PIC18F26K22-I/ML - Microchip Technology

 2010 Microchip Technology Inc. DS80498B-page 1

PIC18(L)F25/45K22

The PIC18(L)F25/45K22 family devices that you have

received conform functionally to the current Device Data

Sheet (DS41412C), except for the anomalies described

in this document.

The silicon issues discussed in the following pages are

for silicon revisions with the Device and Revision IDs

listed in Table 1. The silicon issues are summarized in

Table 2.

The errata described in this document will be addressed

in future revisions of the PIC18(L)F25/45K22 silicon.

Data Sheet clarifications and corrections start on page 5,

following the discussion of silicon issues.

The silicon revision level can be identified using the

current version of MPLAB® IDE and Microchip’s

programmers, debuggers, and emulation tools, which

are available at the Microchip corporate web site

(www.microchip.com).

For example, to identify the silicon revision level using

MPLAB IDE in conjunction with MPLAB ICD 2 or

PICkit™ 3:

1. Using the appropriate interface, connect the

device to the MPLAB ICD 2 programmer/

debugger or PICkit™ 3.

2. From the main menu in MPLAB IDE, select

Configure>Select Device, and then select the

target part number in the dialog box.

3. Select the MPLAB hardware tool

(Debugger>Select Tool).

4. Perform a “Connect” operation to the device

(Debugger>Connect). Depending on the

development tool used, the part number and

Device Revision ID value appear in the Output

window.

The DEVREV values for the various PIC18(L)F25/

45K22 silicon revisions are shown in Tabl e 1 .

Note: This document summarizes all silicon

errata issues from all revisions of silicon,

previous as well as current. Only the

issues indicated in the last column of

Table 2 apply to the current silicon

revision (A4).

Note: If you are unable to extract the silicon

revision level, please contact your local

Microchip sales office for assistance.

TABLE 1: SILICON DEVREV VALUES

Part Number Device ID(1) Revision ID for Silicon Revision(2)

A2 A3 A4

PIC18F25K22 0101 0101 010x xxxx 0 0010 0 0011 0 0100

PIC18LF25K22 0101 0101 011x xxxx 0 0010 0 0011 0 0100

PIC18F45K22 0101 0101 000x xxxx 0 0010 0 0011 0 0100

PIC18LF45K22 0101 0101 001x xxxx 0 0010 0 0011 0 0100

Note 1: The Device ID is located in the last configuration memory space.

2: Refer to the “PIC18(L)F2XK22/4XK22 Flash Memory Programming Specification” (DS41398) for detailed

information on Device and Revision IDs for your specific device.

PIC18(L)F25/45K22 Rev. A2/A3/A4

Silicon Errata and Data Sheet Clarification

PIC18(L)F25/45K22

DS80498B-page 2  2010 Microchip Technology Inc.

TABLE 2: SILICON ISSUE SUMMARY

Module Feature Item

Number Issue Summary

Affected

Revisions(1)

A2 A3 A4

Voltage Reference Default Value 1.1 VREFCON0 = 0X00 at Reset. X X

Voltage Reference Internal Reference 1.2 Reference may be unstable at low

temperatures.

HLVD HLVD module 2. The HLVD module does not function. X X

Comparators CxSYNC Control 3. The comparator output to the device pin

(Cx) always bypasses the Timer1

synchronization latch.

HS Oscillator HS Oscillator Start-up 4. HS oscillator may not start at low voltage/

high temperature.

Clock Switching Fail-Safe mode 5.1 Execution is delayed when waking from

Sleep.

Clock Switching Fail-safe Clock Moni-

tor

5.2 When the FCMEN Configuration bit is set

and the IESO Configuration bit is not set,

then a clock failure during Sleep will not be

detected.

CTMU Current Source 6.1 Current source is noisy. X X

CTMU Control Register 6.2 Control registers are not cleared by

Resets.

CCP3, CCP4 and

CCP5

PWM mode 7. Clock selection by CCP2 only. X X

ADC GO/DONE bit 8. GO/DONE bit gets stuck. X X

Power-on Reset

(POR)

Power-on Reset 9.1 Transient current spikes on some parts

during power-up may cause the part to

become stuck in Reset.

