LM392 LM392 Low Power Operational Amplifier/Voltage Comparator Literature Number: SNOSBT5C LM392 Low Power Operational Amplifier/Voltage Comparator General Description The LM392 series consists of 2 independent building block circuits. One is a high gain, internally frequency compensated operational amplifier, and the other is a precision voltage comparator. Both the operational amplifier and the voltage comparator have been specifically designed to operate from a single power supply over a wide range of voltages. Both circuits have input stages which will commonmode input down to ground when operating from a single power supply. Operation from split power supplies is also possible and the low power supply current is independent of the magnitude of the supply voltage. Application areas include transducer amplifier with pulse shaper, DC gain block with level detector, VCO, as well as all conventional operational amplifier or voltage comparator circuits. Both circuits can be operated directly from the standard 5 VDC power supply voltage used in digital systems, and the output of the comparator will interface directly with either TTL or CMOS logic. In addition, the low power drain makes the LM392 extremely useful in the design of portable equipment. Advantages n Eliminates need for dual power supplies n An internally compensated op amp and a precision comparator in the same package n Allows sensing at or near ground n Power drain suitable for battery operation n Pin-out is the same as both the LM358 dual op amp and the LM393 dual comparator Features n Wide power supply voltage range Single supply: 3V to 32V Dual supply: 1.5V to 16V n Low supply current drain -- essentially independent of supply voltage: 600 A n Low input biasing current: 50 nA n Low input offset voltage: 2 mV n Low input offset current: 5 nA n Input common-mode voltage range includes ground n Differential input voltage range equal to the power supply voltage ADDITIONAL OP AMP FEATURES n Internally frequency compensated for unity gain n Large DC voltage gain: 100 dB n Wide bandwidth (unity gain): 1 MHz n Large output voltage swing: 0V to V+ - 1.5V ADDITIONAL COMPARATOR FEATURES n Low output saturation voltage: 250 mV at 4 mA n Output voltage compatible with all types of logic systems Connection Diagram (Amplifier A = Comparator) (Amplifier B = Operational Amplifier) Dual-In-Line Package 00779301 (Top View) Order Number LM392M or LM392MX See NS Package Number M08A Order Number LM392N See NS Package Number N08E (c) 2004 National Semiconductor Corporation DS007793 www.national.com LM392 Low Power Operational Amplifier/Voltage Comparator August 2000 LM392 Distributors for availability and specifications. Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ LM392 Supply Voltage, V+ 32V or 16V Differential Input Voltage 32V Input Voltage -0.3V to +32V Power Dissipation (Note 2) Molded DIP (LM392N) 820 mW Small Outline Package (LM392M) 530 mW Output Short-Circuit to Ground (Note 3) Continuous Input Current (VIN < -0.3 VDC) (Note 4) 50 mA Operating Temperature Range 0C to +70C Storage Temperature Range -65C to +150C Lead Temperature (Soldering, 10 seconds) 260C ESD rating to be determined. Soldering Information Dual-in-Line Package Soldering (10 seconds) 260C Small Outline Package Vapor Phase (60 seconds) 215C Infrared (15 seconds) 220C See AN-450 "Surface Mounting Methods and Their Effect on Product Reliability" for other methods of soldering surface mount devices. Electrical Characteristics (V+ = 5 VDC; specifications apply to both amplifiers unless otherwise stated) (Note 5) Parameter Conditions LM392 Min Units Typ Max Input Offset Voltage TA = 25C, (Note 6) 2 5 mV Input Bias Current IN(+) or IN(-), TA =25C, (Note 7) , VCM = 0V 50 250 nA 5 Input Offset Current IN(+) - IN(-), TA = 25C Input Common-Mode Voltage Range V+ = 30 VDC, TA = 25C, (Note 8) Supply Current RL = , V = 30 V Supply Current RL = , V+= 5 V Amplifier-to-Amplifier Coupling f = 1 kHz to 20 kHz, TA = 25C, Input Referred, (Note 9) 50 nA V+-1.5 V 1 2 mA 0.5 1 mA 0 + -100 dB Input Offset Voltage (Note 6) 7 Input Bias Current IN(+) or IN(-) 400 nA Input Offset Current IN(+) - IN(-) 150 nA Input Common-Mode Voltage Range V+ = 30 VDC, (Note 8) V+-2 V Differential Input Voltage Keep All VIN' 0 VDC (or V , if used ) (Note 10) 32 V www.national.com 0 s - 2 mV LM392 Electrical Characteristics (Continued) (V+ = 5 VDC; specifications apply to both amplifiers unless otherwise stated) (Note 5) Parameter Conditions LM392 Min Typ 100 Units Max OP AMP ONLY Large Signal Voltage Gain V+ = 15 VDC, Vo swing = 1 VDC to 11 VDC, RL = 2 k, TA = 25C 25 Output Voltage Swing RL = 2 k, TA = 25C 0 + V/mV