10 MHz Bandwidth, 640 MSPS
Dual Continuous Time Sigma-Delta Modulator
AD9267
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 www.analog.com
Fax: 781.461.3113 ©2009 Analog Devices, Inc. All rights reserved.
FEATURES
SNR: 83 dB (85 dBFS) to 10 MHz input
SFDR: −88 dBc to 10 MHz input
Noise figure: 15 dB
Input impedance: 1 kΩ
Power: 416 mW
10 MHz real or 20 MHz complex bandwidth
1.8 V analog supply operation
On-chip PLL clock multiplier
On-chip voltage reference
Twos complement data format
640 MSPS, 4-bit LVDS data output
Serial control interface (SPI)
APPLICATIONS
Baseband quadrature receivers: CDMA2000, W-CDMA,
multicarrier GSM/EDGE, 802.16x, and LTE
Quadrature sampling instrumentation
GENERAL DESCRIPTION
The AD9267 is a dual continuous time (CT) sigma-delta (Σ-Δ)
modulator with −88 dBc of dynamic range over 10 MHz real
or 20 MHz complex bandwidth. The combination of high
dynamic range, wide bandwidth, and characteristics unique
to the continuous time Σ-Δ modulator architecture makes the
AD9267 an ideal solution for wireless communication systems.
The AD9267 has a resistive input impedance that significantly
relaxes the requirements of the driver amplifier. In addition, a
32× oversampled fifth-order continuous time loop filter attenuates
out-of-band signals and aliases, reducing the need for external
filters at the input. The low noise figure of 15 dB relaxes the
linearity requirements of the front-end signal chain components,
and the high dynamic range reduces the need for an automatic
gain control (AGC) loop.
A differential input clock controls all internal conversion cycles.
An external clock input or the integrated integer-N PLL provides
the 640 MHz internal clock needed for the oversampled conti-
nuous time Σ-Δ modulator. The digital output data is presented
as 4-bit, LVDS at 640 MSPS in twos complement format. A data
clock output (DCO) is provided to ensure proper latch timing
with receiving logic. Additional digital signal processing may be
required on the 4-bit modulator output to remove the out-of-band
noise and to reduce the sample rate.
FUNCTIONAL BLOCK DIAGRAM
VIN+A
VIN–A
VIN+B
VIN–B
VREF
CFILT
07773-001
PHASE-
LOCKED
LOOP
SERIAL
INTERFACE
LVDS
DRIVERS
LVDS
DRIVERS
Σ-Δ
MODULATOR
Σ-Δ
MODULATOR
AGND SDIO/
PLLMULT1 SCLK/
PLLMULT0 DGNDCSB
A
V
DD PDWNB PDWN
A
DR
V
DD
AD9267
D3±A
OR±A
D0±A
D3±B
D0±B
CLK+
PLLMULT2
PLLMULT3
PLLMULT4
PLL_LOCKED
CLK–
DCO±
OR±B
Figure 1.
The AD9267 operates on a 1.8 V power supply, consuming
416 mW. The AD9267 is available in a 64-lead LFCSP and
is specified over the industrial temperature range (−40°C
to +85°C).
PRODUCT HIGHLIGHTS
1. Continuous time Σ-Δ architecture efficiently achieves high
dynamic range and wide bandwidth.
2. Passive input structure reduces or eliminates the require-
ments for a driver amplifier.
3. An oversampling ratio of 32× and high order loop filter
provide excellent alias rejection, reducing or eliminating
the need for antialiasing filters.
4. Operates from a single 1.8 V power supply.
5. A standard serial port interface (SPI) supports various
product features and functions.
6. Features a low pin count, high speed LVDS interface with
data output clock.
AD9267
Rev. 0 | Page 2 of 24
TABLE OF CONTENTS
Features .............................................................................................. 1
Applications ....................................................................................... 1
General Description ......................................................................... 1
Functional Block Diagram .............................................................. 1
Product Highlights ........................................................................... 1
Revision History ............................................................................... 2
Specifications ..................................................................................... 3
DC Specifications ......................................................................... 3
AC Specifications .......................................................................... 4
Digital Specifications ................................................................... 5
Switching Specifications .............................................................. 6
Absolute Maximum Ratings ............................................................ 7
Thermal Resistance ...................................................................... 7
ESD Caution .................................................................................. 7
Pin Configuration and Function Descriptions ............................. 8
Typical Performance Characteristics ............................................. 9
Equivalent Circuits ......................................................................... 12
Theory of Operation ...................................................................... 13
Analog Input Considerations ................................................... 13
Clock Input Considerations ...................................................... 14
Power Dissipation and Standby Mode .................................... 17
Digital Outputs ........................................................................... 17
Timing ......................................................................................... 18
Serial Port Interface (SPI) .............................................................. 19
Configuration Using the SPI ..................................................... 19
Hardware Interface ..................................................................... 20
Applications Information .............................................................. 21
Filtering Requirement ................................................................ 21
Memory Map .................................................................................. 23
Memory Map Definitions ......................................................... 23
Outline Dimensions ....................................................................... 24
Ordering Guide .......................................................................... 24
REVISION HISTORY
7/09—Revision 0: Initial Version
AD9267
Rev. 0 | Page 3 of 24
SPECIFICATIONS
DC SPECIFICATIONS
All power supplies set to 1.8 V, 640 MHz sample rate, 0.5 V internal reference, PLL disabled, AIN1 = −2.0 dBFS, unless otherwise noted.
Table 1.
Parameter Temp Min Typ Max Unit
RESOLUTION Full 16 Bits
ANALOG INPUT BANDWIDTH 10 MHz
ACCURACY
No Missing Codes Full Guaranteed
Offset Error Full ±0.025 ±0.2 % FSR
Gain Error Full ±0.7 ±2.5 % FSR
Integral Nonlinearity (INL)2 25°C ±1.5 LSB
MATCHING CHARACTERISTIC
Offset Error Full ±0.035 ±0.2 % FSR
Gain Error Full ±0.2 ±1.2 % FSR
TEMPERATURE DRIFT
Offset Error Full ±1.5 ppm/°C
Gain Error Full ±47 ppm/°C
INTERNAL VOLTAGE REFERENCE Full 496 500 505 mV
ANALOG INPUT
Input Span, VREF = 0.5 V Full 2 V p-p diff
Input Resistance Full 1 kΩ
Input Common Mode Full 1.7 1.8 1.9 V
POWER SUPPLIES
Supply Voltage
AVDD Full 1.7 1.8 1.9 V
CVDD Full 1.7 1.8 1.9 V
DVDD Full 1.7 1.8 1.9 V
DRVDD Full 1.7 1.8 1.9 V
Supply Current
IAVDD2, PLL Enabled Full 150.7 162 mA
IAVDD2, PLL Disabled Full 151.2 161 mA
ICVDD2, PLL Enabled Full 57 63 mA
ICVDD2, PLL Disabled Full 8 9.2 mA
IDVDD2 Full 71.5 78 mA
IDRVDD2 Full 0.26 0.3 mA
POWER CONSUMPTION
Sine Wave Input2, PLL Disabled Full 416 mW
Sine Wave Input, PLL Enabled Full 503 mW
Power-Down Power 25°C 110 mW
Standby Power 25°C 9 mW
Sleep Power Full 3 4 mW
1 Input power is referenced to full scale. Therefore, all measurements were taken with a 2 dB signal below full scale, unless otherwise noted.
2 Measured with a low input frequency, full-scale sine wave with approximately 5 pF loading on each output bit.
AD9267
Rev. 0 | Page 4 of 24
AC SPECIFICATIONS
All power supplies set to 1.8 V, 640 MHz sample rate, 0.5 V internal reference, PLL disabled, AIN1 = −2.0 dBFS, unless otherwise noted.
