C
0.70
(17.8)
0.60
(15.2)
0.02
(0.5)
0.375
(9.53)
Mount End Barrier End
Mount End Barrier End
B Pole Centers
A Mount Centers
0.19
(4.8)
Ø
0.32
(8.1)
C
A Mount Centers
0.65
(16.5)
B Pole Centers
0.375
(9.53)
Mount End Barrier End
Mount End Barrier End
0.40
(10.2)
0.76 (19.3)
0.565 (14.35)
on LP2000
0.15
(3.8)
Ø
0.02
(0.5)
MOUNTING BARRIER & BARRIER
ENDS MOUNTING ENDS
ONLY ENDS ONLY
ACBC
Poles Mount Ctrs. Length Pole Ctrs. Length
02 1.13 1.56 0.38 0.81
03 1.50 1.93 0.75 1.18
04 1.88 2.30 1.13 1.56
05 2.25 2.68 1.50 1.93
06 2.63 3.06 1.88 2.31
07 3.00 3.43 2.25 2.68
08 3.38 3.81 2.63 3.06
09 3.75 4.18 3.00 3.43
10 4.13 4.56 3.38 3.81
11 4.50 4.93 3.75 4.18
12 4.88 5.31 4.13 4.56
13 5.25 5.69 4.50 4.93
14 5.63 6.06 4.88 5.31
15 6.00 6.43 5.25 5.68
16 6.38 6.81 5.63 6.06
17 6.75 7.18 6.00 6.43
18 7.13 7.56 6.38 6.81
19 7.50 7.93 6.75 7.18
20 7.88 8.31 7.13 7.56
21 8.25 8.68 7.50 7.93
22 8.63 9.06 7.88 8.31
23 9.00 9.43 8.25 8.68
24 9.38 9.81 8.63 9.06
25 9.75 10.18 9.00 9.43
26 10.13 10.56 9.38 9.81
27 10.50 10.93 9.75 10.18
28 10.88 11.31 10.13 10.55
29 11.25 11.68 10.50 10.93
30 11.63 12.05 10.88 11.31
31 – – 11.25 11.68
32 – – 11.63 12.05
Series A2000, LP2000 & CB2000
Single Row Terminal Blocks
SPECIFICATIONS
Rating: A2: 30A, 300V*
LP2: 30A, 150V*
CB2: 30A, 300V*
Center Spacing: 0.375” or 3/8” (9.52mm)
Wire Range: #12-22 AWG CU
Screw Size: #6-32 zinc-plated philslot
Torque Rating: 9 lb-in.
Base: Standoffs standard for easy flux washing
Distance Between Barriers: 0.32” (8.1mm)
Recommended PCB Hole Diameter: 0.076” (1.93mm)
Operating Temperature: 105°C (221°F) max., -40°C (-40°F) min.
Molded Material: Black, UL Rated 94V0 Thermoplastic
Breakdown Voltage: 3400V (A2 & LP2); 4100V (CB2).
Agency Information: UL File E62622, CSA File 47235;
IEC Compliance; CE Certified
*30A Rating achieved with a #10 copper wire crimped to a ring terminal.;
20A Rating without ring terminal.
LP202110
A2000 & LP2000 Series
Dimensions - in (mm)
* Dimensions in inches. To convert to millimeters, multiply by 25.4.
