UTC MCR100 SCR SENSITIVE GATE SILICON CONTROLLED RECTIFIERS REVERSE BLOCKING THYRISTORS 1 DESCRIPTION PNPN devices designed for high volume, line-powered consumer applications such as relay and lamp drivers, small motor controls, gate drivers for larger thyristors, and sensing and detection circuits. Supplied in an inexpensive plastic TO-92 package which is readily adaptable for use in automatic insertion equipment. SOT-89 DESCRIPTION *Sensitive Gate Allows Triggering by Micro controllers and Other Logic circuits *Blocking Voltage to 600V *On-State Current Rating of 0.8A RMS at 80C *High Surge Current Capability - 10A *Minimum and Maximum Values of IGT, VGT and IH Specified for Ease of Design *Immunity to dV/dt - 20V/sec Minimum at 110C *Glass-Passivated Surface for Reliability and Uniformity 1: CATHODE 2: ANODE 3: GATE THERMAL CHARACTERISTICS SYMBOL MAX UNIT Thermal Resistance, Junction to Case PARAMETER RJC 75 C/W Thermal Resistance, Junction to Ambient RJA 200 C/W TL 260 C SYMBOL MAX UNIT VDRM,VRRM 200 400 600 V Lead Solder Temperature (<1/16" from case, 10 secs max) ABSOLUTE MAXIMUM RATINGS PARAMETER Peak Repetitive Off-State Voltage(note) (TJ=-40 to 110C, Sine Wave, 50 to 60Hz; Gate Open) MCR100-4 MCR100-6 MCR100-8 On-Sate RMS Current (Tc=80C) 180 Condition Angles Peak Non-Repetitive Surge Current (1/2 cycle, Sine Wave, 60Hz, TJ=25C) Circuit Fusing Considerations (t=8.3 ms) UTC IT(RMS) ITSM 2 It 0.8 A 10 0.415 A A2s UNISONIC TECHNOLOGIES CO., LTD. 1 QW-R301-002,B UTC MCR100 SCR PARAMETER SYMBOL MAX UNIT PGM 0.1 W PG(AV) 0.1 W Peak Gate Current - Forward (TA=25C, Pulse Width1.0s) IGM 1 A Peak Gate Voltage - Reverse (TA=25C, Pulse Width1.0s) VGRM 5 V TJ -40 to +110 C Forward Peak Gate Power (TA=25C, Pulse Width 1.0s) Forward Average Gate Power (TA=25C, t=8.3ms) Operating Junction Temperature Range @ Rated VRRM and VDRM Storage Temperature Range Tstg -40 to +150 C Note: VDRM and VRRM for all types can be applied on a continuous basis. Ratings apply for zero or negative gate voltage; however, positive gate voltage shall not be applied concurrent with negative potential on the anode. Blocking voltages shall not be tested with a constant current source such that the voltage ratings of the devices are exceeded. ELECTRICAL CHARACTERISTICS (Tj=25C, unless otherwise stated) PARAMETER TEST CONDITION SYMBOL MIN TYP MAX UNIT OFF CHARACTERISTICS Peak Forward or Reverse Blocking Current Tc=25C Tc=125C VD=Rated VDRM and VRRM; RGK=1k IDRM, IRRM 10 100 A ON CHARACTERISTICS Peak Forward On-State Voltage (Note1) ITM=1A Peak @ TA=25C Gate Trigger Current (Continuous dc)(note2) VAK=7Vdc, RL=100, TC=25C Holding Current (note 3) Tc=25 C VAK=7Vdc, initiating current=20mA Tc=-40 C Tc=25 C Tc=-40 C Latch Current Gate Trigger Current (continuous dc) (Note 2) VAK=7V, Ig=200A 1.7 VTM IGT IH IL V 40 200 0.5 5 10 mA 0.6 10 15 mA 0.62 0.8 1.2 A VAK=7Vdc, RL=100 Tc=25 C Tc=-40 C VGT V DYNAMIC CHARACTERISTICS Critical Rate of Rise of Off-State Voltage VD=Rated VDRM, Exponential Waveform, RGK=1000, TJ=110C Critical Rate of Rise of On-State IPK=20A; Pw=10sec; Current diG/dt=1A/sec, Igt=20mA Notes: 1. Indicates Pulse Test Width1.0ms, duty cycle 1% 2. RGK=1000 included in measurement. 3. Does not include RGK in measurement. UTC dV/dt di/dt 20 35 V/s 50 UNISONIC TECHNOLOGIES CO., LTD. A/s 2 QW-R301-002,B UTC MCR100 SCR VOLTAGE CURRENT CHARACTERISTIC OF SCR SYMBOL VDRM IDRM VRRM IRRM VTM IH PARAMETER Peak Repetitive Off Stat Forward Voltage Peak Forward Blocking Current Peak Repetitive Off State Reverse Voltage Peak Reverse Blocking Current Peak On State Voltage Holding Current CLASSIFICATION OF IGT RANK RANGE UTC B 48~105A C 95~200A AA 8~16A AB 14~21A AC 19~25A AD 23~52A UNISONIC TECHNOLOGIES CO., LTD. 3 QW-R301-002,B UTC MCR100 UTC SCR UNISONIC TECHNOLOGIES CO., LTD. 4 QW-R301-002,B UTC MCR100 SCR UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. UTC UNISONIC TECHNOLOGIES CO., LTD. 5 QW-R301-002,B