Document Number: 91044 www.vishay.com
S11-1048-Rev. C, 30-May-11 1
This document is subject to change without notice.
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
Power MOSFET
IRF720S, SiHF720S
Vishay Siliconix
FEATURES
Halogen-free According to IEC 61249-2-21
Definition
Surface Mount
Available in Tape and Reel
Dynamic dV/dt Rating
Repetitive Avalanche Rated
•Fast Switching
Ease of Paralleling
Simple Drive Requirements
Compliant to RoHS Directive 2002/95/EC
DESCRIPTION
Third generation Power MOSFETs from Vishay provide the
designer with the best combination of fast switching,
ruggedized device design, low on-resistance and
cost-effectiveness.
The D2PAK (TO-263) is a surface mount power package
capable of accommodating die size up to HEX-4. It provides
the highest power capability and the lowest possible
on-resistance in any existing surface mount package. The
D2PAK (TO-263) is suitable for high current applications
because of its low internal connection resistance and can
dissipate up to 2.0 W in a typical surface mount application.
Note
a. See device orientation.
Notes
a. Repetitive rating; pulse width limited by maximum junction temperature (see fig. 11).
b. VDD = 50 V, starting TJ = 25 °C, L = 30 mH, Rg = 25 , IAS = 3.3 A (see fig. 12).
c. ISD 3.3 A, dI/dt 65 A/μs, VDD VDS, TJ 150 °C.
d. 1.6 mm from case.
e. When mounted on 1" square PCB (FR-4 or G-10 material).
PRODUCT SUMMARY
VDS (V) 400
RDS(on) ()V
GS = 10 V 1.8
Qg (Max.) (nC) 20
Qgs (nC) 3.3
Qgd (nC) 11
Configuration Single
N-Channel MOSFET
G
D
S
D
2
PAK (TO-263)
GD
S
ORDERING INFORMATION
Package D2PAK (TO-263) D2PAK (TO-263) D2PAK (TO-263)
Lead (Pb)-free and Halogen-free SiHF720S-GE3 SiHF720STRR-GE3aSiHF720STRL-GE3a
Lead (Pb)-free IRF720SPbF IRF720STRRPbFa -
SiHF720S-E3 SiHF720STR-E3a-
ABSOLUTE MAXIMUM RATINGS (TC = 25 °C, unless otherwise noted)
PARAMETER SYMBOL LIMIT UNIT
Drain-Source Voltage VDS 400 V
Gate-Source Voltage VGS ± 20
Continuous Drain Current VGS at 10 V TC = 25 °C ID
3.3
ATC = 100 °C 2.1
Pulsed Drain CurrentaIDM 13
Linear Derating Factor 0.40 W/°C
Linear Derating Factor (PCB Mount)e0.025
Single Pulse Avalanche EnergybEAS 190 mJ
Avalanche CurrentaIAR 3.3 A
Repetitive Avalanche EnergyaEAR 5.0 mJ
Maximum Power Dissipation TC = 25 °C PD
50 W
Maximum Power Dissipation (PCB Mount)eTA = 25 °C 3.1
Peak Diode Recovery dV/dtcdV/dt 4.0 V/ns
Operating Junction and Storage Temperature Range TJ, Tstg - 55 to + 150 °C
Soldering Recommendations (Peak Temperature) for 10 s 300d
* Pb containing terminations are not RoHS compliant, exemptions may apply
www.vishay.com Document Number: 91044
2S11-1048-Rev. C, 30-May-11
This document is subject to change without notice.
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
IRF720S, SiHF720S
Vishay Siliconix
Note
a. When mounted on 1" square PCB (FR-4 or G-10 material).
Notes
a. Repetitive rating; pulse width limited by maximum junction temperature (see fig. 11).
b. Pulse width 300 μs; duty cycle 2 %.