A20510807WR
CB2000 Series
CB20210507
Terminal Blocks - Single Row
Terminal Blocks:
Single & Double Row EuroMag Series Terminal Blocks:
Base & Rail Mount Power Distribution
Blocks Wire Management
Products Edge Connectors,
One-Sided Boards Compliance
References
Series A2000 & LP2000
Single Row Terminal Blocks
Part Numbering System
Series Terminal Style Base/End Poles Screw Options Options
A2
- standard barrier
01
- handwired
0
- flat base/molded
02
to
32 Blank
- std. screw
AB
- angle mnt. options (pg 9)
LP2
- low profile
02
- printed circuit mount end
02
to
30
on mount
00
- screws shipped bulk
A1
to
A9
- 0.250˝ QC
barrier
03
- non feed-thru
1
- flat base/mnt. end end base
03
- stainless steel
B1
to
B9
- 0.187˝ QC
04
- wire wrap tail
2
- flat base/barrier end
04
- brass nickel-plated
DR
- drilled right angle (pg 9)
05
- extended handwired
3
- insulator base/mnt. end
07
- steel SEMS †
JA
,
JB
&
JC
- barrier jumpers
06
- handwired
4
- insulator base/ (not available
L1
to
L6
marking options (pg 22)
07
- extended pin barrier end with hardware options)
MP, MP8
&
MT
mounting plates (pg 9)
08
- printed circuit
5
- closed base/
09
- brass SEMS †
OJ2
&
OJ4
- over barrier jumpers (not
09
- 0.250˝ QC short mount end nickel-plated available w/covers)
10
- 0.187˝ QC
6
- closed base/ (not available with
RC
- retaining clips (pg 9)
14
- printed circuit molded mount end hardware options
)
R30
to
R77
- right angle bends (pg 9)
19
- 0.250˝ QC long
9
- insulator base/
CA
- captive screw
SO
- stand off insulators (pg 9)
molded mount end
WR
- wire ready
S1
- solder lug/flat
(not available on LP2
series)
Covers
- (pg 23)
0.20
(5.1)
0.062
(1.57)
0.031
(0.79)
0.55
(14.0)
0.062
(1.57)
0.031
(0.79)
01
Handwired 04
Wire Wrap Tail
03
Non Feed-Thru
02
Printed Circuit
0.54
(13.7)
0.055
(1.40)
0.032
(0.81)
0.14
(3.6)
07
Extended Pin
0.11
(2.79)
0.031
(0.79)
0.30
(7.6)
06
Handwired
Terminal Styles Inches (Millimeters)
0.062
(1.57)
0.17
(4.3)
0.031
(0.79)
0.42
(10.7)
0.187
(4.75)
0.031
(0.79)
0.40
(10.2)
0.250
(6.35)
0.031
(0.79)
08
Printed Circuit
10
0.187˝ QC
09
0.250˝ QC short
0.72
(18.3)
0.31
(7.9)
0.41
(10.4)
0.33
(8.4)
0.250
(6.35)
0.031
(0.79)
19
√0.250˝ QC long
0.062
(1.57)
0.031
(0.79) 0.125
(3.2)
14
Printed Circuit
A 2
L P 2
Base/End Note: 0, 6,
9 styles not available
with covers. 5 & 6
Styles only available
with 03 terminals.
0.66
(16.8)
0.110
(2.79)
0.031
(0.79)
05
Extended Handwired
0.55
(14.0)
0.110
(2.79)
0.031
(.79)
†Contact factory for configuration...
Terminal Blocks - Single Row
Hardware Options (Bulk ordering part numbers are in parentheses.) Inches (Millimeters)
Solder Lugs Jumpers Quick Connects
Blade Width A = 0.250” Blade Width B = 0.187”
0.68 (17.3)
0.84 (21.2)
S1
(2S1-J) A1 &B1
(2A1-J &2B1-J) A2 &B2
(2A2-J &2B2-J) A3 &B3
(2A3-J &2B3-J)
A9 &B9
(2A9-J &2B9-J)
0.33 (8.4)
†JB
(JB2-XX-J) A4 &B4
(2A4-J &2B4-J) A5 &B5
(2A5-J &2B5-J) A6 &B6
(2A6-J &2B6-J)
A7 &B7
(2A7-J &2B7-J) A8 &B8
(2A8-J &2B8-J)
0.33 (8.4)
†JA
(JA2-XX-J)
0.33 (8.4)
†JC
(JC2-XX-J)
WR
Wire Ready
04
Brass
Nickel-Plated
07
Steel SEMS
Screw Options
09
Brass SEMS
Nickel-Plated
†OJ4
(OJ4-J)
†OJ2
(OJ2-J)
B
SECTION A–A
0.40
(10.2)
B
0.180 (4.57)
0.218 (5.54)
B
0.150 Ø (3.8)
mounting holes (2)
0.095
(2.4)
SECTION B–B
0.40
(10.2)
B
0, 6 & 9
Molded Mount End 1, 3 & 5
Mount End
03
Stainless Steel
Standard
zinc-plated Steel
Base/End Options Inches (Millimeters)
Series A2000 & LP2000
Single Row Terminal Blocks Continued
†Contact factory for configuration.
