70
75
80
85
90
95
100
0 0.5 1 1.5 2 2.5
Output Current (A)
Efficiency (%)
VIN = 24 V, VOUT = 15 V, fSW = 1 MHz
VIN = 24 V, VOUT = 12 V, fSW = 800 kHz
G000
VOUTVIN
LMZ35003
VADJ
AGND PGND
V
OUT
V
IN
PWRGD
RT/CLK
INH/UVLO
SS/TR
STSEL
C
IN
R
SET
C
OUT
Product
Folder
Order
Now
Technical
Documents
Tools &
Software
Support &
Community
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LMZ35003
SNVS988B –JULY 2013–REVISED APRIL 2018
LMZ35003 2.5-A Power Module With 7V-50V Input in QFN Package
1
1 Features
1• Complete Integrated Power Solution Allows
Small Footprint, Low-Profile Design
• Wide Input Voltage Range from 7 V to 50 V
• Output Adjustable from 2.5 V to 15 V
• 65-V Surge Capability
• Efficiencies Up To 96%
• Adjustable Switching Frequency
(300 kHz to 1 MHz)
• Synchronizes to an External Clock
• Adjustable Slow-Start
• Output Voltage Sequencing and Tracking
• Power Good Output
• Programmable Undervoltage Lockout (UVLO)
• Output Overcurrent Protection
• Over Temperature Protection
• Pre-bias Output Start-up
• Operating Temperature Range: –40°C to 85°C
• Enhanced Thermal Performance: 14°C/W
• Meets EN55022 Class B Emissions
- Integrated Shielded Inductor
• For Design Help visit http://www.ti.com/LMZ35003
• Create a Custom Design Using the LMZ35003
With the WEBENCH®Power Designer
2 Applications
• Industrial and Motor Controls
• Automated Test Equipment
• Medical and Imaging Equipment
• High Density Power Systems
3 Description
The LMZ35003 power module is an easy-to-use
integrated power solution that combines a 2.5-A
DC/DC converter with a shielded inductor and
passives into a low profile, QFN package. This total
power solution allows as few as five external
components and eliminates the loop compensation
and magnetics part selection process.
The small 9 mm × 11 mm × 2.8 mm, QFN package is
easy to solder onto a printed circuit board and allows
a compact point-of-load design with greater than 90%
efficiency and excellent power dissipation capability.
The LMZ35003 offers the flexibility and the feature-
set of a discrete point-of-load design and is ideal for
powering a wide range of ICs and systems.
Advanced packaging technology affords a robust and
reliable power solution compatible with standard QFN
mounting and testing techniques.
Simplified Application
2
LMZ35003
SNVS988B –JULY 2013–REVISED APRIL 2018
www.ti.com
Product Folder Links: LMZ35003
Submit Documentation Feedback Copyright © 2013–2018, Texas Instruments Incorporated
Table 1. Ordering Information
For the most current package and ordering information, see the Package Option Addendum at the end of this datasheet, or see
the TI website at www.ti.com.
(1) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) See the temperature derating curves in the Typical Characteristics section for thermal information.
(3) For soldering specifications, refer to the Soldering Requirements for BQFN Packages application note.
(4) Devices with a date code prior to week 14 2018 (1814) have a peak reflow case temperature of 240°C with a maximum of one reflow.
4 Specifications
4.1 Absolute Maximum Ratings(1)
over operating temperature range (unless otherwise noted) MIN MAX UNIT
Input Voltage
VIN –0.3 65 V
INH/UVLO –0.3 5 V
VADJ –0.3 3 V
PWRGD –0.3 6 V
SS/TR –0.3 3 V
STSEL –0.3 3 V
RT/CLK –0.3 3.6 V
Output Voltage PH –0.6 65 V
PH 10ns Transient –2 65 V
VOUT –0.6 VIN V
VDIFF (GND to exposed thermal
pad) ±200 mV
Source Current RT/CLK 100 µA
INH/UVLO 100 µA
Sink Current SS/TRK 200 µA
PWRGD 10 mA
Operating Junction Temperature –40 105(2) °C
Storage Temperature –65 150 °C
Peak Reflow Case Temperature(3) 250(4) °C
Maximum Number of Reflows Allowed(3) 3(4)
Mechanical Shock Mil-STD-883D, Method 2002.3, 1 msec, 1/2 sine, mounted 1500 G
Mechanical Vibration Mil-STD-883D, Method 2007.2, 20-2000Hz 20
4.2 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted) MIN MAX UNIT
VIN Input Voltage 7 50 V
VOUT Output Voltage 2.5 15 V
fSW Switching Frequency 400 1000 kHz
TAOperating Ambient Temperature -40 85 °C
3
LMZ35003
www.ti.com
SNVS988B –JULY 2013–REVISED APRIL 2018
Product Folder Links: LMZ35003
Submit Documentation FeedbackCopyright © 2013–2018, Texas Instruments Incorporated
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics (SPRA953)
application report.
(2) The junction-to-ambient thermal resistance, θJA, applies to devices soldered directly to a 100 mm x 100 mm double-sided, 4-layer PCB
with 1 oz. copper and natural convection cooling. Additional airflow reduces θJA.
(3) The junction-to-top characterization parameter, ψJT, estimates the junction temperature, TJ, of a device in a real system, using a
procedure described in JESD51-2A (sections 6 and 7). TJ=ψJT * Pdis + TT; where Pdis is the power dissipated in the device and TTis
the temperature of the top of the device.
(4) The junction-to-board characterization parameter, ψJB, estimates the junction temperature, TJ, of a device in a real system, using a
procedure described in JESD51-2A (sections 6 and 7). TJ=ψJB * Pdis + TB; where Pdis is the power dissipated in the device and TBis
the temperature of the board 1mm from the device.
4.3 Thermal Information
THERMAL METRIC(1) LMZ35003
UNITRKG
41 PINS
θJA Junction-to-ambient thermal resistance(2) 14 °C/WψJT Junction-to-top characterization parameter(3) 3.3
ψJB Junction-to-board characterization parameter(4) 6.8
4.4 Package Specifications LMZ35003 UNIT
Weight 0.9 grams
Flammability Meets UL 94 V-O
MTBF Calculated reliability Per Bellcore TR-332, 50% stress, TA= 40°C, ground benign 31.7 MHrs
(1) For output voltages ≤12 V, the minimum input voltage is 7 V or (VOUT+ 3 V), whichever is greater. For output voltages > 12 V, the
minimum input voltage is (1.33 x VOUT). See Figure 27 for more details.
(2) The maximum input voltage is 50 V or (15 x VOUT), whichever is less.
(3) Output voltages < 3.3 V are subject to reduced VIN(max) specifications and higher ripple magnitudes.
(4) The stated limit of the set-point voltage tolerance includes the tolerance of both the internal voltage reference and the internal
adjustment resistor. The overall output voltage tolerance is affected by the tolerance of the external RSET resistor.
(5) Value when no voltage divider is present at the INH/UVLO pin.
