Thyristors 10 Amp Sensitive & Standard SCRs Sxx10xSx & Sxx10x Series RoHS Description This Sxx10x SCR series is ideal for uni-directional switch applications such as phase control, heating, motor speed controls, converters/rectifiers and capacitive discharge ignitions. These SCRs have a low gate current trigger level of 0.2 to 15 mA at approximately 1.5V, with a sensitive version of this series having a gate trigger current less than 500A. The sensitive gate SCR version is easily triggered by sense coils, proximity switches, and microprocessors. Features & Benefits Main Features Symbol Value Unit 10 A 400 to 1000 V 0.2 to 15 mA IT(RMS) VDRM /VRRM IGT Resources * Voltage capability up to 1000 V * Glass - passivated junctions * Surge capability up to 100 A at 60 Hz half cycle Applications Typical applications includes capacitive discharge system for motorcycle engine CDI, portable generator engine ignition, strobe lights and nailers, as well as generic rectifiers, battery voltage regulators and converters. Also AC control & rectification for power tools, home/brown goods, white goods appliances and 2-wheeler rectifier/ battery regulators. Additional Information Datasheet * Halogen free and RoHS compliant Samples Internally constructed isolated packages are offered for ease of heat sinking with highest isolation voltage. Schematic Symbol A K G (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 01/16/18 Thyristors 10 Amp Sensitive & Standard SCRs Absolute Maximum Ratings -- Sensitive SCRs Symbol Parameter IT(RMS) RMS on-state current Average on-state current IT(AV) Test Conditions Sxx10LSy TC = 80C Sxx10RSy /Sxx10NSy Sxx10DSy Sxx10VSy TC = 95C Sxx10LSy TC = 80C Sxx10RSy /Sxx10NSy Sxx10DSy Sxx10VSy TC = 95C Value Unit 10 A 6.4 A single half cycle; f = 50Hz; TJ (initial) = 25C 83 single half cycle; f = 60Hz; TJ (initial) = 25C 100 ITSM Peak non-repetitive surge current I2t I2t Value for fusing tp = 8.3 ms 41 A2s Critical rate of rise of on-state current f = 60 Hz ; TJ = 110C 100 A/s Peak gate current TJ = 110C 1 A Average gate power dissipation TJ = 110C 0.1 W Storage temperature range -40 to 150 C Operating junction temperature range -40 to 110 C Value Unit 10 A 6.4 A di/dt IGM PG(AV) Tstg TJ A Note: xx = voltage, y = sensitivity Absolute Maximum Ratings -- Standard SCRs Symbol IT(RMS) Parameter RMS on-state current Test Conditions Sxx10L TC = 95C Sxx10R / Sxx10N Sxx10D Sxx10V TC = 105C Sxx10L TC = 95C Sxx10R / Sxx10N Sxx10D TC = 105C Sxx10V single half cycle; f = 50Hz; TJ (initial) = 25C single half cycle; f = 60Hz; TJ (initial) = 25C IT(AV) Average on-state current ITSM Peak non-repetitive surge current I2t I2t Value for fusing tp = 8.3 ms 41 A2s Critical rate-of-rise of on-state current f = 60 Hz TJ = 125C 100 A/s Peak gate current TJ = 125C 2 A Average gate power dissipation TJ = 125C 0.5 W Storage temperature range -40 to 150 C Operating junction temperature range -40 to 125 C di/dt IGM PG(AV) Tstg TJ Note: xx = voltage (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 