© 2018 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 01/16/18
Thyristors
10 Amp Sensitive & Standard SCRs
Sxx10xSx & Sxx10x Series
Description
This Sxx10x SCR series is ideal for uni-directional switch
applications such as phase control, heating, motor speed
controls, converters/rectifiers and capacitive discharge
ignitions.
These SCRs have a low gate current trigger level of 0.2 to
15 mA at approximately 1.5V, with a sensitive version of
this series having a gate trigger current less than 500µA.
The sensitive gate SCR version is easily triggered by sense
coils, proximity switches, and microprocessors.
Features & Benefits
• Halogen free and RoHS
compliant
• Glass – passivated
junctions
• Voltage capability up
to 1000 V
• Surge capability up
to 100 A at 60 Hz
half cycle
Main Features
Symbol Value Unit
IT(RMS) 10 A
VDRM /VRRM 400 to 1000 V
IGT 0.2 to 15 mA
Schematic Symbol
Applications
Typical applications includes capacitive discharge system
for motorcycle engine CDI, portable generator engine
ignition, strobe lights and nailers, as well as generic
rectifiers, battery voltage regulators and converters. Also
AC control & rectification for power tools, home/brown
goods, white goods appliances and 2-wheeler rectifier/
battery regulators.
Internally constructed isolated packages are offered for
ease of heat sinking with highest isolation voltage.
AK
G
RoHS
Additional Information
Datasheet Samples
Resources
© 2018 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 01/16/18
Thyristors
10 Amp Sensitive & Standard SCRs
Absolute Maximum Ratings — Standard SCRs
Symbol Parameter Test Conditions Value Unit
IT(RMS) RMS on-state current
Sxx10L TC = 95°C
10 A
Sxx10R / Sxx10N
Sxx10D
Sxx10V
TC = 105°C
IT(AV) Average on-state current
Sxx10L TC = 95°C
6.4 A
Sxx10R / Sxx10N
Sxx10D
Sxx10V
TC = 105°C
ITSM Peak non-repetitive surge current
single half cycle; f = 50Hz;
TJ (initial) = 25°C 83
A
single half cycle; f = 60Hz;
TJ (initial) = 25°C 100
I2tI2t Value for fusing tp = 8.3 ms 41 A2s
di/dt Critical rate-of-rise of on-state current f = 60 Hz TJ = 125°C 100 A/μs
IGM Peak gate current TJ = 125°C 2 A
PG(AV) Average gate power dissipation TJ = 125°C 0.5 W
Tstg Storage temperature range -40 to 150 °C
TJOperating junction temperature range -40 to 125 °C
Note: xx = voltage
Absolute Maximum Ratings — Sensitive SCRs
Symbol Parameter Test Conditions Value Unit
IT(RMS) RMS on-state current
Sxx10LSy TC = 80°C
10 A
Sxx10RSy /Sxx10NSy
Sxx10DSy
Sxx10VSy
TC = 95°C
IT(AV) Average on-state current
Sxx10LSy TC = 80°C
6.4 A
Sxx10RSy /Sxx10NSy
Sxx10DSy
Sxx10VSy
TC = 95°C
ITSM Peak non-repetitive surge current
single half cycle; f = 50Hz;
TJ (initial) = 25°C 83
A
single half cycle; f = 60Hz;
