CS48DV2B Data Sheet FEATURES World's most cost-effective 32-bit DSP featuring Dolby(R) Volume and Audistry(R) by Dolby -- -- Supports native processing at input Fs up to 48kHz Single download image enables support for 32 KHz, 44.1 kHz, and 48 kHz audio input The new CS48DV2B supports a host of signal processing applications concurrently, including the mass production-ready Dolby Volume solution. See Section 3. for details about firmware concurrency on the CS48DV2B. The target applications for the CS48DV2B DSP are: CS48DV2B supports up to 2.0 channels of audio input and up to 2.1 channels of output Volume including Tone Control, Multiband Parametric EQ, Bass Management, Delays. Configurable Serial Audio Inputs/Outputs -- Configurable for all input/output digital audio types (I2S/LJ/RJ) -- 32-bit data path delivers uncompromised dynamic range -- 192 kHz capable integrated S/PDIF transmitter -- DAO can operate in master or slave mode (SCLK & LRCLK) Integrated Clock Manager/PLL -- -- -- -- PMD/iPod(R) Docking Stations Automotive Head Units Automotive Outboard Amplifiers -- Blu-ray Disc(R) & DVD Receivers / HTiBs -- PC Speakers All of these applications and many more that use volume control and are subject to playback from sources that do not have consistent volume levels will benefit from the CS48DV2B Dolby Volume solution. Capable of operating from a wide variety of external crystals or external oscillators Slave Host Boot Capability via Serial Interface -- Digital Televisions Soundbars / DTVs with Integrated Soundbars EN D TI A EL L PH D R I A FT Enables concurrent processing features beyond Dolby -- -- SPITM interface capable of running up to 25 MHz during run time Ordering Information: See page 21 for ordering information. 1.8V Core and 3.3V I/O that is tolerant to 5V input Low-power Mode enabled Energy Star(R) Design Compliance Capability via lowpower mode, 268 W in Standby mode O S/PDIF Serial Control 1 GPIO Debug Watchdog N 2.0 Ch. Audio In FI D -- D M A 32-bit DSP P X TMR1 TMR2 Y C Up to 2.1 Ch Audio Out http://www.cirrus.com PLL Copyright 2009 Cirrus Logic CONFIDENTIAL FEB '09 DS875F2 EN D TI EL A L PH D I RA FT CS48DV2B Data Sheet 32-bit Audio DSP for Dedicated Dolby Volume and Audistry by Dolby Contacting Cirrus Logic Support For all product questions and inquiries contact a Cirrus Logic Sales Representative. To find the one nearest to you go to www.cirrus.com. IMPORTANT NOTICE D Cirrus Logic, Inc. and its subsidiaries ("Cirrus") believe that the information contained in this document is accurate and reliable. However, the information is subject to change without notice and is provided "AS IS" without warranty of any kind (express or implied). Customers are advised to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, indemnification, and limitation of liability. No responsibility is assumed by Cirrus for the use of this information, including use of this information as the basis for manufacture or sale of any items, or for infringement of patents or other rights of third parties. This document is the property of Cirrus and by furnishing this information, Cirrus grants no license, express or implied under any patents, mask work rights, copyrights, trademarks, trade secrets or other intellectual property rights. Cirrus owns the copyrights associated with the information contained herein and gives consent for copies to be made of the information only for use within your organization with respect to Cirrus integrated circuits or other products of Cirrus. This consent does not extend to other copying such as copying for general distribution, advertising or promotional purposes, or for creating any work for resale. N FI CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE ("CRITICAL APPLICATIONS"). CIRRUS PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE IN PRODUCTS SURGICALLY IMPLANTED INTO THE BODY, AUTOMOTIVE SAFETY OR SECURITY DEVICES, LIFE SUPPORT PRODUCTS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF CIRRUS PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK AND CIRRUS DISCLAIMS AND MAKES NO WARRANTY, EXPRESS, STATUTORY OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, WITH REGARD TO ANY CIRRUS PRODUCT THAT IS USED IN SUCH A MANNER. IF THE CUSTOMER OR CUSTOMER'S CUSTOMER USES OR PERMITS THE USE OF CIRRUS PRODUCTS IN CRITICAL APPLICATIONS, CUSTOMER AGREES, BY SUCH USE, TO FULLY INDEMNIFY CIRRUS, ITS OFFICERS, DIRECTORS, EMPLOYEES, DISTRIBUTORS AND OTHER AGENTS FROM ANY AND ALL LIABILITY, INCLUDING ATTORNEYS' FEES AND COSTS, THAT MAY RESULT FROM OR ARISE IN CONNECTION WITH THESE USES. O Cirrus Logic, Cirrus, the Cirrus Logic logo designs, DSP Composer is a trademarks of Cirrus Logic, Inc. All other brand and product names in this document may be trademarks or service marks of their respective owners. C Dolby, Audistry, and the sound shell logo are registered trademarks of Dolby Laboratories. Supply of an implementation of Dolby Technology does not convey a license nor imply a right under any patent, or any other industrial or Intellectual Property Right of Dolby Laboratories, to use the Implementation in any finished end-user or ready-to-use final product. It is hereby notified that a license for such use is required from Dolby Laboratories. SPI is a trademark of Motorola, Inc. I2C is a registered trademark of Philips Semiconductor. iPod is a registered trademark of Apple Computer, Inc. Blu-ray Disc is a registered trademark of SONY KABUSHIKI KAISHA CORPORATION. Energy Star is a registered trademark of the Environmental Protection Agency, a federal agency of the United States government. 