April 2010 Doc ID 13834 Rev 5 1/17
17
STD95N2LH5
STP95N2LH5, STU95N2LH5
N-channel 25 V, 0.0038 Ω, 80 A, DPAK, IPAK, TO-220
STripFET™ V Power MOSFET
Features
■RDS(on) * Qg industry benchmark
■Extremely low on-resistance RDS(on)
■High avalanche ruggedness
■Low gate drive power losses
Application
■Switching applications
Description
This STripFET™V Power MOSFET technology is
among the latest improvements, which have been
especially tailored to achieve very low on-state
resistance providing also one of the best-in-class
FOM (figure of merit).
Figure 1. Internal schematic diagram
Type VDSS RDS(on) max ID
STD95N2LH5 25 V < 0.0045 Ω80 A
STP95N2LH5 25 V < 0.0049 Ω80 A
STU95N2LH5 25 V < 0.0049 Ω80 A
DPAK
1
3
3
2
1
IPAK
123
TO-220
!-V
$4!"OR
'
3
Table 1. Device summary
Order codes Marking Package Packaging
STD95N2LH5 95N2LH5 DPAK Tape and reel
STP95N2LH5 95N2LH5 TO-220 Tube
STU95N2LH5 95N2LH5 IPAK Tube
www.st.com
Contents STD95N2LH5, STP95N2LH5, STU95N2LH5
2/17 Doc ID 13834 Rev 5
Contents
1 Electrical ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1 Electrical characteristics (curves) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3 Test circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5 Packaging mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
6 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
STD95N2LH5, STP95N2LH5, STU95N2LH5 Electrical ratings
Doc ID 13834 Rev 5 3/17
1 Electrical ratings
Table 2. Absolute maximum ratings
Symbol Parameter
Value
Unit
DPAK/IPAK TO-220
VDS Drain-source voltage (VGS=0) 25 V
VGS Gate-Source voltage ± 22 V
ID (1)
1. Limited by wire bonding
Drain current (continuous) at TC = 25°C 80 95 A
ID Drain current (continuous) at TC = 100°C 67 A
IDM (2)
2. Pulse width limited by safe operating area
Drain current (pulsed) 320 380 A
PTOT Total dissipation at TC = 25°C 70 80 W
Derating factor 0.47 W/°C
EAS (3)
3. Starting Tj = 25°C, Id = 40 A, Vdd = 20 V
Single pulse avalanche energy 165 mJ
Tj
Tstg
Operating junction temperature
Storage temperature -55 to 175 °C
Table 3. Thermal resistance
Symbol Parameter Value Unit
Rthj-case Thermal resistance junction-case max 2.14 °C/W
Rthj-amb Thermal resistance junction-case max 100 °C/W
TjMaximum lead temperature for soldering purpose 275 °C
Electrical characteristics STD95N2LH5, STP95N2LH5, STU95N2LH5
4/17 Doc ID 13834 Rev 5
2 Electrical characteristics
(TCASE=25 °C unless otherwise specified)
Table 4. Static
Symbol Parameter Test conditions Min. Typ. Max. Unit
V(BR)DSS
Drain-source breakdown
Voltage ID = 250 µA, VGS= 0 25 V
IDSS
Zero gate voltage drain
current (VGS = 0)
VDS = 25 V
VDS = 25 V,Tc = 125°C
1
10
µA
µA
IGSS
Gate body leakage current
(VDS = 0) VGS = ± 22 V ±100 nA
VGS(th) Gate threshold voltage VDS= VGS, ID = 250 µA 1 V
RDS(on)
Static drain-source on
resistance
VGS= 10 V, ID= 40 A
SMD version 0.0038 0.0045 Ω
VGS= 10 V, ID= 40 A 0.0044 0.0049 Ω
VGS= 5 V, ID= 40 A
SMD version 0.005 0.006 Ω
VGS= 5 V, ID= 40 A 0.006 0.007 Ω
Table 5. Dynamic
Symbol Parameter Test conditions Min. Typ. Max. Unit
Ciss
Coss