V+-1.5 V Common-Mode Rejection Ratio DC, TA = 25C, VCM= 0, VDC to V -1.5 VDC 65 70 dB Power Supply Rejection Ratio DC, TA = 25C 65 100 dB Output Current Source VIN(+) = 1 VDC, VIN(-) = 0 VDC, V+ = 15 VDC, Vo = 2 VDC, TA = 25C 20 40 mA Output Current Sink VIN(-) = 1 VDC, VIN(+) = 0 VDC, V+ = 15 VDC, Vo =2VDC, TA = 25C 10 20 mA VIN(-) = 1 VDC, VIN(+) = 0 VDC, V+ = 15 VDC, Vo =200 mV, TA = 25C 12 50 A Input Offset Voltage Drift RS = 0 7 V/C Input Offset Current Drift RS = 0 10 pADC/C 200 V/mV 300 ns COMPARATOR ONLY Voltage Gain RL 15 k, V+ = 15 VDC, TA = 25C Large Signal Response Time VIN = TTL Logic Swing, VREF = 1.4 VDC VRL = 5 VDC, RL = 5.1 k, TA = 25C Response Time VRL = 5 VDC, RL = 5.1 k, TA = 25C Output Sink Current VIN(-) =1 VDC, VIN(+) = 0 VDC, VO 1.5 VDC, TA = 25C Saturation Voltage VIN(-) 1 VDC, VIN(+) = 0, ISINK 4 mA, TA = 25C 50 6 1.3 s 16 mA 250 VIN(-) 1 VDC, VIN(+) = 0, ISINK 4 mA Output Leakage Current VIN(-) = 0, VIN(+) 1 VDC, Vo = 5 VDC, TA = 25C VIN(-) = 0, VIN(+) 1 VDC, Vo = 30 VDC 400 mV 700 mV 0.1 nA 1.0 A Note 1: "Absolute Maximum Ratings" indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. Note 2: For operating at temperatures above 25C, the LM392 must be derated based on a 125C maximum junction temperature and a thermal resistance of 122C/W which applies for the device soldered in a printed circuit board, operating in still air ambient. The dissipation is the total of both amplifiers -- use external resistors, where possible, to allow the amplifier to saturate or to reduce the power which is dissipated in the integrated circuit. Note 3: Short circuits from the output to V+ can cause excessive heating and eventual destruction. When considering short circuits to ground, the maximum output current is approximately 40 mA for the op amp and 30 mA for the comparator independent of the magnitude of V+. At values of supply voltage in excess of 15V, continuous short circuits can exceed the power dissipation ratings and cause eventual destruction. Note 4: This input current will only exist when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of the input PNP transistors becoming forward biased and thereby acting as input diode clamps. In addition to this diode action, there is also lateral NPN parasitic transistor action on the IC chip. This transistor action can cause the output voltages of the amplifiers to go to the V+ voltage level (or to ground for a large overdrive) for the time duration that an input is driven negative. This is not destructive and normal output states will re-establish when the input voltage, which was negative, again returns to a value greater than -0.3V (at 25C). Note 5: These specifications apply for V+ = 5V, unless otherwise stated. For the LM392, temperature specifications are limited to 0C TA +70C. Note 6: At output switch point, VO . 1.4V, RS = 0 with V+ from 5V to 30V; and over the full input common-mode range (0V to V+ - 1.5V). Note 7: The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the output so no loading change exists on the input lines. Note 8: The input common-mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end of the common-mode voltage range is V+ - 1.5V, but either or both inputs can go to 32V without damage. Note 9: Due to proximity of external components, insure that coupling is not originating via the stray capacitance between these external parts. This typically can be detected as this type of capacitive coupling increases at higher frequencies. Note 10: Positive excursions of input voltage may exceed the power supply level. As long as the other input voltage remains within the common-mode range, the comparator will provide a proper output state. The input voltage to the op amp should not exceed the power supply level. The input voltage state must not be less than -0.3V (or 0.3V below the magnitude of the negative power supply, if used) on either amplifier. Note 11: The response time specified is for a 100 mV input step with 5 mV overdrive. For larger overdrive signals 300 ns can be obtained. 3 www.national.com LM392 Schematic Diagram 00779302 Application Hints Please refer to the application hints section of the LM193 and the LM158 datasheets. www.national.com 4 LM392 Physical Dimensions inches (millimeters) unless otherwise noted S.O. Package (M) Order Number LM392M or LM392MX NS Package Number M08A Molded Dual-In-Line Package (N) Order Number LM392N NS Package Number N08E 5 www.national.com LM392 Low Power Operational Amplifier/Voltage Comparator Notes LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ``Banned Substances'' as defined in CSP-9-111S2. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated