14,000/sec Digital Gyroscope Sensor ADIS16266 Data Sheet FEATURES GENERAL DESCRIPTION Yaw rate gyroscope with range scaling 3500/sec, 7000/sec, and 14,000/sec settings 2429 SPS sample rate Wide sensor bandwidth: 360 Hz No external configuration required to start data collection Start-up time: 170 ms Sleep mode recovery time: 2.5 ms Factory-calibrated sensitivity and bias Calibration temperature range: -40C to +70C SPI-compatible serial interface Embedded temperature sensor Programmable operation and control Automatic and manual bias correction controls Bartlett window FIR filter length, number of taps Digital input/output: data ready, alarm indicator, general-purpose Alarms for condition monitoring Sleep mode for power management DAC output voltage Single-command self-test Single-supply operation: 4.75 V to 5.25 V 3.3 V compatible digital lines 2000 g shock survivability Operating temperature range: -40C to +105C The ADIS16266 is a programmable digital gyroscope that combines industry-leading MEMS and signal processing technology in a single compact package. It provides accuracy performance that would otherwise require full motion calibration with any other MEMS gyroscope in this performance class. When power is applied, the ADIS16266 automatically starts up and begins sampling sensor data, without requiring configuration commands from a system processor. An addressable register structure and a common serial peripheral interface (SPI) provide simple access to sensor data and configuration settings. Many digital processor platforms support the SPI with simple firmware level instructions. The ADIS16266 provides several programmable features for in-system optimization. The Bartlett window FIR filter length and sample rate settings provide users with controls that enable noise vs. bandwidth optimization. The digital input/output lines offer options for a data ready signal that helps the master processor efficiently manage data coherency, an alarm indicator signal for triggering master processor interrupts, and a general-purpose function for setting and monitoring system level digital controls/ conditions. The ADIS16266 is pin-compatible with the ADIS16265 and comes in an LGA package (11.2 mm x 11.2 mm x 5.5 mm) that meets Pb-free solder reflow profile requirements, per JEDEC J-STD-020. It offers an extended operating temperature range of -40C to +105C. APPLICATIONS Platform control and stabilization Navigation Medical instrumentation Robotics FUNCTIONAL BLOCK DIAGRAM DIO1 DIO2 RST SELF-TEST RATE MEMS GYROSCOPE SENSOR INPUT/ OUTPUT VCC ALARMS POWER MANAGEMENT GND FILT POWER SUPPLY AUX ADC VREF AUX DAC CLOCK USER CONTROL REGISTERS SPI PORT FILTER OUTPUT DATA REGISTERS CALIBRATION ADIS16266 CS SCLK DIN DOUT 11117-001 CONTROLLER TEMPERATURE SENSOR Figure 1. Rev. B Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 (c)2012-2015 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com ADIS16266 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Output Data Registers ............................................................... 12 Applications ....................................................................................... 1 Device Configuration ................................................................ 13 General Description ......................................................................... 1 Digital Signal Processing ............................................................... 14 Functional Block Diagram .............................................................. 1 Decimation Filter (Update Rate) .............................................. 14 Revision History ............................................................................... 2 Frequency Response .................................................................. 14 Specifications..................................................................................... 3 Dynamic Range .......................................................................... 14 Timing Specifications .................................................................. 5 Calibration ....................................................................................... 15 Absolute Maximum Ratings............................................................ 6 System Tools .................................................................................... 16 ESD Caution .................................................................................. 6 Diagnostics .................................................................................. 17 Pin Configuration and Function Descriptions ............................. 7 Alarms .............................................................................................. 18 Typical Performance Characteristics ............................................. 8 Product Identification................................................................ 19 Theory of Operation ........................................................................ 9 Applications Information .............................................................. 20 Sensing Element ........................................................................... 9 Assembly...................................................................................... 20 Data Sampling and Processing ................................................... 9 Bias Optimization....................................................................... 20 User Interface ................................................................................ 9 Interface PCB .............................................................................. 21 Basic Operation............................................................................... 10 Outline Dimensions ....................................................................... 22 Reading Sensor Data .................................................................. 