5MP1 SERIES
Metallized
Polypropylene
Metallized Polypropylene
Metallized Polypropylene and Military Styles CFR13 and CFR14."Hi-Rel"
replacement for electrolytics for a broad range of commercial and military
switching power supplies.
FEATURES STANDARD CONFIGURATION
-Better electrical properties
with higher reliability and no
capacitance versus
electrolytic
-Resonant frequency of
1065KHz
-Ripple current to 30amps
-Capacitance as high as 50µf
-Voltage protection: 200%
-Long term stability, retrace
and low dielectric absorption
-5MP12/MIL Style CFR13 Wrap and
axial leads
-5MP16/MIL Style CFR14 Wrap and
lug terminations
Rev. 3
 Summary
Capacitance Range
1.0µF to 50.0µF. Capacitance is measured at 25°C at/or
referenced to a frequency of 1kHz.
Capacitance Tolerance
Standard tolerance is ±10%. Tolerances of ±20% and ±5% are
available.
Operating Temperature Range
-55°C to +105°C
Enclosure/ Construction
Mylar tape outer wrap.
Voltage Rating
DC working voltage ratings are from 100VDC to 400VDC
Quality Control
Capacitors are tested 100% for:
o Capacitance tolerance
o Dissipation Factor
o Dielectric withstanding voltage
o Insulation Resistance
o Equivalent Series Resistance (ESR)
Process and inspection data are maintained on and available
on special request.
Environmental
Parameter Method Condition
Vibration 204 D
Immersion 104 B
Shock 213 I
Humidity 106 -
Thermal Shock 107 A
Life 108 F
Reference MIL-STD-202
 Characteristics
Insulation Resistance
Temperature(°C) 25 85 105 
Megaohmsx
Microfarads
300,000 30,000 3,000
Insulation Resistance
Dilectric Strength
Capacitors shall withstand a DC potential of twice rated
voltage for one (1) minute through a limiting resistance
of 100 ohms/volt without damage or breakdown.
Capacitance Change
Temperature(°C) -55 25 105
PercentageChange
(typical)
2.0 0 -4.0
CapacitanceChange
Dissipation Factor
When measured at the frequency for capacitance
measurement, the dissipation factor shall not exceed 0.1%.
INSULATION RESISTANCE VERSUS
TEMPERATURE
100
1,000
10,000
100,000
1,000,000
+25° +45° +65° +85° +105°
TEMPERATURE (°C)
INSULATION RESISTANCE
(MEGOHMS X MICROFARAD)
CAPACITANCE CHANGE VERSUS
TEMPERATURE
-5
-4
-3
-2
-1
0
1
2
-55° - 3 5° - 15° +5° +2 5° +4 5° +6 5° +8 5° +10 5°
T E M P E R A T U R E ( °C )
CAPACITANCE CHANGE (%)
DISSIPATION FACTOR VERSUS TEMPERATURE
0
0 .0 1
0 .0 2
0 .0 3
0 .0 4
0 .0 5
-55° -3 5° -15° +5° +2 5° +4 5° +6 5° +8 5° +10 5°
T E M P E R A T U R E ( °C )
DISSIPATION FACTOR (%)
Rev. 3
ELECTRICAL DATA
EC PART
NUMBER
EQUIVALENT
MILITARY
DESIGNATION
CAP µF D L
ESR Ohms
20-100 kHz
Max
Fres
kHz
I PEAK
AMPS
dv/dt
(V/µs)
5MP12D105_ CFR13ALB105_ 1 0.469  ±0.062 0.750 0.015 1065 407 407
5MP12D205_ CFR13ALB205_ 2 0.534  ±0.062 0.938 0.012 703 528 264
5MP12D305_ CFR13ALB305_ 3 0.624  ±0.093 0.938 0.011 574 790 263
