Angle Sensor GMR-Based Angle Sensor TLE5012B Data Sheet Rev. 2.0, 2014-02 Sense & Control TLE5012B Data Sheet 2 Rev. 2.0, 2014-02 TLE5012B Revision History Page or Item Subjects (major changes since previous revision) Rev. 2.0, 2014-02 All chapters revised Trademarks of Infineon Technologies AG AURIXTM, C166TM, CanPAKTM, CIPOSTM, CIPURSETM, EconoPACKTM, CoolMOSTM, CoolSETTM, CORECONTROLTM, CROSSAVETM, DAVETM, DI-POLTM, EasyPIMTM, EconoBRIDGETM, EconoDUALTM, EconoPIMTM, EconoPACKTM, EiceDRIVERTM, eupecTM, FCOSTM, HITFETTM, HybridPACKTM, IRFTM, ISOFACETM, IsoPACKTM, MIPAQTM, ModSTACKTM, my-dTM, NovalithICTM, OptiMOSTM, ORIGATM, POWERCODETM; PRIMARIONTM, PrimePACKTM, PrimeSTACKTM, PRO-SILTM, PROFETTM, RASICTM, ReverSaveTM, SatRICTM, SIEGETTM, SINDRIONTM, SIPMOSTM, SmartLEWISTM, SOLID FLASHTM, TEMPFETTM, thinQ!TM, TRENCHSTOPTM, TriCoreTM. Other Trademarks Advance Design SystemTM (ADS) of Agilent Technologies, AMBATM, ARMTM, MULTI-ICETM, KEILTM, PRIMECELLTM, REALVIEWTM, THUMBTM, VisionTM of ARM Limited, UK. AUTOSARTM is licensed by AUTOSAR development partnership. BluetoothTM of Bluetooth SIG Inc. CAT-iqTM of DECT Forum. COLOSSUSTM, FirstGPSTM of Trimble Navigation Ltd. EMVTM of EMVCo, LLC (Visa Holdings Inc.). EPCOSTM of Epcos AG. FLEXGOTM of Microsoft Corporation. FlexRayTM is licensed by FlexRay Consortium. HYPERTERMINALTM of Hilgraeve Incorporated. IECTM of Commission Electrotechnique Internationale. IrDATM of Infrared Data Association Corporation. ISOTM of INTERNATIONAL ORGANIZATION FOR STANDARDIZATION. MATLABTM of MathWorks, Inc. MAXIMTM of Maxim Integrated Products, Inc. MICROTECTM, NUCLEUSTM of Mentor Graphics Corporation. MIPITM of MIPI Alliance, Inc. MIPSTM of MIPS Technologies, Inc., USA. muRataTM of MURATA MANUFACTURING CO., MICROWAVE OFFICETM (MWO) of Applied Wave Research Inc., OmniVisionTM of OmniVision Technologies, Inc. OpenwaveTM Openwave Systems Inc. RED HATTM Red Hat, Inc. RFMDTM RF Micro Devices, Inc. SIRIUSTM of Sirius Satellite Radio Inc. SOLARISTM of Sun Microsystems, Inc. SPANSIONTM of Spansion LLC Ltd. SymbianTM of Symbian Software Limited. TAIYO YUDENTM of Taiyo Yuden Co. TEAKLITETM of CEVA, Inc. TEKTRONIXTM of Tektronix Inc. TOKOTM of TOKO KABUSHIKI KAISHA TA. UNIXTM of X/Open Company Limited. VERILOGTM, PALLADIUMTM of Cadence Design Systems, Inc. VLYNQTM of Texas Instruments Incorporated. VXWORKSTM, WIND RIVERTM of WIND RIVER SYSTEMS, INC. ZETEXTM of Diodes Zetex Limited. Last Trademarks Update 2011-11-11 Data Sheet 3 Rev. 2.0, 2014-02 TLE5012B Table of Contents Table of Contents Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 List of Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 1 1.1 1.2 1.3 Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Application Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2.1 2.2 2.2.1 2.2.2 2.2.3 2.2.4 2.2.5 2.2.6 2.3 2.4 2.5 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Functional Block Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internal Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Oscillator and PLL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SD-ADC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Digital Signal Processing Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensing Principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Application Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 4 4.1 4.2 4.3 4.3.1 4.3.2 4.3.3 4.3.4 4.3.5 4.3.6 4.3.7 4.4 4.4.1 4.4.1.1 4.4.1.2 4.4.2 4.4.3 4.4.3.1 4.4.3.2 4.4.3.3 4.4.4 4.4.5 4.5 4.5.1 4.6 4.6.1 Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operating Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Input/Output characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ESD Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GMR Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Angle Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Autocalibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Signal Processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Clock Supply (CLK Timing Definition) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Synchronous Serial Communication (SSC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SSC Timing Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SSC Data Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pulse Width Modulation (PWM) Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Short PWM Code (SPC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unit Time Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Master Trigger Pulse Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Checksum Nibble Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hall Switch Mode (HSM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Incremental Interface (IIF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Test Mechanisms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ADC Test Vectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Supply Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internal Supply Voltage Comparators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Data Sheet 4 8 8 9 9 10 10 10 10 10 11 11 11 11 12 14 14 19 19 19 21 21 23 23 24 25 26 28 29 29 29 31 34 36 37 38 38 39 42 43 43 44 45 Rev. 2.0, 2014-02 TLE5012B Table of Contents 4.6.2 4.6.3 4.6.4 VDD Overvoltage Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 GND - Off Comparator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 VDD - Off Comparator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 5 5.1 5.2 5.3 5.4 5.5 Pre-Configured Derivates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IIF-type: E1000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HSM-type: E3005 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PWM-type: E5000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PWM-type: E5020 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPC-type: E9000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 46 46 46 46 46 6 6.1 6.2 6.3 6.4 6.5 Package Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Package Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Package Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Footprint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Packing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 47 47 48 49 49 Data Sheet 5 Rev. 2.0, 2014-02 TLE5012B List of Figures List of Figures Figure 1-1 Figure 2-1 Figure 2-2 Figure 2-3 Figure 2-4 Figure 3-1 Figure 3-2 Figure 3-3 Figure 3-4 Figure 3-5 Figure 3-6 Figure 3-7 Figure 4-1 Figure 4-2 Figure 4-3 Figure 4-4 Figure 4-5 Figure 4-6 Figure 4-7 Figure 4-8 Figure 4-9 Figure 4-10 Figure 4-11 Figure 4-12 Figure 4-13 Figure 4-14 Figure 4-15 Figure 4-16 Figure 4-17 Figure 4-18 Figure 4-19 Figure 4-20 Figure 4-21 Figure 4-22 Figure 4-23 Figure 4-24 Figure 6-1 Figure 6-2 Figure 6-3 Figure 6-4 Data Sheet PG-DSO-8 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 TLE5012B block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Sensitive bridges of the GMR sensor (not to scale) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Ideal output of the GMR sensor bridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Pin configuration (top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Application circuit for TLE5012B with IIF interface and SSC (using internal CLK) . . . . . . . . . . . . . 15 Application circuit for TLE5012B with HS Mode and SSC (using internal CLK) . . . . . . . . . . . . . . . 15 Application circuit for TLE5012B with only PWM interface (using internal CLK) . . . . . . . . . . . . . . 16 Application circuit for TLE5012B with only PWM interface (using internal CLK) . . . . . . . . . . . . . . 16 Application circuit for TLE5012B with only SPC interface (using internal CLK) . . . . . . . . . . . . . . . 17 SSC configuration in sensor-slave mode with push-pull outputs (high-speed application) . . . . . . 17 SSC configuration in sensor-slave mode and open-drain (bus systems) . . . . . . . . . . . . . . . . . . . . 18 Allowed magnetic field range as function of junction temperature.. . . . . . . . . . . . . . . . . . . . . . . . . 20 Offset and amplitude definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Additional angle error for temperature changes above 5 Kelvin within 1.5 revolutions . . . . . . . . . 25 Signal path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Delay of sensor output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 External CLK timing definition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 SSC timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 SSC data transfer (data-read example) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 SSC data transfer (data-write example) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 SSC bit ordering (read example) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Update of update registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Fast CRC polynomial division circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Typical example of a PWM signal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 SPC frame example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 SPC pause timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 SPC Master pulse timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Hall Switch Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 HS hysteresis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Incremental interface with A/B mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Incremental interface with Step/Direction mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 ADC test vectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Overvoltage comparator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 GND - off comparator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 VDD - off comparator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 PG-DSO-8 package dimension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Position of sensing element . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Footprint of PG-DSO-8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Tape and Reel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 6 Rev. 2.0, 2014-02 TLE5012B List of Tables List of Tables Table 1-1 Table 2-1 Table 4-1 Table 4-2 Table 4-3 Table 4-4 Table 4-5 Table 4-6 Table 4-7 Table 4-8 Table 4-9 Table 4-10 Table 4-11 Table 4-12 Table 4-13 Table 4-14 Table 4-15 Table 4-16 Table 4-17 Table 4-18 Table 4-19 Table 4-20 Table 4-21 Table 4-22 Table 4-23 Table 4-24 Table 4-25 Table 4-26 Table 6-1 Table 6-2 Data Sheet Derivate Ordering codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Operating range and parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Input voltage and output currents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Driver strength characteristic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Electrical parameters for 4.5 V < VDD < 5.5 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Electrical parameters for 3.0 V < VDD < 3.6 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 ESD protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Basic GMR parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Angle performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Signal processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Internal clock timing specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 External Clock Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 SSC push-pull timing specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 SSC open-drain timing specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Structure of the Command Word . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Structure of the Safety Word . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Bit Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 PWM interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Frame configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Structure of status nibble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Predivider setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Master pulse parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Hall Switch Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Incremental Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 ADC test vectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Test comparator threshold voltages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Package Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Sensor IC placement tolerances in package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 7 Rev. 2.0, 2014-02 TLE5012B Product Description 1 Product Description Figure 1-1 PG-DSO-8 package 1.1 Overview The TLE5012B is a 360 angle sensor that detects the orientation of a magnetic field. This is achieved by measuring sine and cosine angle components with monolithic integrated Giant Magneto Resistance (iGMR) elements. These raw signals (sine and cosine) are digitally processed internally to calculate the angle orientation of the magnetic field (magnet). The TLE5012B is a pre-calibrated sensor. The calibration parameters are stored in laser fuses. At start-up the values of the fuses are written into flip-flops, where these values can be changed by the application-specific parameters. Further precision of the angle measurement over a wide temperature range and a long lifetime can be improved by enabling an optional internal autocalibration algorithm. Data communications are accomplished with a bi-directional Synchronous Serial Communication (SSC) that is SPI-compatible. The sensor configuration is stored in registers, which are accessible by the SSC interface. Additionally four other interfaces are available with the TLE5012B: Pulse-Width-Modulation (PWM) Protocol, Short-PWM-Code (SPC) Protocol, Hall Switch Mode (HSM) and Incremental Interface (IIF). These interfaces can be used in parallel with SSC or alone. Pre-configured sensor derivates with different interface settings are available (see Table 1-1 and Chapter 5) Online diagnostic functions are provided to ensure reliable operation. Table 1-1 Derivate Ordering codes Product Type Marking Ordering Code Package TLE5012B E1000 012B1000 SP001166960 PG-DSO-8 TLE5012B E3005 012B3005 SP001166964 PG-DSO-8 TLE5012B E5000 012B5000 SP001166968 PG-DSO-8 TLE5012B E5020 012B5020 SP001166972 PG-DSO-8 TLE5012B E9000 012B9000 SP001166998 PG-DSO-8 Note: See Chapter 5 for description of derivates. Data Sheet 8 Rev. 2.0, 2014-02 TLE5012B Product Description 1.2 * * * * * * * * * * * * * * * * * Features Giant Magneto Resistance (GMR)-based principle Integrated magnetic field sensing for angle measurement 360 angle measurement with revolution counter and angle speed measurement Two separate highly accurate single bit SD-ADC 15 bit representation of absolute angle value on the output (resolution of 0.01) 16 bit representation of sine / cosine values on the interface Max. 1.0 angle error over lifetime and temperature-range with activated auto-calibration Bi-directional SSC Interface up to 8Mbit/s Supports Safety Integrity Level (SIL) with diagnostic functions and status information Interfaces: SSC, PWM, Incremental Interface (IIF), Hall Switch Mode (HSM), Short PWM Code (SPC, based on SENT protocol defined in SAE J2716) Output pins can be configured (programmed or pre-configured) as push-pull or open-drain Bus mode operation of multiple sensors on one line is possible with SSC or SPC interface in open-drain configuration 0.25 m CMOS technology Automotive qualified: -40C to 150C (junction temperature) ESD > 4kV (HBM) RoHS compliant (Pb-free package) Halogen-free 1.3 Application Example The TLE5012B GMR-based angle sensor is designed for angular position sensing in automotive applications such as: * * * * Electrical commutated motor (e.g. used in Electric Power Steering (EPS)) Rotary switches Steering angle measurements General angular sensing Data Sheet 9 Rev. 2.0, 2014-02 TLE5012B Functional Description 2 Functional Description 2.1 Block Diagram TLE5012B VDD VRG VRA VRD GND X GMR SDADC Digital Signal Processing Unit CSQ SSC Interface SCK DATA Y GMR SDADC Temp SDADC ISM CORDIC CCU RAM Fuses Incremental IF PWM HSM SPC Osc IFA IFB IFC PLL Figure 2-1 TLE5012B block diagram 2.2 Functional Block Description 2.2.1 Internal Power Supply The internal stages of the TLE5012B are supplied with several voltage regulators: * * * GMR Voltage Regulator, VRG Analog Voltage Regulator, VRA Digital Voltage Regulator, VRD (derived from VRA) These regulators are directly connected to the supply voltage VDD. 2.2.2 Oscillator and PLL The digital clock of the TLE5012B is given by the Phase-Locked Loop (PLL), which is by default fed by an internal oscillator. In order to synchronize the TLE5012B with other ICs in a system, the TLE5012B can be configured via Data Sheet 10 Rev. 2.0, 2014-02 TLE5012B Functional Description SSC interface to use an external clock signal supplied on the IFC pin as source for the PLL, instead of the internal clock. External clock mode is only available in PWM or SPC interface configuration. 2.2.3 SD-ADC The Sigma-Delta Analog-Digital-Converters (SD-ADC) transform the analog GMR voltages and temperature voltage into the digital domain. 2.2.4 Digital Signal Processing Unit The Digital Signal Processing Unit (DSPU) contains the: * * * * * Intelligent State Machine (ISM), which does error compensation of offset, offset temperature drift, amplitude synchronicity and orthogonality of the raw signals from the GMR bridges, and performs additional features such as auto-calibration, prediction and angle speed calculation COordinate Rotation DIgital Computer (CORDIC), which contains the trigonometric function for angle calculation Capture Compare Unit (CCU), which is used to generate the PWM and SPC signals Random Access Memory (RAM), which contains the configuration registers Laser Fuses, which contain the calibration parameters for the error-compensation and the IC default configuration, which is loaded into the RAM at startup 2.2.5 Interfaces Bi-directional communication with the TLE5012B is enabled by a three-wire SSC interface. In parallel to the SSC interface, one secondary interface can be selected, which is available on the IFA, IFB, IFC pins: * * * * PWM Incremental Interface Hall Switch Mode Short PWM Code By using pre-configured derivates (see Chapter 5), the TLE5012B can also be operated with the secondary interface only, without SSC communication. 