DATA SHEET THIN-FILM CHIP RESISTORS TFx13 series, 0.1% TC25 10 TO 1 M Product Specification - Jul 10, 2003 V.3 sizes 1210, 1206, 0805, 0603 and 0402 Phycomp Product specification Thin-film chip resistors sizes 1210, 1206, 0805, 0603 and 0402 TFx13 series, 0.1% TC25 10 to 1 M FEATURES DESCRIPTION * High precision The resistors are constructed on a high grade ceramic body (aluminium oxide). Internal metal electrodes are added at each end and connected by a resistive paste which is applied to the top surface of the substrate. The composition of the paste is adjusted to give the approximate resistance required and the value is trimmed to within tolerance by laser cutting of this resistive layer. * High long-tem stability * Low temperature coefficient. APPLICATIONS * Converters * Printer equipment * Motherboards The resistive layer is covered with a protective coating and printed with the resistance value. Finally, the two external end terminations are added. To guarantee optimum solderability the outer layer consists of a lead-tin alloy. * Telecom * Consumer. QUICK REFERENCE DATA DESCRIPTION Size code Resistance range VALUE TF513 TF013 TF113 TF213 TF313 1210 1206 0805 0603 0402 10 to 1 M 10 to 1 M 10 to 1 M 10 to 332 k 10 to 100 k Resistance tolerance and series 0.1%; E24 and E96 series 25 x 10-6/K Temperature coefficient Maximum dissipation at Tamb = 70 C 0.25 W 0.125 W 0.125 W 0.1 W 0.0625 W Maximum permissible voltage (DC or RMS) 200 V 200 V 150 V 75 V 50 V Climatic category (IEC 60068) 55/125/56 Basic specification IEC 60115-8 and MIL-STD-202F 2003 Jul 10 Rev.3 2 www.yageo.com Phycomp Product specification Thin-film chip resistors sizes 1210, 1206, 0805, 0603 and 0402 TFx13 series, 0.1% TC25 10 to 1 M ORDERING INFORMATION Table 1 Ordering code indicating resistor type and packing TYPE SIZE CODE RESISTANCE VALUE TOL. (%) PAPER TAPE ON REEL 12NC ORDERING CODE TF513 1210 10 to 1 M 0.1 5000 2390 612 4xxxx TF013 1206 10 to 1 M 0.1 5000 2390 611 4xxxx TF113 0805 10 to 1 M 0.1 5000 2390 601 4xxxx TF213 0603 10 to 332 k 0.1 5000 2390 604 4xxxx TF313 0402 10 to 100 k 0.1 10000 2390 607 4xxxx Ordering code (12NC) * The resistors have a 12-digit ordering code starting with 2390; see Table 1. * The subsequent 4 digits indicate the resistor type and packing. * The remaining 4 digits indicate the resistance value: - The first 3 digits indicate the resistance value. Table 2 ORDERING EXAMPLE Last digit of 12NC RESISTANCE DECADE LAST DIGIT 1 to 97.6 9 100 to 976 1 1 k to 9.76 k 2 10 k to 97.6 k 3 100 k to 976 k 4 1 M 5 The ordering code of a TF013 resistor, value 1000 with 0.1% tolerance, supplied on paper tape of 5000 units per reel is: 2390 611 41002. - The last digit indicates the resistance decade in accordance with Table 2. 