5MP12D505_ CFR13ALB505_ 5 0.640  ±0.093 1.250 0.100 385 828 166
5MP12D106_ CFR13ALB106_ 10 0.805  ±0.093 1.500 0.009 248 1280 128
5MP12D206_ CFR13ALB206_ 20 0.875  ±0.125 2.250 0.008 141 1517 76
5MP12D306_ CFR13ALB306_ 30 1.075  ±0.125 2.250 0.006 115 2277 76
5MP12D506_ Not Available 50 1.375  ±0.125 2.250 0.004 89 3795 76
5MP12F105_ CFR13ALC105_ 1 0.450  ±0.062 1.250 0.020 861 250 250
5MP12F205_ CFR13ALC205_ 2 0.605  ±0.093 1.250 0.015 609 498 249
5MP12F305_ CFR13ALC305_ 3 0.654  ±0.093 1.500 0.013 452 576 192
5MP12F505_ CFR13ALC505_ 5 0.769  ±0.093 1.750 0.011 323 782 156
5MP12F106_ CFR13ALC106_ 10 0.905  ±0.125 2.250 0.009 200 1139 114
5MP12F206_ CFR13ALC206_ 20 1.315  ±0.125 2.250 0.006 141 2277 114
5MP12J105_ CFR13ALE105_ 1 0.620  ±0.093 1.500 0.019 784 319 319
5MP12J205_ CFR13ALE205_ 2 0.802  ±0.093 1.750 0.015 511 521 260
5MP12J305_ CFR13ALE305_ 3 0.961  ±0.125 1.750 0.012 417 781 260
5MP12J505_ CFR13ALE505_ 5 1.067  ±0.125 2.250 0.010 283 950 190
5MP12J106_ CFR13ALE106_ 10 1.543  ±0.125 2.250 0.006 200 1898 190
Rev. 3
Lead
Dia.
0.032
0.032
0.040
0.040
0.040
0.040
0.040
0.040
0.032
0.032
0.040
0.040
0.040
0.040
0.040
0.040
0.040
0.040
0.040
Note: The tenth character of the EC part number represents the capacitance tolerance: M=±20%, K=±10%, J=±5%.
EC PART
NUMBER
EQUIVALENT
MILITARY
DESIGNATION
CAP µF D L
ESR Ohms
20-100 kHz
Max
Fres
kHz
I PEAK
AMPS
dv/dt
(V/µs)
5MP16D105_ CFR14LLB105_ 1 0.469  ±0.062 0.922 0.015 949 407 407
5MP16D205_ CFR14LLB205_ 2 0.534  ±0.062 1.110 0.012 617 528 264
5MP16D305_ CFR14LLB305_ 3 0.624  ±0.093 1.110 0.011 504 790 263
5MP16D505_ CFR14LLB505_ 5 0.640  ±0.093 1.422 0.100 347 828 166
5MP16D106_ CFR14LLB106_ 10 0.805  ±0.093 1.672 0.009 227 1280 128
5MP16D206_ CFR14LLB206_ 20 0.875  ±0.125 2.422 0.008 133 1517 76
5MP16D306_ CFR14LLB306_ 30 1.075  ±0.125
2.422
0.006 108 2277 76
5MP16D506_ Not Available 50 1.375  ±0.125
2.422
0.004
84
3795 76
5MP16F105_ CFR14LLC105_ 1 0.450  ±0.062 1.422 0.020 776 250 250
5MP16F205_ CFR14LLC205_ 2 0.605  ±0.093 1.422 0.015 548 498 249
5MP16F305_ CFR14LLC305_ 3 0.654  ±0.093
1.672
0.013
414
576 192
5MP16F505_ CFR14LLC505_ 5 0.769  ±0.093
1.922
0.011
299
782 156
5MP16F106_ CFR14LLC106_ 10 0.905  ±0.125 2.422 0.009
188
1139 114
5MP16F206_ CFR14LLC206_ 20 1.315  ±0.125
2.422
0.006 133 2277 114
5MP16J105_ CFR14LLE105_ 1 0.620  ±0.093 1.672 0.019 716 319 319
5MP16J205_ CFR14LLE205_ 2 0.802  ±0.093
1.922
0.015 472 521 260
5MP16J305_ CFR14LLE305_ 3 0.961  ±0.125
1.922
0.012
386
781 260
5MP16J505_ CFR14LLE505_ 5 1.067  ±0.125
2.422
0.010
265
950 190
5MP16J106_ CFR14LLE106_ 10 1.543  ±0.125 2.422 0.006 188 1898 190
L1
1.640
1.828
1.828
2.140
2.390
3.140
3.140
3.140
2.140
2.140
2.390
2.640
3.140
3.140
2.390
2.640
2.640
3.140
3.140
Note: The tenth character of the EC part number represents the capacitance tolerance: M=±20%, K=±10%, J=±5%.
EC PART
NUMBER
EQUIVALENT
MILITARY
DESIGNATION
MAXIMUM RIPPLE CURRENT (AMPS RMS) 20-100 kHz
CASE TEMPERATURE
25°C 35°C 45°C 55°C 65°C 75°C 85°C
5MP12D105_ CFR13ALB105_ 9.2 8.5 7.8 7.0 6.0 4.9 4.5
5MP12D205_ CFR13ALB205_ 10.8 10.0 9.1 8.2 7.0 5.8 5.3
5MP12D305_ CFR13ALB305_ 12.1 11.2 10.3 9.2 8.0 6.5 5.9
5MP12D505_ CFR13ALB505_ 13.8 12.7 11.6 10.4 9.0 7.4 6.7
5MP12D106_ CFR13ALB106_ 15.0 15.0 14.2 12.7 11.0 9.0 8.2
5MP12D206_ CFR13ALB206_ 15.0 15.0 15.0 15.0 13.6 11.1 10.0
5MP12D306_ CFR13ALB306_ 15.0 15.0 15.0 15.0 15.0 12.4 11.4
5MP12D506_ Not Available 15.0 15.0 15.0 15.0 15.0 13.6 12.4
5MP12F105_ CFR13ALC105_ 7.3 7.3 7.3 7.3 7.2 5.9 5.4
5MP12F205_ CFR13ALC205_ 12.0 12.0 11.3 10.1 8.7 7.1 6.5
5MP12F305_ CFR13ALC305_ 15.0 13.8 12.6 11.3 9.8 8.0 7.3
5MP12F505_ CFR13ALC505_ 15.0 15.0 14.7 13.1 11.4 9.3 8.5
5MP12F106_ CFR13ALC106_ 15.0 15.0 15.0 15.0 13.8 11.3 10.3
5MP12F206_ CFR13ALC206_ 15.0 15.0 15.0 15.0 15.0 14.1 12.8
5MP12J105_ CFR13ALE105_ 9.5 9.5 9.5 9.5 9.5 7.8 7.1
5MP12J205_ CFR13ALE205_ 15.0 15.0 15.0 13.4 11.6 9.5 8.7
5MP12J305_ CFR13ALE305_ 15.0 15.0 15.0 15.0 13.1 10.7 9.8
5MP12J505_ CFR13ALE505_ 15.0 15.0 15.0 15.0 15.0 12.5 11.4
5MP12J106_ CFR13ALE106_ 15.0 15.0 15.0 15.0 15.0 15.0 14.1
5MP16D105_ CFR14LLB105_ 10.3 9.5 8.7 7.8 6.7 5.5 5.0
5MP16D205_ CFR14LLB205_ 12.0 11.0 10.0 8.9 7.8 6.3 5.8
5MP16D305_ CFR14LLB305_ 13.3 12.3 11.2 10.0 8.7 7.1 6.5
5MP16D505_ CFR14LLB505_ 14.8 13.7 12.5 11.2 9.7 7.9 7.2
5MP16D106_ CFR14LLB106_ 17.8 16.5 15.0 13.5 11.7 9.5 8.7
5MP16D206_ CFR14LLB206_ 21.6 20.0 18.3 16.4 14.2 11.6 10.6
5MP16D306_ CFR14LLB306_ 24.3 22.5 20.5 18.4 15.9 13.0 11.9
5MP16D506_ Not Available 29.6 27.3 25.5 23.6 20.6 20.0 19.7
5MP16F105_ CFR14LLC105_ 7.3 7.3 7.3 7.3 7.3 6.4 5.8
5MP16F205_ CFR14LLC205_ 14.3 13.3 12.1 10.8 9.4 7.7 7.0
5MP16F305_ CFR14LLC305_ 15.9 14.7 13.5 12.0 10.4 8.5 7.8
5MP16F505_ CFR14LLC505_ 18.3 17.0 15.5 13.9 12.0 9.8 8.9
5MP16F106_ CFR14LLC106_ 22.4 20.7 18.9 16.9 14.6 12.0 10.9
5MP16F206_ CFR14LLC206_ 27.4 25.4 23.2 20.7 17.9 14.7 13.4
5MP16J105_ CFR14LLE105_ 9.5 9.5 9.5 9.5 9.5 8.3 7.5
5MP16J205_ CFR14LLE205_ 15.0 15.0 15.0 14.2 12.3 10.0 9.1
5MP16J305_ CFR14LLE305_ 21.1 19.5 17.8 15.9 13.8 11.3 10.3
5MP16J505_ CFR14LLE505_ 24.4 22.6 20.6 18.5 16.0 13.1 11.9
5MP16J106_ CFR14LLE106_ 30.0 27.8 25.4 22.7 19.7 16.1 14.7
Note: The tenth character of the EC part number represents the capacitance tolerance: M=±20%, K=±10%, J=±5%
Rev. 3
MECHANICAL DATA
Rev. 3
ADDITIONAL INFORMATION
These metallized polypropylene capacitors are manufactured by using special techniques in order to
achieve the optimum characteristics for high current, high capacitance, low ESR applications. For Filter
designs where capacitance of 50µF or less is suitable for the circuit, type 5MP the opportunity to
utilize capacitors with ESR's orders of magnitude better than those of electrolytics, thus providing the
opportunity to improve general system design. These unique capacitors also exhibit none of the
of capacitance with frequency often associated with electrolytics.
In addition to the features which make type 5MP particularly suitable for switching applications,
they are also characterized by low losses. Other advantages of polypropylene are long term
stability, retrace, low dielectric absorption, and high insulation resistance.
HOW TO ORDER
TYPE
Metallized Polypropylene 5MP1
STYLE / VOLTAGE
AC high power / D=100VDC; F=200VDC; J=400VDC 2 D
CAPACITANCE IN PICOFARADS
The two digits are the third represents the number of zeros
(e.g. 475=4700000pF)
105
TOLERANCE
Standard tolerance is ±10%. Tolerances of ±20% and ±5% are available. K
Marking and Date Code
All capacitors are marked with company initials "EC", corporate logo or EC trademark—in addition to type 5MP1, capacitance,
tolerance, rated DC working voltage and date code. The two digits of the date code represent the year, the second two digits the
week, i.e., 0952 is the 52nd week of 2009, 0902 is the second week of 2009.
Quality Assurance
Major emphasis is placed on quality assurance. EC is an ISO 9001-2000 and AS9100:2004 Company. Raw material
inspection and the use of SPC manufacturing procedures assure the highest quality standards. Procedures are fully described in the
EC Quality Control Manual. Electronic Concepts will continue to advance the state-of-the-art by utilizing leading edge technology,
compact capacitor designs and establishing reliability procedures.
Sales
United States Europe
Eastern:
*Headquarters*
P.O. Box 1278
Eatontown,NJ 07724
Tel: 732-542-7880
Fax: 732-542-0524
Central:
Illinois 630-668-8747
email: sales@ecicaps.com
website:www.ecicaps.com
Ireland
Electronic ConceptsEurope LTD
IDA Estate, Oughterad
Co. Galway, Ireland
tel: +353-91-552385,552432
fax: +353-91-552387
email: sales@ecicaps.ie
website:www.electronicconcepts.ie
Rev. 3