2.2.6 Safety Features The TLE5012B offers a multiplicity of safety features to support the Safety Integrity Level (SIL) and it is a PROSILTM product. Safety features are: * * * * * * Test vectors switchable to ADC input (activated via SSC interface) Inversion or combination of filter input streams (activated via SSC interface) Data transmission check via 8-bit Cyclic Redundancy Check (CRC) for SSC communcation and 4-bit CRC nibble for SPC interface Built-in Self-test (BIST) routines for ISM, CORDIC, CCU, ADCs run at startup Two independent active interfaces possible Overvoltage and undervoltage detection Disclaimer PRO-SILTM is a Registered Trademark of Infineon Technologies AG. The PRO-SILTM Trademark designates Infineon products which contain SIL Supporting Features. SIL Supporting Features are intended to support the overall System Design to reach the desired SIL (according to IEC61508) or A-SIL (according to ISO26262) level for the Safety System with high efficiency. Data Sheet 11 Rev. 2.0, 2014-02 TLE5012B Functional Description SIL respectively A-SIL certification for such a System has to be reached on system level by the System Responsible at an accredited Certification Authority. SIL stands for Safety Integrity Level (according to IEC 61508) A-SIL stands for Automotive-Safety Integrity Level (according to ISO 26262) 2.3 Sensing Principle The Giant Magneto Resistance (GMR) sensor is implemented using vertical integration. This means that the GMR-sensitive areas are integrated above the logic part of the TLE5012B device. These GMR elements change their resistance depending on the direction of the magnetic field. Four individual GMR elements are connected to one Wheatstone sensor bridge. These GMR elements sense one of two components of the applied magnetic field: * * X component, Vx (cosine) or the Y component, Vy (sine) With this full-bridge structure the maximum GMR signal is available and temperature effects cancel out each other. GMR Resistors S 0 VX VY N ADCX + ADCX - GND ADCY+ ADCY- VDD 90 Figure 2-2 Sensitive bridges of the GMR sensor (not to scale) Attention: Due to the rotational placement inaccuracy of the sensor IC in the package, the sensors 0 position may deviate by up to 3 from the package edge direction indicated in Figure 2-2. In Figure 2-2, the arrows in the resistors represent the magnetic direction which is fixed in the reference layer. If the external magnetic field is parallel to the direction of the Reference Layer, the resistance is minimal. If they are anti-parallel, resistance is maximal. The output signal of each bridge is only unambiguous over 180 between two maxima. Therefore two bridges are oriented orthogonally to each other to measure 360. With the trigonometric function ARCTAN2, the true 360 angle value is calculated out of the raw X and Y signals from the sensor bridges. Data Sheet 12 Rev. 2.0, 2014-02 TLE5012B Functional Description Y Component (SIN) VY X Component (COS) VX V VX (COS) 0 90 180 270 360 Angle VY (SIN) Figure 2-3 Ideal output of the GMR sensor bridges Data Sheet 13 Rev. 2.0, 2014-02 TLE5012B Functional Description 2.4 Pin Configuration 8 7 6 5 1 2 3 4 Center of Sensitive Area Figure 2-4 Pin configuration (top view) 2.5 Pin Description Table 2-1 Pin Description Pin No. Symbol In/Out Function 1 IFC (CLK / IIF_IDX / HS3) I/O Interface C: External Clock1) / IIF Index / Hall Switch Signal 3 2 SCK I SSC Clock 3 CSQ I SSC Chip Select 4 DATA I/O SSC Data 5 IFA I/O (IIF_A / HS1 / PWM / SPC) Interface A: IIF Phase A / Hall Switch Signal 1 / PWM / SPC output (input for SPC trigger only) 6 VDD - Supply Voltage 7 GND - Ground 8 IFB (IIF_B / HS2) O Interface B: IIF Phase B / Hall Switch Signal 2 1) External clock feature is not available in IIF or HSM interface mode Data Sheet 14 Rev. 2.0, 2014-02 TLE5012B Application Circuits 3 Application Circuits The application circuits in this chapter show the various communication possibilities of the TLE5012B. The pin output mode configuration is device-specific and it can be either push-pull or open-drain. The bit IFAB_OD (register IFAB, 0DH) indicates the output mode for the IFA, IFB and IFC pins. The SSC pins are by default pushpull (bit SSC_OD, register MOD_3, 09H). Figure 3-1 shows a basic block diagram of a TLE5012B with Incremental Interface and SSC configuration. The derivate TLE5012B - E1000 is by default configured with push-pull IFA (IIF_A), IFB (IIF_ B) and IFC (IIF_IDX) pins. VDD (3.0 - 5.5V) TLE5012B 100nF VRG VRA VRD X GMR SDADC Digital Signal Processing Unit Y GMR SDADC SDADC SSC Interface *) SCK *) DATA **) SSC ISM IFA (IIF _A) CORDIC CCU Temp CSQ RAM Incremental IF PWM HSM Fuses Osc PLL IFB (IIF _B) IIF IFC (IIF_IDX) GND *) recommended , e.g. 100 **) recommended , e.g. 470 Figure 3-1 Application circuit for TLE5012B with IIF interface and SSC (using internal CLK) In case that the IFA, IFB and IFC pins are configurated via the SSC interface as open-drain pins, three resistors (one for each line) between output line and VDD would be recommended (e.g. 2.2k). Figure 3-2 shows a basic block diagram of the TLE5012B with HS Mode and SSC configuration. The derivate TLE5012B - E3005 is by default configurated with push-pull IFA (HS1), IFB (HS2) and IFC (HS3) pins. VDD (3.0 - 5.5V) TLE 5012B 100nF VRG VRA VRD X GMR SDADC Digital Signal Processing Unit Y GMR SDADC SDADC *) SCK *) DATA **) SSC ISM IFA (HS1) CORDIC CCU Temp SSC Interface CSQ RAM Incremental IF PWM HSM Fuses Osc PLL IFB (HS2) HSM IFC (HS3) GND *) recommended , e.g. 100 **) recommended , e.g. 470 Figure 3-2 Application circuit for TLE5012B with HS Mode and SSC (using internal CLK) Data Sheet 15 Rev. 2.0, 2014-02 TLE5012B Application Circuits In case that the IFA, IFB and IFC pins are configurated via the SSC interface as open drain pins, three resistors (one for each line) between the output line and VDD would be recommended (e.g. 2.2k). The TLE5012B can be configured with PWM only (Figure 3-3). The derivate TLE5012B - E5000 is by default configurated with push-pull IFA (PWM) pin. Therefore the following configuration is recommended: VDD (3.0 - 5.5V) TLE5012B 100 nF VRG VRA VRD X GMR SDADC Digital Signal Processing Unit Y GMR SDADC Temp SSC Interface SCK *) DATA ISM IFA (PWM) CORDIC CCU SDADC CSQ RAM Incremental IF PWM HSM Fuses Osc PLL IFB IFC GND *) recommended , e.g. 10.0k Figure 3-3 Application circuit for TLE5012B with only PWM interface (using internal CLK) The TLE5012B - E5020 is also a PWM derivate but with open drain IFA (PWM) pin. A pull-up resistor (e.g. 2.2k) should then be added between the IFA line and VDD, as shown in Figure 3-4. VDD (3.0 - 5.5V) TLE 5012B 100nF VRG VRA VRD *) X GMR SDADC Y GMR SDADC Temp SDADC Digital Signal Processing Unit CSQ SSC Interface SCK DATA **) ISM IFA (PWM) CORDIC CCU RAM Incremental IF PWM HSM Fuses Osc PLL IFB IFC GND *) recommended , e.g. 2.2k **) recommended , e.g. 10.0k Figure 3-4 Application circuit for TLE5012B with only PWM interface (using internal CLK) For safety reasons it is better that the non-used pins are connected to ground, rather than floating. A resistor between he DATA line pin and ground is recommended to avoid shortcuts if DATA generates any unexpected output. The CSQ line has to be connected to VDD to avoid unintentional activation of the SSC interface. Data Sheet 16 Rev. 2.0, 2014-02 TLE5012B Application Circuits The TLE5012B can be configured with SPC only (Figure 3-5). This is only possible with the TLE5012B - E9000 derivate, which is by default configurated with an open-drain IFA (SPC) pin. VDD (3.0 - 5.5V) TLE5012B 100nF VRG VRA VRD *) X GMR SDADC Y GMR SDADC Temp SDADC Digital Signal Processing Unit CSQ SSC Interface SCK (S_NR[0]) **) DATA ISM IFA (SPC ) CORDIC Incremental IF PWM HSM CCU RAM Fuses Osc PLL IFB IFC (S_NR[1]) GND *) recommended , e.g. 2.2k **) recommended , e.g. 10.0k Figure 3-5 Application circuit for TLE5012B with only SPC interface (using internal CLK) In Figure 3-5 the IFC (S_NR[1]) and SCK (S_NR[0]) pins are set to ground to generate the slave number (S_NR) 0D (or 00B). For safety reasons it is better that the non-used pins are connected to ground, rather than floating. A resistor between the DATA line pin and ground is recommended to avoid shortcuts if DATA generates any unexpected output. The CSQ line has to be connected to VDD to avoid unintentional activation of the SSC interface. Synchronous Serial Communication (SSC) configuration In Figure 3-1 and Figure 3-2 the SSC interface has the default push-pull configuration (see details in Figure 3-6). Series resistors on the DATA, SCK (serial clock signal) and CSQ (chip select) lines are recommended to limit the current in the erroneous case that either the sensor pushes high and the microcontroller pulls low at the same time or vice versa. The resistors in the SCK and CSQ lines are only necessary in case of disturbances or noise. (SSC Slave) TLE 5012B C (SSC Master) DATA Shift Reg. **) MTSR EN MRST SCK CSQ *) SCK *) CSQ Shift Reg. EN Clock Gen. *) optional , e.g. 100 **) optional , e.g. 470 Figure 3-6 SSC configuration in sensor-slave mode with push-pull outputs (high-speed application) Data Sheet 17 Rev. 2.0, 2014-02 TLE5012B