IAL/CEL/LEL Series
Magnetic Circuit Protectors
133
134
136
140
143
145
149
151
Introduction
Poles
Handles
Configurations
Operating Characteristics
Delay Curves
Specifications
Decision Tables
INTRODUCTION
IAL/IUL/IEL/LEL magnetic circuit protectors provide low-cost
power switching, reliable circuit protection and accurate
circuit control for equipment in the international marketplace.
IAL models are for those applications where the unit’s inherent
attributes are desired, but compliance with the various
standards is not required.
IUL models have been tested and approved in accordance with
UL 1077 requirements for UL recognition.
IEL/LEL models are VDE approved to VDE 0660, part 101. They
meet IEC spacing requirements, mandatory for equipment
which must comply with IEC specifications 601 and 950, and
VDE specifications 0804 and 0805. In addition, the IEL models
are UL recognized to UL 1077 as supplementary protectors and
the LEL models are UL listed under the conditions of UL 489. Both
are CSA certified and CCC Approved. The IEL is CSA certified as
a supplementary protector per CSA C22.2–No. 235.
The CEL model has achieved two new enhancements, including
a single pole, 125 amp rating with TÜV approval, and a parallel
4-pole version with 400 amp rating.
Airpax™ IAL/CEL/LEL circuit protectors are available in a wide
variety of configurations, including series, series with auxiliary
switch, shunt and relay with choice of delays and ratings in DC
and/or 50/60Hz or 400Hz versions. Single or multi-pole versions
are available with a variety of pole arrangements to meet your
specifications. Please see the appropriate product specification
table for ratings and limitations.
IAL/CEL/LEL Series
Hydraulic Magnetic Circuit Protectors
IAL Series - Introduction http://airpax.sensata.com
133
SINGLE POLE, STANDARD STUD TERMINAL
[19.05]
.750
[36.53]
1.438
[63.24]
2.490
[10.21]
.402 [5.59]
.220
[52.32]
2.060
2X 6-32 THREAD
.140 [3.56] DEEP
M3 ISO THD. OPTIONAL
(SEE TABLE)
(SEE TABLE) [3.56]
.140
[3.61]
.142
[47.22]
1.859 [17.53]
.690
ON
OFF
[7.14]
.281
[49.28]
1.940
[7.13]
.281
[49.28]
1.940
[3.61]
.142
Screw Terminal
[7.13]
.281
[49.28]
1.940
[6.35]
ÿ .250 MAX.
[15.04]
.592
[9.96]
.392
[9.53]
.375
Single Pole
Clip Terminal
[24.57]
.967
Bullet Terminal
Notes:
Tolerance ± .015 [.39] unless noted.
Dimensions in brackets [ ] are millimeters.
A Terminal protrusion dimensions are referenced from back of mounting
panel.
B Each screw terminal is supplied with a 10-32x.312 [7.92] or M5 x 8mm
screw, flatwasher and external tooth lockwasher.
C Stud terminals are supplied with a flatwasher, external tooth lockwasher
and a 10-32 or M5 hex nut (<=70A) (<=50A for LEL),1/4-20 or M6 hex nut
(>70A)(>50A for LEL).
[19.18]
.755
[52.32]
2.060
[36.78]
1.448
[3.96]
2X ÿ .156
[10.98]
.432
Mounting Detail
Note: Each outer terminal is supplied with a
flatwasher, tooth lockwasher and a hex nut.
Bullet terminal receptacle should be .312 ± .001
diameter hole not less than .250 depth. Contact
Sensata for other bullet sizes.
STUD TERMINAL TYPES
Screw Stud Thread Dimension “A” Dimension “B”
M6 .510 ± .045
[12.95 ± 1.14]
.652 ± .035
[16.56 ± 0.89]
1/4 -20 .545 ± .045
[13.84 ± 1.14]
.687 ± .035
[17.45 ± 0.89]
M5 .510 ± .045
[12.95 ± 1.14]
.652 ± .035
[16.56 ± 0.89]
10-32 .545 ± .045
[13.84 ± 1.14]
.687 ± .035
[17.45 ± 0.89]
Panel Mounting Detail
Tolerance ±.005 [.13] unless noted.
IAL Series - Poles
IAL Series
134
Note:
A Terminal protrusion dimensions are referenced from back of mounting panel.
B Each screw terminal is supplied with a 10-32x.312 [7.92] or M5 x 8mm screw, flatwasher and external tooth lockwasher.
C Stud terminals are supplied with a flatwasher, external tooth lockwasher and a 10-32 or M5 hex nut (<=70A), 1/4 -20 or M6 hex nut (>70A).
(SEE TABLE)
(SEE TABLE) [3.56]
.140
[3.61]
.142
[47.22]
1.859 [17.53]
.690
ON
OFF
[7.14]
.281
[49.28]
1.940
Two Pole
[5.59]
.220
MAX.
[36.53]
1.438
[63.24]
2.490
[10.21]
.402
[52.32]
2.060
[38.48]
1.515
4X 6-32 THREAD
.140 [3.56] DEEP
M3 ISO THD. OPTIONAL
MAX.
[38.48]
1.515
IELH11 IEL11
Note:
Tolerance ± .015 [.38] unless noted.
Dimensions in brackets [ ] are millimeters.
[19.05]
.750
[52.32]
2.060
[38.86]
1.530
[36.78]
1.448
[10.97]
.432
[3.96]
4X ÿ .156
Two Pole*
[19.05]
.750
Two Pole*
M6
1/4 - 20
M5
10 - 32
Screw stud
thread
.510
.545
.510
.545
Dim. ìAî
(± .045)
.652
.687
.652
.687
Dim. ìBî
(± .035)
Note:
Each outer terminal is supplied with a flatwasher, tooth
lockwasher and a hex nut. Panel Mounting Detail
Tolerance ±.005 [.13] unless noted.
Multi-pole units are combined in an assembly with the trip
mechanisms internally coupled. A fault in any protected circuit
opens all poles simultaneously. Applications include use in
polyphase circuits, single-phase three-wire systems, or in two
or more related but electrically isolated circuits. A mix of
delays, ratings and configurations are offered. The auxiliary
switch is offered with either gold or silver contacts and is
available when a series construction pole is specified.
Two Pole Units
An assembly consisting of two single pole units, having their trip
mechanisms internally coupled, is available with either a single
toggle handle or with a handle per pole. Please see decision
one of the part number decision tables. Individual poles may
vary in ratings, delays and internal configurations. If the poles
are of series construction, an auxiliary switch may be included
in either or both poles, allowing you to mix SELV and hazardous
voltages.
MULTI-POLE CIRCUIT PROTECTORS
IAL Series - Poles http://airpax.sensata.com
135
[57.53]
2.265
MAX.
Three Pole and Four Pole Units
The three pole structure consists of three single pole units
assembled with an internal mechanical interlock which
actuates all units simultaneously. The units are available
with either a single toggle handle or with a handle per pole.
Units with four pole construction operate with a minimum
of two center toggle handles or with a handle per pole.
Please see decision one of the part number decision tables.
Mixing of delays, ratings and configurations is available in
each individual pole. The auxiliary switch is offered in any
series trip pole.
Breaker poles are numbered consecutively when viewed
from the terminal side, with the ON position up, starting with
pole #1 on the left side and proceeding to the right.
Three Pole
IEL111
MAX.
[57.53]
2.265
Mounting Detail*
[19.05]
.750
[19.05]
.750
[57.91]
2.280
MAX.
[76.58]
3.015
Four Pole
IEL1111
[19.05]
.750
[19.05]
.750
[19.05]
.750
[38.86]
1.530
Mounting Detail*
[19.05]
.750
[19.05]
.750
Note:
Tolerance ± .015 [.39] unless noted. Dimensions in brackets [ ] are millimeters.
*See Single Pole Mounting Detail for Hole Sizes and Locations.
Three Pole
IELH111
MAX.
[76.58]
3.015
[19.05]
.750
[19.05]
.750
[19.05]
.750
[76.96]
3.030
Mounting Detail*
Four Pole
IELH1111
Mounting Detail*
BX - FLAT ROCKER HANDLE
The innovative new design of our IAL/CEL/LEL BX Style
circuit protectors features a flat rocker that will satisfy your
aesthetic needs while guarding against accidental
actuation, providing the highest degree of circuit protection
and quality. Only Airpax offers this new standard in user
interface. Available on a variety of versions with a full range
of agency approvals, the IEL BX style circuit protectors meet
or exceed all current performance specifications, including
interrupting capacities up to 50,000 amperes.
1.239
[31.47]
.387 REF.
[9.84]
.768
[19.49]
1.859
[47.22]
2.490 MAX.
[63.25]
2.173 MAX.
[55.19]
.314
[7.98]
1.395
[35.43]
.125
[3.17]
6-32 THD. MOUNTING
M3 ISO THD. OPTIONAL
1.660
[42.16]
.750 MAX.
[19.05]
OPTIONAL
GUARD
(SEE DETAIL ìCî) SINGLE POLE
1.660
[42.16]
.750
[19.05]
1.260
[32.00]
.200
[5.08]
2X ÿ.156
[3.96]
Panel Mounting Detail
Mounting Detail Tolerance:
±.005 [.13] unless noted
ON
I
ON
I
ACTUATION
ACCESS
(SEE NOTE)
DETAIL "A"
ON
I
O
OFF
ON
I
O
OFF
ON
I
O
OFF
ON
I
OFF
O
HANDLE
POSITION "OFF"
GUARD WITH NO ACTUATE
OFF FEATURE
(SIXTH DECISION, X)
HANDLE
POSITION "ON"
GUARD WITH NO ACTUATE
OFF FEATURE
(SIXTH DECISION, X)
PUSH
TO
RESET
NOTE: ACCESS IS LIMITED TO A DEVICE SMALLER THAN THE
UNDERWRITERS LABORATORY "ARTICULATED PROBE"
DEFINED IN UL-489 FIG. 11.1.7.2.1.
HANDLE
POSITION "OFF"
WITH GUARD
(SIXTH DECISION, G)
HANDLE
POSITION "ON"
WITH GUARD
(SIXTH DECISION, G)
HANDLE
POSITION "OFF"
WITHOUT GUARD
HANDLE
POSITION "ON"
WITHOUT GUARD
PUSH
TO
RESET
Panel Mounting Detail
Tolerance ±.005 [.13] unless noted.
IAL Series - Handles
IAL Series
136
The Airpax™ LELHP/CELHP high current magnetic circuit protector compliments our entire series of LEL circuit protectors. Its unique,
parallel current sensing design provides precise current overload protection and reliability in the compact size of a two pole LEL.
The unit is ideal for high power DC applications such as drive motor systems and telecommunication power systems.
LEL is available in series and series with auxiliary switch configurations with a choice of delays for DC ratings of 125, 150, 175 and 200
amperes. The CEL has been enhanced to include these same ratings plus a 4-pole, parallel 400 amp rating for UL489A. The LELHP is
UL listed under the conditions of UL489 and CSA certified. The CELHP is UL listed under the conditions of UL489A. Mid-trip handle
indication, voltage trip and remote operator options complete the LELHP/CELHP circuit breaker series. Please see the individual
product tables for approved ratings.
Series Parallel
ON
OFF
[17.53]
.690
[47.22]
1.859
[49.28]
1.940
[7.14]
.281
[3.56]
.140
[13.84]
.545
[16.26]
.640
[26.59]
1.047
[32.56]
1.282
[17.45]
.687
1/4-20 STUD
(M6 x 1.0 STUD
OPTION)
[52.32]
2.060
[5.59]
.220
[36.53]
1.438
[10.21]
.402
[63.25]
2.490
[19.05]
.750
2X 6-32 THREAD
.140 [3.56] DEEP
M3 ISO THD OPTIONAL
C
NO
NC
BREAKER IN
OFF POSITION
Series Parallel with optional
1REC4 Auxiliary switch
Notes:
Tolerance ± .015 [.39] unless noted. Dimensions in brackets [ ] are millimeters.
A Terminal protrusion dimensions are referenced from back of mounting panel.
B Each screw terminal is supplied with a 10-32x.312[7.92] or M5 x 8mm screw,
flatwasher and external tooth lockwasher.
C Stud terminals are supplied with a flatwasher, external tooth lockwasher and
a 10-32 or M5 hex nut (<=70A), 1/4 -20 or M6 hex nut (>70A).
D Units are supplied without bus bars must have a minimum copper strap (1
31/32 x 1/2 x 1/16 ) of appropriate length to accommodate connections tying
each set of terminals together.
E Other spacing available upon request. Contact factory for assistance.