01/16/18 83 A 100 Thyristors 10 Amp Sensitive & Standard SCRs Electrical Characteristics (TJ = 25C, unless otherwise specified) - Sensitive SCRs Symbol IGT Value Test Conditions Sxx10xS2 Sxx10xS3 Unit VD = 6V RL = 100 MAX. VD = 6V RL = 100 MAX. 0.8 V VD = VDRM; RGK = 1k ; TJ = 110C TYP. 8 V/s VGD VD = VDRM; RL = 3.3 k; TJ = 110C MIN. 0.2 V VGRM IGR = 10A MIN. IH IT = 20mA (initial) MAX. 6 8 mA tq (1) MAX. 50 45 s tgt IG = 2 x IGT; PW = 15s; IT = 12A TYP. 4 5 s VGT dv/dt 200 500 6 A V NOTE: xx = voltage, x = package (1) IT=2A; tp=50s; dv/dt=5V/s; di/dt=-30A/s Electrical Characteristics (TJ = 25C, unless otherwise specified) - Standard SCRs Symbol IGT VGT Value Test Conditions Sxx10x VD = 12V RL = 60 MAX. 15 mA VD = 12V RL = 60 MAX. 1.5 V VD = VDRM; gate open; TJ = 100C 400V 350 600V 300 800V dv/dt 1000V 250 MIN. 400V VD = VDRM; gate open; TJ = 125C VGD Unit 100 V/s 250 600V 225 800V 200 VD = VDRM; RL = 3.3 k; TJ = 125C MIN. 0.2 V MAX. 30 mA tq IT = 200mA (initial) (1) MAX. 35 s tgt IG = 2 x IGT; PW = 15s; IT = 20A TYP. 2 s IH NOTE: xx = voltage, x = package (1) IT=2A; tp=50s; dv/dt=5V/s; di/dt=-30A/s Static Characteristics Symbol Test Conditions IT = 20A; tp = 380 s VTM Sxx10xyy IDRM / IRRM Sxx10x Unit 1.6 V TJ = 25C 400 - 600V 5 TJ = 110C 400 - 600V 250 400 - 800V 10 TJ = 25C VDRM / VRRM MAX. Value TJ = 100C TJ = 125C 1000V MAX. 20 400 - 800V 200 1000V 3000 400 - 800V 500 A Note: xx = voltage, x = package, yy = sensitivity (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 01/16/18 Thyristors 10 Amp Sensitive & Standard SCRs Thermal Resistances Symbol Parameter Value Junction to case (AC) R(J-C) Junction to ambient R(J-A) Sxx10RSy / Sxx10NSy 1.6 Sxx10LSy 3.0 Sxx10VSy 1.7 Sxx10DSy 1.45 Sxx10R / Sxx10N 1.6 Sxx10L 3.0 Sxx10V 1.7 Sxx10D 1.45 Sxx10RSy 40 Sxx10LSy 65 Sxx10VSy 85 Sxx10R 40 Sxx10L 50 Sxx10V 70 Unit C/W C/W Note: xx = voltage, y = sensitivity Figure 1: Normalized DC Gate Trigger Current vs. Junction Temperature (Sensitive SCR) Figure 2: N ormalized DC Gate Trigger Current vs. Junction Temperature (Standard SCR) 4.0 Ratio of IGT / IGT (TJ = 25C) Ratio of IGT / IGT (TJ = 25C) 4.0 3.0 2.0 1.0 0.0 -40 -15 10 35 60 Junction Temperature (TJ) -- (C) (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 01/16/18 85 110 3.0 2.0 1.0 0.0 -40 -15 10 35 60 Junction Temperature (TJ) -- (C) 85 110 125 Thyristors 10 Amp Sensitive & Standard SCRs Figure 3: Normalized DC Gate Trigger Voltage vs. Junction Temperature Figure 4: N ormalized DC Holding Current vs. Junction Temperature 2.0 Ratio of IH / IH (TJ = 25C) Ratio of VGT / VGT (TJ = 25C) 2.0 1.5 1.0 0.5 0.0 1.5 1.0 0.5 0.0 -40 -15 10 35 60 85 110 125 -40 -15 10 Junction Temperature (TJ) -- (C) Figure 5: On-State Current vs. On-State Voltage (Typical) 85 110 125 9 10 10 Average On-State Power Dissipation [PD(AV)] -- (Watts) TJ = 25C Instantaneous On-state Current (iT) - Amps 60 Figure 6: P ower Dissipation (Typical) vs. RMS On-State Current 32 28 24 20 16 12 8 4 0 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 