19-3488; Rev 2; 1/07 KIT ATION EVALU E L B A IL AVA Multichannel, True-Differential, Serial, 14-Bit ADCs Features 8-Channel Single-Ended or 4-Channel Differential Inputs (MAX1148/MAX1149) 4-Channel Single-Ended or 2-Channel Differential Inputs (MAX1146/MAX1147) Internal Multiplexer and T/H Single-Supply Operation 4.75V to 5.25V Supply (MAX1146/MAX1148) 2.7V to 3.6V Supply (MAX1147/MAX1149) Internal Reference +4.096V (MAX1146/MAX1148) +2.500V (MAX1147/MAX1149) 116ksps Sampling Rate Low Power 1.1mA (116ksps) 120A (10ksps) 12A (1ksps) 300nA (Power-Down Mode) SPI-/QSPI-/MICROWIRE Compatible 20-Pin TSSOP Applications Portable Data Logging Data Acquisition Pin Configurations appear at end of data sheet. Medical Instruments Battery-Powered Instruments SPI/QSPI are trademarks of Motorola, Inc. MICROWIRE is a trademark of National Semiconductor Corp. Process Control Ordering Information/Selector Guide PART TEMP RANGE PINPACKAGE INL (LSB) INPUT CHANNELS INTERNAL REFERENCE (V) PKG CODE MAX1146BCUP 0C to +70C 20 TSSOP 2 4 +4.096 U20-3 MAX1146BEUP -40C to +85C 20 TSSOP 2 4 +4.096 U20-3 MAX1147BCUP 0C to +70C 20 TSSOP 2 4 +2.500 U20-3 MAX1147BEUP -40C to +85C 20 TSSOP 2 4 +2.500 U20-3 MAX1148BCUP 0C to +70C 20 TSSOP 2 8 +4.096 U20-3 MAX1148BEUP -40C to +85C 20 TSSOP 2 8 +4.096 U20-3 MAX1149BCUP 0C to +70C 20 TSSOP 2 8 +2.500 U20-3 MAX1149BEUP -40C to +85C 20 TSSOP 2 8 +2.500 U20-3 ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim's website at www.maxim-ic.com. 1 MAX1146-MAX1149 General Description The MAX1146-MAX1149 low-power, 14-bit, multichannel, analog-to-digital converters (ADCs) feature an internal track/hold (T/H), voltage reference, and clock. The MAX1146/MAX1148 operate from a single +4.75V to +5.25V supply, and the MAX1147/MAX1149 operate from a single +2.7V to +3.6V supply. All analog inputs are software configurable for unipolar/bipolar and single-ended/differential operation. The 4-wire serial interface connects directly to SPITM/QSPITM/MICROWIRETM devices without external logic. The serial strobe output (SSTRB) allows convenient connection to digital signal processors. The MAX1146-MAX1149 use an internal clock or an external serial-interface clock to perform successive-approximation analog-to-digital conversions. The MAX1146/MAX1148 include an internal +4.096V reference, while the MAX1147/MAX1149 include an internal +2.500V reference. All devices accept an external reference from 1.5V to VDD. The MAX1146-MAX1149 provide a hardware shutdown and two software power-down modes. Using the software power-down modes allows the devices to be powered down between conversions. When powered down, accessing the serial interface automatically powers up the devices. The quick turn-on time allows power-down between all conversions. This technique reduces supply current to under 120A for quick turn-on. The MAX1146-MAX1149 are available in a 20-pin TSSOP package. MAX1146-MAX1149 Multichannel, True-Differential, Serial, 14-Bit ADCs ABSOLUTE MAXIMUM RATINGS VDD to AGND, DGND ............................................-0.3V to +6.0V AGND to DGND.....................................................-0.3V to +0.3V CH0-CH7, COM to AGND..........................-0.3V to (VDD + 0.3V) REF, REFADJ to AGND ..............................-0.3V to (VDD + 0.3V) Digital Inputs to DGND...............................-0.3V to (VDD + 0.3V) Digital Outputs to DGND ............................-0.3V to (VDD + 0.3V) Digital Output Sink Current .................................................25mA Continuous Power Dissipation (TA = +70C) 20 TSSOP (derate 10.9mW/C above +70C) .............879mW Operating Temperature Ranges MAX114_ BC_ _ ..................................................0C to +70C MAX114_ BE_ _ ...............................................-40C to +85C Storage Temperature Range .............................-60C to +150C Lead Temperature (soldering, 10s) .................................+300C Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (VDD = 5V (MAX1146/MAX1148), VDD = 3.3V (MAX1147/MAX1149), SHDN = VDD, VCOM = 0, fSCLK = 2.1MHz, external clock (50% duty cycle), 18 clocks/conversion (116ksps), VREFADJ = VDD, CREF = 2.2F, external +4.096V reference at REF (MAX1146/ MAX1148), external 2.500V reference at REF (MAX1147/MAX1149), TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS 0.7 2 LSB 0.5 +1.5 LSB DC ACCURACY (Note 1) Resolution 14 Relative Accuracy (Note 2) INL Differential Nonlinearity DNL No missing codes over temperature -1.0 Bits Offset Error 10 Offset Temperature Coefficient 0.3 Gain Error (Note 3) LSB ppm/C 20 Gain Temperature Coefficient LSB 0.8 ppm/C Channel-to-Channel Offset Matching 1 LSB Channel-to-Channel Gain Matching 1 LSB DYNAMIC SPECIFICATIONS (1kHz sine-wave input, 2.5VP-P, full-scale analog input, 116ksps, 2.1MHz external clock) Signal-to-Noise Plus Distortion Ratio SINAD Total Harmonic Distortion THD Spurious-Free Dynamic Range SFDR Channel-to-Channel Crosstalk 2 77 Up to the 5th harmonic 81 -96 84 dB -88 dB 98 dB (Note 4) -85 dB Small-Signal Bandwidth SSBW -3dB point 3.0 MHz Full-Power Bandwidth CONVERSION RATE FPBW SINAD > 68dB 2.0 MHz Conversion Time (Note 5) tCONV External clock, 2.1MHz 15 SCLK cycles Internal clock 7.2 6 _______________________________________________________________________________________ 8 s Multichannel, True-Differential, Serial, 14-Bit ADCs (VDD = 5V (MAX1146/MAX1148), VDD = 3.3V (MAX1147/MAX1149), SHDN = VDD, VCOM = 0, fSCLK = 2.1MHz, external clock (50% duty cycle), 18 clocks/conversion (116ksps), VREFADJ = VDD, CREF = 2.2F, external +4.096V reference at REF (MAX1146/ MAX1148), external 2.500V reference at REF (MAX1147/MAX1149), TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) PARAMETER Throughput Rate SYMBOL fSAMPLE T/H Acquisition Time Internal clock mode, fSCLK = 2.1MHz tAD Aperture Jitter tAJ fSCLK MIN TYP 18 clocks/conversion MAX 51.5 External clock mode, 18 clocks/conversion fSCLK = 2.1MHz 24 clocks/conversion 116.66 s 20 ns <50 ps External clock mode 0.1 2.1 Internal clock mode 0 2.1 Internal Clock Frequency ANALOG INPUTS (CH0-CH7, COM) 2.1 Unipolar, COM = 0 Bipolar, COM = VREF / 2, single-ended Multiplexer Leakage Current On/off-leakage current, VCH_ = 0 to VDD ksps 87.50 1.4 Input Voltage Range, SingleEnded and Differential (Note 6) UNITS 60.3 24 clocks/conversion tACQ Aperture Delay Serial Clock Frequency CONDITIONS 0 Input Capacitance MHz VREF VREF / 2 0.01 MHz 1 18 V A pF INTERNAL REFERENCE (CREF = 2.2F, CREFADJ = 0.01F) REF Output Voltage VREF REF Short-Circuit Current VREF Tempco (Note 7) Load Regulation IREFSC MAX1147/MAX1149, TA = +25C 2.480 2.500 2.520 MAX1146/MAX1148, TA = +25C 4.076 4.096 4.116 REF = DGND 20 MAX114_ BC _ _ 30 50 MAX114_ BE _ _ 40 60 0 to 0.2mA output load (Note 8) 2.0 Capacitive Bypass at REF Capacitive Bypass at REFADJ Reference Buffer Voltage Gain ppm/C mV 2 F F REFADJ Input Range REFADJ Logic High mA 0.01 REFADJ Output Voltage Pull REFADJ high to disable the internal bandgap reference and reference buffer V 1.250 V 18 mV VDD 0.25V V MAX1147/MAX1149 2.000 MAX1146/MAX1148 3.277 V/V _______________________________________________________________________________________ 3 MAX1146-MAX1149 ELECTRICAL CHARACTERISTICS (continued) MAX1146-MAX1149 Multichannel, True-Differential, Serial, 14-Bit ADCs ELECTRICAL CHARACTERISTICS (continued) (VDD = 5V (MAX1146/MAX1148), VDD = 3.3V (MAX1147/MAX1149), SHDN = VDD, VCOM = 0, fSCLK = 2.1MHz, external clock (50% duty cycle), 18 clocks/conversion (116ksps), VREFADJ = VDD, CREF = 2.2F, external +4.096V reference at REF (MAX1146/ MAX1148), external 2.500V reference at REF (MAX1147/MAX1149), TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS VDD + 50mV V EXTERNAL REFERENCE AT REF REF Input Voltage Range VREF REF Input Current IREF 1.5 Shutdown REF Input Resistance 6 125 450 0.01 10 8 A k DIGITAL INPUTS (DIN, SCLK, CS, SHDN) Input High Voltage VIH Input Low Voltage VIL Input Hysteresis VDD < 3.6V 2.0 VDD > 3.6V 3.0 VHYST Input Leakage IIN Input Capacitance CIN V 0.8 V 1 A 0.2 V 10 pF DIGITAL OUTPUT (DOUT, SSTRB) Output-Voltage Low VOL ISINK = 2mA Output-Voltage High VOH ISOURCE = 2mA Tri-State Leakage Current Tri-State Output Capacitance IL CS = VDD COUT CS = VDD 0.4 V 10 A VDD - 0.5 V 10 pF POWER REQUIREMENTS Positive Supply Voltage Supply Current (Note 8) VDD IDD MAX1147/MAX1149 2.7 3.6 MAX1146/MAX1148 4.75 5.25 Normal operation, fullscale input Fast power-down Shutdown Supply Current (Note 8) Power-Supply Rejection (Note 9) 4 PSR External reference 116ksps 10ksps 1ksps Internal reference at 116ksps 1.1 0.12 0.012 1.5 1.9 2.4 mA mA 120 Full power-down 0.3 SHDN = DGND 0.3 External reference V 0.2 _______________________________________________________________________________________ A 10 mV Multichannel, True-Differential, Serial, 14-Bit ADCs (VDD = 4.75V to 5.25V (MAX1146/MAX1148), VDD = 2.7V to 3.6V (MAX1147/MAX1149), SHDN = VDD, VCOM = 0, fSCLK = 2.1MHz, external clock (50% duty cycle), 18 clocks/conversion (116ksps), VREFADJ = VDD, CREF = 2.2F, external +4.096V reference at REF for the MAX1146/MAX1148, external 2.500V reference at REF for the MAX1147/MAX1149, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) (Figures 1, 2, and 3) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS DIN to SCLK Setup Time tDS 50 ns DIN to SCLK Hold Time tDH 0 ns SCLK Fall to Output Data Valid tDOV CLOAD = 50pF CS Fall to DOUT Enable tDOE CS Rise to DOUT Disable tDOD SHDN Rise CS Fall to SCLK Rise Time tCSS 50 ns SHDN Rise CS Fall to SCLK Rise Hold Time tCSH 50 ns SCLK Clock Frequency fSCLK SCLK Pulse-Width High 10 80 ns CLOAD = 50pF 120 ns CLOAD = 50pF 120 ns External clock mode 0.1 2.1 Internal clock mode 0 2.1 tCH Internal clock mode 100 SCLK Pulse-Width Low tCL Internal clock mode 100 CS Fall to SSTRB Output Enable tSTE External clock mode only 120 ns CS Rise to SSTRB Output Disable tSTD External clock mode only 120 ns SSTRB Rise to SCLK Rise tSCK Internal clock mode only SCLK Fall to SSTRB Edge tSCST 80 ns CS Pulse Width tCSW ns ns 0 100 MHz ns ns Note 1: Tested at VDD = 3.0V (MAX1147/MAX1149) or 5.0V(MAX1146/MAX1148); VCOM = 0; unipolar single-ended input mode. Note 2: Relative accuracy is the deviation of the analog value at any code from its theoretical value after the full-scale range has been calibrated. Note 3: Offset nulled. Measured with external reference. Note 4: "On" channel grounded; full-scale 1kHz sine wave applied to all "off" channels. Note 5: Conversion time defined as the number of clock cycles multiplied by the clock period; clock has 50% duty cycle. (See Figures 8-11.) Note 6: The common-mode range for the analog inputs is from AGND to VDD. Note 7: Digital inputs equal VDD or DGND. Note 8: External load should not change during conversion for specified accuracy. Note 9: Measured as (VFS x 3.6V) - (VFS x 2.7V) for the MAX1147/MAX1149 and (VFS x 5.25V) - (VFS x 4.75V) for the MAX1146/MAX1148. VDD = 3.6V to 2.7V for MAX1147/MAX1149 and VDD = 5.25V to 4.75V for the MAX1146/MAX1148. _______________________________________________________________________________________ 5 MAX1146-MAX1149 TIMING CHARACTERISTICS MAX1146-MAX1149 Multichannel, True-Differential, Serial, 14-Bit ADCs VDD VDD 6k DOUT 6k DOUT CLOAD 50pF 6k DGND DGND a) HIGH-Z TO VOH AND VOL TO VOH DOUT DOUT CLOAD 50pF 6k DGND DGND b) HIGH-Z TO VOL AND VOH TO VOL CLOAD 50pF CLOAD 50pF DGND DGND a) VOH TO HIGH-Z Figure 1. Load Circuits for Enable Time b) VOL TO HIGH-Z Figure 2. Load Circuits for Disable Time CS tCH tCSS tCSW tCL tCSH SCLK 1 1 8 START SEL2 SEL1 SEL0 SGL/DIF UNI/BIP tDOE DOUT HIGH-Z SSTRB (EXTERNAL CLOCK MODE) HIGH-Z 24 tDH tDS DIN 9 tSCK fSCLK PD1 PD0 tACQ tDOD tDOV D13 D12 D11 D10 D2 D1 D0 tSCST tSTE tSTD HIGH-Z tSCST SSTRB (INTERNAL CLOCK MODE) Figure 3. Detailed Operating Characteristics 6 HIGH-Z _______________________________________________________________________________________ Multichannel, True-Differential, Serial, 14-Bit ADCs (VDD = +5.0V (MAX1146/MAX1148), VDD = +3.3V (MAX1147/MAX1149), SHDN = VDD, VCOM = 0, fSCLK = 2.1MHz, external clock (50% duty cycle), 18 clocks/conversion (116ksps), VREFADJ = VDD, external +4.096V reference at REF (MAX1146/MAX1148), external +2.500V reference at REF (MAX1147/MAX1149), CREF = 2.2F, CLOAD = 50pF, TA = +25C, unless otherwise noted.) 