10 Ordering Guide .......................................................................... 22 User Registers .................................................................................. 11 REVISION HISTORY 7/15--Rev. A to Rev. B Change to Features Section ............................................................. 1 1/14--Rev. 0 to Rev. A Changes to General Description Section ...................................... 1 10/12--Revision 0: Initial Version Rev. B | Page 2 of 24 Data Sheet ADIS16266 SPECIFICATIONS TA = -40C to +105C, VCC = 5.0 V, angular rate = 0/sec, 1 g, 14,000/sec range setting, unless otherwise noted. Table 1. Parameter SENSITIVITY 1 Initial Tolerance Temperature Coefficient Nonlinearity BIAS Initial Error In-Run Bias Stability Angular Random Walk Linear Acceleration Effect Temperature Coefficient Voltage Sensitivity NOISE PERFORMANCE Output Noise Rate Noise Density FREQUENCY RESPONSE 3 dB Bandwidth Sensor Resonant Frequency SELF-TEST STATE Change for Positive Stimulus Change for Negative Stimulus Internal Self-Test Cycle Time ADC INPUT Resolution Integral Nonlinearity Differential Nonlinearity Offset Error Gain Error Input Range Input Capacitance ON-CHIP VOLTAGE REFERENCE Accuracy Temperature Coefficient Output Impedance DAC OUTPUT Resolution Relative Accuracy Differential Nonlinearity Offset Error Gain Error Output Range Output Impedance Output Settling Time Test Conditions/Comments Clockwise rotation is positive output 25C, dynamic range = 14,000/sec 2 25C, dynamic range = 7000/sec 25C, dynamic range = 3500/sec 25C, dynamic range = 14000/sec, VDD = 5 V 4.75 V < VDD < 5.25 V Best fit straight line Min Typ 4.17 2.08 1.04 0.5 200 0.1 Max 2 Unit /sec/LSB /sec/LSB /sec/LSB % ppm/C % of FS VCC = 4.75 V to 5.25 V, 1 15 470 21.5 0.1 0.35 7.5 /sec /hour /hour /sec/g /sec/C /sec/V 25C, 14,000/sec range, no filtering 25C, 7000/sec range, 4-tap filter setting 25C, 3500/sec range, 16-tap filter setting 25C, f = 25 Hz, 14,000/sec range, no filtering 11.2 7.2 3.4 0.44 /sec rms /sec rms /sec rms /sec/Hz rms 25C, 1 25C, 1 25C, 1 16 14,000/sec dynamic range setting 14,000/sec dynamic range setting 360 18 150 -500 20 500 -150 30 12 2 1 4 2 0 During acquisition 2.5 20 2.5 25C -10 +10 40 70 Hz kHz LSB LSB ms Bits LSB LSB LSB LSB V pF V mV ppm/C 5 k/100 pF to GND 12 4 1 5 0.5 For Code 101 to Code 4095 0 2.5 2 10 Rev. B | Page 3 of 24 Bits LSB LSB mV % V s ADIS16266 Parameter LOGIC INPUTS Input High Voltage, VINH Input Low Voltage, VINL Logic 1 Input Current, IINH Logic 0 Input Current, IINL All Except RST RST Input Capacitance, CIN DIGITAL OUTPUTS Output High Voltage, VOH Output Low Voltage, VOL SLEEP TIMER Timeout Period 3 START-UP TIME Initial Start-Up Time Sleep Mode Recovery Reset Recovery Flash Memory Update Time Flash Memory Test Time Self-Test Time FLASH MEMORY Endurance 4 Data Retention 5 CONVERSION RATE Sample Rate Sample Rate Tolerance POWER SUPPLY Operating Voltage Range, VCC Power Supply Current Data Sheet Test Conditions/Comments Internal 3.3 V interface Min Typ Max Unit 0.2 0.8 10 V V A 2.0 VIH = 3.3 V VIL = 0 V -40 -1 10 The RST pin has an internal pull-up. Internal 3.3 V interface ISOURCE = 1.6 mA ISINK = 1.6 mA -60 2.4 0.5 0.4 V V 128 sec 170 2.5 78 40 18 30 ms ms ms ms ms ms 20,000 10 TJ = 55C Cycles Years 2429 3 4.75 Sleep mode A mA pF 5.0 41 400 5.25 SPS % V mA A Characterization data represents 4 to fall within the 1% limit. The maximum guaranteed measurement range is 14,000/sec. The sensor outputs measure beyond this range, but performance is guaranteed. 3 Guaranteed by design. 4 Endurance is qualified as per JEDEC Standard 22, Method A117, and measured at -40C, +25C, +85C, and +125C. 5 Retention lifetime equivalent at a junction temperature (TJ) of 55C, as per JEDEC Standard 22, Method A117. Retention lifetime decreases with junction temperature. 1 2 Rev. B | Page 4 of 24 Data Sheet ADIS16266 TIMING SPECIFICATIONS TA = -40C to +85C, VCC = 5.0 V, unless otherwise noted. Table 2. Min1 0.01 32 9 48.8 Parameter fSCLK tDATARATE tSTALL tCS Description Serial clock (not shown in figures) Data rate period Stall period between data Chip select to clock edge tDAV tDSU tDHD tDF tDR tSFS Data output valid after SCLK falling edge2 Data input setup time before SCLK rising edge Data input hold time after SCLK rising edge Data output fall time (not shown in figures) Data output rise time (not shown in figures) CS high after SCLK edge3 Typ Max1 2.5 Unit MHz s s ns 100 ns ns ns ns ns ns 24.4 48.8 5 5 12.5 12.5 5 1 Guaranteed by design; not production tested. The MSB presents an exception to this parameter. The MSB clocks out on the falling edge of CS. The remaining DOUT bits are clocked after the falling edge of SCLK and are governed by this specification. 3 This parameter may need to be expanded to allow for proper capture of the LSB. After CS goes high, the DOUT line enters a high impedance state. 2 Timing Diagrams tDATARATE CS 11117-002 SCLK tSTALL Figure 2. SPI Chip Select Timing CS tCS tSFS 1 SCLK 2 3 4 5 6 15 16 tDAV * MSB DB14 DB13 tDSU DIN R/W DB12 DB11 A4 A3 DB10 DB2 DB1 LSB tDHD A5 A2 D2 D1 *NOT DEFINED Figure 3. SPI Timing (Using SPI Settings Typically Identified as CPOL = 1, CPHA = 1) Rev. B | Page 5 of 24 LSB 11117-003 DOUT ADIS16266 Data Sheet ABSOLUTE MAXIMUM RATINGS Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability. Table 3. Parameter Acceleration Any Axis, Unpowered, 0.5 ms Any Axis, Powered, 0.5 ms VCC to GND Digital Input/Output Voltage to GND Analog Inputs to GND Operating Temperature Range1 Storage Temperature Range1 1 Rating 2000 g 2000 g -0.3 V to +6.0 V -0.3 V to +5.3 V -0.3 V to +3.5 V -40C to +105C -65C to +150C ESD CAUTION Extended exposure to temperatures outside the temperature range of -40C to +85C can adversely affect the accuracy of the factory calibration. For best accuracy, store the part within the temperature range of -40C to +85C. Rev. B | Page 6 of 24 Data Sheet ADIS16266 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS VREF GND GND VCC VCC 19 18 17 16 1 DOUT 2 DIN 3 CS 4 DIO1 5 ADIS16266 TOP VIEW (Not to Scale) POSITIVE OUTPUT ROTATIONAL DIRECTION 6 7 8 9 15 FILT 14 RATE 13 AUX ADC 12 AUX DAC 11 DNC 10 DIO2 RST DNC DNC DNC NOTES 1. DNC = DO NOT CONNECT. 2. THE PINS CANNOT BE SEEN FROM THE TOP. THIS LOOK-THOUGH VIEW OF THEIR LOCATION IS OFFERED FOR REFERENCE IN DEVELOPING PCB PATTERNS. 11117-004 20 SCLK Figure 4. Pin Configuration AXIS OF ROTATION PIN 10 PIN 1 PIN 6 NOTES 1. ARROW INDICATES THE DIRECTION OF ROTATION THAT PRODUCES A POSITIVE RESPONSE IN THE GYRO_OUT REGISTER. 11117-005 PIN 5 Figure 5. Axial Orientation Table 4. Pin Function Descriptions Pin No. 1 2 3 4 5, 6 7 8, 9, 10, 11 12 13 14 15 16, 17 18, 19 20 1 Mnemonic SCLK DOUT DIN CS DIO1, DIO2 RST DNC AUX DAC AUX ADC RATE FILT VCC GND VREF Type1 I O I I I/O I O I O I S S O Description SPI Serial Clock. SPI Data Output. DOUT clocks the output on the falling edge of SCLK. SPI Data Input. DIN clocks the input on the rising edge of SCLK. SPI Chip Select. Active low. Configurable Digital Input/Output. Reset. Active low. Do Not Connect. Auxiliary DAC Output. Auxiliary ADC Input. Rate Output. For bandwidth reduction only, the output is not specified. Filter Terminal. 5.0 V Power Supply. Ground. Precision Reference Output. I = input, I/O = input/output, O = output, and S = supply. Rev. B | Page 7 of 24 ADIS16266 Data Sheet TYPICAL PERFORMANCE CHARACTERISTICS 10k 2.5 RELATIVE ERROR (% ERROR) + 1k - 0.1 1 10 100 10k 1k Tau (Seconds) Figure 6. Allan Variance Plot 40 20 0 -20 -40 -60 0 20 40 TEMPERATURE (C) 60 80 11117-007 RELATIVE ERROR (/sec) 60 -20 0.5 0 -0.5 -1.0 -1.5 -2.5 -40 -20 0 20 40 60 TEMPERATURE (C) Figure 8. Sensitivity vs. Temperature 80 -80 -40 1.0 -2.0 11117-006 100 0.01 1.5 Figure 7. Bias vs. Temperature Rev. B | Page 8 of 24 80 11117-008 ALLAN DEVIATION (/Hour) 2.0 Data Sheet ADIS16266 The sensing element operates on the principle of a resonator gyro. Two polysilicon sensing structures each contain a dither frame that is electrostatically driven to resonance, producing the necessary velocity element to generate a Coriolis force during angular rate. At two of the outer extremes of each frame, orthogonal to the dither motion, movable fingers are placed between fixed pickoff fingers to form a capacitive pickoff structure that senses Coriolis motion. The resulting signal is fed into a series of gain and demodulation stages that produce the electrical rate signal output. The differential structure minimizes the response to linear acceleration (gravity, vibration, and so on) and EMI. DATA SAMPLING AND PROCESSING The ADIS16266 runs autonomously, based on the configuration in the user control registers. The analog gyroscope signal feeds into an analog-to-digital converter (ADC) stage, which passes digitized data into the controller for data processing and register loading. Data processing in the embedded controller includes correction formulas, filtering, and checking for preset alarm conditions. The correction formulas are unique for each individual ADIS16266 and come from the factory characterization of each device over a temperature range of -40C to +70C. ADC CONTROLLER CONTROL REGISTERS AIN SIGNALS SPI PORT TEMP SENSOR OUTPUT REGISTERS CLOCK Figure 9. Simplified Sensor Signal Processing Diagram USER INTERFACE SPI Interface Data collection and configuration commands both use the SPI, which consists of four wires. The chip select (CS) signal activates the SPI interface, and the serial clock (SCLK) signal synchronizes the serial data lines. The serial input data clocks into DIN on the SCLK rising edge, and the serial output data clocks out of DOUT on the SCLK falling edge. Many digital processor platforms support this interface with dedicated serial ports and simple instruction sets. User Registers The user registers provide addressing for all input/output operations on the SPI interface. Each 16-bit register has its own unique bit assignment and has two 7-bit addresses: one for its upper byte and one for its lower byte. Table 7 provides a memory map of the user registers, along with the function of each register. Rev. B | Page 9 of 24 11117-009 SENSING ELEMENT MEMS SENSOR SPI PORT The ADIS16266 integrates a MEMS gyroscope with data sampling, signal processing, and calibration functions, along with a simple user interface. This sensing system collects data autonomously and makes it available to any processor system that supports a 4-wire serial peripheral interface (SPI). SPI SIGNALS THEORY OF OPERATION ADIS16266 Data Sheet BASIC OPERATION The ADIS16266 is an autonomous system that requires no user initialization. As soon as it has a valid power supply, it initializes and starts sampling, processing, and loading sensor data into the output registers. After each sample cycle concludes, DIO1 pulses high. The SPI interface enables simple integration with many embedded processor platforms, as shown in Figure 10 (electrical connection) and Table 5 (processor pin names and functions). VDD READING SENSOR DATA 5V 16 SYSTEM PROCESSOR SPI MASTER A single register read requires two 16-bit SPI cycles. The first cycle requests the contents of a register using the bit assignments in Figure 13. Then, the register contents follow on DOUT during the second sequence. Figure 11 includes three single register reads in succession. In this example, the process starts with Pin 3, DIN = 0x0400, to request the contents of the GYRO_OUT register and follows with 0x0600 to request the contents of the GYRO_OUT2 register and with 0x0C00 to request the contents of the TEMP_OUT register. Full duplex operation enables processors to use the same 16-bit SPI cycle to read data from DOUT while requesting the next set of data on the DIN pin. Figure 12 provides an example of the four SPI signals when reading GYRO_OUT in a repeating pattern. 17 VCC VCC 4 CS 1 SCLK MOSI 3 DIN MISO 2 DOUT IRQ 5 DIO1 ADIS16266 GND GND 18 19 11117-011 SS SCLK Figure 10. Electrical Connection Diagram Table 5. Generic Master Processor Pin Names and Functions Pin Name SS IRQ MOSI MISO SCLK Description ADIS16266 operates as a slave Maximum serial clock rate CPOL = 1 (polarity), CPHA = 1 (phase) Bit sequence Shift register/data length Function Slave select Interrupt request Master output, slave input Master input, slave output Serial clock DIN 0x0400 DOUT 0x0600 0x0C00 GYRO_OUT GYRO_OUT2 TEMP_OUT 11117-012 INPUT/OUTPUT LINES ARE COMPATIBLE WITH 3.3V OR 5V LOGIC LEVELS Table 6. Generic Master Processor SPI Settings Processor Setting Master SCLK Rate 2.5 MHz SPI Mode 3 MSB First Mode 16-Bit Mode Figure 11. SPI Read Example CS SCLK DIN DIN = 0000 0100 0000 0000 = 0x0400 DOUT DOUT = 1011 1001 1101 1010 = NEW DATA, 0x39DA = -1574 LSBs = -6,563.58/sec Figure 12. SPI Read Example, Second 16-Bit Sequence CS DIN DOUT R/W D15 A6 A5 A4 A3 A2 A1 A0 DC7 DC6 DC5 DC4 DC3 DC2 DC1 DC0 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 R/W D15 A6 A5 D14 D13 NOTES 1. DOUT BITS ARE PRODUCED ONLY WHEN THE PREVIOUS 16-BIT DIN SEQUENCE STARTS WITH R/W = 0. 2. WHEN CS IS HIGH, DOUT IS IN A THREE-STATE, HIGH IMPEDANCE MODE, WHICH ALLOWS MULTIFUNCTIONAL USE OF THE LINE FOR OTHER DEVICES. Figure 13. SPI Communication Bit Sequence Rev. B | Page 10 of 24 11117-014 SCLK 11117-013 The SPI interface of the ADIS16266 supports full duplex serial communication (simultaneous transmit and receive) and uses the bit sequence shown in Figure 13. Table 6 provides a list of the most common settings that require attention to initialize a processor serial port for the SPI interface of the ADIS16266. Data Sheet ADIS16266 USER REGISTERS Table 7. User Register Memory Map Name FLASH_CNT SUPPLY_OUT GYRO_OUT GYRO_OUT2 Reserved AUX_ADC TEMP_OUT Reserved GYRO_OFF GYRO_SCALE Reserved ALM_MAG1 ALM_MAG2 ALM_SMPL1 ALM_SMPL2 ALM_CTRL Reserved AUX_DAC GPIO_CTRL MSC_CTRL SMPL_PRD SENS_AVG SLP_CNT DIAG_STAT GLOB_CMD R/W R R R R N/A2 R R N/A2 R/W R/W N/A2 R/W R/W R/W R/W R/W N/A2 R/W R/W R/W R/W R/W W R W Flash Backup Yes No No No N/A2 No No N/A2 Yes Yes N/A2 Yes Yes Yes Yes Yes N/A2 No No Yes Yes Yes Yes No No LOT_ID1 LOT_ID2 PROD_ID SERIAL_NUM R R R R Yes Yes Yes Yes 1 2 Address1 0x00 0x02 0x04 0x06 0x08 0x0A 0x0C 0x0F to 0x13 0x14 0x16 0x18 to 0x1F 0x20 0x22 0x24 0x26 0x28 0x2B to 0x2F 0x30 0x32 0x34 0x36 0x38 0x3A 0x3C 0x3E 0x40 to 0x51 0x52 0x54 0x56 0x58 Default N/A2 N/A2 N/A2 N/A2 N/A2 N/A2 N/A2 N/A2 0x0000 0x0800 N/A2 0x0000 0x0000 0x0000 0x0000 0x0000 N/A2 0x0000 0x0000 0x0006 0x0000 0x0401 N/A2 N/A2 N/A2 N/A2 N/A N/A2 0x3F8A N/A2 Register Description Flash memory write count Output, power supply Output, gyroscope Output, gyroscope, bit growth from decimation Reserved Output, auxiliary ADC measurement Output, temperature (internal) Reserved Gyroscope bias correction Gyroscope scale correction Reserved Alarm 1 trigger setting Alarm 2 trigger setting Alarm 1 sample period Alarm 2 sample period Alarm configuration Reserved Control, DAC output voltage setting Control, digital input/output line Control, data ready, self-test settings Control, internal sample rate Control, dynamic range, filtering Control, sleep mode initiation Diagnostic, error flags Control, global commands Reserved Lot Identification Code 1 Lot Identification Code 2 Product identifier; 16,266 Serial number Bit Descriptions See Table 27 See Table 13 See Table 8 See Table 10 See Table 15 See Table 11 See Table 19 See Table 20 See Table 30 See Table 31 See Table 32 See Table 33 See Table 34 See Table 25 See Table 23 See Table 24 See Table 17 See Table 18 See Table 22 See Table 29 See Table 21 See Table 37 See Table 37 See Table 37 See Table 37 Each register contains two bytes. The address column in this table only offers the address of the lower byte. Add 1 to it to calculate the address of the upper byte. N/A means not applicable. Rev. B | Page 11 of 24 ADIS16266 Data Sheet OUTPUT DATA REGISTERS Internal Temperature Figure 14 displays the generic pattern for the format of the output registers. The ND bit is equal to 1 when the register contains unread data. The EA bit is high when any error/alarm flag in the DIAG_STAT register is equal to 1. The TEMP_OUT register (see Table 11) provides access to a sensor that monitors internal temperature, which influences the calibration correction formulas for the gyroscope data. Note that this difference between internal and ambient temperatures is dependent on many factors, which can introduce variation that can approach 10C. This temperature measurement is useful for tracking relative changes in temperature. MSB FOR 14-BIT OUTPUT 11117-015 ND EA MSB FOR 12-BIT OUTPUT Figure 14. Output Register Bit Assignments Table 11. TEMP_OUT Bits (Base Address = 0x0C) Rotation Rate (Gyroscope) GYRO_OUT (see Table 8) is the primary register for gyroscope output data and uses 14-bit twos complement format for its data. Table 9 provides several examples for converting digital data into /sec. Bits 15 14 [13:12] [11:0] Table 8. GYRO_OUT Bits (Base Address = 0x04) Bits 15 14 [13:0] Description New (unread) data indicator; bit = 1 indicates new, unread data in this register Error/alarm; bit = 1 when DIAG_STAT 0x0000 Gyroscope data; twos complement, 4.17/sec per LSB, 0/sec = 0x0000 Table 9. GYRO_OUT, Twos Complement Format Rotation Rate +14000/sec +8.34/sec +4.17/sec 0/sec -4.17/sec -8.34/sec -14000/sec Decimal +3357 +2 +1 0 -1 -2 -3357 Hex 0x0D1D 0x0002 0x0001 0x0000 0x3FFF 0x3FFE 0x32E3 Binary xx00 1101 0001 1101 xx00 0000 0000 0010 xx00 0000 0000 0001 xx00 0000 0000 0000 xx11 1111 1111 1111 xx11 1111 1111 1110 xx11 0010 1110 0011 The GYRO_OUT2 register (see Table 10) captures the bit growth associated with the decimation filter (see Figure 19) using an MSB justified format. The bit growth starts with the MSB (GYRO_OUT2[15]), is equal to the decimation rate setting in SMPL_PRD[3:0] (see Table 17), and grows in