Table 2.
Parameter2 Temp Min Typ Max Unit
SIGNAL-TO-NOISE RATIO (SNR)
fIN = 2.4 MHz Full 81 83 dB
fIN = 4.2 MHz 25°C 83 dB
fIN = 8.4 MHz 25°C 83 dB
SPURIOUS-FREE DYNAMIC RANGE (WORST SECOND OR THIRD HARMONIC)3
fIN = 2.4 MHz Full −88 −80 dBc
fIN = 4.2 MHz 25°C −88 dBc
fIN = 8.4 MHz 25°C <−120 dBc
NOISE SPECTRAL DENSITY
AIN = −2 dBFS Full −155 −153 dBFS/Hz
AIN = −40 dBFS Full −156 −155 dBFS/Hz
NOISE FIGURE2, 4
AIN = −2 dBFS 25°C 16 dB
AIN = −40 dBFS 25°C 15 dB
TWO-TONE SFDR
fIN1 = 1.8 MHz @ −8 dBFS, fIN2 = 2.1 MHz @ −8 dBFS 25°C −89.5 dBc
fIN1 = 3.7 MHz @ −8 dBFS, fIN2 = 4.2 MHz @ −8 dBFS 25°C −93 dBc
fIN1 = 7.2 MHz @ −8 dBFS, fIN2 = 8.4 MHz @ −8 dBFS 25°C −87 dBc
ANALOG INPUT BANDWIDTH 25°C 10 MHz
1 Input power is referenced to full scale. Therefore, all measurements were taken with a 2 dB signal below full scale, unless otherwise noted.
2 See the AN-835 Application Note, Understanding High Speed ADC Testing and Evaluation, for a complete set of definitions.
3 Spurious-free dynamic range excluding the second or third harmonic is limited by the FFT size, <−120 dBFS.
4 Noise figure with respect to 50 Ω. AD9267 internal impedance is 1000 Ω differential. See the AN-835 for a definition.
AD9267
Rev. 0 | Page 5 of 24
DIGITAL SPECIFICATIONS
All power supplies set to 1.8 V, 640 MHz sample rate, 2 V p-p differential input, 0.5 V internal reference, PLL disabled, AIN = −2.0 dBFS,
unless otherwise noted.
Table 3.
Parameter Temp Min Typ Max Unit
DIFFERENTIAL CLOCK INPUTS (CLK+, CLK−)
Logic Compliance CMOS1/LVDS/LVPECL
Differential Input Voltage Full 0.4 0.8 2 V p-p
Input Common-Mode Range Full 450 mV
High Level Input Current Full −60 +60 µA
Low Level Input Current Full −60 +60 µA
Input Resistance Full 20 kΩ diff
Input Capacitance Full 1 pF
LOGIC INPUTS (SCLK)
High Level Input Voltage Full 1.2 DRVDD + 0.3 V
Low Level Input Voltage Full 0 0.8 V
High Level Input Current Full −50 −75 µA
Low Level Input Current Full −10 +10 µA
Input Resistance Full 30 kΩ
Input Capacitance Full 2 pF
LOGIC INPUTS (SDIO, CSB, RESET)
High Level Input Voltage Full 1.2 DRVDD + 0.3 V
Low Level Input Voltage Full 0 0.8 V
High Level Input Current Full −10 +10 µA
Low Level Input Current Full +40 +135 µA
Input Resistance Full 26 kΩ
Input Capacitance Full 5 pF
DIGITAL OUTPUTS (D0±x to D3±x)
ANSI-644
Logic Compliance LVDS
Differential Output Voltage (VOD) Full 247 454 mV
Output Offset Voltage (VOS) Full 1.125 1.375 V
Output Coding (Default) Twos complement
Low Power, Reduced Signal Option
Logic Compliance LVDS
Differential Output Voltage (VOD) Full 150 250 mV
Output Offset Voltage (VOS) Full 1.10 1.30 V
Output Coding (Default) Twos complement
1 For voltage swings beyond the specified range, clamping diodes are recommended.
AD9267
Rev. 0 | Page 6 of 24
SWITCHING SPECIFICATIONS
AVDD = 1.8 V, DRVDD = 1.8 V, unless otherwise noted.
Table 4.
Parameter1 Conditions/Comments Temp Min Typ Max Unit
CLOCK INPUT PARAMETERS Using clock multiplier
Input CLK Rate Full 30 160 MSPS
CLK± Period Full 6.25 33.3 ns
CLK± Duty Cycle Full 40 50 60 %
CLOCK INPUT PARAMETERS Direct clocking
Conversion Rate Full 608 640 672 MSPS
CLK± Period Full 1.48 1.5625 1.72 ns
CLK± Duty Cycle Full 40 50 60 %
DATA OUTPUT PARAMETERS
Data Propagation Delay (tPD)2 Full
160 510 840 ps
DCO± Propagation Delay (tDCO) Full
-60 268 570 ps
DCO± to Data Skew (tSKEW) Full
180 200 280 Ps
Aperture Uncertainty (Jitter, tJ) Full
1 ps rms
WAKE-UP TIME
Power-Down Power 25°C 3 Μs
Standby Power 25°C 9 s
Sleep Power 25°C 15 s
OUT-OF-RANGE RECOVERY TIME 25°C 100 ns
SERIAL PORT INTERFACE3
SCLK Period (tSCLK) Full
40 ns
SCLK Pulse Width High Time (tSHIGH) Full
16 ns
SCLK Pulse Width Low Time (tSLOW) Full
16 ns
SDIO to SCLK Set-Up Time (tSDS) Full
5 ns
SDIO to SCLK Hold Time (tSDH) Full
2 ns
CSB to SCLK Set-Up Time (tSS) Full 5 ns
CSB to SCLK Hold Time (tSH) Full 2 ns
1 See the AN-835 Application Note, Understanding High Speed ADC Testing and Evaluation, for a complete set of definitions.
2 Output propagation delay is measured from CLK± 50% transition to data D0±x to D3±x 50% transition, with 5 pF load.
3 See Figure 42 and the Serial Port Interface (SPI) section.
Timing Diagram
07773-057
CLK±
DCO±
D0±x TO D3±x
t
PD
t
DCO
t
SKEW
Figure 2. Timing Diagram
AD9267
Rev. 0 | Page 7 of 24
ABSOLUTE MAXIMUM RATINGS
Table 5.
Parameter Rating
Electrical
AVDD to AGND −0.3 V to +2.0 V
DVDD to DGND −0.3 V to +2.0 V
DRVDD to DGND −0.3 V to +3.9 V
AGND to DGND −0.3 V to +0.3 V
AVDD to DRVDD −3.9 V to +2.0 V
CVDD to CGND −0.3 V to +2.0 V
CGND to DGND −0.3 V to +0.3 V
D0±A to D3±A to DGND −0.3 V to +2.0 V
D0±B to D3±B to DGND −0.3 V to +2.0 V
DCO± to DGND −0.3 V to +2.0 V
OR±A, OR±B to DGND −0.3 V to +2.0 V
PDWNA to DGND −0.3 V to +3.9 V
PDWNB to DGND −0.3 V to +3.9 V
PLLMULTx to DGND −0.3 V to +3.9 V
SDIO to DGND −0.3 V to +3.9 V
CSB to AGND −0.3 V to +3.9 V
SCLK to AGND −0.3 V to +3.9 V
VIN±A, VIN±B to AGND −0.3 V to +2.5 V
CLK+, CLK− to CGND −0.3 V to +2.0 V
Environmental
Storage Temperature Range −65°C to +125°C
Operating Temperature Range −40°C to +85°C
Lead Temperature (Soldering, 10 sec) 300°C
Junction Temperature 150°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
THERMAL RESISTANCE
The exposed paddle must be soldered to the ground plane for
the LFCSP package. Soldering the exposed paddle to the PCB
increases the reliability of the solder joints, maximizing the
thermal capability of the package.