0.5 DNL (LSB) 0.5 0 0 -0.5 -0.5 -1.0 -1.0 -1.5 -1.5 1.8 MAX1146 toc03 1.0 INTERNAL REFERENCE 1.6 SUPPLY CURRENT (mA) 1.0 2.0 MAX1146 toc02 1.5 MAX1146 toc01 1.5 INL (LSB) SUPPLY CURRENT vs. SUPPLY VOLTAGE (MAX1147/MAX1149) DNL vs. OUTPUT CODE INL vs. OUTPUT CODE 1.4 1.2 EXTERNAL REFERENCE 1.0 0.8 0.6 0.4 0.2 0 4096 8192 12288 8192 12288 16384 2.7 3.0 3.6 3.3 OUTPUT CODE SUPPLY VOLTAGE (V) SUPPLY CURRENT vs. SUPPLY VOLTAGE (MAX1146/MAX1148) SHUTDOWN SUPPLY CURRENT vs. SUPPLY VOLTAGE (MAX1147/MAX1149) SHUTDOWN SUPPLY CURRENT vs. SUPPLY VOLTAGE (MAX1146/MAX1148) 1.2 EXTERNAL REFERENCE 1.0 0.8 0.6 0.4 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.2 0 0 MAX1146 toc06 1.6 0.45 SHUTDOWN SUPPLY CURRENT (A) 1.4 MAX1146 toc05 INTERNAL REFERENCE 1.6 1.8 SHUTDOWN SUPPLY CURRENT (A) MAX1146 toc04 1.8 0.40 0.35 0.30 0.25 0.20 0.15 0.10 0.05 0 4.75 4.85 4.95 5.05 5.15 4.75 4.80 4.85 4.90 4.95 5.00 5.05 5.10 5.15 5.20 5.25 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 SUPPLY VOLTAGE (V) SUPPLY VOLTAGE (V) SUPPLY VOLTAGE (V) SUPPLY CURRENT vs. CONVERSION RATE SUPPLY CURRENT vs. TEMPERATURE SHUTDOWN SUPPLY CURRENT vs. TEMPERATURE 800 600 FAST POWER-DOWN 400 MAX1146/MAX1148 INTERNAL REFERENCE MAX1147/MAX1149 INTERNAL REFERENCE 1.5 MAX1146/MAX1148 EXTERNAL REFERENCE 1.0 MAX1147/MAX1149 EXTERNAL REFERENCE 0.5 200 FULL POWER-DOWN 0 0.1 1 10 CONVERSION RATE (ksps) 100 1000 4.0 3.5 3.0 MAX1146/MAX1148 2.5 2.0 1.5 1.0 MAX1147/MAX1149 0.5 0 0 0.01 5.25 MAX1146 toc09 2.0 SUPPLY CURRENT (mA) 1000 4.5 SHUTDOWN SUPPLY CURRENT (A) 2.5 MAX1146 toc07 1200 MAX1146 toc08 SUPPLY CURRENT (mA) 4096 OUTPUT CODE 2.0 SUPPLY CURRENT (A) 0 0 16384 -40 -15 10 35 TEMPERATURE (C) 60 85 -40 -15 10 35 60 85 TEMPERATURE (C) _______________________________________________________________________________________ 7 MAX1146-MAX1149 Typical Operating Characteristics Typical Operating Characteristics (continued) (VDD = +5.0V (MAX1146/MAX1148), VDD = +3.3V (MAX1147/MAX1149), SHDN = VDD, VCOM = 0, fSCLK = 2.1MHz, external clock (50% duty cycle), 18 clocks/conversion (116ksps), VREFADJ = VDD, external +4.096V reference at REF (MAX1146/MAX1148), external +2.500V reference at REF (MAX1147/MAX1149), CREF = 2.2F, CLOAD = 50pF, TA = +25C, unless otherwise noted.) REFERENCE VOLTAGE vs. SUPPLY VOLTAGE (MAX1147/MAX1149) 2.5015 4.0970 4.0965 4.0960 4.0955 4.0950 2.5010 4.099 REFERENCE VOLTAGE (V) REFERENCE VOLTAGE (V) 4.0975 4.100 MAX1146 toc11 2.5020 MAX1146 toc10 4.0980 REFERENCE VOLTAGE vs. TEMPERATURE (MAX1146/MAX1148) 2.5005 2.5000 2.4995 2.4990 MAX1146 toc12 REFERENCE VOLTAGE vs. SUPPLY VOLTAGE (MAX1146/MAX1148) REFERENCE VOLTAGE (V) 4.098 4.097 4.096 4.095 4.094 4.093 4.092 4.0945 2.4985 4.0940 2.4980 4.95 5.05 4.090 2.7 5.25 5.15 3.0 3.6 3.3 10 2.502 2500 CREF = 4.7F CREFADJ = 0.01F 2000 DELAY (s) 2.501 2.500 35 REFERENCE BUFFER POWER-UP DELAY vs. TIME IN SHUTDOWN MAX1146 toc13 2.503 REFERENCE VOLTAGE (V) -15 TEMPERATURE (C) REFERENCE VOLTAGE vs. TEMPERATURE (MAX1147/MAX1149) 1500 1000 2.499 500 2.498 0 0.001 2.497 10 35 60 85 0.01 0.1 10 1 TEMPERATURE (C) TIME IN SHUTDOWN (s) FFT PLOT EFFECTIVE NUMBER OF BITS vs. FREQUENCY 20 10 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 fIN = 1kHz fSAMPLE = 116ksps VDD = 5V/3V 13.0 12.9 EFFECTIVE NUMBER OF BITS -15 MAX1146 toc15 -40 12.8 12.7 12.6 12.5 12.4 12.3 12.2 12.1 12.0 0 1000 2000 3000 4000 FREQUENCY (Hz) 8 -40 SUPPLY VOLTAGE (V) SUPPLY VOLTAGE (V) MAX1146 toc14 4.85 4.091 MAX1146 toc16 4.75 AMPLITUDE (dB) MAX1146-MAX1149 Multichannel, True-Differential, Serial, 14-Bit ADCs 5000 1 10 19 28 37 46 FREQUENCY (kHz) _______________________________________________________________________________________ 55 60 85 Multichannel, True-Differential, Serial, 14-Bit ADCs (VDD = +5.0V (MAX1146/MAX1148), VDD = +3.3V (MAX1147/MAX1149), SHDN = VDD, VCOM = 0, fSCLK = 2.1MHz, external clock (50% duty cycle), 18 clocks/conversion (116ksps), VREFADJ = VDD, external +4.096V reference at REF (MAX1146/MAX1148), external +2.500V reference at REF (MAX1147/MAX1149), CREF = 2.2F, CLOAD = 50pF, TA = +25C, unless otherwise noted.) OFFSET ERROR vs. SUPPLY VOLTAGE (MAX1146/MAX1148) OFFSET ERROR vs. SUPPLY VOLTAGE (MAX1147/MAX1149) 2 0 -2 MAX1146 toc18 -1 OFFSET ERROR (LSB) 4 OFFSET ERROR (LSB) 0 MAX1146 toc17 6 -2 -3 -4 -5 -6 -4 -7 -8 -6 3.0 3.3 4.95 5.05 5.15 SUPPLY VOLTAGE (V) GAIN ERROR vs. SUPPLY VOLTAGE (MAX1147/MAX1149) GAIN ERROR vs. SUPPLY VOLTAGE (MAX1146/MAX1148) 6 MAX1146 toc19 4 GAIN ERROR (LSB) 4 2 0 -2 -4 5.25 2 0 -2 -4 -6 -6 2.7 3.0 3.3 3.6 4.75 4.85 4.95 5.05 5.15 5.25 CHANNEL-TO-CHANNEL GAIN MATCHING vs. SUPPLY VOLTAGE (MAX1147/MAX1149) CHANNEL-TO-CHANNEL GAIN MATCHING vs. SUPPLY VOLTAGE (MAX1146/MAX1148) 6 6 4 GAIN MATCHING (LSB) 2 0 -2 -4 XMAX1146 toc22 SUPPLY VOLTAGE (V) MAX1146 toc21 SUPPLY VOLTAGE (V) 4 GAIN MATCHING (LSB) 4.85 SUPPLY VOLTAGE (V) 6 GAIN ERROR (LSB) 4.75 3.6 MAX1146 toc20 2.7 2 0 -2 -4 -6 -6 2.7 3.0 3.3 SUPPLY VOLTAGE (V) 3.6 4.75 4.85 4.95 5.05 5.15 5.25 SUPPLY VOLTAGE (V) _______________________________________________________________________________________ 9 MAX1146-MAX1149 Typical Operating Characteristics (continued) Typical Operating Characteristics (continued) (VDD = +5.0V (MAX1146/MAX1148), VDD = +3.3V (MAX1147/MAX1149), SHDN = VDD, VCOM = 0, fSCLK = 2.1MHz, external clock (50% duty cycle), 18 clocks/conversion (116ksps), VREFADJ = VDD, external +4.096V reference at REF (MAX1146/MAX1148), external +2.500V reference at REF (MAX1147/MAX1149), CREF = 2.2F, CLOAD = 50pF, TA = +25C, unless otherwise noted.) CHANNEL-TO-CHANNEL OFFSET MATCHING vs. SUPPLY VOLTAGE (MAX1147/MAX1149) CHANNEL-TO-CHANNEL GAIN MATCHING vs. TEMPERATURE 2 0 -2 2 0 -2 -4 -4 -6 -6 -40 -15 10 35 60 2.7 85 3.0 SUPPLY VOLTAGE (V) CHANNEL-TO-CHANNEL OFFSET MATCHING vs. SUPPLY VOLTAGE (MAX1146/MAX1148) CHANNEL-TO-CHANNEL OFFSET MATCHING vs. TEMPERATURE 4 OFFSET MATCHING (LSB) 2 0 -2 MAX1146 toc26 6 MAX1146 toc25 4 2 0 -2 -4 -4 -6 -6 4.75 4.85 4.95 5.05 5.15 -40 5.25 -15 10 35 60 85 TEMPERATURE (C) SUPPLY VOLTAGE (V) GAIN ERROR vs. TEMPERATURE OFFSET ERROR vs. TEMPERATURE 4 OFFSET ERROR (LSB) 4 2 0 -2 -4 MAX1146 toc28 6 MAX1146 toc27 6 2 0 -2 -4 -6 -6 -40 -15 10 35 TEMPERATURE (C) 10 3.6 3.3 TEMPERATURE (C) 6 OFFSET MATCHING (LSB) MAX1146 toc24 4 OFFSET MATCHING (LSB) 4 GAIN MATCHING (LSB) 6 MAX1146 toc23 6 GAIN ERROR (LSB) MAX1146-MAX1149 Multichannel, True-Differential, Serial, 14-Bit ADCs 60 85 -40 -15 10 35 60 TEMPERATURE (C) ______________________________________________________________________________________ 85 Multichannel, True-Differential, Serial, 14-Bit ADCs PIN MAX1148 MAX1146 MAX1149 MAX1147 NAME FUNCTION 1 1 CH0 2 2 CH1 3 3 CH2 4 4 CH3 5 -- CH4 6 -- CH5 7 -- CH6 8 -- CH7 9 9 COM Common Input. Negative analog input in single-ended mode. COM sets zero-code voltage in unipolar and bipolar mode. 10 10 SHDN Active-Low Shutdown Input. Pulling SHDN low shuts down the device reducing supply current to 0.2A. Driving shutdown high enables the devices. 11 11 REF 12 12 REFADJ 13 13 AGND Analog Ground 14 14 DGND Digital Ground 15 15 DOUT Serial Data Output. Data is clocked out at the falling edge of SCLK when CS is low. DOUT is high impedance when CS is high. Serial Strobe Output. In internal clock mode, SSTRB goes low when the ADC conversion begins, and goes high when the conversion is finished. In external clock mode, SSTRB pulses high for two clock periods before the MSB decision. SSTRB is high impedance when CS is high (external clock mode). Analog Inputs Reference-Buffer Output/ADC Reference Input. Reference voltage for analog-to-digital conversion. In internal reference mode, the MAX1146/MAX1148 VREF is +4.096V, and the MAX1147/MAX1149 VREF is +2.500V. Bandgap Reference Output and Reference Buffer Input. Bypass to AGND with a 0.01F capacitor. Connect REFADJ to VDD to disable the internal bandgap reference and referencebuffer amplifier. 