the LSB direction as the decimation rate increases. Description New (unread) data indicator; bit = 1 indicates new, unread data in this register Error/alarm; bit = 1 when DIAG_STAT 0x0000 Not used Temperature data; twos complement, 0.1447C per LSB, 0C = 0x000 Table 12. Temperature, Twos Complement Format Temperature +105C +25.2894C +25.1447C +25C +24.8553C +24.7106C -40C Decimal +544 LSB +2 LSB +1 LSB 0 LSB -1 LSB -2 LSB -449 LSB Hex 0x220 0x002 0x001 0x000 0xFFF 0xFFE 0xE3F Binary Output xxxx 0010 0010 0000 xxxx 0000 0000 0010 xxxx 0000 0000 0001 xxxx 0000 0000 0000 xxxx 1111 1111 1111 xxxx 1111 1111 1110 xxxx 1110 0011 1111 Power Supply Voltage The SUPPLY_OUT (see Table 13) register provides a digital representation of the power supply voltage, across VDD and GND. Table 13. SUPPLY_OUT Bits (Base Address = 0x02) Bits 15 14 [13:12] [11:0] Description New (unread) data indicator; bit = 1 indicates new, unread data in this register Error/alarm; bit = 1 when DIAG_STAT 0x0000 Not used Power supply (VDD) data, binary (0 V = 0x000) 1.83 mV/LSB Table 10. GYRO_OUT2 Bits (Base Address = 0x06) Table 14. Power Supply Voltage Data Format Examples Bits [15:0] Supply Voltage (V) 5.25 5.0 + 0.00183 5.0 5.0 - 0.00183 4.75 Description Rotation rate data; resolution enhancement bits D 13 GYRO_OUT BIT WEIGHT = 4.17 2D NOT USED 0 15 GYRO_OUT2 /sec LSB = GYRO_OUT2[16 - D] LSB 0 11117-016 GYROSCOPE DATA D = SMPL_PRD[3:0] Figure 15. Gyroscope Output Format Rev. B | Page 12 of 24 Decimal 2867 LSB 2731 LSB 2730 LSB 2729 LSB 2594 LSB Hex 0xB33 0xAAB 0xAAA 0xAA9 0xA22 Binary Output xxxx 1011 0011 0011 xxxx 1010 1010 1011 xxxx 1010 1010 1010 xxxx 1010 1010 1001 xxxx 1010 0010 0010 Data Sheet ADIS16266 Auxiliary Input Voltage (AUX_ADC) Dual Memory Structure The AUX_ADC (see Table 15) register provides a digital representation of the voltage on the AUX_ADC pin. Writing configuration data to a control register updates its SRAM contents, which are volatile. After optimizing each relevant control register setting in a system, set GLOB_CMD[3] = 1 (DIN = 0xBE08) to back up these settings in the nonvolatile flash memory. The flash backup process requires a valid power supply level for the entire 40 ms process time. Table 7 provides a register memory map that includes a column of flash backup information. A yes in this column indicates that a register has a mirror location in flash and, when backed up properly, automatically restores itself during startup or after a reset. Figure 17 provides a diagram of the dual memory structure that is used to manage operation and store critical user settings. Bits 15 14 [13:12] [11:0] Description New (unread) data indicator; bit = 1 indicates new, unread data in this register Error/alarm; bit = 1 when DIAG_STAT 0x0000 Not used Auxiliary input voltage, binary (0 V = 0x000) 0.6105 mV/LSB Table 16. AUX_ADC Voltage Data Format Examples Input (mV) 2500 1200 0.6105 0 Decimal 4095 LSB 1966 LSB 1 LSB 0 LSB Hex 0xFFF 0x7AE 0x001 0x000 Binary Output xxxx 1111 1111 1111 xxxx 0111 1010 1110 xxxx 0000 0000 0001 xxxx 0000 0000 0000 DEVICE CONFIGURATION CS 11117-017 SCLK DIN = 1011 0010 0000 0011 = 0xB203, WRITES 0x03 TO ADDRESS 0x32 NONVOLATILE FLASH MEMORY VOLATILE SRAM (NO SPI ACCESS) SPI ACCESS START-UP RESET The control registers listed in Table 7 provide a variety of user configuration options. The SPI provides access to these registers, one byte at a time, using the bit assignments shown in Figure 13. Each register has 16 bits, wherein Bits[7:0] represent the lower address, and Bits[15:8] represent the upper address. Figure 16 provides an example of writing 0x03 to Address 0x32 (GPIO_CTRL[7:0], see Table 23). DIN MANUAL FLASH BACKUP Figure 16. SPI Sequence for Setting the Decimate Rate to 8 (DIN = 0xB203) Rev. B | Page 13 of 24 Figure 17. SRAM and Flash Memory Diagram 11117-018 Table 15. AUX_ADC Bits (Base Address = 0x0A) ADIS16266 Data Sheet DIGITAL SIGNAL PROCESSING Figure 19 provides a signal processing diagram that describes all of the user-configurable options, which influence sample rate and the frequency response. Using the factory default settings for the SMPL_PRD and SENS_AVG registers, the effective sensor bandwidth is 360 Hz. response (see Figure 19). For example, set SENS_AVG[2:0] = 100 (DIN = 0xB804) to set each stage to 16 taps. When used with the default sample rate of 2429 SPS (no decimation), this reduces the bandwidth of the digital filter to approximately 49 Hz. The minimum setting for this filter is two taps per stage (SENS_AVG[2:0] 001). DECIMATION FILTER (UPDATE RATE) Table 18. SENS_AVG Bits (Base Address = 0x38) The internal sampling system produces new data in the output data registers at a rate of 2429 SPS. The SMPL_PRD register (see Table 17) provides the functional control for the decimation filter stage, which provides a user control input for reducing the update rate in the output registers. The decimation filter reduces the update rate, using an averaging filter with a decimated output. These bits provide a binomial control that divides the data rate by a factor of 2 every time this number increases by 1. For example, set SMPL_PRD[3:0] = 00100 (DIN = 0xB604) to set the decimation factor to 16. This reduces the update rate to 151.8 SPS and the bandwidth (-3 dB) to approximately 75 Hz. Bits [15:11] [10:8] [7:3] [2:0] 0 Table 17. SMPL_PRD Bits (Base Address = 0x36) -20 Description (Default = 0x0000) Not used Decimation setting (D), see Figure 19 -40 MAGNITUDE (dB) FREQUENCY RESPONSE Analog Filter -60 -80 -100 N=2 N=4 N = 16 N = 64 -120 -140 0.001 DYNAMIC RANGE The SENS_AVG[10:8] bits provide three dynamic range settings for this gyroscope. The lower dynamic range settings (3500/sec and 7000/sec) limit the minimum filter tap sizes to maintain resolution. For example, set SENS_AVG[10:8] = 010 (DIN = 0xB902) for a measurement range of 7000/sec. Because this setting can influence the filter settings, program SENS_AVG[10:8] and