Typical θJA and θJC are specified for a 4-layer board in still air.
Airflow increases heat dissipation, effectively reducing θJA. In
addition, metal in direct contact with the package leads from
metal traces, through holes, ground, and power planes reduces
the θJA.
Table 6. Thermal Resistance
Package Type θJA Unit
64-Lead LFCSP (CP-64-4) 22 °C/W
ESD CAUTION
AD9267
Rev. 0 | Page 8 of 24
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
NOTES
1. DNC = DO NOT CO NNECT.
2. THE EXPOSED PAD MUST BE SOLDERED TO THE GROUND PLANE FOR THE
LFCSP PACKAGE. SOL DERING THE EXPOSED PADDLE TO THE PCB
INCRE ASE S T H E RELI ABILITY O F T HE S OL DE R JOI NTS, M AX IMIZING
THE THERMAL CAPACITY O F T HE PACKAGE.
PIN 1
INDICATOR
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
OR–B
OR+B
DCO–
DCO+
DNC
DNC
DRVDD
DGND
DVDD
DNC
DNC
DNC
DNC
DNC
OR–A
OR+A
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
CLK+
CGND
AGND
AVDD
VIN–B
VIN+B
AVDD
CFILT
VREF
AVDD
VIN–A
VIN+A
AVDD
AGND
RESET
CSB
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
CLK
CVDD
PDWNA
PDWNB
PLL_LOCKED
DVDD
DGND
DRVDD
D0–B
D0+B
D1–B
D1+B
D2–B
D2+B
D3–B
D3+B
SCLK/PLLMULT0
SDIO/PLLMULT1
PLLMULT2
PLLMULT3
PLLMULT4
DVDD
DGND
DRVDD
D3+A
D3–A
D2+A
D2–A
D1+A
D1–A
D0+A
D0–A
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
AD9267
TOP VIEW
(No t t o S cale)
0
7773-003
Figure 3. Pin Configuration
Table 7. Pin Function Descriptions
Pin No. Mnemonic Description
1 CLK− Differential Clock Input (−).
2 CVDD Clock Supply (1.8 V).
3, 4 PDWNA, PDWNB Power-Down Pins. Active high.
5 PLL_LOCKED PLL Lock Indicator.
6, 25, 43 DVDD Digital Supply (1.8 V).
7, 24, 42 DGND Digital Ground.
8, 23, 41 DRVDD Digital Output Driver Supply
9 to 16 D0−B, D0+B to D3−B, D3+B Channel B Differential LVDS Data Output Bits. D0+B is the LSB and D3+B is the MSB.
17, 18 OR−B, OR+B Channel B Overrange Indicator Pins.
19, 20 DCO−, DCO+ Differential Data Clock Output.
21, 22, 26 to 30 DNC Do Not Connect.
31, 32 OR−A, OR+A Channel A Overrange Indicator Pins.
33 to 40 D0−A, D0+A to D3−A, D3+A Channel A Differential LVDS Data Output Bits. D0+A is the LSB and D3+A is the MSB.
44, 45, 46 PLLMULT4, PLLMULT3, PLLMULT2 PLL Mode Selection Pins.
47 SDIO/PLLMULT1 Serial Port Interface Data Input/Output/PLL Mode Selection Pins.
48 SCLK/PLLMULT0 Serial Port Interface Clock/PLL Mode Selection Pins.
49 CSB Serial Port Interface Chip Select Pin Active Low.
50 RESET Chip Reset.
51, 62 AGND Analog Ground.
52, 55, 58, 61 AVDD Analog Supply (1.8 V).
53, 54 VIN+A, VIN−A Channel A Analog Input.
56 VREF Voltage Reference Input.
57 CFILT Noise Limiting Filter Capacitor.
59, 60 VIN+B, VIN−B Channel B Analog Input.
63 CGND Clock Ground.
64 CLK+ Differential Clock Input (+).
65 Exposed paddle (EPAD) Analog Ground. (Pin 65 is the exposed thermal pad on the bottom of the package.) The
exposed paddle must be soldered to analog ground of the PCB to achieve optimal electrical
and thermal performance.
AD9267
Rev. 0 | Page 9 of 24
TYPICAL PERFORMANCE CHARACTERISTICS
All power supplies set to 1.8 V, 640 MHz sample rate, 0.5 V internal reference, PLL disabled, AIN = −2.0 dBFS, TA = 25°C, unless
otherwise noted. The output spectrums shown in Figure 4 through Figure 9 were obtained after 16× decimation at the output of the AD9267
and are shown for a 10 MHz bandwidth.
–140
–130
–120
–110
–100
–90
–80
–70
–60
–50
–40
–30
–20
–10
0
012345678910
FREQ UE NCY (M Hz)
AMPL I T UDE ( d BF S)
07773-004
Figure 4. Single-Tone FFT with fIN = 2.4 MHz
–140
–130
–120
–110
–100
–90
–80
–70
–60
–50
–40
–30
–20
–10
0
012345678910
FREQ UE NCY (M Hz)
AMPL I T UDE ( d BF S)
07773-005
Figure 5. Single-Tone FFT with fIN = 4.2 MHz
–140
–130
–120
–110
–100
–90
–80
–70
–60
–50
–40
–30
–20
–10
0
012345678910
FREQ UE NCY (M Hz)
AMPL I T UDE ( d BF S)
07773-006
Figure 6. Single-Tone FFT with fIN = 8.4 MHz
–140
–130
–120
–110
–100
–90
–80
–70
–60
–50
–40
–30
–20
–10
0
012345678910
FREQUENCY (MHz)
AMPLITUDE (dBFS)
07773-009
Figure 7. Two-Tone FFT with fIN1 = 2.1 MHz, fIN2= 2.4 MHz
–140
–130
–120
–110
–100
–90
–80
–70
–60
–50
–40
–30
–20
–10
0
012345678910
FREQ UE NCY (M Hz)
AMPL I T UDE ( d BF S)
07773-010
Figure 8. Two-Tone FFT with fIN1 = 3.6 MHz, fIN2 = 4.2 MHz
–140
–130
–120
–110
–100
–90
–80
–70
–60
–50
–40
–30
–20
–10
0
012345678910
FREQ UE NCY (M Hz)
AMPL I T UDE ( d BF S)
07773-011
Figure 9. Two-Tone FFT with fIN1 = 7.2 MHz, fIN2 = 8.4 MHz
AD9267
Rev. 0 | Page 10 of 24
07773-042
0 50 100 150 200 250 300
–130
–120
–110
–100
–90
–80
–70
–60
50
FREQUENC Y (M Hz )
AMPL ITUDE ( dBFS )
Figure 10. Noise Transfer Function (NTF)
120
100
80
60
40
20
0
–100 –90 –80 –70 –60 –50 –40 –30 –20 –10 0
SNR/SFDR
INPUT AMPLI T UDE ( dBF S)
07773-007
SFDR
(dBFS)
SFDR
(dBc)
SNR
(dBFS)
SNR
(dB)
Figure 11. Single-Tone SNR and SFDR vs. Input Amplitude with fIN = 2.4 MHz
91
90
89
88
87
86
85
84
83
–60 –40 –20 0 10080604020
SFDR (dBc)
TEMPERATURE (°C)
07773-012
1.9V
1.8V
1.7V
Figure 12. SFDR vs. Temperature
07773-043
FREQ UE NCY (M Hz)
SNR (d B)
0
82.0
82.2
82.4
82.6
82.8
83.0
83.2
83.4
83.6
83.8
84.0
123456789
Figure 13. Single-Tone SNR vs. Input Frequency
07773-044
COMMON-MO DE VOLT AGE ( V)
SNR (d B)
1.70
82.0
82.2
82.4
82.6
82.8
83.0
83.2
83.4
83.6
83.8
84.0
1.75 1.80 1.85 1.90
Figure 14. SNR vs. Input Common-Mode Voltage
–60 –40 –20 0 10080604020
SNR (dB)
TEMPERATURE (°C)
07773-013
1.9V
1.8V
1.7V
83.4
83.2
83.0
82.8
82.6
82.4
82.2
82.0
81.8
Figure 15. SNR vs. Temperature
AD9267
Rev. 0 | Page 11 of 24
07773-046
–120
–110
–100
–90
–80
–70
–60
–50
40
–60 –50 –40 –30 –20 –10
SFDR
INPUT AMPLITUDE (dBFS)
SFDR ( dBFS )
SFDR ( dBc)