16 16 SSTRB 17 17 DIN Serial Data Input. Data is clocked in at the rising edge of SCLK when CS is low. DIN is high impedance when CS is high. 18 18 CS Active-Low Chip Select. Data is not clocked into DIN unless CS is low. When CS is high, DOUT is high impedance. 19 19 SCLK Serial Clock Input. Clocks data in and out of the serial interface and sets the conversion speed in external clock mode. (Duty cycle must be 40% to 60%.) 20 20 VDD Positive Supply Voltage. Bypass to AGND with a 0.1F capacitor. -- 5-8 N.C. No Connection. Not internally connected. ______________________________________________________________________________________ 11 MAX1146-MAX1149 Pin Description MAX1146-MAX1149 Multichannel, True-Differential, Serial, 14-Bit ADCs Detailed Description The MAX1146-MAX1149 ADCs use a successiveapproximation conversion technique and input T/H circuitry to convert an analog signal to a 14-bit digital output. A flexible serial interface provides easy interface to microprocessors (Ps). Figure 4 shows the typical application circuit and Figure 5 shows a functional diagram of the MAX1148/MAX1149. True-Differential Analog Input and Track/Hold The MAX1146-MAX1149 analog input architecture contains an analog input multiplexer (MUX), two T/H capacitors, T/H switches, a comparator, and two switched capacitor digital-to-analog converters (DACs) (Figure 6). VDD 10 VDD CH0 CH1 CH2 ANALOG INPUTS 2.2F VDD 0.1F MAX1148 MAX1149 CH3 4.7F SHDN I/O CH4 SCLK SCK CH5 CS I/O CH6 DIN MOSI CH7 SSTRB REF DOUT COM AGND P I/O MISO REFADJ DGND VSS 0.01F Figure 4. Typical Application Circuit CS SCLK DIN INPUT SHIFT REGISTER SHDN CH0 CH1 CH2 CH3 CH4 CH5 CH6 CH7 ANALOG INPUT MUX INTERNAL CLOCK CONTROL LOGIC OUTPUT SHIFT REGISTER T/H IN DOUT SSTRB CLOCK SAR OUT ADC REF VDD COM +1.250V BANDGAP REFERENCE 20k REFADJ REF MAX1149 DGND AGND AV = 2.0V/V In single-ended mode, the analog input MUX connects IN+ to the selected input channel and IN- to COM. In differential mode, IN+ and IN- are connected to the selected analog input pairs such as CH0/CH1. Select the analog input channels according to Tables 1-5. The analog input multiplexer switches to the selected channel on the control byte's fifth SCLK falling edge. At this time, the T/H switches are in the track position and CT/H+ and CT/H- track the analog input signal. At the control byte's eighth SCLK falling edge, the MUX opens and the T/H switches move to the hold position, retaining the charge on CT/H+ and CT/H- as a sample of the input signal. See Figures 8-11 for input MUX and T/H switch positioning. During the conversion interval, the switched capacitive DAC adjusts to restore the comparator-input voltage to 0 within the limits of 14-bit resolution. This action requires 15 conversion clock cycles and is equivalent to transferring a charge of 18pF x (VIN+ - VIN-) from C T/H+ and C T/H- to the binary-weighted capacitive DAC, forming a digital representation of the analog input signal. After conversion, the T/H switches move from the hold position to the track position and the MUX switches back to the last specified position. In internal clock mode, the conversion is complete on the rising edge of SSTRB. In external clock mode, the conversion is complete on the eighteenth SCLK falling edge. The time required for the T/H to acquire an input signal is a function of the analog input source impedance. If the input signal source impedance is high, the acquisition time lengthens. The MAX1146-MAX1149 provide three SCLK cycles (tACQ) in which the T/H capacitance must acquire a charge representing the input signal, typically the last three SCLKs of the control word. The input source impedance (RSOURCE) should be minimized to allow the T/H capacitance to charge within this allotted time. tACQ = 11.5 x (RSOURCE + RIN) x CIN where RSOURCE is the analog input source impedance, RIN is 2.6k (which is the sum of the analog input MUX and T/H switch resistances), and CIN is 18pF (which is the sum of CT/H+, CT/H-, and input stray capacitance). To minimize sampling errors with higher source impedances, connect a 100pF capacitor from the analog input to AGND. This input capacitor reduces the input's AC impedance but forms an RC filter with the source impedance, limiting the analog input bandwidth. For larger source impedance, use a buffer amplifier such as the MAX4430 to maintain analog input signal integrity. Figure 5. Functional Diagram 12 ______________________________________________________________________________________ Multichannel, True-Differential, Serial, 14-Bit ADCs MAX1146-MAX1149 ANALOG INPUT MUX CH0 MAX1148 MAX1149 CH1 REF CH2 CT/H+ IN+ 14-BIT CAPACITIVE DAC CH3 TRACK CH4 HOLD HOLD HOLD CH5 TRACK TRACK 14-BIT CAPACITIVE DAC IN- CH6 CT/HCH7 REF COM Figure 6. Equivalent Input Circuit Input Bandwidth Quick Look The MAX1146-MAX1149 feature input tracking circuitry with a 3.0MHz small-signal bandwidth. The 3.0MHz input bandwidth makes it possible to digitize highspeed transient events and measure periodic signals with bandwidths exceeding the ADC's sampling rate by using undersampling techniques. To avoid high frequency signals being aliased into the frequency band of interest, anti-alias filtering is recommended. Use the circuit of Figure 7 to quickly evaluate the MAX1148/MAX1149. The MAX1148/MAX1149 require a control byte to be written to DIN using SCLK before each conversion. Connecting DIN to VDD and clocking SCLK feeds in a control byte of $FF HEX (see Table 1). Trigger single-ended unipolar conversions on CH7 in external clock mode without powering down between conversions. In external clock mode, the SSTRB output pulses high for two clock periods before the MSB of the 14-bit conversion result is shifted out of DOUT. Varying the analog input to CH7 alters the sequence of bits from DOUT. A total of 18 clock cycles are required per conversion (Figure 10). All transitions of the SSTRB and DOUT outputs occur on the falling edge of SCLK. Analog Input Protection Internal protection diodes clamp the analog input to VDD and AGND. These diodes allow the analog inputs to swing from (AGND - 0.3V) to (VDD + 0.3V) without causing