Film Capacitors
EMI Suppression Capacitors (MKP)
Series/Type: B32921 ... B32926
Date: May 2005
© EPCOS AG 2006. Reproduction, publication and dissemination of this data sheet, enclosures hereto and the
information contained therein without EPCOS' prior express consent is prohibited.
Purchase orders are subject to the General Conditions for the Supply of Products and Services of the Electrical
and Electronics Industry recommended by the ZVEI (German Electrical and Electronic Manufacturers' Associ-
ation), unless otherwise agreed.
Please read "Important notes" on page 9.
Typical applications
X2 class for interference suppression
"Across the line" applications
Climatic
Max. operating temperature: 125 °C
Climatic category (IEC 60068-1): 40/105/56
Construction
Dielectric: polypropylene (MKP)
Plastic case (UL 94 V-0)
Epoxy resin sealing (UL 94 V-0)
Features
Very small dimensions
Self-healing properties
Terminals
Parallel wire leads, lead-free tinned
Standard lead lengths: 6 1 mm
Special lead lengths available on request
Marking
Manufacturer's logo, lot number,
date code, rated capacitance (coded),
cap. tolerance (code letter),
rated AC voltage,
series number, sub-class (X2),
dielectric code (MKP), climatic category,
passive flammability category, approvals.
Delivery mode
Bulk (untaped)
Taped (Ammo pack or reel)
For taping details, refer to chapter
"Taping and packing".
Dimensional drawing
Dimensions in mm
Lead spacing
±0.4
Lead diameter
d1
Type
10 0.6 B32921
15 0.8 B32922
22.5 0.8 B32923
27.5 0.8 B32924
37.5 1.0 B32926
Marking examples
= 10 mm ≥15 mm/CR≤1µF
= 22.5, 27.5,
37.5 mm/CR>1 µF
Approvals
Marks of conformity Standards Certificate
EN 132400, IEC 60384-14 40005536/40010694
UL 1414 / UL 1283 E97863 / E157153
CSA C22.2 No.1 / No. 8 E97863 / E157153 (approved by UL)
CQC (GB/T 14472-1998) CQC001007-14859
EMI suppression capacitors (MKP) B32921 ... B32926
X2 / 305 VAC
2
Overview of available types
Lead spacing 10 mm 15 mm 22.5 mm 27.5 mm 37.5 mm
Type B32921 B32922 B32923 B32924 B32926
CR(µF)
0.010
0.022
0.033
0.047
0.068
0.10
0.15
0.22
0.33
0.47
0.56
0.68
0.82
1.0
1.5
2.2
3.3
4.7
5.6
6.8
8.2
10
B32921 ... B32926
X2 / 305 VAC
3
Ordering codes and packing units
Lead spacing
mm
CR
µF
Max. dimensions
w×h×l
mm
Ordering code
(composition see
below)
Ammo
pack
pcs./unit
Reel
pcs./unit
Untaped
pcs./unit
Composition of ordering code
+ = Capacitance tolerance code: *** = Packaging code:
M = ±20%
K = ±10%
289 = Ammo pack
189 = Reel
000 = Untaped (lead length 6 1 mm)
(Closer tolerances on request) Preferred types
10 0.010 4.0 ×9.0 ×13.0 B32921C3103+*** 1000 1700 1000
0.022 4.0 ×9.0 ×13.0 B32921C3223+*** 1000 1700 1000
0.033 4.0 ×9.0 ×13.0 B32921C3333+*** 1000 1700 1000
0.047 5.0 ×11.0 ×13.0 B32921C3473+*** 830 1300 1000
0.047 6.0 ×12.0 ×13.0 B32921A2473+*** 680 1100 1000
0.068 6.0 ×12.0 ×13.0 B32921A2683M*** 680 1100 1000
0.068 6.0 ×12.0 ×13.0 B32921C3683+*** 680 1100 1000
0.10 6.0 ×12.0 ×13.0 B32921A2104M*** 680 1100 1000
0.10 6.0 ×12.0 ×13.0 B32921C3104M*** 680 1100 1000
15 0.033 5.0 ×10.5 ×18.0 B32922C3333+*** 1170 1300 1000
0.047 5.0 ×10.5 ×18.0 B32922C3473+*** 1170 1300 1000
0.068 6.0 ×11.0 ×18.0 B32922A2683+*** 960 1100 1000
0.068 5.0 ×10.5 ×18.0 B32922C3683+*** 1170 1300 1000
0.10 6.0 ×11.0 ×18.0 B32922A2104+*** 960 1100 1000
0.10 5.0 ×10.5 ×18.0 B32922C3104+*** 1170 1300 1000
0.15 7.0 ×12.5 ×18.0 B32922A2154+*** 830 900 1000
0.15 6.0 ×12.0 ×18.0 B32922C3154+*** 960 1100 1000
0.22 8.5 ×14.5 ×18.0 B32922A2224+*** 680 700 500