4.5 Electrical Characteristics
-40°C ≤TA≤+85°C, VIN = 24 V, VOUT = 5.0 V, IOUT = 2.5 A, RT= Open
CIN = 2 x 2.2 µF ceramic, COUT = 2 x 47 µF ceramic (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
IOUT Output current Over input voltage and output voltage range 0 2.5 A
VIN Input voltage range Over output current range 7.0(1) 50(2) V
UVLO VIN Undervoltage lockout No hysteresis, Rising and Falling 2.5 V
VOUT(adj) Output voltage adjust range Over output current range 2.5(3) 15 V
VOUT
Set-point voltage tolerance TA= 25°C; IOUT = 100 mA ±2.0% (4)
Temperature variation -40°C ≤TA≤+85°C ±0.5% ±1.0%
Line regulation Over input voltage range ±0.1%
Load regulation Over output current range ±0.4%
Total output voltage variation Includes set-point, line, load, and temperature variation ±3.0% (4)
ηEfficiency
VIN = 24 V
IOUT = 1.5 A
VOUT = 12 V, fSW = 800 kHz 93 %
VOUT = 5.0 V, fSW = 500 kHz 84 %
VOUT = 3.3 V, fSW = 400 kHz 79 %
VIN = 48 V
IOUT = 1.5 A VOUT = 12 V, fSW = 800 kHz 87 %
VOUT = 5.0 V, fSW = 500 kHz 79 %
VOUT = 3.3 V, fSW = 400 kHz 74 %
Output voltage ripple 20 MHz bandwith, 0.25 A ≤IOUT ≤2.5 A, VOUT ≥3.3V 1% (3) VOUT
ILIM Current limit threshold 5.1 A
Transient response 1.0 A/µs load step from 50 to 100%
IOUT(max)
Recovery time 400 µs
VOUT
over/undershoot 90 mV
VINH Inhibit threshold voltage No hysteresis 1.15 1.25 1.36 (5) V
4
LMZ35003
SNVS988B –JULY 2013–REVISED APRIL 2018
www.ti.com
Product Folder Links: LMZ35003
Submit Documentation Feedback Copyright © 2013–2018, Texas Instruments Incorporated
Electrical Characteristics (continued)
-40°C ≤TA≤+85°C, VIN = 24 V, VOUT = 5.0 V, IOUT = 2.5 A, RT= Open
CIN = 2 x 2.2 µF ceramic, COUT = 2 x 47 µF ceramic (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
(6) A minimum of 4.4µF of ceramic external capacitance is required across the input (VIN and PGND connected) for proper operation.
Locate the capacitor close to the device. See Table 3 for more details.
(7) The required capacitance must include at least 2 x 47µF ceramic capacitors (or 4 x 22µF). Locate the capacitance close to the device.
Adding additional capacitance close to the load improves the response of the regulator to load transients. See Table 3 for more details.
IINH INH Input current VINH < 1.15 V -0.9 μA
VINH > 1.36 V -3.8 μA
II(stby) Input standby current INH pin to AGND 1.3 4 µA
Power Good PWRGD Thresholds
VOUT rising Good 94%
Fault 109%
VOUT falling Fault 91%
Good 106%
PWRGD Low Voltage I(PWRGD) = 3.5 mA 0.2 V
fSW Switching frequency RT/CLK pin OPEN 300 400 500 kHz
fCLK Synchronization frequency
CLK Control
300 1000 kHz
VCLK-H CLK High-Level Threshold 1.9 2.2 V
VCLK-L CLK Low-Level Threshold 0.5 0.7 V
DCLK CLK Duty cycle 25% 50% 75%
Thermal Shutdown Thermal shutdown 180 °C
Thermal shutdown hysteresis 15 °C
CIN External input capacitance Ceramic 4.4 (6) 10 µF
Non-ceramic 22
COUT External output capacitance 100 (7) 430 µF
PWRGD
VIN
PGND
PH
VOUT
RT/CLK
VADJ
STSEL
SS/TR
LMZ35003
PWRGD
Logic
+
+
VREF Comp
Power
Stage
and
Control
Logic
Thermal Shutdown
Shutdown
Logic
OCP VIN
UVLO
OSC w/PLL
AGND
INH/UVLO
5
LMZ35003
www.ti.com
SNVS988B –JULY 2013–REVISED APRIL 2018
Product Folder Links: LMZ35003
Submit Documentation FeedbackCopyright © 2013–2018, Texas Instruments Incorporated
5 Device Information
FUNCTIONAL BLOCK DIAGRAM
6
LMZ35003
SNVS988B –JULY 2013–REVISED APRIL 2018
www.ti.com
Product Folder Links: LMZ35003
Submit Documentation Feedback Copyright © 2013–2018, Texas Instruments Incorporated
Table 2. PIN DESCRIPTIONS
TERMINAL DESCRIPTION
NAME NO.
AGND
1
These pins are connected to the internal analog ground (AGND) of the device. This node should be treated
as the zero volt ground reference for the analog control circuitry. Pad 37 should be connected to PCB
ground planes using multiple vias for good thermal performance. Not all pins are connected together
internally. All pins must be connected together externally with a copper plane or pour directly under the
module. Connect AGND to PGND at a single point (GND_PT; pins 8 & 9). See Layout Recommendations.
4
5
30
32
33
34
37
DNC 2Do Not Connect. Do not connect these pins to AGND, to another DNC pin, or to any other voltage. These
pins are connected to internal circuitry. Each pin must be soldered to an isolated pad.
3
25
PH
6
Phase switch node. Do not place any external component on these pins or tie them to a pin of another
function.
7
21
22
23
24
38
41
GND_PT 8Ground Point. Connect AGND to PGND at these pins as shown in the Layout Considerations. These pins
are not connected to internal circuitry, and are not connected to one other.
9
VOUT
10
Output voltage. These pins are connected to the internal output inductor. Connect these pins to the output
load and connect external bypass capacitors between these pins and PGND. Connect a resistor from these
pins to VADJ to set the output voltage.
11
12
13
14
15
39
PGND
16
This is the return current path for the power stage of the device. Connect these pins to the load and to the
bypass capacitors associated with VIN and VOUT. Pad 40 should be connected to PCB ground planes using
multiple vias for good thermal performance.
17
18
19
20
40
VIN 26 Input voltage. This pin supplies all power to the converter. Connect this pin to the input supply and connect
bypass capacitors between this pin and PGND.
INH/UVLO 27 Inhibit and UVLO adjust pin. Use an open drain or open collector logic device to ground this pin to control
the INH function. A resistor divider between this pin, AGND, and VIN sets the UVLO voltage.
SS/TR 28 Slow-start and tracking pin. Connecting an external capacitor to this pin adjusts the output voltage rise time.
A voltage applied to this pin allows for tracking and sequencing control.
STSEL 29 Slow-start or track feature select. Connect this pin to AGND to enable the internal SS capacitor. Leave this
pin open to enable the TR feature.
RT/CLK 31 This pin is connected to an internal frequency setting resistor which sets the default switching frequency. An
external resistor can be connected from this pin to AGND to increase the frequency. This pin can also be
used to synchronize to an external clock.
