1
®
FN8222.3
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 |Intersil (and design) is a registered trademark of Intersil Americas Inc.
XDCP is a trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2005, 2006, 2009. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
X9C102, X9C103, X9C104, X9C503
Digitally Controlled Potentiometer
(XDCP™)
The X9C102, X9C103, X9C104, X9C503 are Intersils’
digitally controlled (XDCP) potentiometers. The device
consists of a resistor array, wiper switches, a control section,
and non-volatile memory. The wiper position is controlled by
a three-wire interface.
The potentiometer is implemented by a resistor ar ray
composed of 99 resistive elements and a wiper switching
network. Between each element and at either end are tap
points accessible to the wiper terminal. The position of the
wiper element is controlled by the CS, U/D, and INC inputs.
The position of the wiper can be stored in non-volatile
memory and then be recalled upon a subseque nt power-up
operation.
The device can be used as a three-terminal potentiometer or
as a two-terminal variable resistor in a wide vari ety of
applications ranging from control to signal processing to
parameter adjustment.
Pinout X9C102, X9C103, X9C104, X9C503
(8 LD SOIC, 8 LD PDIP)
TOP VIEW
Features
Solid-State Potentiometer
Three-Wire Serial Interface
100 Wiper Tap Point s
- Wiper Position Stored in Non-volatile Memory and
Recalled on Power-up
99 Resistive Elements
- Temperature Compensated
- End-to-End Resistance, ±20%
- Terminal Voltages, ±5V
Low Power CMOS
-V
CC = 5V
- Active Current, 3mA max.
- Standby Current, 750µA max.
High Reliability
- Endurance, 100 ,000 Data Changes per Bit
- Register Data Retention, 100 years
X9C102 = 1kΩ
X9C103 = 10kΩ
X9C503 = 50kΩ
X9C104 = 100kΩ
Packages
- 8 Ld SOIC
- 8 Ld PDIP
Pb-Free Available (RoHS Compliant)
Block Diagram
VCC
CS
VL/RL
VW/RW
INC
U/D
VH/RH
VSS
1
2
3
4
8
7
6
5
7-BIT
UP/DOWN
COUNTER
7-BIT
NON-VOLATILE
MEMORY
STORE AND
RECALL
CONTROL
CIRCUITRY
ONE
OF
HUNDRED
DECODER RESISTOR
ARRAY
RL/VL
RW/VW
RH/VH
U/D
INC
CS
TRANSFER
VCC
ONE-
GATES
99
98
97
96
2
1
0
GND
UP/DOWN
(INC)INCREMENT
DEVICE
(U/D)
(CS)
VCC (SUPPLY VOLTAGE)
VSS (GROUND)
CONTROL
AND
MEMORY
GENERAL
VH/RH
RW/VW
VL/RL
SELECT
DETAILED
Data Sheet July 20, 2009
2FN8222.3
July 20, 2009
Ordering Information
PART
NUMBER PART
MARKING RTOTAL
(kΩ)TEMP RANGE
(°C) PACKAGE PACKAGE
DWG. #
X9C102P X9C102P 1 0 to +70 8 Ld PDIP MDP0031
X9C102PZ (Notes 1, 2) X9C102P Z 0 to +70 8 Ld PDIP (Pb-free) MDP0031
X9C102PI X9C102P I -40 to +85 8 Ld PDIP MDP0031
X9C102PIZ (Notes 1, 2) X9C102P ZI -40 to +85 8 Ld PDIP (Pb-free) MDP0031
X9C102S*, ** X9C102S 0 to +70 8 Ld SOIC MDP0027
X9C102SZ* (Note 1) X9C102S Z 0 to +70 8 Ld SOIC (Pb-free) MDP0027
X9C102SI*, ** X9C102S I -40 to +85 8 Ld SOIC MDP0027
X9C102SIZ*, ** (Note 1) X9C102S ZI -40 to +85 8 Ld SOIC (Pb-free) MDP0027
X9C103P X9C103P 10 0 to +70 8 Ld PDIP MDP0031
X9C103PZ (Notes 1, 2) X9C103P Z 0 to +70 8 Ld PDIP (Pb-free) MDP0031
X9C103PI X9C103P I -40 to +85 8 Ld PDIP MDP0031
X9C103PIZ (Note 1) X9C103P ZI -40 to +85 8 Ld PDIP (Pb-free) MDP0031
X9C103S*, ** X9C103S 0 to +70 8 Ld SOIC MDP0027
X9C103SZ*, ** (Note 1) X9C103S Z 0 to +70 8 Ld SOIC (Pb-free) MDP0027
X9C103SI*, ** X9C103S I -40 to +85 8 Ld SOIC MDP0027
X9C103SIZ*, ** (Note 1) X9C103S ZI -40 to +85 8 Ld SOIC (Pb-free) MDP0027