[6.60]
.260
[2.79]
.110
2.438 MAX
[61.93]
(SEE NOTE 1)
-REC4
[38.48]
1.515 MAX
[18.80]
.740
(Note E)
32
32
[17.53]
.690
[47.22]
1.859
6X
6X
[49.28]
1.940
[7.14]
.281
[3.56]
.140
[6.40]
.252
[36.53]
1.438
[10.21]
.402
[63.25]
2.490
[57.53]
2.265 MAX.
6X
[14.10]
.555
[7.90]
.311
[10.77]
.424
[7.59]
.299
[18.80]
(Note E)
.740
[50.83]
2.001
OFF
[3.61]
.142
[17.45]
.687
[13.84]
.545
OFF OFF
[32.77]
1.290
[16.46]
.648
ON
OFF
[52.32]
2.060
[5.59]
.220
6X 1/4-20 STUD
6X 6-32 THREAD
.140 [3.56] DEEP
M3 ISO THD OPTIONAL
1.055
[26.79]
[18.80]
(Note E)
.740
Two Pole
Three Pole (Note D)
175/200 Parallel Pole
32
32
[17.53]
.690
[47.22]
1.859
6X
6X
[49.28]
1.940
[7.14]
.281
[3.56]
.140
[6.40]
.252
[36.53]
1.438
[10.21]
.402
[63.25]
2.490
[57.53]
2.265 MAX.
6X
[14.10]
.555
[7.90]
.311
[10.77]
.424
[7.59]
.299
[18.80]
(Note E)
.740
[50.83]
2.001
OFF
[3.61]
.142
[17.45]
.687
[13.84]
.545
OFF OFF
[32.77]
1.290
[16.46]
.648
ON
OFF
[52.32]
2.060
[5.59]
.220
6X 1/4-20 STUD
6X 6-32 THREAD
.140 [3.56] DEEP
M3 ISO THD OPTIONAL
1.055
[26.79]
[18.80]
(Note E)
.740
LELHP/CELHP CIRCUIT PROTECTORS
Four Pole (CEL _ _ P and CML _ _ P only)
8X 6-32 THREAD
.140 [3.56] DEEP
M3 ISO THD OPTIONAL
OF
FF
FOFFOFFO
3.005
[76.33]
.402
10.21
1.438
36.53
2.490
63.25
.220
5.59
2.060
52.32
(SEE TABLE)
DIM. "H"
(SEE TABLE)
DIM. "H"
(SEE TABLE)
DIM. "H"
MAX
IAL Series - Handles http://airpax.sensata.com
137
The lALN/IULN family is a sealed toggle version of the IAL/IUL
family. The silicone rubber seal around the handle assures
panel seal integrity and makes this style a natural for harsh
environments.
This sealed toggle family is available in one to three pole
models with ratings of .050 to 100 amperes.
[34.92]
1.375
[16.66]
.656
[63.25]
2.490
[19.05]
.750
KEYWAY
.060 [1.52]-.065 [1.65] WIDE
.030 [.76]-.035 [.89] DEEP
[38.48]
1.515
(OPTIONAL, HANDLE
MAY BE IN POLE 2
INSTEAD OF POLE 1)
MAX.
[57.53]
2.265
MAX.
Three Pole
Single Pole Two Pole
(Optional handle may be in
pole 2 instead
of pole 1.)
[13.08]
ÿ.515
[3.96]
ÿ.156
[16.66]
.656
[19.05]
.750
MAX.
[19.05]
.750
[19.05]
.750
MAX. MAX.
[51.82]
2.040
[3.30]
.130
ON
OFF
6-32 MTG. SCREW
1/2-32 HEX NUT
LOCKWASHER
[19.05]
.750
[15.88]
.625
[3.61]
.142
FOR HIGH SHOCK
MTG.
Optional handle
Notes:
A Terminal protrusion dimensions are referenced from back of mounting panel.
B Each screw terminal is supplied with a 10-32x.312[7.92] or M5 x 8mm screw, flatwasher and external tooth lockwasher.
C Stud terminals are supplied with a flatwasher, external tooth lockwasher and a 10-32 or M5 hex nut (<=70A), 1/4 -20 or M6 hex nut (>70A).
Panel Mounting Details: Tolerance ±.005 [.13] Unless noted.
Single Pole Two Pole* Three Pole*
*See Single Pole Mounting Detail for Hole
Sizes and Locations.
IALN/IULN PANEL SEAL CIRCUIT PROTECTORS
IAL Series - Handles
IAL Series
138
Two Pole Three Pole Four Pole
The rocker style is available in one to four poles. Choose
either vertical or horizontal mounting with ON-OFF,
international markings or a combination of both.
Five front panel enhancing colors including black, white, red,
grey and orange are available.
[47.22]
1.859
[57.12]
2.249
[10.65]
.419
[34.92]
1.375
[63.25]
2.490
[49.28]
1.940
[3.61]
Note: Tolerance ± .015 [.38] unless noted.
Dimensions in brackets [ ] are millimeters.
OFF
ON
[19.05]
.750
[42.16]
1.660
[50.09]
1.972
[18.67]
2.361
2X 6-32 THD. (TYP.)
M3 ISO THD.
OPTIONAL
.735
(HANDLE WIDTH)
OFF
ON
MAX.
[38.07]
1.499
OFF
ON
MAX.
[57.12]
2.249
OFF
ON
OFF
ON
MAX.
[76.58]
3.015
[19.05]
.750
[42.17]
1.660
[3.96]
2X ÿ .156
1.260
[32.00]
[5.08]
.200
[38.35]
1.510
[19.05]
.750
[32.00]
1.260
Note:
A Terminal protrusion dimensions are referenced from back of mounting panel.
B Each screw terminal is supplied with a 10-32x.312[7.92] or M5 x 8mm screw,
flatwasher and external tooth lockwasher.
C Stud terminals are supplied with a flatwasher, external tooth lock washer and
a 10-32 or M5 hex nut (<=70A), º -20 or M6 hex nut (>70A).
Single Pole Panel Mounting Detail*
Single,Two & Three Pole Four Pole**
*Mounting detail tolerance ±.005 [.13] Unless noted.
**See single mounting detail for hole sizes and locations.
(Optional handle may be in
Pole 2 instead of Pole 1.)
The IALZX/IULZX/IELZX style adds our rocker handle options of
contrasting dual color rocker actuators, affording a clear visual
indication of the handle position and integrated handle guards, to
1.239
[31.47]
.420 REF
[10.67]
.750 MAX.
[19.05]
2X 6-32 THD.
M3 ISO THD.
OPTIONAL
ON
.506
[12.85]
OPTIONAL
HANDLE GUARDS
1.660
[42.16]
OFF
.772
[19.62]
Panel Mounting Details
Mounting Detail Tolerance:
±.005 [.13] Unless Noted.
1.859
[47.22]
2.173 MAX.
[55.19]
.314
[7.98]
.201
[5.11]
1.395
[35.43]
2.490 MAX.
[63.25]
1.660
[42.17]
.750
[19.05]
1.260
[32.00]
2X ÿ .156
[3.96]
.200
[5.08]
1.239
[31.47]
.420 REF
[10.67]
.750 MAX.
[19.05]
2X 6-32 THD.
M3 ISO THD.
OPTIONAL
ON
.506
[12.85]
OPTIONAL
HANDLE GUARDS
1.660
[42.16]
OFF
.772
[19.62]
Panel Mounting Details
Mounting Detail Tolerance:
±.005 [.13] Unless Noted.
1.859
[47.22]
2.173 MAX.
[55.19]
.314
[7.98]
.201
[5.11]
1.395
[35.43]
2.490 MAX.
[63.25]
1.660
[42.17]
.750
[19.05]
1.260
[32.00]
2X ÿ .156
[3.96]
.200
[5.08]
Panel Mounting Detail
help prevent accidental turn-on and turn-off of the unit. Available
with a black rocker and white, red or green indicator color for
either ON or OFF indication.
IALX/IULX/IELX ROCKER HANDLE
IALZX/IULZX/IELZX ROCKER HANDLE
Panel Mounting Detail
Tolerance ±.005 [.13] unless noted.
IAL Series - Handles http://airpax.sensata.com
139
Series Trip
The most popular configuration for magnetic
protectors is the series trip where the sensing coil
and contacts are in series with the load being
protected. The handle position conveniently
indicates circuit status. In addition to providing
conventional overcurrent protection, it’s
simultaneously used as an on-off switch.
Shunt Trip
The shunt trip is designed for controlling two
separate loads with one assembly. The control is
established by providing overload protection for the
critical load. When the current through this load
becomes excessive and reaches the trip point, the
protector will open and remove power from both
loads simultaneously. The total current rating of both
loads must not exceed the maximum contact rating.
Dual Coil
By combining two electrically independent coils on
a common magnetic circuit, it is possible to provide
contact opening when either an over-current or trip
voltage is applied to the respective coils. One coil
will be a current trip coil with standard
specifications. The second, or dual coil, can be used
to provide a control function permitting contact
opening from a remote interlock or other transducer
functions. Standard coils are 6, 12, 24, 48, 120 and
240 volts. Tripping is instantaneous and must be
removed (usually self-interrupting) after trip.
Auxiliary Switch (Applies to Series Trip Only)
This is furnished as an integral part of a series pole
in single or multi-pole assemblies. Isolated
electrically from the protector’s circuit, the switch
works in unison with the power contacts and
provides indication at a remote location of the
protector’s on-off status.
Auxiliary switch contacts actuate simultaneously
with the main breaker contacts, and will open
regardless of whether the breaker contacts are
opened manually or electrically. For auxiliary switch
ratings below 6Vac or 5Vdc, an auxiliary switch with
gold contacts, designated as REG is available. Gold
contacts are not recommended for load current
above 100 milliamps.
SWITCH ONLYSERIES
1.940
[49.28]
.281
[7.13] Dimension B
(See Table)
Dimension A
(See Table)
1.290
[32.77]
.648
[16.46]
1.055
[26.80]
NC
NO
C
BREAKER IN OFF POSITION
1.26
[32.00]
.278
[7.05]
1.940
[49.28]
2.640 MAX.
[67.06]
(SEE NOTE A)
.795
[20.19]
.660 ±.045
[16.76] ±1.14]
1.266
[32.16]
.971
[24.66]
.676
[17.17]
Dimension B
(See Table)
-IREC5
.250
[6.35]
.187
[4.75]
-IREC4, -IREG4
.260
[6.60]
.110
[2.79]
2.454 MAX.
[64.52]
(SEE NOTE A)
2.438 MAX.
[64.52]
(SEE NOTE A)
-IREC5
.250
[6.35]
.187
[4.75]
-IREC4, -IREG4
.260
[6.60]
.110
[2.79]
2.454 MAX.
[64.52]
(SEE NOTE A)
2.438 MAX.
[64.52]
(SEE NOTE A)
DUAL COILSHUNT
Spacing for VDE Switch
Series with Auxiliary Switch
[17.17]
.676
[24.66]
.971
[32.16]
1.266
Note: Each outer terminal is supplied with a flatwasher,
tooth lockwasher and a hex nut.
Note:
A Terminal protrusion dimensions are referenced from back of mounting
panel.
B Each screw terminal is supplied with a 10-32x.312[7.92] or M5 x 8mm
screw, flatwasher and external tooth lockwasher.
C Stud terminals are supplied with a flatwasher, external tooth lock
washer and a 10-32 or M5 hex nut (<=70A), 1/4-20 or M6 hex nut (>70A).
Series and Switch Only
Shunt and Dual Coil
CONFIGURATIONS
STUD TERMINAL TYPES
Screw Stud Thread Dimension “A” Dimension “B”
M6 .510 ± .045
[12.95 ± 1.14]
.652 ± .035
[16.56 ± 0.89]
1/4 -20 .545 ± .045
[13.84 ± 1.14]
.687 ± .035
[17.45 ± 0.89]
M5 .510 ± .045
[12.95 ± 1.14]
.652 ± .035
[16.56 ± 0.89]
10-32 .545 ± .045
[13.84 ± 1.14]
.687 ± .035
[17.45 ± 0.89]
IAL Series - Congurations
IAL Series
140
Relay Trip
This permits the overload sensing coil to be placed in a
circuit which is electrically isolated from the trip contacts.
The coil may be actuated by sensors monitoring pressure,
flow, temperature, speed, etc. Other typical applications
include crowbar, interlock and emergency/rapid shutdown
circuitry. Trip may be accomplished by voltage or current,
which must be removed after trip.
Voltage Trip
Sometimes called “dump circuits” or “panic trip circuits,”
these units make it possible to open main power contacts
with lower power inputs from one or more sources. This
configuration is becoming increasingly more important for
sensitive circuitry and denser packaging in automation
systems. Available in series, shunt or relay configurations.
[18.34]
.722
[33.78]
1.330
[7.14]
.281
[16.76
±1.14]
.660±.045
[49.28]
1.940
[20.19]
.795
RELAY
DUAL COIL
Relay and Dual Coil
Notes:
Tolerance ± .015 [.39] unless noted. Dimensions in brackets [ ] are millimeters.
A Terminal protrusion dimensions are referenced from back of mounting panel.
B Each screw terminal is supplied with a 10-32x.312[7.92] or M5 x 8mm screw,
flatwasher and external tooth lockwasher.
C Stud terminals are supplied with a flatwasher, external tooth lockwasher and
a 10-32 or M5 hex nut (<=70A), 1/4 -20 or M6 hex nut (>70A).