Figure 16. Two-Tone SFDR vs. Input Amplitude with
fIN1 = 2.1 MHz, fIN2 = 2.4 MHz
07773-045
–120
–110
–100
–90
–80
–70
–60
–50
40
–60 –50 –40 –30 –20 –10
SFDR
INPUT AMPLITUDE (dBFS)
SFDR (d BFS)
SFDR (dBc)
Figure 17. Two-Tone SFDR vs. Input Amplitude with
fIN1 = 7.2 MHz, fIN2 = 8.4 MHz
07773-047
78
79
80
81
82
83
84
SNR (d B)
PLL DIVI DE RATIO
4.0 4.5 5.0 6.0 7.0 7.5 8.0 8.5 9.010.0
10.5
12.0
12.5
14.0
15.0
16.0
17.0
21.0
2.4MHz
8.4MHz
Figure 18. Single-Tone SNR vs. PLL Divide Ratio with
fIN1 = 2.4 MHz, fIN2 = 8.4 MHz
07773-048
0 8192 16,384 24,576 32,768 40,960 49,152 57,344 65,536
0.5
0
–0.5
–1.0
–1.5
–2.0
–2.5
–3.0
IN L ERROR ( LSB )
OUTPUT CODE
Figure 19. INL with fIN = 2.4 MHz
AD9267
Rev. 0 | Page 12 of 24
EQUIVALENT CIRCUITS
2
V p-p DIFFERENTI
A
L
1.8V CM
500
500
07773-014
Figure 20. Equivalent Analog Input Circuit
CVDD
CLK+
10k10k
90k30k
CVDD
CLK–
07773-015
Figure 21. Equivalent Clock Input Circuit
S
DIO 1k
DRVDD
07773-016
Figure 22. Equivalent SDIO Input Circuit
SCLK 30k
1k
07773-018
Figure 23. Equivalent SCLK Input Circuit
C
SB
A
V
DD
1k
26k
07773-019
Figure 24. Equivalent CSB Input Circuit
DR
V
DD
DGND
D– D+
V
V
V
V
07773-017
NOTES
1. D– AND D+ RE FERS TO
THE D0±x TO D3±x PINS.
Figure 25. Equivalent Digital Output Circuit
10k
2.85k8.5k
3.5k
0.5V
TO CURRENT
GENERATOR
10µF
07773-020
Figure 26. Equivalent VREF Circuit
AD9267
Rev. 0 | Page 13 of 24
THEORY OF OPERATION
The AD9267 uses a continuous time Σ-Δ modulator to convert
the analog input to a digital word. The modulator consists of a
continuous time loop filter preceding a quantizer (see Figure 27),
which samples at fMOD = 640 MSPS. This produces an oversam-
pling ratio (OSR) of 32 for a 10 MHz input bandwidth. The output
of the quantizer is fed back to a DAC that ideally cancels the
input signal. The incomplete input cancellation residue is filtered
by the loop filter and is used to form the next quantizer sample.
H(f)
LOOP FILTER QUANTIZER
+
DAC
ADC
MODULATOR
07773-021
Figure 27. Σ-Δ Modulator Overview
The quantizer produces a nine-level digital word. The quantiza-
tion noise is spread uniformly over the Nyquist band (see
Figure 28) but the feedback loop causes the quantization noise
present in the nine-level output to have a nonuniform spectral
shape. This noise shaping technique (see Figure 29) pushes the
in-band noise out of band; therefore, the amount of quantiza-
tion noise in the frequency band of interest is minimal.
QUANTIZATION NOISE
f
MOD/2
BAND OF INTE RE ST
07773-022
Figure 28. Quantization Noise
NOISE SHAPING
BAND OF I NT ERE ST
f
MOD
/2
0
7773-023
Figure 29. Noise Shaping
ANALOG INPUT CONSIDERATIONS
The continuous time modulator removes the need for an anti-
alias filter at the input to the AD9267. A discrete time converter
aliases signals around the sample clock frequency and its
multiples to the band of interest (see Figure 30). An external
antialias filter is needed to reject these signals.
DESIRED
INPUT UNDESIRED
SIGNAL
ADC
f
S
f
S
/2
07773-024
Figure 30. Discrete Time Converter
In contrast, the continuous time Σ-Δ modulator used within the
AD9267 has inherent antialiasing. The antialiasing property
results from sampling occurring at the output of the loop filter
(see Figure 31), and thus aliasing occurs at the same point in the
loop as quantization noise is injected; aliases are shaped by the
same mechanism as quantization noise. The quantization noise
transfer function, NTF(f), has zeros in the band of interest and
in all alias bands because NTF(f) is a discrete time transfer
function, whereas the loop filter transfer function, LF(f),
introduces poles only in the band of interest because LF(f) is a
continuous time transfer function. The signal transfer function,
being the product of NTF(f) and LF(f), only has zeros in all
alias bands and therefore suppresses all aliases.
LF(f)
H(z)
QUANTIZATION
NOISE
INPUT
OUTPUT
LOOP FILTER
f
MOD
f
MOD
f
MOD
f
NTF(f)
LF(f)
07773-025
Figure 31. Continuous Time Converter
Input Common Mode
The analog inputs of the AD9267 are not internally dc biased.
In ac-coupled applications, the user must provide this bias
externally. Setting the device such that VCM = AVDD is
recommended for optimum performance. The analog inputs
are 500 Ω resistors and the internal reference loop aims to
develop 0.5 V across each input resistor (see Figure 32). With
0 V differential input, the driver sources 1 mA into each
analog input.
TO LOOP FILTER
STAGE 2
DAC
AVDD – 0.5V
500
500
VIN+x
VIN–x
FROM QUANTIZER
7773-026
2.3V
1.8V
1.3V
2
.3V
1.8V
1.3V
Figure 32. Input Common Mode
AD9267
Rev. 0 | Page 14 of 24
Differential Input Configurations
Optimum performance can be achieved by driving the AD9267
in a differential input configuration. The ADA4937-2 differential
driver provides excellent performance and a flexible interface to
the ADC. The output common-mode voltage of the ADA4937-2 is
easily set by connecting AVDD to the VOCMx pin of the ADA4937-2
(see Figure 33). The noise and linearity of the ADA4937-2 needs
important consideration because the system performance may
be limited by the ADA4937-2.
11
6
7
13
12
9
15
200
200
200
60.449.9
50
SIGNAL
SOURCE
2V p-p
R
T
60.4
V
S
VIN–x
VIN+x
0.1µF
0.1µF
0.1µF
+5
V
–5V
ADA4937-2
V
OCM2
07773-027
AD9267
0.1µF
AVDD
+1.8V
Figure 33. Differential Input Configuration Using the ADA4937-2
For frequencies offset from dc, where SNR is a key parameter,
differential transformer coupling is the recommended input
configuration. An example is shown in Figure 34. The center
tap of the secondary winding of the transformer is connected to
AVDD to bias the analog input.