damage to the device. For accurate conversions, the inputs must not go more than 50mV below AGND or above VDD. Note: If the analog input exceeds 50mV beyond the supply rails, limit the current to 2mA. ______________________________________________________________________________________ 13 MAX1146-MAX1149 Multichannel, True-Differential, Serial, 14-Bit ADCs VDD 10 OSCILLOSCOPE 10 AIN CH7 0.01F MAX1148 MAX1149 VDD DIN 0.1F 4.7F SHDN SCLK EXTERNAL CLOCK SCLK REFADJ DOUT SSTRB 0.01F DOUT* SSTRB REF VREF COM 2.2F CS CH1 DGND AGND MAX1149 VREF = +2.500V MAX1148 VREF = +4.096V VCOM AIN VREF CH2 CH3 CH4 *FULL-SCALE ANALOG INPUT, CONVERSION RESULT = $FFF HEX Figure 7. Quick-Look Circuit Table 1. Control Byte Format BIT NAME 7 (MSB) START DESCRIPTION 6 SEL2 5 SEL1 4 SEL0 3 SGL/DIF 1 = single ended, 0 = differential. Selects single-ended or differential conversions. In single-ended mode, input signal voltages are referred to COM. In differential mode, the voltage difference between two channels is measured. 2 UNI/BIP 1 = unipolar, 0 = bipolar. Selects unipolar or bipolar conversion mode. In unipolar mode, connect COM to AGND to perform conversion from 0 to VREF. In bipolar mode, connect COM to VREF/2 to perform conversion from 0 to VREF. See Table 7. 1 PD1 0 (LSB) PD0 Start bit. The first logic 1 bit after CS goes low defines the beginning of the control byte. Channel-select bits. The channel-select bits select which of the eight channels are used for the conversion (Tables 2, 3, 4, and 5). Selects clock and power-down modes. PD1 = 0 and PD0 = 0 selects full power-down mode*. PD1 = 0 and PD0 = 1 selects fast power-down mode*. PD1 = 1 and PD0 = 0 selects internal clock mode. PD1 = 1 and PD0 = 1 selects external clock mode. *The start bit resets power-down modes. 14 ______________________________________________________________________________________ Multichannel, True-Differential, Serial, 14-Bit ADCs SEL2 SEL1 SEL0 CH0 + 0 0 0 1 0 0 0 0 1 1 0 1 0 1 0 1 1 0 0 1 1 1 1 1 CH1 CH2 CH3 CH4 CH5 CH6 CH7 COM - + + + + + + + - Table 3. MAX1148/MAX1149 Channel Selection in Differential Mode (SGL/DIF = 0) SEL2 SEL1 SEL0 CH0 CH1 0 0 0 + - 0 0 1 0 1 0 0 1 1 1 0 0 1 0 1 1 1 0 1 1 1 - SEL1 SEL0 CH0 0 0 0 + 1 0 0 0 0 1 1 0 1 CH3 + - CH4 CH5 + - - CH7 + - - + + - CH1 CH6 + Table 4. MAX1146/MAX1147 Channel Selection in Single-Ended Mode (SGL/DIF = 1) SEL2 CH2 CH2 CH3 + + + + Table 5. MAX1146/MAX1147 Channel Selection in Differential Mode (SGL/DIF = 0) COM SEL2 SEL1 SEL0 CH0 CH1 - 0 0 0 + - - 0 0 1 - 1 0 0 - + - 1 0 1 Power-On Reset When power is first applied, internal power-on reset circuitry activates the MAX1146-MAX1149 in internal clock mode, making the MAX1146-MAX1149 ready to convert with SSTRB high. No conversions should be performed until the power supply is stable. The first logical 1 on DIN with CS low is interpreted as a start bit. Until a conversion takes place, DOUT shifts out zeros. Starting a Conversion Start a conversion by clocking a control byte into DIN. With CS low, a rising edge on SCLK latches a bit from DIN into the MAX1146-MAX1149 internal shift register. After CS falls, the first logic 1 bit defines the control CH2 CH3 + - - + byte's MSB. Until this start bit arrives, any number of logic 0 bits can be clocked into DIN with no effect. Table 1 shows the control-byte format. The MAX1146-MAX1149 are compatible with SPI/QSPI and MICROWIRE devices. For SPI, select the correct clock polarity and sampling edge in the SPI control registers. Set CPOL = 0 and CPHA = 0. MICROWIRE, SPI, and QSPI transmit a byte and receive a byte at the same time. Using the Typical Application Circuit (Figure 4), the simplest software interface requires only three 8-bit transfers to perform a conversion (one 8-bit transfer to configure the ADC, and two more 8-bit transfers to clock out the 14-bit conversion result). ______________________________________________________________________________________ 15 MAX1146-MAX1149 Table 2. MAX1148/MAX1149 Channel Selection in Single-Ended Mode (SGL/DIF = 1) MAX1146-MAX1149 Multichannel, True-Differential, Serial, 14-Bit ADCs Digital Output In unipolar input mode, the digital output is straight binary (Figure 14). For bipolar input mode, the digital output is two's complement binary (Figure 15). Data is clocked out on the falling edge of SCLK in MSB-first format. Use internal clock mode if the serial clock frequency is less than 100kHz or if serial clock interruptions could cause the conversion interval to exceed 140s. The conversion must complete in 140s, or droop on the T/H capacitors can degrade conversion results. Internal Clock When configured for internal clock mode, the MAX1146-MAX1149 generate an internal conversion clock. This frees the P from the burden of running the SAR conversion clock and allows the conversion results to be read back at the processor's convenience, at any clock rate up to 2.1MHz. SSTRB goes low at the start of the conversion and then goes high when the conversion is complete. SSTRB is low for a maximum of 8.0s, during which time SCLK should remain low for best noise performance. An internal register stores data when the conversion is in progress. SCLK clocks the data out of this register at any time after the conversion is complete. After SSTRB goes high, the second falling SCLK clock edge produces the MSB of the conversion at DOUT, followed by the remaining bits in MSB-first format (Figures 9 and 11). For the most accurate conversion, the MAX1146- MAX1149 digital I/O should remain inactive during the internal clock conversion interval (tCONV). Do not pull CS high during conversion. Pulling CS high aborts the current conversion. To ensure that the next start bit is recognized, clock in 18 zeros at DIN. When internal clock mode is selected, SSTRB does not go into a highimpedance state when CS goes high. A rising edge on SSTRB indicates that the MAX1146-MAX1149 have finished the conversion. The P can then read the conversion results at its convenience. Clock Modes The MAX1146-MAX1149 can use either the external serial clock or the internal clock to drive the successive-approximation conversion. The external clock shifts data in and out of the MAX1146-MAX1149. External clock mode allows the fastest throughput rate (116ksps) and serial clock frequencies from 0.1MHz to 2.1MHz. Internal clock mode provides the best noise performance because the digital interface can be idle during conversion. The internal clock mode serial clock frequency can range from 0 to 2.1MHz. Internal clock mode allows the CPU to request a conversion and clock