2 interrup ts are au tomatically
disabled and the timer is forced into Baud Rate Generator Mode with SYSCLK/2 as its clock source. If a different
timebase is required, setting the C/T2 bit (T2CON.1 ) to logic 1 will allow Timer 2 to be clocked from the external
input pin T2. See the Timers section for complete timer configuration details.
Figure 18.5. UART Modes 1, 2, and 3 Interconnect Diagram
OR
RS-232
C8051Fxxx
RS-232
LEVEL
XLTR
TX
RX
C8051Fxxx
RX
TX
MCU
RX
TX
Rev. 1.7 134
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
18.1.3. Mode 2: 9-Bit UART, Fixed Baud Rate
Mode 2 provides asynchronous, full-duplex communication using a total of eleven bits per data byte: a start bit, 8
data bits (LSB first), a programmable ninth data bit, and a stop bit (see timing diagram in Figure 18.6). On transmit,
the ninth data bit is determined by the value in TB8 (SCON.3). It can be assigned the value of the parity flag P in
the PSW or used in multiprocessor communications. On receive, the ninth data bit goes into RB8 (SCON.2) and the
stop bit is ignored.
Data transmission begins when an instruction writes a data byte to the SBUF register. The TI Transmit Interrupt
Flag (SCON.1) is set at the end of the transmission (the beginning of the stop-bit time). Data reception can begin
any time after the REN Receive Enable bit (SCON.4) is set to logic 1. After the stop bit is received, the data byte
will be loaded into the SBUF receive register if the following conditions are met: RI must be logic 0, and if SM2 is
logic 1, the 9th bit must be logic 1.
If these conditions are met, the eigh t bits of d ata are stored in SBUF, the ninth bit is stored in RB8 and the RI flag is
set. If these conditions are n ot met, SBUF and RB8 will not be loaded and the RI flag will not be set. An interrup t
will occur if enabled when either TI or RI are set.
The baud rate in Mode 2 is a direct function of the system clock frequency as follows:
Mode 2 Baud Rate = 2SMOD * (SYSCLK / 64).
The SMOD bit (PCON.7) selects whether to divide SYSCLK by 32 or 64. In the formula, 2 is raised to the power
SMOD, resulting in a baud rate of either 1/32 or 1/64 of the system clock frequency. On reset, the SMOD bit is
logic 0, thus selecting the lower speed baud rate by default.
Figure 18.6. UART Modes 2 and 3 Timing Diagram
18.1.4. Mode 3: 9-Bit UART, Variable Baud Rate
Mode 3 is the same as Mode 2 in all respects except the baud rate is variable. The baud rate is determined in the
same manner as for Mode 1. Mode 3 operation transmits 11 bits: a start bit, 8 data bits (LSB first), a programmable
ninth data bit, and a stop bit. Timer 1 or Timer 2 overflows generate the baud rate just as with Mode 1. In
summary, Mode 3 transmits using the same protocol as Mode 2 but with Mode 1 baud rate generation.
D1D0 D2 D3 D4 D5 D6 D7
START
BIT
MARK STOP
BIT
BIT TIMES
BIT SAMPLING
SPACE D8
135 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
18.2. Multiprocessor Communications
Modes 2 and 3 support multiprocessor communication between a master processor and one or more slave processors
by special use of the ninth data bit. When a master processor wants to transmit to one or more slaves, it first sends
an address byte to select the target(s). An address byte differs from a data byte in that its ninth bit is logic 1; in a
data byte, the ninth bit is always set to logic 0.
Setting the SM2 bit (SCON.5) of a slave processor configures its UART such that when a stop bit is received, the
UART will generate an interrupt only if the ninth bit is logic one (RB8 = 1) signifying an address byte has been
received. In the UART’s interrupt handler, software will compare the received address with the slave’s own
assigned 8-bit address. If the addresses match, the slave will clear its SM2 bit to enable interrupts on the reception
of the following data byte(s). Slaves that weren’t addressed leave their SM2 bits set and do not generate interrupts
on the reception of the following data bytes, thereby ignoring the data. Once the entire message is received, the
addressed slave resets its SM2 bit to ignore all transmissions until it receives the next address byte.
Multiple addresses can be assigned to a single slave and/or a single address can be assigned to multiple slaves,
thereby enabling “broadcast” transmissions to more than one slave simultaneously. The master processor can be
configured to receive all transmissions or a protocol can be implemented such that the master/slave role is
temporarily reversed to enable half-duplex transmission between the original master and slave(s).
Figure 18.7. UART Multi-Processor Mode Interconnect Diagram
Master
Device Slave
Device
TXRX RX TX
Slave
Device
RX TX
Slave
Device
RX TX
VDD
Rev. 1.7 136
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Table 18.2. Oscillator Frequencies for Standard Baud Rates
Oscillator Frequency (MHz) Divide Factor Timer 1 Load Value* Resulting Baud Rate**
24.0 208 0xF3 115200 (115384)
23.592 205 0xF3 115200 (113423)
22.1184 192 0xF4 115200
18.432 160 0xF6 115200
16.5888 144 0xF7 115200
14.7456 128 0xF8 115200
12.9024 112 0xF9 115200
11.0592 96 0xFA 115200
9.216 80 0xFB 115200
7.3728 64 0xFC 115200
5.5296 48 0xFD 115200
3.6864 32 0xFE 115200
1.8432 16 0xFF 115200
24.576 320 0xEC 76800
25.0 434 0xE5 57600 (57870)
25.0 868 0xCA 28800
24.576 848 0xCB 28800 (28921)
24.0 833 0xCC 28800 (28846)
23.592 819 0xCD 28800 (28911)
22.1184 768 0xD0 28800
18.432 640 0xD8 28800
16.5888 576 0xDC 28800
14.7456 512 0xE0 28800
12.9024 448 0xE4 28800
11.0592 384 0xE8 28800
9.216 320 0xEC 28800
7.3728 256 0xF0 28800
5.5296 192 0xF4 28800
3.6864 128 0xF8 28800
1.8432 64 0xFC 28800
* Assumes SMOD=1 and T1M=1.
** Numbers in parenthesis show the actual baud rate.
Figure 18.8. SBUF: Serial (UART) Data Buffer Register
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0x99
Bits7-0: SBUF.[7:0]: Serial Data Buffer Bits 7-0 (MSB-LSB)
This is actually two registers; a transmit and a receive buffer register. When data is moved to
SBUF, it goes to the transmit buffer and is held for serial transmission. Moving a byte to
SBUF is what initiates the transmission. When data is moved from SBUF, it comes from the
receive buffer.
137 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 18.9. SCON: Serial Port Control Register
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
SM0 SM1 SM2 REN TB8 RB8 TI RI 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
(bit addressable) 0x98
Bits7-6: SM0-SM1: Serial Port Operation Mode.
These bits select the Serial Port Operation Mode.
SM0 SM1 Mode
0 0 Mode 0: Synchronous Mode
0 1 Mode 1: 8-Bit UART, Variable Baud Rate
1 0 Mode 2: 9-Bit UART, Fixed Baud Rate
1 1 Mode 3: 9-Bit UART, Variable Baud Rate
Bit5: SM2 : Multiprocessor Communication Enable.
The function of this bit is dependent on the Serial Port Operation Mode.
Mode 0: No effect
Mode 1: Checks for valid stop bit.
0: Logic level of stop bit is ignored.
1: RI will only be activated if sto p bit is logic level 1.
Mode 2 and 3: Multiprocessor Communications Enable.
0: Logic level of ninth bit is ignored.
1: RI is set and an interrupt is generated only when the ninth bit is logic 1.
Bit4: REN: Receive Enable.
This bit enables/disables the UART receiver.
0: UART reception disabled.
1: UART reception enabled.
Bit3: TB8: Ninth Transmission Bit.
The logic level of th is bit will be assigned to the ninth transmission bit in Modes 2 and 3. It
is not used in Modes 0 and 1. Set or cleared by software as required.
Bit2: RB8: Ninth Receive Bit.
The bit is assigned the logic level of the ninth bit received in Modes 2 and 3. In Mode 1, if
SM2 is logic 0, RB8 is assigned the logic level of the received stop bit. RB8 is not used in
Mode 0.
Bit1: TI: Transmit Interrupt Flag .
Set by hardware when a byte of data has b een transmitted by the UART (after the 8th bit in
Mode 0, or at the beginning of the stop bit in other modes). When the UART interrupt is
enabled, setting this bit causes the CPU to vector to the UART interrupt service routine.
This bit must be cleared manually by software
Bit0: RI: Receive Interrupt Flag.
Set by hardware when a byte of data has been received by the UART (after the 8th bit in
Mode 0, or after the stop bit in other modes – see SM2 bit for exception). When the
UART interrupt is enabled, settin g this bit causes the CPU to vecto r to the UART interrupt
service routine. This bit must be cleared manually by software.