2003 Jul 10 Rev.3 3 www.yageo.com Phycomp Product specification Thin-film chip resistors sizes 1210, 1206, 0805, 0603 and 0402 TFx13 series, 0.1% TC25 10 to 1 M FUNCTIONAL DESCRIPTION DERATING Product characterization The rated power that the resistor can dissipate depends on the operating temperature; see Fig.1. Standard values of nominal resistance are taken from the E24 and E96 series for resistors with a tolerance of 0.1%. The values of the E24 and E96 series are in accordance with "IEC publication 60063". MLB206 Pmax (%Prated ) 100 Limiting values 50 TYPE LIMITING LIMITING VOLTAGE(1) POWER (W) (V) TF513 200 0.25 TF013 200 0.125 TF113 150 0.125 TF213 75 0.1 TF313 50 0.0625 0 55 Fig.1 0 50 70 100 125 o Tamb ( C) Maximum dissipation (Pmax) in percentage of rated power as a function of the ambient temperature (Tamb). Note 1. The maximum voltage that may be continuously applied to the resistor element, see "IEC publication 60115-8". 2003 Jul 10 Rev.3 4 www.yageo.com Phycomp Product specification Thin-film chip resistors sizes 1210, 1206, 0805, 0603 and 0402 TFx13 series, 0.1% TC25 10 to 1 M OUTLINES MECHANICAL DATA Mass per 100 units TYPE MASS (g) TF513 1.67 TF013 1 TF113 0.55 TF213 0.25 TF313 0.052 protective coat resistor layer inner electrode T end termination ceramic substrate Marking tb protective coat TYPE E24 E96 TF513 4 digits 4 digits TF013 4 digits 4 digits TF113 4 digits 4 digits TF213 3 digits 3 digits EIA-96 TF313 tt 1001 W no marking CCB633 L 4-DIGIT MARKING For values up to 97.6 the R is used as a decimal point. For values of 1 k or greater the first 3 digits apply to the resistance value and the fourth indicates the number of zeros to follow. Example MARKING For dimensions see Table 3. Fig.2 Table 3 RESISTANCE 10R0 10 10R2 10.2 1001 1 k 2003 Jul 10 Rev.3 marking Outlines. Chip resistor type and relevant physical dimensions; see Fig.2 L (mm) W (mm) T (mm) tt (mm) tb (mm) TF513 (1210) 3.1 0.1 2.6 0.1 0.55 0.1 0.50 0.2 0.5 0.2 TF013 (1206) 3.1 0.1 1.6 0.1 0.55 0.1 0.45 0.2 0.4 0.2 TF113 (0805) 2.0 0.1 1.25 0.1 0.50 0.1 0.35 0.2 0.35 0.2 TF213 (0603) 1.6 0.1 0.8 0.1 0.45 0.1 0.25 0.15 0.25 0.15 TF313 (0402) 1.0 0.1 0.50 0.05 0.30 0.05 0.20 0.1 0.25 0.1 TYPE 5 www.yageo.com Phycomp Product specification Thin-film chip resistors sizes 1210, 1206, 0805, 0603 and 0402 TFx13 series, 0.1% TC25 10 to 1 M 3-DIGIT MARKING 3-DIGIT EIA-96 MARKING MARKING OF PACKING MATERIAL The first 2 digits apply to the resistance value and the third indicates the number of zeros to follow. The first 2 digits apply to the resistance value and the third character indicates the multiplier as shown in Tables 4 and 5. Example Example The packing material is also marked and includes resistance value, tolerance, catalogue number, quantity, production period, batch number and source code. MARKING RESISTANCE MARKING RESISTANCE 120 12 10X 12.4 123 12 k 10C 12.4 k 124 120 k 10D 124 k Table 4 First two digits of the resistance code CODE VALUE CODE VALUE CODE VALUE CODE VALUE 01 100 25 178 49 316 73 562 02 102 26 182 50 324 74 576 03 105 27 187 51 332 75 590 04 107 28 191 52 340 76 604 05 110 29 196 53 348 77 619 06 113 30 200 54 357 78 634 07 115 31 205 55 365 79 649 08 118 32 210 56 374 80 665 09 121 33 215 57 383 81 681 10 124 34 221 58 392 82 698 11 127 35 226 59 402 83 715 12 130 36 232 60 412 84 732 13 133 37 237 61 422 85 750 14 137 38 243 62 432 86 768 15 140 39 249 63 442 87 787 16 143 40 255 63 453 88 806 17 147 41 261 65 464 89 825 18 150 42 267 66 475 90 845 19 154 43 274 67 487 91 866 20 158 44 