2 Copyright 2009 Cirrus Logic CONFIDENTIAL DS875F2 CS48DV2B Data Sheet 32-bit Audio DSP for Dedicated Dolby Volume and Audistry by Dolby Table of Contents 1. Documentation Strategy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.1 Licensing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3. Code Overlays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 4. Hardware Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 EN D TI EL A L PH D I RA FT 4.1 DSP Core . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1.1 DSP Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1.2 DMA Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2 On-chip DSP Peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2.1 Digital Audio Input Port (DAI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2.2 Digital Audio Output Port (DAO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2.3 Serial Control Port (I2C(R) or SPITM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2.4 GPIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2.5 PLL-based Clock Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2.6 Hardware Watchdog Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3 DSP I/O Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3.1 Multiplexed Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3.2 Termination Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3.3 Pads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4 Application Code Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 7 7 8 8 8 8 8 8 9 9 9 9 9 9 5. Characteristics and Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 FI D 5.1 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 5.2 Recommended Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 5.3 Digital DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 5.4 Power Supply Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 5.5 Thermal Data (48-Pin LQFP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 5.6 Switching Characteristics-- RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 5.7 Switching Characteristics -- XTI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 5.8 Switching Characteristics -- Internal Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5.9 Switching Characteristics -- Serial Control Port - SPI Slave Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 5.10 Switching Characteristics -- Serial Control Port - SPI Master Mode . . . . . . . . . . . . . . . . . . . . . . . . . 15 5.11 Switching Characteristics -- Serial Control Port - I2C Slave Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 5.12 Switching Characteristics -- Serial Control Port - I2C Master Mode . . . . . . . . . . . . . . . . . . . . . . . . . . 17 5.13 Switching Characteristics -- Digital Audio Slave Input Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 5.14 Switching Characteristics -- DSD Slave Input Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 5.15 Switching Characteristics -- Digital Audio Output Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 N 6. Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 7. Environmental, Manufacturing, & Handling Information . . . . . . . . . . . . . . . . . . . . . . . . . . 22 8. Device Pinout Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 O 8.1 CS48DV2B, 48-pin LQFP Pinout Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 8.2 48-pin LQFP Package Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 C 9. Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 DS875F2 Copyright 2009 Cirrus Logic CONFIDENTIAL 3 CS48DV2B Data Sheet 32-bit Audio DSP for Dedicated Dolby Volume and Audistry by Dolby List of Figures List of Tables EN D TI EL A L PH D I RA FT Figure 1. RESET Timing ......................................................................................................................................... 12 Figure 2. XTI Timing ............................................................................................................................................... 12 Figure 3. Serial Control Port - SPI Slave Mode Timing........................................................................................... 14 Figure 4. Serial Control Port - SPI Master Mode Timing......................................................................................... 15 Figure 5. Serial Control Port - I2C Slave Mode Timing ........................................................................................... 16 Figure 6. Serial Control Port - I2C Master Mode Timing ......................................................................................... 17 Figure 7. Digital Audio Input (DAI) Port Timing Diagram ........................................................................................ 18 Figure 8. Direct Stream Digital - Serial Audio Input Timing..................................................................................... 