RELAY
DUAL COIL
Barriers
[69.60]
2.740
[17.02]
.670 [27.89]
1.098
[65.02]
2.560
[29.13]
1.147
[18.31]
.721
[65.02]
2.560
[29.13]
1.147
[18.31]
.721 [.84]
.033
[78.74]
3.100
[35.00]
1.378
[24.18]
.952 [7.69]
.303
[3.11]
.122
[.84]
.033
NOTE:
THIS BARRIER CAN BE FLIPPED
TO COVER EITHER POLE.
PLEASE CONTACT FACTORY FOR
SPECIFIC PART NUMBER
FIG.4FIG.3
FIG.2
FIG.1
CONFIGURATIONS (CONT.)
BARRIER OPTIONS
Rating Option Standard
Barrier
Optional
Barrier
IEL
240/415 VAC
Fig. 1 Fig. 2, 3 & 4
415 VAC (VDE)
277/480 VAC
1/4-20, M6 studs for AC
120/240 VAC multi-pole Fig. 2 Fig. 3 & 4
125VDC
LEL
All multi-pole 50/60 Hz Fig. 2 Fig. 3 & 4
All multi-pole 80 VDC, if opposite polarity Fig. 2 Fig. 3 & 4
125VDC Fig. 2 Fig. 3 & 4
Note: Optional barrier available with factory assigned part number. Contact
factory for assistance.
IAL Series - Congurations http://airpax.sensata.com
141
Mid-Trip Indication
Circuit protection, rapid fault location
and alarm capability are blended
together in the Airpax mid-trip
indication option. This option is
designed for automatic handle
movement to a middle position upon
electrical overload, allowing for easier
detection of the fault circuitand
minimizing downtime due to the
overload condition.
In the optional auxiliary switch
configuration, the switch allows an
alarm or signal to be forwarded when
the breaker trips and the handle
moves to the middle position. The
alarm can be disengaged by the
manual actuation of the handle to the
OFF position. Once the fault has been
corrected, the circuit breaker can be
reset to the ON position. The mid-trip
option is available in one, two or three
pole toggle handle packages and in
either standard panel screw or snap-in
mounting. Please see specification
tables of specific product for available
ratings.
Snap-In Mounting
The snap-in mounting adapter allows for
simplified mounting of most IEL/LEL
toggle handle products. Prior to
shipment, the adapter is attached to the
circuit breaker during our final product
assembly, allowing you to securely snap
the unit into a rectangular panel cut-out.
This eliminates the need for panel
mounting hardware and associated
assembly costs.
Available for units up to three poles,
with or without an option handle
guard.
C
NO
NC
C
NO
NC
BREAKER IN ON
OR MANUALLY
TURNED OFF
POSITION
BREAKER IN
MID-TRIP
POSITION
(ELECTRICALLY
TRIPPED)
ON
POSITION
OFF
POSITION
MID-TRIP
POSITION
(SEE TABLE)
[74.63 ±.18]
2.938±.007
DIM.ìAî
[52.35]
2.061
[25.27]
.995
[81.79]
3.220
[44.45]
1.750
[63.37]
2.495
[17.45]
.687
[39.62]
1.560
Mid-Trip Handle
Positions
Panel Mounting
Detail
Note: Tolerance ± .015 [.39] unless noted.
Dimensions in brackets [ ] are millimeters.
PANEL MOUNTING OPTIONS
# of Poles Dimension “A” Panel Thickness
1 pole .760 ± .007
[19.30 ± .18]
.062 ± .005
[1.57 ± .13]
2 pole 1.530 ± .007
[38.86 ± .18]
.062 ± .005
[1.57 ± .13]
3 pole 2.280 ± .007
[57.91 ± .18]
.062 ± .005
[1.57 ± .13]
Panel Mounting Detail
Tolerance ±.005 [.13] unless noted.
IAL Series - Congurations
IAL Series
142
http://airpax.sensata.com/
IAL/CEL/LEL Series - Operating Characteristics
149
OPERATING CHARACTERISTICS
NOMINAL DCR /IMPEDANCE
Current Ratings
(Amps)
Resistance (ohms) Impedance (ohms) Impedance (ohms)
DC Delays AC, 50/60Hz Delays AC, 400Hz Delays
51, 52, 53, 59 61, 62, 63, 69 41, 42, 43, 49
0.20 45.8 28.5 71.94
1.0 1.38 1.10 2.85
2.0 0.371 0.29 0.76
5.0 0.055 0.051 0.12
10.0 0.017 0.016 0.032
20.0 0.006 0.006 0.010
30.0 0.003 0.004 0.006
50.0 0.0019 0.0018 0.0019
60.0 0.00157 0.00134
70.0 0.00147 0.00133
80.0 0.00146 0.00123
90.0 0.00135 0.00114
100.0 0.00135 0.00114
125.0 0.0005
150.0** 0.0005
165.0** 0.0004
175.0** 0.0004
200.0** 0.0004
250.0** 0.0004
400** 0.0003
Notes:
DCR and impedance based on 100% rated current applied and stablized a minimum of one hour.
No 53 delay on 125 amp single pole or 400 amp four pole devices
Tolerance: .02 amperes to 2.5 amperes, ± 20%; 2.6 amperes to 20 amperes, ± 25%; 21 amperes to 50 amperes, ± 50%. Consult factory for special values and for coil
impedance of delays not shown
** Paralleled poles only, 400 amps only available on CELHP
IAL Series - Operating Characteristics http://airpax.sensata.com
143
http://airpax.sensata.com/ IAL/CEL/LEL Series - Operating Characteristics 150
PERCENTAGE OF RATED CURRENT VS TRIP TIME IN SECONDS AT +25°C
Delay 100% 125%* 150% 200% 400% 600% 800% 1000%
41* No Trip May trip .5 to 8 .15 to 1.9 .02 to .4 .006 to .25 .004 to .1 .004 to .05
42* No Trip May trip 5 to 70 2.2 to 25 .40 to 5 .012 to 2 .006 to .2 .006 to .15
43* No Trip May trip 35 to 350 12 to 120 1.5 to 20 .012 to 2.2 .01 to .22 .01 to .1
49* No Trip May trip .100 max. .050 max. .020 max. .020 max. .020 max. .020 max.
51 No Trip .5 to 6.5 .3 to 3 .1 to 1.2 .031 to .5 .011 to .25 .004 to .1 .004 to .08
52 No Trip 2 to 60 1.8 to 30 1 to 10 .15 to 2 .04 to 1 .008 to .5 .006 to .1
53** No Trip 80 to 700 40 to 400 15 to 150 2 to 20 .23 to 9 .015 to .55 .012 to .2
59 No Trip .120 max. .100 max. .050 max. .022 max. .017 max. .017 max. .017 max.
61 No Trip .7 to 12 .35 to 7 .130 to 3 .030 to 1 .015 to .3 .01 to .15 .008 to .1
62 No Trip 10 to 120 6 to 60 2 to 20 .2 to 3 .02 to 2 .015 to .8 .01 to .25
63 No Trip 50 to 700 30 to 400 10 to 150 1.5 to 20 .4 to 10 .013 to .85 .013 to .5
69 No Trip .120 max .100 max. .050 max. .022 max. .017 max. .017 max. .017 max
71 No Trip .44 to 10 .3 to 7 .100 to 3 .030 to 1 .012 to .3 .004 to .15 .004 to .1
72 No Trip 1.8 to 100 1.7 to 60 1 to 20 .15 to 3 .015 to 2 .008 to .79 .006 to .28
73 No Trip 50 to 600 30 to 400 10 to 150 1.8 to 20 .015 to 10 .015 to .88 .011 to .5
79 No Trip .120 max .100 max. .050 max. .023 max. .016 max. .015 max. .015 max
Notes:
All trip curves and trip currents are specified with the protector mounted in the normal vertical position at ambient temperature of +25° C. Protectors do not carry
current prior to application of overload. A: Ratings above 30 amps may deviate from the above limits by approximately 10% (130% for delay 49).
* No 53 delay on 125 amp single pole or 400 amp four pole devices
* 135% for delay 71, 72, 73 & 79
IAL Series - Operating Characteristics
IAL Series
144
800
700
600
500
400
300
200
150
125
100
0
TIME IN SECONDS
10
1
.1
1000
100
.01
10000
.001
PERCENT OF RATED CURRENT
1000
900
DELAY 61
MAY TRIP
800
700
600
500
400
300
200
150
125
100
0
TIME IN SECONDS
10
1
.1
1000
100
.01
10000
.001
PERCENT OF RATED CURRENT
1000
900
DELAY 62DELAY 62DELAY 62
MAY TRIP
800
700
600
500
400
300
200
150
125
100
0
TIME IN SECONDS
10
1
.1
1000
100
.01
10000
.001
PERCENT OF RATED CURRENT
1000
900
DELAY 63
MAY TRIP
800
700
600
500
400
300
200
150
125
100
0
TIME IN SECONDS
10
1
.1
1000
100
.01
10000
.001
PERCENT OF RATED CURRENT
1000
900
DELAY 69
MAY TRIP
400Hz, DC, 50/60Hz Delay Curves (typ)
A choice of delays is offered for DC, 50/60Hz, 400Hz, or
combined DC/50/60Hz applications. Delays 49, 59, 69
and 79 provide fast-acting, instantaneous tripping and
are often used to protect sensitive electronic
equipment (not recommended where a known inrush
exists). Delays 41, 51, 61 and 71 have a short delay for
general purpose applications. Delays 42, 52, 62 and 72
are long enough for most transformers and capacitor
loads. Delays 43, 53, 63 and 73 are extra long for
special motor applications.
Inrush Pulse Tolerance
Pulse tolerance is defined as a single pulse of half sine wave
peak current amplitude of 8 milliseconds duration that will
not trip the circuit breaker.
The table on page 171 provides a guide to determine if the
inertia delay feature is required. Consult factory for further
assistance.
800
700
600
500
400
300
200
150
125
100
0
TIME IN SECONDS
10
1
.1
1000
100
.01
10000
.001
PERCENT OF RATED CURRENT
1000
900
DELAY 61
MAY TRIP
800
700
600
500
400
300
200
150
125
100
0
TIME IN SECONDS
10
1
.1
1000
100
.01
10000
.001
PERCENT OF RATED CURRENT
1000
900
DELAY 62DELAY 62DELAY 62
MAY TRIP
800
700
600
500
400
300
200
150
125
100
0
TIME IN SECONDS
10
1
.1
1000
100
.01
10000
.001
PERCENT OF RATED CURRENT
1000
900
DELAY 63
MAY TRIP
800
700
600
500
400
300
200
150
125
100
0
TIME IN SECONDS
10
1
.1
1000
100
.01
10000
.001
PERCENT OF RATED CURRENT
1000
900
DELAY 69
MAY TRIP
DELAY CURVES
http://airpax.sensata.com/
IAL/CEL/LEL Series - Operating Characteristics
149 IAL Series - Delay Curves http://airpax.sensata.com
145
DC Delay Curves (typ)
800
700
600
500
400
300
200
150
125
100
0
10
1
.1
1000
100
.01
10000
.001
PERCENT OF RATED CURRENT
1000
900
DELAY 51
MAY TRIP
800
700
600
500
400
300
200
150
125
100
0
TIME IN SECONDS
10
1
.1
1000
100
.01
10000
.001
PERCENT OF RATED CURRENT
1000
900
DELAY 52
MAY TRIP
800
700
600
500
400
300
200
150
125
100
0
TIME IN SECONDS
10
1
.1
1000
100
.01
10000
.001
PERCENT OF RATED CURRENT
1000
900
DELAY 53
MAY TRIP
800
700
600
500
400
300
200
150
125
100
0
TIME IN SECONDS
10
1
.1
1000
100
.01
10000
.001
PERCENT OF RATED CURRENT
1000
900
DELAY 59
MAY TRIP
TIME IN SECONDS
PULSE TOLERANCES
Delay Pulse Tolerance
61, 62, 63, 71, 72, 73 10 times (approx.) rated current
61F, 62F, 63F, 71F, 72F, 73F 12 times (approx.) rated current
64, 65, 66 (0 - 50A) 25 times (approx.) rated current
64, 65, 66 (>50 - 80A) 20 times (approx.) rated current
64, 65, 66 (>80 - 100A) 18 times (approx.) rated current
http://airpax.sensata.com/ IAL/CEL/LEL Series - Operating Characteristics 150
IAL Series - Delay Curves
IAL Series
146
400Hz Delay Curves (typ)
*Available only in IAL/IUL/IEL; not available in LEL.