Crss
Input capacitance
Output capacitance
Reverse transfer
capacitance
VDS =25 V, f=1 MHz,
VGS=0 -
1817
420
67
-
pF
pF
pF
Qg
Qgs
Qgd
Total gate charge
Gate-source charge
Gate-drain charge
VDD=13 V, ID = 80 A
VGS =5 V
Figure 18
-
13.4
6.7
4.1
-
nC
nC
nC
Qgs1
Qgs2
Pre Vth gate-to-source
charge
Post Vth gate-to-source
charge
VDD=13 V, ID = 80 A
Figure 21 -
3.5
3.2
-
nC
nC
RGGate input resistance
f=1 MHz gate bias
Bias= 0 test signal
level=20 mV
open drain
-1.1-Ω
STD95N2LH5, STP95N2LH5, STU95N2LH5 Electrical characteristics
Doc ID 13834 Rev 5 5/17
Table 6. Switching on/off (inductive load)
Symbol Parameter Test conditions Min. Typ. Max. Unit
td(on)
tr
Turn-on delay time
Rise time
VDD=12.5 V, ID= 40 A,
RG= 4.7 Ω, VGS= 10 V
Figure 17
-7
38 -ns
ns
td(off)
tf
Turn-off delay time
Fall time
VDD=12.5 V, ID= 40 A,
RG= 4.7 Ω, VGS= 10 V
Figure 17
-22
7-ns
ns
Table 7. Source drain diode
Symbol Parameter Test conditions Min. Typ. Max. Unit
ISD
ISDM(1)
1. Pulse width limited by safe operating area
Source-drain current
Source-drain current (pulsed) -80
320
A
A
VSD(2)
2. Pulsed: pulse duration = 300 µs, duty cycle 1.5%
Forward on voltage ISD= 35 A, VGS=0 - 1.1 V
trr
Qrr
IRRM
Reverse recovery time
Reverse recovery charge
Reverse recovery current
ISD = 80 A, VDD= 20 V
di/dt =100 A/µs,
Figure 19
-
32.4
27.1
1.7
ns
nC
A
Electrical characteristics STD95N2LH5, STP95N2LH5, STU95N2LH5
6/17 Doc ID 13834 Rev 5
2.1 Electrical characteristics (curves)
Figure 2. Safe operating area for DPAK, IPAK Figure 3. Thermal impedance for DPAK, IPAK
Figure 4. Safe operating area for TO-220 Figure 5. Thermal impedance for TO-220
Figure 6. Output characteristics Figure 7. Transfer characteristics
ID
100
10
1
0.1
0.1 1100 VDS(V)
10
(A)
Operation in this area is
Limited by max R
DS(on)
100µs
1ms
Tj=150°C
Tc=25°C
Sinlge
pulse
10ms
AM04907v1
STD95N2LH5, STP95N2LH5, STU95N2LH5 Electrical characteristics
Doc ID 13834 Rev 5 7/17
Figure 8. Normalized BVDSS vs temperature Figure 9. Static drain-source on resistance
Figure 10. Gate charge vs gate-source voltage Figure 11. Capacitance variations
Figure 12. Normalized gate threshold voltage
vs temperature
Figure 13. Normalized on resistance vs
temperature
Electrical characteristics STD95N2LH5, STP95N2LH5, STU95N2LH5
8/17 Doc ID 13834 Rev 5
Figure 14. Source-drain diode forward
characteristics
STD95N2LH5, STP95N2LH5, STU95N2LH5 Test circuits
Doc ID 13834 Rev 5 9/17
3 Test circuits
Figure 15. Unclamped inductive load test
circuit
Figure 16. Unclamped inductive waveform
Figure 17. Switching times test circuit for
resistive load
Figure 18. Gate charge test circuit
Figure 19. Test circuit for inductive load
switching and diode recovery times
Figure 20. Switching time waveform
Test circuits STD95N2LH5, STP95N2LH5, STU95N2LH5
10/17 Doc ID 13834 Rev 5
Figure 21. Gate charge waveform
Vds
Vgs
Id
Vgs(th)
Qgs1 Qgs2 Qgd
STD95N2LH5, STP95N2LH5, STU95N2LH5 Package mechanical data
Doc ID 13834 Rev 5 11/17
4 Package mechanical data
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK is an ST trademark.