then SENS_AVG[2:0] if more filtering is required. Digital Filtering A programmable low-pass filter provides additional noise reduction on the inertial sensor outputs. This filter contains two cascaded averaging filters that provide a Bartlett window, FIR filter BARTLETT WINDOW FIR FILTER 1 NB ADC GYROSCOPES LOW-PASS, TWO-POLE (1.6kHz, 1.6kHz) 1 Figure 18. Digital Filter Frequency, Bartlett Window FIR Filter (Phase = N Samples) For example, adding a 1000 pF capacitor reduces this pole to approximately 567 Hz. ANALOG LOW-PASS FILTER 1200Hz 0.1 FREQUENCY (f/fS) 1 fC 2 180000 C 560 pF MEMS SENSOR 0.01 11117-019 Prior to the analog-to-digital conversion stage, the ADIS16266 has a two-pole analog filter, with both poles located at approximately 1.6 kHz. The RATE and FILT pins provide access to the amplifier feedback path on one of these filters. This provides an opportunity to reduce the cut-off frequency associated with this filter pole, according to the following relationship. CLOCK NB x(n) n=1 1 NB NB x(n) n=1 B = SENS_AVG[2:0] NB = 2B NB = NUMBER OF TAPS (PER STAGE) Figure 19. Signal Processing Diagram Rev. B | Page 14 of 24 AVERAGE/ DECIMATION FILTER 1 ND ND /ND x(n) n=1 D = SMPL_PRD[3:0] ND = 2D ND = NUMBER OF TAPS 11117-020 Bits [15:4] [3:0] Description (Default = 0x0401) Not used. Measurement range (sensitivity) selection. 100 = 14,000/sec, filter taps 2 (Bits[2:0] 0x01). 010 = 7000/sec, filter taps 4 (Bits[2:0] 0x02). 001 = 3500/sec, filter taps 16 (Bits[2:0] 0x04). Not used. Number of taps in each stage; value of m in N = 2m. Data Sheet ADIS16266 CALIBRATION The GYRO_OFF and GYRO_SCALE registers provide user controls for making in-system adjustments to offset and the scale factor. Bits [15:12] [11:0] TO OUTPUT REGISTERS GYRO_OFF GYRO_SCALE 11117-021 FROM INTERNAL PROCESSING Table 20. GYRO_SCALE Bits (Base Address = 0x16) Figure 20. User Calibration Registers Table 19. GYRO_OFF Bits (Base Address = 0x14) Bits [15:12] [11:0] Description (Default = 0x0000) Not used. Offset adjustment factor, twos complement format, 1.04/sec per LSB. Examples: 0x000: add 0/sec to gyroscope data. 0x001: add 1.04/sec to gyroscope data. 0x0AA: add 176.8/sec to gyroscope data. 0xF0F: subtract 250.64/sec from gyroscope data. 0xFFF: subtract 1.04/sec from gyroscope data. Rev. B | Page 15 of 24 Description (Default = 0x0800) Not used. Scale adjustment factor, offset binary format, 0.00048828/LSB. Examples: 0x000: multiply output by 0. 0x7F0: multiply gyroscope data by 0.99218. 0x800: multiply output by 1. 0x8A0: multiply output by 1.078122. 0xFFF: multiply output by 1.9995. ADIS16266 Data Sheet SYSTEM TOOLS Global Commands Data Ready Input/Output Indicator The GLOB_CMD register provides trigger bits for several functions. Setting the assigned bit to 1 starts each operation, which returns the bit to 0 after completion. For example, set GLOB_CMD[7] = 1 (DIN = 0xBE80) to execute a software reset, which stops the sensor operation and runs the device through its start-up sequence. This sequence includes loading the control registers with the contents of their respective flash memory locations prior to producing new data. The MSC_CTRL[2:0] bits configure one of the digital input/output lines as a data ready signal for driving an interrupt. For example, set MSC_CTRL[2:0] = 100 (DIN = 0xB404) to configure DIO1 as a negative-pulse data ready signal. The pulse width is between 100 s and 200 s over all conditions. Table 21. GLOB_CMD Bits (Base Address = 0x3E) Bits [15:8] 7 6:4 3 2 1 0 Description Not used. Software reset command. Not used. Flash update command. Auxiliary DAC data latch. Factory calibration restore command. Autonull command. Table 24. MSC_CTRL Bits (Base Address = 0x34) Bits [15:12] 11 10 9 8 Power Management 7:3 2 Use SLP_CNT[7:0] to put the device into sleep mode for a specified period. For example, SLP_CNT[7:0] = 0x64 (DIN = 0xBA64) puts the ADIS16266 to sleep for 50 seconds. 1 0 Table 22. SLP_CNT Bits (Base Address = 0x3A) Bits [15:8] [7:0] Description Not used. Programmable sleep time bits, 0.5 sec/LSB. Auxiliary DAC General-Purpose Input/Output DIO1 and DIO2 are configurable, general-purpose input/output lines that serve multiple purposes according to the following control register priority: MSC_CTRL, ALM_CTRL, and GPIO_CTRL. For example, set GPIO_CTRL = 0x0202 (DIN = 0xB302, and then 0xB202) to configure DIO1 as an input and DIO2 as an output that is set high. Table 23. GPIO_CTRL Bits (Base Address = 0x32) Bits [15:10] 9 8 [7:2] 1 0 Description (Default = 0x0006) Not used. Memory test (cleared upon completion). 1 = enabled, 0 = disabled. Internal self-test enable (cleared upon completion). 1 = enabled, 0 = disabled. Manual self-test, negative stimulus. 1 = enabled, 0 = disabled. Manual self-test, positive stimulus. 1 = enabled, 0 = disabled. Not used. Data ready enable. 1 = enabled, 0 = disabled. Data ready polarity. 1 = active high, 0 = active low. Data ready line select. 1 = DIO2, 0 = DIO1. Description (Default = 0x0000) Not used. General-Purpose input/output Line 2 (DIO2) data level. General-Purpose input/output Line 1 (DIO1) data level. Not used. General-Purpose input/output Line 2 (DIO2) direction control. 1 = output, 0 = input. General-Purpose input/output Line 1 (DIO1) direction control. 1 = output, 0 = input. The 12-bit AUX_DAC line can drive its output to within 5 mV of the ground reference when it is not sinking current. As the output approaches 0 V, the linearity begins to degrade (approximately 100 LSB starting point). As the sink current increases, the nonlinear range increases. The DAC latch command (GLOB_CMD[2]) moves the values of the AUX_DAC register into the internal DAC control register, enabling both bytes to take effect at the same time. Table 25. AUX_DAC Bits (Base Address = 0x30) Bits [15:12] [11:0] Description (Default = 0x0000) Not used. Data bits, scale factor = 0.6105 mV/code. Offset binary format, 0 V = 0 codes. Table 26. Setting AUX_DAC = 2 V DIN 0xB0CC 0xB10C 0xBE04 Rev. B | Page 16 of 24 Description AUX_DAC[7:0] = 0xCC (204 LSB). AUX_DAC[15:8] = 0x0C (3072 LSB). GLOB_CMD[2] = 1. Latch AUX_DAC values into the internal DAC control register which causes the output voltage to settle at a value of 2 V. Data Sheet ADIS16266 Memory Management The FLASH_CNT register (see Table 27) tracks the number of write cycles for the flash memory to help manage the total cycles against the endurance ratings in Table 1. Zero motion provides results that are more reliable. The settings in Table 28 are flexible and allow for optimization around speed and noise influence. For example, using fewer filtering taps decreases delay times but increases the potential for noise influence. Memory Test Table 27. FLASH_CNT Bits (Base Address = 0x00) DIAGNOSTICS Setting MSC_CTRL[11] = 1 (DIN = 0xB508) performs a checksum comparison between the flash memory and SRAM to help verify memory integrity. The pass/fail result is loaded into the DIAG_STAT[6] register. Self-Test Status The self-test function allows the user to verify the mechanical integrity of each MEMS sensor. It applies an electrostatic force to each sensor element, which results in mechanical displacement that simulates a response to actual motion. Table 1 lists the expected response for the sensor, which provides pass/fail criteria. The error flags provide indicator functions for common system level issues. All of the flags are cleared (set to 0) after each DIAG_STAT register read cycle. If an error condition remains, the error flag returns to 1 during the next sample cycle. DIAG_STAT[1:0] does not require a read of this register to return to 0. When the power supply voltage goes back into range, these two flags clear automatically. Bits [15:0] Description Flash update counter Set MSC_CTRL[10] = 1 (DIN = 0xB504) to run the internal self-test routine, which exercises the inertial sensor, measures the response, makes a pass/fail decision, reports the decision to the error flags in the DIAG_STAT register, and then restores normal operation. MSC_CTRL[10] resets itself to 0 after completing the routine. The MSC_CTRL[9:8] bits provide manual control of the self-test function for investigation of potential failures. Table 28 outlines an example test flow for using this option to verify the gyroscope function. Table 28. Manual Self-Test Example Sequence DIN 0xB601 0xB904 0xB802 0x0400 0xB502 0x0400 0xB501 0x0400 0xB500 Description SMPL_PRD[7:0] = 0x01, sample rate = 2429 SPS. SENS_AVG[15:8] = 0x04, range = 14000/sec. SENS_AVG[7:0] = 0x02, four-tap averaging filter. Delay = 50 ms. Read GYRO_OUT. MSC_CTRL[9:8] = 10, gyroscope negative self-test. Delay = 50 ms. Read GYRO_OUT. Determines whether the bias in the gyroscope output changed according to the self-test response specified in Table 1. MSC_CTRL[9:8] = 01, gyroscope positive self-test. Delay = 50 ms. Read GYRO_OUT. Determines whether the bias in the gyroscope output changed according to the self-test response specified in Table 1. MSC_CTRL[15:8] = 0x00. Table 29. DIAG_STAT Bits (Base Address = 0x3C) Bits [15:10] 9 8 7 6 5 4 3 2 1 0 Rev. B | Page 17 of 24 Description Not used. Alarm 2 status (1 = active, 0 = inactive). Alarm 1 status (1 = active, 0 = inactive). Not used. Flash test, checksum flag (1 = fail, 0 = pass). Self-test diagnostic error flag (1 = fail, 0 = pass). Sensor overrange (1 = fail, 0 = pass). SPI communication failure (1 = fail, 0 = pass). Flash update failure (1 = fail, 0 = pass). Power supply > 5.25 V. 1 = power supply > 5.25 V, 0 = power supply 5.25 V. Power supply < 4.75 V. 1 = power supply < 4.75 V, 0 = power supply 4.75 V. ADIS16266 Data Sheet ALARMS Table 34. ALM_CTRL Bits (Base Address = 0x28) Alarm Registers The alarm function provides monitoring for two independent conditions. The ALM_CTRL register provides control inputs for data source selection, data filtering (prior to comparison), static comparison, dynamic rate-of-change comparison, and output indicator configurations. The ALM_MAGx registers establish the trigger threshold and polarity configurations. Table 35 gives an example of how to configure a static alarm. The ALM_SMPLx registers provide the numbers of samples to use in the dynamic rate-of-change configuration. The period equals the number in the ALM_SMPLx register multiplied by the sample period time. See Table 36 for an example of how to configure the sensor for this type of function. Table 30. ALM_MAG1 Bits (Base Address = 0x20) Bits 15 14 [13:0] Description (Default = 0x0000) Comparison polarity (1 = greater than, 0 = less than). Not used. Data bits that match the format of the trigger source selection. Table 31. ALM_MAG2 Bits (Base Address = 0x22) Bits 15 14 [13:0] Description (Default = 0x0000) Comparison polarity (1 = greater than, 0 = less than). Not used. Data bits that match the format of the trigger source selection. Bits 15 [14:12] 11 [10:8] [7:5] 4 3 2 1 0 Table 35. Alarm Configuration Example 1 DIN 0xA922, 0xA817 Table 32. ALM_SMPL1 Bits (Base Address = 0x24) Bits [15:8] [7:0] Description (Default = 0x0000) Not used. Data bits: number of samples (both 0x00 and 0x01 = 1). Table 33. ALM_SMPL2 Bits (Base Address = 0x26) Bits [15:8] [7:0] Description (Default = 0x0000) Not used. Data bits: number of samples (both 0x00 and 0x01 = 1). Description (Default = 0x0000) Dynamic rate-of-change enable for Alarm 2 (1 = rate of change, 0 = static level). Alarm 2 source selection. 000 = disable. 001 = power supply output. 010 = gyroscope output. 011 = not used. 100 = not used. 101 = auxiliary ADC input. 110 = temperature output. 111 = not used. Rate-of-change enable for Alarm 1 (1 = dynamic rate of change, 0 = static level). Alarm 1 source selection (same as for Alarm 2). Not used. Comparison data filter setting (1 = filtered data, 0 = unfiltered data). Not used. Alarm output enable (1 = enabled, 0 = disabled). Alarm output polarity (1 = active high, 0 = active low). Alarm output line select (1 = DIO2, 0 = DIO1). 