THERMAL RESISTANCE RATINGS
PARAMETER SYMBOL TYP. MAX. UNIT
Maximum Junction-to-Ambient RthJA -62
°C/W
Maximum Junction-to-Ambient
(PCB Mount)aRthJA -40
Maximum Junction-to-Case (Drain) RthJC -2.5
SPECIFICATIONS (TJ = 25 °C, unless otherwise noted)
PARAMETER SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT
Static
Drain-Source Breakdown Voltage VDS VGS = 0, ID = 250 μA 400 - - V
VDS Temperature Coefficient VDS/TJ Reference to 25 °C, ID = 1 mA - 0.51 - V/°C
Gate-Source Threshold Voltage VGS(th) VDS = VGS, ID = 250 μA 2.0 - 4.0 V
Gate-Source Leakage IGSS V
GS = ± 20 V - - ± 100 nA
Zero Gate Voltage Drain Current IDSS
VDS = 400 V, VGS = 0 V - - 25 μA
VDS = 320 V, VGS = 0 V, TJ = 125 °C - - 250
Drain-Source On-State Resistance RDS(on) V
GS = 10 V ID = 2.0 Ab--1.8
Forward Transconductance gfs VDS = 50 V, ID = 2.0 Ab1.7 - - S
Dynamic
Input Capacitance Ciss VGS = 0 V,
VDS = 25 V,
f = 1.0 MHz, see fig. 5
- 410 -
pFOutput Capacitance Coss - 120 -
Reverse Transfer Capacitance Crss -47-
Total Gate Charge Qg
VGS = 10 V ID = 3.3 A, VDS = 320 V,
see fig. 6 and 13b
--20
nC Gate-Source Charge Qgs --3.3
Gate-Drain Charge Qgd --11
Turn-On Delay Time td(on)
VDD = 200 V, ID = 3.3 A,
Rg = 18 , RD = 56 , see fig. 10b
-10-
ns
Rise Time tr -14-
Turn-Off Delay Time td(off) -30-
Fall Time tf -13-
Internal Drain Inductance LD Between lead,
6 mm (0.25") from
package and center of
die contact
-4.5-
nH
Internal Source Inductance LS-7.5-
Drain-Source Body Diode Characteristics
Continuous Source-Drain Diode Current ISMOSFET symbol
showing the
integral reverse
p - n junction diode
--3.3
A
Pulsed Diode Forward CurrentaISM --13
Body Diode Voltage VSD TJ = 25 °C, IS = 3.3 A, VGS = 0 Vb--1.6V
Body Diode Reverse Recovery Time trr TJ = 25 °C, IF = 3.3 A, dI/dt = 100 A/μsb- 270 600 ns
Body Diode Reverse Recovery Charge Qrr -1.43.0μC
Forward Turn-On Time ton Intrinsic turn-on time is negligible (turn-on is dominated by LS and LD)
D
S
G
S
D
G
Document Number: 91044 www.vishay.com
S11-1048-Rev. C, 30-May-11 3
This document is subject to change without notice.
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
IRF720S, SiHF720S
Vishay Siliconix
TYPICAL CHARACTERISTICS (25 °C, unless otherwise noted)
Fig. 1 - Typical Output Characteristics, TC = 25 °C
Fig. 2 - Typical Output Characteristics, TC = 150 °C
Fig. 3 - Typical Transfer Characteristics
Fig. 4 - Normalized On-Resistance vs. Temperature
91044_01
20 µs Pulse Width
TC = 25 °C
4.5 V
VDS, Drain-to-Source Voltage (V)
ID, Drain Current (A)
100101
101
100
10-1
Bottom
To p
VGS
15 V
10 V
8.0 V
7.0 V
6.0 V
5.5 V
5.0 V
4.5 V
10-2
10-1
101
100
10-1
100101
VDS, Drain-to-Source Voltage (V)
ID, Drain Current (A)
Bottom
To p
VGS
15 V
10 V
8.0 V
7.0 V
6.0 V
5.5 V
5.0 V
4.5 V
20 µs Pulse Width
TC = 150 °C
91044_02
4.5 V
10-2
10-1
20 µs Pulse Width
VDS = 50 V
102
100
101
ID, Drain Current (A)
VGS, Gate-to-Source Voltage (V)
5678910
4
25 °C
150 °C
91044_03
I
D
= 3.3 A
V
GS
= 10 V
3.0
0.0
0.5
1.0
1.5
2.0
2.5
TJ, Junction Temperature (°C)
RDS(on), Drain-to-Source On Resistance
(Normalized)
91044_04
- 60 - 40 - 20 0 20 40 60 80 100 120 140 160
3.5
www.vishay.com Document Number: 91044
4S11-1048-Rev. C, 30-May-11
This document is subject to change without notice.