X9C503P X9C503P 50 0 to +70 8 Ld PDIP MDP0031
X9C503PZ (Notes 1, 2) X9C503P Z 0 to +70 8 Ld PDIP (Pb-free) MDP0031
X9C503PI X9C503P I -40 to +85 8 Ld PDIP MDP0031
X9C503PIZ (Notes 1, 2) X9C503P ZI -40 to +85 8 Ld PDIP (Pb-free) MDP0031
X9C503S* X9C503S 0 to +70 8 Ld SOIC MDP0027
X9C503SZ* (Note 1) X9C503S Z 0 to +70 8 Ld SOIC (Pb-free) MDP0027
X9C503SI*, ** X9C503S I -40 to +85 8 Ld SOIC MDP0027
X9C503SIZ*, ** (Note 1) X9C503S ZI -40 to +85 8 Ld SOIC (Pb-free) MDP0027
X9C104P X9C104P 100 0 to +70 8 Ld PDIP MDP0031
X9C104PI X9C104P I -40 to +85 8 Ld PDIP MDP0031
X9C104PIZ (Notes 1, 2) X9C104P ZI -40 to +85 8 Ld PDIP (Pb-free) MDP0031
X9C104S*, ** X9C104S 0 to +70 8 Ld SOIC MDP0027
X9C104SZ*, ** (Note 1) X9C104S Z 0 to +70 8 Ld SOIC (Pb-free) MDP0027
X9C104SI*, ** X9C104S I -40 to +85 8 Ld SOIC MDP0027
X9C104SIZ*, ** (Note 1) X9C104S ZI -40 to +85 8 Ld SOIC (Pb-free) MDP0027
*Add “T1” suffix for tape and reel. Please refer to TB347 for details on reel specifications.
**Add “T2” suffix for tape and reel. Please refer to TB347 for details on reel specifications.
NOTES:
1. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100%
matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering
operations). Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free
requirements of IPC/JEDEC J STD-020.
2. Pb-free PDIPs can be used for through-hole wave solder processing only . They are not intended for use in Reflow solder processing applications.
X9C102, X9C103, X9C104, X9C503
3FN8222.3
July 20, 2009
Pin Descriptions
PIN
NUMBER PIN NAME DESCRIPTION
1INC
INCREMENT The INC input is negative-edge triggered. Toggling INC will move the wiper and either increment or
decrement the counter in the direction indicated by the logic level on the U/D input.
2U/D
UP/DOWN The U/D input controls the direction of the wiper movement and whether the counter is incremented or
decremented.
3V
H/RHVH/RH The high (VH/RH) terminals of the X9C102, X9C103, X9C104, X9C503 are equivalent to the fixed terminals of
a mechanical potentiometer. The minimum voltage is -5V and the maximum is +5V . The terminology of VH/RH and VL/RL
references the relative position of the terminal in relation to wiper movement direction selected by the U/D input and
not the voltage potential on the terminal.
4V
SS VSS
5V
W/RWVW/RW VW/RW is the wiper terminal and is equivalent to the movable terminal of a mechanical potentiometer. The
position of the wiper within the array is determined by the control inputs. The wiper terminal series resistance is typically
40Ω.
6R
L/VLRL/VL The low (VL/RL) terminals of the X9C102, X9C103, X9C104, X9C503 are equivalent to the fixed terminals of a
mechanical potentiometer . The minimum voltage is -5V and the maximum is +5V. The terminology of VH/RH and VL/RL
references the relative position of the terminal in relation to wiper movement direction selected by the U/D input and
not the voltage potential on the terminal.
7CS
CS The device is selected when the CS input is LOW . The current counter value is stored in non-volatile memory when
CS is returned HIGH while the INC input is also HIGH. After the store operation is complete the X9C102, X9C103,
X9C104, X9C503 device will be placed in the low power standby mode until the device is selected once again.