800
700
600
500
400
300
200
150
125
100
0
10
1
.1
1000
100
.01
10000
.001
PERCENT OF RATED CURRENT
1000
900
DELAY 41
MAY TRIP
800
700
600
500
400
300
200
150
125
100
0
TIME IN SECONDS
10
1
.1
1000
100
.01
10000
.001
PERCENT OF RATED CURRENT
1000
900
DELAY 42
MAY TRIP
800
700
600
500
400
300
200
150
125
100
0
TIME IN SECONDS
10
1
.1
1000
100
.01
10000
.001
PERCENT OF RATED CURRENT
1000
900
DELAY 43
MAY TRIP
800
700
600
500
400
300
200
150
130
100
0
TIME IN SECONDS
10
1
.1
1000
100
.01
10000
.001
PERCENT OF RATED CURRENT
1000
900
DELAY 49
MAY TRIP
TIME IN SECONDS
http://airpax.sensata.com/
IAL/CEL/LEL Series - Operating Characteristics
149 IAL Series - Delay Curves http://airpax.sensata.com
147
DELAY 79
800
700
600
500
400
300
200
150
135
100
0
TIME IN SECONDS
10
1
.1
1000
100
.01
10000
.001
PERCENT OF RATED CURRENT
1000
900
MAY TRIP
800
700
600
500
400
300
200
150
135
100
0
TIME IN SECONDS
10
1
.1
1000
100
.01
10000
.001
PERCENT OF RATED CURRENT
1000
900
DELAY 71
800
700
600
500
400
300
200
150
135
100
0
TIME IN SECONDS
10
1
.1
1000
100
.01
10000
.001
PERCENT OF RATED CURRENT
1000
900
DELAY 73
800
700
600
500
400
300
200
150
135
100
0
TIME IN SECONDS
10
1
.1
1000
100
.01
10000
.001
PERCENT OF RATED CURRENT
1000
900
MAY TRIP
DELAY 72
MAY TRIP MAY TRIP
DC/50/60Hz Dual-frequency Delay Curves (typ)
http://airpax.sensata.com/ IAL/CEL/LEL Series - Operating Characteristics 150
IAL Series - Delay Curves
IAL Series
148
IAL/IUL/IEL/IDL/LEL SPECIFICATIONS
Trip Free
Will trip open on overload even when forcibly held in the ON
position. This prevents the operator from damaging the circuit
by holding the breaker on.
Trip Indication
The operating handle moves positively to the OFF or mid-trip
position on electrical overload.
Ambient Operation
IAL/IUL/IEL protectors operate in temperatures between –40°C
to +85°C.
Insulation Resistance
Not less than 100 megohms at 500 volts DC.
Dielectric Strength
IAL/IUL/IEL protectors withstand 3750Vac (1250Vac for LEL),
60Hz for 60 seconds between all electrically isolated terminals
except auxiliary switch terminals shall withstand 600Vac, 60Hz
for REG and REC types. Four terminal dual coil and relay con-
struction (not offered in the LEL) will withstand 1500Vac.
Endurance
Operating as a switch, the operating life exceeds 10,000 oper-
ations, 6000 at rated load, 4000 without load, at a rate of 6 per
minute.
Electrical Characteristics
.050-100 amperes 80Vdc, 240Vac Max., 240/415Vac at 50
amperes Max., 50/60Hz and 400Hz. Consult factory for specific
product ratings. Units rated for 240/415Vac and above 50
amperes are not suitable for across-the-line motor starting.
Poles
One through six poles available.
Construction
Series, shunt, relay dual coil and series with auxiliary switch
available in various delays and combinations.
Auxiliary Switch
When supplied shall be S.P.D.T. configuration. Non VDE
approved switches have a maximum UL rating of 10.0
amperes, 250 volts, 60Hz; 3.0 amperes, 50 volts DC (REC
type) or 0.1 amperes, 125 volts, 60Hz (REG type).
VDE approved switches have a maximum UL rating of 10.0
amperes, 250 volts, 60Hz (REC type); or 0.1 amperes, 125 volts,
60Hz (REG; type). The maximum VDE ratings are 1.0 amperes, 125
volts, 60Hz (REC type); 0.1 amperes, 125 volts, 60Hz (REG type).
Salt Spray (Corrosion)
Meet the requirements of MIL-PRF-55629 when tested in
accordance with Method 101 of MIL-STD-202.
Moisture Resistance
Meet all the requirements of MIL-PRF-55629 when tested in
accordance with Method 106 of MIL-STD-202.
Shock
Circuit protectors shall not trip when tested per MIL-STD-202,
Method 213, Test Condition I with 100% rated current applied
to delayed units and 80% rated current to instantaneous units.
Vibration
Circuit protectors shall not trip when vibrated per MIL-
STD-202, Method 204, Test Condition A with 100% rated
current applied to delayed units and 80% rated current to
instantaneous units.
UL-1500 (Marine Ignition Protected)
The IDL/IDLH is approved for Marine Ignition Protection (series
configuration only), covering ignition protected circuit break-
ers. This specification requires devices to be used in
accordance with the requirementsof U.S. Coast Guard and Fire
Protection Standard for Pleasure and Commercial Motor Craft,
ANSI/MFPA #302.
APPROXIMATE WEIGHT PER POLE
Ounces Grams
3.1 90
RECOMMENDED TORQUE SPECIFICATIONS
Component Torque (in-lbs)
6-32 Mounting Inserts 6 to 8
M3 Mounting Screws 4 to 5
10-32 Screw Terminals 14 to 15
M5 Terminal Screws 14 to 15
10-32 Stud Terminals 13 to 14
M5 Stud Terminals 13 to 14
1/4 - 20 Stud Terminals 40 to 45
M6 Stud Terminals 40 to 45
1/2 - 32 Mounting Bushing 30 to 35
Where applicable, mechanical support must be provide to the
terminals when applying torque
http://airpax.sensata.com/
IAL/CEL/LEL Series - Operating Characteristics
149 IAL Series - Specications http://airpax.sensata.com
149
AGENCY APPROVALS - IAL/IUL/IEL
Voltage
Frequency
(Hz) Phase
Min.
Poles TC OL UL/CSA
VDE
(amps)
UL 1077 & CSA
(AIC)
VDE
(AIC)
65 DC - 1 1 1 .02-100 .10-70 U2, 7500 4000
65(4) DC - 1 1 1 .02-100 - U2, 3000 -
65(4) DC - 1 1 1 .02-50 - U2, 5000 -
65 DC - 2** 2 1 101-150 - U2, 7500 -
80 DC - 1 1 1 .02-70 .10-50 U2, 7500 4000
80 DC - 1 1 1 70.1-100 - U2, 5000 -
80 DC - 2 1 1 101-150 - U1, 10000 -
80 DC - 3 1 0 251-300 - U2, 7500 -
125 DC - 2 1 0 .02-100 - U2, 5000 -
250 DC - 2+ 1 0 .02-50 - U1, 5000 -
300 DC - 3++ 1 0 .02-50 .10-50 U2, 1000 5000
125 50/60 1 1 1 0 .02-70 - U2, 5000 -
125 50/60 1 1 1 1 .02-100 - U1, 3000 -
125(5) 50/60 1 1 1 1 .02-100 - U3, 1500 -
120/240 50/60 1 2 2 1 .02-100 - U1, 2000 -
125/250(5) 50/60 1 2 only 1 1 .02-100 - U3, 1500 -
240 50/60 1&3 1 1 0 .02-70 - U1, 2000 -
240 50/60 3 2 1 1 .02-100 - U2, 2000 -
250 50/60 3 1 1 1 .02-50 .10-100 U2, 3000 2000
250 50/60 3 1 1 1 .02-50 .10-100 C2, 5000(1) 2000
250 50/60 1 1 1 1 .02-50 .10-100 C2, 5000(2) 2000
250 50/60 3 2 1 0 .02-80 .10-100 U1, 1000 2000
250 50/60 3 1 1 0 .02-60 .10-100 U1, 5000 2000
250(5) 50/60 3 3 only 1 1 .02-100 - U3, 2000 -
277 50/60 1 1 1 1 .02-50 - U2, 2000 -
277 50/60 1&3 1 2 1 .02-50 - C2, 5000(1) -
240/415 50/60 3 2 2 0 .02-50 .10-50 U2, 2000 2000
240/415 50/60 1 2 2 0 .02-50 .10-50 C2, 5000(1) 2000
277/480 50/60 3 2 2 1 .02-30 - U2, 2000 -
277/480 50/60 3 2 2 1 .02-50 - U2, 1200 -
277/480 50/60 3 2 1 1 .02-30 - C2, 5000(3) -
277480 50/60 1&3 2 1 0 .02-50 - C2, 5000(3) -
480 50/60 1&3 2 1 1 .02-30 - C2, 5000(3) -
480 50/60 3 2 1 0 .02-50 - C2, 5000(3) -
250 400 1&3 1 2 1 .02-50 - U2, 1500 -
AGENCY APPROVALS - CEL/CELP (COMMUNICATIONS)
Voltage
Frequency
(Hz) Phase
Min.
Poles UL/CSA
VDE
(amps)
UL 489A
(AIC)
VDE
(AIC)
65 DC - 1 .05-50 - 7500 -
65 DC - 2** 101-150 - 50000 -
80 DC - 1 .05-100 - 50000 -
80 DC - 2** 101-200 - 10000 -
80 DC - 3** 201-250 - 10000 -
125 DC - 1 .05-70 - 5000 -
80 DC - 1 125 - 10000 -
General notes:
• All supplementary protectors are of the overcurrent (OC) type
The family of protectors has been evaluated for end use application for use groups
(UG) A, B, C and D
• The terminals (FW) are suitable for factory wiring only (0)
The maximum voltage ratings for which the protectors have been tested are shown in
the chart
The current is the amperage range that the protectors have been tested
The tripping current (TC) for all of the protectors is either either “1” (in the range of
125% to 135% of ampere rating) or “2” (more than 135% of ampere rating)
The overload rating (OL) – designates whether the protector has been tested for
general use or motor starting applications.
0 – tested at 1.5 times amp rating for general use
1 – tested at 6 times AC rating or 10 times DC rating for motor starting
The short circuit current rating (SC) – The short circuit rating in amperes following a
letter and number designating the test conditions and any calibration following the
short circuit test is defined below:
C – Indicates short circuit test was conducted with series overcurrent protection
U – Indicates short circuit test was conducted without series overcurrent protection
1 – Indicates a recalibration was not conducted as part of the short circuit testing
2 – Indicates a recalibration was performed as part of the short circuit testing
3 – Indicates recalibration was performed along with the dielectric and voltage
withstand for “Suitable for Further Use” rating
AGENCY APPROVALS - IULD (DUST SEALED)
Voltage
Frequency
(Hz) Phase
Min.
Poles TC OL UL/CSA
VDE
(amps)
UL 1077 & CSA
(AIC)
VDE
(AIC)
250 50/60 1&3 1 1 1 .02-100 - C2, 5000(3) -
277 50/60 1 1 1 1 .02-30 - C2, 5000(3) -
Notes:
** Paralleled poles; + 2 poles in series; ++ 3 poles in series; (1) With 125 A max. series fuse; (2) Series
combination with 209 or 229 series (100 A max.); (3) With 100 A max. series fuse; (4) With blocked vent
construction (5) Non-standard construction. “Fit for further use” approval
IAL/IUL/IEL/IDL/LEL/LELHP SPECIFICATIONS
AGENCY APPROVALS - LEL/LELHP
Voltage
Frequency
(Hz) Phase
Min.
Poles UL/CSA
VDE
(amps)
UL489
(AIC)
VDE
(AIC)
65 DC - 1 .05-50 - 7500 -
65 DC - 2** 101-150 - 50 000 -
65 DC - 3** 175-200 - 50000 -
80 DC - 1 .05-100 .10-100 10000 2000
80 DC - 1 .05-100 - 50000 -
80 DC - 2** 125-150 125-150 10000 2000
80 DC - 3** 175-200 151-200 10000 2000
125 DC - 1 .05-70 .05-70 5000 3000
125/250 DC - 2 .05-50 - 5000 -
125 50/60 1&3 1 .05-40 - 10000 -
125 50/60 1&3 1 .05-50 .10-50 5000 2000
120/240 50/60 1 2 .05-70 .10-50 5000 2000
240 50/60 1&3 1 .05-20 - 5000 -
AGENCY APPROVALS - CELHP
80 DC - 4 400 - 10000 AIC
(UL489A)
-
AGENCY APPROVALS - IDL/IDLP (MARINE)
Voltage
Frequency
(Hz) Phase
Min.
Poles TC OL UL/CSA
VDE
(amps)
UL 1077 & CSA
(AIC)
VDE
(AIC)
48 DC - 1 1 1 .02-100 - U1, 5000 -
48 DC - 2** 1 1 101-150 - U1, 5000 -
65 DC - 1 1 1 .02-60 - U1, 1000 -
80 DC - 1 1 1 .02-100 - U2, 1500 -
125 50/60 1 1 1 1 .02-100 - U 1, 1500 -
250 50/60 1 2 1 1 .02-100 - U2, 1500 -
250 50/60 1&3 1 1 1 .02-60 - U1, 1000 -
AGENCY APPROVALS - IULQ (TAPPED COIL)
Voltage
Frequency
(Hz) Phase
Min.