280 68 499 92 887 21 162 45 287 69 511 93 909 22 165 46 294 70 523 94 931 23 169 47 301 71 536 95 953 24 174 48 309 72 549 96 976 Table 5 Multiplier codes CODE Y X Multiplier 10-2 10-1 2003 Jul 10 Rev.3 A 1 B C D E F 10 102 103 104 105 6 www.yageo.com Phycomp Product specification Thin-film chip resistors sizes 1210, 1206, 0805, 0603 and 0402 TEST AND REQUIREMENTS Essentially all tests are carried out in accordance with the schedule of "IEC publication 60115-8", category 55/125/56 (rated temperature range -55 to +125 C; damp heat, long term, 56 days). The testing also covers the requirements specified by EIA and MIL-STD-202F. TFx13 series, 0.1% TC25 10 to 1 M testing procedure for electronic components" and under standard atmospheric conditions in accordance with "IEC 60068-1", subclause 5.3. Unless otherwise specified the following values apply: Temperature: 15 C to 35 C Relative humidity: 25% to 75% The tests are carried out in accordance with IEC publication 60068, "Recommended basic climatic and mechanical robustness Table 6 Air pressure: 86 kPa to 106 kPa (860 mbar to 1060 mbar). In Table 6 the tests and requirements are listed with reference to the relevant clauses of "IEC publications 60115-8, 60068 and MIL-STD"; a short description of the test procedure is also given. In some instances deviations from the IEC recommendations were necessary for our method of specifying. All soldering tests are performed with mildly activated flux. Test procedures and requirements IEC 60115-8 CLAUSE IEC 60068-2 TEST METHOD MIL-STD TEST PROCEDURE REQUIREMENTS 4.4.1 visual examination no holes; clean surface; no damage 4.4.2 dimensions (outline) gauge see Table 3 4.5 resistance applied voltage (+0/-10%): R - Rnom: max. 0.1% 10 R < 100 : 0.3 V 100 R < 1 k: 1 V 1 k R < 10 k: 3 V 10 k R < 100 k: 10 V 100 k R < 1 M: 25 V 1 M: 50 V 4.18 202F method 210C resistance to soldering heat unmounted chips; 10 1 s; 260 5 C no visible damage 202F method 208G solderability unmounted chips completely immersed for 5 0.5 s in a solder bath at 230 5 C good tinning (95% covered); no damage 4.7 202F method 301 voltage proof on insulation maximum voltage (RMS) during 1 minute, metal block method no breakdown or flashover 4.13 MIL-R 55342D para. 4.7.5 short time overload room temperature; V = 2.5 x Vrated; 5 s (voltage not more than 2 x Vmax); specimen stabilized at room temperature for 30 minutes R/R max.: (0.5% + 0.05 ) 4.17 20 (Tb) 20 (Ta) 2003 Jul 10 Rev.3 7 R/R max.: (0.5% + 0.05 ) www.yageo.com Phycomp Product specification Thin-film chip resistors sizes 1210, 1206, 0805, 0603 and 0402 IEC 60115-8 CLAUSE IEC 60068-2 TEST METHOD MIL-STD 4.33 TEST bending TFx13 series, 0.1% TC25 10 to 1 M PROCEDURE REQUIREMENTS resistors mounted on a no visible damage 90 mm glass epoxy resin PCB R/R max.: (0.25% + 0.05 ) (FR4); bending: 2 mm for 1210 2 mm for 1206 3 mm for 0805 3 mm for 0603 2 mm for 0402 MIL-R 55342D para. 4.7.4 low temperature operation no visible damage -65 +0/-5 C for 1 hour; loaded with Vrated for R/R max.: (0.5% + 0.05 ) 45 +5/-0 minutes ON, and 15 +5/-0 minutes OFF; specimen stabilized at room temperature for 24 hours after