Package mechanical data STD95N2LH5, STP95N2LH5, STU95N2LH5
12/17 Doc ID 13834 Rev 5
TO-220 type A mechanical data
Dim mm
Min Typ Max
A 4.40 4.60
b0.61 0.88
b1 1.14 1.70
c0.480.70
D 15.25 15.75
D1 1.27
E10 10.40
e 2.40 2.70
e1 4.95 5.15
F1.231.32
H1 6.20 6.60
J1 2.40 2.72
L1314
L1 3.50 3.93
L20 16.40
L3028.90
∅P3.75 3.85
Q 2.65 2.95
0015988_Rev_S
STD95N2LH5, STP95N2LH5, STU95N2LH5 Package mechanical data
Doc ID 13834 Rev 5 13/17
DIM. mm.
min. typ max.
A 2.20 2.40
A1 0.901.10
b0.64 0.90
b20.95
b4 5.20 5.40
c 0.45 0.60
c2 0.480.60
D 6.00 6.20
E 6.40 6.60
e2.28
e1 4.40 4.60
H 16.10
L9.00 9.40
(L1) 0.801.20
L2 0.80
V1 10
o
TO-251 (IPAK) mechanical data
0068771_H
Package mechanical data STD95N2LH5, STP95N2LH5, STU95N2LH5
14/17 Doc ID 13834 Rev 5
DIM. mm.
.xampyt.nim
04.202.2A
01.109.01A
32.030.02A
09.046.0b
04.502.54b
06.054.0c
06.084.02c
02.600.6D
01.51D
06.604
.6E
07.41E
82.2e
06.404.41e
01.0153.9H
1L
08.21L
08.02L
106.04L
02.0R
V2 0 o8 o
TO-252 (DPAK) mechanical data
0068772_G
STD95N2LH5, STP95N2LH5, STU95N2LH5 Packaging mechanical data
Doc ID 13834 Rev 5 15/17
5 Packaging mechanical data
TAPE AND REEL SHIPMENT
DPAK FOOTPRINT
DIM. mm inch
MIN. MAX. MIN. MAX.
A 330 12.992
B1.5 0.059
C 12.8 13.2 0.504 0.520
D20.2 0.795
G 16.4 18.4 0.645 0.724
N50 1.968
T 22.4 0.881
BASE QTY BULK QTY
2500 2500
REEL MECHANICAL DATA
DIM. mm inch
MIN. MAX. MIN. MAX.
A0 6.8 7 0.267 0.275
B0 10.4 10.6 0.409 0.417
B1 12.1 0.476
D1.5 1.6 0.059 0.063
D1 1.5 0.059
E1.65 1.85 0.065 0.073
F 7.4 7.6 0.291 0.299
K0 2.55 2.75 0.100 0.108
P0 3.9 4.1 0.153 0.161
P1 7.9 8.1 0.311 0.319
P2 1.9 2.1 0.075 0.082
R40 1.574
W 15.7 16.3 0.618 0.641
TAPE MECHANICAL DATA
All dimensions are in millimeters
Revision history STD95N2LH5, STP95N2LH5, STU95N2LH5
16/17 Doc ID 13834 Rev 5
6 Revision history
29-
Table 8. Document revision history
Date Revision Changes
16-Oct-2007 1 First release
20-Feb-2008 2 Modified Table 4.: Static
23-Sep-2008 3 VGS value has been changed on Table 2 and Table 5
20-Apr-2009 4 Added device in TO-220
26-Apr-2010 5 –Table 1: Device summary has been corrected
–Section 4: Package mechanical data has been updated
STD95N2LH5, STP95N2LH5, STU95N2LH5
Doc ID 13834 Rev 5 17/17
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2010 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com