PWRGD 35 Power Good flag pin. This open drain output asserts low if the output voltage is more than approximately
±6% out of regulation. A pull-up resistor is required.
VADJ 36 Connecting a resistor between this pin and VOUT sets the output voltage.
1
2
3
4
5
6
7
8
9
10
11 12 13 14 15 16 17 18 19
20
21
22
23
24
25
26
27
28
2930313233343536
37
38
39
40
41
STSEL
SS/TR
INH/UVLO
VIN
DNC
PH
PH
PH
PH
PGND
PGND
VADJ
PWRGD
AGND
AGND
AGND
RT/CLK
AGND
AGND
DNC
DNC
AGND
AGND
PH
PH
GND_PT
GND_PT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
PGND
PGND
PGND
PH
PH
AGND
VOUT
PGND
7
LMZ35003
www.ti.com
SNVS988B –JULY 2013–REVISED APRIL 2018
Product Folder Links: LMZ35003
Submit Documentation FeedbackCopyright © 2013–2018, Texas Instruments Incorporated
RKG PACKAGE
(TOP VIEW)
0
0.5
1
1.5
2
2.5
0 0.5 1 1.5 2 2.5
Output Current (A)
Power Dissipation (W)
VOUT = 5.0 V, fSW = 500 kHz
VOUT = 3.3 V, fSW = 400 kHz
VOUT = 2.5 V, fSW = 400 kHz
G000
20
30
40
50
60
70
80
90
0 0.5 1 1.5 2 2.5
Output Current (A)
Ambient Temperature (°C)
Natural ConvectionAll Output Voltages
G000
50
55
60
65
70
75
80
85
90
95
100
0 0.5 1 1.5 2 2.5
Output Current (A)
Efficiency (%)
VOUT = 5.0 V, fSW = 500 kHz
VOUT = 3.3 V, fSW = 400 kHz
VOUT = 2.5 V, fSW = 400 kHz
G000
0
10
20
30
40
0 0.5 1 1.5 2 2.5
Output Current (A)
Output Voltage Ripple (mV)
VOUT = 5.0 V, fSW = 500 kHz
VOUT = 3.3 V, fSW = 400 kHz
VOUT = 2.5 V, fSW = 400 kHz
G000
8
LMZ35003
SNVS988B –JULY 2013–REVISED APRIL 2018
www.ti.com
Product Folder Links: LMZ35003
Submit Documentation Feedback Copyright © 2013–2018, Texas Instruments Incorporated
6 Typical Characteristics (VIN = 12 V)
The electrical characteristic data has been developed from actual products tested at 25°C. This data is considered typical for
the converter. Applies to Figure 1,Figure 2, and Figure 3. The temperature derating curves represent the conditions at which
internal components are at or below the manufacturer's maximum operating temperatures. Derating limits apply to devices
soldered directly to a 100 mm × 100 mm double-sided PCB with 1 oz. copper. Applies to Figure 4.
Figure 1. Efficiency vs. Output Current Figure 2. Voltage Ripple vs. Output Current
Figure 3. Power Dissipation vs. Output Current Figure 4. Safe Operating Area
Figure 5. VOUT= 5 V, IOUT= 2 A, COUT1= 44 µF ceramic, COUT2=
56 µF electrolytic, fSW= 500 kHz Figure 6. VOUT= 3.3 V, IOUT= 2 A, COUT1= 44 µF ceramic,
COUT2= 56 µF electrolytic, fSW= 400 kHz
0
0.5
1
1.5
2
2.5
3
0 0.5 1 1.5 2 2.5
Output Current (A)
Power Dissipation (W)
VOUT = 15 V, fSW = 1 MHz
VOUT = 12 V, fSW = 800 kHz
VOUT = 5.0 V, fSW = 500 kHz
VOUT = 3.3 V, fSW = 400 kHz
VOUT = 2.5 V, fSW = 400 kHz
G000
20
30
40
50
60
70
80
90
0 0.5 1 1.5 2 2.5
Output Current (A)
Ambient Temperature (°C)
Natural ConvectionAll Output Voltages
G000
50
55
60
65
70
75
80
85
90
95
100
0 0.5 1 1.5 2 2.5
Output Current (A)
Efficiency (%)
VOUT = 15 V, fSW = 1 MHz
VOUT = 12 V, fSW = 800 kHz
VOUT = 5.0 V, fSW = 500 kHz
VOUT = 3.3 V, fSW = 400 kHz
VOUT = 2.5 V, fSW = 400 kHz
G000
0
10
20
30
40
50
60
0 0.5 1 1.5 2 2.5
Output Current (A)
Output Voltage Ripple (mV)
VOUT = 15 V, fSW = 1 MHz
VOUT = 12 V, fSW = 800 kHz
VOUT = 5.0 V, fSW = 500 kHz
VOUT = 3.3 V, fSW = 400 kHz
VOUT = 2.5 V, fSW = 400 kHz
G000
9
LMZ35003
www.ti.com
SNVS988B –JULY 2013–REVISED APRIL 2018
Product Folder Links: LMZ35003
Submit Documentation FeedbackCopyright © 2013–2018, Texas Instruments Incorporated
7 Typical Characteristics (VIN = 24 V)
The electrical characteristic data has been developed from actual products tested at 25°C. This data is considered typical for
the converter. Applies to Figure 7,Figure 8, and Figure 9. At light load the output voltage ripple may increase due to pulse
skipping. See Light-Load Behavior for more information. Applies to Figure 8. The temperature derating curves represent the
conditions at which internal components are at or below the manufacturer's maximum operating temperatures. Derating limits
apply to devices soldered directly to a 100 mm × 100 mm double-sided PCB with 1 oz. copper. Applies to Figure 10.