back the results. Bits PD1 and PD0 of the control byte program the clock and power-down modes. The MAX1146-MAX1149 power up in internal clock mode with all circuits activated. Figures 8-11 illustrate the available clocking modes. External Clock In external clock mode, the external clock not only shifts data in and out, but it also drives the analog-todigital conversion. SSTRB pulses high for two clock periods after the last bit of the control byte. Successiveapproximation bit decisions are made and the results appear at DOUT on each of the next 14 SCLK falling edges (Figures 8 and10). SSTRB and DOUT go into a high-impedance state when CS is high. CS SCLK 1 8 9 16 24 CB1 DIN START SEL2 SEL1 SEL0 SGL/DIF UNI/BIP PD1 PD0 tACQ SSTRB HIGH-Z DOUT HIGH-Z HIGH-Z D13 D12 D11 D10 INPUT MUX SET ACCORDING TO PREVIOUS CONTROL BYTE INPUT T/H tCONV SET TO CB1 D9 D8 D7 OPEN TRACK D6 D5 D4 D3 D2 D1 D0 HIGH-Z RESET TO CB1 HOLD Figure 8. External Clock Mode--24 Clocks/Conversion Timing 16 ______________________________________________________________________________________ TRACK Multichannel, True-Differential, Serial, 14-Bit ADCs MAX1146-MAX1149 CS SCLK 1 8 9 16 24 CB1 DIN START SEL2 SEL1 SEL0 SGL/DIF UNI/BIP PD1 PD0 tCONV tACQ SSTRB DOUT HIGH-Z D13 D12 D11 D10 INPUT MUX SET ACCORDING TO PREVIOUS CONTROL BYTE INPUT T/H SET TO CB1 OPEN D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 HIGH-Z RESET TO CB1 TRACK HOLD TRACK Figure 9. Internal Clock Mode Timing--24 Clocks/Conversion Timing CS SCLK 1 8 1 4 10 11 18 CB1 DIN START SEL2 1 4 10 15 11 CB2 SEL1 SEL0 SGL/DIF UNI/BIP PD1 START SEL2 PD0 SEL1 SEL0 SGL/DIF UNI/BIP PD1 START SEL2 PD0 SEL1 SEL0 SGL/DIF UNI/BIP tACQ tCONV tACQ SSTRB HIGH-Z DOUT D13 D12 D5 D4 D3 D2 D1 D0 D13 D12 D5 D4 D3 D2 D1 D0 SET ACCORDING TO PREVIOUS CONTROL BYTE INPUT T/H SET TO CB2 SET TO CB1 INPUT MUX HOLD TRACK HOLD TRACK HOLD Figure 10. External Clock Mode--18 Clocks/Conversion Timing Applications Information Idle Mode The device is considered idle when all the bits have been clocked out or 18 zeros have been clocked in on DIN. Start Bit The falling edge of CS alone does not start a conversion. The first logic high clocked into DIN with CS low is interpreted as a start bit and defines the first bit of the control byte. The device begins to track on the fifth falling edge of SCLK after a start bit has been recognized. A conversion starts on the eighth falling edge of SCLK as the last bit of the control byte is being clocked in. The start bit is defined as follows: 1) The first high bit clocked into DIN with CS low any time the converter is idle. or 2) The first high bit clocked into DIN after bit 5 of a conversion in progress is clocked onto DOUT (Figures 10 and 11). Toggling CS before the current conversion is complete aborts the conversion and clears the output register. The fastest the MAX1146-MAX1149 can run with CS held low between conversions is 18 clocks per conversion. Figures 10 and 11 show the serial-interface timing necessary to perform a conversion every 18 SCLK cycles. ______________________________________________________________________________________ 17 MAX1146-MAX1149 Multichannel, True-Differential, Serial, 14-Bit ADCs CS SCLK 1 8 1 4 10 11 18 CB1 DIN 1 4 10 11 CB2 START SEL2 SEL1 SEL0 SGL/DIFUNI/BIP PD1 START SEL2 SEL1 SEL0 SGL/DIF UNI/BIP PD1 PD0 tACQ tCONV START SEL2 PD0 tACQ tCONV SSTRB HIGH-Z DOUT D13 D12 D5 D4 D3 D2 D1 D0 D13 D12 D5 D4 SET ACCORDING TO PREVIOUS CONTROL BYTE INPUT MUX SET TO CB1 INPUT T/H OPEN TRACK SET TO CB2 RESET TO CB1 HOLD TRACK OPEN HOLD RESET TO CB2 TRACK Figure 11. Internal Clock Mode--18 Clocks/Conversion Timing Shutdown and Power-Down Modes The MAX1146-MAX1149 provide a hardware shutdown and two software power-down modes. Pulling SHDN low places the converter in hardware shutdown. The conversion is immediately terminated and the supply current is reduced to 300nA. Allow 2ms for the device to power-up when the internal reference buffer is used with C REFADJ = 0.01F and C REF = 2.2F. Larger capacitors on C REFADJ and C REF increase the power-up time (Table 6). No wake-up time is needed for the device to power-up from fast powerdown when using an external reference. Select a software power-down mode through the PD1 and PD0 bits of the control byte (Table 1). When the conversion in progress is complete, software powerdown is initiated. The serial interface remains active and the last conversion result can be clocked out. In full power-down mode, only the serial interface remains operational and the supply current is reduced to 300nA. In fast power-down mode, only the bandgap reference and the serial interface remain operational, and the supply current is reduced to 600A. Table 6. Internal Reference Buffer PowerUp Times vs. Bypass Capacitors CREFADJ* CREF POWER-UP TIMES FROM AN EXTENDED POWER-DOWN 0.01F 4.7F 2ms 0.1F 10F 25ms *Power-up times are dominated by CREFADJ. 18 The MAX1146-MAX1149 automatically wake up from software power-down when they receive the control byte's start bit (Table 1). Allow 2ms for the device to power-up when the internal reference buffer is used with C REFADJ = 0.01F and C REF = 2.2F. Larger capacitors on CREFADJ and CREF increase the powerup time (Table 6). No wake-up time is needed for the device to power-up from fast power-down when using an external reference. Reference Voltage The MAX1146-MAX1149 can be used with an internal or external reference voltage. The reference voltage determines the ADC input range. The reference determines the full-scale output value (Table 7). Internal Reference The MAX1146-MAX1149 contain an internal 1.250V bandgap reference. This bandgap reference is connected to REFADJ through a 20k resistor. Bypass REFADJ with a 0.01F capacitor to AGND. The MAX1146/ MAX1148 reference buffer has a 3.277V/V gain to provide +4.096V at REF. The MAX1147/MAX1149 reference buffer has a 2.000V/V gain to provide +2.500V at REF. Bypass REF with a minimum 2.2F capacitor to AGND when using the internal reference. External Reference An external reference can be applied to the MAX1146-MAX1149 in two ways: 1) Disable the internal reference buffer by connecting REFADJ to VDD and apply the external reference to REF (Figure 12). 