Rev. 1.7 138
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
19. TIMERS
Each MCU implements four counter/timers: three are 16-bit counter/timers compatible with those found in the
standard 8051, and one is a 16-bit timer for use with the ADC, SMBus, or for general purpose use. These can be
used to measure time intervals, count external events and generate periodic interrupt requests. Timer 0 and Timer 1
are nearly identical and have four primary modes of operation. Timer 2 offers additional capabilities not available
in Timers 0 and 1. Timer 3 is similar to Timer 2, but without the capture or Baud Rate Generator modes.
Timer 0 and Timer 1: Timer 2: Timer 3:
13-bit counter/timer 16-bit counter/timer with auto-reload 16-bit timer with auto-reload
16-bit counter/timer 16-bit counter/timer with capture
8-bit counter/timer with auto-reload Baud rate generator
Two 8-bit counter/timers (Timer 0 only)
When functioning as a timer, the counter/timer registers are incremented on each clock tick. Clock ticks are derived
from the system clock divided by either one or twelve as specified by the Timer Clock Select bits (T2M-T0M) in
CKCON. The twelve-clocks-per-tick option provides compatibility with the older generation of the 8051 family.
Applications that require a faster timer can use the one-clock-per-tick option.
When functioning as a counter, a counter/timer register is incremented on each high-to-low transition at the selected
input pin for T0, T1, or T2. Events with a frequency of up to one-fourth the system clock’s frequency can be
counted. The input signal need not be periodic, but it should be held at a given level for at least two full system
clock cycles to ensure the level is sampled.
19.1. Timer 0 and Timer 1
Timer 0 and Timer 1 are accessed and controlled through SFRs. Each counter/timer is implemented as a 16-bit
register accessed as two separate bytes: a low byte (TL0 or TL1) and a high byte (TH0 or TH1). The
Counter/Timer Control (TCON) register is used to enable Timer 0 and Timer 1 as well as indicate their status. Both
counter/timers operate in one of four primary modes selected by setting the Mode Select bits M1-M0 in the
Counter/Timer Mode (TMOD) register. Each timer can be configured independently. Following is a detailed
description of each operating mode.
19.1.1. Mode 0: 13-bit Counter/Timer
Timer 0 and Timer 1 operate as a 13-bit counter/timer in Mode 0. The following describes the configuration and
operation of Timer 0. However, both timers operate identically and Timer 1 is configured in the same manner as
described for Timer 0.
The TH0 register holds the eight MSBs of the 13-bit counter/timer. TL0 holds the five LSBs in bit positions TL0.4-
TL0.0. The three upper bits of TL0 (TL0.7-TL0.5) are indeterminate and should be masked out or ignored when
reading. As the 13-bit timer register increments and overflows from 0x1FFF (all ones) to 0x0000, the timer
overflow flag TF0 (TCON.5) is set an d an interrupt will occur if enabled .
The C/T0 bit (TMOD.2) selects the counter/timer’s clock source. Clearing C/T selects the system clock as the input
for the timer. When C/T0 is set to logic 1, high-to-low transitions at the selected input pin increment the timer
register. (Refer to Port I/O Section 15.1 for information on selecting and configuring external I/O pins.)
139 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Setting the TR0 bit (TCON.4) enables the timer when either GATE0 (TMOD.3) is 0 or the input signal /INT0 is
logic-level one. Setting GATE0 to logic 1 allows the timer to be controlled by the external input signal /INT0,
facilitating pulse width measurements.
TR0 GATE0 /INT0 Counter/Timer
0 X X Disabled
1 0 X Enabled
1 1 0 Disabled
1 1 1 Enabled
X = Don’t Care
Setting TR0 does not reset the timer register. The timer register should be initialized to the desired value before
enabling the timer.
TL1 and TH1 form the 13-bit register for Timer 1 in the same manner as described above for TL0 and TH0. Timer
1 is configured and controlled using the relevant TCON and TMOD bits just as with Timer 0.
Figure 19.1. T0 Mode 0 Block Diagram
19.1.2. Mode 1: 16-bit Counter/Timer
Mode 1 operation is the same as Mode 0, except that the counter/timer registers use all 16 bits. The counter/timers
are enabled and configured in Mode 1 in the same manner as for Mode 0.
TL0
(5 bits) TH0
(8 bits)
GATE0
/INT0
TR0
T0
SYSCLK
12
0
1
1
0
TCLK
TCON
TF0
TR0
TR1
TF1
IE1
IT1
IE0
IT0
Interrupt
CKCON
T
2
M
T
1
M
T
0
M
TMOD
T
1
M
1
T
1
M
0
C
/
T
1
G
A
T
E
1
G
A
T
E
0
C
/
T
0
T
0
M
1
T
0
M
0
Crossbar
Crossbar
Rev. 1.7 140
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
19.1.3. Mode 2: 8-bit Counter/Timer with Auto-Reload
Mode 2 configures Timer 0 and Timer 1 to operate as 8-bit counter/timers with automatic reload of the start value.
The TL0 holds the count and TH0 holds the reload value. When the count in TL0 overflows from all ones to 0x00,
the timer overflow flag TF0 (TCON.5) is set and the counter in TL0 is reloaded from TH0. If enabled, an interrupt
will occur when the TF0 flag is set. The reload valu e in TH0 is not chang ed. TL0 must be initialized to the desired
value before enabling the timer for the first count to be correct. When in Mode 2, Timer 1 operates identically to
Timer 0. Both counter/timers are enabled and configured in Mode 2 in the same manner as Mode 0.
Figure 19.2. T0 Mode 2 Block Diagram
TCON
TF0
TR0
TR1
TF1
IE1
IT1
IE0
IT0
GATE0
/INT0
TR0
T0
SYSCLK
12
0
1
1
0
Interrupt
TCLK
TL0
(8 bits)
Reload
TH0
(8 bits)
CKCON
T
2
M
T
1
M
T
0
M
TMOD
T
1
M
1
T
1
M
0
C
/
T
1
G
A
T
E
1
G
A
T
E
0
C
/
T
0
T
0
M
1
T
0
M
0
Crossbar
Crossbar
141 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
19.1.4. Mode 3: Two 8-bit Counter/Timers (Timer 0 Only)
Timer 0 and Timer 1 behave differently in Mode 3. Timer 0 is configured as two separate 8-bit counter/timers held
in TL0 and TH0. The counter/timer in TL0 is controlled using the Timer 0 control/status bits in TCON and TMOD:
TR0, C/T0, GATE0 and TF0. It can use either the system clock or an external input signal as its timebase. The
TH0 register is restricted to a timer function sourced by the system clock. TH0 is enabled using the Timer 1 run
control bit TR1. TH0 sets the Timer 1 overflow flag TF1 on overflow and thus controls the Timer 1 interrupt.
Timer 1 is inactive in Mode 3, so with Timer 0 in Mod e 3, Timer 1 can be turned off and on by switching it into and
out of its Mode 3. When Timer 0 is in Mode 3, Timer 1 can be operated in Modes 0, 1 or 2, but cannot be clocked
by external signals nor set the TF1 flag and generate an interrupt. However, the Timer 1 overflow can be used for
baud rate generation. Refer to Section 18 (UART) for information on configuring Timer 1 for baud rate generation.
Figure 19.3. T0 Mode 3 Block Diagram
TL0
(8 bits)
TH0
(8 bits)
GATE0
/INT0
TR0
T0
SYSCLK C/T0
12
0
1
1
0
TMOD
T
1
M
1
T
1
M
0
C
/
T
1
G
A
T
E
1
G
A
T
E
0
C
/
T
0
T
0
M
1
T
0
M
0
TR1
TCON
TF0
TR0
TR1
TF1
IE1
IT1
IE0
IT0
Interrupt
Interrupt
CKCON
T
2
M
T
1
M
T
0
M
Crossbar
Crossbar
Rev. 1.7 142
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 19.4. TCON: Timer Control Register
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
TF1 TR1 TF0 TR0 IE1 IT1 IE0 IT0 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
(bit addressable) 0x88
Bit7: TF1: Timer 1 Overflow Flag.
Set by hardware when Timer 1 overflows. This flag can be cleared by software but is
automatically cleared when the CPU vectors to the Timer 1 interrupt service routine.
0: No Timer 1 overflow detected.
1: Timer 1 has overflowed.
Bit6: TR1: Timer 1 Run Control.
0: Timer 1 disabled.
1: Timer 1 enabled.
Bit5: TF0: Timer 0 Overflow Flag.
Set by hardware when Timer 0 overflows. This flag can be cleared by software but is
automatically cleared when the CPU vectors to the Timer 0 interrupt service routine.
0: No Timer 0 overflow detected.
1: Timer 0 has overflowed.
Bit4: TR0: Timer 0 Run Control.
0: Timer 0 disabled.
1: Timer 0 enabled.
Bit3: IE1: External Interrupt 1.