9 8 7 6 5 4 3 2 1 0 1.6 0 1 2 Instantaneous On-state Voltage (vT) - Volts 130 125 125 Maximum Allowable Case Temperature (TC) - C 110 105 Sxx10RSy/ Sxx10RSy Sxx10NSy 100 Sxx10DSy Sxx10VSy 95 90 Sxx10LSy 85 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180 FREE AIR RATING 80 75 5 6 7 8 Sxx10R/ Sxx10R Sxx10N 120 Sxx10R Sxx10D Sxx10V Sxx10L 115 4 Figure 8: M aximum Allowable Case Temperature vs. Average On-State Current 130 120 3 RMS On-State Current [IT(RMS)] -- (Amps) Figure 7: Maximum Allowable Case Temperature vs. RMS On-State Current Maximum Allowable Case Temperature (TC) - C 35 Junction Temperature (TJ) -- (C) 115 Sxx10D Sxx10V 5 6 110 105 100 Sxx10RSy/ Sxx10RSy Sxx10NSy Sxx10DSy Sxx10VSy 95 90 Sxx10LSy 85 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180 FREE AIR RATING 80 75 70 Sxx10L 70 0 1 2 3 4 5 6 7 8 RMS On-State Current [IT(RMS)] - Amps 9 10 11 0 1 2 3 4 7 Average On-State Current [IT(AVE)] - Amps (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 01/16/18 Thyristors 10 Amp Sensitive & Standard SCRs Figure 9: Maximum Allowable Ambient Temperature vs. RMS On-State Current Figure 10: Maximum Allowable Ambient Temperature vs. Average On-State Current 120 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180 FREE AIR RATING Sxx10R 100 Maximum Allowable Ambient Temperature (TA) - C Maximum Allowable Case Temperature (TC) - C 120 Sxx10L 80 Sxx10V Sxx10RSy Sxx10LSy 60 40 Sxx10VSy 20 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180 FREE AIR RATING Sxx10R 100 Sxx10L 80 Sxx10RSy Sxx10LSy 60 Sxx10V 40 Sxx10VSy 20 0 0 0.0 0.5 1.0 1.5 2.0 0.0 2.5 0.5 Average On-State Current [IT(RMS)] - Amps 1.0 1.5 Average On-State Current [IT(AVE)] - Amps Note: xx = voltage, y = sensitivity Figure 11: Peak Capacitor Discharge Current Figure 12: P eak Capacitor Discharge Current Derating 1.2 1.0 Normalized Peak Current Peak Discharge Current (ITM) - Amps 1000 100 ITRM 0.8 0.6 0.4 Sensitive SCR Standard SCR 0.2 tW 10 0.5 0.0 10.0 1.0 50.0 Pulse Current Duration (tW) - ms Figure 13-1: Typical DC Holding Current with RGK vs. Junction Temperature for S60010xS2 (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 01/16/18 0 25 50 75 100 125 150 Case Temperature (TC) - C Figure 13-1: Typical DC Holding Current with RGK vs. Junction Temperature for S60010xS3 Thyristors 10 Amp Sensitive & Standard SCRs Figure 14-1: Typical DC Holding Current with RGK vs. Junction Temperature for S60010xS2 Figure 14-2: Typical DC Holding Current with RGK vs. Junction Temperature for S60010xS3 Figure 15-1: Typical Static dv/dt with RGK vs. Junction Temperature for S60010xS2 Figure 15-2: Typical Static dv/dt with RGK vs. Junction Temperature for S60010xS3 Figure 16-1: Typical turn off time with RGK vs. Junction Temperature for S60010xS2 Figure 16-2: Typical DC Gate Trigger Current with RGK vs. Junction Temperature for S60010xS3 (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 01/16/18 Thyristors 10 Amp Sensitive & Standard SCRs Figure 17: S urge Peak On-State Current vs. Number of Cycles Peak Surge (Non-repetitive) On-state Current (ITSM) - Amps 1000 SUPPLY FREQUENCY: 60 Hz Sinusoidal LOAD: Resistive RMS On-State Current: [IT(RMS)]: Maximum Rated Value at Specified Case Temperature Notes: 1. G ate control may be lost during and immediately following surge current interval. 