Application Circuits It is also possible to use an open-drain setup for the DATA, SCK and CSQ lines. This setup is designed to communicate with a microcontroller in a bus system, together with other SSC slaves (e.g. two TLE5012B devices for redundancy reasons). This mode can be activated using the bit SSC_OD. The open-drain configuration can be seen in Figure 3-7. Series resistors on the DATA, SCK, and CSQ lines are recommended to limit the current in case either the microcontroller or the sensor are accidentally switched to pushpull. A pull-up resistor of typ. 1 k is required on the DATA line. (SSC Slave) TLE 5012B C (SSC Master) typ. 1k Shift Reg. DATA *) *) MRST Shift Reg. MTSR SCK *) CSQ *) SCK Clock Gen. CSQ *) optional , e.g. 100 Figure 3-7 SSC configuration in sensor-slave mode and open-drain (bus systems) Data Sheet 18 Rev. 2.0, 2014-02 TLE5012B Specification 4 Specification 4.1 Absolute Maximum Ratings Table 4-1 Absolute maximum ratings Parameter Symbol Values Min. Typ. Unit Note / Test Condition Max. Voltage on VDD pin with respect to VDD ground (VSS) -0.5 6.5 V Voltage on any pin with respect to VIN ground (VSS) -0.5 6.5 V Junction temperature -40 Magnetic field induction Storage temperature TJ VDD + V 0.5 150 C B TST Max 40 h/Lifetime -40 150 C For 1000 h, not additive 200 mT Max. 5 min @ TA = 25C 150 mT Max. 5 h @ TA = 25C 150 C Without magnetic field Attention: Stresses above the max. values listed here may cause permanent damage to the device. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Maximum ratings are absolute ratings; exceeding only one of these values may cause irreversible damage to the device. 4.2 Operating Range The following operating conditions must not be exceeded in order to ensure correct operation of the TLE5012B. All parameters specified in the following sections refer to these operating conditions, unless otherwise noted. Table 4-2 is valid for -40C < TJ < 150C unless otherwise noted. Table 4-2 Operating range and parameters Parameter Symbol Values Min. Supply voltage VDD Supply current IDD Magnetic induction at TJ = 25C2)3) BXY Typ. 3.0 Unit Note / Test Condition Max. 5.0 5.5 V 14 16 mA 30 50 mT -40C < TJ < 150C 30 60 mT -40C < TJ < 100C 30 70 mT -40C < TJ < 85C 30 mT Additional angle error of 0.1 Extended magnetic induction range at TJ = 25C2)3) BXY 25 Angle range Ang 0 360 POR level VPOR 2.0 2.9 V POR hysteresis VPORhy Data Sheet 1) 30 19 Power-on reset mV Rev. 2.0, 2014-02 TLE5012B Specification Table 4-2 Operating range (cont'd)and parameters Parameter Symbol Values Min. 4) Power-on time 5) Fast Reset time Typ. tPon Max. 5 tRfast Unit Note / Test Condition 7 ms 0.5 ms VDD > VDDmin; Fast reset is triggered by disabling startup BIST (S_BIST = 0), then enabling chip reset (AS_RST = 1) 1) 2) 3) 4) Directly blocked with 100-nF ceramic capacitor Values refer to a homogeneous magnetic field (BXY) without vertical magnetic induction (BZ = 0mT). See Figure 4-1 During "Power-on time," write access is not permitted (except for the switch to External Clock which requires a readout as a confirmation that external clock is selected) 5) Not subject to production test - verified by design/characterization The field strength of a magnet can be selected within the colored area of Figure 4-1. By limitation of the junction temperature, a higher magnetic field can be applied. In case of a maximum temperature TJ=100C, a magnet with up to 60mT at TJ = 25C is allowed. It is also possible to widen the magnetic field range for higher temperatures. In that case, additional angle errors have to be considered. Figure 4-1 Allowed magnetic field range as function of junction temperature. Data Sheet 20 Rev. 2.0, 2014-02 TLE5012B Specification 4.3 Characteristics 4.3.1 Input/Output characteristics The indicated parameters apply to the full operating range, unless otherwise specified. The typical values correspond to a supply voltage VDD = 5.0 V and 25 C, unless individually specified. All other values correspond to -40 C < TJ < 150C. Within the register MOD_3, the driver strength and the slope for push-pull communication can be varied depending on the sensor output. The driver strength is specified in Table 4-3 and the slope fall and rise time in Table 4-4. Table 4-3 Input voltage and output currents Parameter Symbol Values Min. Input voltage VIN Typ. Unit Note / Test Condition Max. -0.3 5.5 V VDD+ 0.3 V Output current (DATA-Pad) IQ Output current (IFA / IFB / IFC - IQ Pad) -25 mA PAD_DRV ='0x', sink current1)2) -5 mA PAD_DRV ='10', sink current1)2) -0.4 mA PAD_DRV ='11', sink current1)2) -15 mA PAD_DRV ='0x', sink current1)2) -5 mA PAD_DRV ='1x', sink current1)2) 1) Max. current to GND over open-drain output 2) At VDD = 5 V Table 4-4 Driver strength characteristic Parameter Symbol Values Min. Output rise/fall time Typ. tfall, trise Unit Note / Test Condition Max. 8 ns DATA, 50 pF, PAD_DRV='00'1)2) 28 ns DATA, 50 pF, PAD_DRV='01'1)2) 45 ns DATA, 50 pF, PAD_DRV='10'1)2) 130 ns DATA, 50 pF, PAD_DRV='11'1)2) 15 ns IFA/IFB, 20 pF, PAD_DRV='0x'1)2) 30 ns IFA/IFB, 20 pF, PAD_DRV='1x'1)2) 1) Valid for push-pull output 2) Not subject to production test - verified by design/characterization Data Sheet 21 Rev. 2.0, 2014-02 TLE5012B Specification Table 4-5 Electrical parameters for 4.5 V < VDD < 5.5 V Parameter Symbol Values Min. Input signal low-level VL5 Input signal high level VH5 Output signal low-level VOL5 Pull-up current1) Pull-down current Note / Test Condition Max. 0.3 VDD V 0.7 VDD IPU 2) Typ. Unit IPD V 1 V DATA; IQ = -25 mA (PAD_DRV='0x'), IQ = -5 mA (PAD_DRV='10'), IQ = -0.4 mA (PAD_DRV='11') 1 V IFA,B,C; IQ = -15 mA (PAD_DRV='0x'), IQ = -5 mA (PAD_DRV='1x') -10 -225 A CSQ -10 -150 A DATA 10 225 A SCK 10 150 A IFA, IFB, IFC 1) Internal pull-ups on CSQ and DATA pin are always enabled. 2) Internal pull-downs on IFA, IFB and IFC are enabled during startup and in open-drain mode, internal pull-down on SCK is always enabled. Table 4-6 Electrical parameters for 3.0 V < VDD < 3.6 V Parameter Symbol Values Min. Input signal low-level VL3 Input signal high level VH3 Output signal low-level VOL3 Pull-up current1) Pull-down current2) IPU IPD Typ. Unit Note / Test Condition Max. 0.3 VDD V 0.7 VDD V 0.9 V DATA; IQ = -15 mA (PAD_DRV='0x'), IQ = -3 mA (PAD_DRV='10'), IQ = -0.24 mA (PAD_DRV='11') 0.9 V IFA,IFB; IQ = - 10 mA (PAD_DRV='0x'), IQ = -3 mA (PAD_DRV='1x') -3 -225 A CSQ -3 -150 A DATA 3 225 A SCK 3 150 A IFA, IFB, IFC 1) Internal pull-ups on CSQ and DATA pin are always enabled. 2) Internal pull-downs on IFA, IFB and IFC are enabled during startup and in open-drain mode, internal pull-down on SCK is always enabled. Data Sheet 22 Rev. 2.0, 2014-02 TLE5012B Specification 4.3.2 ESD Protection Table 4-7 ESD protection Parameter Symbol Values Min. ESD voltage Unit Notes Max. VHBM 4.0 kV Human Body Model1) VSDM 0.5 kV Socketed Device Model2) 1) Human Body Model (HBM) according to: AEC-Q100-002 2) Socketed Device Model (SDM) according to: ESDA/ANSI/ESD SP5.3.2-2008 4.3.3 GMR Parameters All parameters apply over BXY = 30mT and TA = 25C, unless otherwise specified. Table 4-8 Basic GMR parameters Parameter Symbol Values Min. X, Y output range RGADC X, Y amplitude2) AX, AY Typ. 6000 9500 X, Y synchronicity At ambient temperature 20620 digits Operating range 100 OX, OY -2048 0 +2047 digits X, Y orthogonality error -11.25 0 +11.24 X, Y amplitude without magnet X0 , Y 0 X, Y offset 1) 2) 3) 4) k Operating range1) 15781 digits 87.5 4) Note / Test Condition Max. 23230 digits 3922 3) Unit 112.49 % +4096 digits Operating range1) Not subject to production test - verified by design/characterization See Figure 4-2 k = 100*(AX/AY) OY=(YMAX + YMIN) / 2; OX = (XMAX + XMIN) / 2 VY +A 0 Offset 0 90 180 270 360 Angle -A Figure 4-2 Offset and amplitude definition Data Sheet 23 Rev. 2.0, 2014-02 TLE5012B Specification 4.3.4 Angle Performance After internal calculation, the sensor has a remaining error, as shown in Table 4-9. The error value refers to BZ= 0mT and the operating conditions given in Table 4-2 "Operating range and parameters" on Page 19. The overall angle error represents the relative angle error. This error describes the deviation from the reference line after zero-angle definition. It is valid for a static magnetic field. If the magnetic field is rotating during the measurement, an additional propagation error is caused by the angle delay time (see Table 4-10 "Signal processing" on Page 27), which the sensor needs to calculate the angle from the raw sine and cosine values from the MR bridges. In fast-turning applications, prediction can be enabled to reduce this propagation error. Table 4-9 Angle performance Parameter Symbol Values Min. Overall angle error (with autocalibration) Typ. Err 1) 2) 3) 4) 5) Note / Test Condition Max. 1) 1.0 Including lifetime and temperature drift2)3)4). Note: in case of temperature changes above 5 Kelvin within 1.5 revolutions refer to Figure 4-3 for additional angle error. 