2) Utilize the internal reference buffer by applying an external reference to REFADJ (Figure 13). ______________________________________________________________________________________ Multichannel, True-Differential, Serial, 14-Bit ADCs +3.3V IN 24k SAR ADC MAX1146- MAX1149 REF REF 3.000V OUT MAX6163 MAX1146- MAX1149 0.1F 20k 510k 0.047F GND REFADJ +5V VDD Figure 13. Reference Adjust Circuit 0.1F 1.250V BANDGAP REFERENCE REFADJ 100k REFERENCE BUFFER DISABLED DGND with a 0.01F capacitor and bypass REF with a 2.2F capacitor to AGND. AGND Transfer Function Figure 12. External Reference Applied to REF Method 1 allows the direct application of an external reference from 1.5V to VDD + 50mV. The REF input impedance is typically 10k. During conversion, an external reference at REF must deliver up to 210A and have an output impedance less than 10. Bypass REF with a 0.1F capacitor to AGND to improve its output impedance. Method 2 utilizes the internal reference buffer to reduce the external reference load. The REFADJ input impedance is typically 20k. During a conversion, an external reference at REFADJ must deliver at least 100A and have an output impedance less than 100. The MAX1146/MAX1148 reference buffer has a 3.277V/V gain and the MAX1147/MAX1149 has a gain of 2.000V/V. The external reference voltage at REFADJ multiplied by the reference buffer gain is the SAR ADC reference voltage. This reference appears at REF and must be from 1.5V to VDD + 50mV. Bypass REFADJ Table 7 shows the full-scale voltage ranges for unipolar and bipolar modes. Output data coding for the MAX1146-MAX1149 is binary in unipolar mode and two's complement binary in bipolar mode with 1 LSB = (VREF/2N), where N is the number of bits (14). Code transitions occur halfway between successive-integer LSB values. Figure 14 and Figure 15 show the input/output (I/O) transfer functions for unipolar and bipolar operations, respectively. Serial Interfaces The MAX1146-MAX1149 feature a serial interface that is fully compatible with SPI, QSPI, and MICROWIRE. If a serial interface is available, establish the CPU's serial interface as a master, so that the CPU generates the serial clock for the ADCs. Select a clock frequency up to 2.1MHz. SPI and MICROWIRE Interface When using an SPI (Figure 16a) or MICROWIRE interface (Figure 16b), set CPOL = CPHA = 0. Two 8-bit readings are necessary to obtain the entire 14-bit result from the ADC. DOUT data transitions on the serial clock's falling Table 7. Full Scale and Zero Scale UNIPOLAR MODE INPUT AND OUTPUT MODES ZERO SCALE FULL SCALE Single-Ended Mode VCOM VREF + VCOM Differential Mode VIN- VREF + VIN- BIPOLAR MODE NEGATIVE FULL SCALE -V REF + V COM 2 -V REF + V - IN 2 ZERO SCALE VCOM VIN- POSITIVE FULL SCALE + VREF 2 + VCOM + VREF + VIN - 2 Note: The common mode range for the analog inputs is from AGND to VDD. ______________________________________________________________________________________ 19 MAX1146-MAX1149 +5V 1 LSB = VREF 16384 1 LSB = VREF 0...011 0...010 0...001 0...000 1 2 3 16381 16383 0...111 0...110 0...101 0...100 0...001 VREF 1...101 1...100 TWO'S COMPLEMENT BINARY OUTPUT CODE (LSB) 1...111 1...110 0 VREF 16384 VREF VREF BINARY OUTPUT CODE (LSB) MAX1146-MAX1149 Multichannel, True-Differential, Serial, 14-Bit ADCs 0...000 1...111 1...011 1...010 1...001 1...000 0 1 2 3 INPUT VOLTAGE (LSB) 8191 8193 8192 INPUT VOLTAGE (LSB) 16381 16383 Figure 14. Unipolar Transfer Function Figure 15. Bipolar Transfer Function edge and is clocked into the P on SCLK's rising edge. The first 8-bit data stream contains the first 8-bits of DOUT starting with the MSB. The second 8-bit data stream contains the remaining 6 result bits. munication, connect the controller as shown in Figure 18 and configure the PIC16/PIC17 as system master. Initialize the synchronous serial-port control register (SSPCON) and synchronous serial-port status register (SSPSTAT) to the bit patterns shown in Tables 8 and 9. In SPI mode, the PIC16/PIC17 Cs allow 8 bits of data to be synchronously transmitted and received simultaneously. Two consecutive 8-bit readings are necessary to obtain the entire 14-bit result from the ADC. DOUT data transitions on the serial clock's falling edge and is clocked into the C on SCLK's rising edge. The first 8bit data stream contains the first 8 data bits starting with the MSB. The second data stream contains the remaining bits, D5 through D0. QSPI Interface Using the high-speed QSPI interface (Figure 17) with CPOL = 0 and CPHA = 0, the MAX1146-MAX1149 support a maximum fSCLK of 2.1MHz. One 16-bit reading is necessary to obtain the entire 14-bit result from the ADC. DOUT data transitions on the serial clock's falling edge and is clocked into the P on SCLK's rising edge. The first 14 bits are the data. PIC16/PIC17 SSP Module Interface The MAX1146-MAX1149 are compatible with a PIC16/PIC17 microcontroller (C), using the synchronous serial-port (SSP) module. To establish SPI com- I/O CS I/O CS SCK SCLK SK SCLK MISO DOUT SI DOUT VDD MICROWIRE SPI SS Figure 16a. SPI Connections 20 MAX1146- MAX1149 MAX1146- MAX1149 Figure 16b. MICROWIRE Connections ______________________________________________________________________________________ Multichannel, True-Differential, Serial, 14-Bit ADCs CS MAX1146-MAX1149 VDD VDD CS SCK SCLK SCLK SCK MISO DOUT DOUT SDI CS I/O VDD QSPI MAX1146- MAX1149 SS PIC16/PIC17 MAX1146- MAX1149 Figure 17. QSPI Connections GND GND Figure 18. SPI Interface Connection for a PIC16/PIC17 Controller Table 8. Detailed SSPCON Register Content PICI6/PICI7 SETTINGS CONTROL BIT SYNCHRONOUS SERIAL-PORT CONTROL REGISTER (SSPCON) WCOL Bit 7 X Write collision detection bit. SSPOV Bit 6 X Receive overflow detect bit. SSPEN Bit 5 1 Synchronous serial port enable bit: 0: Disables serial port and configures these pins as I/O port pins. 1: Enables serial port and configures SCK, SDO, and SCI pins as serial-port pins. Clock polarity select bit. CKP = 0 for SPI master mode selection. CKP Bit 4 0 SSPM3 Bit 3 0 SSPM2 Bit 2 0 SSPM1 Bit 1 0 SSPM0 Bit 0 1 Synchronous serial port mode select bit. Sets SPI master mode and selects FCLK = fOSC / 16. Table 9. Detailed SSPSTAT Register Content MAX1146-MAX1149 SETTINGS CONTROL BIT SYNCHRONOUS SERIAL-PORT STATUS REGISTER (SSPSTAT) SMP Bit 7 0 SPI data input sample phase. Input data is sampled at the middle of the data output time. CKE Bit 6 1 SPI clock edge select bit. Data is transmitted on the rising edge of the serial clock. D/A Bit 5 X Data address bit. P Bit 4 X Stop bit. S Bit 3 X Start bit. R/W Bit 2 X Read/write bit information. UA Bit 1 X Update address. BF Bit 0 X Buffer full status bit. ______________________________________________________________________________________ 21 MAX1146-MAX1149 Multichannel, True-Differential, Serial, 14-Bit ADCs TMS32OLC3x Interface Figure 19 shows an application circuit to interface the MAX1146-MAX1149 to the TMS320 in external clock mode. The timing diagram for this interface circuit is shown in Figure 20. Use the following steps to initiate a conversion in the MAX1146-MAX1149 and to read the results: Layout, Grounding, and Bypassing Careful PC board layout is essential for best system performance. Boards should have separate analog and digital ground planes. Ensure that digital and analog signals are separated from each other. Do not run analog and digital (especially clock) lines parallel to one another, or digital lines underneath the device package. 