Terminal Blocks - Single Row
MOUNTING
PLATE
;
MP
MP8
;
MT
0.144 HOLE
w/0.312 C' BORE
0.325
0.12
Options MP, MP8 & MT
MP Metal inserts with 0.150” dia. hole
accept #6 screw. MP8 Metal inserts with
0.187” dia. hole accept #8-32 screw. MT
Metal inserts with tapped hole accept #6-32
screw.
Option DR
Counterbored holes across mount ends of
block enable fastening with two screws at
right angles to normal mount position.
Drilled Right Angle (A2, LP2 only)
Mounting Plates
STANDOFF
0.300
Option SO
Standoff mounts are tubes molded to the
mounting positions. Available with insulator
bases only.
Retaining ClipStandoffs
;
Option RC
Use on standoff tubes. Fit panels up to
0.125” thick. Two clips for every five
positions. Supplied unassembled. Bulk part
number H541-J.
Mounting Options
0.32
0.45
0.15
0.25
0.04
Option AB
Angle brackets enable block to be fastened
at right angles to normal mount position.
Bulk part number 2AB-J.
Angle Brackets (A2, LP2 only)
Right Angle Bends (A2, LP2 only)
Right angle terminals are offered on the A2000 & LP2000 Series.
Configurations are defined in these dimensions: X = pin extension beyond the
block base; Z = length from block base to centerline of the terminal tip.
Standard bends consist of the X and Z dimensions shown in the chart.
Specify by adding the selected Bend Option Code to the terminal part
number.
X
Z
0.82
X
Z
0.55
07 Terminal Bend Configurations
04 Terminal Bend Configurations
Bend Available
Option X Z w/insulator
Code (minimum) base
R30 0.04 0.28 No
R35 0.01 0.23 No
R36 0.02 0.22 No
R39 0.05 0.19 No
R42 0.08 0.16 No
R46 0.12 0.12 No
R48 0.14 0.10 No
R50 0.16 0.08 No
Bend Available
Option X Z w/insulator
Code (minimum) base
R30 0.04 0.55 Yes
R35 0.01 0.50 Yes
R36 0.02 0.49 Yes
R42 0.08 0.43 Yes
R46 0.12 0.39 Yes
R50 0.16 0.35 No
R53 0.19 0.32 No
R66 0.32 0.19 No
R69 0.35 0.16 No
R75 0.41 0.10 No
R77 0.43 0.08 No
Dimensions in inches. To convert to millimeters, multiply by 25.4.
Series A2000 & LP2000
Single Row Terminal Blocks Continued
Terminal Blocks - Single Row
0.19
(4.8 )
0.045
(1.14)
0.031
(0.79)
0.18
(4.6)
02
Printed Circuit 03
Non Feed-Thru
Available on Mount
End (1) only.
Series Terminal Style Base/End Poles Screws Options
CB2
- closed back
01
- handwired
1
- mount end
02
to
32 03
- stainless steel *
AB
- angle mounting brackets (pg 11)
02
- printed circuit
2
- barrier end
02
to
30
on mount
04
- brass nickel-plated
A7
to
A9
- 0.250” QC
03
- non feed-thru end base
07
- steel SEMS
B7
to
B9
- 0.187” QC
07
- extended pin standard
EB
- exit back terminals
14
- printed circuit
09
- brass SEMS
EF
- exit front terminals
22
- dual tail printed circuit nickel-plated †
JA
,
JB
&
JC
- barrier jumpers
CA
- captive screw
L1
to
L6
marking options (pg 22)
07CA
- SEMS captive
LT1
to
LT6
marking options (pg 22)
†
OJ2
&
OJ4
- over barrier jumpers
MP, MP8, MT
&
MT8
mtg. plates (pg 11)
S1
- solder lug/flat
0.40
(10.2)
0.120
(3.05)
0.031
(0.79)
0.18
(4.6)
07
Steel SEMS
zinc-plated
(BOO1-7084-J)
0.125
(3.18)
0.045
(1.14)
0.031
(0.79)
0.18
(4.6)
14
Printed Circuit
0.19
(4.9)
0.045
(1.14) 0.03
(0.79)
0.81
(4.6)
0.40
(10.2)
0.43
(10.9)
22
Dual Tail
Printred Circuit
0.70
(17.8)
0.062
(1.57)
0.031
(0.79)
0.18
(4.6)
07
Extended Pin
Screw Options (Bulk ordering part numbers are in parentheses.)