8V
CC VCC
X9C102, X9C103, X9C104, X9C503
4FN8222.3
July 20, 2009
Absolute Maximum Ratings Thermal Information
Voltage on CS, INC, U/D and VCC with Respect to VSS . -1V to +7V
Voltage on VH/RH and VL/RL Referenced to VSS. . . . . . . -8V to +8V
ΔV = |VH/RH - VL/RL|
X9C102 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4V
X9C103, X9C104, and X9C503 . . . . . . . . . . . . . . . . . . . . . . . .10V
IW (10s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8.8mA
Power Rating
X9C102 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16mW
X9C103 X0C104, and X9C503 . . . . . . . . . . . . . . . . . . . . . .10mW
Temperature Under Bias . . . . . . . . . . . . . . . . . . . . .-65°C to +135°C
Storage Temperature. . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Pb-Free Reflow Profile. . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
*Pb-free PDIPs can be used for through-hole wave solder
processing only. They are not intended for use in Reflow solder
processing applications.
Recommended Operating Conditions
Commercial Temperature Range. . . . . . . . . . . . . . . . . 0°C to +70°C
Industrial Temperature Range . . . . . . . . . . . . . . . . . .-40°C to +85°C
Supply Voltage Range (VCC). . . . . . . . . . . . . . . . . . . . . . . 5V ±10%
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
Electrical Specifications Over recommended operating conditions unless otherwise stated.
SYMBOL PARAMETER TEST CONDITIONS
LIMITS
UNITMIN TYP
(Note 6) MAX
POTENTIOMETER CHARACTERISTICS
RTOTAL End-to-End Resistance Variation -20 +20 %
VVH/RH VH Terminal Voltage -5 +5 V
VVL/RL VL Terminal Voltage -5 +5 V
IWWiper Current -4.4 4.4 mA
RWWiper Resistance Wiper Current = ±1mA 40 100 Ω
Resistor Noise (Note 7) Ref 1kHz -120 dBV
Charge Pump Noise (Note 7) @ 850kHz 20 mVRMS
Resolution 1%
Absolute Linearity (Note 3) VW(n)(actual) - VW(n)(EXPECTED) -1 +1 MI (Note 5)
Relative Linearity (Note 4) VW(n + 1)(ACTUAL) - [VW(n) + MI] -0.2 +0.2 MI (Note 5)
RTOTAL Temperature Coefficient X9C103, X9C503, X9C104 ±300 (Note 7) ppm/°C
RTOTAL Temperature Coefficient X9C102 ±600 (Note 7) ppm/°C
Ratiometric Temperature Coefficient ±20 ppm/°C
CH/CL/CW
(Note 7) Potentiometer Capacitances See “Circuit #3 SPICE Macro
Model” on page 5. 10/10/25 pF
DC OPERATING CHARACTERISTICS
ICC VCC Active Current CS = VIL, U/D = VIL or VIH and
INC = 0.4V to 2.4V at Max tCYC
13mA
ISB Standby Supply Current CS = VCC - 0.3V, U/D and
INC =V
SS or VCC -0.3V 200 750 µA
ILI CS, INC, U/D Input Leakage Current VIN = VSS to VCC ±10 µA
VIH CS, INC, U/D input HIGH Voltage 2 V
VIL CS, INC, U/D input LOW Voltage 0.8 V
CIN CS, INC, U/D Input Capacitance (Note 7) VCC = 5V, VIN = VSS, TA= +25°C,
f = 1MHz 10 pF
X9C102, X9C103, X9C104, X9C503
5FN8222.3
July 20, 2009
Power-up and Down Requirements
At all times, voltages on the potentiometer pins must be less
than ±VCC. The recall of the wiper position from non-volatile
memory is not in effect until the VCC supply reaches its final
value. The VCC ramp rate specification is always in effect.
AC OPERATION CHARACTERISTICS
tCl CS to INC Setup 100 ns
tlD INC HIGH to U/D Change 100 ns
tDI U/D to INC Setup 2.9 µs
tlL INC LOW Period 1 µs
tlH INC HIGH Period 1 µs
tlC INC Inactive to CS Inactive 1 µs
tCPH CS Deselect Time (STORE) 20 ms
tCPH CS Deselect Time (NO STORE) 100 ns
tIW (5) INC to VW/RW Change 100 µs
tCYC INC Cycle Time 2 µs
tCYC INC Input Rise and Fall Time 500 µs
tR, tFPower-up to Wiper Stable (Note 7) 500 µs
tPU VCC Power-up Rate (Note 7) 0.2 50 V/ms
NOTES:
3. Absolute linearity is utilized to determine actual wiper voltage vs expected voltage = [VW(n)(actual) - VW(n)(expected )] = ±1 MI Maximum.