1) The TMS320 should be configured with CLKX (transmit clock) as an active-high output clock and CLKR (TMS320 receive clock) as an active-high input clock. CLKX and CLKR on the TMS320 are connected together with the MAX1146-MAX1149 SCLK input. Figure 4 shows the recommended system ground connections. Establish an analog ground point at AGND and a digital ground point at DGND. Connect all analog grounds to the star analog ground. Connect the digital grounds to the star digital ground. Connect the digital ground point to the analog ground point directly at the device. For lowest noise operation, the ground return to the star ground's power supply should be low impedance and as short as possible. 2) Drive the CS of the MAX1146-MAX1149 low through the XF_ I/O port of the TMS320 to clock data into the MAX1146-MAX1149 DIN. 3) Write an 8-bit word (1XXXXX11) to the MAX1146-MAX1149 to initiate a conversion and place the device into external clock mode. Refer to Table 1 to select the proper XXXXX bit values for your specific application. XF CS TMS320LC3x 4) The MAX1146-MAX1149 SSTRB output is monitored by the FSR input of the TMS320. A falling edge on the SSTRB output indicates that the conversion is in progress and data is ready to be received from the MAX1146-MAX1149. SCLK CLKX CLKR MAX1146- MAX1149 5) The TMS320 reads in one data bit on each of the next 16 rising edges of SCLK. These data bits represent the 14-bit conversion result followed by 2 trailing bits, which should be ignored. DX DIN DR DOUT 6) Pull CS high to disable the MAX1146-MAX1149 until the next conversion is initiated. FSR SSTRB Figure 19. MAX1146-MAX1149-to-TMS320 Serial Interface CS SCLK DIN START SEL2 SEL1 SEL0 SGL/DIF UNI/BIP PD1 PD0 HIGH-Z SSTRB DOUT MSB B12 B1 LSB Figure 20. TMS320 Serial-Interface Timing Diagram 22 ______________________________________________________________________________________ HIGH-Z Multichannel, True-Differential, Serial, 14-Bit ADCs Definitions Integral Nonlinearity Integral nonlinearity (INL) is the deviation of the values on an actual transfer function from a straight line. This straight line can be either a best-straight-line fit or a line drawn between the end points of the transfer function, once offset and gain errors have been nullified. The static linearity parameters for the MAX1146-MAX1149 are measured using the end-point method. Differential Nonlinearity Differential nonlinearity (DNL) is the difference between an actual step width and the ideal value of 1 LSB. A DNL error specification of less than 1 LSB guarantees no missing codes and a monotonic transfer function. Aperture Definitions Aperture jitter (tAJ) is the sample-to-sample variation in the time between the samples. Aperture delay (tAD) is the time between the rising edge of the sampling clock and the instant when an actual sample is taken. Signal-to-Noise Ratio For a waveform perfectly reconstructed from digital samples, signal-to-noise ratio (SNR) is the ratio of full-scale analog input (RMS value) to the RMS quantization error (residual error). The ideal, theoretical minimum analogto-digital noise is caused by quantization error only and results directly from the ADC's resolution (N bits): SNR = (6.02 x N + 1.76)dB In reality, there are other noise sources besides quantization noise: thermal noise, reference noise, clock jitter, etc. SNR is computed by taking the ratio of the RMS signal to the RMS noise, which includes all spectral components minus the fundamental, the first five harmonics, and the DC offset. Signal-to-Noise Plus Distortion Signal-to-noise plus distortion (SINAD) is the ratio of the fundamental input frequency's RMS amplitude to RMS equivalent of all other ADC output signals. SINAD(dB) = 20 x log (SignalRMS / NoiseRMS) Effective Number of Bits Effective number of bits (ENOB) indicates the global accuracy of an ADC at a specific input frequency and sampling rate. An ideal ADC's error consists of quantization noise only. With an input range equal to the fullscale range of the ADC, calculate the ENOB as follows: ENOB = (SINAD - 1.76) / 6.02 Total Harmonic Distortion Total harmonic distortion (THD) is the ratio of the RMS sum of the first five harmonics of the input signal to the fundamental itself. This is expressed as: V 2 + V32 + V4 2 + V52 THD = 20 x log 2 V1 where V1 is the fundamental amplitude, and V2 through V5 are the amplitudes of the 2nd- through 5th-order harmonics. Spurious-Free Dynamic Range Spurious-free dynamic range (SFDR) is the ratio of RMS amplitude of the fundamental (maximum signal component) to the RMS value of the next-largest distortion component. Chip Information TRANSISTOR COUNT: 5589 PROCESS: BiCMOS Revision History Pages changed at Rev 2: 1, 20, 23, 25. ______________________________________________________________________________________ 23 MAX1146-MAX1149 High-frequency noise in the VDD power supply degrades the device's high-speed performance. Bypass the supply to the digital ground with 0.1F and 4.7F capacitors. Minimize capacitor lead lengths for best supply-noise rejection. Connect a 10 resistor in series with the 0.1F capacitor to form a lowpass filter when the power supply is noisy. Multichannel, True-Differential, Serial, 14-Bit ADCs MAX1146-MAX1149 Pin Configurations TOP VIEW CH0 1 20 VDD CH0 1 20 VDD CH1 2 19 SCLK CH1 2 19 SCLK CH2 3 18 CS CH2 3 18 CS 17 DIN CH3 4 CH3 4 N.C. 5 MAX1146 MAX1147 16 SSTRB CH4 5 15 DOUT CH5 6 N.C. 7 14 DGND CH6 7 14 DGND N.C. 8 13 AGND CH7 8 13 AGND COM 9 12 REFADJ COM 9 12 REFADJ N.C. 6 SHDN 10 11 REF TSSOP 24 17 DIN MAX1148 MAX1149 SHDN 10 16 SSTRB 15 DOUT 11 REF TSSOP ______________________________________________________________________________________ Multichannel, True-Differential, Serial, 14-Bit ADCs TSSOP4.40mm.EPS PACKAGE OUTLINE, TSSOP 4.40mm BODY 21-0066 I 1 1 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 25 (c) 2007 Maxim Integrated Products is a registered trademark of Maxim Integrated Products. MAX1146-MAX1149 Package Information (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.)