0.61) 1.3 Including temperature drift2)3)5) 1.9 Including lifetime and temperature drift2)3)4) 0.6 Overall angle error (without auto- Err calibration) Unit At 25C, B = 30mT Including hysteresis error, caused by revolution direction change Relative error after zero angle definition Not subject to production test - verified by design/characterization 0h If autocalibration (see Chapter 4.3.5) is enabled and the temperature changes by more than 5 Kelvin during 1.5 revolutions an additional error has to be added to the specified angle error in Table 4-9. This error depends on the temperature change (Delta Temperature) as well as from the initial temperature (Tstart) as shown in Figure 4-3. Once the temperature stabilizes and the application completes 1.5 revolutions, then the angle error is as specified in Table 4-9. For negative Delta Temperature changes (from higher to lower temperatures) the additional angle error will be smaller than the corresponding positive Delta Temperature changes (from lower to higher temperatures) shown in Figure 4-3. The Figure 4-3 applies to the worst case. Data Sheet 24 Rev. 2.0, 2014-02 TLE5012B Specification Additional angle error () 3.5 3 2.5 2 Tstart Tstart Tstart Tstart Tstart Tstart Tstart 1.5 1 0.5 0 -40C 25C 85C 105C 125C 135C >135C 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 Delta Temperature (Kelvin) within 1.5 revolutions Figure 4-3 Additional angle error for temperature changes above 5 Kelvin within 1.5 revolutions 4.3.5 Autocalibration The autocalibration enables online parameter calculation and therefore reduces the angle error due to temperature and lifetime drifts. The TLE5012B is a pre-calibrated sensor, so autocalibration is only enabled in some devices by default. The update mode can be chosen with the AUTOCAL setting in the MOD_2 register. The TLE5012B needs 1.5 revolutions to generate new autocalibration parameters. These parameters are continuously updated. The parameters are updated in a smooth way (one Least-Significant Bit within the chosen range or time) to avoid an angle jump on the output. AUTOCAL Modes: * * * * 00: No autocalibration 01: Autocalibration Mode 1. One LSB to final values within the update time tupd (depending on FIR_MD setting). 10: Autocalibration Mode 2. Only one LSB update over one full parameter generation (1.5 revolutions). After update of one LSB, the autocalibration will calculate the parameters again. 11: Autocalibration Mode 3. One LSB to final values within an angle range of 11.25 Data Sheet 25 Rev. 2.0, 2014-02 TLE5012B Specification 4.3.6 Signal Processing TLE5012B X GMR SDADC Filter Angle Calculation Y GMR SDADC Microcontroller IF Filter t delIF t adelSSC t adelIIF Figure 4-4 Signal path The signal path of the TLE5012B is depicted in Figure 4-4. It consists of the GMR-bridge, ADC, filter and angle calculation. The delay time between a physical change in the GMR elements and a signal on the output depends on the filter and interface configurations. In fast turning applications, this delay causes an additional rotation speed dependent angle error. The TLE5012B has an optional prediction feature, which serves to reduce the speed dependent angle error in applications where the rotation speed does not change abruptly. Prediction uses the difference between current and last two angle values to approximate the angle value which will be present after the delay time (see Figure 4-5). The output value is calculated by adding this difference to the measured value, according to Equation (4.1). (t + 1) = (t ) + (t - 1) - (t - 2) (4.1) Sensor output Angle Magnetic field direction tadel t upd With Prediction Without Prediction time Figure 4-5 Delay of sensor output Data Sheet 26 Rev. 2.0, 2014-02 TLE5012B Specification Table 4-10 Signal processing Parameter Symbol Values Min. Filter update period Angle delay time without prediction2) Unit Note / Test Condition 42.7 s FIR_MD = 1 (default)1) 85.3 s FIR_MD = 21) 170.6 s FIR_MD = 31) 85 95 s FIR_MD = 11) 150 165 s FIR_MD = 21) 275 300 s FIR_MD = 31) 120 135 s FIR_MD = 11) 180 200 s FIR_MD = 21) 305 330 s FIR_MD = 31) 45 50 s FIR_MD = 1; PREDICT = 11) 65 70 s FIR_MD = 2; PREDICT = 11) 105 115 s Typ. tupd tadelSSC tadelIIF Angle delay time with prediction2) tadelSSC Max. FIR_MD = 3; PREDICT = 1 1) tadelIIF 75 90 s FIR_MD = 1; PREDICT = 11) 95 110 s FIR_MD = 2; PREDICT = 11) 135 150 s FIR_MD = 3; PREDICT = 1 1) Angle noise (RMS) NAngle 0.08 FIR_MD = 11) 0.05 FIR_MD = 21)(default) 0.04 FIR_MD = 31) 1) Not subject to production test - verified by design/characterization 2) Valid at constant rotation speed All delay times specified in Table 4-10 are valid for an ideal internal oscillator frequency of 24 MHz. For the exact timing, the variation of the internal oscillator frequency has to be taken into account (see Chapter 4.3.7) Data Sheet 27 Rev. 2.0, 2014-02 TLE5012B Specification 4.3.7 Clock Supply (CLK Timing Definition) The internal clock supply of the TLE5012B is subject to production-specific variations, which have to be considered for all timing specifications. Table 4-11 Internal clock timing specification Parameter Symbol Values Min. Typ. Unit Note / Test Condition Max. Digital clock fDIG 22.8 24 25.8 MHz Internal oscillator frequency fCLK 3.8 4.0 4.3 MHz In order to fix the IC timing and synchronize the TLE5012B with other ICs in a system, it can be switched to operate with an external clock signal supplied to the IFC pin. The clock input signal must fulfill certain requirements: * * * The high or low pulse width must not exceed the specified values, because the PLL needs a minimum pulse width and must be spike-filtered. The duty cycle factor should typically be 50%, but it can vary between 30% and 70%. The PLL is triggered at the positive edge of the clock. If more than 2 edges are missing, a chip reset is generated automatically and the sensor restarts with the internal clock. This is indicated by the S_RST, and CLK_SEL bits, and additionally by the Safety Word (see Chapter 4.4.1.2). tCLK tCLKh tCLKl VH VL t Figure 4-6 External CLK timing definition Table 4-12 External Clock Specification Parameter Symbol Values Min. Input frequency CLK duty cycle 1)2) Typ. Unit Note / Test Condition Max. fCLK 3.8 4.0 4.3 MHz CLKDUTY 30 50 70 % CLK rise time tCLKr 30 ns From VL to VH CLK fall time tCLKf 30 ns From VH to VL 1) Minimum duty cycle factor: tCLKh(min) / tCLK with tCLK= 1 / fCLK 2) Maximum duty cycle factor: tCLKh(max) / tCLK with tCLK= 1 / fCLK Data Sheet 28 Rev. 2.0, 2014-02 TLE5012B Specification 4.4 Interfaces 4.4.1 Synchronous Serial Communication (SSC) The 3-pin SSC interface consists of a bi-directional push-pull (tri-state on receive) or open-drain data pin (configurable with SSC_OD bit) and the serial clock and chip-select input pins. The SSC Interface is designed to communicate with a microcontroller peer-to-peer for fast applications. 4.4.1.1 SSC Timing Definition tCSs tCSh tSCKp tCSoff CSQ tSCKh tSCKl SCK DATA tDATAs tDATAh Figure 4-7 SSC timing SSC Inactive Time (CSoff) The SSC inactive time defines the delay time after a transfer before the TLE5012B can be selected again. Table 4-13 SSC push-pull timing specification Parameter Symbol Values Min. Typ. Unit Note / Test Condition Mbit/s 1) Max. SSC baud rate fSSC CSQ setup time tCSs 105 ns 1) CSQ hold time tCSh 105 ns 1) CSQ off tCSoff 600 ns SSC inactive time1) SCK period tSCKp 120 ns 1) SCK high tSCKh 40 ns 1) SCK low tSCKl 30 ns 1) DATA setup time tDATAs 25 ns 1) DATA hold time tDATAh 40 ns 1) Write read delay twr_delay 130 ns 1) Update time tCSupdate 1 s See Figure 4-111) SCK off tSCKoff 170 ns 1) 8.0 125 1) Not subject to production test - verified by design/characterization Data Sheet 29 Rev. 2.0, 2014-02 TLE5012B Specification Table 4-14 SSC open-drain timing specification Parameter Symbol Values Min. Typ. Unit Note / Test Condition Mbit/s Pull-up Resistor = 1k1) Max. SSC baud rate fSSC CSQ setup time tCSs 300 ns 1) CSQ hold time tCSh 400 ns 1) CSQ off tCSoff 600 ns SSC inactive time1) SCK period tSCKp 500 ns 1) SCK high tSCKh 190 ns 1) SCK low tSCKl 190 ns 1) DATA setup time tDATAs 25 ns 1) DATA hold time tDATAh 40 ns 1) Write read delay twr_delay 130 ns 1) Update time tCSupdate 1 s See Figure 4-111) SCK off tSCKoff 170 ns 1) 2.0 1) Not subject to production test - verified by design/characterization Data Sheet 30 Rev. 2.0, 2014-02 TLE5012B Specification 4.4.1.2 SSC Data Transfer The SSC data transfer is word-aligned. The following transfer words are possible: * * * Command Word (to access and change operating modes of the TLE5012B) Data words (any data transferred in any direction) Safety Word (confirms the data transfer and provides status information) twr_delay COMMAND READ Data 1 READ Data 2 SAFETY-WORD SSC-Master is driving DATA SSC-Slave is driving DAT A Figure 4-8 SSC data transfer (data-read example) twr_delay COMMAND WRITE Data 1 SAFETY-WORD SSC-Master is driving DATA SSC-Slave is driving DAT A Figure 4-9 SSC data transfer (data-write example) Command Word SSC Communication between the TLE5012B and a microcontroller is generally initiated by a command word. The structure of the command word is shown in Table 4-15. If an update is triggered by shortly pulling low CSQ without a clock on SCK a snapshot of all system values is stored in the update registers simultaneously. A read command with the UPD bit set then allows to readout this consistent set of values instead of the current values. Bits with an update buffer are marked by an "u" in the Type column in register descriptions. The initialization of such an update is described on page 33. Table 4-15 Structure of the Command Word Name Bits Description RW [15] Read - Write 0: Write 1: Read Lock [14..11] 4-bit Lock Value 0000B: Default operating access for addresses 0x00:0x04 1010B: Configuration access for addresses 0x05:0x11 Data Sheet 31 Rev. 2.0, 2014-02 TLE5012B Specification Table 4-15 Structure of the Command Word (cont'd) Name Bits Description UPD [10] Update-Register Access 0: Access to current values 1: Access to values in update buffer ADDR [9..4] 6-bit Address ND [3..0] 4-bit Number of Data Words Safety Word The safety word consists of the following bits: Table 4-16 Structure of the Safety Word Name 1) STAT Bits Description Chip and Interface Status [15] Indication of chip reset or watchdog overflow (resets after readout) via SSC 0: Reset occurred 1: No reset [14] System error (e.g. overvoltage; undervoltage; VDD-, GND- off; ROM;...) 