18 Figure 9. Digital Audio Output Port Timing, Master Mode....................................................................................... 20 Figure 10. Digital Audio Output Timing, Slave Mode (Relationship LRCLK to SCLK) ............................................ 20 Figure 11. CS48DV2B 48-Pin LQFP Pinout Diagram ............................................................................................. 23 Figure 12. 48-Pin LQFP Package Drawing ............................................................................................................. 24 C O N FI D Table 1. CS48DV2B DSP Related Documentation................................................................................................5 Table 2. Device and Firmware Selection Guide.....................................................................................................7 Table 3. Ordering Information ..............................................................................................................................21 Table 4. Environmental, Manufacturing, & Handling Information.........................................................................22 4 Copyright 2009 Cirrus Logic CONFIDENTIAL DS875F2 CS48DV2B Data Sheet 32-bit Audio DSP for Dedicated Dolby Volume and Audistry by Dolby 1. Documentation Strategy The CS48DV2B Data Sheet describes CS48DV2B multichannel audio processors. This document should be used in conjunction with the following documents when evaluating or designing a system around the CS48DV2B processors. Table 1. CS48DV2B DSP Related Documentation Document Name Description CS48DV2B Data Sheet This document Includes detailed system design information including Typical Connection Diagrams, Boot-Procedures, Pin Descriptions, etc. EN D TI EL A L PH D I RA FT CS485xx Family Hardware User's Manual AN298 - CS485xx Family Firmware User's Manual DSP Composer User's Manual AN298VPMA,Audistry(R) by Dolby(R)" AN298PPMN, Dolby(R) Volume Firmware User's Manual for the CS48DV2x Family Includes detailed firmware design information including signal processing flow diagrams and control API information Includes detailed configuration and usage information for the GUI development tool. Describes API used to control the Audistry firmware module. Describes API used to control the Dolby Volume firmware module. The scope of the CS48DV2B Data Sheet is primarily the hardware specifications of the CS48DV2B devices. This includes hardware functionality, characteristic data, pinout, and packaging information. The intended audience for the CS48DV2B Data Sheet is the system PCB designer, MCU programmer, and the quality control engineer. 2. Overview FI D The CS48DV2B DSP is designed to provide high-performance post-processing and mixing of digital audio. The dual clock domain provided on the PCM inputs allows for the mixing of audio streams with different sampling frequencies. The low-power standby preserves battery life for applications which are always on, but not necessarily processing audio, such as automotive audio systems. N The CS48DV2B supports dual input clock domains and dual audio processing paths. The CS48DV2B is available in a 48-pin QFP package. Please refer to Table 2 on page 7 for the input, output, firmware features of each device. O 2.1 Licensing C Licenses are required for all of the 3rd party audio processing algorithms listed in Section 3. Please contact your local Cirrus Logic Sales representative for more information. DS875F2 Copyright 2009 Cirrus Logic CONFIDENTIAL 5 CS48DV2B Data Sheet 32-bit Audio DSP for Dedicated Dolby Volume and Audistry by Dolby 3. Code Overlays The suite of software available for the CS48DV2B DSP consists of an operating system (OS) and a library of overlays. The overlays have been divided into three main groups called Matrix-processors, Virtualizer-processors, and Post-processors. All software components are defined below: 1. OS/Kernel - Encompasses all non-audio processing tasks, including loading data from external memory, processing host messages, calling audio-processing subroutines, error concealment, etc. EN D TI EL A L PH D I RA FT 2. Matrix-processor- Any Module that performs a matrix decode on PCM data to produce more output channels than input channels (2On channels). Examples are Dolby(R) Pro Logic(R) IIx and DTS Neo:6TM. Generally speaking, these modules increase the number of valid channels in the audio I/O buffer. 3. Virtualizer-processor - Any module that encodes PCM data into fewer output channels than input channels (nO2 channels) with the effect of providing "phantom" speakers to represent the physical audio channels that were eliminated. Examples are Dolby Headphone(R) and Dolby(R) Virtual Speaker(R). Generally speaking, these modules reduce the number of valid channels in the audio I/O buffer. 4. Post-processors - Any module that processes audio I/O buffer PCM data in-place after the matrix- or virtualizer-processors. Examples are the Dolby Volume and Audistry by Dolby firmware, bass management, audio manager, tone control, EQ, delay, and customer-specific effects The bulk of each overlay is stored in ROM within the CS48DV2B, but a small image is required to configure the overlays and boot the DSP. This small image can either be stored in an external serial FLASH/EEPROM, or downloaded via a host controller through the SPITM/I2C(R) serial port. The overlay structure reduces the time required to reconfigure the DSP when a processing change is requested. Each overlay can be reloaded independently without disturbing the other overlays. For example, when a new matrix-processor is selected, the OS, virtualizer-, and post-processors do not need to be reloaded -- only the new matrix-processor. This fact is also true for the other overlays. C O N FI D Table 2 lists the firmware available based on device selection. Please refer to AN298, CS485xx Firmware User's Manual for the latest listing of application codes and Cirrus FrameworkTM modules available. 6 Copyright 2009 Cirrus Logic CONFIDENTIAL DS875F2 CS48DV2B Data Sheet 32-bit Audio DSP for Dedicated Dolby Volume and Audistry by Dolby Table 2. Device and Firmware Selection Guide Devices Availability CS48DV2B-CQZ In Production Now * Digital TV Portable Audio Docking Station * Portable DVD Players * Multimedia PC Speakers * Soundbars * Automotive Entertainment Systems Specific Features * 2.1 channels of audio input and 2.1 channels of PCM audio output. * 512 FFT Window, 20Bands/Channel * Dolby Volume Native Processing of the following Fs: -- 32 kHz -- 44.1 kHz -- 48 kHz EN D TI EL A L PH D I RA FT CS48DV2B-DQZ Suggested Applications 4. Hardware Functional Description 4.1 DSP Core The CS48DV2B DSPs are single-core DSP with separate X and Y data and P code memory spaces. The DSP core is a high-performance, 32-bit, user-programmable, fixed-point DSP that is capable of performing two multiply-and-accumulate (MAC) operations per clock cycle. The DSP core has eight 72-bit accumulators, four X- and four Y-data registers, and 12 index registers. The DSP core is coupled to a flexible DMA engine. The DMA engine can move data between peripherals such as the serial control port (SCP), digital audio input (DAI) and digital audio output (DAO), or any DSP core memory, all without the intervention of the DSP. The DMA engine off loads data move instructions from the DSP core, leaving more MIPS available for signal processing instructions. D CS48DV2B functionality is controlled by application codes that are stored in on-board ROM or downloaded to the CS48DV2B from a host controller or external serial FLASH/EEPROM. FI Users can develop their applications using DSP Composer to create the processing chain and then compile the image into a series of commands that are sent to the CS48DV2B through the SCP. The processing application can either load modules (matrix-processors, virtualizers, post-processors) from the DSPs on-board ROM, or custom firmware can be downloaded through the SCP. O N The CS48DV2B is suitable for a variety of audio post-processing applications such as automotive head-ends, automotive amplifiers, and boom boxes. 4.1.1 DSP Memory C The DSP core has its own on-chip data and program RAM and ROM and does not require external memory for post-processing applications. The Y-RAM and P-RAM share a single block of memory that can be configured to make Y and P equal in size, or more memory can be allocated for Y-RAM in 2kword blocks. 4.1.2 DMA Controller The powerful 8-channel DMA controller can move data between 8 on-chip resources. Each resource has its own arbiter: X, Y, and P RAMs/ROMs and the peripheral bus. Modulo and linear addressing DS875F2 Copyright 2009 Cirrus Logic CONFIDENTIAL 7 CS48DV2B Data Sheet 32-bit Audio DSP for Dedicated Dolby Volume and Audistry by Dolby modes are supported, with flexible start address and increment controls. The service intervals for each DMA channel, as well as up to 6 interrupt events, are programmable. 4.2 On-chip DSP Peripherals 4.2.1 Digital Audio Input Port (DAI) EN D TI EL A L PH D I RA FT The DAI port supports a wide variety of data input formats at sample rates (Fs) as high as 192 kHz. The port is capable of accepting PCM or DSD formats. Up to 32-bit word lengths are supported. DSD is supported and internally converted to PCM before processing. The DAI also supports a time division multiplexed (TDM) one-line data mode that packs multiple channels of PCM audio input on a single data line. The total number of channels that are possible depends on the ratio of SCLK to LRCLK. The port has two independent slave-only clock domains. Each data input can be independently assigned to a clock domain. The sample rate of the input clock domains can be determined automatically by the DSP, off-loading the task of monitoring the S/PDIF receiver from the host. A time-stamping feature allows the input data to be sample-rate converted via software. 