4. Relative linearity is a measure of the error in step size between taps = VW(n + 1) - [VW(n) + MI] = +0.2 MI.
5. 1 MI = Minimum Increment = RTOT/99.
6. Typical values are for TA = +25°C and nominal supply voltage.
7. This parameter is not 100% tested.
Electrical Specifications Over recommended operating conditions unless otherwise stated. (Continued)
SYMBOL PARAMETER TEST CONDITIONS
LIMITS
UNITMIN TYP
(Note 6) MAX
Test Circuit #1
TEST POINT
Vw/RW
VR/RH
VL/RL
VS
Test Circuit #2
FORCE
VL/RL
VW/Rw
VH/RH
TEST POINT
CURRENT
Circuit #3 SPICE Macro Model
CW
RTOTAL
RLRH
CL
RW
10pF
CL
10pF
25pF
Endurance and Data Retention
PARAMETER MIN UNIT
Medium Endurance 100,000 Data changes per bit
per register
Data Retention 100 years
AC Conditions of Test
Input Pulse Levels 0V to 3V
Input Rise and Fall Times 10ns
Input Reference Levels 1.5V
X9C102, X9C103, X9C104, X9C503
6FN8222.3
July 20, 2009
AC Timing Diagram
Pin Descriptions
RH/VH and RL/VL
The high (VH/RH) and low (VL/RL) terminals of the
ISLX9C102, X9C103, X9C104, X9C5 03 are equivalent to
the fixed terminals of a mechanical potentiomete r. The
minimum voltage is -5V and the maximum is +5V. The
terminology of VH/RH an d VL/RL references the relative
position of the terminal in relation to wiper movement
direction selected by the U/D input and not the voltage
potential on the terminal.
RW/VW
VW/RW is the wiper terminal, and is equivalent to the
movable terminal of a mechanical potentiometer . The
position of the wiper within the array is determined by the
control inputs. The wiper terminal series resistance is typically
40Ω.
Up/Down (U/D)
The U/D input controls the direction of the wiper movement
and whether the counter is incremented or decremented.
Increment (INC)
The INC input is negative-edge triggered. Toggling INC will
move the wiper and either increment or decrement the
counter in the direction indicated by the logic level on the
U/D input.
Chip Select (CS)
The device is selected when the CS input is LOW. The
current counter value is stored in non-volatile me mory when
CS is returned HIGH while th e INC input is also HIGH. After
the store operation is complete the ISLX9C102, X9C103,
X9C104, X9C503 device will be placed in the low power
standby mode until the device is selected once again.
Principles of Operation
There are three sections of the X9C102, X9C103, ISL9C104
and ISL9C503: the input control, counter and decode section;
the non-volatile memory; and the resistor array. The input
control section operates just like an up/down counter. The
output of this counter is decoded to turn on a single electronic
switch connecting a point on the resistor array to the wiper
output. Under the proper conditions, the content s of the
counter can be stored in non-volatile memory and retained for
future use. The resistor array is comprised of 99 individual
resistors connected in series. At either end of the array and
between each resistor is an electronic switch that transfers the
potential at that point to the wiper.
The wiper, when at either fixed terminal, acts like its
mechanical equivalent and does not move beyond the last
position. That is, the counter does not wrap around when
clocked to either extreme.
The electronic switches on the device operate in a
“make-before-break” mode when the wiper changes tap
positions. If the wiper is moved several positions, multiple
taps are connected to the wiper for tIW (INC to VW/RW
change). The RTOTAL value for the device can temporarily be
reduced by a significant amount if the wiper is moved
several positions.
When the device is powered-down, the last wiper posi tio n
stored will be maintained in the non-volatile memory. When
power is restored, the contents of the memory are recalled
and the wiper is reset to the value last stored.
The internal charge pump allows a wide range of voltages
(from -5V to 5V) applied to XDCP terminals yet given a
convenience of single power supply. The typical charge
pump noise of 20mV at 850kHz should be taken in
consideration when designing an ap plication circuit.