0: Error occurred (S_VR; S_DSPU; S_OV; S_XYOL: S_MAGOL; S_FUSE; S_ROM; S_ADCT) 1: No error [13] Interface access error (access to wrong address; wrong lock) 0: Error occurred 1: No error [12] Valid angle value (NO_GMR_A = 0; NO_GMR_XY = 0) 0: Angle value invalid 1: Angle value valid RESP [11..8] Sensor number response indicator The sensor number bit is pulled low and the other bits are high CRC [7..0] Cyclic Redundancy Check (CRC) 1) When an error occurs, the corresponding status bit in the safety word remains "low" until the STAT register (address 00H) is read via SSC interface. Bit Types The types of bits used in the registers are listed here: Table 4-17 Bit Types Abbreviation Function Description r Read Read-only registers w Write Read and write registers u Update Update buffer for this bit is present. If an update is issued and the UpdateRegister Access bit (UPD in Command Word) is set, the immediate values are stored in this update buffer simultaneously. This allows a snapshot of all necessary system parameters at the same time. Data Sheet 32 Rev. 2.0, 2014-02 TLE5012B Specification Data communication via SSC SSC Transfer twr_delay Command Word Data Word (s) SCK DATA MSB 14 13 12 11 10 9 8 7 6 5 4 3 2 1 LSB MSB 1 LSB CSQ RW LOCK UPD ADDR LENGTH SSC -Master is driving DAT A SSC -Slave is driving DAT A Figure 4-10 SSC bit ordering (read example) Update -Signal SCK Command Word Data Word (s) Update -Event MSB DATA LSB LSB CSQ tCSupdate SSC -Master is driving DAT A SSC -Slave is driving DAT A Figure 4-11 Update of update registers The data communication via SSC interface has the following characteristics: * * * * * * * * * * * * The data transmission order is Most-Significant Bit (MSB) first, Last-Significant Bit (LSB) last. Data is put on the data line with the rising edge on SCK and read with the falling edge on SCK. The SSC Interface is word-aligned. All functions are activated after each transmitted word. After every data transfer with ND 1, the 16-bit Safety Word is appended by the TLE5012B. A "high" condition on the Chip Select pin (CSQ) of the selected TLE5012B interrupts the transfer immediately. The CRC calculator is automatically reset. After changing the data direction, a delay twr_delay (see Table 4-14) has to be implemented before continuing the data transfer. This is necessary for internal register access. If in the Command Word the number of data is greater than 1 (ND > 1), then a corresponding number of consecutive registers is read, starting at the address given by ADDR. In case an overflow occurs at address 3FH, the transfer continues at address 00H. If in the Command Word the number of data is zero (ND = 0), the register at the address given by ADDR is read, but no Safety Word is sent by the TLE5012B. This allows a fast readout of one register. At a rising edge of CSQ without a preceding data transfer (no SCK pulse, see Figure 4-11), the content of all registers which have an update buffer is saved into the buffer. This procedure serves to take a snapshot of all relevant sensor parameters at a given time. The content of the update buffer can then be read by sending a read command for the desired register and setting the UPD bit of the Command Word to "1". After sending the Safety Word, the transfer ends. To start another data transfer, the CSQ has to be deselected once for at least tCSoff. By default, the SSC interface is set to push-pull. The push-pull driver is active only if the TLE5012B has to send data, otherwise the DATA pin is set to high-impedance. Data Sheet 33 Rev. 2.0, 2014-02 TLE5012B Specification Cyclic Redundancy Check (CRC) * * * * * * This CRC is according to the J1850 Bus Specification. Every new transfer restarts the CRC generation. Every Byte of a transfer will be taken into account to generate the CRC (also the sent command(s)). Generator polynomial: X8+X4+X3+X2+1, but for the CRC generation the fast-CRC generation circuit is used (see Figure 4-12) The seed value of the fast CRC circuit is '11111111B'. The remainder is inverted before transmission. Serial CRC output X7 1 X6 1 X5 1 X4 1 xor X3 1 X2 xor 1 X1 xor 1 X0 1 & xor Input TX_CRC parallel Remainder Figure 4-12 Fast CRC polynomial division circuit 4.4.2 Pulse Width Modulation (PWM) Interface The Pulse Width Modulation (PWM) interface can be selected via SSC (IF_MD = `01'). The PWM update rate can be programmed within the register 0EH (IFAB_RES) in the following steps: * * * * ~0.25 kHz with 12-bit resolution ~0.5 kHz with 12-bit resolution ~1.0 kHz with 12-bit resolution ~2.0 kHz with 12-bit resolution PWM uses a square wave with constant frequency whose duty cycle is modulated according to the last measured angle value (AVAL register). Figure 4-13 shows the principal behavior of a PWM with various duty cycles and the definition of timing values. The duty cycle of a PWM is defined by the following general formulas: Duty Cycle = ton t PWM t PWM = t on + toff f PWM = 1 t PWM (4.2) The duty cycle range between 0 - 6.25% and 93.75 - 100% is used only for diagnostic purposes. In case the sensor detects an error, the corresponding error bit in the Status register is set and the PWM duty cycle goes to the lower (0 - 6.25%) or upper (93.75 - 100%) diagnostic range, depending on the kind of error (see "Output duty cycle range" in Table 4-18). Except for an S_ADCT error, an error is only indicated by the corresponding diagnostic duty-cycle as long as it persists, but at least once. However the value in the status register will remain until a readout via the SSC interface or a chip reset is performed. An S_ADCT error on the other side will be transmitted until the next chip reset. This fail-safe diagnostic function can be disabled via the MOD_4 register. Sensors with preset PWM are available as TLE5012B E50x0. Data Sheet 34 Rev. 2.0, 2014-02 TLE5012B Specification ON = High level OFF = Low level UIFA Vdd tON tPWM Duty cycle = 6.25% tOFF 0' UIFA Vdd UIFA 0' Vdd Duty cycle = 50% t Duty cycle = 93.75% t 0' t Figure 4-13 Typical example of a PWM signal Table 4-18 PWM interface Parameter Symbol Values Min. PWM output frequencies (Selectable by IFAB_RES) Output duty cycle range Typ. Unit Note / Test Condition Max. fPWM1 232 244 262 Hz 1) fPWM2 464 488 525 Hz 1) fPWM3 929 977 1050 Hz 1) fPWM4 1855 1953 2099 Hz 1) DYPWM 6.25 93.75 % Absolute angle1) 2 % Electrical Error (S_RST; S_VR)1) 98 % System error (S_FUSE; S_OV; S_XYOL; S_MAGOL; S_ADCT)1) 0 1 % 99 100 % Short to GND1) Short to VDD, power loss1) 1) Not subject to production test - verified by design/characterization The PWM frequency is derived from the digital clock via f PWM = (4.3) f DIG * 2 IFAB_RES 24 * 4096 The min/max values given in Table 4-18 take into account the internal digital clock variation specified in Chapter 4.3.7. If external clock is used, the variation of the PWM frequency can be derived from the variation of the external clock using Equation (4.3). Data Sheet 35 Rev. 2.0, 2014-02 TLE5012B Specification 4.4.3 Short PWM Code (SPC) The Short PWM Code (SPC) is a synchronized data transmission based on the SENT protocol (Single Edge Nibble Transmission) defined by SAE J2716. As opposed to SENT, which implies a continuous transmission of data, the SPC protocol transmits data only after receiving a specific trigger pulse from the microcontroller. The required length of the trigger pulse depends on the sensor number, which is configurable. Thereby, SPC allows the operation of up to four sensors on one bus line. SPC enables the use of enhanced protocol functionality due to the ability to select between various sensor slaves (ID selection). The slave number (S_NR) can be given by the external circuit of SCK and IFC pin. In case of VDD on SCK, the S_NR[0] can be set to 1 and in the case of GND on SCK the S_NR[0] is equal to 0. S_NR[1] can be adjusted in the same way by the IFC pin. As in SENT, the time between two consecutive falling edges defines the value of a 4-bit nibble, thus representing numbers between 0 and 15. The transmission time therefore depends on the transmitted data values. The single edge is defined by a 3 Unit Time (UT, see Chapter 4.4.3.1) low pulse on the output, followed by the high time defined in the protocol (nominal values, may vary depending on the tolerance of the internal oscillator and the influence