4.2.2 Digital Audio Output Port (DAO) DAO port supports PCM resolutions of up to 32-bits. The port supports sample rates (Fs) as high as 192 kHz. The port can be configured as an independent clock domain mastered by the DSP, or as a clock slave if an external MCLK or SCLK/LRCLK source is available. One of the serial audio pins can be re-configured as a S/PDIF transmitter that drives a bi-phase encoded S/PDIF signal (data with embedded clock on a single line). The DAO also supports a time division multiplexed (TDM) one-line data mode, that packs multiple channels of PCM audio on a single data line. 4.2.3 Serial Control Port (I2C(R) or SPITM) D The on-chip serial control port is capable of operating as master or slave in either SPITM or I2C(R) modes. Master/Slave operation is chosen by mode select pins when the CS48DV2B comes out of Reset. The serial clock pin can support frequencies as high as 25 MHz in SPI mode (SPI clock speed must always be (Fdclk/2)). The CS48DV2B serial control port also includes a pin for flow control of the communications interface (SCP_BSY) and a pin to indicate when the DSP has a message for the host (SCP_IRQ). FI 4.2.4 GPIO N Many of the CS48DV2B peripheral pins are multiplexed with GPIO. Each GPIO can be configured as an output, an input, or an input with interrupt. Each input-pin interrupt can be configured as rising edge, falling edge, active-low, or active-high. O 4.2.5 PLL-based Clock Generator C The low-jitter PLL generates integer or fractional multiples of a reference frequency which are used to clock the DSP core and peripherals. Through a second PLL divider chain, a dependent clock domain can be output on the DAO port for driving audio converters. The CS48DV2B defaults to running from the external reference frequency and is switched to use the PLL output after overlays have been loaded and configured, either through master boot from an external FLASH or through host control. A built-in crystal oscillator circuit with a buffered output is provided. The buffered output frequency ratio is selectable between 1:1 (default) or 2:1. 8 Copyright 2009 Cirrus Logic CONFIDENTIAL DS875F2 CS48DV2B Data Sheet 32-bit Audio DSP for Dedicated Dolby Volume and Audistry by Dolby 4.2.6 Hardware Watchdog Timer The CS48DV2B has an integrated watchdog timer that acts as a "health" monitor for the DSP. The watchdog timer must be reset by the DSP before the counter expires, or the entire chip is reset. This peripheral ensures that the CS48DV2B will reset itself in the event of a temporary system failure. In stand-alone mode (that is, no host MCU), the DSP will reboot from external FLASH. In slave mode (that is, host MCU present) a GPIO will be used to signal the host that the watchdog has expired and the DSP should be rebooted and re-configured. 4.3 DSP I/O Description 4.3.1 Multiplexed Pins EN D TI EL A L PH D I RA FT Many of the CS48DV2B pins are multi-functional. For details on pin functionality please refer to the CS485xx Hardware User's Manual. 4.3.2 Termination Requirements Open-drain pins on the CS48DV2B must be pulled high for proper operation. Please refer to the CS485xx Hardware User's Manual to identify which pins are open-drain and what value of pull-up resistor is required for proper operation. Mode select pins in the CS48DV2B are used to select the boot mode upon the rising edge from reset. A detailed explanation of termination requirements for each communication mode select pin can be found in the CS485xx Hardware User's Manual. 4.3.3 Pads The CS48DV2B I/Os operate from the 3.3 V supply and are 5 V tolerant. 4.4 Application Code Security C O N FI D The external program code may be encrypted by the programmer to protect any intellectual property it may contain. A secret, customer-specific key is used to encrypt the program code that is to be stored external to the device. Please contact your local Cirrus representative for details. DS875F2 Copyright 2009 Cirrus Logic CONFIDENTIAL 9 CS48DV2B Data Sheet 32-bit Audio DSP for Dedicated Dolby Volume and Audistry by Dolby 5. Characteristics and Specifications Note: All data sheet minimum and maximum timing parameters are guaranteed over the rated voltage and temperature. All data sheet typical parameters are measured under the following conditions: T = 25 C, CL = 20 pF, VDD = VDDA = 1.8 V, VDDIO = 3.3 V, GNDD = GNDIO = GNDA = 0 V. 5.1 Absolute Maximum Ratings (GNDD = GNDIO = GNDA = 0 V; all voltages with respect to 0V) Parameter Min Max Unit VDD VDDA VDDIO -0.3 -0.3 -0.3 - 2.0 3.6 3.6 0.3 V V V V Iin - +/-10 mA Core supply PLL supply I/O supply |VDDA - VDDIO| EN D TI EL A L PH D I RA FT DC power supplies: Symbol Input pin current, any pin except supplies Input voltage on PLL_REF_RES Input voltage on I/O pins Storage temperature Vfilt -0.3 3.6 V Vinio -0.3 5.0 V Tstg -65 150 C Caution: Operation at or beyond these limits may result in permanent damage to the device. Normal operation is not guaranteed at these extremes. 5.2 Recommended Operating Conditions (GNDD = GNDIO = GNDA = 0 V; all voltages with respect to 0V) Parameter DC power supplies: Core supply PLL supply I/O supply |VDDA - VDDIO| Ambient operating temperature Symbol Min Typ Max Unit VDD VDDA VDDIO 1.71 3.13 3.13 1.8 3.3 3.3 0 1.89 3.46 3.46 V V V V TA - CS48DV2B-CQZ CS48DV2B-DQZ 0 -40 C +70 +85 D Note: It is recommended that the 3.3 V IO supply come up ahead of or simultaneously with the 1.8 V core supply. FI 5.3 Digital DC Characteristics (Measurements performed under static conditions.) N Parameter High-level input voltage O Low-level input voltage, except XTI Low-level input voltage, XTI Symbol Min Typ Max Unit VIH 2.0 - - V VIL - - 0.8 V VILXTI - - 0.6 V Vhys High-level output voltage (IO = -2mA), except XTI VOH VDDIO * 0.9 Low-level output voltage (IO = 2mA), except XTI VOL Input leakage XTI ILXTI Input leakage current (all digital pins with internal pull-up resistors enabled) ILEAK C Input Hysteresis 10 0.4 Copyright 2009 Cirrus Logic CONFIDENTIAL V - - V - - VDDIO * 0.1 V - - 5 A - - 70 A DS875F2 CS48DV2B Data Sheet 32-bit Audio DSP for Dedicated Dolby Volume and Audistry by Dolby 5.4 Power Supply Characteristics (Measurements performed under operating conditions) Parameter Min Typ Max Unit - 203 8 27 480 - mA mA mA mW - 100 1 50 348 - A A A W Operational Power Supply Current: VDD: Core and I/O operating1 VDDA: PLL operating VDDIO: With most ports operating Total Operational Power Dissipation: EN D TI EL A L PH D I RA FT Standby Power Supply Current: VDD: Core and I/O not clocked VDDA: PLL halted VDDIO: All connected I/O pins 3-stated by other ICs in system Total Standby Power Dissipation: 1. Dependent on application firmware and DSP clock speed. 