CS
INC
U/D
VW
tCI tIL tIH
tCYC
tID tDI
tIW
MI
tIC tCPH
tFtR
10%
90% 90%
(NOTE)
NOTE: MI REFERS TO THE MINIMUM INCREMENTAL CHANGE IN THE VW OUTPUT DUE TO A CHANGE IN THE WIPER POSITION.
X9C102, X9C103, X9C104, X9C503
7FN8222.3
July 20, 2009
Instructions and Programming
The INC, U/D and CS inputs co ntrol th e mo vement of the
wiper along the resistor array. With CS set LOW , the device is
selected and enabled to respond to the U/D and INC input s.
HIGH to LOW transitions on INC will increment or decrement
(depending on the state of the U/D input) a 7-bit counter. The
output of th is counter is decoded to select one of one-hundred
wiper positions along the resistive array.
The value of the counter is stored in non-volatile memory
whenever CS transitions HIGH while the INC input is also
HIGH.
The system may select the X9Cxxx, move the wiper and
deselect the device without having to store the latest wiper
position in non-volatile memory. After the wiper movement is
performed as previously described and once the new
position is reached, the system must keep INC LOW while
taking CS HIGH. The new wiper position will be maintained
until changed by the system or until a power-down/up cycle
recalled the previously stored data.
This procedure allows the system to always power-up to a
pre-set value stored in non-volatile memory; then during
system operation, minor adjustments could be made. The
adjustments might be based on user preference, i.e.: system
parameter changes due to temperature drift, etc.
The state of U/D may be changed while CS remains LOW.
This allows the host system to enable the device and then
move the wiper up and down until the proper trim is attained.
Symbol Table
Performance Characteristics
Contact the factory for more info rmation.
Applications Information
Electronic digitally controlled (XCDP) potentiometers provide
three powerful application advantages:
1. The variability and reliability of a solid -state
potentiometer.
2. The flexibility of computer-ba sed digital controls.
3. The retentivity of non-volatile memory used for the
storage of multiple potentiometer settings or data.
Mode Selection
CS INC U/D MODE
L H Wiper Up
L L Wiper Down
H X Store Wiper Position
H X X Standby Current
L X No Store, Return to Standby
L H Wiper Up (not recommended)
L L Wiper Down (not recommended)
WAVEFORM INPUTS OUTPUTS
Must be
steady Will be
steady
May change
from Low to
High
Will change
from Low to
High
May change
from High to
Low
Will change
from High to
Low
Don’t Care:
Changes
Allowed
Changing:
State Not
Known
N/A Center Line
is High
Impedance
X9C102, X9C103, X9C104, X9C503
8FN8222.3
July 20, 2009
Basic Configurations of Electronic Potentiometers
Basic Circuits
VRVR
I
THREE TERMINAL POTENTIOMETER;
VARIABLE VOLTAGE DIVIDER TWO TERMINAL VARIABLE RESISTOR;
VARIABLE CURRENT
VH/RH
VL/RL
VW/RW
CASCADING TECHNIQUESBUFFERED REFERENCE VOLTAGE
+
+5V
R1
+V
-5V
VW
VREF VOUT
OP-07
VW/RW
VW/RW
+V
+V +V
X
(a) (b)
VOUT = VW/RW
NONINVERTING AMPLIFIER
VO = (1+R2/R1)VS
VOLTAGE REGULATOR
R1
R2
Iadj
VO (REG) = 1.25V (1+R2/R1)+Iadj R2
VO (REG)VIN 317
OFFSET VOLTAGE ADJUSTMENT
+
VS
VO
R2