Figure 7. Efficiency vs. Output Current Figure 8. Voltage Ripple vs. Output Current
Figure 9. Power Dissipation vs. Output Current Figure 10. Safe Operating Area
Figure 11. VOUT= 5 V, IOUT= 2 A, COUT1= 44 µF ceramic,
COUT2= 56 µF electrolytic, fSW= 500 kHz Figure 12. VOUT= 12 V, IOUT= 2 A, COUT1= 44 µF ceramic,
COUT2= 56 µF electrolytic, fSW= 800 kHz
0
0.5
1
1.5
2
2.5
3
3.5
4
0 0.5 1 1.5 2 2.5
Output Current (A)
Power Dissipation (W)
VOUT = 15 V, fSW = 1 MHz
VOUT = 12 V, fSW = 800 kHz
VOUT = 5.0 V, fSW = 500 kHz
VOUT = 3.3 V, fSW = 400 kHz
VOUT = 2.5 V, fSW = 400 kHz
G000
20
30
40
50
60
70
80
90
0 0.5 1 1.5 2 2.5
Output Current (A)
Ambient Temperature (°C)
VO = 5 V
VO = 12 V
VO = 15 V
Natural Convection
G000
50
55
60
65
70
75
80
85
90
95
100
0 0.5 1 1.5 2 2.5
Output Current (A)
Efficiency (%)
VOUT = 15 V, fSW = 1 MHz
VOUT = 12 V, fSW = 800 kHz
VOUT = 5.0 V, fSW = 500 kHz
VOUT = 3.3 V, fSW = 400 kHz
VOUT = 2.5 V, fSW = 400 kHz
G000
0
10
20
30
40
50
60
0 0.5 1 1.5 2 2.5
Output Current (A)
Output Voltage Ripple (mV)
VOUT = 15 V, fSW = 1 MHz
VOUT = 12 V, fSW = 800 kHz
VOUT = 5.0 V, fSW = 500 kHz
VOUT = 3.3 V, fSW = 400 kHz
VOUT = 2.5 V, fSW = 400 kHz
G000
10
LMZ35003
SNVS988B –JULY 2013–REVISED APRIL 2018
www.ti.com
Product Folder Links: LMZ35003
Submit Documentation Feedback Copyright © 2013–2018, Texas Instruments Incorporated
8 Typical Characteristics (VIN = 36 V)
The electrical characteristic data has been developed from actual products tested at 25°C. This data is considered typical for
the converter. Applies to Figure 13,Figure 14, and Figure 15. At light load the output voltage ripple may increase due to pulse
skipping. See Light-Load Behavior for more information. Applies to Figure 14. The temperature derating curves represent the
conditions at which internal components are at or below the manufacturer's maximum operating temperatures. Derating limits
apply to devices soldered directly to a 100 mm × 100 mm double-sided PCB with 1 oz. copper. Applies to Figure 16.
Figure 13. Efficiency vs. Output Current Figure 14. Voltage Ripple vs. Output Current
Figure 15. Power Dissipation vs. Output Current Figure 16. Safe Operating Area
Figure 17. VOUT= 5 V, IOUT= 2 A, COUT1= 44 µF ceramic,
COUT2= 56 µF electrolytic, fSW= 500 kHz Figure 18. VOUT= 12 V, IOUT= 2 A, COUT1= 44 µF ceramic,
COUT2= 56 µF electrolytic, fSW= 800 kHz
0
1
2
3
4
5
6
0 0.5 1 1.5 2 2.5
Output Current (A)
Power Dissipation (W)
VOUT = 15 V, fSW = 1 MHz
VOUT = 12 V, fSW = 800 kHz
VOUT = 5.0 V, fSW = 500 kHz
VOUT = 3.3 V, fSW = 400 kHz
G000
20
30
40
50
60
70
80
90
0 0.5 1 1.5 2 2.5
Output Current (A)
Ambient Temperature (°C)
VO = 5 V
VO = 12 V
VO = 15 V
Natural Convection
G000
50
55
60
65
70
75
80
85
90
95
100
0 0.5 1 1.5 2 2.5
Output Current (A)
Efficiency (%)
VOUT = 15 V, fSW = 1 MHz
VOUT = 12 V, fSW = 800 kHz
VOUT = 5.0 V, fSW = 500 kHz
VOUT = 3.3 V, fSW = 400 kHz
G000
0
10
20
30
40
50
60
70
0 0.5 1 1.5 2 2.5
Output Current (A)
Output Voltage Ripple (mV)
VOUT = 15 V, fSW = 1 MHz
VOUT = 12 V, fSW = 800 kHz
VOUT = 5.0 V, fSW = 500 kHz
VOUT = 3.3 V, fSW = 400 kHz
G000
11
LMZ35003
www.ti.com
SNVS988B –JULY 2013–REVISED APRIL 2018
Product Folder Links: LMZ35003
Submit Documentation FeedbackCopyright © 2013–2018, Texas Instruments Incorporated
9 Typical Characteristics (VIN = 48 V)
The electrical characteristic data has been developed from actual products tested at 25°C. This data is considered typical for
the converter. Applies to Figure 19,Figure 20, and Figure 21. At light load the output voltage ripple may increase due to pulse
skipping. See Light-Load Behavior for more information. Applies to Figure 20. The temperature derating curves represent the
conditions at which internal components are at or below the manufacturer's maximum operating temperatures. Derating limits
apply to devices soldered directly to a 100 mm × 100 mm double-sided PCB with 1 oz. copper. Applies to Figure 22.
Figure 19. Efficiency vs. Output Current Figure 20. Voltage Ripple vs. Output Current
Figure 21. Power Dissipation vs. Output Current Figure 22. Safe Operating Area
Figure 23. VOUT= 5 V, IOUT= 2 A, COUT1= 44 µF ceramic,
COUT2= 56 µF electrolytic, fSW= 500 kHz Figure 24. VOUT= 12 V, IOUT= 2 A, COUT1= 44 µF ceramic,
COUT2= 56 µF electrolytic, fSW= 800 kHz
12
LMZ35003
SNVS988B –JULY 2013–REVISED APRIL 2018
www.ti.com
Product Folder Links: LMZ35003
Submit Documentation Feedback Copyright © 2013–2018, Texas Instruments Incorporated
(1) Capacitor Supplier Verification, RoHS, Lead-free and Material Details
Consult capacitor suppliers regarding availability, material composition, RoHS and lead-free status, and manufacturing process
requirements for any capacitors identified in this table.
(2) Maximum ESR @ 100 kHz, 25°C.
10 Capacitor Recommendations for the LMZ35003 Power Supply
10.1 Capacitor Technologies
10.1.1 Electrolytic, Polymer-Electrolytic Capacitors
When using electrolytic capacitors, high-quality, computer-grade electrolytic capacitors are recommended.
Polymer-electrolytic type capacitors are recommended for applications where the ambient operating temperature
is less than 0°C. The Sanyo OS-CON capacitor series is suggested due to the lower ESR, higher rated surge,
power dissipation, ripple current capability, and small package size. Aluminum electrolytic capacitors provide
adequate decoupling over the frequency range of 2 kHz to 150 kHz, and are suitable when ambient temperatures
are above 0°C.
10.1.2 Ceramic Capacitors
The performance of aluminum electrolytic capacitors is less effective than ceramic capacitors above 150 kHz.
Multilayer ceramic capacitors have a low ESR and a resonant frequency higher than the bandwidth of the
regulator. They can be used to reduce the reflected ripple current at the input as well as improve the transient
response of the output.
10.1.3 Tantalum, Polymer-Tantalum Capacitors
Polymer-tantalum type capacitors are recommended for applications where the ambient operating temperature is
less than 0°C. The Sanyo POSCAP series and Kemet T530 capacitor series are recommended rather than many
other tantalum types due to their lower ESR, higher rated surge, power dissipation, ripple current capability, and
small package size. Tantalum capacitors that have no stated ESR or surge current rating are not recommended
for power applications.
10.2 Input Capacitor
The LMZ35003 requires a minimum input capacitance of 4.4 μF of ceramic type. The voltage rating of input
capacitors must be greater than the maximum input voltage. The ripple current rating of the capacitor must be at
least 450 mArms. Table 3 includes a preferred list of capacitors by vendor.