2. O verload may not be repeated until junction temperature has returned to steady-state rated value. 100 10 1 1 10 100 1000 Surge Current Duration -- Full Cycles Soldering Parameters Pre Heat Pb - Free assembly - Temperature Min (Ts(min)) 150C - Temperature Max (Ts(max)) 200C - Time (min to max) (ts) 60 - 180 secs Average ramp up rate (Liquidus Temp) (TL) to peak 5C/second max TS(max) to TL - Ramp-up Rate 5C/second max Reflow - Temperature (TL) (Liquidus) 217C - Temperature (tL) 60 - 150 seconds 260 C Time within 5C of actual peak Temperature (tp) 20 - 40 seconds Ramp-down Rate 5C/second max Time 25C to peak Temperature (TP) 8 minutes Max. Do not exceed 280C (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 01/16/18 Ramp-up TL tL TS(max) Preheat TS(min) 25 Peak Temperature (TP) +0/-5 tP TP Temperature Reflow Condition Ramp-do Ramp-down tS time to peak temperature Time Thyristors 10 Amp Sensitive & Standard SCRs Physical Specifications Terminal Finish 100% Matte Tin-plated Body Material UL recognized epoxy meeting flammability rating 94V-0 Lead Material Copper Alloy Environmental Specifications Test AC Blocking Temperature Cycling Temperature/ Humidity Specifications and Conditions MIL-STD-750, M-1040, Cond A Applied Peak AC voltage @ 125C for 1008 hours MIL-STD-750, M-1051, 100 cycles; -40C to +150C; 15-min dwell-time EIA / JEDEC, JESD22-A101 1008 hours; 320V - DC: 85C; 85% rel humidity MIL-STD-750, M-1031, 1008 hours; 150C Design Considerations High Temp Storage Careful selection of the correct component for the application's operating parameters and environment will go a long way toward extending the operating life of the Thyristor. Good design practice should limit the maximum continuous current through the main terminals to 75% of the component rating. Other ways to ensure long life for a power discrete semiconductor are proper heat sinking and selection of voltage ratings for worst case conditions. Overheating, overvoltage (including dv/dt), and surge currents are the main killers of semiconductors. Correct mounting, soldering, and forming of the leads also help protect against component damage. Low-Temp Storage 1008 hours; -40C Resistance to Solder Heat MIL-STD-750 Method 2031 Solderability ANSI/J-STD-002, category 3, Test A Lead Bend MIL-STD-750, M-2036 Cond E (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 01/16/18 Thyristors 10 Amp Sensitive & Standard SCRs Product Selector Voltage Part Number 400V 600V 800V 1000V Gate Sensitivity Type Package Sxx10RS2 X X 0.2mA Sensitive SCR TO-220R Sxx10LS2 X X 0.2mA Sensitive SCR TO-220L Sxx10VS2 X X 0.2mA Sensitive SCR TO-251 Sxx10DS2 X X 0.2mA Sensitive SCR TO-252 Sxx10RS3 X X 0.5mA Sensitive