The signal characteristics must be considered when selecting a
transformer. Most RF transformers saturate at frequencies
below a couple of megahertz (MHz), and excessive signal power
can cause core saturation, which leads to distortion.
50
SIGNAL
SOURCE
2V p-p 1:1
R
T
50
V
S
VIN–x
VIN+x
0.1µF
AVDD
AD9267
07773-028
Figure 34. Differential Transformer Configuration
Voltage Reference
A stable and accurate 0.5 V voltage reference is built into the
AD9267. The reference voltage should be decoupled to minim-
ize the noise bandwidth using a 10 F capacitor. The reference
is used to generate a bias current into a matched resistor such
that when used to bias the current in the feedback DAC, a
voltage of AVDD − 0.5 V is developed at the internal side of the
input resistors (see Figure 35). The current bias circuit should
also be decoupled on the CFILT pin with a 10 µF capacitor. For
this reason, the VREF voltage should always be 0.5 V.
AVDD
AVDD – 0. 5V
CFILT
A
V
DD – 0.5V
500
TO LOOP
FILTER
STAGE 2
500
VIN+x
V
CM
=AVDD
VIN p-p = 2V
VIN–x 500
10k
10µF
0.5V
VREF
10µF
REF
0
7773-029
Figure 35. Voltage Reference Loop
Internal Reference Connection
To minimize thermal noise, the internal reference on the AD9267
is an unbuffered 0.5 V. It has an internal 10 kΩ series resistor,
which, when externally decoupled with a 10 µF capacitor, limits
the noise (see Figure 36). Do not use the unbuffered reference
to drive any external circuitry. The internal reference is used by
default and when Serial Register 0x18[6] is reset.
10k
2.85k8.5k
3.5k
0.5V
TO CURRENT
GENERATOR
10µF
07773-030
Figure 36. Internal Reference Configuration
External Reference Operation
If an external reference is desired, the internal reference can be
disabled by setting Serial Register 0x18[6] high. Figure 37 shows
an application using the ADR130B as a stable external reference.
0.5
V
ADR130B
TO CURRENT
GENERATOR
0.1µF 10µF
AVDD 10k
07773-031
Figure 37. External Reference Configuration
CLOCK INPUT CONSIDERATIONS
The AD9267 offers two modes of sourcing the ADC sample
clock (CLK+ and CLK−). The first mode uses an on-chip clock
multiplier that accepts a reference clock operating at the lower
input frequency. The on-chip phase-locked loop (PLL) then
multiplies the reference clock up to a higher frequency, which is
then used to generate all the internal clocks required by the Σ-
modulator.
The clock multiplier provides a high quality clock that meets
the performance requirements of most applications. Using the
on-chip clock multiplier removes the burden of generating and
distributing the high speed clock.
AD9267
Rev. 0 | Page 15 of 24
The second mode bypasses the clock multiplier circuitry and
allows the clock to be directly sourced. This mode enables the
user to source a very high quality clock directly to the Σ-Δ
modulator. Sourcing the clock directly may be necessary in
demanding applications that require the lowest possible output
noise. Refer to Figure 18, which shows the degradation in SNR
performance for the various PLL settings.
In either case, when using the on-chip clock multiplier or
sourcing the high speed clock directly, it is necessary that the
clock source have low jitter to maximize the Σ-Δ modulator
noise performance. High speed, high resolution ADCs and
modulators are sensitive to the quality of the clock input. As
jitter increases, the SNR performance of the AD9267 degrades
from that specified in Table 2. The jitter inherent to the part due
to the PLL root sum squares with any external clock jitter,
thereby degrading performance. To prevent jitter from dominating
the performance of the AD9267, the input clock source should be
no greater than 1 ps rms of jitter.
The CLK± inputs are self-biased to 450 mV (see Figure 21); if
dc-coupled, it is important to maintain the specified 450 mV
input common-mode voltage. Each input pin can safely swing
from 200 mV p-p to 1 V p-p single-ended about the 450 mV
common-mode voltage. The recommended clock inputs are
CMOS or LVPECL.
The specified clock rate of the Σ-Δ modulator, fMOD, is 640 MHz.
The clock rate possesses a direct relationship with the available
input bandwidth of the ADC.
Bandwidth = fMOD ÷ 64
In either case, using the on-chip clock multiplier to generate the
Σ-Δ modulator clock rate or directly sourcing the clock, any
deviation from 640 MHz results in a change in input bandwidth.
The input range of the clock is limited to 640 MHz ± 5%.
Direct Clocking
The default configuration of the AD9267 is for direct clocking
where the PLL is bypassed. Figure 38 shows one preferred
method for clocking the AD9267. A low jitter clock source is
converted from a single-ended signal to a differential signal
using an RF transformer. The back-to-back Schottky diodes
across the secondary side of the transformer limits clock
excursions into the AD9267 to approximately 0.8 V p-p differen-
tial. This helps prevent the large voltage swings of the clock
from feeding through to other portions of the AD9267 while
preserving the fast rise and fall times of the signal, which are
critical to achieving low jitter.
CLOCK
INPUT XFMR
MINI-CIRCUITS
TC1- 1- 1 3M + , 1: 1
SCHOTTKY
DIODES:
HSM2812
50
CLK+
CLK–
0.1µF
0.1µF
ADC
AD9267
0.1µF
0.1µF
0
7773-053
Figure 38. Transformer-Coupled Differential Clock
If a differential clock is not available, the AD9267 can be driven
by a single-ended signal into the CLK+ terminal with the CLK−
terminal ac-coupled to ground. Figure 39 shows the circuit
configuration.
SCHOTTKY
DIODES:
HSM2812
50
CLK+
CLK–
0.1µF
0.1µF
ADC
AD9267
CLOCK
INPUT
0
7773-054
Figure 39. Single-Ended Clock
Another option is to ac couple a differential LVPECL signal to
the sample clock input pins, as shown in Figure 40. The AD951x
family of clock drivers is recommended because it offers excellent
jitter performance.
100
240240
50
1
1
50 RESISTO RS ARE OPTI ONAL .
50
1
CLK+
CLK–
0.1µF
0.1µF
ADC
AD9267
CLOCK
INPUT
CLOCK
INPUT
0.1µF
0.1µF
CLK
AD951x
LVPECL
DRIVER
CLK
07773-055
Figure 40. Differential LVPECL Sample Clock
Internal PLL Clock Distribution
The alternative clocking option available on the AD9267 is to
apply a low frequency reference clock and use the on-chip clock
multiplier to generate the high frequency fMOD rate. The internal
clock architecture is shown in Figure 41.
PHASE
DETECTOR
DIVIDER
PLLMULT
0x0A[5:0]
CLK±
MODULATOR
CLOCK
640MSPS
PLLENABLE
0x09[2]
÷N
LOOP
FILTER VCO
PLL
÷2
07773-040
Figure 41. Internal Clock Architecture
The clock multiplication circuit operates such that the VCO
outputs a frequency, fVCO, equal to the reference clock input
multiplied by N
fVCO = (CLK±) × (N)
where N is the PLL multiplication (PLLMULT) factor.
The Σ-Δ modulator clock frequency, fMOD, is equal to
fMOD = fVCO ÷ 2
AD9267
Rev. 0 | Page 16 of 24
The reference clock, CLK±, is limited to 30 MHz to 160 MHz
when configured to use the on-chip clock multiplier. Given the
input range of the reference clock and the available multiplica-
tion factors, the fVCO is approximately 1280 MHz. This results in
the desired fMOD rate of 640 MHz with a 50% duty cycle.