10.3 Output Capacitor
The output capacitance of the LMZ35003 can be comprised of either all ceramic capacitors, or a combination of
ceramic and bulk capacitors. The required output capacitance must include at least 100 µF of ceramic type (or 2
x 47 µF). When adding additional non-ceramic bulk capacitors, low-ESR devices like the ones recommended in
Table 3 are required. Additional capacitance above the minimum is determined by actual transient deviation
requirements. Table 3 includes a preferred list of capacitors by vendor.
Table 3. Recommended Input/Output Capacitors(1)
VENDOR SERIES PART NUMBER
CAPACITOR CHARACTERISTICS
WORKING
VOLTAGE
(V)
CAPACITANCE
(µF) ESR (2)
(mΩ)
Murata X5R GRM31CR61H225KA88L 50 4.7 2
TDK X5R C3216X5R1H475K 50 4.7 2
Murata X5R GRM32ER61E226K 16 22 2
TDK X5R C3225X5R0J476K 6.3 47 2
Murata X5R GRM32ER60J476M 6.3 47 2
Sanyo POSCAP 16TQC68M 16 68 50
Sanyo POSCAP 6TPE100MI 6.3 100 25
Kemet T530 T530D227M006ATE006 6.3 220 6
VOUT
VIN
LMZ35003
VADJ
AGND PGND
V
OUT
V
IN
PWRGD
RT/CLK
INH/UVLO
COMP
STSEL
C
IN1
R
SET
C
OUT1
R
UVLO1
R
UVLO2
C
OUT2
C
IN2
R
RT
SS/TR
13
LMZ35003
www.ti.com
SNVS988B –JULY 2013–REVISED APRIL 2018
Product Folder Links: LMZ35003
Submit Documentation FeedbackCopyright © 2013–2018, Texas Instruments Incorporated
11 Application Information
11.1 LMZ35003 Operation
The LMZ35003 can operate over a wide input voltage range of 7 V to 50 V and produce output voltages from 2.5
V to 15 V. The performance of the device varies over this wide operating range, and there are some important
considerations when operated near the boundary limits. This section offers guidance in selecting the optimum
components depending on the application and operating conditions.
The user must select three primary parameters when designing with the LMZ35003.
• Output Voltage
• UVLO Threshold
• Switching Frequency
The adjustment of each of these parameters can be made using just one or two resistors. Figure 25 below shows
a typical LMZ35003 schematic with the key parameter-setting resistors labeled.
Figure 25. LMZ35003 Typical Schematic
( )
æ ö
= ´ - W
ç ÷
è ø
OUT
SET
V
R 10 1 k
0.798
14
LMZ35003
SNVS988B –JULY 2013–REVISED APRIL 2018
www.ti.com
Product Folder Links: LMZ35003
Submit Documentation Feedback Copyright © 2013–2018, Texas Instruments Incorporated
11.2 Adjusting the Output Voltage
The LMZ35003 is designed to provide output voltages from 2.5V to 15V. The output voltage is determined by the
value of RSET, which must be connected between the VOUT node and the VADJ pin (Pin 36). For output voltages
greater than 5.0V, improved operating performance can be obtained by increasing the operating frequency. This
adjustment requires the addition of RRT between RT/CLK (Pin 31) and AGND (Pin 30). See the Switching
Frequency section for more details. Table 4 gives the standard external RSET resistor for a number of common
bus voltages and also includes the recommended RRT resistor for output voltages above 5.0V.
Table 4. Standard RSET Resistor Values for Common Output Voltages
RESISTORS
OUTPUT VOLTAGE VOUT (V)
2.5 3.3 5.0 8.0 12.0 15.0
RSET (kΩ)21.5 31.6 52.3 90.9 140 178
RRT (kΩ)open open 1100 549 267 178
For other output voltages the value of RSET can be calculated using the following formula, or simply selected from
the range of values given in Table 5.
(1)
Table 5. Standard RSET and RRT Resistor Values
VOUT (V) RSET (kΩ) RRT(kΩ) fSW(kHz) VOUT (V) RSET (kΩ) RRT(kΩ) fSW(kHz)
2.5 21.5 open 400 9.0 102 365 700
3.0 27.4 open 400 9.5 110 365 700
3.3 31.6 open 400 10.0 115 365 700
3.5 34.0 open 400 10.5 121 267 800
4.0 40.2 open 400 11.0 127 267 800
4.5 46.4 open 400 11.5 133 267 800
5.0 52.3 1100 500 12.0 140 267 800
5.5 48.7 1100 500 12.5 147 215 900
6.0 64.9 1100 500 13.0 154 215 900
6.5 71.5 1100 500 13.5 158 215 900
7.0 78.7 549 600 14.0 165 178 1000
7.5 84.5 549 600 14.5 174 178 1000
8.0 90.9 549 600 15.0 178 178 1000
8.5 97.6 365 700
11.3 Input Voltage
The LMZ35003 operates over the input voltage range of 7 V to 50 V. For reliable start-up and operation at light
loads, the minimum input voltage depends on the output voltage. For output voltages ≤12V, the minimum input
voltage is 7V or (VOUT + 3V), whichever is greater. For output voltages > 12V, the minimum input voltage is
(1.33 x VOUT).
The maximum input voltage is (15 x VOUT) or 50 V, whichever is less.
While the device can safely handle input surge voltages up to 65 V, sustained operation at input voltages above
50 V is not recommended.
See the Undervoltage Lockout (UVLO) Threshold section of this datasheet for more information.
INH/UVLO
VIN
RUVLO1
RUVLO2
AGND
VIN
( ) ( )
-
= W
æ ö
-+ ´
ç ÷
ç ÷
è ø
UVLO2
ON 3
UVLO1
1.25
R k
V 1.25
0.9 10
R
( ) ( )
-
-
= W
´
ON OFF
UVLO1 3
V V
R k
2.9 10
15
LMZ35003
www.ti.com
SNVS988B –JULY 2013–REVISED APRIL 2018
Product Folder Links: LMZ35003
Submit Documentation FeedbackCopyright © 2013–2018, Texas Instruments Incorporated
11.4 Undervoltage Lockout (UVLO) Threshold
At turn-on, the VON UVLO threshold determines the input voltage level where the device begins power
conversion. During the power-down sequence, the VOFF UVLO threshold determines the input voltage where
power conversion ceases. The turn-on and turn-off thresholds are set by two resistors, RUVLO1 and RUVLO2 as
shown in Figure 26.
The VON UVLO threshold must be set to at least (VOUT + 3 V) or 7 V whichever is greater to insure proper start-
up and reduce current surges on the host input supply as the voltage rises. If possible, it is recommended to set
the UVLO threshold to appproximantely 80 to 85% of the minimum expected input voltage.
Use Equation 2 and Equation 3 to calculate the values of RUVLO1 and RUVLO2. VON is the voltage threshold during
power-up when the input voltage is rising. VOFF is the voltage threshold during power-down when the input
voltage is decreasing. VOFF should be selected to be at least 500mV less than VON.Table 6 lists standard resistor
values for RUVLO1 and RUVLO2 for adjusting the VON UVLO threshold for several input voltages.