Poles TC OL UL/CSA
VDE
(amps)
UL 1077 & CSA
(AIC)
VDE
(AIC)
125/250 50/60 1 1 1 1 2/1-30/15 - C2, 5000(1) -
http://airpax.sensata.com/ IAL/CEL/LEL Series - Operating Characteristics 150
IAL Series - Specications
IAL Series
150
IAL/IUL/IEL DECISION TABLES
The ordering code for IAL/IUL/IEL/LEL
circuit protectors may be determined by
following the decision steps in the
appropriate part number decision table
subsequent to this page.
The coding given permits a self-assigning
part number but with certain limitations.
Special applications may require a factory
assigned part number. Typical examples
are units with mixed ratings, combinations
of styles, or constructions not listed in the
third decision table, etc. With these, it is
suggested that order entry be by
description and/or drawings, and a part
number will be established. Additionally, it
is standard policy to establish a factory-
assigned part number whenever a
descriptive drawing exists to provide cross
reference, traceability and manufacturing
control.
When specifying a circuit breaker for AC
motor start or high inrush applications, the
peak amplitude and surge duration should
be specified for factory assistance in rating
selection.
For example the code shown is the code
for a single pole breaker with a series
construction and auxiliary switch,
designed for operation in a 50/60Hz
circuit. It has a short time delay, rating of
20 amperes and a marked black handle,
and is VDE approved.
To determine the ordering number for your
particular IAL/IUL/IEL unit, simply follow
the steps shown. You may use this number
to place an order or as a reference for
further questions you may have.
Notes:
IEL, IELH and IELX circuit protectors are designed
to meet 8mm creepage clearance requirements for
installation Category 111, Pollution Degree 3, Case A as
measured in IEC 664. Intended for use in equipment to
comply with IEC 950, 601 and VDE 0804 & 0805.
Second Decision
Single pole
Two pole
Three pole
Four pole*
1
11
111
1111
2
Poles
*Not available in toggle seal handle type.
Consult factory for 5 and 6 pole IEL part number.
Internal Conguration
Third Decision
3
* Only one auxiliary switch is normally supplied on two or three
pole units. Switch is located in the right-hand pole (viewed from
terminal end) unless otherwise specied.
12 3 4
IEL 1 - 1REC4- 61- 20.0 - 01 - V
57
Example:
Black
Yellow
Red
Blue
Green
Orange
White
-00
-10
-20
-30
-40
-60
-90
-01 (STD)
-11
-21
-31
-41
-61
-91
Seventh Decision
7
Handle Color and Marking Selection
IAL, IUL, IEL, IALH,
IULH, IELH - Toggle Handle
Marked*
ON-OFF
Color Unmarked I-O
Fifth Decision
5
Rated Current
Use three numbers to print required
current value between .10 0 amps
minimum and 100 amps maximum.
For example, use:
.100 or 2.00 or 10.0
The VDE (lth) will be 95% of the
UL/CSA rated current.
Fourth Decision
4
Frequency & Delay
Switch only
400Hz short delay
400Hz long delay
400Hz motor start
400Hz 150% instant trip
DC short delay
DC long delay
DC motor start
DC 125% instant trip
50/60Hz short delay
50/60Hz long delay
50/60Hz motor start
50/60Hz 125% instant trip
DC/60Hz short delay
DC/60Hz long delay
DC/60Hz motor start
DC/60 Hz 135% instant trip
For addition of inertial delay, add an ìFî to any
delay numeral.
SW
-41
-42
-43
-49
-51
-52
-53
-59
-61
-62
-63
-69
-71
-72
-73
-79
Notes: A. Bezels of IALBX, IULBX, IELB, IELBX are black.
B. Consult factory for other marking options.
Note: CCC Approval is pending.
Black
Red
Grey
Orange
White
-00
-20
-40
-50
-90
-01
-21
-41
-51
-91
-02
-22
-42
-52
-92
-03
-23
-43
-53
-93
-04
-24
-44
-54
-94
-05
-25
-45
-55
-95
-06
-26
-46
-56
-96
I-O
Fig.2
Unmarked
Marking
Detail
Seventh Decision
7
Rocker Handle Color, Indicator Color and Marking Selection (See Notes)
IALX, IULX, IELX, IALZX, IULZX, IELZX Rocker Handle (Single Rocker Color)
Rocker
Handle
Color
Indicating
Color
Marking
Color Indicates:
On-Off
Fig.1
On-Off
I-O
Fig.3
On-Off
I-O
Fig.6
I-O
Fig.5
On-Off
Fig.4
A
Vertical Mounting Horizontal Mounting
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Black
Black
Black
White
Red
Green
White
White
White
On
On
On
-J0
-K0
-L0
-J1
-K1
-L1
-J2
-K2
-L2
-J3
-K3
-L3
-J4
-K4
-L4
-J5
-K5
-L5
-J6
-K6
-L6
B
C
White
White
Black
Black
Black
IALZX, IULZX, IELZX Rocker Handle (Dual Rocker Color)
Black
Black
Black
Black
Black
Black
White
Red
Green
White
Red
Green
White
White
White
White
White
White
On
On
On
Off
Off
Off
-A0
-B0
-C0
-F0
-G0
-H0
-A1
-B1
-C1
-F1
-G1
-H1
-A2
-B2
-C2
-F2
-G2
-H2
-A3
-B3
-C3
-F3
-G3
-H3
-A4
-B4
-C4
-F4
-G4
-H4
-A5
-B5
-C5
-F5
-G5
-H5
-A6
-B6
-C6
-F6
-G6
-H6
Black
Black
Black
Black
White
Red
Green
Yellow
White
Red
Green
Yellow
Off
Off
Off
Off
-M0
-N0
-P0
-R0
N/A
N/A
N/A
N/A
-M2
-N2
-P2
-R2
-M3
-N3
-P3
-R3
N/A
N/A
N/A
N/A
-M6
-N6
-P6
-R6
N/A
N/A
N/A
N/A
A
IALBX, IULBX, IELBX, LELBX Rocker Handle (Dual Rocker Color)
IALBX
**IULBX
***IELBX
**IMLBX
One handle per unit
One handle per pole
One handle per unit
panel seal
One handle per unit,
rocker, bracket mounting
One handle per unit,
rocker, integral mounting
One handle per unit
UL 1500
One handle per pole
UL 1500
One handle per unit
mid trip indication
One handle per pole
mid trip indication
One handle per unit,
rocker, accidental-off
protection
One handle per unit,
mid trip indication, rocker,
accidental-off protection
*UL Recognized
**UL Recognized, CSA Certied
***UL Recognized, CSA Certied, VDE Approved
*** IML
*** IMLH
Select Type and Terminal
First Decision
1
IAL
**IUL
***IEL
IALH
**IULH
***IELH
IALN
***IULN
IALX
**IULX
***IELX
IALZX
**IULZX
***IELZX
* IDL
* IDLH
Type Terminal
Standard screw terminal,
no designation required
Stud terminals
Clip terminals
Bullet terminals
K
C
B
Sixth Decision
6
Notes:
1. One or more descriptions may be used as required.
2. When this is not used, table one may be substituted and U.S. thread and
two lockwashers will be supplied. Unit will be rated at 250V (50/60Hz only.)
3. VDE approved at 250Vac
4. VDE approved at 415Vac
-A
-B
-C
-D
-E
-G
-K
-L
-M
-P
-U
-W
-X
-1
-2
Standard hardware. No designation required.
Metric thread mounting inserts and terminals
Barrier
277V (50/60Hz only) (See note 3)
240/415V (50/60Hz only)
277V/480V (50/60Hz only) (See note 4)
Handle guard, (available in ZX, BX and snap-in
versions only)
1/4 - 20 stud (M6 stud when -A option is selected)
(<=70A requires -K, if >70A do not use -K)
Handle lock
Handle in opposite pole
Snap-in face plate adapter
120/240V 50/60Hz
Wire clamp supplied (VDE approved up to
and including 16.0 amps)
Handle guard with no actuation feature
(BX rocker only)
Silver 5/16" (.312") bullet
Gold 5/16" (.312") bullet
Optional
The shaded areas denote VDE and CCC
(if applicable) Approval options. This approval
requires the addition of a V at the end of the
part number. The V will be added to any part
number formed entirely from shaded decisions.
If non-shaded areas are selected, the unit will not
be VDE or CCC Approved, but other approvals
still apply.
V = VDE and CCC Approved
Description
Note: CCC Approval is pending.
-0
-1
-1REC4
-1REC5
-1REG4
-1RS4
-1RLS4
-1RS5
-3
-4
Switch only (50, 70 or 100 amp switch)
Series
Series with auxiliary switch*
.110 quick connect
Series with auxiliary switch*
.187 quick connect
Series with auxiliary switch
.110 quick connect
Series with alarm switch,
electrical trip, .110 quick connect
terminals
Series with alarm switch,
electrical trip, .110 quick connect
terminals (mid-trip only)
Series with alarm switch,
electrical trip, .187 quick connect
terminals
Shunt
Relay (not available in IEL/IELX)
This approval requires the addition of a C at the end
of the part number. The unit will not be VDE Approved.
C = CCC Approved
IAL Series - Decision Tables http://airpax.sensata.com
151
Second Decision
Single pole
Two pole
Three pole
Four pole*
1
11
111
1111
2
Poles
*Not available in toggle seal handle type.
Consult factory for 5 and 6 pole IEL part number.
Internal Conguration
Third Decision
3
* Only one auxiliary switch is normally supplied on two or three
pole units. Switch is located in the right-hand pole (viewed from
terminal end) unless otherwise specied.
12 3 4
IEL 1 - 1REC4- 61- 20.0 - 01 - V
57
Example:
Black
Yellow
Red
Blue
Green
Orange
White
-00
-10
-20
-30
-40
-60
-90
-01 (STD)
-11
-21
-31
-41
-61
-91
Seventh Decision
7
Handle Color and Marking Selection
IAL, IUL, IEL, IALH,
IULH, IELH - Toggle Handle
Marked*
ON-OFF
Color Unmarked I-O
Fifth Decision
5
Rated Current
Use three numbers to print required
current value between .10 0 amps
minimum and 100 amps maximum.
For example, use:
.100 or 2.00 or 10.0
The VDE (lth) will be 95% of the
UL/CSA rated current.
Fourth Decision
4
Frequency & Delay
Switch only
400Hz short delay
400Hz long delay
400Hz motor start
400Hz 150% instant trip
DC short delay
DC long delay
DC motor start
DC 125% instant trip
50/60Hz short delay
50/60Hz long delay
50/60Hz motor start
50/60Hz 125% instant trip
DC/60Hz short delay
DC/60Hz long delay
DC/60Hz motor start
DC/60 Hz 135% instant trip
For addition of inertial delay, add an ìFî to any
delay numeral.
SW
-41
-42
-43
-49
-51
-52
-53
-59
-61
-62
-63
-69
-71
-72
-73
-79
Notes: A. Bezels of IALBX, IULBX, IELB, IELBX are black.
B. Consult factory for other marking options.
Note: CCC Approval is pending.
Black
Red
Grey
Orange
White
-00
-20
-40
-50
-90
-01
-21
-41
-51
-91
-02
-22
-42
-52
-92
-03
-23
-43
-53
-93
-04
-24
-44
-54
-94
-05
-25
-45
-55
-95
-06
-26
-46
-56
-96
I-O
Fig.2
Unmarked
Marking
Detail
Seventh Decision
7
Rocker Handle Color, Indicator Color and Marking Selection (See Notes)
IALX, IULX, IELX, IALZX, IULZX, IELZX Rocker Handle (Single Rocker Color)
Rocker
Handle
Color
Indicating
Color
Marking
Color Indicates:
On-Off
Fig.1
On-Off
I-O
Fig.3
On-Off
I-O
Fig.6
I-O
Fig.5
On-Off
Fig.4
A
Vertical Mounting Horizontal Mounting
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Black
Black
Black
White
Red
Green
White
White
White
On
On
On
-J0
-K0
-L0
-J1
-K1
-L1
-J2
-K2
-L2
-J3
-K3
-L3
-J4
-K4
-L4
-J5
-K5
-L5
-J6
-K6
-L6
B
C
White
White
Black
Black
Black
IALZX, IULZX, IELZX Rocker Handle (Dual Rocker Color)
Black
Black
Black
Black
Black
Black
White
Red
Green
White
Red
Green
White
White
White
White
White
White
On
On
On
Off
Off
Off
-A0
-B0
-C0
-F0
-G0
-H0
-A1
-B1
-C1
-F1
-G1
-H1
-A2
-B2
-C2
-F2
-G2
-H2
-A3
-B3
-C3
-F3
-G3
-H3
-A4
-B4
-C4
-F4
-G4
-H4
-A5
-B5
-C5
-F5
-G5
-H5
-A6
-B6
-C6
-F6
-G6
-H6
Black
Black
Black
Black
White
Red
Green
Yellow
White
Red
Green
Yellow
Off
Off
Off
Off
-M0
-N0
-P0
-R0
N/A
N/A
N/A
N/A
-M2
-N2
-P2
-R2
-M3
-N3
-P3
-R3
N/A
N/A
N/A
N/A
-M6
-N6
-P6
-R6
N/A
N/A
N/A
N/A
A
IALBX, IULBX, IELBX, LELBX Rocker Handle (Dual Rocker Color)
IALBX
**IULBX
***IELBX
**IMLBX
One handle per unit
One handle per pole
One handle per unit
panel seal
One handle per unit,
rocker, bracket mounting
One handle per unit,
rocker, integral mounting
One handle per unit
UL 1500
One handle per pole
UL 1500
One handle per unit
mid trip indication
One handle per pole
mid trip indication
One handle per unit,
rocker, accidental-off
protection
One handle per unit,
mid trip indication, rocker,
accidental-off protection
*UL Recognized
**UL Recognized, CSA Certied
***UL Recognized, CSA Certied, VDE Approved
*** IML
*** IMLH
Select Type and Terminal
First Decision
1
IAL
**IUL
***IEL
IALH
**IULH
***IELH
IALN
***IULN
IALX
**IULX
***IELX
IALZX
**IULZX
***IELZX
* IDL
* IDLH
Type Terminal
Standard screw terminal,
no designation required
Stud terminals
Clip terminals
Bullet terminals
K
C
B
Sixth Decision
6
Notes:
1. One or more descriptions may be used as required.
2. When this is not used, table one may be substituted and U.S. thread and
two lockwashers will be supplied. Unit will be rated at 250V (50/60Hz only.)