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
IRF720S, SiHF720S
Vishay Siliconix
Fig. 5 - Typical Capacitance vs. Drain-to-Source Voltage
Fig. 6 - Typical Gate Charge vs. Gate-to-Source Voltage
Fig. 7 - Typical Source-Drain Diode Forward Voltage
Fig. 8 - Maximum Safe Operating Area
1000
800
600
400
0
200
100101
Capacitance (pF)
VDS, Drain-to-Source Voltage (V)
Ciss
Crss
Coss
VGS = 0 V, f = 1 MHz
Ciss = Cgs + Cgd, Cds Shorted
Crss = Cgd
Coss = Cds + Cgd
91044_05
Q
G
, Total Gate Charge (nC)
V
GS
, Gate-to-Source Voltage (V)
20
16
12
8
0
4
0525
2015
10
V
DS
= 80 V
V
DS
= 200 V
For test circuit
see figure 13
V
DS
= 320 V
91044_06
I
D
= 3.3 A
101
100
VSD, Source-to-Drain Voltage (V)
ISD, Reverse Drain Current (A)
0.4 1.2
1.00.80.6
25 °C
150 °C
V
GS
= 0 V
91044_07
10-1
1.4
10 µs
100 µs
1 ms
10 ms
Operation in this area limited
by RDS(on)
VDS, Drain-to-Source Voltage (V)
ID, Drain Current (A)
TC = 25 °C
TJ = 150 °C
Single Pulse
10-2
102
0.1
2
5
0.1
2
5
1
2
5
10
2
5
25
125
10 25
10225
103
91044_08
Document Number: 91044 www.vishay.com
S11-1048-Rev. C, 30-May-11 5
This document is subject to change without notice.
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
IRF720S, SiHF720S
Vishay Siliconix
Fig. 9 - Maximum Drain Current vs. Case Temperature
Fig. 10a - Switching Time Test Circuit
Fig. 10b - Switching Time Waveforms
Fig. 11 - Maximum Effective Transient Thermal Impedance, Junction-to-Case
ID, Drain Current (A)
TC, Case Temperature (°C)
1.0
1.5
2.0
2.5
3.0
3.5
25 1501251007550
91044_09
0.0
0.5
Pulse width 1 µs
Duty factor 0.1 %
RD
VGS
Rg
D.U.T.
10 V
+
-
VDS
VDD
VDS
VGS
10
1
0.1
10-2
10-5 10-4 10-3 10-2 0.1 1 10
PDM
t1
t2
t1, Rectangular Pulse Duration (s)
Thermal Response (ZthJC)
Notes:
1. Duty Factor, D = t1/t2
2. Peak Tj = PDM x ZthJC + TC
Single Pulse
(Thermal Response)
0 0.5
0.2
0.1
0.05
0.02
0.01
91044_11
www.vishay.com Document Number: 91044
6S11-1048-Rev. C, 30-May-11
This document is subject to change without notice.
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
IRF720S, SiHF720S
Vishay Siliconix
Fig. 12a - Unclamped Inductive Test Circuit Fig. 12b - Unclamped Inductive Waveforms
Fig. 12c - Maximum Avalanche Energy vs. Drain Current
Fig. 13a - Basic Gate Charge Waveform Fig. 13b - Gate Charge Test Circuit
Rg
IAS
0.01 Ω
tp
D.U.T
L
VDS
+
-VDD
10 V
Vary tp to obtain
required IAS
I
AS
V
DS
V
DD
V
DS
t
p
500
0
100
200
300
400
25 150
125
10075
50
Starting T
J
, Junction Temperature (°C)
E
AS
, Single Pulse Energy (mJ)
Bottom
To p
ID
1.5 A
2.1 A
3.3 A
VDD = 50 V
91044_12c
QGS QGD
QG
VG
Charge
10 V
D.U.T.
3 mA
VGS
VDS
IGID
0.3 µF
0.2 µF
50 kΩ
12 V
Current regulator
Current sampling resistors
Same type as D.U.T.
+
-
Document Number: 91044 www.vishay.com
S11-1048-Rev. C, 30-May-11 7
This document is subject to change without notice.