XXX

Power-on Reset

(POR)

Power-on Reset 9.2 Min VDD for PIC18F2X/4XK22 parts is

limited to 2.3V.

Min VDD for PIC18LF2X/4XK22 parts is

1.8V.

XXX

Timer1/3/5 Gate Timer1/3/5 Gate 10. The Timer1/3/5 gate times cannot be

resolved to the two Least Significant bits,

when using FOSC as the Timer1/3/5

source.

XXX

Note 1: Only those issues indicated in the last column apply to the current silicon revision.

 2010 Microchip Technology Inc. DS80498B-page 3

PIC18(L)F25/45K22

Silicon Errata Issues

1. Module: Voltage Reference

1.1 The default value of VREFCON0 after Reset

is 0x00 instead of 0x10.

Work around

Select the desired fixed voltage reference buffer

as part of initialization.

Affected Silicon Revisions

1.2 Internal voltage reference may become

unstable at cold temperature.

Work around

None.

Affected Silicon Revisions

2. Module: HLVD

Although the HLVDIF flag will be set immediately

after enabling the HLVD circuit, the HLVD module

is not functional and should not be used.

Work around

None.

Affected Silicon Revisions

3. Module: Comparators

The CxSYNC controls are inoperative. The

comparator output (Cx) always bypasses the

Timer1 synchronization latch.

Work around

None.

Affected Silicon Revisions

4. Module: HS Oscillator

The HS oscillator may not start when VDD is less

than 3V, especially at high temperatures.

Work around

None.

Affected Silicon Revisions

5. Module: Clock Switching

5.1 When Clock Fail-Safe mode or Clock

Switchover mode is selected, then code

execution will be delayed after waking from

Sleep by the start-up time of the HFINTOSC.

Work around

Disable HFINTOSC stabilization time by setting

the HFOFST bit of the Configuration register 3H.

Affected Silicon Revisions

5.2 When the FCMEN Configuration bit is set

and the IESO Configuration bit is not set,

then a clock failure during Sleep will not be

detected.

Work around

The IESO Configuration bit must also be set when

the FCMEN Configuration bit is set.

Affected Silicon Revisions

Note: This document summarizes all silicon

errata issues from all revisions of silicon,

previous as well as current. Only the

issues indicated by the shaded column in

the following tables apply to the current

silicon revision (A4).

A2 A3 A4

PIC18(L)F25/45K22

DS80498B-page 4  2010 Microchip Technology Inc.

6. Module: CTMU

6.1 Current source may be noisy to the CTMU

module.

Work around

None.

Affected Silicon Revisions

6.2 CTMU control registers are not cleared by

the RESET instruction or MCLR Reset.

Work around

Clear the CTMU control registers as part of device

initialization.

Affected Silicon Revisions

7. Module: CCP3, CCP4 and CCP5

PWM mode does not work independently of

CCP2. Clock selection is cross-wired with that of

CCP2.

Work around

Use CCP1 and/or CCP2 for PWM applications.

Reserve CCP3, CCP4 and CCP5 for capture and

compare applications.

Affected Silicon Revisions

8. Module: ADC

GO/DONE bit may become stuck in GO mode.

Work around

Use the ADC FRC clock selection to reduce the

probability of the GO bit becoming stuck. To

capture the events when the GO bit does become

stuck, use one of the timers to determine if the GO

bit stays set longer than expected. When this

occurs, restart the ADC conversion by clearing the

GO/DONE bit and then setting the GO/DONE bit.

Affected Silicon Revisions

9. Module: Power-on Reset (POR)

9.1 There may be transient current spikes on

some parts during power-up. If the

application cannot supply enough current to

get past these transients, then the part may

become stuck in Reset.

Work around

Ensure that the application is capable of supplying

at least 30 mA of transient current during power-

up.

Affected Silicon Revisions

9.2 Min VDD for PIC18F2X/4XK22 parts is

limited to 2.3V. Min VDD for PIC18LF2X/

4XK22 parts is 1.8V.

Work around

None.

Affected Silicon Revisions

10. Module: Timer1/3/5 Gate

The Timer gate times cannot be resolved to the

two Least Significant timer bits when the source

frequency is FOSC (TMRxCS[1:0]=01). This is

because the gate edges are synchronized with the

FOSC/4 clock.

Work around

None.