R1
100kΩ
10kΩ10kΩ
10kΩ
-12V+12V
TL072
COMPARATOR WITH HYSTERESIS
VUL = {R1/(R1 + R2)} VO(MAX)
VLL = {R1/(R1 + R2)} VO(MIN)
+
VS
VO
R2
R1
LM308A
+5V
-5V
+
VS
VO
R2
R1
}
}
LT311A
(FOR ADDITIONAL CIRCUITS SEE AN1145)
X9C102, X9C103, X9C104, X9C503
9FN8222.3
July 20, 2009
X9C102, X9C103, X9C104, X9C503
Small Outline Package Family (SO)
GAUGE
PLANE
A2
A1 L
L1
DETAIL X 4° ±4°
SEATING
PLANE
eH
b
C
0.010 BMCA
0.004 C
0.010 BMCA
B
D
(N/2)
1
E1
E
NN (N/2)+1
A
PIN #1
I.D. MARK
h X 45°
A
SEE DETAIL “X”
c
0.010
MDP0027
SMALL OUTLINE PACKAGE FAMILY (SO)
SYMBOL
INCHES
TOLERANCE NOTESSO-8 SO-14
SO16
(0.150”)
SO16 (0.300”)
(SOL-16)
SO20
(SOL-20)
SO24
(SOL-24)
SO28
(SOL-28)
A 0.068 0.068 0.068 0.104 0.104 0.104 0.104 MAX -
A1 0.006 0.006 0.006 0.007 0.007 0.007 0.007 ±0.003 -
A2 0.057 0.057 0.057 0.092 0.092 0.092 0.092 ±0.002 -
b 0.017 0.017 0.017 0.017 0.017 0.017 0.017 ±0.003 -
c 0.009 0.009 0.009 0.011 0.011 0.011 0.011 ±0.001 -
D 0.193 0.341 0.390 0.406 0.504 0.606 0.704 ±0.004 1, 3
E 0.236 0.236 0.236 0.406 0.406 0.406 0.406 ±0.008 -
E1 0.154 0.154 0.154 0.295 0.295 0.295 0.295 ±0.004 2, 3
e 0.050 0.050 0.050 0.050 0.050 0.050 0.050 Basic -
L 0.025 0.025 0.025 0.030 0.030 0.030 0.030 ±0.009 -
L1 0.041 0.041 0.041 0.056 0.056 0.056 0.056 Basic -
h 0.013 0.013 0.013 0.020 0.020 0.020 0.020 Reference -
N 8 14 16 16 20 24 28 Reference -
Rev. M 2/07
NOTES:
1. Plastic or metal protrusions of 0.006” maximum per side are not included.
2. Plastic interlead protrusions of 0.010” maximum per side are not included.
3. Dimensions “D” and “E1” are measured at Datum Plane “H”.
4. Dimensioning and tolerancing per ASME Y14.5M-1994
10
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No lice nse is gran t ed by i mpli catio n or other wise u nder an y p a tent or patent right s of Int ersi l or it s sub sidi aries.
For information regarding Intersil Corporation and its products, see www.intersil.com
FN8222.3
July 20, 2009
X9C102, X9C103, X9C104, X9C503
Plastic Dual-In-Line Packages (PDIP)
MDP0031
PLASTIC DUAL-IN-LINE PACKAGE
SYMBOL
INCHES
TOLERANCE NOTESPDIP8 PDIP14 PDIP16 PDIP18 PDIP20
A 0.210 0.210 0.210 0.210 0.210 MAX
A1 0.015 0.015 0.015 0.015 0.015 MIN
A2 0.130 0.130 0.130 0.130 0.130 ±0.005
b 0.018 0.018 0.018 0.018 0.018 ±0.002
b2 0.060 0.060 0.060 0.060 0.060 +0.010/-0.015
c 0.010 0.010 0.010 0.010 0.010 +0.004/-0.002
D 0.375 0.750 0.750 0.890 1.020 ±0.010 1
E 0.310 0.310 0.310 0.310 0.310 +0.015/-0.010
E1 0.250 0.250 0.250 0.250 0.250 ±0.005 2
e 0.100 0.100 0.100 0.100 0.100 Basic
eA 0.300 0.300 0.300 0.300 0.300 Basic
eB 0.345 0.345 0.345 0.345 0.345 ±0.025
L 0.125 0.125 0.125 0.125 0.125 ±0.010
N 8 14 16 18 20 Reference
Rev. C 2/07
NOTES:
1. Plastic or metal protrusions of 0.010” maximum per side are not included.
2. Plastic interlead protrusions of 0.010” maximum per side are not included.
3. Dimensions E and eA are measured with the leads constrained perpendicular to the seating plane.
4. Dimension eB is measured with the lead tips unconstrained.
5. 8 and 16 lead packages have half end-leads as shown.
D
L
A
eb
A1
NOTE 5
A2
SEATING
PLANE
L
N
PIN #1
INDEX
E1
12 N/2
b2
E
eB
eA
c