0.22 8.0 ×14.0 ×18.0 B32922T2224+*** 730 750 500
0.22 7.0 ×12.5 ×18.0 B32922C3224+*** 830 900 1000
0.22 8.0 ×14.0 ×18.0 B32922T3224+*** 730 750 500
0.33 9.0 ×17.5 ×18.0 B32922A2334+*** 640 700 500
0.33 13.0 ×14.0 ×18.0 B32922T2334+*** 500 300
0.33 8.0 ×14.0 ×18.0 B32922C3334M*** 730 750 500
0.33 8.5 ×14.5 ×18.0 B32922D3334+*** 680 700 500
0.33 13.0 ×14.0 ×18.0 B32922T3334+*** 500 300
0.47 9.0 ×17.5 ×18.0 B32922C3474+*** 640 700 500
0.56 11.0 ×18.5 ×18.0 B32922C3564+*** 550 250
0.68 11.0 ×18.5 ×18.0 B32922C3684M*** 550 250
B32921 ... B32926
X2 / 305 VAC
4
Ordering codes and packing units
Lead spacing
mm
CR
µF
Max. dimensions
w×h×l
mm
Ordering code
(composition see
below)
Ammo
pack
pcs./unit
Reel
pcs./unit
Untaped
pcs./unit
Composition of ordering code
+ = Capacitance tolerance code: *** = Packaging code:
M = ±20%
K = ±10%
289 = Ammo pack
189 = Reel
000 = Untaped (lead length 6 1 mm)
(Closer tolerances on request) Preferred types
22.5 0.33 8.5 ×16.5 ×26.5 B32923A2334+*** 480 500 510
0.33 6.0 ×15.0 ×26.5 B32923C3334M*** 680 700 720
0.33 7.0 ×16.0 ×26.5 B32923D3334+*** 580 600 630
0.33 7.5 ×14.0 ×26.5 B32923T3334+*** 550 500 570
0.47 8.5 ×16.5 ×26.5 B32923A2474M*** 480 500 510
0.47 10.5 ×16.5 ×26.5 B32923B2474+*** 390 400 540
0.47 8.5 ×16.5 ×26.5 B32923C3474+*** 480 500 510
0.56 8.5 ×16.5 ×26.5 B32923C3564M*** 480 500 510
0.68 10.5 ×18.5 ×26.5 B32923A2684M*** 390 400 540
0.68 10.5 ×20.5 ×26.5 B32923B2684+*** 390 400 540
0.68 10.5 ×16.5 ×26.5 B32923C3684+*** 390 400 540
0.82 10.5 ×18.5 ×26.5 B32923C3824M*** 390 400 540
1.0 12.0 ×22.0 ×26.5 B32923A2105M*** 450
1.0 11.0 ×20.5 ×26.5 B32923C3105+*** 370 350 510
1.5 12.0 ×22.0 ×26.5 B32923C3155M*** 450
1.5 14.5 ×29.5 ×26.5 B32923D3155+*** 260
2.2 14.5 ×29.5 ×26.5 B32923C3225+*** 260
B32921 ... B32926
X2 / 305 VAC
5
Ordering codes and packing units
Lead spacing
mm
CR
µF
Max. dimensions
w×h×l
mm
Ordering code
(composition see
below)
Ammo
pack
pcs./unit
Reel
pcs./unit
Untaped
pcs./unit
Composition of ordering code
+ = Capacitance tolerance code: *** = Packaging code:
M = ±20%
K = ±10%
289 = Ammo pack
189 = Reel
000 = Untaped (lead length 6 1 mm)
(Closer tolerances on request) Preferred types
27.5 0.68 11.0 ×19.0 ×31.5 B32924C3684+*** 350 320
0.82 11.0 ×19.0 ×31.5 B32924C3824+*** 350 320
1.0 11.0 ×21.0 ×31.5 B32924A2105+*** 350 320
1.0 11.0 ×19.0 ×31.5 B32924C3105+*** 350 320
1.5 13.5 ×23.0 ×31.5 B32924A2155M*** 250 260
1.5 14.0 ×24.5 ×31.5 B32924B2155+*** 260
1.5 12.5 ×21.5 ×31.5 B32924C3155+*** 300 280
2.2 18.0 ×27.5 ×31.5 B32924A2225+*** 200
2.2 14.0 ×24.5 ×31.5 B32924C3225+*** 260
3.3 21.0 ×31.0 ×31.5 B32924A2335M*** 180
3.3 18.0 ×27.5 ×31.5 B32924C3335M*** 200
3.3 16.0 ×32.0 ×31.5 B32924D3335+*** 220
4.7 22.0 ×36.5 ×31.5 B32924A2475M*** 160
4.7 18.0 ×33.0 ×31.5 B32924C3475M*** 200
4.7 21.0 ×31.0 ×31.5 B32924D3475M*** 180
5.6 22.0 ×36.5 ×31.5 B32924C3565+*** 160
37.5 2.2 14.0 ×25.0 ×41.5 B32926C3225+*** 115
3.3 18.0 ×32.5 ×41.5 B32926A2335+*** 90
3.3 16.0 ×28.5 ×41.5 B32926C3335+*** 100
4.7 20.0 ×39.5 ×41.5 B32926A2475M*** 75
4.7 18.0 ×32.5 ×41.5 B32926C3475+*** 90
5.6 20.0 ×39.5 ×41.5 B32926A2565M*** 75
5.6 18.0 ×32.5 ×41.5 B32926C3565+*** 90
6.8 28.0 ×42.5 ×41.5 B32926A2685M*** 55
6.8 20.0 ×39.5 ×41.5 B32926C3685+*** 75
8.2 28.0 ×42.5 ×41.5 B32926A2825M*** 55
8.2 20.0 × 39.5 × 41.5 B32926C3825+*** 55
10.0 28.0 ×42.5 ×41.5 B32926C3106+*** 55
B32921 ... B32926
X2 / 305 VAC
6
Technical data
Standard version (A/B/T): B3292*A.... / B3292*B.... / B3292*T....