The PLL of the AD9267 can be controlled through either the serial
port interface or the PLLMULTx pins. For serial port interface
control, Register 0x09 and Register 0x0A are used. Before the
PLL enable register bit (PLLENABLE) is set, the PLL multiplica-
tion factor should be programmed into Register 0x0A[5:0].
After setting the PLLENABLE bit, the PLL locks and reports a
locked state in Register 0x0A[7]. If the PLL multiplication factor
is changed, the PLL enable bit should be reset and set again.
Some common clock multiplication factors are shown in Table 8.
The recommended sequence for enabling and programming the
on-chip clock multiplier is as follows:
1. Apply a reference clock to the CLK± pins.
2. Program the PLL multiplication factor in
Register 0x0A[5:0]. See Table 8.
3. Enable the PLL; Register 0x09 = 04 (decimal).
External PLL Control
At power-up, the serial interface is disabled until the first serial
port access. If the serial interface is disabled, the PLLMULTx
pins control the PLL multiplication factor. The five PLLMULTx
pins (Pin 44 to Pin 48) offer all the available multiplication
factors. If all PLLMULTx pins are tied high, the PLL is disabled
and the AD9267 assumes the high frequency modulator clock
rate that is applied to the CLK± pins. Table 10 shows the relation-
ship between PLLMULTx pins and the PLL multiplication factor.
PLL Autoband Select
The PLL VCO has a wide operating range that is covered by
overlapping frequency bands. For any desired VCO output fre-
quency, there are multiple valid PLL band select values. The
AD9267 possesses an automatic PLL band select feature on chip
that determines the optimal PLL band setting. This feature can
be enabled by writing to Register 0x0A[6] and is the recom-
mended configuration with the PLL clocking option.
Table 8. PLL Multiplication Factors
0x0A[5:0] PLLMULT (N) 0x0A[5:0] PLLMULT (N)
1 8 33 32
2 8 34 34
3 8 35 34
4 8 36 34
5 8 37 34
6 8 38 34
7 8 39 34
8 8 40 34
9 9 41 34
10 10 42 42
11 10 43 42
12 12 44 42
13 12 45 42
14 14 46 42
15 15 47 42
16 16 48 42
17 17 49 42
18 18 50 42
19 18 51 42
20 20 52 42
21 21 53 42
22 21 54 42
23 21 55 42
24 24 56 42
25 25 57 42
26 25 58 42
27 25 59 42
28 28 60 42
29 28 61 42
30 30 62 42
31 30 63 42
32 32 64 42
Table 9. Common Modulator Clock Multiplication Factors
CLK±
(MHz)
0x0A[5:0]
(PLLMULT)
fVCO
(MHz)
fMOD
(MHz)
BW
(MHz)
30.72 42 1290.24 645.12 10.08
39.3216 32 1258.29 629.15 9.83
52.00 25 1300.00 650.00 10.16
61.44 21 1290.24 645.12 10.08
76.80 17 1305.60 652.80 10.20
78.00 17 1326.00 663.00 10.36
78.6432 16 1258.29 629.15 9.83
89.60 15 1344.00 672.00 10.50
92.16 14 1290.24 645.12 10.08
122.88 10 1228.80 614.40 9.60
134.40 10 1344.00 672.00 10.50
153.60 8 1228.80 614.40 9.60
157.2864 8 1258.29 629.15 9.83
AD9267
Rev. 0 | Page 17 of 24
Table 10. PLLMULTx Pins and PLL Multiplication Factor
PLLMULT[4:0] Pins PLL Multiplication Factors (N)
0 8
1 9
2 10
3 12
4 14
5 15
6 16
7 17
8 18
9 20
10 21
11 24
12 25
13 28
14 30
15 32
16 34
17 to 30 42
31 Direct clocking
POWER DISSIPATION AND STANDBY MODE
The AD9267 consumes 415 mW. This power consumption can
be further reduced by configuring the chip in channel power-
down, standby, or sleep mode. The low power modes turn off
internal blocks of the chip including the reference. As a result,
the wake-up time is dependent on the amount of circuitry that
is turned off. Fewer internal circuits powered down result in
proportionally shorter wake-up time. The different low power
modes are shown in Table 11. In the standby mode, all clock
related activity is disabled in addition to each channel; the
references and LVDS outputs remain powered up to ensure a
short recovery and link integrity, respectively. During sleep
mode, all internal circuits are powered down, putting the device
into its lowest power mode; the LVDS outputs are disabled.
Each ADC channel can be independently powered down or
both channels can be set simultaneously by writing to the
channel index, Register 0x05[1:0]. Additionally, if the serial
port interface is not available, each channel can be indepen-
dently configured by tying the PDWNA (Pin 3) or PDWNB
(Pin 4) high.
Table 11. Low Power Modes
Mode 0x08[1:0]
Analog
Circuitry Clock Ref.
Normal 0x0 On On On
Channel Power-Down 0x1 Off On On
Standby 0x2 Off Off On
Sleep 0x3 Off Off Off
DIGITAL OUTPUTS
Digital Output Format
The AD9267 digital bus outputs twos complement, single data
rate, LVDS data at 640 MSPS. The output is four bits wide per
channel.
The AD9267 supports both the ANSI-644 and a reduced power
data format similar to the IEEE1596.3 standard. The default
configuration at power-up is ANSI-644. This can be changed to
a low power reduced signal option by addressing Register
0x14[7], DRVSTD.
The LVDS driver current is derived on chip and sets the output
current at each output equal to a nominal 3.5 mA for the ANSI-
644 standard. A 100 Ω differential termination resistor placed at
the LVDS receiver inputs result in a nominal 350 mV swing at
the receiver. In the reduced power data format, the output swing
is limited to 200 mV and the resulting output current into the
100 Ω termination is 2 mA. As a result of the reduced LVDS
voltage swing, an additional 25% digital power savings can be
achieved over the ANSI-644 standard.
The desired output format can be selected by addressing
Register 0x14[7], DRVSTD. The LVDSTERM bits, Register
0x15[5:4], provide either 100 Ω or 200 Ω, or no termination
at the output of the data bus. Selecting the appropriate termina-
tion resistor is important to allow maximum signal transfer and
to minimize reflections for signal integrity. This can be achieved
by selecting a termination resistor that impedance matches the
termination of the receiver.
Overrange (OR) Condition
An overrange condition can be triggered by large in-band signals
that exceed the full-scale range of the Σ-Δ modulator, or it
can be triggered by out-of-band signals gained by the transfer
characteristics of the modulator. Figure 43 shows the signal
transfer function of the Σ-Δ modulator. The modulator output
possesses out-of-band gain above 10 MHz. As a result, the input
signal may exceed full scale for input frequencies beyond 10 MHz
and the ADC may be in an overrange state. The OR±x pins
serve as indicators for the overrange condition.
The OR±x pins are synchronous outputs that are updated at the
output data rate. The pins indicate whether an overrange condi-
tion has occurred within the AD9267. Ideally, OR±x should be
latched on the falling edge of DCO± to ensure proper setup-and-
hold time. However, because an overrange condition typically
extends well beyond one clock cycle (that is, does not toggle at
the DCO± rate); data can usually be successfully detected on
the rising edge of DCO± or monitored asynchronously. The
user has the ability to select how the overrange condition is
reported and this is controlled through the SPI bits (AUTORST,
OR_IND1, and OR_IND2) in Register 0x111[7:5]. The two
modes of operation are normal and data valid mode.