TJ (initial) = 25°C 100
I2t I2t Value for fusing tp = 8.3 ms 41 A2s
di/dt Critical rate of rise of on-state current f = 60 Hz ; TJ = 110°C 100 A/μs
IGM Peak gate current TJ = 110°C 1 A
PG(AV) Average gate power dissipation TJ = 110°C 0.1 W
Tstg Storage temperature range -40 to 150 °C
TJOperating junction temperature range -40 to 110 °C
Note: xx = voltage, y = sensitivity
© 2018 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 01/16/18
Thyristors
10 Amp Sensitive & Standard SCRs
Electrical Characteristics (TJ = 25°C, unless otherwise specified) – Sensitive SCRs
Symbol Test Conditions Value Unit
Sxx10xS2 Sxx10xS3
IGT VD = 6V RL = 100 ΩMAX. 200 500 μA
VGT VD = 6V RL = 100 ΩMAX. 0.8 V
dv/dt VD = VDRM; RGK = 1kΩ ; TJ = 110°C TYP. 8 V/μs
VGD VD = VDRM; RL = 3.3 kΩ; TJ = 110°C MIN. 0.2 V
VGRM IGR = 10μA MIN. 6 V
IHIT = 20mA (initial) MAX. 6 8 mA
tq(1) MAX. 50 45 μs
tgt IG = 2 x IGT; PW = 15µs; IT = 12A TYP. 4 5 μs
NOTE: xx = voltage, x = package
(1) IT=2A; tp=50µs; dv/dt=5V/µs; di/dt=-30A/µs
Symbol Test Conditions Value Unit
Sxx10x
IGT VD = 12V RL = 60 ΩMAX. 15 mA
VGT VD = 12V RL = 60 ΩMAX. 1. 5 V
dv/dt
VD = VDRM; gate open; TJ = 100°C
400V
MIN.
350
V/μs
600V 300
800V 250
1000V 100
VD = VDRM; gate open; TJ = 125°C
400V 250
600V 225
800V 200
VGD VD = VDRM; RL = 3.3 kΩ; TJ = 125°C MIN. 0.2 V
IHIT = 200mA (initial) MAX. 30 mA
tq(1) MAX. 35 μs
tgt IG = 2 x IGT; PW = 15µs; IT = 20A TYP. 2 μs
NOTE: xx = voltage, x = package
(1) IT=2A; tp=50µs; dv/dt=5V/µs; di/dt=-30A/µs
Electrical Characteristics (TJ = 25°C, unless otherwise specified) – Standard SCRs
Static Characteristics
Symbol Test Conditions Value Unit
VTM IT = 20A; tp = 380 µs MAX. 1. 6 V
IDRM / IRRM VDRM / VRRM
Sxx10xyy
TJ = 25°C 400 - 600V
MAX.
5
μA
TJ = 110°C 400 - 600V 250
Sxx10x
TJ = 25°C
400 - 800V 10
1000V 20
TJ = 100°C
400 - 800V 200
1000V 3000
TJ = 125°C 400 - 800V 500
Note: xx = voltage, x = package, yy = sensitivity
© 2018 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 01/16/18
Thyristors
10 Amp Sensitive & Standard SCRs
Thermal Resistances
Symbol Parameter Value Unit
Rθ(J-C) Junction to case (AC)
Sxx10RSy / Sxx10NSy 1. 6
°C/W
Sxx10LSy 3.0
Sxx10VSy 1. 7
Sxx10DSy 1.45
Sxx10R / Sxx10N 1. 6
Sxx10L 3.0
Sxx10V 1. 7
Sxx10D 1.45
Rθ(J-A) Junction to ambient
Sxx10RSy 40
°C/W
Sxx10LSy 65
Sxx10VSy 85
Sxx10R 40
Sxx10L 50
Sxx10V 70
Note: xx = voltage, y = sensitivity
Figure 1: Normalized DC Gate Trigger Current
vs. Junction Temperature (Sensitive SCR)
Figure 2: Normalized DC Gate Trigger Current
vs. Junction Temperature (Standard SCR)
0.0
1.0
2.0
3.0
4.0
-40-15 10 35 60 85 110
Junction Temperature (TJ) -- (°C)
Ratio of I
GT
/ I
GT
(T
J
= 25°C)
125
0.0
1.0
2.0
3.0
4.0
-40 -1510356085110
