File Nr. 3900.18-450.113.15 | Revision: 201705
1
1
ZCM Series Datasheet
SMD Precision Metal Film Resistors | MELF Style
ELECTRICAL SPECIFICATIONS
Type
ZCM204
ZCM207
Historical Part Number SMD ZC0204
ZC0207
Nominal Power Rating P70 [W] 0,4 1,0
Resistance Range [Ω]
0R22 … 10M
0R16 … 10M
E-Series E24 / E96 / E192
Tolerances ±[%] B = 0,1% , C = 0,25% , D = 0,5% , F = 1% , G = 2% , J = 5%
Temperature Coefficient
IEC60115-1 clause 4.2 ; 4.8
(+20 / -55[°C] and (+20 / +125[°C])
±[10-6*K-1] Depends on the value, please check the table below
Working Temperature Range [ºC] -55 … +155
Permissible film temperature
(
ϑ
F max.)
[ºC] 155
Max. Working Voltage [AC or DC]RMS 200 350
Dielectric Withstanding Voltage
IEC115-1 clause 4.7 (1[min])
[V]RMS 300 500
DIMENSIONS [mm]
Type
Historical
P/N:
L Ø D L1 Ø D1 A MASS
(mg)
ZCM204
ZC0204
3,6
+0 /-0,2
1,4
+0 /-0,1
1,8
min.
D
+0 /-0,15
0,80
±0,10
22
ZCM207 ZC0207
5,8
+0 /-0,3
2,2
±0,2
2,6
min.
D
+0 /-0,2
1,25
±0,2
77
Recommended solder pads dimensions
Type
Wave soldering Reflow soldering
I a b c I a b c
ZCM204
1,5
1,5
1,8
4,5
1,7
1,2
1,6
4,1
ZCM207
2,4
2,3
2,6
7,0
2,6
2,0
24
6,6
FEATURES
Precision MELF resistor
Advanced MELF technology
Best in class pulse load capability
Biased (85/85) test (±0,25% R) up to 1M0
AEC – Q200 Qualified
Intrinsic sulfur resistance
RoHs & REACH Compliant
ORDERING CODE-Example
New SAP Part Nr.:
ZCM
207
F
K
E
07-
1K
AA
Serie
Power rating
Tol.
Pack-Code
TCR
Forming type
R Value
Special
204 = 0,4W
207 = 1,0W
B = ±0,1%
C = ±0,25%
D = ±0,5%
F = ±1%
G = ±2%
J
= ±5%
K = Blister
tape reel
C = ±15ppm
D = ±25ppm
E = ±50ppm
F = ±100ppm
07- = 07 inch
(Reel diameter)
or
13- = 13 inch
(Reel diameter)
AA = Standard
H
istorical VTM Part Nr.:
ZC
0207
F
K
E
07
1K
Type
Size
Tol.
K = Blister tape reel
TC
Reel diam.
R Value
APPLICATIONS
Automotive
Charger
Alternative
Energy
Power Supply
Home Appliances
Industrial
AEC - Q200
Qualified
ZCM Series Datasheet
File Nr. 3900.18-450.113.15 | Revision: 201705
1
2
PERFORMANCE DATE
Type ZCM204
ZCM207
Historical Part Number ZC0204 ZC0207
Climatic Category 55/155/56
Short Time Overload
IEC60115-1 clause 4.13
(U=2,5* or ≤2* Umax, 5 [s])
±[%] 0,03 (≤1M) ; 0,1 (>1M) 0,03 (≤1M) ; 0,15 (>1M)
Single pulse high voltage overload
IEC60115-1 clause 4.27
RPU **10
70
=
,
Severity 4, 10 pulses 10[µs]/700[µs]
±[%] 0,15 0,25
Periodic electric overload
IEC60115-1 clause 4.39
RPU **15
70
=
, 0.1[s] on, 2.5 [s] off, 1000 cycles
±[%] 0,15 0,15
Failure Rate
(Total, ϑ0 , max, 60[%] cont. lev.) [10-9 h-1] ≤ 0,1
Endurance at 70ºC, standard operation
IEC60115-1 clause 4.25.1
(P70, @ 70[°C], 1,5[h]ON ; 0,5[h]OFF)
±[%] 1000h 0.15 (<10R) ; 0.1 (10R≤1M) ; 0.25 (>1M) 0,15 (≤1M) ; 0,5 (>1M)
8000h 0.3 (<10R) ; 0.2 (10R≤1M) ; 0.5 (>1M) 0,3 (≤1M) ; 1 (>1M)
Damp Heat, Steady State
IEC60115-1 clause 4.24
(40[°C], 93[% r.h.], 56[d])
±[%] 0,15 (≤ 1M) ; 0,25 (>1M) 0,25 (≤ 1M) ; 1 (>1M)
Biased Humidity
IEC60068-2-67
)
**3
.0],
[%85
],[º
85
(
70
5
2
RPURH
C=
±
±
±[%] 0,25 (≤ 1M) ; 2 (>1M) 0,5 (≤ 1M) ; 2 (>1M)
Temperature Cycling
IEC60068-2-14 ; IEC60115-1 clause 4.19
(-55 ~ +125[°C], 30[min] each , 1000 cycles)
±[%] 0,15 (≤ 1M) ; 0,25 (>1M) 0,25
Vibration
IEC60068-2-6 ; IEC60115-1 clause 4.22
(10;2000[Hz], ≤1,5[mm] , or ≤200[m/s2] 7,5[h])
±[%] 0,05 (≤ 1M) ; 0,1 (>1M) 0,05
Resistance to Soldering Heat
IEC60115-1 clause 4.18
(260±5 [°C], 10±1[s])Solder bath method
±[%] 0,1 (≤ 1M) ; 0,05 (>1M) 0,1 (≤ 1M) ; 0,05 (>1M)
Electrostatic Discharge
IEC60115-1 clause 4.38 ; IEC61340-3-1
( 3 positives + 3 negatives discharges)
±[%] 0,5 [2 kV] 0,5 [4 kV]
Voltage proof
IEC60115-1 clause 4.7
URMS=UINS, 60 [s]
No flash over or breakdown
Flammability
IEC60115-1 clause 4.35, IEC60695-11-5
Needle flame test, 10[s]
No burning after 30[s]
Solderability
IEC60068-2-20 ; IEC60115-1 clause 4.17
(235±3[ºC] 2±0 ,2[s],SnAg3Cu0 .5)
≥ 95% covered, no visible damage
Component Resistance to Solvents
IEC60068-2-45 ; IEC60115-1 clause 4.29
(50[ºC] method 2)
No visible damage
Resistance to solvents of Marking
IEC60068-2-45 ; IEC60115-1 clause 4.30
(50[ºC] method 1)
Marking visible , no visible damage
Marking
IEC60062 Color code
NOTES: MARKING [COLOR CODE]:
•
ZCM204 Color code marking is applied according to IEC 60062 in four bands (E24 series) for 5 % tolerance, or in five bands (E96 or E192 series).