Terminal Styles Inches (Millimeters)
Series CB2000
Single Row Terminal Blocks
Part Numbering System
01
Handwired
Exit Rear (std.) EF Exit Front EB Exit Back
CB2 T
erminal Exit Options Inches (Millimeters)
0.18
(4.6)
0.255
(6.48)
0.18
(4.6) X
CB2
09
Brass SEMS
nickel-plated
(F524-J)
04
Brass
nickel-plated
(F506-J)
03
Stainless Steel
(F507-J)
* NOTE: Wire ready screws standard on all terminal styles.
*Only available on 3-poles and up.
†Contact factory for configuration..
Terminal Blocks - Single Row
MOUNTING
PLATE
;
MP
MP8
;
MT
MT8
Hardware Options (Bulk ordering part numbers are in parentheses.) Inches (Millimeters)
Solder Lugs Jumpers Quick Connects
Blade Width A = 0.250”. Blade Width B = 0.187”.
0.68 (17.3)
0.84 (21.2)
S1
(2S1-J) A9 &B9
(2A9-J &2B9-J)
0.33 (8.4)
†JB
(JB2-XX-J)
A7 &B7
(2A7-J &2B7-J) A8 &B8
(2A8-J &2B8-J)
0.33 (8.4)
†JA
(JA2-XX-J)
0.33 (8.4)
†JC
(JC2-XX-J)
Mounting Options Inches (Millimeters)
Snap-in Angle Bracket Chassis
or PCB
A
A
#6 or #8
mounting
screw & nut
(Customer
supplied.)
0.71
(18.0)
0.45
(11.4)
0.79
(20.1)
1.02
(25.8)
0.24
(6.1)
0.42
(10.7)
Option AB
†OJ4
(OJ4-J)
†OJ2
(OJ2-J)
Options MP, MP8, MT & MT8
MP Metal inserts with 0.150” dia. hole accept #6 screw.
MP8 Metal inserts with 0.187” dia. hole accept #8-32 screw.
MT Metal inserts with tapped hole accept #6-32 screw.
MT8 Metal inserts with tapped hole accept #8-32 screw.
Mounting Plates
End Positions
usable
Exit Back (EB)
Terminals
Angle
Bracket
Right Angle Mounting Bracket
Mounts blocks on PC boards at a right angle.
• Protects solder joints.
• Recommended for all EB (Exit Back) PCB terminal blocks.
• Bracket snaps securely on block (no hardware required).
• Minimum strip length (end positions are usable).
• Mount with #6-32 or #8-32 screws (not supplied).
Series CB2000
Single Row Terminal Blocks
†Contact factory for configuration..
Terminal Blocks - Single Row
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Cooper Bussmann:
OJ4/J A201302 A202202 A202203 A20220307L1 A210406 A214204 A207006R42DR
Eaton:
A207409 A208205 A210310 A20440404 A201321 A203117B7 A20221009 A203603 A20221603 A20222107
A207305R35 A204212 A203102A3 A20441603 A203516 A20711604MP A207216R53 A20221404 A207203R53
A209108 A20431607 A20310807 A207303R35 A20120607 A208112 A207212R35 A20130507L1 A20220504
A204202 A20130900MP A203105 A20710807 A20222603 A204410 A20731207CAR50 A20821004
A20350807MP A203503B9 A207306R46SO A21420307 A207416 A20220607CA A21020307 A20110904
A20610604 A20220903 A20222407 A20130807 A20130307 A20741203 A20220207L1 A204217 A209104
A204204R35 A206112 A20420707 A207202R46 A20140807RC A20220404 A205312 A20221007CA A209103
A207207 A20220907CA A20720607R75 A20130407 A20111004 A20220704 A207407 A206205CA A21420407
A204412 A202230 A20420604 A202219 A210306 A207324 A21422307 A20740309 A20310907 A204203
A20350607S1L1 A204209 A20720807R46 A203105B9 A20432004 A20420507 A20741307R46 A20221103
A20312407 A20820204 A20820507WR A207306 A206014 A203506MP A20220507WR A20220804 A201413RC
A203514MP A209112