July 2013
Common Mode Filters
For power line
ACM series
ACM4520 [1808 inch]*
ACM7060 [2824 inch]
ACM9070 [3628 inch]
ACM1211 [4844 inch]
ACM1513 [6052 inch]
* Dimensions Code JIS[EIA]
EMC Components
(2/15)
001-01 / 20130723 / e9713_acm.fm
EMC Components
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH
or less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (cars, electric trains, ships, etc.)
(3) Medical equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(7) Transportation control equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(13) Other applications that are not considered general-purpose
applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
REMINDERS
(3/15)
001-01 / 20130723 / e9713_acm.fm
• All specifications are subject to change without notice.
EMC Components
Common Mode Filters
For power line
FEATURES
Chip common mode filter for large current applications.
For each series, there is excellent common mode impedance and noise suppression in a compact case.
ACM4520
Low profile and small size makes it optimal for surface mounting.
ACM7060, 9070, 1211, 1513
Compatible with high-density portable devices, which are always being made smaller and lighter, because the height has been reduced.
APPLICATION
ACM4520
Power line noise countermeasure for electronic equipment (DVCs, DVD cams, DSCs, etc.).
ACM7060, 9070, 1211, 1513
Power line noise countermeasure for various electronic equipment.
Noise countermeasure for adapter lines and battery lines or larger electronic equipment such as note book PCs and word processors.
PART NUMBER CONSTRUCTION
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
The Storage temperature range is for after the circuit board is mounted.
Overview of the ACM Series
ACM 4520 - 901 - 2P - T - □□□
Series name L×W×H Dimensions Impedance Number of lines Packaging style Internal code
(mm) (:) at 100MHz
4520 4.5×2.0×2.0 901 900 2P 2 lines T ø180mm reel
7060 7.0×6.0×3.5 142 1400 TL ø330mm reel
9070 9.0×7.0×4.5
1211 12.0×11.0*6.0
1513 15.0×13.0×6.0
Type
Temperature range
Reel diameter Package quantity Individual weight
Operating
temperature
Storage
temperature
（°C） （°C） （mm） （pieces/reel） （g）
ACM4520 –40 to +85 –40 to +85 ø180 800 0.15
ø330 2,500
ACM7060 –40 to +85 –40 to +85 ø330 1,500 0.35
ACM9070 –40 to +85 –40 to +85 ø330 800 0.82
ACM1211 –40 to +85 –40 to +85 ø330 500 2.2
ACM1513 –40 to +85 –40 to +85 ø330 500 3.15
Product compatible with RoHS directive
Halogen-free
Compatible with lead-free solders
RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/
Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
(4/15)
001-01 / 20130723 / e9713_acm.fm
• All specifications are subject to change without notice.
EMC Components
Overview of the ACM Series
RECOMMENDED REFLOW PROFILE
Preheating Soldering Peak
Temp. Time Temp. Time Temp. Time
T1 T2 t1 T3 t2 T4 t3
150°C 180°C 60 to 120s 230°C 10 to 30s 245°C 5s
Natural
cooling
t3
t1
Preheating
t2
Soldering
T3 T3
T4
T2
T1
t: Time
Peak
T: Temperature
(5/15)
001-01 / 20130723 / e9713_acm.fm
• All specifications are subject to change without notice.
EMC Components
ACM series
ACM4520 Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM
4.5
4.7±0.2
4.5±0.22.0max.
0.750.75
2.0
0.650.65
1
2
4
3
Wire
Ferrite
Dimensions in mm
1.25 3.5 1.25
0.95 1.05 0.95
2.0
Dimensions in mm
1
2
4
3
• No polarity
(6/15)
001-01 / 20130723 / e9713_acm.fm
• All specifications are subject to change without notice.
EMC Components
ACM series ACM4520 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
△: Includes packaging style indication (T: ø180mm reel, TL: ø330mm reel).
○Measurement equipment
＊ Equivalent measurement equipment may be used.
IMPEDANCE VS. FREQUENCY CHARACTERISTICS
○Measurement equipment
＊ Equivalent measurement equipment may be used.
Common mode
impedance
(:) [at 100MHz]
DC resistance
(:)max.
[1 line]
Rated current
(A)max. Rated voltage
(V)max.
Insulation
resistance
(M:)min.