This flag is set by hardware when an edg e/lev el of type defined by IT1 is detected. It can
be cleared by software but is automatically cleared when the CPU vectors to the External
Interrupt 1 service routine if IT1 = 1. This flag is the inverse of the /INT1 input signal’s
logic level when IT1 = 0.
Bit2: IT1: Interrupt 1 Type Select.
This bit selects whether the con figured /INT1 signal will detect falling edge or activ e-low
level-sensitive interrupts.
0: /INT1 is level triggered.
1: /INT1 is edge triggered.
Bit1: IE0: External Interrupt 0.
This flag is set by hardware when an edg e/lev el of type defined by IT0 is detected. It can
be cleared by software but is automatically cleared when the CPU vectors to the External
Interrupt 0 service routine if IT0 = 1. This flag is the inverse of the /INT0 input signal’s
logic level when IT0 = 0.
Bit0: IT0: Interrupt 0 Type Select.
This bit selects whether the con figured /INT0 signal will detect falling edge or activ e-low
level-sensitive interrupts.
0: /INT0 is level triggered.
1: /INT0 is edge triggered.
143 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 19.5. TMOD: Timer Mode Register
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
GATE1 C/T1 T1M1 T1M0 GATE0 C/T0 T0M1 T0M0 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0x89
Bit7: GATE1: Timer 1 Gate Contro l.
0: Timer 1 enabled when TR1 = 1 irrespective of /INT1 logic level.
1: Timer 1 enabled only when TR1 = 1 AND /INT1 = logic level one.
Bit6: C/T1: Counter/Timer 1 Select.
0: Timer Function: Timer 1 incremented by clock defined by T1M bit (CKCON.4).
1: Counter Function: Timer 1 incremented by high-to-low transitions on external input pin
(T1).
Bits5-4: T1M1-T1M0: Timer 1 Mode Select.
These bits select the Timer 1 operation mode.
T1M1 T1M0 Mode
0 0 Mode 0: 13-bit counter/timer
0 1 Mode 1: 16-bit counter/timer
1 0 Mode 2: 8-bit counter/timer with auto-reload
1 1 Mode 3: Timer 1 Inactive/stopped
Bit3: GATE0: Timer 0 Gate Contro l.
0: Timer 0 enabled when TR0 = 1 irrespective of /INT0 logic level.
1: Timer 0 enabled only when TR0 = 1 AND /INT0 = logic level one.
Bit2: C/T0: Counter/Timer Select.
0: Timer Function: Timer 0 incremented by clock defined by T0M bit (CKCON.3).
1: Counter Function: Timer 0 incremented by high-to-low transitions on external input pin
(T0).
Bits1-0: T0M1-T0M0: Timer 0 Mode Select.
These bits select the Timer 0 operation mode.
T0M1 T0M0 Mode
0 0 Mode 0: 13-bit counter/timer
0 1 Mode 1: 16-bit counter/timer
1 0 Mode 2: 8-bit counter/timer with auto-reload
1 1 Mode 3: Two 8-bit counter/timers
Rev. 1.7 144
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 19.6. CKCON: Clock Control Register
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
- - T2M T1M T0M Reserved Reserved Reserved 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0x8E
Bits7-6: UNUSED. Read = 00b, W r ite = don’t care.
Bit5: T2M: Timer 2 Clock Select.
This bit controls the division of the system clock supplied to Timer 2. This bit is ignored
when the timer is in baud rate generator mode or counter mode (i.e. C/T2 = 1).
0: Timer 2 uses the system clock divided by 12.
1: Timer 2 uses the system clock.
Bit4: T1M: Timer 1 Clock Select.
This bit controls the division of the system clock supplied to Timer 1.
0: Timer 1 uses the system clock divided by 12.
1: Timer 1 uses the system clock.
Bit3: T0M: Timer 0 Clock Select.
This bit controls the division of the system clock supplied to Counter/Timer 0.
0: Counter/Timer uses the system clock divided by 12.
1: Counter/Timer uses the system clock.
Bits2-0: Reserved. Read = 000b, Must Write = 000.
145 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 19.7. TL0: Timer 0 Low Byte
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0x8A
Figure 19.8. TL1: Timer 1 Low Byte
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0x8B
Figure 19.9. TH0: Timer 0 High Byte
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0x8C
Figure 19.10. TH1: Timer 1 High Byte
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0x8D
Bits 7-0: TL0: Timer 0 Low Byte.
The TL0 register is the low byte of th e 16-bit Timer 0.
Bits 7-0: TH0: Timer 0 High Byte.
The TH0 register is the high byte of the 16-bit Timer 0.
Bits 7-0: TH1: Timer 1 High Byte.
The TH1 register is the high byte of the 16-bit Timer 1.
Bits 7-0: TL1: Timer 1 Low Byte.
The TL1 register is the low byte of th e 16-bit Timer 1.
Rev. 1.7 146
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
19.2. Timer 2
Timer 2 is a 16-bit counter/timer formed by the two 8-bit SFRs: TL2 (low byte) and TH2 (high byte). As with
Timers 0 and 1, Timer 2 can use either the system clock or transitions on an external input pin as its clock source.
The Counter/Timer Select bit C/T2 bit (T2CON.1) selects the clock source for Timer 2. Clearing C/T2 selects the
system clock as the input for the timer (divided by either one or twelve as specified by the Timer Clock Select bit
T2M in CKCON). When C/T2 is set to 1, high-to-low transitions at the T2 input pin increment the counter/timer
register. (Refer to Section 14 for information on selecting and configuring external I/O pins.) Timer 2 can also be
used to start an ADC Data Conversion.
Timer 2 offers capabilities not found in Timer 0 and Timer 1. It operates in one of three modes: 16-bit
Counter/Timer with Capture, 16-bit Counter/Timer with Auto-Reload or Baud Rate Generator Mode. Timer 2’s
operating mode is selected by setting configuration bits in the Timer 2 Control (T2CON) register. Below is a
summary of the Timer 2 operating modes and the T2CON bits used to configure the counter/timer. Detailed
descriptions of each mode follow.
RCLK TCLK CP/RL2 TR2 Mode
0 0 1 1 16-bit Counter/Timer with Capture
0 0 0 1 16-bit Counter/Timer with Auto-Reload
0 1 X 1 Baud Rate Generator for TX
1 0 X 1 Baud Rate Generator for RX
1 1 X 1 Baud Rate Generator for TX and RX
X X X 0 Off
147 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
19.2.1. Mode 0: 16-bit Counter/Timer with Capture
In this mode, Timer 2 operates as a 16-bit counter/timer with capture facility. A high-to-low transition on the T2EX
input pin causes the 16-bit value in Timer 2 (TH2, TL2) to be loaded into the capture registers (RCAP2H,
RCAP2L).
Timer 2 can use either SYSCLK, SYSCLK divided by 12, or high-to-low transitions on the external T2 pin as its
clock source when operating in Counter/Timer with Capture mode. Clearing the C/T2 bit (T2CON.1) selects the
system clock as the input for the timer (divided by one or twelve as specified by the Timer Clock Select bit T2M in
CKCON). When C/T2 is set to logic 1, a high-to-low transition at the T2 input pin increments the counter/timer
register. As the 16-bit counter/timer register increments and overflows from 0xFFFF to 0x0000, the TF2 timer
overflow flag (T2CON.7) is set and an interrupt will occur if the interrupt is enabled.
Counter/Timer with Capture mode is selected by setting the Capture/Reload Select bit CP/RL2 (T2CON.0) and the
Timer 2 Run Control bit TR2 (T2CON.2) to logic 1. The Timer 2 External Enable EXEN2 (T2CON.3) must also be
set to logic 1 to enable a capture. If EXEN2 is cleared, transitions on T2EX will be ignored.
Figure 19.11. T2 Mode 0 Block Diagram
TL2 TH2
EXEN2
T2EX
TR2
T2
SYSCLK
12
0
1
1
0
Interrupt
TCLK
RCAP2L RCAP2H
Capture
T2CON
RCLK
TCLK
EXF2
EXEN2
TR2
C/T2
CP/RL2
TF2
CKCON
T
2
M
T
1
M
T
0
M
Crossbar
Crossbar
Rev. 1.7 148
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
19.2.2. Mode 1: 16-bit Counter/Timer with Auto-Reload
The Counter/Timer with Auto-Reload mode sets the TF2 timer overflow flag when the counter/timer register
overflows from 0xFFFF to 0x0000. An interrupt is generated if enabled. On overflow, the 16-bit value held in the
two capture registers (RCAP2H, RCAP2L) is automatically loaded into the counter/timer register and the timer is
restarted.
Counter/Timer with Auto-Reload mode is selected by clearing the CP/RL2 bit. Setting TR2 to logic 1 enables and
starts the timer. Timer 2 can use either the system clock or transitions on an external input pin as its clock source, as
specified by the C/T2 bit. If EXEN2 is set to logic 1, a high-to-low transition o n T2EX will also cause Timer 2 to
be reloaded. If EXEN2 is cleared, transitions on T2EX will be ignored.
Figure 19.12. T2 Mode 1 Block Diagram
TL2 TH2
TR2
T2
SYSCLK
12
0
1
1
0
TCLK
RCAP2L RCAP2H
Reload
CKCON
T
2
M
T
1
M
T
0
M
Interrupt
T2CON
RCLK
TCLK
EXF2
EXEN2
TR2
C/T2
CP/RL2
TF2
Crossbar
EXEN2
Crossbar
T2EX
149 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
19.2.3. Mode 2: Baud Rate Generator
Timer 2 can be used as a baud rate generator for the serial port (UART) when the UART is operated in modes 1 or 3
(refer to Section 18.1 for more information on UART operational modes). In Baud Rate Generator mode, Timer 2
works similarly to the auto-reload mode. On overflo w, the 16-b it value held in the two capture registers (RCAP2H,
RCAP2L) is automatically loaded into the counter/timer register. However, the TF2 overflow flag is not set and no
interrupt is generated. Instead, the overflow event is used as the input to the UART’s shift clock. Timer 2
overflows can be used to generate baud rates for transmit and/or receive independently.
The Baud Rate Generator mode is selected by setting RCLK (T2CON.5) and/or TCLK (T2CON.4) to logic one.
When RCLK or TCLK is set to logic 1, Timer 2 operates in the auto-reload mode regardless of the state of the
CP/RL2 bit. The baud rate for the UART, when operating in mode 1 or 3, is determined by the Timer 2 overflow
rate:
Baud Rate = Timer 2 Overflow Rate / 16.
Note, in all other modes, the timebase for the timer is the system clock divided by one or twelve as selected by the
T2M bit in CKCON. However, in Baud Rate Generator mode, the timebase is the system clock divided by two. No
other divisor selection is possible. If a different time base is required, setting the C/T2 bit to logic 1 will allow the
timebase to be derived from the external input pin T2. In this case, the baud rate for the UART is calculated as:
Baud Rate = FCLK / [32 * (65536 – [RCAP2H:RCAP2L]) ]
Where FCLK is the frequency of the signal supplied to T2 and [RCAP2H:RCAP2L] is the 1 6-bit value held in the
capture registers.
As explained above, in Baud Rate Generator mode, Timer 2 does not set the TF2 overflow flag and therefore cannot
generate an interrupt. However, if EXEN2 is set to logic 1, a high-to-low transition on the T2EX input pin will set
the EXF2 flag and a Timer 2 interrupt will occur if enabled. Therefore, the T2EX input may be used as an
additional external in terrupt source.
Figure 19.13. T2 Mode 2 Block Diagram
TL2 TH2
EXEN2
T2EX
TR2
T2
SYSCLK C/T2
2
1
0
Interrupt
TCLK
RCAP2L RCAP2H
Reload
2
16
16
Timer 1
Overflow
RX Clock
TX Clock
TCLK
RCLK
T2CON
RCLK
TCLK
EXF2
EXEN2
TR2
C/T2
CP/RL2
TF2
Crossbar
Crossbar
PCON
S
M
O
D
G
F
1
G
F
0
S
T
O
P
I
D
L
E
1
0
1
0
1
0
Timer 2
Overflow
Rev. 1.7 150
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 19.14. T2CON: Timer 2 Control Register
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
TF2 EXF2 RCLK TCLK EXEN2 TR2 C/T2 CP/RL2 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
(bit addressable) 0xC8
Bit7: TF2: Timer 2 Overflow Flag.
Set by hardware when Timer 2 overflows from 0xFFFF to 0x0000 or reload value. When
the Timer 2 interrupt is enabled, setting this bit causes the CPU to vector to the Timer 2
interrupt service routine. This bit is not automatically cleared by hardware and must be
cleared by software. TF2 will not be set when RCLK and/or TCLK are logic 1.
Bit6: EXF2: Timer 2 External Flag.
Set by hardware when either a capture or reload is caused by a high-to-low transition on
the T2EX input pin and EXEN2 is logic 1. When the Timer 2 interrupt is enabled, setting
this bit causes the CPU to vector to the Timer 2 Interrupt service routine. Th is bit is not
automatically cleared by hardware and must be cleared by software.
Bit5: RCLK: Receive Clock Flag.
Selects which timer is used for the UART’s receive clock in modes 1 or 3.
0: Timer 1 overflows used for receive clock.
1: Timer 2 overflows used for receive clock.
Bit4: TCLK: Tran smit Clock Flag .
Selects which timer is used for the UART’s transmit clock in modes 1 or 3.
0: Timer 1 overflows used for transmit clock.
1: Timer 2 overflows used for transmit clock.
Bit3: EXEN2: Timer 2 External Enable.
Enables high-to-low transitions on T2EX to trigger captures or reloads when Timer 2 is not
operating in Baud Rate Generator mode.
0: High-to-low transitions on T2EX ignored.
1: High-to-low transitions on T2EX cause a capture or reload.
Bit2: TR2: Timer 2 Run Control.
This bit enables/disables Timer 2.
0: Timer 2 disabled.
1: Timer 2 enabled.
Bit1: C/T2: Counter/Timer Select.
0: Timer Function: Timer 2 incremented by clock defined by T2M (CKCON.5).
1: Counter Function: Timer 2 incremented by high-to-low transitions on external input pin
(T2).
Bit0: CP/RL2 : Capture/Reload Select.
This bit selects whether Timer 2 functions in capture or auto-reload mode. EXEN2 must
be logic 1 for high-to-low transitions on T2EX to be recognized and used to trigger
captures or reloads. If RCLK or TCLK is set, this bit is ignored and Timer 2 will function
in auto-reload mode.
0: Auto-reload on Timer 2 overflow or high-to-low transition at T2EX (EXEN2 = 1).
1: Capture on high-to-low transition at T2EX (EXEN2 = 1).
151 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 19.15. RCAP2L: Timer 2 Capture Register Low Byte
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xCA
Figure 19.16. RCAP2H: Timer 2 Capture Register High Byte
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xCB
Figure 19.17. TL2: Timer 2 Low Byte
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xCC
Figure 19.18. TH2: Timer 2 High Byte
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xCD
Bits 7-0: RCAP2H: Timer 2 Capture Register High Byte.
The RCAP2H register captures the high byte of Timer 2 when Timer 2 is configured in
capture mode. When Timer 2 is configured in auto-reload mode, it holds the high byte of
the reload value.
Bits 7-0: RCAP2L: Timer 2 Capture Register Low Byte.
The RCAP2L register captures the low byte of Timer 2 when Timer 2 is configured in
capture mode. When Timer 2 is configured in auto-reload mode, it holds the low byte of
the reload value.
Bits 7-0: TH2: Timer 2 High Byte.
The TH2 register contains the high byte of the 16-bit Timer 2.
Bits 7-0: TL2: Timer 2 Low Byte.
The TL2 register contains the low byte of the 16-bit Timer 2.
Rev. 1.7 152
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
19.3. Timer 3
Timer 3 is a 16-bit timer formed by the two 8-bit SFRs, TMR3L (low byte) and TMR3H (high byte). The input for
Timer 3 is the system clock (divided by either one or twelve as specified by the Timer 3 Clock Select bit T3M in the
Timer 3 Control Register TMR3CN). Timer 3 is always configured as an auto-reload timer, with the reload value
held in the TMR3RLL (low byte) and TMR3RLH (high byte) registers. Timer 3 can be used to start an ADC Data
Conversion, for SMBus timing (see Section 16.5), or as a general-purpose timer. Timer 3 does not have a counter
mode.
Figure 19.19. Timer 3 Block Diagram
Figure 19.20. TMR3CN: Timer 3 Control Register
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
TF3 - - - - TR3 T3M - 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0x91
Bit7: TF3: Timer3 Overflow Flag.
Set by hardware when Timer 3 overflows from 0xFFFF to 0x0000. When the Timer 3
interrupt is enabled, settin g this bit causes the CPU to vecto r to the Timer 3 Interrupt
service routine. This bit is n ot automatically cleared by hardware and must be cleared by
software.
Bits6-3: UNUSED. Read = 0000b, W r ite = don’t care.
Bit2: TR3: Timer 3 Run Control.
This bit enables/disables Timer 3.
0: Timer 3 disabled.
1: Timer 3 enabled.
Bit1: T3M: Timer 3 Clock Select.
This bit controls the division of the system clock supplied to Counter/Timer 3.
0: Counter/Timer 3 uses the system clock divided by 12.
1: Counter/Timer 3 uses the system clock.
Bit0: UNUSED. Read = 0, Write = don’t care.
TMR3L TMR3H
TR3
SYSCLK
12
0
1TCLK
TMR3RLL TMR3RLH
Reload
Interrupt
TMR3CN
TR3
T3M
TF3
T3M
TOE
SCL
(from SMBus)
(to ADC)
Crossbar
153 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 19.21. TMR3RLL: Timer 3 Reload Register Low Byte
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0x92
Figure 19.22. TMR3RLH: Timer 3 Reload Register High Byte
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0x93
Figure 19.23. TMR3L: Timer 3 Low Byte
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0x94
Figure 19.24. TMR3H: Timer 3 High Byte
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0x95
Bits 7-0: TMR3RLH: Timer 3 Reload Register High Byte.
Timer 3 is configured as an auto-reload timer. This register holds the high byte of the
reload value.
Bits 7-0: TMR3RLL: Timer 3 Reload Register Low Byte.
Timer 3 is configured as an auto-reload timer. This register holds the low byte of the
reload value.
Bits 7-0: TMR3H: Timer 3 High Byte.
The TMR3H register is the high byte of Timer 3.
Bits 7-0: TMR3L: Timer 3 Low Byte.
The TMR3L register is the low byte of Timer 3.
Rev. 1.7 154
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
20. PROGRAMMABLE COUNTER ARRAY
The Programmable Counter Array (PCA) provides enhanced timer functionality while requiring less CPU
intervention than the standard 8051 counter/timers. The PCA consists of a dedicated 16-bit counter/timer and five
16-bit capture/compare modules. Each capture/compare module has its own associated I/O line (CEXn) which is
routed through the Crossbar to Port I/O when enabled (see Section 15.1 for details on configuring the Crossbar).
The counter/timer is driven by a configurable timebase that can select between four inputs as its source: system
clock divided by twelve, system clock divided by four, Timer 0 overflow, or an external clock signal on the ECI
line. The PCA is configured and controlled through the system controller’s Special Function Registers. The basic
PCA block diagram is shown in Figure 20.1.
Figure 20.1. PCA Block Diagram
16-Bit Counter/Timer
Capture/Compare
Module 1
Capture/Compare
Module 0 Capture/Compare
Module 2 Capture/Compare
Module 3 Capture/Compare
Module 4
CEX1
System
Clock /4
T0 Overflow
ECI
Crossbar
CEX2
CEX3
CEX4
CEX0
Port I/O
/12 00
01
10
CPS=11
155 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
20.1. Capture/Compare Modules
Each module can be configured to operate independently in one of four operation modes: Edge-triggered Capture,
Software Timer, High Speed Output, or Pulse Width Modulator. Each module has Special Function Registers
(SFRs) associated with it in the CIP-51 system controller. These registers are used to exchange data with a module
and configure the module’s mode of operation.
Table 20.1 summarizes the bit settings in the PCA0CPMn registers used to place the PCA capture/compare modules
into different operating modes. Setting the ECCFn bit in a PCA0CPMn register enables the module’s CCFn
interrupt. Note: PCA0 interrupts must be globally enabled before individual CCFn interrupts are recognized. PCA0
interrupts are globally enabled by setting the EA bit (IE.7) and the EPCA0 bit (EIE1.3) to logic 1. See Figure 20.2
for details on the PCA interrupt configuration.
Table 20.1. PCA0CPM Register Settings for PCA Capture/Compare Modules
ECOM CAPP CAPN MAT TOG PWM ECCF Operation Mode
X 1 0 0 0 0 X Capture triggered b y positive edge on
CEXn
X 0 1 0 0 0 X Capture triggered by negative edge on
CEXn
X 1 1 0 0 0 X Capture triggered by transition on CEXn
1 0 0 1 0 0 X Software Timer
1 0 0 1 1 0 X High Speed Output
1 0 0 X 0 1 X Pulse Width Modulator
X = Don’t Care
Figure 20.2. PCA Interrupt Block Diagram
PCA0CN
C
FC
RC
C
F
0
C
C
F
2
C
C
F
1
C
C
F
4
C
C
F
3
PCA0MD
C
I
D
L
E
C
F
C
P
S
1
C
P
S
0
0
1
PCA Module 0
PCA Module 1
ECCF1
0
1
ECCF0
0
1
PCA Module 2
ECCF2
0
1
PCA Module 3
ECCF3
0
1
PCA Module 4
ECCF4
PCA Counter/
Timer Overflow
0
1
Interrupt
Priority
Decoder
EPCA0
(EIE1.3)
0
1
EA
(IE.7)
0
1
PCA0CPMn
E
C
O
M
n
E
C
C
F
n
T
O
G
n
P
W
M
n
C
A
P
P
n
C
A
P
N
n
M
A
T
n
(for n = 0 to 4)
Rev. 1.7 156
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
20.1.1. Edge-triggered Capture Mode
In this mode, a valid transition on the CEXn pin causes the PCA to capture the value of the PCA counter/timer and
load it into the corresponding module’s 16-bit capture/compare register (PCA0CPLn and PCA0CPHn). The CAPPn
and CAPNn bits in the PCA0CPMn register are used to select th e type o f tran sition that trig gers th e captu re: lo w-to-
high transition (positive edge), high-to-low transition (negative edge), or either transition (positive or negative
edge). When a capture occurs, the Capture/Compare Flag (CCFn) in PCA0CN is set to logic 1 and an interrupt
request is generated if CCF interru pts are enabled . The CCFn b it is not automatically cleared by hardware when the
CPU vectors to the interrupt service routine, and must be cleared by software.
Figure 20.3. PCA Capture Mode Diagram
PCA0L
PCA0CPLn
PCA
Timebase
CEXn
CrossbarPort I/O
PCA0H
Capture
PCA0CPHn
PCA0CN
C
FC
RC
C
F
0
C
C
F
2
C
C
F
1
C
C
F
4
C
C
F
3
0
PCA0CPMn
E
C
O
M
n
E
C
C
F
n
T
O
G
n
P
W
M
n
C
A
P
P
n
C
A
P
N
n
M
A
T
n
0000
1
0
1
(to CCFn)
PCA Interrupt
157 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
20.1.2. Software Timer (Compare) Mode
In Software Timer mode, the PCA counter/timer is compared to the module’s 16-bit capture/compare register
(PCA0CPHn and PCA0CPLn). When a match occurs, the Capture/Compare Flag (CCFn) in PCA0CN is set to
logic 1 and an interrupt request is generated if CCF interrupts are enabled. The CCFn bit is not automatically
cleared by hardware when the CPU vectors to the interrupt service routine, and must be cleared by software.
Setting the ECOMn and MATn b its in the PCA0CPMn register enables Software Timer mode.
Figure 20.4. PCA Software Timer Mode Diagram
20.1.3. High Speed Output Mode
In this mode, each time a match occurs between the PCA Timer Counter and a module’s 16-bit capture/compare
register (PCA0CPHn and PCA0CPLn) the logic level on the module’s associated CEXn pin will toggle. Setting the
TOGn, MATn, and ECOMn bits in the PCA0CPMn register enables the High-Speed Output mode.
Figure 20.5. PCA High Speed Output Mode Diagram
Match
16-bit Comparator
PCA0H
PCA0CPHn
Enable
PCA0L
PCA
Timebase
PCA0CPLn
PCA0CPMn
E
C
O
M
n
E
C
C
F
n
T
O
G
n
P
W
M
n
C
A
P
P
n
C
A
P
N
n
M
A
T
n
00 00
PCA0CN
C
FC
RC
C
F
0
C
C
F
2
C
C
F
1
C
C
F
4
C
C
F
3
PCA Interrupt
0
1
x
ENB
ENB
0
1
Write to
PCA0CPLn
Write to
PCA0CPHn
Reset
Match
16-bit Comparator
PCA0H
PCA0CPHn
Enable
PCA0L
PCA
Timebase
PCA0CPLn
PCA0CN
C
FC
RC
C
F
0
C
C
F
2
C
C
F
1
C
C
F
4
C
C
F
3
PCA Interrupt
0
1
PCA0CPMn
E
C
O
M
n
E
C
C
F
n
T
O
G
n
P
W
M
n
C
A
P
P
n
C
A
P
N
n
M
A
T
n
00 0x
CEXn
Crossbar Port I/O
Toggle
ENB
ENB
0
1
Write to
PCA0CPLn
Write to
PCA0CPHn
Reset
0
1
TOGn
Rev. 1.7 158
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
20.1.4. Pulse Width Modulator Mode
All of the modules can be used independently to generate pulse width modulated (PWM) outputs on their respective
CEXn pin. The frequency of the output is dependent on the timebase for the PCA counter/timer. The duty cycle of
the PWM output signal is varied using the module’s PCA0CPLn capture/compare register. When the value in the
low byte of the PCA counter/timer (PCA0L) is equal to the value in PCA0CPLn, the output on the CEXn pin will
be set. When the count value in PCA0L overflows, the CEXn output will be reset (see Figure 20.6). Also, when
the counter/timer low byte (PCA0L) overflows from 0xFF to 0x00, PCA0CPLn is reloaded automatically with the
value stored in the PCA0CPHn without software intervention. It is good practice to write to PCA0CPHn instead of
PCA0CPLn to avoid glitches in the digital comparator. Setting the ECOMn and PWMn bits in the PCA0CPMn
register enables Pulse Width Modulator mode.