3. VDE approved at 250Vac
4. VDE approved at 415Vac
-A
-B
-C
-D
-E
-G
-K
-L
-M
-P
-U
-W
-X
-1
-2
Standard hardware. No designation required.
Metric thread mounting inserts and terminals
Barrier
277V (50/60Hz only) (See note 3)
240/415V (50/60Hz only)
277V/480V (50/60Hz only) (See note 4)
Handle guard, (available in ZX, BX and snap-in
versions only)
1/4 - 20 stud (M6 stud when -A option is selected)
(<=70A requires -K, if >70A do not use -K)
Handle lock
Handle in opposite pole
Snap-in face plate adapter
120/240V 50/60Hz
Wire clamp supplied (VDE approved up to
and including 16.0 amps)
Handle guard with no actuation feature
(BX rocker only)
Silver 5/16" (.312") bullet
Gold 5/16" (.312") bullet
Optional
The shaded areas denote VDE and CCC
(if applicable) Approval options. This approval
requires the addition of a V at the end of the
part number. The V will be added to any part
number formed entirely from shaded decisions.
If non-shaded areas are selected, the unit will not
be VDE or CCC Approved, but other approvals
still apply.
V = VDE and CCC Approved
Description
Note: CCC Approval is pending.
-0
-1
-1REC4
-1REC5
-1REG4
-1RS4
-1RLS4
-1RS5
-3
-4
Switch only (50, 70 or 100 amp switch)
Series
Series with auxiliary switch*
.110 quick connect
Series with auxiliary switch*
.187 quick connect
Series with auxiliary switch
.110 quick connect
Series with alarm switch,
electrical trip, .110 quick connect
terminals
Series with alarm switch,
electrical trip, .110 quick connect
terminals (mid-trip only)
Series with alarm switch,
electrical trip, .187 quick connect
terminals
Shunt
Relay (not available in IEL/IELX)
This approval requires the addition of a C at the end
of the part number. The unit will not be VDE Approved.
C = CCC Approved
MARKING DETAIL “A” (SEE TABLE)
LOAD LOAD
LINE
LOAD LOAD
LINE LINELINE
FIG. 2 FIG. 3 FIG. 4 FIG. 5
FIG. 1 FIG. 6
OFFON
ON
OFF
OFFON
ON
OFF
OO
O
O
LINE LINE
ROCKER
HANDLE
COLOR
INDICATING
COLOR
INDICATING
COLOR
ROCKER
HANDLE
COLOR
INDICATION “ON”
Mounting/Indicator Code: A, B, C
INDICATION “OFF”
Mounting/Indicator Code: F, G, H
ON
I
ON
I
O
OFF
OFF
O
INDICATION “OFF”
Mounting/Indicator Code: M, N, P, R
MARKING DETAIL “C” (SEE TABLE)
FIG. 2 FIG. 3 FIG. 6
LINE
LOAD LOAD
LINE
O
OFF ON
O
O
ON
OFF
MARKING DETAIL “B” (SEE TABLE)
FIG. 2 FIG. 3 FIG. 4 FIG. 5
FIG. 1 FIG. 6
OFFON
ON
OFF
OFFON
ON
OFF
OO
O
O
LINE
LOAD
LOAD LINE LOAD LINE LOAD LINE
LINE
ROCKER
HANDLE
COLOR
INDICATING
COLOR
ON
I
INDICATION “ON”
Mounting/Indicator Code: J, K, L
OFF
O
LINE
Second Decision
Single pole
Two pole
Three pole
Four pole*
1
11
111
1111
2
Poles
*Not available in toggle seal handle type.
Consult factory for 5 and 6 pole IEL part number.
Internal Conguration
Third Decision
3
* Only one auxiliary switch is normally supplied on two or three
pole units. Switch is located in the right-hand pole (viewed from
terminal end) unless otherwise specied.
12 3 4
IEL 1 - 1REC4- 61- 20.0 - 01 - V
57
Example:
Black
Yellow
Red
Blue
Green
Orange
White
-00
-10
-20
-30
-40
-60
-90
-01 (STD)
-11
-21
-31
-41
-61
-91
Seventh Decision
7
Handle Color and Marking Selection
IAL, IUL, IEL, IALH,
IULH, IELH - Toggle Handle
Marked*
ON-OFF
Color Unmarked I-O
Fifth Decision
5
Rated Current
Use three numbers to print required
current value between .10 0 amps
minimum and 100 amps maximum.
For example, use:
.100 or 2.00 or 10.0
The VDE (lth) will be 95% of the
UL/CSA rated current.
Fourth Decision
4
Frequency & Delay
Switch only
400Hz short delay
400Hz long delay
400Hz motor start
400Hz 150% instant trip
DC short delay
DC long delay
DC motor start
DC 125% instant trip
50/60Hz short delay
50/60Hz long delay
50/60Hz motor start
50/60Hz 125% instant trip
DC/60Hz short delay
DC/60Hz long delay
DC/60Hz motor start
DC/60 Hz 135% instant trip
For addition of inertial delay, add an ìFî to any
delay numeral.
SW
-41
-42
-43
-49
-51
-52
-53
-59
-61
-62
-63
-69
-71
-72
-73
-79
Notes: A. Bezels of IALBX, IULBX, IELB, IELBX are black.
B. Consult factory for other marking options.
Note: CCC Approval is pending.
Black
Red
Grey
Orange
White
-00
-20
-40
-50
-90
-01
-21
-41
-51
-91
-02
-22
-42
-52
-92
-03
-23
-43
-53
-93
-04
-24
-44
-54
-94
-05
-25
-45
-55
-95
-06
-26
-46
-56
-96
I-O
Fig.2
Unmarked
Marking
Detail
Seventh Decision
7
Rocker Handle Color, Indicator Color and Marking Selection (See Notes)
IALX, IULX, IELX, IALZX, IULZX, IELZX Rocker Handle (Single Rocker Color)
Rocker
Handle
Color
Indicating
Color
Marking
Color Indicates:
On-Off
Fig.1
On-Off
I-O
Fig.3
On-Off
I-O
Fig.6
I-O
Fig.5
On-Off
Fig.4
A
Vertical Mounting Horizontal Mounting
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Black
Black
Black
White
Red
Green
White
White
White
On
On
On
-J0
-K0
-L0
-J1
-K1
-L1
-J2
-K2
-L2
-J3
-K3
-L3
-J4
-K4
-L4
-J5
-K5
-L5
-J6
-K6
-L6
B
C
White
White
Black
Black
Black
IALZX, IULZX, IELZX Rocker Handle (Dual Rocker Color)
Black
Black
Black
Black
Black
Black
White
Red
Green
White
Red
Green
White
White
White
White
White
White
On
On
On
Off
Off
Off
-A0
-B0
-C0
-F0
-G0
-H0
-A1
-B1
-C1
-F1
-G1
-H1
-A2
-B2
-C2
-F2
-G2
-H2
-A3
-B3
-C3
-F3
-G3
-H3
-A4
-B4
-C4
-F4
-G4
-H4
-A5
-B5
-C5
-F5
-G5
-H5
-A6
-B6
-C6
-F6
-G6
-H6
Black
Black
Black
Black
White
Red
Green
Yellow
White
Red
Green
Yellow
Off
Off
Off
Off
-M0
-N0
-P0
-R0
N/A
N/A
N/A
N/A
-M2
-N2
-P2
-R2
-M3
-N3
-P3
-R3
N/A
N/A
N/A
N/A
-M6
-N6
-P6
-R6
N/A
N/A
N/A
N/A
A
IALBX, IULBX, IELBX, LELBX Rocker Handle (Dual Rocker Color)
IALBX
**IULBX
***IELBX
**IMLBX
One handle per unit
One handle per pole
One handle per unit
panel seal
One handle per unit,
rocker, bracket mounting
One handle per unit,
rocker, integral mounting
One handle per unit
UL 1500
One handle per pole
UL 1500
One handle per unit
mid trip indication
One handle per pole
mid trip indication
One handle per unit,
rocker, accidental-off
protection
One handle per unit,
mid trip indication, rocker,
accidental-off protection
*UL Recognized
**UL Recognized, CSA Certied
***UL Recognized, CSA Certied, VDE Approved
*** IML
*** IMLH
Select Type and Terminal
First Decision
1
IAL
**IUL
***IEL
IALH
**IULH
***IELH
IALN
***IULN
IALX
**IULX
***IELX
IALZX
**IULZX
***IELZX
* IDL
* IDLH
Type Terminal
Standard screw terminal,
no designation required
Stud terminals
Clip terminals
Bullet terminals
K
C
B
Sixth Decision
6
Notes:
1. One or more descriptions may be used as required.
2. When this is not used, table one may be substituted and U.S. thread and
two lockwashers will be supplied. Unit will be rated at 250V (50/60Hz only.)
3. VDE approved at 250Vac
4. VDE approved at 415Vac
-A
-B
-C
-D
-E
-G
-K
-L
-M
-P
-U
-W
-X
-1
-2
Standard hardware. No designation required.
Metric thread mounting inserts and terminals
Barrier
277V (50/60Hz only) (See note 3)
240/415V (50/60Hz only)
277V/480V (50/60Hz only) (See note 4)
Handle guard, (available in ZX, BX and snap-in
versions only)
1/4 - 20 stud (M6 stud when -A option is selected)
(<=70A requires -K, if >70A do not use -K)
Handle lock
Handle in opposite pole
Snap-in face plate adapter
120/240V 50/60Hz
Wire clamp supplied (VDE approved up to
and including 16.0 amps)
Handle guard with no actuation feature
(BX rocker only)
Silver 5/16" (.312") bullet
Gold 5/16" (.312") bullet
Optional
The shaded areas denote VDE and CCC
(if applicable) Approval options. This approval
requires the addition of a V at the end of the
part number. The V will be added to any part
number formed entirely from shaded decisions.
If non-shaded areas are selected, the unit will not
be VDE or CCC Approved, but other approvals
still apply.
V = VDE and CCC Approved
Description
Note: CCC Approval is pending.
-0
-1
-1REC4
-1REC5
-1REG4
-1RS4
-1RLS4
-1RS5
-3
-4
Switch only (50, 70 or 100 amp switch)
Series
Series with auxiliary switch*
.110 quick connect
Series with auxiliary switch*
.187 quick connect
Series with auxiliary switch
.110 quick connect
Series with alarm switch,
electrical trip, .110 quick connect
terminals
Series with alarm switch,
electrical trip, .110 quick connect
terminals (mid-trip only)
Series with alarm switch,
electrical trip, .187 quick connect
terminals
Shunt
Relay (not available in IEL/IELX)
This approval requires the addition of a C at the end
of the part number. The unit will not be VDE Approved.
C = CCC Approved
IAL Series
Second Decision
Single pole
Two pole
Three pole
1
11
111
2
Poles
Fifth Decision
5
Rated Current
Use three numbers to print (.050 or 1.50 or 100)
Value between .050 amps and 10 0 amps.
Fourth Decision
4
Frequency and Delay
DC short delay
DC long delay
DC motor start
DC 125% instant trip
50/60Hz short delay
50/60Hz long delay
50/60Hz motor start
50/60Hz 125% instant trip
For addition of inertial delay, add an “F” to any
delay numeral.
*Not available above 100 amps.
-51
-52
-53*
-59
-61
-62
-63
-69
The shaded areas denote VDE and CCC (if applicable)
Approval options. This approval requires the addition of
a V at the end of the part number. The V will be added to
any part number formed entirely from shaded decisions.
If non-shaded areas are selected, the unit will not be
VDE or CCC Approved, but other approvals still apply.