test 202F method 107 thermal shock 2 minutes at LCT and 2 minutes at UCT; 5 cycles no visible damage 4.25.1 202F method 108A endurance 1000 +48/-0 hours; 70 2 C; loaded with Pn or Vmax; 1.5 hours on, 0.5 hours off; specimen stabilized at room temperature for 1 hour min. after test R/R max.: (0.5% + 0.05 ) 4.8.4.2 202F method 304 temperature coefficient at 25/LCT/25 C and 25/UCT/25 C 25 x 10-6/K 4.6.1.1 202F method 302 insulation resistance after 1 minute, metal block method 1210: 400 V (DC) 1206: 400 V (DC) 0805: 300 V (DC) 0603: 150 V (DC) 0402: 100 V (DC) Rins min.: 104 M leaching unmounted chips; 60 1 s; 260 5 C good tinning; no leaching moisture resistance 65 2 C; 95 +3/-5% RH; loaded with 0.01 Pn or Vmax for 42 damp heat cycles. (1 cycle consists of 7 steps; see Fig.3) R/R max.: (0.5% + 0.05 ) 4.19 14 (Na) EIA 575 3.13 EIA/IS 703 4.6 2003 Jul 10 Rev.3 202F method 106 8 R/R max.: (0.5% + 0.05 ) www.yageo.com Phycomp Product specification Thin-film chip resistors sizes 1210, 1206, 0805, 0603 and 0402 75 80 - 98% RH 90 - 98% RH temperature [C] TFx13 series, 0.1% TC25 10 to 1 M 90 - 98% RH 80 - 98% RH 90 - 98% RH initial drying 24 hours rate of change of temperature is unspecified, however, specimens shall not be subjected to radiant heating from chamber conditioning processes 50 end of final cycle; measurements as specified in 2.7 +10 C (+18 F) -2 C (-3.6 F) 25 initial measurements as specified in 2.2 0 temperature tolerance 2 C (3.6 F) unless otherwise specified voltage applied as specified in 2.4 STEP1 STEP2 prior to first cycle only HBK073 optional sub-cycle if specified (2.3); sub-cycle performed during any 5 of the first 9 cycles; humidity uncontrolled during sub-cycle circulation of conditioning air shall be at a minimum cubic rate per minute equivalent to 10 times the volume of the chamber STEP3 STEP4 STEP5 STEP6 STEP7 one cycle 24 hours; repeat as specified in 2.5 0 5 10 15 20 25 time [h] Fig.3 2003 Jul 10 Rev.3 Moisture resistance test requirements. 9 www.yageo.com Phycomp Product specification Thin-film chip resistors sizes 1210, 1206, 0805, 0603 and 0402 MOUNTING TFx13 series, 0.1% TC25 10 to 1 M Chip placement can be on ceramic substrates and printed-circuit boards (PCBs). Electrical connection to the circuit is by soldering. The finishing of the end terminations guarantees a reliable contact. Due to their rectangular shape and small dimensional tolerances, surface-mounted resistors are suitable for handling by automatic placement systems. Footprint dimensions D G E C B A F preferred direction during wave soldering solder land / solder paste pattern solder resist pattern occupied area tracks MBG628 E AVAILABLE AREA FOR TRACKS underneath the CHIP For dimensions see Table 7. Fig.4 Table 7 Recommended footprint dimensions. Reflow soldering; for dimensions see also Fig.4 FOOTPRINT DIMENSIONS (mm) A B C D E F G TFx313 0402 1.5 0.5 0.5 0.6 0.1 1.9 1.0 0.15 TFx213 0603 2.1 0.5 0.8 0.9 0.0 2.5 1.7 0.25 TFx113 0805 2.6 0.9 0.85 1.4 0.5 3.0 2.1 TFx013 1206 3.8 2.0 0.9 1.8 1.4 4.2 2.5 0.25 TFx513 1210 3.8 2.0 0.9 2.7 1.4 4.2 3.4 0.25 Table 8 IR soldering 0.25 Wave soldering; for dimensions see