Affected Silicon Revisions

A2 A3 A4

XXX

A2 A3 A4

XXX

A2 A3 A4

XXX

 2010 Microchip Technology Inc. DS80498B-page 5

PIC18(L)F25/45K22

Data Sheet Clarifications

The following typographic corrections and clarifications

are to be noted for the latest version of the device data

sheet (DS41412C):

1. Module: I/O Ports

In Table 10-5, the Buffer Type column listed ST

(Schmitt Trigger) for functions RB1-RB7, when

the Pin Type was I (Input), should be TTL. The

Table below reflects the correction.

Note: Corrections are shown in bold. Where

possible, the original bold text formatting

has been removed for clarity.

TABLE 10-5: PORTB I/O SUMMARY

Pin Function TRIS

Setting

ANSEL

Setting

Type

Buffer

Type Description

RB0/INT0/CCP4/

FLT0/SRI/SS2/

AN12

RB0 01O DIG LATB<0> data output; not affected by analog input.

10 I TTL PORTB<0> data input; disabled when analog input

enabled.

INT0 1 0 I ST External interrupt 0.

CCP4(3) 01O DIG Compare 4 output/PWM 4 output.

10 I ST Capture 4 input.

FLT0 10 I ST PWM Fault input for ECCP auto-shutdown.

SRI 10 I ST SR Latch input.

SS2(3) 10 I TTL SPI slave select input (MSSP2).

AN12 11 I AN Analog input 12.

RB1/INT1/P1C/

SCK2/SCL2/

C12IN3-/AN10

RB1 01O DIG LATB<1> data output; not affected by analog input.

10 ITTL PORTB<1> data input; disabled when analog input

enabled.

INT1 10 I ST External Interrupt 1.

P1C(3) 01O DIG Enhanced CCP1 PWM output 3.

SCK2(3) 01O DIG MSSP2 SPI Clock output.

10 I ST MSSP2 SPI Clock input.

SCL2(3) 01ODIGMSSP2 I

2CTM Clock output.

10 II

2C MSSP2 I2CTM Clock input.

C12IN3- 11 I AN Comparators C1 and C2 inverting input.

AN10 11 I AN Analog input 10.

Legend: AN = Analog input or output; TTL = TTL compatible input; HV = High Voltage; OD = Open Drain; XTAL = Crystal; CMOS =

CMOS compatible input or output; ST = Schmitt Trigger input with CMOS levels; I2CTM = Schmitt Trigger input with I2C.

Note 1: Default pin assignment for P2B, T3CKI, CCP3 and CCP2 when Configuration bits PB2MX, T3CMX, CCP3MX and

CCP2MX are set.

2: Alternate pin assignment for P2B, T3CKI, CCP3 and CCP2 when Configuration bits PB2MX, T3CMX, CCP3MX and

CCP2MX are clear.

3: Function on PORTD and PORTE for PIC18(L)F4XK22 devices.

PIC18(L)F25/45K22

DS80498B-page 6  2010 Microchip Technology Inc.

RB2/INT2/CTED1/

P1B/SDI2/SDA2/

AN8

RB2 01O DIG LATB<2> data output; not affected by analog input.

10 ITTL PORTB<2> data input; disabled when analog input

enabled.

INT2 10 I ST External interrupt 2.

CTED1 10 I ST CTMU Edge 1 input.

P1B(3) 01O DIG Enhanced CCP1 PWM output 2.

SDI2(3) 10 I ST MSSP2 SPI data input.

SDA2(3) 00ODIGMSSP2 I

2CTM data output.

10 II

2C MSSP2 I2CTM data input.

AN8 11 I AN Analog input 8.

RB3/CTED2/P2A/

CCP2/SDO2/

C12IN2-/AN9

RB3 01O DIG LATB<3> data output; not affected by analog input.

10 ITTL PORTB<3> data input; disabled when analog input

enabled.

CTED2 10 IST CTMU Edge 2 input.

P2A 01O DIG Enhanced CCP1 PWM output 1.

CCP2(2) 01O DIG Compare 2 output/PWM 2 output.

10 I ST Capture 2 input.

SDO2(2) 01O DIG MSSP2 SPI data output.

C12IN2- 11 I AN Comparators C1 and C2 inverting input.