Junction Temperature (TJ) -- (°C)
Ratio of I
GT
/ I
GT
(T
J
= 25°C)
© 2018 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 01/16/18
Thyristors
10 Amp Sensitive & Standard SCRs
125
0.0
0.5
1.0
1.5
2.0
-40-15 10 35 60 85 110
Junction Te mperature (TJ) -- (°C)
Ratio of IH / IH (TJ = 25°C)
125
0.0
0.5
1.0
1.5
2.0
-40 -1510356085110
Junction Temperature (TJ) -- (°C)
Ratio of V
GT
/ V
GT
(T
J
= 25°C)
0
4
8
12
16
20
24
28
32
0.7 0.8 0.9 1.01.1 1.21.3 1.41.5 1.6
Instantaneous On-stat
e Current
(iT) – Amps
Instantaneous On-state Voltage (vT) – Volts
TJ = 25ºC
0
1
2
3
4
5
6
7
8
9
10
012345678910
RMS On-State Current [I
T(RMS)
] -- (Amps)
Average On-State Power Dissipation
[P
D(AV)
] -- (Watts)
Figure 5: On-State Current vs. On-State
Voltage (Typical)
Figure 6: Power Dissipation (Typical) vs. RMS
On-State Current
Figure 3: Normalized DC Gate Trigger Voltage
vs. Junction Temperature
Figure 4: Normalized DC Holding Current
vs. Junction Temperature
Figure 7: Maximum Allowable Case Temperature
vs. RMS On-State Current
Figure 8: Maximum Allowable Case Temperature
vs. Average On-State Current
70
75
80
85
90
95
100
105
110
115
120
125
130
012345678910 11
RMS On-State Current [IT(RMS)] - Amps
Sxx10RSy
Sxx10DSy
Sxx10VSy
Sxx10L
Sxx10LSy
Sxx10R
Sxx10D
Sxx10V
CURRENT WAVEFORM: Sinusoidal
LOAD: Resistive or Inductive
CONDUCTION ANGLE: 180°
FREE AIR RATING
Maximum Allowable Case
Temperature (TC) - °C
70
75
80
85
90
95
100
105
110
115
120
125
130
012345
67
Sxx10LSy
Sxx10RSy
Sxx10DSy
Sxx10VSy
Sxx10R
Sxx10D
Sxx10V
CURRENT WAVEFORM: Sinusoidal
LOAD: Resistive or Inductive
CONDUCTION ANGLE: 180°
FREE AIR RATING
Maximum Allowable Case
Temperature (TC) - °C
Average On-State Current [IT(AVE)] - Amps
Sxx10L
Sxx10RSy/
Sxx10NSy
Sxx10R/
Sxx10N
Sxx10RSy/
Sxx10NSy
© 2018 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 01/16/18
Thyristors
10 Amp Sensitive & Standard SCRs
Figure 11: Peak Capacitor Discharge Current Figure 12: Peak Capacitor Discharge Current Derating
Figure 9: Maximum Allowable Ambient Temperature
vs. RMS On-State Current
Figure 10: Maximum Allowable Ambient Temperature
vs. Average On-State Current
Note: xx = voltage, y = sensitivity
0
20
40
60
80
100
120
0.0 0.5 1.
01
.5
Average On-State Current [IT(AVE)] - Amps
Maximum Allowable Ambient
Te mperature (T
A
) - °C
Sxx10RSy
Sxx10LSy
Sxx10VSy
Sxx10R
Sxx10L
Sxx10V
CURRENT WAVEFORM: Sinusoidal
LOAD: Resistive or Inductive
CONDUCTION ANGLE: 180°
FREE AIR RATING
0.0
0.2
0.4
0.6
0.8
1.0
1.2
0255075100 12
51
50
Normalized Peak Current
Sensitive SCR
Case Temperature (TC) - °C
Standard SCR
10
100
1000
0.5 1.
01
0.0 50.0
Pulse Current Duration (tW) - ms
Peak Discharge Current (ITM) - Amps
ITRM
tW
0
20
40
60
80
100
120
0.00.5 1.01.5 2.