V = VDE and CCC Approved
The approval requires the addition of a C at the end
of the part number. The unit will not be VDE Approved.
C = CCC Approved
12 3 4
LEL 1 - 1REC4 - 61 - 20.0 - 01 - V
57
Example:
Third Decision
3
* Used only with mid-trip.
-1
-1REC4
-1REC5
-1REG4
-1RS4
-1RLS4
Series
Series with auxiliary switch
.110 quick connect
Series with auxiliary switch
.187 quick connect
Series with auxiliary switch
(gold contacts)
.110 quick connect
Series with alarm switch,
electrical trip,
.110 quick connect
Series with alarm switch,
electrical trip,
.110 quick connect*
Internal Conguration
Note: Other options available, consult factory.
One handle per unit
One handle per pole
One handle per unit, mid-trip
indication
One handle per pole, mid-trip
indication
One handle per unit, rocker,
integral mounting
One handle per unit, rocker,
mid-trip indication, integral mounting
One handle per unit, rocker,
accidental-off protected
One handle per unit, rocker,
mid-trip indication, accidental-off
protected
LEL
LELH
LML
LMLH
LELZX
LMLZX
LELBX
LMLBX
Select Type and Terminal
First Decision
1
Type Terminal
Standard screw terminal,
no designation required
Stud terminals
Clip terminals
Bullet terminals
K
C
B
Description
Sixth Decision
Metric thread mounting inserts
and terminals
Barrier
240V 50/60Hz
Handle guard, (available in ZX, BX and
snap-in versions only)
1/4
- 20 Stud (M6 Stud when -A
option is selected) ( 50A requires -K,
>50A do not use -K)
Handle Lock
Handle in opposite pole
Snap-in mounting plate adapter
120/240Vac, 5000 A.I.C., 70A max.
2 pole only with barrier (VDE 250Vac)
125VDC
Handle guard with no actuate
"off" feature (see detail C)
Silver 5/16" (.312") bullet
Gold 5/16" (.312") bullet
-A
-B
-F
-G
-K
-L
-M
-P
-U
-V
-X
-1
-2
6
Optional
Notes:
1. One or more descriptions may be used as required.
2. When this decision is not used, decision 7 may be
substituted and U.S. thread will be supplied.
3.If (M5 or M6) studs are required, use A” only on an LELK.
Seventh Decision
7
LEL Toggle Handle Color Selection
Black w/ white markings
Yellow w/ black markings
Red w/ white markings
Blue w/ white markings
Green w/ white markings
Orange w/ black markings
White w/ black markings
-01
-11
-21
-31
-41
-61
-91
See alternate 7th Decision for ZX and BX Rocker
Handles.
LEL DECISION TABLES
http://airpax.sensata.com/
IAL/CEL/LEL Series - Operating Characteristics
149 LEL Series - Decision Tables http://airpax.sensata.com
153
Notes: The LEL family of circuit breakers are designed
to meet 8mm creepage and clearance requirements for
installation Category 111, pollution degree 3, Case A as
measured in IEC 664. Intended for use in equipment designed
to comply with IEC 380, 435, 601 AND VDE 0730, 0804 & 0805.
LINE LINE
FIG. 2 FIG. 3 FIG. 4 FIG. 5
FIG. 1 FIG. 6
ROCKER HANDLE
COLOR
INDICATING COLOR
INDICATING
COLOR
ROCKER HANDLE
COLOR
INDICATION “ON”
Mounting/Indicator Code: A, B, C
LOAD LOAD
LINE
LOAD LOAD
LINE
INDICATION “OFF”
Mounting/Indicator Code: F, G, H
LINELINE
Area reserved for
amperage marking.
ON
I
ON
I
O
OFF
OFF
O
OFF ON
ON
OFF
O
OFF ON
OO
O
ON
OFF
MARKING DETAIL A” (SEE TABLE)
FIG. 2 FIG. 3 FIG. 4 FIG. 5
FIG. 1 FIG. 6
OFF OFF
O
O
LINE
LOAD LINE LOAD LINE LOAD LINE
MARKING DETAIL “B” (SEE TABLE)
OFFON
ON OFFON
ON
O
O
LOAD
LINE
ROCKER HANDLE
COLOR
INDICATING COLOR
ON
I
INDICATION “ON”
Mounting/Indicator Code: J, K, L
OFF
O
Notes: A. Bezels of IALBX, IULBX, IELB, IELBX are black.
B. Consult factory for other marking options.
Black
Red
Grey
Orange
White
-00
-20
-40
-50
-90
-01
-21
-41
-51
-91
-02
-22
-42
-52
-92
-03
-23
-43
-53
-93
-04
-24
-44
-54
-94
-05
-25
-45
-55
-95
-06
-26
-46
-56
-96
I-O
Fig.2
Unmarked
Marking
Detail
Seventh Decision
7
Rocker Handle Color, Indicator Color and Marking Selection (See Notes)
LELZX & LMLZX Rocker Handle (Single Rocker Color)
Rocker
Handle
Color
Indicating
Color
Marking
Color Indicates:
On-Off
Fig.1
On-Off
I-O
Fig.3
On-Off
I-O
Fig.6
I-O
Fig.5
On-Off
Fig.4
A
Vertical Mounting Horizontal Mounting
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Black
Black
Black
White
Red
Green
White
White
White
On
On
On
-J0
-K0
-L0
-J1
-K1
-L1
-J2
-K2
-L2
-J3
-K3
-L3
-J4
-K4
-L4
-J5
-K5
-L5
-J6
-K6
-L6
B
C
White
White
Black
Black
Black
LELZX & LMLZX Rocker Handle (Dual Rocker Color)
Black
Black
Black
Black
Black
Black
White
Red
Green
White
Red
Green
White
White
White
White
White
White
On
On
On
Off
Off
Off
-A0
-B0
-C0
-F0
-G0
-H0
-A1
-B1
-C1
-F1
-G1
-H1
-A2
-B2
-C2
-F2
-G2
-H2
-A3
-B3
-C3
-F3
-G3
-H3
-A4
-B4
-C4
-F4
-G4
-H4
-A5
-B5
-C5
-F5
-G5
-H5
-A6
-B6
-C6
-F6
-G6
-H6
Black
Black
Black
Black
White
Red
Green
Yellow
White
Red
Green
Yellow
Off
Off
Off
Off
-M0
-N0
-P0
-R0
N/A
N/A
N/A
N/A
-M2
-N2
-P2
-R2
-M3
-N3
-P3
-R3
N/A
N/A
N/A
N/A
-M6
-N6
-P6
-R6
-M5
-N5
-P5
-R5
A
LELBX Rocker Handle (Dual Rocker Color)
INDICATION “OFF”
Mounting/Indicator Code: M, N, P, R
NO
ACTUATION
ACCESS
OPTIONAL
HANDLE
POSITION “OFF”
WITH GUARD
HANDLE
POSITION “ON”
WITH GUARD
MARKING DETAIL “C” (SEE TABLE)
FIG. 2 FIG. 3 FIG. 6
LINE
LOAD LOAD
LINE
O
OFF ON
O
O
ON
OFF
MARKING DETAIL “A” (SEE TABLE)
LOAD LOAD
LINE
LOAD LOAD
LINE LINELINE
FIG. 2 FIG. 3 FIG. 4 FIG. 5
FIG. 1 FIG. 6
OFFON
ON
OFF
OFFON
ON
OFF
OO
O
O
LINE LINE
ROCKER
HANDLE
COLOR
INDICATING
COLOR
INDICATING
COLOR
ROCKER
HANDLE
COLOR
INDICATION “ON”
Mounting/Indicator Code: A, B, C
INDICATION “OFF”
Mounting/Indicator Code: F, G, H
ON
I
ON
I
O
OFF
OFF
O
INDICATION “OFF”
Mounting/Indicator Code: M, N, P, R
MARKING DETAIL “C” (SEE TABLE)
FIG. 2 FIG. 3 FIG. 6
LINE
LOAD LOAD
LINE
O
OFF ON
O
O
ON
OFF
MARKING DETAIL “B” (SEE TABLE)
FIG. 2 FIG. 3 FIG. 4 FIG. 5
FIG. 1 FIG. 6
OFFON
ON
OFF
OFFON
ON
OFF
OO
O
O
LINE
LOAD
LOAD LINE LOAD LINE LOAD LINE
LINE
ROCKER
HANDLE
COLOR
INDICATING
COLOR
ON
I
INDICATION “ON”
Mounting/Indicator Code: J, K, L
OFF
O
LINE
http://airpax.sensata.com/ IAL/CEL/LEL Series - Operating Characteristics 150
LEL Series - Decision Tables
IAL Series
154
Second Decision
Single pole
Two pole
Three pole
1
11
111
2
Poles
Fifth Decision
5
Rated Current
Use three numbers in build (.050 or 1.50 or 100).
Required value between .050 amps minimum
and 125 amps maximum.
Fourth Decision
4
Frequency and Delay
DC short delay
DC long delay
DC motor start
DC 125% instant trip
For addition of inertial delay, add an “F” to any
delay numeral. Example: -51F
*Not available above 100 amps.
-51
-52
-53*
-59
The shaded areas denote VDE and CCC
(if applicable) approval options. This
approval requires the addition of a V at
the end of the part number. The V will be
added to any part number formed
entirely from shaded decisions. If
non-shaded areas are selected, the unit
will not be VDE or CCC Approved, but
other approvals still apply.
V = VDE and CCC Approved
The approval requires the addition of a
C at the end of the part number. The
unit will not be VDE Approved.
C = CCC Approved
12 3 4
CEL 1 - 1REC4 - 51 - 20.0 - A - 01 - V
576
Example:
Third Decision
3
* Only one auxiliary switch is normally supplied on two
and three pole units switch is located in the right hand
pole (viewed from terminal end). Note, aux switch
followed by “R” indicates reverse mount option
** Not available for 125 amp single pole
Internal Conguration
Select Type and Terminal
First Decision
1
Type Terminal
Standard screw terminal,
no designation required
Stud terminals
Clip terminals
Bullet terminals
K
C
B
Description
Sixth Decision
6
Optional
Notes:
1. One or more descriptions may be used as required.
2. When this decision is not used, decision 7 may be
substituted and U.S. thread will be supplied.
Seventh Decision
7
LEL Toggle Handle Color Selection
Black w/ white markings
Yellow w/ black markings
Red w/ white markings
Blue w/ white markings
Green w/ white markings
Orange w/ black markings
White w/ black markings
-01
-11
-21
-31
-41
-61
-91
See alternate 7th Decision for ZX and BX Rocker
Handles.
CEL One handle per unit, UL489A Listed
CELZX One handle per unit, rocker handle,
UL489A Listed
CELBX One handle per unit, at rocker handle,
UL489A Listed
CELH One handle per pole, UL489A Listed
CML Single pole only, one handle per unit
mid-trip construction, UL489A Listed
-1REC4 Series with auxiliary switch
.110 quick connect
-1RLS4 ** Series with auxiliary switch
.110 quick connect, mid-trip only
-1REC5 Series with auxiliary switch
.187 quick connect
-1RS4 ** Alarm switch, .110 quick connect
-1 Series
CMLZX Single pole only, one handle per unit,
rocker handle w/ RLS aux switch,
mid-trip construction, UL489A Listed
CMLBX Single pole only, one handle per unit,
at rocker handle w/ RLS aux switch,
mid-trip construction, UL489A Listed
CMLH One handle per pole
mid-trip construction, UL489A Listed
The approval requires the addition of a
T at the end of the part number. The
unit will only be TÜV EN60947-2
approved with a single pole,
125 amp rating conguration.
T = TÜV Approved
-A Metric thread mounting inserts and
terminals
-G Snap-in mounting plate adapter with
handle guard (ZX, BX and snap-in only)
-T 80VDC, 10000AIC, (required over 50A)
-V 125VDC
-1 Silver 5/16” (.312”) bullet
-2 Gold 5/16” (.312”) bullet
-K 1/4-20 Stud (M6 stud when metric option
-A selected) 50A requires -K, >50A do
not use -K
-B Barrier
-P Snap-in mounting plate adapter
CEL DECISION TABLES
http://airpax.sensata.com/
IAL/CEL/LEL Series - Operating Characteristics
149 CEL Series - Decision Tables http://airpax.sensata.com
155
LINE LINE
FIG. 2 FIG. 3 FIG. 4 FIG. 5
FIG. 1 FIG. 6
ROCKER HANDLE
COLOR
INDICATING COLOR
INDICATING
COLOR
ROCKER HANDLE
COLOR
INDICATION “ON”
Mounting/Indicator Code: A, B, C
LOAD LOAD
LINE
LOAD LOAD
LINE
INDICATION “OFF”
Mounting/Indicator Code: F, G, H
LINELINE
Area reserved for
amperage marking.