AN9 11 I AN Analog input 9.

RB4/IOC0/P1D/

T5G/AN11

RB4 01O DIG LATB<4> data output; not affected by analog input.

10 ITTL PORTB<4> data input; disabled when analog input

enabled.

IOC0 10 I TTL Interrupt-on-change pin.

P1D 01O DIG Enhanced CCP1 PWM output 4.

T5G 10 I ST Timer5 external clock gate input.

AN11 11 I AN Analog input 11.

RB5/IOC1/P2B/

P3A/CCP3/T3CKI/

T1G/AN13

RB5 01O DIG LATB<5> data output; not affected by analog input.

10 ITTL PORTB<5> data input; disabled when analog input

enabled.

IOC1 10 I TTL Interrupt-on-change pin 1.

P2B(1)(3) 01O DIG Enhanced CCP2 PWM output 2.

P3A(1) 01O DIG Enhanced CCP3 PWM output 1.

CCP3(1) 01O DIG Compare 3 output/PWM 3 output.

10 I ST Capture 3 input.

T3CKI(2) 10 I ST Timer3 clock input.

T1G 10 I ST Timer1 external clock gate input.

AN13 11 I AN Analog input 13.

TABLE 10-5: PORTB I/O SUMMARY

Pin Function TRIS

Setting

ANSEL

Setting

Type

Buffer

Type Description

Legend: AN = Analog input or output; TTL = TTL compatible input; HV = High Voltage; OD = Open Drain; XTAL = Crystal; CMOS =

CMOS compatible input or output; ST = Schmitt Trigger input with CMOS levels; I2CTM = Schmitt Trigger input with I2C.

Note 1: Default pin assignment for P2B, T3CKI, CCP3 and CCP2 when Configuration bits PB2MX, T3CMX, CCP3MX and

CCP2MX are set.

2: Alternate pin assignment for P2B, T3CKI, CCP3 and CCP2 when Configuration bits PB2MX, T3CMX, CCP3MX and

CCP2MX are clear.

3: Function on PORTD and PORTE for PIC18(L)F4XK22 devices.

 2010 Microchip Technology Inc. DS80498B-page 7

PIC18(L)F25/45K22

RB6/KBI2/PGC RB6 01O DIG LATB<6> data output; not affected by analog input.

10 ITTL PORTB<6> data input; disabled when analog input

enabled.

IOC2 10 I TTL Interrupt-on-change pin.

TX2(3) 01O DIG EUSART 2 asynchronous transmit data output.

CK2(3) 01O DIG EUSART 2 synchronous serial clock output.

10 I ST EUSART 2 synchronous serial clock input.

PGC xx I ST In-Circuit Debugger and ICSPTM programming clock input.

RB7/KBI3/PGD RB7 01O DIG LATB<7> data output; not affected by analog input.

10 ITTL PORTB<7> data input; disabled when analog input

enabled.

IOC3 10 I TTL Interrupt-on-change pin.

RX2(2), (3) 10 I ST EUSART 2 asynchronous receive data input.

DT2(2), (3) 01O DIG EUSART 2 synchronous serial data output.

10 I ST EUSART 2 synchronous serial data input.

PGD xxO DIG In-Circuit Debugger and ICSPTM programming data output.

xx I ST In-Circuit Debugger and ICSPTM programming data input.

TABLE 10-5: PORTB I/O SUMMARY

Pin Function TRIS

Setting

ANSEL

Setting

Type

Buffer

Type Description

Legend: AN = Analog input or output; TTL = TTL compatible input; HV = High Voltage; OD = Open Drain; XTAL = Crystal; CMOS =

CMOS compatible input or output; ST = Schmitt Trigger input with CMOS levels; I2CTM = Schmitt Trigger input with I2C.

Note 1: Default pin assignment for P2B, T3CKI, CCP3 and CCP2 when Configuration bits PB2MX, T3CMX, CCP3MX and

CCP2MX are set.

2: Alternate pin assignment for P2B, T3CKI, CCP3 and CCP2 when Configuration bits PB2MX, T3CMX, CCP3MX and

CCP2MX are clear.

3: Function on PORTD and PORTE for PIC18(L)F4XK22 devices.

PIC18(L)F25/45K22

DS80498B-page 8  2010 Microchip Technology Inc.