AD9267
Rev. 0 | Page 18 of 24
In normal operation mode, the analog input can toggle the
OR±x pin for a number of clock cycles as it approaches full
scale. The OR±x pin is a pulse-width modulated (PWM) signal;
therefore, as the analog input increases in amplitude, the
duration of OR±x pin toggling increases. Eventually, when the
OR±x pin is high for an extended period of time, the ADC
overloads; thus, there is little correspondence between analog
input and digital output. In this mode, the duration of the
OR±x pin can be used as a coarse indicator to the signal
amplitude at the input of the ADC. In data valid mode, the
OR±x pin remains high when there are no memory access
operations taking place, such as internal calibration or factory
memory transfer, and the inputs of the ADC are within the
operating range.
In either modes of operation, the AUTORST bit can be enabled
and this automatically resets the modulator in an overload
condition. Because the OR±x signal is a PWM signal and the
toggling of OR±x does not always indicate an overload
condition, the modulator only resets after 16 consecutive clock
cycles where OR±x remains high or if the loop filter becomes
saturated. The OR±x pin remains high until the automatic reset
has completed.
If the AD9267 is used in a system that incorporates automatic
gain control (AGC), the OR±x signals can be used to indicate
that the signal amplitude should be reduced. This may be
particularly effective for use in maximizing the signal dynamic
range if the signal includes high occurrence components that
occasionally exceed full scale by a small amount.
TIMING
The AD9267 provides latched data outputs with a latency of
seven clock cycles. The AD9267 also provides a data clock
output (DCO±) pin intended to assist in capturing the data in
an external register. The data outputs are valid on the rising
edge of DCO±, unless changed by setting Serial Register 0x16[7]
(see the Serial Port Interface (SPI) section). See Figure 2 for a
graphical timing description.
Table 12. OR±x Conditions
Reset State AUTORST OR_IND1 OR_IND2 Function
Normal Reset Off 0 0 0 If overrange: OR±x = 1, else OR±x = 0
Data Valid Reset Off 0 1 1 If memory access: OR±x = 0, else OR±x = 1
Normal Reset On 1 0 0 If overrange or reset: OR±x = 1, else OR±x = 0
Data Valid Reset On 1 1 1 If memory access, or reset: OR±x = 0, else OR±x = 1
AD9267
Rev. 0 | Page 19 of 24
SERIAL PORT INTERFACE (SPI)
The AD9267 serial port interface (SPI) allows the user to
configure the converter for specific functions or operations
through a structured register space provided inside the ADC.
This provides the user added flexibility and customization
depending on the application. Addresses are accessed via the
serial port and can be written to or read from via the port.
Memory is organized into bytes that are further divided into
fields, as documented in the Memory Map section. For detailed
operational information, see the see the AN-877 Application
Note, Interfacing to High Speed ADCs via SPI.
CONFIGURATION USING THE SPI
As summarized in Table 13, three pins define the SPI of this
ADC. The SCLK pin synchronizes the read and write data
presented to the ADC. The SDIO pin allows data to be sent and
read from the internal ADC memory map registers. The CSB
pin is an active low control that enables or disables the read and
write cycles.
Table 13. Serial Port Interface Pins
Pin Function
SCLK SCLK (serial clock) is the serial shift clock. SCLK
synchronizes serial interface reads and writes.
SDIO SDIO (serial data input/output) is an input and output
depending on the instruction being sent and the
relative position in the timing frame.
CSB CSB (chip select) is an active low control that gates the
read and write cycles.
The falling edge of CSB in conjunction with the rising edge of
the SCLK determines the start of the framing. Figure 42 and
Table 14 provide an example of the serial timing and its
definitions.
Other modes involving CSB are available. CSB can be held low
indefinitely to permanently enable the device (this is called
streaming). CSB can stall high between bytes to allow for
additional external timing. When CSB is tied high, SPI
functions are placed in a high impedance mode.
During an instruction phase, a 16-bit instruction is transmitted.
Data follows the instruction phase and the length is determined
by the W0 bit and the W1 bit. All data is composed of 8-bit words.
The first bit of each individual byte of serial data indicates whether
a read or write command is issued. This allows the serial data
input/output (SDIO) pin to change direction from an input to
an output.
In addition to word length, the instruction phase determines if
the serial frame is a read or write operation, allowing the serial
port to be used to both program the chip as well as to read the
contents of the on-chip memory. If the instruction is a readback
operation, performing a readback causes the serial data input/
output (SDIO) pin to change direction from an input to an
output at the appropriate point in the serial frame.
Data can be sent in MSB- or in LSB-first mode. MSB first is
the default setting on power-up and can be changed via the
configuration register. For more information, see the AN-877
Application Note, Interfacing to High Speed ADCs via SPI.
Table 14. SPI Timing Diagram Specifications
Parameter Definition
tSDS Setup time between data and rising edge of SCLK
tSDH Hold time between data and rising edge of SCLK
tSCLK Period of the clock
tSS Setup time between CSB and SCLK
tSH Hold time between CSB and SCLK
tSHIGH Minimum period that SCLK should be in a logic
high state
tSLOW Minimum period that SCLK should be in a logic
low state
DON’T CARE
DON’T CAREDON’T CARE
DON’T CARE
SDIO
SCLK
CSB
t
SS
t
SDH
t
SHIGH
t
SCLK
t
SLOW
t
SDS
t
SH
R/W W1 W0 A12 A11 A10 A9 A8 A7 D5 D4 D3 D2 D1 D0
07773-036
Figure 42. Serial Port Interface Timing Diagram
AD9267
Rev. 0 | Page 20 of 24
HARDWARE INTERFACE
The pins described in Table 13 comprise the physical interface
between the programming device of the user and the serial port
of the AD9267. The SCLK and CSB pins function as inputs
when using the SPI interface. The SDIO pin is bidirectional,
functioning as an input during write phases and as an output
during readback.
The SPI interface is flexible enough to be controlled by either
PROM or PIC microcontrollers. This provides the user with the
ability to use an alternate method to program the ADC. One
such method is described in detail in the AN-812 Application
Note, MicroController-Based Serial Port Interface (SPI) Boot
Circuit.
When the SPI interface is not used, SCLK/PLLMULT0 and
SDIO/PLLMULT1 serve a dual function. When strapped to
AVDD or ground during device power-on, the pins are
associated with a specific function.
AD9267
Rev. 0 | Page 21 of 24
APPLICATIONS INFORMATION
FILTERING REQUIREMENT
The need for anti-alias protection often requires one or two
octaves for a transition band, which reduces the usable
bandwidth of a Nyquist converter to between 25% and 50% of
the available bandwidth. A CT Σ-Δ converter maximizes the
available signal bandwidth by forgoing the need for an
antialiasing filter because the architecture possesses inherent
antialiasing. Although a high order, sharp cutoff antialiasing
filter may not be necessary because of the unique characteristics
of the architecture, a low order filter may still be required to
precede the ADC for out-of-band signal handling.
Depending on the application and the system architecture, this
low order filter may or may not be necessary. The signal
transfer function (STF) of a continuous time feedforward ADC
usually contains out-of-band peaks. Because these STF peaks
are typically one or two octaves above the pass-band edge, they
are not problematic in applications where the bulk of the signal
energy is in or near the pass band. However, in applications
with large far-out interferers, it is necessary to either add a filter
to attenuate these problematic signals or to allocate some of the
ADC dynamic range to accommodate them.
Figure 43 shows the normalized STF of the AD9267 CT Σ-Δ
converter. The figure shows out-of-band peaking beyond the
band edge of the ADC. Within the 10 MHz band of interest, the
STF is maximally flat with less than 0.1 dB of gain. Maximum
peaking occurs at 60 MHz with 10 dB of gain. To put this into
perspective, for a fixed input power, a 5 MHz in-band-signal
appears at −5 dBFS, a 25 MHz tone appears at2 dBFS and
60 MHz tone at +5 dBFS. Because the maximum input to the
ADC is −2 dBFS, large out-of-band signals can quickly saturate
the system. This implies that under these conditions, the digital
outputs of the ADC no longer accurately represents the input.