5.5 Thermal Data (48-Pin LQFP) Parameter Symbol Min Typ Max Unit Tj - - 125 C Thermal Resistance (Junction to Ambient) Two-layer Board1 Four-layer Board2 ja - 63.5 54 - C / Watt Thermal Resistance (Junction to Top of Package) Two-layer Board3 Four-layer Board4 jt - 0.70 0.64 - C / Watt Junction Temperature 1. Two-layer board is specified as a 76 mm X 114 mm, 1.6 mm thick FR-4 material with 1-oz. copper covering 20 % of the top & bottom layers. 2. Four-layer board is specified as a 76 mm X 114 mm, 1.6 mm thick FR-4 material with 1-oz. copper covering 20 % of the top & bottom layers and 0.5-oz. copper covering 90 % of the internal power plane & ground plane layers. 3. To calculate the die temperature for a given power dissipation D Tj = Ambient Temperature + [ (Power Dissipation in Watts) * ja ] FI 4. To calculate the case temperature for a given power dissipation C O N Tc = Tj - [ (Power Dissipation in Watts) * jt ] DS875F2 Copyright 2009 Cirrus Logic CONFIDENTIAL 11 CS48DV2B Data Sheet 32-bit Audio DSP for Dedicated Dolby Volume and Audistry by Dolby 5.6 Switching Characteristics-- RESET Parameter Symbol Min Max Unit Trstl 1 - ms All bidirectional pins high-Z after RESET low Trst2z - 100 ns Configuration pins setup before RESET high Trstsu 50 - ns Configuration pins hold after RESET high Trsthld 20 - ns EN D TI EL A L PH D I RA FT RESET minimum pulse width low RESET HS[3:0] All Bidirectional Pins Trstsu Trsthld Trst2z Trstl Figure 1. RESET Timing 5.7 Switching Characteristics -- XTI Parameter External Crystal operating frequency1 XTI period XTI high time XTI low time D External Crystal Load Capacitance (parallel resonant)2 External Crystal Equivalent Series Resistance Symbol Min Max Unit Fxtal Tclki 11.2896 27 MHz 33.3 100 ns Tclkih 13.3 - ns Tclkil 13.3 - ns CL 10 18 pF 50 ESR FI 1. Part characterized with the following crystal frequency values: 11.2896, 12.288, 18.432, 24.576, & 27 MH.z C O N 2. CL refers to the total load capacitance as specified by the crystal manufacturer. Crystals that require a CL outside this range should be avoided. The crystal oscillator circuit design should follow the crystal manufacturer's recommendation for load capacitor selection. XTI t clkih t clkil Tclki Figure 2. XTI Timing 12 Copyright 2009 Cirrus Logic CONFIDENTIAL DS875F2 CS48DV2B Data Sheet 32-bit Audio DSP for Dedicated Dolby Volume and Audistry by Dolby 5.8 Switching Characteristics -- Internal Clock Parameter Internal DCLK frequency1 Symbol Min Max Fdclk Fxtal Fxtal 150 150 6.7 6.7 1/Fxtal 1/Fxtal CS48DV2B-CQZ CS48DV2B-DQZ Internal DCLK period1 DCLKP CS48DV2B-CQZ CS48DV2B-DQZ Unit MHz ns C O N FI D EN D TI EL A L PH D I RA FT 1. After initial power-on reset, Fdclk = Fxtal. After initial kickstart commands, the PLL is locked to max Fdclk and remains locked until the next power-on reset. DS875F2 Copyright 2009 Cirrus Logic CONFIDENTIAL 13 CS48DV2B Data Sheet 32-bit Audio DSP for Dedicated Dolby Volume and Audistry by Dolby 5.9 Switching Characteristics -- Serial Control Port - SPI Slave Mode. Parameter Symbol Min Max Units SCP_CLK frequency fspisck - 25 MHz SCP_CS falling to SCP_CLK rising tspicss 24 - ns SCP_CLK low time tspickl 20 - ns SCP_CLK high time tspickh 20 - ns Setup time SCP_MOSI input tspidsu 5 - ns Hold time SCP_MOSI input tspidh 5 - ns SCP_CLK low to SCP_MISO output valid tspidov - 11 ns SCP_CLK falling to SCP_IRQ rising tspiirqh - 20 ns SCP_CS rising to SCP_IRQ falling tspiirql 0 tspicsh 24 SCP_CS rising to SCP_MISO output high-Z tspicsdz - 20 ns SCP_CLK rising to SCP_BSY falling tspicbsyl - 3*DCLKP+20 ns SCP_CLK low to SCP_CS rising Typical EN D TI EL A L PH D I RA FT 1 - ns ns 1. The specification fspisck indicates the maximum speed of the hardware. The system designer should be aware that the actual maximum speed of the communication port may be limited by the firmware application. Flow control using the SCP_BSY pin should be implemented to prevent overflow of the input data buffer. At boot the maximum speed is Fxtal/3. tspicss SCP_CS tspickl 0 SCP_CLK fspisck A5 D tspidsu 6 7 0 A0 R/W MSB 5 6 7 tspicsh LSB tspidov tspicsdz MSB N FI tspidh SCP_MISO 2 tspickh A6 SCP_MOSI 1 LSB O tspiirqh tspiirql SCP_IRQ C tspibsyl SCP_BSY Figure 3. Serial Control Port - SPI Slave Mode Timing 14 Copyright 2009 Cirrus Logic CONFIDENTIAL DS875F2 CS48DV2B Data Sheet 32-bit Audio DSP for Dedicated Dolby Volume and Audistry by Dolby 5.10 Switching Characteristics -- Serial Control Port - SPI Master Mode Parameter Symbol 1 Min fspisck - tspicss - SCP_CLK low time tspickl SCP_CLK high time Typical Max Units 2 Fxtal/2 MHz - ns 20 - ns tspickh 20 - ns Setup time SCP_MISO input tspidsu 9 - ns Hold time SCP_MISO input tspidh 5 - ns SCP_CLK frequency 11*DCLKP + (SCP_CLK PERIOD)/2 EN D TI EL A L PH D I RA FT SCP_CS falling to SCP_CLK rising 3 SCP_CLK low to SCP_MOSI output valid tspidov - 8 ns SCP_CLK low to SCP_CS falling tspicsl 7 - ns tspicsh - 11*DCLKP + (SCP_CLK PERIOD)/2 - ns 3*DCLKP - ns 20 ns SCP_CLK low to SCP_CS rising Bus free time between active SCP_CS tspicsx SCP_CLK falling to SCP_MOSI output high-Z tspidz - 1. The specification fspisck indicates the maximum speed of the hardware. The system designer should be aware that the actual maximum speed of the communication port may be limited by the firmware application. 