also Fig.4 G PROPOSED NUMBER AND DIMENSIONS OF DUMMY TRACKS (mm) PLACEMENT ACCURACY (mm) 3.2 1.9 1 x (0.15 x 0.8) 0.25 3.9 2.4 1 x (0.3 x 1.3) 0.25 1.25 3.9 2.4 3 x (0.25 x 1.7) 0.25 1.25 6.3 4.2 3 x (0.25 x 2.6) 0.25 FOOTPRINT DIMENSIONS (mm) SIZE CODE A B C D E F TFx213 0603 2.7 0.9 0.9 0.8 0.15 TFx113 0805 3.3 1.3 1.0 1.3 0.34 TFx013 1206 4.5 2.5 1.0 1.7 TFx513 1210 5.3 2.3 1.5 2.6 TYPE PROCESSING REMARKS PLACEMENT ACCURACY (mm) SIZE CODE TYPE 2003 Jul 10 Rev.3 10 www.yageo.com Phycomp Product specification Thin-film chip resistors sizes 1210, 1206, 0805, 0603 and 0402 SOLDERING CONDITIONS TFx13 series, 0.1% TC25 10 to 1 M Surface-mount resistors are tested for solderability at 235 C during 2 seconds. The test condition for no leaching is 260 C for 60 seconds. Typical examples of soldering processes that provide reliable joints without any damage, are given in Figs 5 and 6. The robust construction of chip resistors allows them to be completely immersed in a solder bath of 260 C for one minute. Therefore, it is possible to mount surfacemount resistors on one side of a PCB and other components on the reverse side (mixed PCBs). 300 MLA859 10 s T 260 C 245 C (C) 250 10 s 215 C 200 180 C 150 40 s 130 C 100 2 K/s 50 0 0 50 100 150 200 250 t (s) Typical values (solid line). Process limits (dotted lines). Fig.5 2003 Jul 10 Rev.3 Infrared soldering. 11 www.yageo.com Phycomp Product specification Thin-film chip resistors sizes 1210, 1206, 0805, 0603 and 0402 300 TFx13 series, 0.1% TC25 10 to 1 M 10 s T MLA861 (C) 235 C to 260 C 250 200 second wave 5 K/s first wave 2 K/s 200 K/s 150 100 C to 130 C forced cooling 100 2 K/s 50 0 0 50 100 150 200 t (s) 250 Typical values (solid line). Process limits (dotted lines). The resistors may be soldered twice in accordance with this method if desired. Fig.6 2003 Jul 10 Rev.3 Double wave soldering. 12 www.yageo.com Phycomp Product specification Thin-film chip resistors sizes 1210, 1206, 0805, 0603 and 0402 TFx13 series, 0.1% TC25 10 to 1 M PACKING Peel-off force Tape and reel specifications Peel-off forces of both paper and blister tapes are in accordance with "IEC 60286-3" that is, at a peel-off speed of 300 10 mm/minute, 0.1 N to 1.0 N for 8 mm tape. The peel-off angle should be between 165 and 180. All tape and reel specifications are in accordance with "IEC 60286-3". Basic dimensions are given in Figs 7, 8 and 9 and Tables 9, and 10. Paper tape specification P0 D0 T P2 E F cover tape W B0 MBG251 A0 P1 Cumulative tolerance over 10 holes: 0.2 mm. Bottom fixing tape thickness: 50 10 m. Top fixing tape thickness : 50 10 m. For dimensions see Table 9. Fig.7 Table 9 Paper tape. Dimensions of paper tape for relevant chip size; see Fig.7 TYPE AND SIZE CODE SYMBOL TF313 (0402) TF213 (0603) TF113 (0805) TF013 (1206) TF513 (1210) UNIT SIZE TOL. SIZE TOL. SIZE TOL. SIZE TOL. SIZE TOL. A0 0.65 0.1 1.10 0.1 1.65 0.1 1.90 0.1 2.80 0.1 mm B0 1.15 0.1 1.90 0.1 2.40 0.1 3.50 0.1 3.50 0.1 mm W 8.0 0.2 8.0 0.2 8.0 0.2 8.0 0.2 8.0 0.2 mm E 1.75 0.1 1.75 0.1 1.75 0.1 1.75 0.1 1.75 0.1 mm F 3.50 0.05 3.50 0.05 3.50 0.05 3.50 0.05 3.50 0.05 mm D0 1.5 +0.1/-0 1.5 +0.1/-0 1.50 +0.1/-0 1.5 +0.1/-0 1.5 +0.1/-0 mm P0 4.0 0.1 4.0 0.1 4.0 0.1 4.0 0.1 4.0 0.1 mm P1 2.0 0.05 4.0 0.05 4.0 0.05 4.0 0.05 4.0 0.05 mm P2 2.0 0.05 2.0 0.05 2.0 0.05 2.0 0.05 2.0 0.05 mm T 0.53 0.1 0.7 0.1 0.85 0.1 0.85 0.1 0.85 0.1 mm 2003 Jul 10 Rev.3 13 www.yageo.com Phycomp Product specification Thin-film chip resistors sizes 1210, 1206, 0805, 0603 and 0402 TFx13 series, 0.1% TC25 10 to 1 M Tape leader/trailer specification leader end empty compartments with cover tape (min. 240 mm) trailer end cover tape only leader 400 mm trailer (max. 260 mm) CCB325 Fig.8 Leader/trailer tape. Taping requirements Resistance side facing up. Component is free and not sticking to top and/or bottom tape. Component should be easy to remove from the carrier tape and the chip cavity should have no mechanical damage. 2003 Jul 10 Rev.3 14 www.yageo.com Phycomp Product specification Thin-film chip resistors sizes 1210, 1206, 0805, 0603 and 0402 TFx13 series, 0.1% TC25 10 to 1 M Reel specification W2 C N A HBK039 W1 Dimensions in mm. For reel dimensions see Table 10. Fig.9 Reel. Table 10 Reel dimensions; see Fig.9 SIZE CODE UNITS PER REEL TF313 0402 10000 TF213 0603 5000 TF113 0508 5000 TF013 1206 5000 TF513 1210 5000 TYPE 2003 Jul 10 Rev.3 TAPE WIDTH (mm) A (mm) N (mm) C (mm) W1 (mm) W2 MAX. (mm) 8 180 +0/-3 60 +1/-0 13.0 0.2 9.0 0.3 11.4 1 15 www.yageo.com Phycomp Product specification Thin-film chip resistors sizes 1210, 1206, 0805, 0603 and 0402 TFx13 series, 0.1% TC25 10 to 1 M REVISION HISTORY Revision Date Change Notification Description Rev.0 2001 Jul 09 - - First issue of this specification Rev.1 2001 Aug 02 - - Table 6: 4.33 bending requirements R/R max. changed from (0.5% + 0.05 ) into (0.25% + 0.05 ) Rev.2 2001 Sep 10 EBR-324001177 - range expanded with 0.25 W size 1210 resistors - MIL-STD test procedures added Rev.3 2003 Jul 10 - - Updated company logo - Marking code revised 2003 Jul 10 Rev.3 16 www.yageo.com Yageo print-friendly version Product Detail Information Product Group Resistor Chips Ordering Code RT0603BRD0710K Ordering Code 239060441003 Unified CTC RT0603BRD0710K Additional Product Code9T06031A1002BAHFT Description High Precision Thin Film 0603 10 kOhm +-0.1% Paper 178mm (7") 25 ppm/K Status Preferred Series Size Code Tolerance Packing Style TCR spec Reel size & Specialty Resistance Power Rating High Precison High Stability Chip Resistor 0603 (1608) +-0.1% Paper Tape +-25 ppm/C 180 mm (7") Reel 10 kOhm 1/16W Related Data Sheets, Catalogs and Application Notes: Datasheet - TFx13 series, 0.1% TC25, Rev.3 [164 kb] General data - Introduction, Rev.6 [397 kb] General data - Mounting, Rev.4 [240 kb] General data - Packing, Rev.5 [190 kb] General data - Marking [270 kb] Phycomp brand SMD Resistors selection tables 2005 [763 kb] Phycomp brand SMD Resistors + MLCC + HF Shortform 2005 [499 kb] Appl. note - High-stability thin-film chip resistors [444 kb] Product leaflet - Thin-film resistors [107 kb] General info - Standard Values in a Decade [8.39 kb] Appl. note - Low-ohmic & power chip resistors for power-control circuits [394 kb] Ordering information for customers in North America [8 kb] R-chip sample kits [62 kb] For