0xA183, 0xA0E8 0xA338, 0xA230 Rev. B | Page 18 of 24 Description ALM_CTRL = 0x2217. Alarm 1 input = GYRO_OUT. Alarm 2 input = GYRO_OUT. Static level comparison, filtered data. DIO2 output indicator, positive polarity. ALM_MAG1 = 0x83E8. Alarm 1 is true if GYRO_OUT > +4170/sec. ALM_MAG2 = 0x3830. Alarm 2 is true if GYRO_OUT < -8340/sec. Data Sheet ADIS16266 Table 36. Alarm Configuration Example 2 PRODUCT IDENTIFICATION DIN 0xA9AA, 0xA804 Table 37 provides a summary of the registers that identify the product: PROD_ID, which identifies the product type; LOT_ID1 and LOT_ID2, the 32-bit lot identification code; and SERIAL_NUM, which displays the 16-bit serial number. All four registers are two bytes in length. 0xB600 0xA4FF 0xA6FF 0xA181, 0xA000 0xA300, 0xA20A Description ALM_CTRL = 0xAA04. Alarm 1 input = GYRO_OUT. Alarm 2 input = GYRO_OUT. Dynamic rate-of-change comparison, unfiltered data. DIO1 output indicator, negative polarity. SMPL_PRD = 0x0000. Sample rate = 2429 SPS. ALM_SMPL1[7:0] = 0x00FF. Alarm 1 dynamic rate-of-change period = 105 ms. ALM_SMPL2[7:0] = 0x00FF. Alarm 2 dynamic rate-of-change period = 105 ms. ALM_MAG1 = 0x8100. Alarm 1 is true if GYRO_OUT changes more than 1067.5/sec over a period of 105 ms. ALM_MAG2 = 0x000A. Alarm 2 is true if GYRO_OUT changes less than 41.7/sec over a period of 105 ms. Table 37. Identification Registers Register Name LOT_ID1 LOT_ID2 PROD_ID Address 0x52 0x54 0x56 SERIAL_NUM 0x58 Rev. B | Page 19 of 24 Description Lot Identification Code 1 Lot Identification Code 2 Product identification = 0x3F8A (0x3F8A = 16,266 decimal) Serial number ADIS16266 Data Sheet APPLICATIONS INFORMATION ASSEMBLY BIAS OPTIMIZATION When developing a process flow for installing ADIS16266 devices on printed circuit boards (PCBs), see the IPC/JEDEC J-STD-020C standard document for reflow temperature profile and processing information. The ADIS16266 can use the Sn-Pb eutectic process or the Pb-free eutectic process from this standard. See IPC/JEDEC J-STD-033 for moisture sensitivity level (MSL) handling requirements. The MSL rating for these devices is marked on the antistatic bags, which protect these devices from electrostatic discharge (ESD) during shipping and handling. Use the following steps to fine tune the bias to an accuracy that approaches the in-run bias stability, 0.129/sec (1 ): Prior to assembly, review the process flow for information about introducing shock levels that exceed the absolute maximum ratings for the ADIS16266. PCB separation and ultrasonic cleaning processes can introduce high levels of shock and damage the MEMS element. Bowing or flexing the PCB after solder reflow can also place large peeling stress on the pad structure and can damage the device. If this is unavoidable, consider using an underfill material to help distribute these forces across the bottom of the package. Figure 21 provides a PCB pad design example for this package style. 1. 2. 3. 4. 5. 6. 7. 8. 9. Alternatively, setting GLOB_CMD[0] = 1 (DIN = 0xBE01) provides a single sample, bias correction. The Allan variance curve (see Figure 6) provides a trade-off relationship between accuracy and averaging time. For example, an average time of 1 second produces an accuracy of approximately 0.358/sec (1 ). 5.0865 8x 3.800 8x 0.773 16x 10.173 2x 7.600 4x 11mm x 11mm STACKED LGA PACKAGE 11117-022 0.500 20x 1.127 20x Apply 5 V and allow enough time to start up. Set SENS_AVG[10:8] = 001 (DIN = 0xB901). Collect GYRO_OUT data for 30 seconds at a sample rate of 2429 SPS. Average data record. Round to the nearest integer. Multiply by -1. Write the resulting number (from Step 6) to GYRO_OFF. Set GLOB_CMD[3] = 1 (DIN = 0xBE08). Wait for >50 ms and resume operation. Figure 21. Recommended Pad Layout (Units in Millimeters) Rev. B | Page 20 of 24 Data Sheet ADIS16266 1.050 INTERFACE PCB The pad pattern on these PCBs matches that shown in Figure 23. J1 and J2 are dual-row, 2 mm (pitch) connectors that work with a number of ribbon cable systems, including the TCSD-08-D-xx.00-01 series from Samtec. The schematic and connector pin assignments for the ADIS16266/PCBZ are shown in Figure 22. J1 1 2 3 4 7 1 4 2 7 8 3 18 19 13 SCLK VREF DOUT DIN 12 20 11 14 15 3 4 6 7 GND 8 VCC 10 9 16 17 DIO2 VCC 12 13 2 x 0.000 J2 1 GND DIO1 RATE 14 6 5 11 12 FILT 15 C2 16 C2 J2 4 x O0.087 M2 x 0.4 C1 11117-023 C1 U1 5 ADIS16266 9 10 J1 2 AUX DAC CS 5 6 AUX ADC RST 2 x 0.925 Figure 22. Electrical Schematic Rev. B | Page 21 of 24 iSensor(R) GS10265RA 0.150 Figure 23. PCB Assembly View and Dimensions 11117-024 The ADIS16266/PCBZ includes one ADIS16266BCCZ IC on a 1.2 inch x 1.3 inch PCB. The interface PCB simplifies the IC connection of these devices to an existing processor system. The four mounting holes accommodate either M2 (2 mm) or 2-56 machine screws. These boards are made of IS410 material and are 0.063 inches thick. The second level assembly uses a SAC305compatible solder composition, which has a presolder reflow thickness of approximately 0.005 inches. ADIS16266 Data Sheet OUTLINE DIMENSIONS 7.600 BSC (4x) 3.800 BSC (8x) 11.15 MAX 16 15 11.00 TYP 1.000 BSC (20x) 20 1 10.173 BSC (2x) 0.900 BSC (16x) 11 10 0.200 MIN (ALL SIDES) TOP VIEW PIN 1 INDICATOR 6 5 BOTTOM VIEW 0.373 BSC (20x) 7.00 TYP 022007-B 5.50 MAX SIDE VIEW Figure 24. 20-Terminal Stacked Land Grid Array [LGA] (CC-20-1) Dimensions shown in millimeters ORDERING GUIDE Model 1 ADIS16266BCCZ ADIS16266/PCBZ 1 Temperature Range -40C to +105C Package Description 20-Terminal Stacked Land Grid Array [LGA] Evaluation Board Z = RoHS Compliant Part. Rev. B | Page 22 of 24 Package Option CC-20-1 Data Sheet ADIS16266 NOTES Rev. B | Page 23 of 24 ADIS16266 Data Sheet NOTES (c)2012-2015 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D11117-0-7/15(B) Rev. B | Page 24 of 24 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Analog Devices Inc.: ADIS16266/PCBZ ADIS16266BCCZ