of external circuitry). All values are multiples of a unit time frame concept. A transfer consists of the following parts (Figure 4-14): * * * * * * A trigger pulse by the master, which initiates the data transmission A synchronization period of 56 UT (in parallel, a new sample is calculated) A status nibble of 12-27 UT Between 3 and 6 data nibbles of 12-27 UT A CRC nibble of 12-27 UT An end pulse to terminate the SPC transmission Trigger Nibble Synchronisation Frame Status -Nibble Data-Nibble 1 Bit 11-8 Data-Nibble 2 Bit 7-4 Data-Nibble 3 Bit 3-0 56 tck 12..27 tck 12..27 tck 12..27 tck 12..27 tck 24,34,51,78 tck C Activity Sensor Activity CRC End -Pulse 12..27 tck 12 tck Time-Base: 1 tck (3s+/-dtck ) Nibble-Encoding : ( 12+x)*tck Figure 4-14 SPC frame example The CRC checksum includes the status nibble and the data nibbles, and can be used to check the validity of the decoded data. The sensor is available for the next trigger pulse 90s after the falling edge of the end pulse (see Figure 4-15). Trigger Nibble Synchronisation Frame End-Pulse Trigger Nibble ... C Activity Sensor Activity Synchronisation Frame End-Pulse ... > 90 s Figure 4-15 SPC pause timing diagram In SPC mode, the sensor does not continuously calculate an angle from the raw data. Instead, the angle calculation is started by the trigger nibble from the master. In this mode, the AVAL register, which stores the angle value and can be read via SSC, contains the angle which was calculated after the last SPC trigger nibble. Data Sheet 36 Rev. 2.0, 2014-02 TLE5012B Specification In parallel to SPC, the SSC interface can be used for individual configuration. The number of transmitted SPC nibbles can be changed to customize the amount of information sent by the sensor. The frame contains a 16-bit angle value and an 8-bit temperature value in the full configuration (Table 4-19). Sensors with preset SPC are available as TLE5012B E9000 Table 4-19 Frame configuration Frame type IFAB_RES Data nibbles 12-bit angle 00 3 nibbles 16-bit angle 01 4 nibbles 12-bit angle, 8-bit temperature 10 5 nibbles 16-bit angle, 8-bit temperature 11 6 nibbles The status nibble, which is sent with each SPC data frame, provides an error indication similar to the Safety Word of the SSC protocol. In case the sensor detects an error, the corresponding error bit in the Status register is set and either the bit SYS_ERR or the bit ELEC_ERR of the status nibble will be "high", depending on the kind of error (see Table 4-20). Except for an S_ADCT error, an error is only indicated by the corresponding error bit in the status nibble as long as it persists, but at least once. However the value in the status register will remain until a read-out via the SSC interface or a chip reset is performed. An S_ADCT error on the other side will be transmitted until the next chip reset. The fail-safe diagnostic function can be disabled via the MOD_4 register. Table 4-20 Structure of status nibble Name Bits Description SYS_ERR [3] Indication of system error (S_FUSE, S_OV, S_XYOL, S_MAGOL, S_ADCT) 0: No system error 1: System error occurred ELEC_ERR [2] Indication of electrical error (S_RST, S_VR) 0: No electrical error 1: Electrical error occurred S_NR [1] Slave number bit 1 (level on IFC) [0] Slave number bit 0 (level on SCK) 4.4.3.1 Unit Time Setup The basic SPC protocol unit time granularity is defined as 3 s. Every timing is a multiple of this basic time unit.To achieve more flexibility, trimming of the unit time can be done within IFAB_HYST. This enables a setup of different unit times. Table 4-21 Predivider setting Parameter Symbol Values Min. Unit time Typ. tUnit 3.0 Unit Note / Test Condition s IFAB_HYST = 001) Max. 2.5 IFAB_HYST = 011) 2.0 IFAB_HYST = 101) 1.5 IFAB_HYST = 111) 1) Not subject to production test - verified by design/characterization Data Sheet 37 Rev. 2.0, 2014-02 TLE5012B Specification 4.4.3.2 Master Trigger Pulse Requirements An SPC transmission is initiated by a master trigger pulse on the IFA pin. To detect a low-level on the IFA pin, the voltage must be below a threshold Vth. The sensor detects that the IFA line has been released as soon as Vth is crossed. Figure 4-16 shows the timing definitions for the master pulse. The master low time tmlow as well as the total trigger time tmtr are given in Table 4-22. If the master low time exceeds the maximum low time, the sensor does not respond and is available for a next triggering 30 s after the master pulse crosses Vthr. tmd,tot is the delay between internal triggering of the falling edge in the sensor and the triggering of the ECU. tmtr SPC ECU trigger level Vth t md,tot tmlow Figure 4-16 SPC Master pulse timing Table 4-22 Master pulse parameters Parameter Symbol Values Unit Note / Test Condition 50 % of VDD 1) 8 % of VDD = 5 V1) 3 VDD VDD = 3 V1) 90 UT SPC_Trigger = 0;1)2) tmlow +12 UT SP_Trigger = 11) 8 12 14 UT S_NR =001) 16 22 27 S_NR =011) 29 39 48 S_NR =101) 50 66 81 S_NR =111) Min. Threshold Vth Threshold hysteresis Vthhyst Total trigger time Master low time Master delay time Typ. tmtr tmlow tmd,tot 5.8 Max. s 1) 1) Not subject to production test - verified by design/characterization 2) Trigger time in the sensor is fixed to the number of units specified in the "typ." column, but the effective trigger time varies due to the sensor's clock variation 4.4.3.3 Checksum Nibble Details The checksum nibble is a 4-bit CRC of the data nibbles including the status nibble. The CRC is calculated using a polynomial x4+x3+x2+1 with a seed value of 0101B. The remainder after the last data nibble is transmitted as CRC. Data Sheet 38 Rev. 2.0, 2014-02 TLE5012B Specification 4.4.4 Hall Switch Mode (HSM) The Hall Switch Mode (HSM) within the TLE5012B makes it possible to emulate the output of 3 Hall switches. Hall switches are often used in electrical commutated motors to determine the rotor position. With these 3 output signals, the motor will be commutated in the right way. Depending on which pole pairs of the rotor are used, various electrical periods have to be controlled. This is selectable within 0EH (HSM_PLP). Figure 4-17 depicts the three output signals with the relationship between electrical angle and mechanical angle. The mechanical 0 point is always used as reference. The HSM is generally used with push-pull output, but it can be changed to open-drain within the register IFAB_OD. Sensors with preset HSM are available as TLE5012B E3005. Hall-Switch-Mode: 3phase Generation Electrical Angle 0 60 120 180 240 300 360 HS1 HS2 HS3 Angle Mech. Angle with 5 Pole Pairs 0 12 24 36 48 60 72 Mech. Angle with 3 Pole Pairs 0 20 40 60 80 100 120 Figure 4-17 Hall Switch Mode The HSM Interface can be selected via SSC (IF_MD = 010). Table 4-23 Hall Switch Mode Parameter Symbol Values Min. Rotation speed Data Sheet Typ. n Unit Max. 10000 rpm 39 Note / Test Condition Mechanical2) Rev. 2.0, 2014-02 TLE5012B Specification Table 4-23 Hall Switch Mode (cont'd) Parameter Symbol Values Min. Electrical angle accuracy Mechanical angle switching hysteresis Data Sheet Typ. elect HShystm 0 Unit Max. 0.6 1 1 pole pair with autocalibration1)2) 1.2 2 2 pole pairs with autocal.1)2) 1.8 3 3 pole pairs with autocal.1)2) 2.4 4 4 pole pairs with autocal.1)2) 3.0 5 5 pole pairs with autocal.1)2) 3.6 6 6 pole pairs with autocal.1)2) 4.2 7 7 pole pairs with autocal.1)2) 4.8 8 8 pole pairs with autocal.1)2) 5.4 9 9 pole pairs with autocal.1)2) 6.0 10 10 pole pairs with autocal.1)2) 6.6 11 11 pole pairs with autocal.1)2) 7.2 12 12 pole pairs with autocal.1)2) 7.8 13 13 pole pairs with autocal.1)2) 8.4 14 14 pole pairs with autocal.1)2) 9.0 15 15 pole pairs with autocal.1)2) 9.6 16 16 pole pairs with autocal.1)2) 0.703 40 Note / Test Condition Selectable by IFAB_HYST2)3)4) Rev. 2.0, 2014-02 TLE5012B Specification Table 4-23 Hall Switch Mode (cont'd) Parameter Symbol Values Min. Electrical angle switching hysteresis5) Unit Note / Test Condition 0.70 1 pole pair; IFAB_HYST=111)2) 1.41 2 pole pairs; IFAB_HYST=111)2) 2.11 3 pole pairs; IFAB_HYST=111)2) 2.81 4 pole pairs; IFAB_HYST=111)2) 3.52 5 pole pairs; IFAB_HYST=111)2) 4.22 6 pole pairs; IFAB_HYST=111)2) 4.92 7 pole pairs; IFAB_HYST=111)2) 5.62 8 pole pairs; IFAB_HYST=111)2) 6.33 9 pole pairs; IFAB_HYST=111)2) 7.03 10 pole pairs; IFAB_HYST=111)2) 7.73 11 pole pairs; IFAB_HYST=111)2) 8.44 12 pole pairs; IFAB_HYST=111)2) 9.14 13 pole pairs; IFAB_HYST=111)2) 9.84 14 pole pairs; IFAB_HYST=111)2) 10.55 15 pole pairs; IFAB_HYST=111)2) 11.25 16 pole pairs; IFAB_HYST=111)2) Typ. HShystel Max. Fall time tHSfall 0.02 1 s RL = 2.2k; CL < 50pF2) Rise time tHSrise 0.4 1 s RL = 2.2k; CL < 50pF2) 1) 2) 3) 4) 5) Depends on internal oscillator frequency variation (Section 4.3.7) Not subject to production test - verified by design/characterization GMR hysteresis not considered Minimum hysteresis without switching The hysteresis has to be considered only at change of rotation direction To avoid switching due to mechanical vibrations of the rotor, an artificial hysteresis is recommended (Figure 4-18). Data Sheet 41 Rev. 2.0, 2014-02 TLE5012B Specification Ideal Switching Point HShystel HShystel elect elect 0 Figure 4-18 HS hysteresis 4.4.5 Incremental Interface (IIF) The Incremental Interface (IIF) emulates the