Figure 20.6. PCA PWM Mode Diagram
8-bit
Comparator
PCA0L
PCA0CPLn
PCA0CPHn
CEXn
Enable
Overflow
PCA Timebase
00x0 x
Q
Q
SET
CLR
S
R
match
PCA0CPMn
E
C
O
M
n
E
C
C
F
n
T
O
G
n
P
W
M
n
C
A
P
P
n
C
A
P
N
n
M
A
T
n
ENB
ENB
0
1
Write to
PCA0CPLn
Write to
PCA0CPHn
Reset
Crossbar P o rt I/O
159 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
20.2. PCA Counter/Timer
The 16-bit PCA counter/timer consists of two 8-bit SFRs: PCA0L and PCA0H. PCA0H is the high byte (MSB) of
the 16-bit counter/timer and PCA0L is the low byte (LSB). Reading PCA0L automatically latches the value of
PCA0H at the same time. By reading the PCA0L Register first, this allows the PCA0H v alue to be h eld (at the time
PCA0L was read) until the user reads the PCA0H Register. Reading PCA0H or PCA0L does not disturb the
counter operation. The CPS1 and CPS0 bits in the PCA0MD register select the timebase for the counter/timer as
shown in Table 20.2.
When the counter/timer overflows from 0xFFFF to 0x0000, the Counter Overflow Flag (CF) in PCA0MD is set to
logic 1 and an interrupt request is generated if CF interrupts are enabled. Setting the ECF bit in PCA0MD to logic 1
enables the CF flag to gen erate an interrupt request. The CF bit is not automatically cleared by hardware when the
CPU vectors to the interrupt service routine, and must be cleared by software. (Note: PCA0 interrupts must be
globally enabled before CF interrupts are recognized. PCA0 interrupts are globally enabled by setting the EA bit
(IE.7) and the EPCA0 bit in EIE1 to logic 1.) Clearing the CIDL bit in the PCA0MD register allows the PCA to
continue normal operation while the microcontroller core is in Idle mode.
Table 20.2. PCA Timebase Input Options
CPS1 CPS0 Timebase
0 0 System clock divided by 12
0 1 System clock divided by 4
1 0 Timer 0 overflow
1 1 High-to-low transitions on ECI (max rate = system clock divided by 4)
Figure 20.7. PCA Counter/Timer Block Diagram
PCA0H PCA0L
PCA0CN
C
FC
RC
C
F
0
C
C
F
2
C
C
F
1
C
C
F
4
C
C
F
3
SYSCLK/12
SYSCLK/4
Timer 0 Overflow
ECI
00
01
10
11
PCA0MD
C
I
D
L
E
C
F
C
P
S
1
C
P
S
0
Snapshot
Register
To SFR Bus
Overflow To PCA Interrupt System
IDLE
0
1
CF
PCA0L
read or
write
To PCA Modules
Rev. 1.7 160
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
20.3. Register Descriptions for PCA
The system device may implement one or more Programmable Counter Arrays. Following are detailed descriptions
of the special function registers related to the operation of the PCA. The CIP-51 System Controller section of the
datasheet provides additional information on the SFRs and their use.
Figure 20.8. PCA0CN: PCA Control Register
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
CF CR - CCF4 CCF3 CCF2 CCF1 CCF0 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
(bit addressable) 0xD8
Bit7: CF: PCA Counter/Timer Overflow Flag.
Set by hardware when the PCA Counter/Timer overflows from 0xFFFF to 0x0000. When
the Counter/Timer Overflow (CF) interrupt is enabled, setting this bit causes the CPU to
vector to the CF interrupt service routine. This bit is not automatically cleared by
hardware and must be cleared by software.
Bit6: CR: PCA Counter/Timer Run Control.
This bit enables/disables the PCA Counter/Timer.
0: PCA Counter/Timer disabled.
1: PCA Counter/Timer enabled.
Bit5: UNUSED. Read = 0, Write = don’t care.
Bit4: CCF4: PCA Module 4 Capture/Compare Flag.
This bit is set by hardware when a match or capture o ccurs. When the CCF interrupt is
enabled, setting this bit causes the CPU to vector to the CCF interrupt service routine. This
bit is not automatically cleared by hardware and must be cleared by software.
Bit3: CCF3: PCA Module 3 Capture/Compare Flag.
This bit is set by hardware when a match or capture o ccurs. When the CCF interrupt is
enabled, setting this bit causes the CPU to vector to the CCF interrupt service routine. This
bit is not automatically cleared by hardware and must be cleared by software.
Bit2: CCF2: PCA Module 2 Capture/Compare Flag.
This bit is set by hardware when a match or capture o ccurs. When the CCF interrupt is
enabled, setting this bit causes the CPU to vector to the CCF interrupt service routine. This
bit is not automatically cleared by hardware and must be cleared by software.
Bit1: CCF1: PCA Module 1 Capture/Compare Flag.
This bit is set by hardware when a match or capture o ccurs. When the CCF interrupt is
enabled, setting this bit causes the CPU to vector to the CCF interrupt service routine. This
bit is not automatically cleared by hardware and must be cleared by software.
Bit0: CCF0: PCA Module 0 Capture/Compare Flag.
This bit is set by hardware when a match or capture o ccurs. When the CCF interrupt is
enabled, setting this bit causes the CPU to vector to the CCF interrupt service routine. This
bit is not automatically cleared by hardware and must be cleared by software.
161 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 20.9. PCA0MD: PCA Mode Register
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
CIDL - - - - CPS1 CPS0 ECF 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xD9
Bit7: CIDL: PCA Counter/Timer Idle Control.
Specifies PCA behavior when CPU is in Idle Mode.
0: PCA continues to function normally while the system controller is in Idle Mode.
1: PCA operation is suspended while the system controller is in Idle Mode.
Bits6-3: UNUSED. Read = 0000b, W r ite = don’t care.
Bits2-1: CPS1-CPS0: PCA Counter/Timer Pulse Select.
These bits select the timebase source for the PCA counter.
CPS1 CPS0 Timebase
0 0 System clock divided by 12
0 1 System clock divided by 4
1 0 Timer 0 overflow
1 1 High-to-low transitions on ECI (max rate = system clock divided by 4)
Bit0: ECF: PCA Counter/Timer Overflow Interrupt Enable.
This bit sets the masking of the PCA Counter/Timer Overflow (CF) interrupt.
0: Disable the CF interrupt.
1: Enable a PCA Counter/Timer Overflow interrupt request when CF (PCA0CN.7) is set.
Rev. 1.7 162
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 20.10. PCA0CPMn: PCA Capture/Compare Registers
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
- ECOMn CAPPn CAPNn MATn TOGn PWMn ECCFn 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xDA-0xDE
PCA0CPMn Address: PCA0CPM0 = 0xDA (n = 0)
PCA0CPM1 = 0xDB (n = 1)
PCA0CPM2 = 0xDC (n = 2)
PCA0CPM3 = 0xDD (n = 3)
PCA0CPM4 = 0xDE (n = 4)
Bit7: UNUSED. Read = 0, Write = don’t care.
Bit6: ECOMn: Comparator Function Enable.
This bit enables/disables the comparator function for PCA module n.
0: Disabled.
1: Enabled.
Bit5: CAPPn : Capture Positive Functio n Enable.
This bit enables/disables the positive edge capture for PCA module n.
0: Disabled.
1: Enabled.
Bit4: CAPNn: Capture Negative Function Enable.
This bit enables/disables the negative edge capture for PCA module n.
0: Disabled.
1: Enabled.
Bit3: MATn : Match Function Enab le.
This bit enables/disables the match function for PCA module n. When enabled, matches o
f
the PCA counter with a module’s capture/compare register cause the CCFn bit in
PCA0MD register to be set.
0: Disabled.
1: Enabled.
Bit2: TOGn: Toggle Function Enable.
This bit enables/disables the toggle function for PCA module n. When enabled, matches
of the PCA counter with a module’s capture/compare register cause the logic level on the
CEXn pin to toggle.
0: Disabled.
1: Enabled.
Bit1: PWMn: Pulse Width Modulation Mode Enable.
This bit enables/disables the comparator function for PCA module n. When enabled, a
pulse width modulated signal is output on the CEXn pin.
0: Disabled.
1: Enabled.
Bit0: ECCFn: Capture/Compare Flag Interrupt Enable.
This bit sets the masking of the Captu re/Compare Flag (CCFn) interrupt.
0: Disable CCFn interrupts.
1: Enable a Capture/Compare Flag interrupt request when CCFn is set.