Each color band appears as a single solid
line, voids are permissible if at least 2/3 of the band is visible from each radial angle of view. The
last color band for tolerance is approximately 50 % wider than the other bands.
•
ZCM207 Color code marking is applied according to IEC 60062 in four (E24 series) or six bands (E96 series). Each color band appears as a single
solid line, voids are permissible if at least
2/3 of the band is visible from each radial angle of view. The last color band represents the TCR for
resistors with TCR ≤50 ppm/K and nominal tolerance ≤1 %. Zero ohm jumpers are
marked with one centered black band.
ZCM Series Datasheet
File Nr. 3900.18-450.113.15 | Revision: 201705
1
3
Notes :
• ZCM204 - The color of the body coating is light green for jumpers and for a temperature coefficient of ±50 ppm/K or ±100 ppm/K, pink for ±25 ppm/K,
or violet for ±15 ppm/K.
•
ZCM207 - TCR ±10 ppm/K and ±5 ppm/K in resistance range 100Ω to 100kΩ on request.
•
Zero ohm jumper - Are marked with one centered black band.
NOTES: RESISTOR BODY COLOR CODE:
• The body coating color is light green for jumpers and for a temperature coefficient of ±50 or 100 [ppm], pink for ±25[ppm] and violet for ±15[ppm]
MAXIMUM RESISTANCE CHANGE AT RATED DISSIPATION
ZCM204
ZCM207
OPERATION MODE
PRECISION
STANDARD
POWER
PRECISION
STANDARD
POWER
Rated Power dissipation P
70
[W]
0,07
0,25
0,4
0,125
0,4
1,0
Operating temp. range [ºC]
-10 to 85
-55 to 125
-55 to 155
-10 to 85
-55 to 125
-55 to 155
Permissible film temperature ϑF Max [ºC]
85
125
155
85
125
155
Resistance range
10R – 1M
R22 – 1M
R22 – 10M
100R – 511K
1R0 – 1M
1R0 – 1M
Max. Resistance drift [%]
[ΔR/R]
1000h
≤0,05
≤0,15
≤0,25
≤0,05
≤0,15
≤0,25
8000h
≤0,1
≤0,3
≤0,5
≤0,1
≤0,3
≤0,5
225 000h
≤0,25
≤0,75
-
≤0,25
≤1,0
-
PERFORMANCE GRAPH’s
TEMPERATURE COEFFICIENT
ZCM204
ZCM207
Resistance range
Tolerance
TCR
E-Series
0R22 … 0R91
0R16 … 0R91
± 5%
± 100 ppm/K E24
0R22 … 0R91
± 2%
0R82… 10M
1R… 10M
± 1%
± 50 ppm/K
E24 / E96
10R… 1M65
1R… 2M21
± 0,5%
E24 / E192
10R… 1M65
43R… 1M
± 0,5%
± 25 ppm/K E24 / E192
22R… 1M65
43R… 1M
± 0,25%
22R… 1M65
43R… 1M
± 0,1%
10R… 221K
100R… 511K
± 0,5%
± 15 ppm/K E24 / E192
22R… 221K
100R… 511K
± 0,25%
43R… 221K
100R… 511K
± 0,1%
Jumper I
max
= 3A
Jumper I
max
= 5A
≤ 10 mΩ
ZCM20 7
ZCM20 4
Resistance value [Ω]
ZCM20 4
ZCM20 7
ZCM20 4
ZCM20 7
ZCM20 7
ZCM20 4
ZCM Series Datasheet
File Nr. 3900.18-450.113.15 | Revision: 201705
1
4
PACKAGING - Blister tape
The type ZCM is packed in antistatic blister tape a ccording to IEC60286-3, type 2a, packing details described be low,
Type A0 B0 F W D1 T2
ZCM204 1,55±0,1 3,7±0,1 3,5±0,05 8,0.±0,3
1,0 ≤ 1,8
ZCM207
2,40
±0,1
6,0
±0,1
5,5
±0,05
12,0.
±0,
3
1,5
≤ 2,7
Type
W1
[±1,5]
W2
[max]
ZCM204 8,4 14,4
ZCM207 12,4 18,4
Type
Packaging
[dimensions]
Quantity
[pcs]
ZCM204 07(inch)
Blister tape
3000
ZCM207 1500
ZCM204 13(inch)
Blister tape
10000
ZCM207 7500
Resistance value [Ω]
ZCM204
ZCM20 7
ZCM20 4
ZCM20 7