operation of an optical quadrature encoder with a 50% duty cycle. It transmits a square pulse per angle step, where the width of the steps can be configured from 9bit (512 steps per full rotation) to 12bit (4096 steps per full rotation) within the register MOD_4 (IFAB_RES). The rotation direction is given either by the phase shift between the two channels IFA and IFB (A/B mode) or by the level of the IFB channel (Step/Direction mode), as shown in Figure 4-19 and Figure 4-20. The incremental interface can be configured for A/B mode or Step/Direction mode in register MOD_1 (IIF_MOD). Using the Incremental Interface requires an up/down counter on the microcontroller, which counts the pulses and thus keeps track of the absolute position. The counter can be synchronized periodically by using the SSC interface in parallel. The angle value (AVAL register) read out by the SSC interface can be compared to the stored counter value. In case of a non-synchronization, the microcontroller adds the difference to the actual counter value to synchronize the TLE5012B with the microcontroller. After startup, the IIF transmits a number of pulses which correspond to the actual absolute angle value. Thus, the microcontroller gets the information about the absolute position. The Index Signal that indicates the zero crossing is available on the IFC pin. Sensors with preset IIF are available as TLE5012B E1000. A/B Mode The phase shift between phases A and B indicates either a clockwise (A follows B) or a counterclockwise (B follows A) rotation of the magnet. Incremental Interface (A/B Mode) 90 el . Phase shift Phase A V H VL Phase B V H VL Counter 0 1 2 3 4 5 6 7 6 5 4 3 2 1 Figure 4-19 Incremental interface with A/B mode Data Sheet 42 Rev. 2.0, 2014-02 TLE5012B Specification Step/Direction Mode Phase A pulses out the increments and phase B indicates the direction. Incremental Interface (Step /Direction Mode) VH VL Step Direction VH VL Counter 0 1 2 3 4 5 6 7 6 5 4 3 2 1 Figure 4-20 Incremental interface with Step/Direction mode Table 4-24 Incremental Interface Parameter Symbol Values Min. Incremental output frequency fInc Index pulse width t0 Typ. Unit Note / Test Condition Max. 1.0 MHz s 5 Frequency of phase A and phase B1) 01) 1) Not subject to production test - verified by design/characterization 4.5 Test Mechanisms 4.5.1 ADC Test Vectors In order to test the correct functionality of the ADCs, the ADC inputs can be switched from the GMR bridge outputs to a chain of fixed resitors which act as a voltage divider. The ADCs are then fed with test vectors of fixed voltages to simulate a set of magnet positions. The functionality of the ADCs is verified by checking the angle value (AVAL register) for each test vector. This test is activated via SSC command within the SIL register (ADCTV_EN). Registers ADCTV_Y and ADCTV_X are used to select the test vector, as shown in Figure 4-21. The following X/Y ADC values can be programmed: * * * * 4 points, circle amplitude = 70% (0,90, 180, 270) 8 points, circle amplitude = 100% (0, 45, 90, 135, 180, 225, 270, 315) 8 points, circle amplitude = 122.1% (35.3, 54.7, 125.3, 144.7, 215.3, 234.7, 305.3, 324.7) 4 points, circle amplitude = 141.4% (45, 135, 225, 315) Note: The 100% values typically correspond to 21700 digits and the 70% values to 15500 digits. Table 4-25 ADC test vectors Register bits X/Y values (decimal) Min. Typ. 000 0 001 15500 010 21700 011 32767 1) 100 0 101 -15500 Data Sheet 43 Max. Rev. 2.0, 2014-02 TLE5012B Specification Table 4-25 ADC test vectors (cont'd) Register bits X/Y values (decimal) Min. Typ. 110 -21700 111 -32768 Max. 1) Not allowed to use ADCTV_Y 122.1% 141.4% 100 .0% 0% ADCTV_X 70% Figure 4-21 ADC test vectors 4.6 Supply Monitoring The internal voltage nodes of the TLE5012B are monitored by a set of comparators in order to ensure error-free operation. An over- or undervoltage condition must be active at least 256 periods of the digital clock to set the corresponding error bits in the Status register. This works as digital spike suppression. Over- or undervoltage errors trigger the S_VR bit of Status register. This error condition is signaled via the in the Safety Word of the SSC protocol, the status nibble of the SPC interface or the lower diagnostic range of the PWM interface. Table 4-26 Test comparator threshold voltages Parameter Symbol Values Min. Typ. Unit Note / Test Condition Max. VOVG 2.80 V 1) VOVA 2.80 V 1) VOVD 2.80 V 1) VDD overvoltage VDDOV 6.05 V 1) VDD undervoltage VDDUV 2.70 V 1) GND - off voltage VGNDoff -0.55 V 1) VDD - off voltage VVDDoff 0.55 V 1) Spike filter delay tDEL s 1) Overvoltage detection 10 1) Not subject to production test - verified by design/characterization Data Sheet 44 Rev. 2.0, 2014-02 TLE5012B Specification 4.6.1 Internal Supply Voltage Comparators Every voltage regulator has an overvoltage (OV) comparator to detect malfunctions. If the nominal output voltage of 2.5 V is larger than VOVG, VOVA and VOVD, then this overvoltage comparator is activated. 4.6.2 VDD Overvoltage Detection The overvoltage detection comparator monitors the external supply voltage at the VDD pin. VDDA - REF VDD VRG VRA VRD 10s Spike Filter + GND xxx_OV GND Figure 4-22 Overvoltage comparator 4.6.3 GND - Off Comparator The GND - Off comparator is used to detect a voltage difference between the GND pin and SCK. This circuit can detect a disconnection of the supply GND Pin. VDD VDDA Diodereference SCK +dV - 1s Mono Flop + GND 10s Spike Filter GND_OFF GND Figure 4-23 GND - off comparator 4.6.4 VDD - Off Comparator The VDD - Off comparator detects a disconnection of the VDD pin supply voltage. In this case, the TLE5012B is supplied by the SCK and CSQ input pins via the ESD structures. VDDA - VDD 1s Mono Flop VVDDoff CSQ SCK -dV GND + 10s Spike Filter VDD _OFF GND Figure 4-24 VDD - off comparator Data Sheet 45 Rev. 2.0, 2014-02 TLE5012B Pre-Configured Derivates 5 Pre-Configured Derivates Derivates of the 5012B are available with different pre-configured register settings for specific applications. The configuration of all derivates can be changed via SSC interface. 5.1 IIF-type: E1000 The TLE5012B-E1000 is preconfigured for Incremental Interface and fast angle update period (42.7 s). It is most suitable for BLDC motor commutation. * * * * * Autocalibration mode 1 enabled. Prediction enabled. Hysteresis is set to 0.703. 12bit mode, one count per 0.088 angle step. Incremental Interface A/B mode. 5.2 HSM-type: E3005 The TLE5012B-E3005 is preconfigured for Hall-Switch-Mode and fast angle update period (42.7 s). It is most suitable as a replacement for three Hall switches for BLDC motor commutation. * * * * Number of pole pairs is set to 5. Autocalibration mode 1 enabled. Prediction enabled. Hysteresis is set to 0.703. 5.3 PWM-type: E5000 The TLE5012B-E5000 is preconfigured for Pulse-Width-Modulation interface. It is most suitable for steering angle and actuator position sensing. * * * Filter update period is 85.4 s. PWM frequency is 244 Hz. Autocalibration, Prediction, and Hysteresis are disabled. 5.4 PWM-type: E5020 The TLE5012B-E5020 is preconfigured for Pulse-Width-Modulation interface with high frequency. It is most suitable for steering angle and actuator position sensing. * * * * * Filter update period is 42.7 s. PWM frequency is 1953 Hz. Autocalibration mode 2 enabled. Prediction and Hysteresis are disabled. PWM interface is set to open-drain output. 5.5 SPC-type: E9000 The TLE5012B-E9000 is preconfigured for Short-PWM-Code interface. It is most suitable for steering angle and actuator position sensing. * * * * Filter update period is 85.4 s. Autocalibration, Prediction, and Hysteresis are disabled. SPC unit time is 3 s. SPC interface is set to open-drain output. Data Sheet 46 Rev. 2.0, 2014-02 TLE5012B Package Information 6 Package Information 6.1 Package Parameters Table 6-1 Package Parameters Parameter Symbol Limit Values Min. Thermal resistance Unit Notes Typ. Max. 200 K/W Junction to air1) RthJC 75 K/W Junction to case RthJL 85 K/W Junction to lead RthJA Soldering moisture level Lead Frame 150 MSL 3 260C Cu Plating Sn 100% > 7 m 1) according to Jedec JESD51-7 6.2 Package Outline Figure 6-1 PG-DSO-8 package dimension Data Sheet 47 Rev. 2.0, 2014-02 TLE5012B Package Information Figure 6-2 Position of sensing element Table 6-2 Sensor IC placement tolerances in package Parameter Values Min. position eccentricity Unit Max. -200 200 m rotation -3 3 tilt -3 3 in X- and Y-direction affects zero position offset of sensor Footprint 1.31 6.3 Notes 5.69 0.65 1.27 Figure 6-3 Footprint of PG-DSO-8 Data Sheet 48 Rev. 2.0, 2014-02 TLE5012B Package Information 6.4 Packing 0.3 5.2 12 0.3 8 1.75 6.4 2.1 Figure 6-4 Tape and Reel 6.5 Marking Position Marking Description 1st Line 012Bxxxx See ordering table on Page 8 2nd Line xxx Lot code 3rd Line Gxxxx G..green, 4-digit..date code Processing Note: For processing recommendations, please refer to Infineon's Notes on processing Data Sheet 49 Rev. 2.0, 2014-02 w w w . i n f i n e o n . c o m Published by Infineon Technologies AG Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Infineon: TLE5012BE5020XUMA1 TLE5012B E5000 TLE5012B E9000 TLE5012BE1000XUMA1 TLE5012BE3005XUMA1 TLE5012BE5000FUMA1 TLE5012BE9000FUMA1