02
.5
Average On-State Current [I
T(RMS)
] - Amps
CURRENT WAVEFORM: Sinusoidal
LOAD: Resistive or Inductive
CONDUCTION ANGLE: 180°
FREE AIR RATING
Sxx10R
Sxx10L
Sxx10V
Sxx10RSy
Sxx10LSy
Sxx10VSy
Maximum Allowable Case Temperature
(T
C
) - °C
Figure 13-1: Typical DC Holding Current with RGK
vs. Junction Temperature for S60010xS2
Figure 13-1: Typical DC Holding Current with RGK
vs. Junction Temperature for S60010xS3
© 2018 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 01/16/18
Thyristors
10 Amp Sensitive & Standard SCRs
Figure 15-1: Typical Static dv/dt with RGK vs. Junction
Temperature for S60010xS2
Figure 15-2: Typical Static dv/dt with RGK vs. Junction
Temperature for S60010xS3
Figure 14-1: Typical DC Holding Current with RGK
vs. Junction Temperature for S60010xS2
Figure 14-2: Typical DC Holding Current with RGK
vs. Junction Temperature for S60010xS3
Figure 16-1: Typical turn off time with RGK vs. Junction
Temperature for S60010xS2
Figure 16-2: Typical DC Gate Trigger Current with RGK
vs. Junction Temperature for S60010xS3
© 2018 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 01/16/18
Thyristors
10 Amp Sensitive & Standard SCRs
Soldering Parameters
Reflow Condition Pb – Free assembly
Pre Heat
- Temperature Min (Ts(min))150°C
- Temperature Max (Ts(max))200°C
- Time (min to max) (ts)60 – 180 secs
Average ramp up rate (Liquidus Temp)
(TL) to peak 5°C/second max
TS(max) to TL - Ramp-up Rate 5°C/second max
Reflow - Temperature (TL) (Liquidus) 217°C
- Temperature (tL)60 – 150 seconds
Peak Temperature (TP)260+0/-5 °C
Time within 5°C of actual peak
Temperature (tp)20 – 40 seconds
Ramp-down Rate 5°C/second max
Time 25°C to peak Temperature (TP)8 minutes Max.
Do not exceed 280°C
Time
Temperature
TP
TL
TS(max)
TS(min)
25
tP
tL
tS
time to peak temperature
Preheat
P
r
e
h
eat
Ramp-upRamp-up
Ramp-down
R
am
p
-
do
1
10
100
1000
110100 1000
Peak Surge (Non-repetitive)
On-state Current (ITSM) – Amps
Surge Current Duration -- Full Cycles
Figure 17: Surge Peak On-State Current vs. Number of Cycles
SUPPLY FREQUENCY: 60 Hz Sinusoidal
LOAD: Resistive
RMS On-State Current: [IT(RMS)]: Maximum Rated
Value at Specified Case Temperature
Notes:
1. Gate control may be lost during and immediately
following surge current interval.
2. Overload may not be repeated until junction
temperature has returned to steady-state
rated value.
© 2018 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 01/16/18
Thyristors
10 Amp Sensitive & Standard SCRs
Physical Specifications Environmental Specifications
Test Specifications and Conditions
AC Blocking MIL-STD-750, M-1040, Cond A Applied
Peak AC voltage @ 125°C for 1008 hours
Temperature Cycling
MIL-STD-750, M-1051,
100 cycles; -40°C to +150°C; 15-min
dwell-time
Temperature/
Humidity
EIA / JEDEC, JESD22-A101
1008 hours; 320V - DC: 85°C; 85%
rel humidity
High Temp Storage MIL-STD-750, M-1031,
1008 hours; 150°C
Low-Temp Storage 1008 hours; -40°C
Resistance to
Solder Heat MIL-STD-750 Method 2031
Solderability ANSI/J-STD-002, category 3, Test A
Lead Bend MIL-STD-750, M-2036 Cond E
Terminal Finish 100% Matte Tin-plated
Body Material UL recognized epoxy meeting flammability
rating 94V-0
Lead Material Copper Alloy
Design Considerations
Careful selection of the correct component for the
application’s operating parameters and environment will
go a long way toward extending the operating life of the
Thyristor. Good design practice should limit the maximum
continuous current through the main terminals to 75% of
the component rating. Other ways to ensure long life for
a power discrete semiconductor are proper heat sinking
and selection of voltage ratings for worst case conditions.