Part No.
min. typ. 60°C 85°C
180 230 0.05 3.0 2.6 50 10 ACM4520-231-2P-△-□□□
300 420 0.055 2.8 2.4 50 10 ACM4520-421-2P-△-□□□
650 900 0.06 2.3 2.0 50 10 ACM4520-901-2P-△-□□□
1000 1400 0.08 1.7 1.5 50 10 ACM4520-142-2P-△-□□□
Measurement item Product No. Manufacturer
Common mode impedance 4991A Agilent Technologies
DC resistance 4338A Agilent Technologies
Insulation resistance 4339A Agilent Technologies
Product No. Manufacturer
4991A Agilent Technologies
1 10 100 1000
10000
1000
1
10
100
Frequency (MHz)
Impedance (Ω)
901 Common mode
231 Common mode
421 Common mode
142 Common mode
231 Differential mode
901 Differential mode
421 Differential mode
142 Differential mode
(7/15)
001-01 / 20130723 / e9713_acm.fm
• All specifications are subject to change without notice.
EMC Components
ACM series
ACM7060 Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM
1.5±0.2
4.0typ.
1.5±0.2
1.5±0.2 1.5±0.2
1.5±0.2
3.5max.
7.0±0.2
6.0±0.2
1
2
4
3
Dimensions in mm
1.51.5 1.5
4.02.5 2.5
Dimensions in mm
1
2
4
3
• No polarity
(8/15)
001-01 / 20130723 / e9713_acm.fm
• All specifications are subject to change without notice.
EMC Components
ACM series ACM7060 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
○Measurement equipment
＊ Equivalent measurement equipment may be used.
IMPEDANCE VS. FREQUENCY CHARACTERISTICS
○Measurement equipment
＊ Equivalent measurement equipment may be used.
Common mode impedance
(:) [100MHz]
DC resistance
(m:)max.
[1 line]
Rated current
(A)max.
Insulation
resistance
(M:)min.
Rated voltage
(V)max. Part No.
min. typ.
225 300 10 5 10 80 ACM7060-301-2PL-TL01
500 700 15 410 80 ACM7060-701-2PL-TL01
Measurement item Product No. Manufacturer
Common mode impedance 4991A Agilent Technologies
DC resistance 4338A Agilent Technologies
Insulation resistance 4339A Agilent Technologies
Product No. Manufacturer
4991A Agilent Technologies
1 10 100 1000
10000
1000
1
10
100
Frequency (MHz)
Impedance (Ω)
301 Common mode
701 Common mode
301 Differential mode
701 Differential mode
(9/15)
001-01 / 20130723 / e9713_acm.fm
• All specifications are subject to change without notice.
EMC Components
ACM series
ACM9070 Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM
1.5±0.2 1.5±0.2
2.0±0.2
4.5max.
9.0±0.2
7.0±0.2
1
2
4
3
1.5±0.2
6.0typ.
1.5±0.2
Dimensions in mm
Dimensions in mm
1
2
4
3
• No polarity
(10/15)
001-01 / 20130723 / e9713_acm.fm
• All specifications are subject to change without notice.
EMC Components
ACM series ACM9070 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
○Measurement equipment
＊ Equivalent measurement equipment may be used.
IMPEDANCE VS. FREQUENCY CHARACTERISTICS
○Measurement equipment
＊ Equivalent measurement equipment may be used.
Common mode impedance
(:) [100MHz]
DC resistance
(m:)max.
[1 line]
Rated current
(A)max.
Insulation
resistance
(M:)min.
Rated voltage
(V)max. Part No.
min. typ.
500 700 10 5 10 80 ACM9070-701-2PL-TL01
Measurement item Product No. Manufacturer
Common mode impedance 4991A Agilent Technologies
DC resistance 4338A Agilent Technologies
Insulation resistance 4339A Agilent Technologies
Product No. Manufacturer
4991A Agilent Technologies
1 10 100 1000
10000
1000
1
10
100
Frequency (MHz)
Impedance (Ω)
701 Common mode 701 Differential mode
(11/15)
001-01 / 20130723 / e9713_acm.fm
• All specifications are subject to change without notice.
EMC Components
ACM series
ACM1211 Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM
12.0±0.3
11.0±0.3
1
2
4
3
2.3±0.2
7.4typ.
2.3±0.2
6.0max.
2.7±0.2 2.7±0.2
2.5±0.2
Dimensions in mm
2.52.7 2.7
7.63.2 3.2
Dimensions in mm
1
2
4
3
• No polarity
(12/15)
001-01 / 20130723 / e9713_acm.fm
• All specifications are subject to change without notice.
EMC Components
ACM series ACM1211 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
○Measurement equipment
＊ Equivalent measurement equipment may be used.
IMPEDANCE VS. FREQUENCY CHARACTERISTICS
○Measurement equipment
＊ Equivalent measurement equipment may be used.
Common mode impedance
(:) [100MHz]
DC resistance
(m:)max.