optimal printing of Data sheets print from page 2 of the PDF. Note Clear Text Codes in the data sheets can differ from the Clear Text Codes displayed above. The CTC displayed above is a new code which has been introduced to align product codes in the complete file://///Garuda/AUTOMATION/AUTOMATION_CPR/...bitting/06172005/YAGO/9T06031A1002BAHFT.htm (1 of 2) [06-Jul-2005 9:44:59 AM] Yageo Yageo organisation. You can search products with the CTC displayed in the data sheet by using the competitor part number search function. Documents are in PDF format so to view and print them you will need Adobe Acrobat Reader installed on your computer. This is available free of charge. Copyright (c) 2002-2005 Yageo Corporation Privacy Policy | Access to and use of this web site is subject to the following Terms of use Springsite Technology file://///Garuda/AUTOMATION/AUTOMATION_CPR/...bitting/06172005/YAGO/9T06031A1002BAHFT.htm (2 of 2) [06-Jul-2005 9:44:59 AM] Yageo print-friendly version Product Detail Information Product Group Resistor Chips Ordering Code RT1206BRD07100K Ordering Code 239061141004 Unified CTC RT1206BRD07100K Additional Product Code9T12062A1003BAHFT High Precision Thin Film 1206 100 kOhm +-0.1% Paper 178mm (7") 25 Description ppm/K Status Preferred Series Size Code Tolerance Packing Style TCR spec Reel size & Specialty Resistance Power Rating High Precison High Stability Chip Resistor 1206 (3216) +-0.1% Paper Tape +-25 ppm/C 180 mm (7") Reel 100 kOhm 1/8W Related Data Sheets, Catalogs and Application Notes: Datasheet - TFx13 series, 0.1% TC25, Rev.3 [164 kb] General data - Introduction, Rev.6 [397 kb] General data - Mounting, Rev.4 [240 kb] General data - Packing, Rev.5 [190 kb] General data - Marking [270 kb] Phycomp brand SMD Resistors selection tables 2005 [763 kb] Phycomp brand SMD Resistors + MLCC + HF Shortform 2005 [499 kb] Appl. note - High-stability thin-film chip resistors [444 kb] Product leaflet - Thin-film resistors [107 kb] General info - Standard Values in a Decade [8.39 kb] Appl. note - Low-ohmic & power chip resistors for power-control circuits [394 kb] Ordering information for customers in North America [8 kb] R-chip sample kits [62 kb] For optimal printing of Data sheets print from page 2 of the PDF. Note Clear Text Codes in the data sheets can differ from the Clear Text Codes displayed above. The file://///Garuda/AUTOMATION/AUTOMATION_CPR/...bitting/06172005/YAGO/9T12062A1003BAHFT.htm (1 of 2) [06-Jul-2005 9:43:57 AM] Yageo CTC displayed above is a new code which has been introduced to align product codes in the complete Yageo organisation. You can search products with the CTC displayed in the data sheet by using the competitor part number search function. Documents are in PDF format so to view and print them you will need Adobe Acrobat Reader installed on your computer. This is available free of charge. Copyright (c) 2002-2005 Yageo Corporation Privacy Policy | Access to and use of this web site is subject to the following Terms of use Springsite Technology file://///Garuda/AUTOMATION/AUTOMATION_CPR/...bitting/06172005/YAGO/9T12062A1003BAHFT.htm (2 of 2) [06-Jul-2005 9:43:57 AM]