2. See Section 5.7. 3. SCP_CLK PERIOD refers to the period of SCP_CLK as being used in a given application. It does not refer to a tested parameter tspicsx tspicss EE_CS# tspickl tspicsl 0 SCP_MISO FI fspisck D SCP_CLK 1 A6 A5 2 6 7 0 A0 R/W MSB 5 7 6 tspicsh tspickh LSB N tspidsu tspidov tspidz MSB LSB C O SCP_MOSI tspidh DS875F2 Figure 4. Serial Control Port - SPI Master Mode Timing Copyright 2009 Cirrus Logic CONFIDENTIAL 15 CS48DV2B Data Sheet 32-bit Audio DSP for Dedicated Dolby Volume and Audistry by Dolby 5.11 Switching Characteristics -- Serial Control Port - I2C Slave Mode Parameter Symbol Min Max Units SCP_CLK frequency fiicck - 400 kHz SCP_CLK low time tiicckl 1.25 - s SCP_CLK high time tiicckh 1.25 - s tiicckcmd 1.25 START condition to SCP_CLK falling tiicstscl 1.25 - s SCP_CLK falling to STOP condition tiicstp 2.5 - s Bus free time between STOP and START conditions tiicbft 3 - s Setup time SCP_SDA input valid to SCP_CLK rising tiicsu 100 Hold time SCP_SDA input after SCP_CLK falling tiich 20 - ns SCP_CLK low to SCP_SDA out valid tiicdov - 18 ns SCP_CLK falling to SCP_IRQ rising tiicirqh - 3*DCLKP + 40 ns NAK condition to SCP_IRQ low tiicirql 1 SCP_CLK rising to SCB_BSY low s EN D TI EL A L PH D I RA FT SCP_CLK rising to SCP_SDA rising or falling for START or STOP condition Typical tiicbsyl - ns 3*DCLKP + 20 ns 3*DCLKP + 20 ns 1. The specification fiicck indicates the maximum speed of the hardware. The system designer should be aware that the actual maximum speed of the communication port may be limited by the firmware application. Flow control using the SCP_BSY pin should be implemented to prevent overflow of the input data buffer. tiicckcmd tiicckl 0 1 SCP_CLK tiicckh A6 FI SCP_SDA tiicf 7 8 tiicckcmd 0 tiicdov A0 R/W 1 6 7 8 tiicstp fiicck ACK MSB LSB tiicbft ACK tiicirqh tiicirql tiich O N tiicsu SCP_IRQ 6 D tiicstscl tiicr tiiccbsyl C SCP_BSY Figure 5. Serial Control Port - I2C Slave Mode Timing 16 Copyright 2009 Cirrus Logic CONFIDENTIAL DS875F2 CS48DV2B Data Sheet 32-bit Audio DSP for Dedicated Dolby Volume and Audistry by Dolby 5.12 Switching Characteristics -- Serial Control Port - I2C Master Mode Parameter Symbol Min Max Units fiicck - 400 kHz SCP_CLK low time tiicckl 1.25 - s SCP_CLK high time tiicckh 1.25 - s tiicckcmd 1.25 START condition to SCP_CLK falling tiicstscl 1.25 - s SCP_CLK falling to STOP condition SCP_CLK frequency1 SCP_SCK rising to SCP_SDA rising or falling for START or STOP condition s 2.5 - s tiicbft 3 - s Setup time SCP_SDA input valid to SCP_CLK rising tiicsu 100 Hold time SCP_SDA input after SCP_CLK falling tiich 20 - ns tiicdov - 18 ns EN D TI EL A L PH D I RA FT tiicstp Bus free time between STOP and START conditions SCP_CLK low to SCP_SDA out valid ns 1. The specification fiicck indicates the maximum speed of the hardware. The system designer should be aware that the actual maximum speed of the communication port may be limited by the firmware application. tiicckcmd tiicckl 0 1 SCP_CLK tiicstscl 6 tiicckh A6 SCP_SDA tiicr 8 0 tiicdov A0 tiich 7 tiicckcmd R/W 1 6 7 8 tiicstp fiicck ACK MSB LSB tiicbf ACK D tiicsu tiicf C O N FI Figure 6. Serial Control Port - I2C Master Mode Timing DS875F2 Copyright 2009 Cirrus Logic CONFIDENTIAL 17 CS48DV2B Data Sheet 32-bit Audio DSP for Dedicated Dolby Volume and Audistry by Dolby 5.13 Switching Characteristics -- Digital Audio Slave Input Port Parameter Symbol Min Max Unit Tdaiclkp 40 - ns - 45 55 % Setup time DAI_DATAn tdaidsu 10 - ns Hold time DAI_DATAn tdaidh 5 - ns DAI_SCLK period DAI_SCLK duty cycle EN D TI EL A L PH D I RA FT DAI_SCLK tdaidsu tdaidh DAI_DATAn Figure 7. Digital Audio Input (DAI) Port Timing Diagram 5.14 Switching Characteristics -- DSD Slave Input Port Min 78 78 1.024 20 20 Typ - Max 3.2 - Unit ns ns MHz ns ns C O N FI D Parameter Symbol DSD_SCLK Pulse Width Low tsclkl DSD_SCLK Pulse Width High tsclkh DSD_SCLK Frequency (64x Oversampled) DSD_A / _B valid to DSD_SCLK rising setup time tsdlrs DSD_SCLK rising to DSD_A or DSD_B hold time tsdh Figure 8. Direct Stream Digital - Serial Audio Input Timing 18 Copyright 2009 Cirrus Logic CONFIDENTIAL DS875F2 CS48DV2B Data Sheet 32-bit Audio DSP for Dedicated Dolby Volume and Audistry by Dolby 5.15 Switching Characteristics -- Digital Audio Output Port Parameter DAO_MCLK period Symbol Min Max Unit Tdaomclk 40 - ns - 45 55 % DAO_MCLK duty cycle 1 DAO_SCLK period for Master or Slave mode Tdaosclk 40 - ns - 40 60 % DAO_SCLK delay from DAO_MCLK rising edge, DAO_MCLK as an input tdaomsck - 19 ns DAO_LRCLK delay from DAO_SCLK transition, respectively3 tdaomstlr - respectively3 tdaomlrts - 8 ns tdaomdv - 10 ns tdaosdv - 15 ns DAO_LRCLK delay from DAO_SCLK transition, respectively3 tdaosstlr - 30 ns 3 tdaoslrts - 15 ns DAO_SCLK duty cycle for Master or Slave mode1 EN D TI EL A L PH D I RA FT Master Mode (Output A1 Mode)1,2 DAO_SCLK delay from DAO_LRCLK transition, DAO1_DATA[3..0], DAO2_DATA[1..0] delay from DAO_SCLK transition3 8 ns Slave Mode (Output A0 Mode)4 DAO1_DATA[3..0], DAO2_DATA[1..0] delay from DAO_SCLK transition3 DAO_SCLK delay from DAO_LRCLK transition, respectively 1. Master mode timing specifications are characterized, not production tested. 