[1 line]
Rated current
(A)max.
Insulation
resistance
(M:)min.
Rated voltage
(V)max. Part No.
min. typ.
500 700 6 8 10 80 ACM1211-701-2PL-TL01
750 1000 14 610 80 ACM1211-102-2PL-TL01
Measurement item Product No. Manufacturer
Common mode impedance 4991A Agilent Technologies
DC resistance 4338A Agilent Technologies
Insulation resistance 4339A Agilent Technologies
Product No. Manufacturer
4991A Agilent Technologies
1 10 100 1000
10000
1000
1
10
100
Frequency (MHz)
Impedance (Ω)
701 Common mode
102 Common mode 701 Differential mode
102 Differential mode
(13/15)
001-01 / 20130723 / e9713_acm.fm
• All specifications are subject to change without notice.
EMC Components
ACM series
ACM1513 Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM
2.3±0.2
10.4typ.
2.3±0.2
15.0±0.5
3.8±0.2 2.7±0.22.7±0.2
13.0±0.4
1
2
4
3
6.0max.
Dimensions in mm
3.82.7 2.7
10.43.3 3.3
Dimensions in mm
1
2
4
3
• No polarity
(14/15)
001-01 / 20130723 / e9713_acm.fm
• All specifications are subject to change without notice.
EMC Components
ACM series ACM1513 Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
○Measurement equipment
＊ Equivalent measurement equipment may be used.
IMPEDANCE VS. FREQUENCY CHARACTERISTICS
○Measurement equipment
＊ Equivalent measurement equipment may be used.
Common mode impedance
(:) [100MHz]
DC resistance
(m:)max.
[1 line]
Rated current
(A)max.
Insulation
resistance
(M:)min.
Rated voltage
(V)max. Part No.
min. typ.
450 550 4 10 10 50 ACM1513-551-2PL-TLHF
Measurement item Product No. Manufacturer
Common mode impedance 4991A Agilent Technologies
DC resistance 4338A Agilent Technologies
Insulation resistance 4339A Agilent Technologies
Product No. Manufacturer
4991A Agilent Technologies
1 10 100 1000
10000
1000
10
100
Frequency (MHz)
Impedance (Ω)
701 Common mode
701 Differential mode
(15/15)
001-01 / 20130723 / e9713_acm.fm
• All specifications are subject to change without notice.
EMC Components
ACM series
Packaging style
REEL DIMENSIONS
TAPE DIMENSIONS
Ty p e A W1 W2 N E
ACM4520 ø330±2 13.5±0.5 17.5±1 100±1 2 typ.
ø180±3 13±0.3 17±1.4 60+1/–0 2 typ.
ACM7060 ø330±2 16.4+2/–0 20.4 typ. 100±1 2 typ.
ACM9070 ø330±2 16.4+2/–0 20.4 typ. 100±1 2 typ.
ACM1211 ø330±2 24.4+2/–0 28.4 typ. 100±1 2 typ.
ACM1513 ø330±2 24.4+2/–0 28.4 typ. 100±1 2 typ.
Dimensions in mm
Ty p e A B øD0 E F P0 P1 P2 W K t
ACM4520 4.75±0.1 5.05±0.1 1.55+0.1/0 1.75±0.1 5.5±0.05 4.0±0.1 8.0±0.1 2.0±0.05 12.0±0.2 2.05±0.05 0.3±0.1
ACM7060 6.6±0.1 7.6±0.1 1.5+0.1/0 1.75±0.1 7.5±0.1 4.0±0.1 8.0±0.1 2.0±0.1 16.0±0.3 3.6±0.1 0.4±0.05
ACM9070 7.6±0.1 9.6±0.1 1.5+0.1/0 1.75±0.1 7.5±0.1 4.0±0.1 12.0±0.1 2.0±0.1 16.0±0.3 4.6±0.1 0.4±0.05
ACM1211 11.5±0.1 12.5±0.1 1.5+0.1/0 1.75±0.1 11.5±0.1 4.0±0.1 16.0±0.1 2.0±0.1 24.0±0.3 6.4±0.1 0.5±0.05
ACM1513 13.4±0.1 15.5±0.1 1.5+0.1/0 1.75±0.1 11.5±0.1 4.0±0.1 16.0±0.1 2.0±0.1 24.0+0.3/–0.1 7.3±0.1 0.4±0.05
ø13.0±0.2
ø21.0±0.8
N
E2.0±0.5
A
Dimensions in mm
1.0
W2
W1
B
FE
W
P0P2
P1
A
øD0 t
K
160min. Taping 440min.
Drawing direction
500 to 560min.
Dimensions in mm