163 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 20.11. PCA0L: PCA Counter/Timer Low Byte
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xE9
Figure 20.12. PCA0H: PCA Counter/Timer High Byte
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xF9
Figure 20.13. PCA0CPLn: PCA Capture Module Low Byte
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xEA-0xEE
Figure 20.14. PCA0CPHn: PCA Capture Module High Byte
R/W R/W R/W R/W R/W R/W R/W R/W Reset Value
00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
SFR Address:
0xFA-0xFE
Bits 7-0: PCA0L: PCA Counter/Timer Low Byte.
The PCA0L register holds the low byte (LSB) of the 16-bit PCA Counter/Timer.
Bits 7-0: PCA0H: PCA Counter/Timer High Byte.
The PCA0H register holds the high byte (MSB) of the 16-bit PCA Counter/Timer. Note
the value read is actually from the snapsho t reg ister in order to synchron ize it with PCA0L.
PCA0CPHn Address: PCA0CPH0 = 0xFA (n = 0)
PCA0CPH1 = 0xFB (n = 1)
PCA0CPH2 = 0xFC (n = 2)
PCA0CPH3 = 0xFD (n = 3)
PCA0CPH4 = 0xFE (n = 4)
Bits7-0: PCA0CPHn: PCA Capture Module High Byte.
The PCA0CPHn register holds the high byte (MSB) of the 16
-
bit capture module n.
PCA0CPLn Address: PCA0CPL0 = 0xEA (n = 0)
PCA0CPL1 = 0xEB (n = 1)
PCA0CPL2 = 0xEC (n = 2)
PCA0CPL3 = 0xED (n = 3)
PCA0CPL4 = 0xEE (n = 4)
Bits7-6: PCA0CPLn: PCA Capture Module Low Byte.
The PCA0CPLn register holds the low byte (LSB) of the 16-bit capture module n.
Rev. 1.7 164
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
21. JTAG (IEEE 1149.1)
Each MCU has an on-chip JTAG interface and logic to support boundary scan for production and in-system testing,
Flash read and write operations, and non-intrusive in-circuit debug. The JTAG interface is fully compliant with the
IEEE 1149.1 specification. Refer to this specification for detailed descriptions of the Test Interface and Boundary-
Scan Architecture. Access of the JTAG Instruction Register (IR) and Data Registers (DR) are as described in the
Test Access Port and Operation of the IEEE 1149.1 specification.
The JTAG interface is via four dedicated pins on the MCU, which are TCK, TMS, TDI, and TDO. These pins are
all 5V tolerant.
Through the 16-bit JTAG Instruction Register (IR), any of the eight instructions shown in Figure 21.1 can be
commanded. There are three Data Registers (DR’s) associated with JTAG Boundary-Scan, and four associated with
Flash read/write operations on the MCU.
Figure 21.1. IR: JTAG Instruction Register
Reset Value
0x0004
Bit15
Bit0
IR value Instruction Description
0x0000 EXTEST Selects the Boundary Data Register for control and observability of all
device pins
0x0002 SAMPLE/
PRELOAD Selects the Boundary Data Register for observability and presetting the
scan-path latches
0x0004 IDCODE Selects device ID Register
0xFFFF BYPASS Selects Bypass Data Register
0x0082 Flash Control Selects FLASHCON Register to control how the interface logic responds to
reads and writes to the FLASHDAT Register
0x0083 Flash Data Selects FLASHDAT Register for reads and writes to the Flash memory
0x0084 Flash Address Selects FLASHADR Register which holds the address of all Flash read,
write, and erase operations
0x0085 Flash Scale Selects FLASHSCL Register which controls the prescaler used to generate
timing signals for Flash operations
165 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
21.1. Boundary Scan
The Data Register in the Boundary Scan path is an 87-bit shift register. The Boundary DR provides control and
observability of all th e device pins as well as the SFR bus and Weak Pullup featur e via the EXTEST and SAMPLE
commands.
Table 21.1. Boundary Data Register Bit Definitions
EXTEST provides access to both capture and update actions, while Sample only performs a capture.
Bit Action Target
0 Capture Reset Enable from MCU
Update Reset Enable to /RST pin
1 Capture Reset input from /RST pin
Update Reset output to /RST pin
2 Capture External Clock from XTAL1 pin
Update Not used
3 Capture Weak pullup enable from MCU
Update Weak pullup enable to Port Pins
4-11 Capture SFR Address Bus bit from CIP-51 (e.g. Bit4=SFRA0, Bit5=SFRA1…)
Update SFR Address Bus bit to SFR Address Bu s (e.g. Bit4=XSFRA0, Bit5=XSFRA1)
12-19 Capture SFR Data Bus bit read from SFR (e.g. Bit12=SFRD0, Bit13=SFRD1…)
Update SFR Data Bus bit written to SFR (e.g. Bit12=SFRD0, Bit13=SFRD1…)
20 Capture SFR Write Strobe from CIP-51
Update SFR W r ite Strobe to SFR Bus
21 Capture SFR Read Strobe from CIP-51
Update SFR Read Strobe to SFR Bus
22 Capture SFR Read/Modify/Write Strobe from CIP-51
Update SFR Read/Modify/Write Strobe to SFR Bus
23,25,27,29,
31,33,35,37 Capture P0.n output enable from MCU (e.g. Bit23=P0.0, Bit25=P0.1, etc.)
Update P0.n output enable to pin (e.g. Bit23=P0.0oe, Bit25=P0.1oe, etc.)
24,26,28,30,
32,34,36,38 Capture P0.n input from pin (e.g. Bit24=P0.0, Bit26=P0.1, etc.)
Update P0.n output to pin (e.g. Bit24=P0.0, Bit26=P0.1, etc.)
39,41,43,45,
47,49,51,53 Capture P1.n output enable from MCU (e.g. Bit39=P1.0, Bit41=P1.1, etc.)
Update P1.n output enable to pin (e.g. Bit39=P1.0oe, Bit41=P1.1oe, etc.)
40,42,44,46,
48,50,52,54 Capture P1.n input from pin (e.g. Bit40=P1.0, Bit42=P1.1, etc.)
Update P1.n output to pin (e.g. Bit40=P1.0, Bit42=P1.1, etc.)
55,57,59,61,
63,65,67,69 Capture P2.n output enable from MCU (e.g. Bit55=P2.0, Bit57=P2.1, etc.)
Update P2.n output enable to pin (e.g. Bit55=P2.0oe, Bit57=P2.1oe, etc.)
56,58,60,62,
64,66,68,70 Capture P2.n input from pin (e.g. Bit56=P2.0, Bit58=P2.1, etc.)
Update P2.n output to pin (e.g. Bit56=P2.0, Bit58=P2.1, etc.)
71,73,75,77,
79,81,83,85 Capture P3.n output enable from MCU (e.g. Bit71=P3.0, Bit73=P3.1, etc.)
Update P3.n output enable to pin (e.g. Bit71=P3.0oe, Bit73=P3.1oe, etc.)
72,74,76,78,
80,82,84,86 Capture P3.n input from pin (e.g. Bit72=P3.0, Bit74=P3.1, etc.)
Update P3.n output to pin (e.g. Bit72=P3.0, Bit74=P3.1, etc.)
Rev. 1.7 166
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
21.1.1. EXTEST Instruction
The EXTEST instruction is accessed via the IR. The Boundary DR provides control and observability of all the
device pins as well as the SFR bus and Weak Pullup feature. All inputs to on-chip logic are set to one.
21.1.2. SAMPLE Instruction
The SAMPLE instruction is accessed via the IR. The Boundary DR provides observability and presetting of the
scan-path latches.
21.1.3. BYPASS Instruction
The BYPASS instruction is accessed via the IR. It provides access to the standard 1-bit JTAG Bypass data register.
21.1.4. IDCODE Instruction
The IDCODE instruction is accessed via the IR. It provides access to the 32-bit Device ID register.
Figure 21.2. DEVICEID: JTAG Device ID Register
Reset Value
Version Part Number Manufacturer ID 1 (Varies)
Bit31 Bit28 Bit27 Bit12 Bit11 Bit1 Bit0
Version = 0000b (Revision A) or
= 0001b (Revision B)
Part Number = 0000 0000 0000 0000b or
= 0000 0000 0000 0010b
Manufacturer ID = 0010 0100 001b (Silicon Laboratories)
167 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
21.2. Flash Programming Commands
The Flash memory can be programmed directly over the JTAG interface using the Flash Control, Flash Data, Flash
Address, and Flash Scale registers. These Indirect Data Registers are accessed via the JTAG Instruction Register.