Overheating, overvoltage (including dv/dt), and surge
currents are the main killers of semiconductors. Correct
mounting, soldering, and forming of the leads also help
protect against component damage.
© 2018 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 01/16/18
Thyristors
10 Amp Sensitive & Standard SCRs
Product Selector
Part Number Voltage Gate Sensitivity Type Package
400V 600V 800V 1000V
Sxx10RS2 X X 0.2mA Sensitive SCR TO-220R
Sxx10LS2 X X 0.2mA Sensitive SCR TO-220L
Sxx10VS2 X X 0.2mA Sensitive SCR TO-251
Sxx10DS2 X X 0.2mA Sensitive SCR TO-252
Sxx10RS3 X X 0.5mA Sensitive SCR TO-220R
Sxx10LS3 X X 0.5mA Sensitive SCR TO-220L
Sxx10VS3 X X 0.5mA Sensitive SCR TO-251
Sxx10DS3 X X 0.5mA Sensitive SCR TO-252
Sxx10R X X X X 15mA Standard SCR TO-220R
Sxx10L X X X X 15mA Standard SCR TO-220L
Sxx10V X X X X 15mA Standard SCR TO-251
Sxx10D X X X X 15mA Standard SCR TO-252
Sxx10NS2 X X 15mA Sensitive SCR TO-263
Sxx10NS3 X X 15mA Sensitive SCR TO-263
Sxx10N X X X X 15mA Standard SCR TO-263
Note: xx = Voltage/10
Dimensions — TO-251AA (V/I-Package) — V/I-PAK Through Hole
Dimension Inches Millimeters
Min Typ Max Min Typ Max
A 0.037 0.040 0.043 0.94 1. 01 1.09
B 0.235 0.242 0.245 5.97 6.15 6.22
C 0.350 0.361 0.375 8.89 9.18 9.53
D 0.205 0.208 0.213 5.21 5.29 5.41
E 0.255 0.262 0.265 6.48 6.66 6.73
F 0.027 0.031 0.033 0.69 0.80 0.84
G 0.087 0.090 0.093 2.21 2.28 2.36
H 0.085 0.092 0.095 2.16 2.34 2.41
I 0.176 0.180 0.184 4.47 4.57 4.67
J 0.018 0.020 0.023 0.46 0.51 0.58
K 0.035 0.037 0.039 0.90 0.95 1. 0 0
L 0.018 0.020 0.023 0.46 0.52 0.58
P 0.042 0.047 0.052 1.06 1.20 1.32
Q 0.034 0.039 0.044 0.86 1. 0 0 1. 11
R 0.034 0.039 0.044 0.86 1. 0 0 1. 11
S 0.074 0.079 0.084 1.86 2.00 2.11
AREA: 0.040 IN
2
T
C
MEASURING POINT
GATE G
I
E
D
A
B
C
F
J
H
K
L
5.28
.208
5.34
.210
Anode
Cathode
Anode
P
Q
RS
© 2018 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 01/16/18
Thyristors
10 Amp Sensitive & Standard SCRs
Dimensions — TO-252AA (D-Package) — D-PAK Surface Mount