2. Master mode is defined as the CS48DVxx driving both DAO_SCLK, DAO_LRCLK. When MCLK is an input, it is divided to produce DAO_SCLK, DAO_LRCLK. 3. This timing parameter is defined from the non-active edge of DAO_SCLK. The active edge of DAO_SCLK is the point at which the data is valid. 4. Slave mode is defined as DAO_SCLK, DAO_LRCLK driven by an external source. tdaomlclk DAO_MCLK tdaomclk DAO_MCLK N tdaomdv tdaomsck DAO_SCLK FI DAO_SCLK D tdaomsck O DAOn_DATAn tdaomlrts tdaomstlr DAO_LRCLK C DAO_LRCLK DAOn_DATAn Note: In these diagrams, Falling edge is the inactive edge of DAO_SCLK DS875F2 Copyright 2009 Cirrus Logic CONFIDENTIAL 19 CS48DV2B Data Sheet 32-bit Audio DSP for Dedicated Dolby Volume and Audistry by Dolby Figure 9. Digital Audio Output Port Timing, Master Mode tdaosstlr tdaosclk DAO_LRCLK DAO_LRCLK DAO_SCLK tdaosclk tdaoslrts EN D TI EL A L PH D I RA FT DAOn_DATAn DAO_SCLK tdaosdv Note: In these diagrams, Falling edge is the inactive edge of DAO_SCLK C O N FI D Figure 10. Digital Audio Output Timing, Slave Mode (Relationship LRCLK to SCLK) 20 Copyright 2009 Cirrus Logic CONFIDENTIAL DS875F2 CS48DV2B Data Sheet 32-bit Audio DSP for Dedicated Dolby Volume and Audistry by Dolby 6. Ordering Information The CS48DV2B part number is described as follows: CS48DVNI-XYZR where N - Product Number Variant I - ROM ID Number X - Product Grade Z - Lead (Pb) Free EN D TI EL A L PH D I RA FT Y - Package Type R - Tape and Reel Packaging Table 3. Ordering Information Part No. CS48DV2B-CQZ CS48DV2B-DQZ Grade Temp. Range Package Commercial 0 to +70 C 48-pin LQFP Automotive -40 to +85 C 48-pin LQFP C O N FI D NOTE: Please contact the factory for availability of the -D (automotive grade) package. DS875F2 Copyright 2009 Cirrus Logic CONFIDENTIAL 21 CS48DV2B Data Sheet 32-bit Audio DSP for Dedicated Dolby Volume and Audistry by Dolby 7. Environmental, Manufacturing, & Handling Information Table 4. Environmental, Manufacturing, & Handling Information Model Number Peak Reflow Temp MSL Rating* Max Floor Life 260 C 3 7 Days CS48DV2B-CQZ CS48DV2B-CQZR CS48DV2B-DQZ CS48DV2B-DQZR C O N FI D EN D TI EL A L PH D I RA FT * MSL (Moisture Sensitivity Level) as specified by IPC/JEDEC J-STD-020. 22 Copyright 2009 Cirrus Logic CONFIDENTIAL DS875F2 CS48DV2B Data Sheet 32-bit Audio DSP for Dedicated Dolby Volume and Audistry by Dolby 8. Device Pinout Diagrams GPIO4, DAO1_ DATA2, HS2 GPIO18, DAO_MCLK 26 25 GNDIO3 30 GPIO3, DAO1_ DATA1, HS1 GPIO6, DAO2 _DATA0, HS3 31 27 GPIO7, DAO2_D ATA1, HS4 32 VDD2 GND4 33 28 GPIO9, SCP_MOSI 34 CS48DV2B 42 10 11 12 GPIO16, DAI1_DATA0, TM0, DSD0 GPIO0, DAI1_DATA1, TM1, DSD1 VDDIO1 DBDA RESET# FI TEST N GND3 DAO_LRCLK 20 DAO1_DATA0, HS0 GNDIO2 18 GPIO15, DAI2_SCLK 17 GPIO14, DAI2_LRCLK 16 VDD1 15 GPIO17, DAI2_DATA0, DSD4 14 GPIO2, DAI1_DATA3, TM3, DSD3 13 GPIO1, DAI1_DATA2, TM2, DSD2 C O 9 48 GND2 VDDA (3.3V) 8 47 DAI1_SCLK, DSD-CLK PLL_REF_RES 7 46 GNDIO1 GNDA 6 45 DAI1_LRCLK, DAI1_DATA4, DSD5 XTO 5 44 1 XTI DAO_SCLK 21 19 48-Pin LQFP 43 VDDIO2 EN D TI EL A L PH D I RA FT 41 D XTAL_OUT 40 3 VDD3 22 2 GPIO13, SCP_BSY , EE_CS GPIO5, DAO1_DATA3, X MTA GPIO10, SCP__MISO / SDA 35 23 39 GNDIO4 29 GPIO11, SCP_CLK 38 DBCK GPOI12, SCP_IRQ 24 4 GPIO8, SCP_CS 37 GND1 VDDIO3 36 8.1 CS48DV2B, 48-pin LQFP Pinout Diagram Figure 11. CS48DV2B 48-Pin LQFP Pinout Diagram DS875F2 Copyright 2009 Cirrus Logic CONFIDENTIAL 23 CS48DV2B Data Sheet 32-bit Audio DSP for Dedicated Dolby Volume and Audistry by Dolby 8.2 48-pin LQFP Package Drawing D Number of Leads 48 MIN NOM MAX 1.60 0.05 0.15 1.35 1.40 1.45 0.17 0.22 0.27 9.00 BSC 7.00 BSC 0.50 BSC 9.00 BSC 7.00 BSC 0 7 0.45 0.60 0.75 1.00 REF C O N FI A A1 A2 b D D1 e E E1 theta L L1 EN D TI EL A L PH D I RA FT 48 LD LQFP (7 x 7 x 1.4 mm body) NOTES: 1) Reference document: JEDEC MS-026 2) All dimensions are in millimeters and controlling dimension is in millimeters. 3) D1 and E1 do not include mold flash which is 0.25 mm max. per side.A1 4) Dimension b does not include a total allowable dambar protrusion of 0.08 mm max. Figure 12. 48-Pin LQFP Package Drawing 24 Copyright 2009 Cirrus Logic CONFIDENTIAL DS875F2 CS48DV2B Data Sheet 32-bit Audio DSP for Dedicated Dolby Volume and Audistry by Dolby 9. Revision History Date Changes F1 December 3, 2008 Initial Release of CS48DV2B Data Sheet F2 February 16, 2009 Updated Section 5.5, adding Junction Temperature specification. C O N FI D EN D TI EL A L PH D I RA FT Revision DS875F2 Copyright 2009 Cirrus Logic CONFIDENTIAL 25 C O N FI D EN D TI EL A L PH D I RA FT CS48DV2B Data Sheet 32-bit Audio DSP for Dedicated Dolby Volume and Audistry by Dolby 26 Copyright 2009 Cirrus Logic CONFIDENTIAL DS875F2 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Cirrus Logic: CS48DV2A-DQZ CS48DV2A-DQZR