QCA9377
QCA9377 includes both
dual-band 1x1 802.11ac and
Bluetooth 4.2 features
QCA9377 combines advanced 1x1 dual-band
802.11ac MU-MIMO Wi-Fi + Bluetooth 4.2 in
a high performance, ultra low power, small
form factor System-on-Chip (SoC).
Designed to deliver superior integration of WLAN
and Bluetooth low energy technology in a single-chip
solution, the QCA9377 SoC oers both low power
dual-band (2.4 & 5GHz), 1-stream (1x1), 802.11ac
MU-MIMO and Bluetooth 4.2 technologies.
QCA9377 supports high-speed Wi-Fi connectivity
and enriched media experiences for virtually all
connected devices. It is optimized for energy
eiciency, which is critical to extending the battery
life of portable devices. The software stack oers
quality, stability and performance with an open
source option and the architecture allows for virtually
seamless evolution.
QCA9377 allows for superior rate-over-range
throughput and low-latency performance in
real-world operating conditions by incorporating
Bluetooth coexistence, a special periodic switching
of the antenna designed to enable both Wi-Fi and
Bluetooth to operate in the same module eectively
at the same time.
The two variants available for QCA9377 are
QCA9377-3, which supports a low-power SDIO 3.0
interface for WLAN and a UART/PCM interface for
Bluetooth and QCA9377-7, which supports a low-
power USB 2.0 interface for WLAN and a USB 1.1
interface for Bluetooth.
Qualcomm Wi-Fi Solutions and QCA9377 are products of Qualcomm Technologies, Inc.
Advanced 802.11ac combo SoC
Advanced 802.11ac features such as MU-MIMO, Host
wake-on-wireless and ARP (Address Resolution Protocol)
offloading enable the WLAN link to remain associated for
extended periods for additional power savings.
Supports dual-mode Bluetooth
version 4.2
QCA9377 supports Bluetooth for Class-1 and Class-2
transmissions without requiring an external power amplifier.
Advanced Bluetooth/WLAN
coexistence and concurrent RX
WLAN/Bluetooth coexistence allows for superior rate-
over-range throughput and low-latency performance in
real-world operating conditions.
Power saving techniques for
ultra low power consumption
Both WLAN and Bluetooth power management utilize
advanced power saving techniques such as:
- gating clocks to idle or inactive blocks
- voltage scaling
- fast start and settling circuits
- active duty cycles
- processor frequency scaling
Qualcomm®
Wi-Fi Solutions for the IoT
Solution Highlights
Materials are subject to change without notice.
87-YB797-1 Rev A
High performance, ultra low power
single-stream 11ac MU-MIMO and
Bluetooth® 4.2 in a single-chip solution
©2017 Qualcomm Technologies, Inc. All Rights Reserved. Qualcomm is a trademark of Qualcomm Incorporated, registered in the United
States and other countries, used with permission. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG,
Inc. and any use of such marks by Qualcomm Technologies, Inc. is under license. Other products and brand names may be trademarks or
registered trademarks of their respective owners. 0517B
Features
£
1x1 802.11ac + Bluetooth 4.2 in a single SoC
£
Supports Bluetooth 4.2 + HS, Bluetooth low
energy and is backward compatible with
Bluetooth 1.x and 2.x
£
Single regulated 3.3V supply operation
£
Integrated RF Front End, single ended design
£
Oloading for minimal host utilization
£
Low-density parity check (LDPC)
encoding/decoding
£
STBC, MU-MIMO, Transmit Beam-forming
£
1.5KB OTP to eliminate an external ash
£
256-QAM in 2.4GHz
£
Enhanced Coexistence Bluetooth and LTE;
concurrent operation
£
PCB friendly: WLP to go on 4-L FR4
non-HDI PCB
£
Provides a 48MHz reference clock
£
1216KBRAM and 448KB ROMfor Wi-Fi
£
192KB RAM and 672KB ROMfor Bluetooth
For additional product
information and updates go
to: developer.qualcomm.com/
hardware/qca9377
QCA9377 Block Diagram
QCA9377 Specifications
Package
4.32 x 5.46mm, 115-pin WLNSP, 0.566mm pitch
WLAN Technology 1x1 802.11 a/b/g/n/ac with advanced features
Bluetooth Technology Bluetooth v4.2 + HS
PCB Footprint (unshielded) Die size: 23.25 mm2; PCB <110 mm2
Interfaces WLAN: SDIO 3.0 4b | Bluetooth: UART/PCM (QCA9377-3)
WLAN: USB 2.0 | Bluetooth: USB+LPM/L1 (QCA9377-7)
Antenna Conguration Single Wi-Fi/Bluetooth antenna
WLAN Channel Bandwidths 20/40/80MHz
WLAN TCP/IP Throughput USB2.0: up to 260 Mbps
80MHz 11ac SDIO3.0 4b SDR104: up to 330 Mbps
Bluetooth RX Sensitivity -96dBm GFSK
Power Supply Regulated 3.3V
Applications
IoT Smart Appliances Wireless Gaming Home Automation Industrial Automation Infotainment
Product Part Number
QCA9377-3 SOC QCA9377-3-115WLNSP-03
QCA9377-7 SOC QCA9377-7-115WLNSP
Ordering Information