Dimensions — TO-263 (N-Package) — D2PAK Surface Mount
Dimension Inches Millimeters
Min Typ Max Min Ty p Max
A0.037 0.040 0.043 0.94 1. 01 1.09
B 0.235 0.243 0.245 5.97 6.16 6.22
C 0.106 0.108 0.113 2.69 2.74 2.87
D 0.205 0.208 0.213 5.21 5.29 5.41
E 0.255 0.262 0.265 6.48 6.65 6.73
F 0.027 0.031 0.033 0.69 0.80 0.84
G 0.087 0.090 0.093 2.21 2.28 2.36
H 0.085 0.092 0.095 2.16 2.33 2.41
I 0.176 0.179 0.184 4.47 4.55 4.67
J 0.018 0.020 0.023 0.46 0.51 0.58
K0.035 0.037 0.039 0.90 0.95 1. 0 0
L 0.018 0.020 0.023 0.46 0.51 0.58
M 0.000 0.000 0.004 0.00 0.00 0.10
N 0.021 0.026 0.027 0.53 0.67 0.69
O 0° 0° 5° 0° 0° 5°
P 0.042 0.047 0.052 1.06 1.20 1.32
Q 0.034 0.039 0.044 0.86 1. 0 0 1. 11
M
O
N
H
J
L
K
.118
3
.063
1.60
.071
1.80
.264
6.71
.264
6.71
.181
4.60
GATE
Anode
Cathode
Anode
T
C
MEASURING POINT
G
I
D
E
A
B
C
F
5.28
.208
5.34
.210
: 0.040 IN
2
AREA
P
Q
Dimension Inches Millimeters
Min Max Min Max
A 0.360 0.370 9.14 9.40
B 0.380 0.420 9.65 10.67
C 0.178 0.188 4.52 4.78
D 0.025 0.035 0.64 0.89
E 0.045 0.060 1. 14 1.52
F 0.060 0.075 1.52 1.91
G 0.095 0.105 2.41 2.67
H 0.092 0.102 2.34 2.59
J 0.018 0.024 0.46 0.61
K 0.090 0.110 2.29 2.79
S 0.590 0.625 14.99 15.88
V 0.035 0.045 0.89 1. 14
U 0.002 0.010 0.05 0.25
W 0.040 0.070 1.02 1.78
© 2018 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 01/16/18
Thyristors
10 Amp Sensitive & Standard SCRs
Dimensions — TO-220AB (R-Package) — Non-Isolated Mounting Tab Common with Center Lead
Dimension Inches Millimeters
Min Max Min Max
A 0.380 0.420 9.65 10.67
B 0.105 0.115 2.67 2.92
C 0.230 0.250 5.84 6.35
D 0.590 0.620 14.99 15.75
E 0.142 0.147 3.61 3.73
F 0.110 0.130 2.79 3.30
G 0.540 0.575 13.72 14.61
H 0.025 0.035 0.64 0.89
J 0.195 0.205 4.95 5.21
K 0.095 0.105 2.41 2.67
L 0.060 0.075 1.52 1.91
M 0.085 0.095 2.16 2.41
N 0.018 0.024 0.46 0.61
O 0.178 0.188 4.52 4.78
P 0.045 0.060 1. 14 1.52
R 0.038 0.048 0.97 1.22
K
J
A
H
G
B
F
E
C
D
L
R
T
C
MEASURING POINT
ANODE
O
P
N
M
.276
7. 01
.526
13.36
.320
8.13
AREA (REF.) 0.17 IN
2
NOTCH IN
GATE LEAD
TO ID.