Refer to the Overrange (OR) Condition section for details on
overrange detection and recovery.
15
13
11
9
7
5
3
1
–1
–3
–5 0 102030405060708090100
FREQ UE NCY (MHz)
GAIN (dB)
07773-049
Figure 43. STF
Figure 43 shows the gain profile of the AD9267 and this can be
interpreted as the level in which the signal power should be
scaled back to prevent an overload condition. This is the
ultimate trip point and before this point is reached, the in-band
noise (IBN) slowly degrades. As a result, it is recommended that
the low-pass filter be designed to match the profile of Figure 44,
which shows the maximum input signal for a 3 dB degradation
of in-band noise. The input signal is attenuated to allow only
3 dB of noise degradation over frequency.
The noise performance is normalized to a −2 dBFS in-band
signal. The AD9267 STF and NTF are flat within the band of
interest and should result in almost no change in input level and
IBN. Beyond the bandwidth of the AD9267, out-of-band
peaking adds gain to the system, therefore requiring the input
power to be scaled back to prevent in-band noise degradation.
The input power is scaled back to a point where only 3 dB of
noise degradation is allowed, therefore resulting in Figure 44.
5
0
–5
–10
–15
–20
–25 0 102030405060708090100
FREQ UE NC Y (MHz )
AMPL ITUDE ( dB)
CHEBYSHEV II
FI L TER RESPO NSE
–40°C
+85°C +25°C
07773-051
Figure 44. Maximum Input Level for 3 dB Noise Degradation
An example third-order low-pass Chebyshev II type filter is
shown in Figure 45 and the corresponding magnitude vs.
frequency response of the filter is shown in Figure 44.
07773-052
L1
180nH
L1
180nH
C2
390pF
C2
390pF
C3
220pF
C1
39pF 1k
AD9267
CT Σ-Δ
VIN+
VIN–
Figure 45. Third-Order Low-Pass Chebyshev II Filter
AD9267
Rev. 0 | Page 22 of 24
Referring to Figure 46, the 3 dB cutoff frequency of the low-
pass Chebyshev II filter response resides at 15.75 MHz, and at
10 MHz, there is 0.43 dB of attenuation due to the sharp roll-off
of the filter. Table 15 summarizes the components and
manufacturers used to build the circuit.
Table 15. Chebyshev II Filter Components
Parameter Value Unit Manufacturer
C1 39 pF Murata GRM188 series, 0603
L1 180 nH Coil Craft 0402AF, 2%
C2 390 pF Murata GRM188 series, 0603
C3 220 pF Murata GRM188 series, 0603
–20 0 2 4 6 8 101214161820
–18
–16
–14
–12
–10
–8
–6
–4
–2
0
–60
–50
–40
–30
–20
–10
0
10
20
30
40
GROUP DELAY (ns)
FREQ UE NC Y (MHz )
AMPL ITUDE ( dB)
07773-050
Figure 46. Low-Pass Chebyshev II Filter Response
In addition to matching the profile of Figure 44, group delay
and channel matching are important filter design criteria. Low
tolerance components are highly recommended for improved
channel matching, which translates to minimal degradation in
image rejection for quadrature systems.
AD9267
Rev. 0 | Page 23 of 24
MEMORY MAP
Table 16. Memory Map
Register Address (Hex) Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
SPI Port Config 00 0 LSBFIRST SOFTRESET 1 1 SOFTRESET LSBFIRST 0
Chip ID 01 CHIPID[7:0]
Chip Grade 02 CHILDID[1:0]
Channel Index 05 Channel[1:0]
Power Modes 08 PWRDWN[1:0]
PLLENABLE 09 PLLENABLE
PLL 0A PLLLOCKED PLLAUTO PLLMULT[5:0]
Output Modes 14 DRVSTD OUTENB
Output Adjust 15 LVDSTERM[1:0]
Output Clock 16 DCOINV
Reference 18 EXTREF
Overrange 111 AUTORST OR_IND1 OR_IND2
MEMORY MAP DEFINITIONS
Table 17. Memory Map Definitions
Register Address Bit Name Bit(s) Default Description
SPI Port Config 0x00 LSBFIRST [6], [1] 0 0: serial interface uses MSB-first format
1: serial interface uses LSB-first format
SOFTRESET [5], [2] 0 1: default all serial registers except 0x00, 0x09, and 0x0A
Chip ID 0x01 CHIPID [7:0] 0x22 0x22: AD9267
Chip Grade 0x02 CHILDID 5:4] 0 0x00: 10 MHz bandwidth
0x10: 5 MHz bandwidth
0x20: 2.5 MHz bandwidth
0x30: modulator only
Channel Index 0x05 Channel [1:0] 0 0x1: Channel A only addressed
0x2: Channel B only addressed
0x3: both channels addressed simultaneously
Power Modes 0x08 PWRDWN [1:0] 0 0x0: normal operation
0x1: channel power-down (local)
0x2: standby (everything except reference circuits)
0x3: sleep
PLLENABLE 0x09 PLLENABLE [2] 0 1: enable PLL
PLL 0x0A PLLLOCKED [7] 0 0: PLL is not locked
1: PLL is locked
PLLAUTO [6] 0 0: disable PLL auto band select
1: enable PLL auto band select
PLLMULT [5:0] 0 See Table 8
Output Modes 0x14 DRVSTD [7] 0 0: ANSI-644
1: Low power (IEEE1596.3 similar)
OUTENB [4] 0 1: Channel A and Channel B outputs tristated
Output Adjust 0x15 LVDSTERM [5:4] 0 0: no termination
1: 200 Ω
2: 100 Ω
3: 100 Ω
Output Clock 0x16 DCOINV [7] 0 1: invert DCO±
Reference 0x18 EXTREF [6] 0 1: use external reference
Overrange 0x111 AUTORST [7] 0 1: enable autoreset
OR_IND1 [6] 0 See Table 12
OR_IND2 [5] 0 See Table 12
AD9267
Rev. 0 | Page 24 of 24
OUTLINE DIMENSIONS
COMP L I ANT T O JEDEC STANDARDS MO -220-V M MD-4
091707-C
6.35
6.20 SQ
6.05
0.25 M IN
TOP VIEW 8.75
BSC SQ
9.00
BSC SQ
1
64
16
17
49
48
32
33
0.50
0.40
0.30
0.50
BSC
0.20 RE F
12° M AX 0.80 M A X
0.65 TYP
1.00
0.85
0.80
7.50
REF
0.05 M A X
0.02 NOM
0.60 M A X
0.60
MAX
EXPOSED PAD
(BO T TOM VIEW )
SEATING
PLANE
PIN 1
INDICATOR
PIN 1
INDICATOR
0.30
0.23
0.18
FO R P ROPER CONNECT ION OF
THE EXPOSED PAD, REFER TO
THE P IN CONFIGURATIO N AND
FUNCT I O N DES CRIP T I O NS
SECTION OF THIS DATA SHEET.
Figure 47. 64-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
9 mm × 9 mm Body, Very Thin Quad
Dimensions shown in millimeters
ORDERING GUIDE
Model Temperature Range Package Description Package Option
AD9267BCPZ1 −40°C to +85°C 64-Lead Lead Frame Chip Scale Package (LFCSP_VQ) CP-64-4
AD9267EBZ1 Evaluation Board
1 Z = RoHs Compliant Part.
©2009 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D07773-0-7/09(0)