SCR TO-220R Sxx10LS3 X X 0.5mA Sensitive SCR TO-220L Sxx10VS3 X X 0.5mA Sensitive SCR TO-251 Sxx10DS3 X X 0.5mA Sensitive SCR TO-252 Sxx10R X X X X 15mA Standard SCR TO-220R Sxx10L X X X X 15mA Standard SCR TO-220L Sxx10V X X X X 15mA Standard SCR TO-251 Sxx10D X X X X 15mA Standard SCR TO-252 Sxx10NS2 X X 15mA Sensitive SCR TO-263 Sxx10NS3 X X 15mA Sensitive SCR TO-263 Sxx10N X X 15mA Standard SCR TO-263 X X Note: xx = Voltage/10 Dimensions -- TO-251AA (V/I-Package) -- V/I-PAK Through Hole TC MEASURING POINT Anode E H D AREA: 0.040 IN2 Dimension 5.28 .208 J A A 5.34 .210 B R P Q S K C Cathode Anode GATE F G I (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 01/16/18 L Inches Millimeters Min Typ Max Min Typ Max 0.037 0.040 0.043 0.94 1.01 1.09 B 0.235 0.242 0.245 5.97 6.15 6.22 C 0.350 0.361 0.375 8.89 9.18 9.53 D 0.205 0.208 0.213 5.21 5.29 5.41 E 0.255 0.262 0.265 6.48 6.66 6.73 F 0.027 0.031 0.033 0.69 0.80 0.84 G 0.087 0.090 0.093 2.21 2.28 2.36 H 0.085 0.092 0.095 2.16 2.34 2.41 I 0.176 0.180 0.184 4.47 4.57 4.67 J 0.018 0.020 0.023 0.46 0.51 0.58 K 0.035 0.037 0.039 0.90 0.95 1.00 L 0.018 0.020 0.023 0.46 0.52 0.58 P 0.042 0.047 0.052 1.06 1.20 1.32 Q 0.034 0.039 0.044 0.86 1.00 1.11 R 0.034 0.039 0.044 0.86 1.00 1.11 S 0.074 0.079 0.084 1.86 2.00 2.11 Thyristors 10 Amp Sensitive & Standard SCRs Dimensions -- TO-252AA (D-Package) -- D-PAK Surface Mount Anode E D 6.71 .264 5.28 .208 TC MEASURING POINT Dimension A 6.71 .264 5.34 .210 B 1.60 .063 P Q C 1.80 .071 GATE F Cathode Anode AREA : 0.040 IN2 3 .118 G 4.60 .181 I O L K J H M N Inches Min Typ Millimeters Max Min Typ Max A 0.037 0.040 0.043 0.94 1.01 1.09 B 0.235 0.243 0.245 5.97 6.16 6.22 C 0.106 0.108 0.113 2.69 2.74 2.87 D 0.205 0.208 0.213 5.21 5.29 5.41 E 0.255 0.262 0.265 6.48 6.65 6.73 F 0.027 0.031 0.033 0.69 0.80 0.84 G 0.087 0.090 0.093 2.21 2.28 2.36 H 0.085 0.092 0.095 2.16 2.33 2.41 I 0.176 0.179 0.184 4.47 4.55 4.67 J 0.018 0.020 0.023 0.46 0.51 0.58 K 0.035 0.037 0.039 0.90 0.95 1.00 L 0.018 0.020 0.023 0.46 0.51 0.58 M 0.000 0.000 0.004 0.00 0.00 0.10 N 0.021 0.026 0.027 0.53 0.67 0.69 O 0 0 5 0 0 5 P 0.042 0.047 0.052 1.06 1.20 1.32 Q 0.034 0.039 0.044 0.86 1.00 1.11 Dimensions -- TO-263 (N-Package) -- D2PAK Surface Mount Dimension Inches Millimeters Min Max Min Max A 0.360 0.370 9.14 9.40 B 0.380 0.420 9.65 10.67 C 0.178 0.188 4.52 4.78 D 0.025 0.035 0.64 0.89 E 0.045 0.060 1.14 1.52 F 0.060 0.075 1.52 1.91 G 0.095 0.105 2.41 2.67 H 0.092 0.102 2.34 2.59 J 0.018 0.024 0.46 0.61 K 0.090 0.110 2.29 2.79 S 0.590 0.625 14.99 15.88 V 0.035 0.045 0.89 1.14 U 0.002 0.010 0.05 0.25 W 0.040 0.070 1.02 1.78 (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 01/16/18 Thyristors 10 Amp Sensitive & Standard SCRs Dimensions -- TO-220AB (R-Package) -- Non-Isolated Mounting Tab Common with Center Lead TC MEASURING POINT AREA (REF.) 0.17 IN2 O A E Dimension 8.13 .320 P ANODE B C 13.36 .526 D 7.01 .276 NOTCH IN GATE LEAD TO ID. NON-ISOLATED TAB F R G L H CATHODE ANODE GATE K N Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm). M J Inches Millimeters Min Max Min Max A 0.380 0.420 9.65 10.67 B 0.105 0.115 2.67 2.92 C 0.230 0.250 5.84 6.35 D 0.590 0.620 14.99 15.75 E 0.142 0.147 3.61 3.73 F 0.110 0.130 2.79 3.30 G 0.540 0.575 13.72 14.61 H 0.025 0.035 0.64 0.89 J 0.195 0.205 4.95 5.21 K 0.095 0.105 2.41 2.67 L 0.060 0.075 1.52 1.91 M 0.085 0.095 2.16 2.41 N 0.018 0.024 0.46 0.61 O 0.178 0.188 4.52 4.78 P 0.045 0.060 1.14 1.52 R 0.038 0.048 0.97 1.22 Min Max Min Max Dimensions -- TO-220AB (L-Package) -- Isolated Mounting Tab TC MEASURING POINT O A E P AREA (REF.) 0.17 IN2 Dimension 8.13 .320 B C 13.36 .526 D 7.01 .276 F R G L H CATHODE ANODE GATE K J N M (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 01/16/18 Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm). Inches Millimeters A 0.380 0.420 9.65 10.67 B 0.105 0.115 2.67 2.92 C 0.230 0.250 5.84 6.35 D 0.590 0.620 14.99 15.75 E 0.142 0.147 3.61 3.73 F 0.110 0.130 2.79 3.30 G 0.540 0.575 13.72 14.61 H 0.025 0.035 0.64 0.89 J 0.195 0.205 4.95 5.21 K 0.095 0.105 2.41 2.67 L 0.060 0.075 1.52 1.91 M 0.085 0.095 2.16 2.41 N 0.018 0.024 0.46 0.61 O 0.178 0.188 4.52 4.78 P 0.045 0.060 1.14 1.52 R 0.038 0.048 0.97 1.22 Thyristors 10 Amp Sensitive & Standard SCRs Packing Options Part Number Sxx10L/RyyTP Marking Weight Packing Mode Base Quantity Sxx10L/Ryy 2.2 g Tube 500 (50 per tube) Sxx10DyyTP Sxx10Dyy 0.3 g Tube 750 (75 per tube) Sxx10DyyRP Sxx10Dyy 0.3 g Embossed Carrier 2500 Sxx10VyyTP Sxx10Vyy 0.4 g Tube 750 (75 per tube) Sxx10L/RTP Sxx10L/R 2.2 g Tube 500 (50 per tube) Sxx10DTP Sxx10D 0.3 g Tube 750 (75 per tube) Sxx10DRP Sxx10D 0.3 g Embossed Carrier 2500 Sxx10VTP Sxx10V 0.4 g Tube 750 (75 per tube) Sxx10NSyTP Sxx10NSy 1.6 g Tube 500 (50 per tube) Sxx10NSyRP Sxx10NSy 1.6 g Embossed Carrie 500 Sxx10NTP Sxx10N 1.6 g Tube 500 (50 per tube) Sxx10NRP Sxx10N 1.6 g Embossed Carrier 500 Note: xx = Voltage/10; yy = Sensitivity TO-252 Embossed Carrier Reel Pack (RP) Specifications Meets all EIA-481-2 Standards * Cover tape 0.315 (8.0) 0.512 (13.0) Arbor Hole Dia. 0.059 Dia (1.5) XXXXXX Cathode DC XX DC XX XXXXXX * DC 0.524 (13.3) XX 0.63 (16.0) XXXXXX Gate XXXXXX 0.157 (4.0) Anode 12.99 (330.0) Dimensions are in inches (and millimeters). 0.64 (16.3) Direction of Feed Part Numbering System Part Marking System S 60 10 L S2 56 DEVICE TYPE COMPONENT TYPE LEAD FORM DIMENSIONS xx : Lead Form Option S : SCR VOLTAGE RATING 40 : 400V 60 : 600V 80 : 800V K0 : 1000V CURRENT 10: 10A SENSITIVITY & TYPE Sensitive SCR: S2: 200A S3: 500A Standard SCR: (blank): 15mA PACKAGE TYPE L : TO-220 Isolated R : TO-220 Non-Isolated V : TO-251 (VPAK) D : TO-252 (DPAK) N: TO-263 (D2PAK) TO-263AA (N Package) TO-220 AB - (L and R Package) TO-251AA - (V Package) TO-252AA - (D Package) Sxx10DS3 Sxx10DS3 Sxx10R YM (R) YMLDD (R) YMLDD (R) Date Code Marking Y:Year Code M: Month Code L: Location Code DD: Calendar Code Date Code Marking Y:Year Code M: Month Code XXX: Lot Trace Code (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 01/16/18