NON-ISOLATED
TAB
GATECATHODE ANODE
Dimensions — TO-220AB (L-Package) — Isolated Mounting Tab
Dimension Inches Millimeters
Min Max Min Max
A 0.380 0.420 9.65 10.67
B 0.105 0.115 2.67 2.92
C 0.230 0.250 5.84 6.35
D 0.590 0.620 14.99 15.75
E 0.142 0.147 3.61 3.73
F 0.110 0.130 2.79 3.30
G 0.540 0.575 13.72 14.61
H 0.025 0.035 0.64 0.89
J 0.195 0.205 4.95 5.21
K 0.095 0.105 2.41 2.67
L 0.060 0.075 1.52 1.91
M 0.085 0.095 2.16 2.41
N 0.018 0.024 0.46 0.61
O 0.178 0.188 4.52 4.78
P 0.045 0.060 1. 14 1.52
R 0.038 0.048 0.97 1.22
A
H
G
B
F
E
C
D
L
R
T
C
MEASURING POINT AREA (REF.) 0.17 IN
2
O
P
N
M
.320
8.13
.526
13.36
.276
7. 01
K
J
GATECATHODE ANODE
Note: Maximum torque to
be applied to mounting tab
is 8 in-lbs. (0.904 Nm).
Note: Maximum torque to
be applied to mounting tab
is 8 in-lbs. (0.904 Nm).
© 2018 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 01/16/18
Thyristors
10 Amp Sensitive & Standard SCRs
Packing Options
Part Number Marking Weight Packing Mode Base Quantity
Sxx10L/RyyTP Sxx10L/Ryy 2.2 g Tube 500 (50 per tube)
Sxx10DyyTP Sxx10Dyy 0.3 g Tube 750 (75 per tube)
Sxx10DyyRP Sxx10Dyy 0.3 g Embossed Carrier 2500
Sxx10VyyTP Sxx10Vyy 0.4 g Tube 750 (75 per tube)
Sxx10L/RTP Sxx10L/R 2.2 g Tube 500 (50 per tube)
Sxx10DTP Sxx10D 0.3 g Tube 750 (75 per tube)
Sxx10DRP Sxx10D 0.3 g Embossed Carrier 2500
Sxx10VTP Sxx10V 0.4 g Tube 750 (75 per tube)
Sxx10NSyTP Sxx10NSy 1.6 g Tube 500 (50 per tube)
Sxx10NSyRP Sxx10NSy 1.6 g Embossed Carrie 500
Sxx10NTP Sxx10N 1.6 g Tube 500 (50 per tube)
Sxx10NRP Sxx10N 1.6 g Embossed Carrier 500
Note: xx = Voltage/10; yy = Sensitivity
0.512 (13.0) Arbor
Hole Dia.
DC
XXXXXX
XXXXXX
DC
XXXXXX
DC
XXXXXX
XX
XX
XX
Gate Cathode
Anode
0.63
(16.0)
0.157
(4.0)
0.64
(16.3)
12.99
(330.0)
0.524
(13.3)
0.315
(8.0)
0.059 Dia
(1.5)
*
*Cover tape
Direction of Feed
Dimensions
are in inches
(and millimeters).
TO-252 Embossed Carrier Reel Pack (RP) Specifications
Meets all EIA-481-2 Standards
Part Numbering System Part Marking System
CURRENT
10: 10A
SENSITIVITY & TYPE
Sensitive SCR:
S2: 200µA
Standard SCR:
(blank): 15mA
PACKAGE TYPE
L:TO-220 Isolated
R : TO-220 Non-Isolated
V:TO-251 (VPAK)
D:TO-252 (DPAK)
VOLTAGE RATING
40 :
400V
60 :
600V
80 :
800V
K0 :
1000V
LEAD FORM DIMENSIONS
xx
:
Lead Form Option
S 60 10 L S2 56
DEVICE TYPE
S :
SCR
S3: 500µA
®
M
Y
Sxx10R
TO-220 AB - (L and R Package)
YMLDD ®
Date Code Marking
Y:Year Code
M: Month Code
L: Location Code
DD: Calendar Code
YMLDD ®
TO-251AA - (V Package)
TO-252AA - (D Package)
Sxx10DS3Sxx10DS3
Date Code Marking
Y:Year Code
M: Month Code
XXX: Lot Trace Code
COMPONENT TYPE
N: TO-263 (D2PAK)
TO-263AA (N Package)