Read and write operations on indirect data registers are performed by first setting the appr opriate DR address in th e
IR register. Each read or write is then in itiated by writing the approp riate Indirect Operation Code (Ind OpCode) to
the selected data register. Incoming commands to this register have the following format:
19:18 17:0
IndOpCode WriteData
IndOpCode: These bit set the operation to perform according to the following table:
IndOpCode Operation
0x Poll
10 Read
11 Write
The Poll operation is used to check the Busy bit as described below. Although a Capture-DR is performed, no
Update-DR is allowed for the Poll operation. Since updates are disabled, polling can be accomplished by shifting
in/out a single bit.
The Read operation in itiates a read from the register addressed by the IR. Reads can be in itiated by shifting only 2
bits into the indirect register. After the read operation is initiated, polling of the Busy bit must be performed to
determine when the operation is complete.
The write operation initiates a write o f WriteData to the register addressed b y the IR. Registers of any width up to
18 bits can be written. If the register to be written contains fewer than 18 bits, the data in WriteData should be left-
justified, i.e. its MSB should occupy bit 17 above. This allows shorter registers to be written in fewer JTAG clock
cycles. For example, an 8-bit register could b e written by shifting only 10 bits. After a Write is initiated, the Busy
bit should be polled to determine when the next operation can be initiated. The contents of the Instruction Register
should not be altered while either a read or write operation is in progress.
Outgoing data from the indirect Data Register has the following format:
19 18:1 0
0 ReadData
Busy
The Busy bit indicates that the current operation is not complete. It goes high when an operation is initiated and
returns low when complete. Read and Write commands are ignored while Busy is high. In fact, if polling for Busy
to be low will be followed by another read or write operation , JTAG writes of the n ext operatio n can be made while
checking for Busy to be low. They will be ignored until Busy is read low, at which time the new operation will
initiate. This bit is placed at bit 0 to allow polling by single-bit shifts. When waiting for a Read to complete and
Busy is 0, the following 18 bits can be shifted out to obtain the resulting data. ReadData is always right-justified.
This allows registers shorter than 18 bits to be read using a reduced number of shifts. For example, the result from a
byte-read requires 9 bit shifts (Busy + 8 bits).
Rev. 1.7 168
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 21.3. FLASHCON: JTAG Flash Control Register
Reset Value
WRMD3 WRMD2 WRMD1 WRMD0 RDMD3 RDMD2 RDMD1 RDMD0 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
Figure 21.4. FLASHADR: JTAG Flash Address Register
Reset Value
0x0000
Bit15 Bit0
This register determines how the Flash interface logic will respond to reads and writes to the
FLASHDAT Register.
Bits7-4: WRMD3-0: Write Mode Select Bits.
The Write Mode Select Bits control how the interface logic responds to writes to the
FLASHDAT Register per the following values:
0000: A FLASHDAT write replaces the data in the FLASHDAT register, but is otherwise
ignored.
0001: A FLASHDAT write initiates a write of FLASHDAT into the memory location
addressed by the FLASHADR register. FLASHADR is incremented by one when
complete.
0010: A FLASHDAT write initiates an erasure (sets all bytes to 0xFF) of the Flash page
containing the address in FLASHADR. FLASHDAT must be 0xA5 for the erase to
occur. FLASHADR is not affected. If FLASHADR = 0x7DFE – 0x7DFF, the entire
user space will be erased (i.e. entire Flash memory except for Reserved area 0x7E00 –
0x7FFF).
(All other values for WRMD3-0 are reserved.)
Bits3-0: RDMD3-0: Read Mode Select Bits.
The Read Mode Select Bits control how the interface logic responds to reads to the
FLASHDAT Register per the following values:
0000: A FLASHDAT read provides the data in the FASHDAT register, but is otherwise
ignored.
0001: A FLASHDAT read initiates a read of the byte addressed by the FLASHADR register
if no operation is currently active. This mode is used for block reads.
0010: A FLASHDAT read initiates a read of the byte addressed by FLASHADR only if no
operation is active and any data from a previous read has already been read from
FLASHDAT. This mode allows single bytes to be read (or the last byte of a block)
without initiating an extra read.
(All other values for RDMD3-0 are reserved.)
This register holds the address for all JTAG Flash read, write, and erase operations. This register
autoincrements after each read or write, regardless of whether the operation succeeded or failed.
Bits15-0: Flash Operation 16-bit Address.
169 Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 21.5. FLASHDAT: JTAG Flash Data Register
Reset Value
DATA7 DATA6 DATA5 DATA4 DATA3 DATA2 DATA1 DATA0 FAIL FBUSY 0000000000
Bit9 Bit8 Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
Figure 21.6. FLASHSCL: JTAG Flash Scale Register
Reset Value
FOSE FRAE - - FLSCL3 FLSCL2 FLSCL1 FLSCL0 00000000
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
This register is used to read or write data to the Flash memory across the JTAG interface.
Bits9-2: DATA7-0: Flash Data Byte.
Bit1: FAIL: Flash Fail Bit.
0: Previous Flash memory operation was successful.
1: Previous Flash memory operation failed. Usually indicates the associated memory
location was locked.
Bit0: FBUSY: Flash Busy Bit.
0: Flash interface logic is not busy.
1: Flash interface logic is processing a request. Reads or writes while FBUSY = 1 will
not initiate another operation
This register controls the Flash read timing circuit and the prescaler required to generate the correct
timing for Flash operations.
Bit7: FOSE: Flash One-Shot Enable Bit.
0: Flash read strobe is a full clock-cycle wide.
1: Flash read strobe is 50nsec.
Bit6: FRAE: Flash Read Always Bit.
0: The Flash output enable and sense amplifier enable are on only when needed to read the
Flash memory.
1: The Flash output enable and sense amplifier enable are always on. This can be used to
limit the variations in digital supply current due to switching the sense amplifiers, thereby
reducing digitally induced noise.
Bits5-4: UNUSED. Read = 00b, W r ite = don’t care.
Bits3-0: FLSCL3-0: Flash Prescaler Contro l Bits.
The FLSCL3-0 bits control the prescaler used to generate timing signals for Flash
operations. Its value should be written before any Flash operations are initiated. The value
written should be the smallest integer for which:
FLSCL[3:0] > log2(fSYSCLK / 50kHz)
Where fSYSCLK is the system clock frequency. All Flash read/write/erase operations are
disallowed when FLSCL
[
3:0
]
= 1111b.
Rev. 1.7 170
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
21.3. Debug Support
Each MCU has on-chip JTAG and debug circuitry that provide non-intrusive, full speed, in-circuit debug using the
production part installed in the end application using the four pin JTAG I/F. Silicon Labs’ debug system supports
inspection and modification of memory and registers, setting breakpoints, watchpoints, single stepping, and run and
halt commands. No additional target RAM, program memory, or communications channels are required. All the
digital and analog peripherals are functional and work correctly (remain in sync) while debugging. The WDT is
disabled when the MCU is halted during single stepping or at a breakpoint.
The C8051F000DK, C8051F005DK, C8051F010DK, and C8051F015DK are development kits with all the
hardware and software necessary to develop application code and perform in-circuit debugging with each MCU in
the C8051F000 family. Each kit includes an Integrated Development Environment (IDE) which has a debugger and
integrated 8051 assembler. It has an RS-232 to JTAG protocol translator module referred to as the EC. There is
also a target application board with a C8051F000, F005, F010, or F015 installed and with a large prototyping area.
The kit also includes RS-232 and JTAG cables, and wall-mount power supply.
http://www.silabs.com
Silicon Laboratories Inc.
400 West Cesar Chavez
Austin, TX 78701
USA
Simplicity Studio
One-click access to MCU and
wireless tools, documentation,
software, source code libraries &
more. Available for Windows,
Mac and Linux!
IoT Portfolio
www.silabs.com/IoT SW/HW
www.silabs.com/simplicity Quality
www.silabs.com/quality Support and Community
community.silabs.com
Disclaimer
Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers using
or intending to use the Silicon Laboratories products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and
"Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Laboratories reserves the right to
make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the
included information. Silicon Laboratories shall have no liability for the consequences of use of the information supplied herein. This document does not imply or express copyright licenses
granted hereunder to design or fabricate any integrated circuits. The products are not designed or authorized to be used within any Life Support System without the specific written consent
of Silicon Laboratories. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected to result in significant
personal injury or death. Silicon Laboratories products are not designed or authorized for military applications. Silicon Laboratories products shall under no circumstances be used in
weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons.
Trademark Information
Silicon Laboratories Inc.® , Silicon Laboratories®, Silicon Labs®, SiLabs® and the Silicon Labs logo®, Bluegiga®, Bluegiga Logo®, Clockbuilder®, CMEMS®, DSPLL®, EFM®, EFM32®,
EFR, Ember®, Energy Micro, Energy Micro logo and combinations thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZRadio®, EZRadioPRO®, Gecko®,
ISOmodem®, Precision32®, ProSLIC®, Simplicity Studio®, SiPHY®, Telegesis, the Telegesis Logo®, USBXpress® and others are trademarks or registered trademarks of Silicon Laborato-
ries Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand
names mentioned herein are trademarks of their respective holders.