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
IRF720S, SiHF720S
Vishay Siliconix
Fig. 14 - For N-Channel
Vishay Siliconix maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for Silicon
Technology and Package Reliability represent a composite of all qualified locations. For related documents such as package/tape drawings, part marking, and
reliability data, see www.vishay.com/ppg?91044.
P.W. Period
dI/dt
Diode recovery
dV/dt
Ripple 5 %
Body diode forward drop
Re-applied
voltage
Reverse
recovery
current
Body diode forward
current
VGS = 10 Va
ISD
Driver gate drive
D.U.T. lSD waveform
D.U.T. VDS waveform
Inductor current
D = P.W.
Period
+
-
+
+
+
-
-
-
Peak Diode Recovery dV/dt Test Circuit
VDD
dV/dt controlled by Rg
Driver same type as D.U.T.
ISD controlled by duty factor “D”
D.U.T. - device under test
D.U.T. Circuit layout considerations
Low stray inductance
Ground plane
Low leakage inductance
current transformer
Rg
Note
a. VGS = 5 V for logic level devices
VDD
Document Number: 91364 www.vishay.com
Revision: 15-Sep-08 1
Package Information
Vishay Siliconix
TO-263AB (HIGH VOLTAGE)
Notes
1. Dimensioning and tolerancing per ASME Y14.5M-1994.
2. Dimensions are shown in millimeters (inches).
3. Dimension D and E do not include mold flash. Mold flash shall not exceed 0.127 mm (0.005") per side. These dimensions are measured at the
outmost extremes of the plastic body at datum A.
4. Thermal PAD contour optional within dimension E, L1, D1 and E1.
5. Dimension b1 and c1 apply to base metal only.
6. Datum A and B to be determined at datum plane H.
7. Outline conforms to JEDEC outline to TO-263AB.
5
4
13
L1
L2
D
BB
E
H
B
A
Detail A
A
A
c
c2
A
2 x e
2 x b2
2 x b
0.010 A B
MM ± 0.004 B
M
Base
metal
Plating b1, b3
(b, b2)
c1
(c)
Section B - B and C - C
Scale: none
Lead tip
4
34
(Datum A)
2CC
BB
5
5
View A - A
E1
D1
E
4
4
B
H
Seating plane
Gauge
plane
0° to 8°
Detail “A”
Rotated 90° CW
scale 8:1
L3 A1
L4
L
MILLIMETERS INCHES MILLIMETERS INCHES
DIM. MIN. MAX. MIN. MAX. DIM. MIN. MAX. MIN. MAX.
A 4.06 4.83 0.160 0.190 D1 6.86 - 0.270 -
A1 0.00 0.25 0.000 0.010 E 9.65 10.67 0.380 0.420
b 0.51 0.99 0.020 0.039 E1 6.22 - 0.245 -
b1 0.51 0.89 0.020 0.035 e 2.54 BSC 0.100 BSC
b2 1.14 1.78 0.045 0.070 H 14.61 15.88 0.575 0.625
b3 1.14 1.73 0.045 0.068 L 1.78 2.79 0.070 0.110
c 0.38 0.74 0.015 0.029 L1 - 1.65 - 0.066
c1 0.38 0.58 0.015 0.023 L2 - 1.78 - 0.070
c2 1.14 1.65 0.045 0.065 L3 0.25 BSC 0.010 BSC
D 8.38 9.65 0.330 0.380 L4 4.78 5.28 0.188 0.208
ECN: S-82110-Rev. A, 15-Sep-08
DWG: 5970
AN826
Vishay Siliconix
Document Number: 73397
11-Apr-05
www.vishay.com
1
RECOMMENDED MINIMUM PADS FOR D2PAK: 3-Lead
0.635
(16.129)
Recommended Minimum Pads
Dimensions in Inches/(mm)
0.420
(10.668)
0.355
(9.017)
0.145
(3.683)
0.135
(3.429)
0.200
(5.080)
0.050
(1.257)
Return to Index
Legal Disclaimer Notice
www.vishay.com Vishay
Revision: 12-Mar-12 1Document Number: 91000
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree
to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and
damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay
or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to
obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.