(2)
(3)
Figure 26. Adjustable VIN UVLO
Table 6. Standard Resistor Values to set VON UVLO Threshold
VON THRESHOLD (V) 6.5 10.0 15.0 20.0 25.0 30.0 35.0 40.0 45.0
RUVLO1 (kΩ)174 174 174 174 174 174 174 174 174
RUVLO2 (kΩ)40.2 24.3 15.8 11.5 9.09 7.50 6.34 5.62 4.99
11.5 Power Good (PWRGD)
The PWRGD pin is an open drain output. Once the output voltage is between 94% and 106% of the set voltage,
the PWRGD pin pull-down is released and the pin floats. The recommended pull-up resistor value is between 10
kΩand 100 kΩto a voltage source that is 5.5 V or less. The PWRGD pin is in a defined state once VIN is
greater than 1.0 V, but with reduced current sinking capability. The PWRGD pin achieves full current sinking
capability once the VIN pin is above 4.5V. The PWRGD pin is pulled low when the output voltage is lower than
91% or greater than 109% of the nominal set voltage. Also, the PWRGD pin is pulled low if the input UVLO or
thermal shutdown is asserted, the INH pin is pulled low, or the SS/TR pin is below 1.4 V.
16
LMZ35003
SNVS988B –JULY 2013–REVISED APRIL 2018
www.ti.com
Product Folder Links: LMZ35003
Submit Documentation Feedback Copyright © 2013–2018, Texas Instruments Incorporated
11.6 Switching Frequency
Nominal switching frequency of the LMZ35003 is set from the factory at 400 kHz. This switching frequency is
optimum for output voltages below 5.0 V. For output voltages 5.0V and above, better operating performance can
be obtained raising the operating frequency. This is easily done by adding a resistor, RRT in , from the RT/CLK
pin (Pin 31) to the AGND pin (Pin 30). Raising the operating frequency reduces output voltage ripple, lowers the
load current threshold where pulse skipping begins, and improves transient response.
The recommended switching frequency for all output voltages is listed in Table 5.
For the maximum recommended output voltage value of 15 V, the switching frequency computes to 1000 kHz or
1 MHz. Operation above 1 MHz is not recommended. Use Table 7 below to select the value of the timing resistor
for the given values of switching frequencies.
Table 7. Standard Resistor Values to set the Switching Frequency
fSW (kHz) 400 500 600 700 800 900 1000
RRT(kΩ)OPEN 1100 549 365 267 215 178
It is also possible to synchronize the switching frequency to an external clock signal. See the Synchronization
(CLK) section for further details.
While it is possible to set the operating frequency higher than 400 kHz when using the device at output voltages
of 5 V or less, minimum duty cycle and pulse skipping issues restrict the maximum recommended input voltage
under these conditions. The recommended operating conditions for the LMZ35003 can be summarized by
Figure 27. The graph shows the maximum input voltage vs. output voltage restriction for several operating
frequencies. The lower boundary of the graph shows the minimum input voltage as a function of the output
voltage.
Figure 27. Optimum Operating Range with Switching Frequency
VOUT
VIN
LMZ35003
VADJ
AGND PGND
V
OUT
12 V @ 2.5 A
V
IN
15-50 V
PWRGD
RT/CLK
INH/UVLO
STSEL
2.2 F
100 V
140kΩ
47 F
16 V
174kΩ
15.4kΩ
SS/TR 267kΩ
47 F
16 V
22 nF
2.2 F
100 V
VOUT
VIN
LMZ35003
VADJ
AGND PGND
V
OUT
3.3V @ 2.5A
V
IN
7-36 V
PWRGD
RT/CLK
INH/UVLO
STSEL
4.7 F
50 V
31.6kΩ
47 F
6.3 V
174kΩ
40.2kΩ
SS/TR
47 F
6.3 V
17
LMZ35003
www.ti.com
SNVS988B –JULY 2013–REVISED APRIL 2018
Product Folder Links: LMZ35003
Submit Documentation FeedbackCopyright © 2013–2018, Texas Instruments Incorporated
11.7 Application Schematics
Figure 28. Typical Schematic
VIN = 7 V to 36 V, VOUT = 3.3 V
Figure 29. Typical Schematic
VIN = 15 V to 50 V, VOUT = 12 V
VOUT
VIN
LMZ35003
VADJ
AGND PGND
V
OUT
5 V @ 2.5 A
V
IN
8-50 V
PWRGD
RT/CLK
INH/UVLO
STSEL
2.2 F
100 V
52.3kΩ
47 F
6.3 V
174kΩ
31.6kΩ
SS/TR 1100kΩ
47 F
6.3 V
2.2 F
100 V
18
LMZ35003
SNVS988B –JULY 2013–REVISED APRIL 2018
www.ti.com
Product Folder Links: LMZ35003
Submit Documentation Feedback Copyright © 2013–2018, Texas Instruments Incorporated
Application Schematics (continued)
Figure 30. Typical Schematic
VIN=8Vto50V,VOUT=5V
19
LMZ35003
www.ti.com
SNVS988B –JULY 2013–REVISED APRIL 2018
Product Folder Links: LMZ35003
Submit Documentation FeedbackCopyright © 2013–2018, Texas Instruments Incorporated
11.8 Custom Design With WEBENCH® Tools
Click here to create a custom design using the LMZ35003 device with the WEBENCH® Power Designer.
1. Start by entering the input voltage (VIN), output voltage (VOUT), and output current (IOUT) requirements.
2. Optimize the design for key parameters such as efficiency, footprint, and cost using the optimizer dial.
3. Compare the generated design with other possible solutions from Texas Instruments.
The WEBENCH Power Designer provides a customized schematic along with a list of materials with real-time
pricing and component availability.
In most cases, these actions are available:
• Run electrical simulations to see important waveforms and circuit performance
• Run thermal simulations to understand board thermal performance
• Export customized schematic and layout into popular CAD formats
• Print PDF reports for the design, and share the design with colleagues
Get more information about WEBENCH tools at www.ti.com/WEBENCH.
11.9 Power-Up Characteristics
When configured as shown in the front page schematic, the LMZ35003 produces a regulated output voltage
following the application of a valid input voltage. During the power-up, internal soft-start circuitry slows the rate
that the output voltage rises, thereby limiting the amount of in-rush current that can be drawn from the input
source. The soft-start circuitry introduces a short time delay from the point that a valid input voltage is
recognized. Figure 31 shows the start-up waveforms for a LMZ35003, operating from a 24-V input and the output
voltage adjusted to 5 V. The waveform were measured with a 2-A constant current load.
Figure 31. Start-Up Sequence
Q1
INH
Control
INH/UVLO
VIN
RUVLO1
RUVLO2
AGND
VIN
20
LMZ35003
SNVS988B –JULY 2013–REVISED APRIL 2018
www.ti.com
Product Folder Links: LMZ35003
Submit Documentation Feedback Copyright © 2013–2018, Texas Instruments Incorporated
11.10 Output On/Off Inhibit (INH)
The INH pin provides electrical on/off control of the device. Once the INH pin voltage exceeds the threshold
voltage, the device starts operation. If the INH pin voltage is pulled below the threshold voltage, the regulator
stops switching and enters low quiescent current state.