ON
I
ON
I
O
OFF
OFF
O
OFF ON
ON
OFF
O
OFF ON
OO
O
ON
OFF
MARKING DETAIL A” (SEE TABLE)
FIG. 2 FIG. 3 FIG. 4 FIG. 5
FIG. 1 FIG. 6
OFF OFF
O
O
LINE
LOAD LINE LOAD LINE LOAD LINE
MARKING DETAIL “B” (SEE TABLE)
OFFON
ON OFFON
ON
O
O
LOAD
LINE
ROCKER HANDLE
COLOR
INDICATING COLOR
ON
I
INDICATION “ON”
Mounting/Indicator Code: J, K, L
OFF
O
Notes: A. Bezels of IALBX, IULBX, IELB, IELBX are black.
B. Consult factory for other marking options.
Black
Red
Grey
Orange
White
-00
-20
-40
-50
-90
-01
-21
-41
-51
-91
-02
-22
-42
-52
-92
-03
-23
-43
-53
-93
-04
-24
-44
-54
-94
-05
-25
-45
-55
-95
-06
-26
-46
-56
-96
I-O
Fig.2
Unmarked
Marking
Detail
Seventh Decision
7
Rocker Handle Color, Indicator Color and Marking Selection (See Notes)
LELZX & LMLZX Rocker Handle (Single Rocker Color)
Rocker
Handle
Color
Indicating
Color
Marking
Color Indicates:
On-Off
Fig.1
On-Off
I-O
Fig.3
On-Off
I-O
Fig.6
I-O
Fig.5
On-Off
Fig.4
A
Vertical Mounting Horizontal Mounting
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Black
Black
Black
White
Red
Green
White
White
White
On
On
On
-J0
-K0
-L0
-J1
-K1
-L1
-J2
-K2
-L2
-J3
-K3
-L3
-J4
-K4
-L4
-J5
-K5
-L5
-J6
-K6
-L6
B
C
White
White
Black
Black
Black
LELZX & LMLZX Rocker Handle (Dual Rocker Color)
Black
Black
Black
Black
Black
Black
White
Red
Green
White
Red
Green
White
White
White
White
White
White
On
On
On
Off
Off
Off
-A0
-B0
-C0
-F0
-G0
-H0
-A1
-B1
-C1
-F1
-G1
-H1
-A2
-B2
-C2
-F2
-G2
-H2
-A3
-B3
-C3
-F3
-G3
-H3
-A4
-B4
-C4
-F4
-G4
-H4
-A5
-B5
-C5
-F5
-G5
-H5
-A6
-B6
-C6
-F6
-G6
-H6
Black
Black
Black
Black
White
Red
Green
Yellow
White
Red
Green
Yellow
Off
Off
Off
Off
-M0
-N0
-P0
-R0
N/A
N/A
N/A
N/A
-M2
-N2
-P2
-R2
-M3
-N3
-P3
-R3
N/A
N/A
N/A
N/A
-M6
-N6
-P6
-R6
-M5
-N5
-P5
-R5
A
LELBX Rocker Handle (Dual Rocker Color)
INDICATION “OFF”
Mounting/Indicator Code: M, N, P, R
NO
ACTUATION
ACCESS
OPTIONAL
HANDLE
POSITION “OFF”
WITH GUARD
HANDLE
POSITION “ON”
WITH GUARD
MARKING DETAIL “C” (SEE TABLE)
FIG. 2 FIG. 3 FIG. 6
LINE
LOAD LOAD
LINE
O
OFF ON
O
O
ON
OFF
MARKING DETAIL “A” (SEE TABLE)
LOAD LOAD
LINE
LOAD LOAD
LINE LINELINE
FIG. 2 FIG. 3 FIG. 4 FIG. 5
FIG. 1 FIG. 6
OFFON
ON
OFF
OFFON
ON
OFF
OO
O
O
LINE LINE
ROCKER
HANDLE
COLOR
INDICATING
COLOR
INDICATING
COLOR
ROCKER
HANDLE
COLOR
INDICATION “ON”
Mounting/Indicator Code: A, B, C
INDICATION “OFF”
Mounting/Indicator Code: F, G, H
ON
I
ON
I
O
OFF
OFF
O
INDICATION “OFF”
Mounting/Indicator Code: M, N, P, R
MARKING DETAIL “C” (SEE TABLE)
FIG. 2 FIG. 3 FIG. 6
LINE
LOAD LOAD
LINE
O
OFF ON
O
O
ON
OFF
MARKING DETAIL “B” (SEE TABLE)
FIG. 2 FIG. 3 FIG. 4 FIG. 5
FIG. 1 FIG. 6
OFFON
ON
OFF
OFFON
ON
OFF
OO
O
O
LINE
LOAD
LOAD LINE LOAD LINE LOAD LINE
LINE
ROCKER
HANDLE
COLOR
INDICATING
COLOR
ON
I
INDICATION “ON”
Mounting/Indicator Code: J, K, L
OFF
O
LINE
http://airpax.sensata.com/ IAL/CEL/LEL Series - Operating Characteristics 150
CEL Series - Decision Tables
IAL Series
156
LELHP DECISION TABLES
LELPK One handle per unit
LMLPK One handle per unit, mid-trip
LELHPK One handle per pole
LMLHPK One handle per pole, mid-trip
LELZXPK One ZX rocker handle per unit (integral mounting)
LMLZXPK One ZX rocker handle per unit, mid-trip (integral mounting)
LELBXPK One BX rocker handle per unit (integral mounting)
LMLBXPK One BX rocker handle per unit, mid-trip (integral mounting)
LELHPK 11 - 1REC4 - 51 - 125. - A - 01 - V
Select Type with Stud Terminals
First Decision
Poles
Second Decision
11 Two pole (up to 150 amps)
111 Three pole (160 to 200 amps)
Internal Conguration
Third Decision
Frequency and Delay
Fourth Decision
Rated Current (Amps)
Fifth Decision
-51 DC 125% short delay (125 to 150 amp) 125.
130.
135.
150.
175.
200.
DC 135% short delay (160 to 200 amp)
-52 DC 125% long delay (125 to 150 amp)
DC 135% long delay (160 to 200 amp)
-59 DC 125% instant trip (125 to 150 amp)
DC 135% instant trip (160 to 200 amp)
7
Toggle Handle Color
Seventh Decision
Additional ratings available.
See LEL alternative 7th decision for
ZX & BX rocker handles
1. One toggle handle per unit on 125A to 150A units (2-parallel pole)
2. 175A to 200A (3-parallel pole) requires handle in each pole, “H” selection
-1 Series
-1REC4 Series with auxiliary switch
.110 quick connect
-1REG4 Series, aux switch (gold contacts)
.110 quick connect
-1RLSG4 Series, alarm aux switch (gold
contacts), .110 quick connect,
mid-trip only
-1RLS4 Series with alarm aux switch
.110 quick connect, mid-trip only
-1RS4 Series with alarm aux switch
.110 quick connect
-1RS4 Series with alarm aux switch
.187 quick connect
-1RS5 Series with alarm aux switch
.187 quick connect, mid-trip
-1REC5 Series with aux switch
.187 quick connect
-1RLS5 Series with alarm aux switch
.187 quick connect, mid-trip only
Example:
1 2 3 4 5 6 7
Sixth Decision
6
Optional (leave entry blank if none apply)
Notes:
1. One or more descriptions may be used as required.
2. When this decision is not used, decision 7 may be substituted and U.S. thread will be supplied.
-A Metric thread mounting inserts and terminals
-G Snap-in mounting plate adapter with handle guard (ZX, BX & snap-in only)
-X Handle guard with no actuate off feature (BX only, no mid-trip)
-P Snap-in mounting plate adapter
-31 Blue w/ white markings
-41 Green w/ white markings
-61 Orange w/ black markings
-01 Black w/ white markings
-11 Yellow w/ black markings
-21 Red w/ white markings
-91 White w/ black markings
The shaded areas denote VDE approval
options. This approval requires the
addition of a V at the end of the part
number. The V will be added to any part
number formed entirely from shaded
decisions. If non-shaded areas are
selected, the unit will not be VDE
approved, but other approvals still apply.
V = VDE Approved
For addition of intertial delay, add an “F” to any
delay option. Example: - 59 becomes -59F
http://airpax.sensata.com/
IAL/CEL/LEL Series - Operating Characteristics
149 LELHP Series - Decision Tables http://airpax.sensata.com
157
CELHPK 11 - 1REC4 - 51 - 125. - A - 01 - V
Select Type
First Decision
CELP One toggle handle per unit
Poles
Second Decision
11 Two pole (up to 150 amps)
111 Three pole (160 to 250 amps)
1111 Four pole (400 amps)
Internal Conguration
Third Decision
Frequency and Delay
Fourth Decision
Rated Current (Amps)
Fifth Decision
-51 DC 125% short delay (101 to 150 amp) 125.
130.
135.
150.
175.
200.
400.
DC 135% short delay (160 to 250 amp)
-52 DC 125% long delay (101 to 150 amp)
DC 135% long delay (160 to 250 amp)
-53 DC 125% motor start (101 to 150 amp)
DC 135% motor start (160 to 250 amp)
-59 DC 125% instant trip (101 to 150 amp)
DC 135% instant trip (160 to 250 amp)
7
Toggle Handle Color
Seventh Decision
Additional ratings available. See LEL alternative 7th decision for
ZX & BX rocker handles
CELHP One toggle handle per pole
CMLHP One toggle handle per pole,
mid-trip construction
CELZXP One rocker handle per unit
CELBXP One at rocker handle per unit
1. One toggle handle per unit is available only on 101A to 200A (two parallel pole construction)
2. 201A to 250A (three parallel pole constructions) require handles in each pole, “H” version
rst decision
3. Unit supplied with bullet terminals will not have buss bar installed, unless requested, buss bar
supplied standard to 150A only.
4. One handle per unit is available for 100A to 200A (two parallel pole constructions) and
201A to 250A (three pole constructions) (ZX & BX versions only)
5. 400 amps available with toggle handes only
-0 Switch only
-1 Series
-1REC4 Series with auxiliary switch
.110 quick connect
-1RLS4 * Series with alarm aux. switch
.110 quick connect, mid-trip only
-1RS4 * Series with alarm aux. switch
.110 quick connect
-1RS4 * Series with alarm aux. switch
.187 quick connect
-1REC5 Series with auxiliary switch
.187 quick connect
-1RLS5 * Series with alarm aux. switch
.187 quick connect, mid-trip only
1. Only one auxiliary switch is normally supplied
on two and three pole units. Switch is located in
the right hand pole (viewed from terminal end
panel mount position).
2. When more than one aux. switch is required,
change the 1 (of the 1REC4) to 2 or 3. If switches
are mixed, then use “2R” or 3R”.
* Not available at 400 amps
Example:
Terminal
Standard screw terminal,
no designation required
Stud terminals
Clip terminals
Bullet terminals
K
C
B
1 2 3 4 5 6 7
Sixth Decision
6
Optional (leave entry blank if none apply)
Notes:
1. One or more descriptions may be used as required.
2. When this decision is not used, decision 7 may be substituted and U.S. thread will be supplied.
-A Metric thread mounting inserts and terminals
-G Snap-in mounting plate adapter with handle guard (ZX, BX & snap-in only)
-1 Silver 5/16” (.312”) bullet
-2 Gold 5/16” (.312”) bullet
-X Handle guard with no actuate off feature (BX only, no mid-trip)
-B Barrier
-01 Black w/ white markings
-11 Yellow w/ black markings
-21 Red w/ white markings
-31 Blue w/ white markings
-41 Green w/ white markings
-61 Orange w/ black markings
-91 White w/ black markings
The shaded areas denote VDE approval
options. This approval requires the
addition of a V at the end of the part
number. The V will be added to any part
number formed entirely from shaded
decisions. If non-shaded areas are
selected, the unit will not be VDE
approved, but other approvals still apply.
V = VDE Approved
CELHP DECISION TABLES
http://airpax.sensata.com/ IAL/CEL/LEL Series - Operating Characteristics 150
LELHP Series - Decision Tables
IAL Series
158
©2013 Sensata Technologies, Inc. All rights reserved worldwide. The following data sheet is an excerpt from our Airpax™ Power
Protection Catalog, Literature # 2455005000, printed in the USA, May 9th, 2013.
Important Notice: Sensata Technologies reserves the right to make changes to, or to discontinue, any product or service identified in
this publication without notice. Before placing orders, users should obtain the latest version of the relevant information to verify that
the information being relied upon is current.
Sensata Technologies assumes no responsibility for customers’ product designs or applications. Users must determine the suitability
of the Sensata device described in this publication for their application, including the level of reliability required. Many factors beyond
Sensata’s control can affect the use and performance of a Sensata product in a particular application, including the conditions under
which the product is used and the time and environmental conditions in which the product is expected to perform. As these factors
are uniquely within the user’s knowledge and control, it is essential that the user evaluate the Sensata product to determine whether it
is fit for a particular purpose and suitable for the user’s application.
Sensata Technologies products are sold subject to Sensata’s Terms and Conditions of Sale which can be found at:
www.sensata.com/terms.htm
http://airpax.sensata.com/
Sensata Technologies Inc.
529 Pleasant Street
Attleboro, MA 02703, USA
Phone: +1 508-236-3287