Miniaturized version (C/D): B3292*C.... / B3292*D.... (preferred types)
Max. operating temperature Top,max +125 °C (for CR≤1µF with A/B/T version)
+110 °C (for CR>1 µF or C/D version)
Dissipation factor tan δ(in 10-3) CR≤0.1 µF 0.1µF<CR≤2.2 µF CR>2.2 µF
at 20 °C (upper limit values) at 1 kHz 1.0 1.0 2.0
100 kHz 5.0
Insulation resistance Rins CR≤0.33 µF CR>0.33 µF
or time constant τ= CRRins 100 000 MΩ30 000 s
at 20 °C, rel. humidity ≤65%
(minimum as-delivered values)
DC test voltage 2121 V, 2 s
Passive flammability category
to IEC 40 (CO) 752
B
Maximum continuous AC voltage VAC 310 V (50/60 Hz)
Rated AC voltage (IEC 60384-14) 305 V (50/60 Hz)
Maximum continuous DC voltage VDC 760 V (630 V for C/D version)
Operating AC voltage Vop at high TA≤110 °C Vop = VAC (continuously)
temperature TA≤110 °C Vop = 1.25 VAC (1000 h)
110 °C <TA≤125 °C Vop = VAC (1000 h) (only
for A/B/T version)
Damp heat test 56 days / 40 °C / 93% relative humidity
Limit values after damp heat test Capacitance change ∆C/C≤5%
Dissipation factor change ∆tan δ ≤ 0.5 10-3 (at 1 kHz)
Insulation resistance Rins ≤1.0 10-3 (at 10 kHz)
or time constant τ= CRRins ≥50% of minimum
as-delivered values
B32921 ... B32926
X2 / 305 VAC
7
Pulse handling capability
"dV/dt" represents the maximum permissible voltage change per unit of time for non-sinusoidal
voltages, expressed in V/µs.
"k0" represents the maximum permissible pulse characteristic of the waveform applied to the
capacitor, expressed in V2/µs.
Note:
The values of dV/dt and k0provided below must not be exceeded in order to avoid damaging the
capacitor.
dV/dt and k0values
Lead
spacing
10 mm 15 mm 22.5 mm 27.5 mm 37.5 mm
Version A/B/T C/D A/B/T C/D A/B/T C/D A/B/T C/D A/B/T C/D
dV/dt in
V/µs
550 475 400 340 200 170 150 120 100 80
k0in
V2/µs
473000 408500 344000 292400 172000 146200 129000 103200 86000 68800
Impedance Z versus frequency f
(typical values)
B32921 ... B32926
X2 / 305 VAC
8
Important notes
Page 9 of 9
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical
requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application. As a
rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them
than the customers themselves. For these reasons, it is always ultimately incumbent on the
customer to check and decide whether an EPCOS product with the properties described in the
product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of passive electronic components
or failure before the end of their usual service life cannot be completely ruled out in the
current state of the art, even if they are operated as specified. In customer applications
requiring a very high level of operational safety and especially in customer applications in which
the malfunction or failure of a passive electronic component could endanger human life or health
(e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of
suitable design of the customer application or other action taken by the customer (e.g. installation
of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the
event of malfunction or failure of a passive electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as “hazardous”). Useful information on this will be found in our
Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more
detailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order.
We also reserve the right to discontinue production and delivery of products. Consequently,
we cannot guarantee that all products named in this publication will always be available.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of
the “General Terms of Delivery for Products and Services in the Electrical Industry”
published by the German Electrical and Electronics Industry Association (ZVEI).
7. The trade names EPCOS, EPCOS-JONES, Baoke, CeraDiode, CSSP, MLSC, PhaseCap,
PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMID, SIOV, SIP5D, SIP5K, UltraCap,
WindCap are trademarks registered or pending in Europe and in other countries. Further
information will be found on the Internet at www.epcos.com/trademarks.