The INH pin has an internal pull-up current source, allowing the user to float the INH pin for enabling the device.
If an application requires controlling the INH pin, use an open drain/collector device, or a suitable logic gate to
interface with the pin.
Figure 32 shows the typical application of the inhibit function. The Inhibit control has its own internal pull-up to
VIN potential. An open-collector or open-drain device is recommended to control this input.
Turning Q1 on applies a low voltage to the inhibit control (INH) pin and disables the output of the supply, shown
in Figure 33. If Q1 is turned off, the supply executes a soft-start power-up sequence, as shown in Figure 34. A
regulated output voltage is produced within 5 ms. The waveforms were measured with a 2-A constant current
load.
Figure 32. Typical Inhibit Control
Figure 33. Inhibit Turn-Off Figure 34. Inhibit Turn-On
SS/TR
STSELAGND
CSS
(Optional)
21
LMZ35003
www.ti.com
SNVS988B –JULY 2013–REVISED APRIL 2018
Product Folder Links: LMZ35003
Submit Documentation FeedbackCopyright © 2013–2018, Texas Instruments Incorporated
11.11 Slow Start (SS/TR)
For outputs voltages of 5V or less, the slow start capacitance built into the LMZ35003 is sufficient to provide for a
turn-on ramp rate that does not induce large surge currents while charging the output capacitors. Connecting the
STSEL pin (Pin 29) to AGND while leaving SS pin (Pin 28) open enables the internal SS capacitor with a slow
start interval of approximately 5 ms. For output voltages greater than 5V, additional slow start capacitance is
recommended. For 12V to 15V output voltages, a 22nF capacitor should be connected between the SS/TR pin
(Pin 28) and AGND, while connecting the STSEL pin (Pin 29) to AGND as well. Figure 35 shows an additional
SS capacitor connected to the SS pin and the STSEL pin connected to AGND. See Table 8 below for SS
capacitor values and timing interval.
Figure 35. Slow Start Capacitor (CSS) and STSEL Connection
Table 8. Slow Start Capacitor Values and Slow Start Time
CSS (nF) open 4.7 10 15 22
SS Time (msec) 5 7 10 13 17
CONT
DIS
TLC555
OUT
RST
GND
THRS
TRIG
VDD
1 F
47.5kΩ
100kΩ 100kΩ
475kΩ
3.3V/5V
3.3V/5V
To INH/UVLO
Pin 27
From PWRGD
Pin 35
BSS138
BSS138
22
LMZ35003
SNVS988B –JULY 2013–REVISED APRIL 2018
www.ti.com
Product Folder Links: LMZ35003
Submit Documentation Feedback Copyright © 2013–2018, Texas Instruments Incorporated
11.12 Overcurrent Protection
For protection against load faults, the LMZ35003 incorporates cycle-by-cycle current limiting. During an
overcurrent condition the output current is limited and the output voltage is reduced, as shown in Figure 36. As
the output voltage drops more than 8% below the set point, the PWRGD signal is pulled low. If the output voltage
drops more than 25%, the switching frequency is reduced to reduce power dissipation within the device. When
the overcurrent condition is removed, the output voltage returns to the established voltage.
The LMZ35003 is not designed to endure a sustained short circuit condition. The use of an output fuse, voltage
supervisor circuit, or other overcurrent protection circuit is recommended. A recommended overcurrent protection
circuit is shown in Figure 37. This circuit uses the PWRGD signal as an indication of an overcurrent condition. As
PWRGD remains low, the 555 timer operates as a low frequency oscillator, driving the INH/UVLO pin low for
approximately 400ms, halting the power conversion of the device. After the inhibit interval, the INH/UVLO pin is
released and the LMZ35003 restarts. If the overcurrent condition is removed, the PWRGD signal goes high,
resetting the oscillator and power conversion resumes, otherwise the inhibit cycle repeats.
Figure 36. Overcurrent Limiting
Figure 37. Over-Current Protection Circuit
AGND
RT/CLK
R
RT
External Clock
300 kHz to 1 MHz
1 kΩ
470 pF
0
100
200
300
400
500
600
700
800
900
10 15 20 25 30 35 40 45 50
Input Voltage (V)
Output Current (mA)
2.5 V, 400 kHz
3.3 V, 400 kHz
5.0 V, 400 kHz
9 V, 600 kHz
12 V, 800 kHz
15 V, 1 MHz
G000
23
LMZ35003
www.ti.com
SNVS988B –JULY 2013–REVISED APRIL 2018
Product Folder Links: LMZ35003
Submit Documentation FeedbackCopyright © 2013–2018, Texas Instruments Incorporated
11.13 Light-Load Behavior
The LMZ35003 is a non-synchronous converter. One of the characteristics of a non-synchronous converter is
that as the load current on the output is decreased, a point is reached where the energy delivered by a single
switching pulse is more than the load can absorb. This causes the output voltage to rise slightly. This rise in
output voltage is sensed by the feedback loop and the device responds by skipping one or more switching cycles
until the output voltages falls back to the set point. At very light loads or no load, many switching cycles are
skipped. The observed effect during this pulse skipping mode of operation is an increase in the peak to peak
ripple voltage, and a decrease in the ripple frequency. The load current where pulse skipping begins is a function
of the input voltage, the output voltage, and the switching frequency. A plot of the pulse skipping threshold
current as a function of input voltage is given in Figure 38 for a number of popular output voltage and switching
frequency combinations.
Figure 38. Pulse Skipping Threshold
11.14 Synchronization (CLK)
An internal phase locked loop (PLL) allows synchronization between 400 kHz and 1 MHz, and to easily switch
from RT mode to CLK mode. To implement the synchronization feature, connect a square wave clock signal to
the RT/CLK pin with a duty cycle between 20% to 80%. The clock signal amplitude must transition lower than 0.8
V and higher than 2.0 V. The start of the switching cycle is synchronized to the falling edge of RT/CLK pin. In
applications where both RT mode and CLK mode are needed, the device can be configured as shown in
Figure 39.
Before the external clock is present, the device works in RT mode where the switching frequency is set by the
RRT resistor. When the external clock is present, the CLK mode overrides the RT mode. The first time the CLK
pin is pulled above the RT/CLK high threshold (2.0 V), the device switches from RT mode to CLK mode and the
RT/CLK pin becomes high impedance as the PLL starts to lock onto the frequency of the external clock. It is not
recommended to switch from CLK mode back to RT mode because the internal switching frequency drops to 100
kHz first before returning to the switching frequency set by the RRT resistor .
Figure 39. CLK/RT Configuration
PGND
Plane
R
SET
VOUT sense
Via
LOAD
VOUT sense
Via
Thermal
Vias
AGND
VOUTPGND
COUT1
VIN
PH
COUT2
CIN1
AGND to PGND
Connection
24
LMZ35003
SNVS988B –JULY 2013–REVISED APRIL 2018
www.ti.com
Product Folder Links: LMZ35003
Submit Documentation Feedback Copyright © 2013–2018, Texas Instruments Incorporated
11.15 Thermal Shutdown
The internal thermal shutdown circuitry forces the device to stop switching if the junction temperature exceeds
180°C typically. The device reinitiates the power up sequence when the junction temperature drops below 165°C
typically.