APPENDIX A: DOCUMENT

REVISION HISTORY

Rev A Document (5/2010)

Initial release of this document.

Rev B Document (8/2010)

Updated errata to the new format; Updated for Revision

A4 silicon release; Added Modules 5.2, 9.1, 9.2 and 10.

Data Sheet Clarifications: Added Module 1.

 2010 Microchip Technology Inc. DS80498B-page 9

Information contained in this publication regarding device

applications and the like is provided only for your convenience

and may be superseded by updates. It is your responsibility to

ensure that your application meets with your specifications.

MICROCHIP MAKES NO REPRESENTATIONS OR

WARRANTIES OF ANY KIND WHETHER EXPRESS OR

IMPLIED, WRITTEN OR ORAL, STATUTORY OR

OTHERWISE, RELATED TO THE INFORMATION,

INCLUDING BUT NOT LIMITED TO ITS CONDITION,

QUALITY, PERFORMANCE, MERCHANTABILITY OR

FITNESS FOR PURPOSE. Microchip disclaims all liability

arising from this information and its use. Use of Microchip

devices in life support and/or safety applications is entirely at

the buyer’s risk, and the buyer agrees to defend, indemnify and

hold harmless Microchip from any and all damages, claims,

suits, or expenses resulting from such use. No licenses are

conveyed, implicitly or otherwise, under any Microchip

intellectual property rights.

Trademarks

The Microchip name and logo, the Microchip logo, dsPIC,

KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART,

PIC32 logo, rfPIC and UNI/O are registered trademarks of

Microchip Technology Incorporated in the U.S.A. and other

countries.

FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor,

MXDEV, MXLAB, SEEVAL and The Embedded Control

Solutions Company are registered trademarks of Microchip

Technology Incorporated in the U.S.A.

Analog-for-the-Digital Age, Application Maestro, CodeGuard,

dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN,

ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial

Programming, ICSP, Mindi, MiWi, MPASM, MPLAB Certified

logo, MPLIB, MPLINK, mTouch, Octopus, Omniscient Code

Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit,

PICtail, REAL ICE, rfLAB, Select Mode, Total Endurance,

TSHARC, UniWinDriver, WiperLock and ZENA are

trademarks of Microchip Technology Incorporated in the

U.S.A. and other countries.

SQTP is a service mark of Microchip Technology Incorporated

in the U.S.A.

All other trademarks mentioned herein are property of their

respective companies.

Printed on recycled paper.

ISBN: 978-1-60932-457-5

Note the following details of the code protection feature on Microchip devices:

• Microchip products meet the specification contained in their particular Microchip Data Sheet.

• Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the

intended manner and under normal conditions.

• There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our

knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data

Sheets. Most likely, the person doing so is engaged in theft of intellectual property.

• Microchip is willing to work with the customer who is concerned about the integrity of their code.

• Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not

mean that we are guaranteeing the product as “unbreakable.”

Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our

products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts

allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.

Microchip received ISO/TS-16949:2002 certification for its worldwide

headquarters, design and wafer fabrication facilities in Chandler and

Tempe, Arizona; Gresham, Oregon and design centers in California

and India. The Company’s quality system processes and procedures

are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping

devices, Serial EEPROMs, microperipherals, nonvolatile memory and

analog products. In addition, Microchip’s quality system for the design

and manufacture of development systems is ISO 9001:2000 certified.

DS80498B-page 10  2010 Microchip Technology Inc.

AMERICAS

Corporate Office

2355 West Chandler Blvd.

Chandler, AZ 85224-6199

Tel: 480-792-7200

Fax: 480-792-7277

Technical Support:

http://support.microchip.com

Web Address:

www.microchip.com

Atlanta

Duluth, GA

Tel: 678-957-9614

Fax: 678-957-1455

Boston

Westborough, MA

Tel: 774-760-0087

Fax: 774-760-0088

Chicago

Itasca, IL

Tel: 630-285-0071

Fax: 630-285-0075

Cleveland

Independence, OH

Tel: 216-447-0464

Fax: 216-447-0643

Dallas

Addison, TX

Tel: 972-818-7423

Fax: 972-818-2924

Detroit

Farmington Hills, MI

Tel: 248-538-2250

Fax: 248-538-2260

Kokomo

Kokomo, IN

Tel: 765-864-8360

Fax: 765-864-8387

Los Angeles

Mission Viejo, CA

Tel: 949-462-9523

Fax: 949-462-9608

Santa Clara

Santa Clara, CA

Tel: 408-961-6444

Fax: 408-961-6445

Toronto

Mississauga, Ontario,

Canada

Tel: 905-673-0699

Fax: 905-673-6509

ASIA/PACIFIC

Asia Pacific Office

Suites 3707-14, 37th Floor

Tower 6, The Gateway

Harbour City, Kowloon

Hong Kong

Tel: 852-2401-1200

Fax: 852-2401-3431

Australia - Sydney

Tel: 61-2-9868-6733

Fax: 61-2-9868-6755

China - Beijing

Tel: 86-10-8528-2100

Fax: 86-10-8528-2104

China - Chengdu

Tel: 86-28-8665-5511

Fax: 86-28-8665-7889

China - Chongqing

Tel: 86-23-8980-9588

Fax: 86-23-8980-9500

China - Hong Kong SAR

Tel: 852-2401-1200

Fax: 852-2401-3431

China - Nanjing

Tel: 86-25-8473-2460

Fax: 86-25-8473-2470

China - Qingdao

Tel: 86-532-8502-7355

Fax: 86-532-8502-7205

China - Shanghai

Tel: 86-21-5407-5533

Fax: 86-21-5407-5066

China - Shenyang

Tel: 86-24-2334-2829

Fax: 86-24-2334-2393

China - Shenzhen

Tel: 86-755-8203-2660

Fax: 86-755-8203-1760

China - Wuhan

Tel: 86-27-5980-5300

Fax: 86-27-5980-5118

China - Xian

Tel: 86-29-8833-7252

Fax: 86-29-8833-7256

China - Xiamen

Tel: 86-592-2388138

Fax: 86-592-2388130

China - Zhuhai

Tel: 86-756-3210040

Fax: 86-756-3210049

ASIA/PACIFIC

India - Bangalore

Tel: 91-80-3090-4444

Fax: 91-80-3090-4123

India - New Delhi

Tel: 91-11-4160-8631

Fax: 91-11-4160-8632

India - Pune

Tel: 91-20-2566-1512

Fax: 91-20-2566-1513

Japan - Yokohama

Tel: 81-45-471- 6166

Fax: 81-45-471-6122

Korea - Daegu

Tel: 82-53-744-4301

Fax: 82-53-744-4302

Korea - Seoul

Tel: 82-2-554-7200

Fax: 82-2-558-5932 or

82-2-558-5934

Malaysia - Kuala Lumpur

Tel: 60-3-6201-9857

Fax: 60-3-6201-9859

Malaysia - Penang

Tel: 60-4-227-8870

Fax: 60-4-227-4068

Philippines - Manila

Tel: 63-2-634-9065

Fax: 63-2-634-9069

Singapore

Tel: 65-6334-8870

Fax: 65-6334-8850

Taiwan - Hsin Chu

Tel: 886-3-6578-300

Fax: 886-3-6578-370

Taiwan - Kaohsiung

Tel: 886-7-213-7830

Fax: 886-7-330-9305

Taiwan - Taipei

Tel: 886-2-2500-6610

Fax: 886-2-2508-0102

Thailand - Bangkok

Tel: 66-2-694-1351

Fax: 66-2-694-1350

EUROPE

Austria - Wels

Tel: 43-7242-2244-39

Fax: 43-7242-2244-393

Denmark - Copenhagen

Tel: 45-4450-2828

Fax: 45-4485-2829

France - Paris

Tel: 33-1-69-53-63-20

Fax: 33-1-69-30-90-79

Germany - Munich

Tel: 49-89-627-144-0

Fax: 49-89-627-144-44

Italy - Milan

Tel: 39-0331-742611

Fax: 39-0331-466781

Netherlands - Drunen

Tel: 31-416-690399

Fax: 31-416-690340

Spain - Madrid

Tel: 34-91-708-08-90

Fax: 34-91-708-08-91

UK - Wokingham

Tel: 44-118-921-5869

Fax: 44-118-921-5820

Worldwide Sales and Service

08/04/10