11.16 Layout Considerations
To achieve optimal electrical and thermal performance, an optimized PCB layout is required. Figure 40 and
Figure 41 show two layers of a typical PCB layout. Some considerations for an optimized layout are:
• Use large copper areas for power planes (VIN, VOUT, and PGND) to minimize conduction loss and thermal
stress.
• Place ceramic input and output capacitors close to the module pins to minimize high frequency noise.
• Locate additional output capacitors between the ceramic capacitor and the load.
• Place a dedicated AGND copper area beneath the LMZ35003.
• Isolate the PH copper area from the VOUT copper area using the PGND copper area.
• Connect the AGND and PGND copper area at one point; at pins 8 & 9.
• Place RSET, RRT, and CSS as close as possible to their respective pins.
• Use multiple vias to connect the power planes to internal layers.
• Use a dedicated sense line to connect RSET to VOUT near the load for best regulation.
Figure 40. Typical Top-Layer Recommended Layout Figure 41. Typical PGND-Layer Recommended Layout
25
LMZ35003
www.ti.com
SNVS988B –JULY 2013–REVISED APRIL 2018
Product Folder Links: LMZ35003
Submit Documentation FeedbackCopyright © 2013–2018, Texas Instruments Incorporated
11.17 EMI
The LMZ35003 is compliant with EN55022 Class B radiated emissions. Figure 42 and Figure 43 show typical
examples of radiated emissions plots for the LMZ35003 operating from 24 V and 12 V respectively. Both graphs
include the plots of the antenna in the horizontal and vertical positions.
Figure 42. Radiated Emissions 24-V Input, 5-V Output, 2-A
Load (EN55022 Class B) Figure 43. Radiated Emissions 12-V Input, 5-V Output, 2-A
Load (EN55022 Class B)
26
LMZ35003
SNVS988B –JULY 2013–REVISED APRIL 2018
www.ti.com
Product Folder Links: LMZ35003
Submit Documentation Feedback Copyright © 2013–2018, Texas Instruments Incorporated
12 Revision History
Changes from Revision A (June 2017) to Revision B Page
• Added WEBENCH® design links for the LMZ35003.............................................................................................................. 1
• Increased the peak reflow temperature and maximum number of reflows to JEDEC specifications for improved
manufacturability .................................................................................................................................................................... 2
• Added Device and Documentation Support section ............................................................................................................ 27
• Added Mechanical, Packaging, and Orderable Information section..................................................................................... 28
Changes from Original (July 2013) to Revision A Page
• Deleted graphic above title .................................................................................................................................................... 1
• Added peak reflow and maximum number of reflows information ........................................................................................ 2
27
LMZ35003
www.ti.com
SNVS988B –JULY 2013–REVISED APRIL 2018
Product Folder Links: LMZ35003
Submit Documentation FeedbackCopyright © 2013–2018, Texas Instruments Incorporated
13 Device and Documentation Support
13.1 Device Support
13.1.1 Development Support
13.1.1.1 Custom Design With WEBENCH® Tools
Click here to create a custom design using the LMZ35003 device with the WEBENCH® Power Designer.
1. Start by entering the input voltage (VIN), output voltage (VOUT), and output current (IOUT) requirements.
2. Optimize the design for key parameters such as efficiency, footprint, and cost using the optimizer dial.
3. Compare the generated design with other possible solutions from Texas Instruments.
The WEBENCH Power Designer provides a customized schematic along with a list of materials with real-time
pricing and component availability.
In most cases, these actions are available:
• Run electrical simulations to see important waveforms and circuit performance
• Run thermal simulations to understand board thermal performance
• Export customized schematic and layout into popular CAD formats
• Print PDF reports for the design, and share the design with colleagues
Get more information about WEBENCH tools at www.ti.com/WEBENCH.
13.2 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
13.3 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
13.4 Trademarks
E2E is a trademark of Texas Instruments.
WEBENCH is a registered trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
13.5 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
13.6 Glossary
SLYZ022 —TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
Reel Width (W1)
REEL DIMENSIONS
A0
B0
K0
W
Dimension designed to accommodate the component length
Dimension designed to accommodate the component thickness
Overall width of the carrier tape
Pitch between successive cavity centers
Dimension designed to accommodate the component width
TAPE DIMENSIONS
K0 P1
B0 W
A0
Cavity
QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE
Pocket Quadrants
Sprocket Holes
Q1 Q1
Q2 Q2
Q3 Q3Q4 Q4
Reel
Diameter
User Direction of Feed
P1
28
LMZ35003
SNVS988B –JULY 2013–REVISED APRIL 2018
www.ti.com
Product Folder Links: LMZ35003
Submit Documentation Feedback Copyright © 2013–2018, Texas Instruments Incorporated
14 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
14.1 Tape and Reel Information
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width W1
(mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LMZ35003RKGR B1QFN RKG 41 500 330.0 24.4 9.35 11.35 3.1 16.0 24.0 Q1
LMZ35003RKGT B1QFN RKG 41 250 330.0 24.4 9.35 11.35 3.1 16.0 24.0 Q1
TAPE AND REEL BOX DIMENSIONS
Width (mm)
W
L
H
29
LMZ35003
www.ti.com
SNVS988B –JULY 2013–REVISED APRIL 2018
Product Folder Links: LMZ35003
Submit Documentation FeedbackCopyright © 2013–2018, Texas Instruments Incorporated
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LMZ35003RKGR B1QFN RKG 41 500 383.0 353.0 58.0
LMZ35003RKGT B1QFN RKG 41 250 383.0 353.0 58.0
PACKAGE OPTION ADDENDUM
www.ti.com 4-Jun-2020
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LMZ35003RKGR ACTIVE B1QFN RKG 41 500 RoHS Exempt
& Green NIPDAU Level-3-250C-168 HR -40 to 85 (54260, LMZ35003)
LMZ35003RKGT ACTIVE B1QFN RKG 41 250 RoHS Exempt
& Green NIPDAU Level-3-250C-168 HR -40 to 85 (54260, LMZ35003)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
PACKAGE OPTION ADDENDUM
www.ti.com 4-Jun-2020
Addendum-Page 2
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LMZ35003RKGR B1QFN RKG 41 500 330.0 24.4 9.35 11.35 3.1 16.0 24.0 Q1
LMZ35003RKGT B1QFN RKG 41 250 330.0 24.4 9.35 11.35 3.1 16.0 24.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 10-Mar-2021
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LMZ35003RKGR B1QFN RKG 41 500 383.0 353.0 58.0
LMZ35003RKGT B1QFN RKG 41 250 383.0 353.0 58.0
PACKAGE MATERIALS INFORMATION
www.ti.com 10-Mar-2021
Pack Materials-Page 2
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party
intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages,
costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (https:www.ti.com/legal/termsofsale.html) or other applicable terms available either
on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s
applicable warranties or warranty disclaimers for TI products.IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2021, Texas Instruments Incorporated