Automotive Relays PCB Single Relays Power Relay K (Sealed) n n n Limiting continuous current 45A Wide voltage range 24VDC coil versions available Typical applications ABS control, blower fans, car alarm, cooling fan, engine control, fuel pump, hazard warning signal, heated front screen, heated rear screen, ignition, lamps front/rear/fog light, interior lights, main switch/supply relay, seat control, seatbelt pretensioner, sun roof, turn signal, valves, window lifter, wiper control. F076_fcw2b Contact Data Typical applications Resistive/inductive Resistive/inductive Indicator lamps Headlights, Headlights loads loads capacitive loads capacitive loads Contact arrangement 1 form A, 1 NO 1 form C, 1 CO 1 form A, 1 NO 1 form A, 1 NO 1 form C, 1 CO Rated voltage 12VDC 12VDC 12VDC 12VDC 12VDC A/B (NO/NC)A/B (NO/NC) Rated current 45A 45/30A 30A 40A 40/25A Limiting continuous current 23C 45A 45/30A 30A 40A 40/25A 85C 30A 30/25A 25A 25A 25/20A 1) 3) Limiting making current 100A 100/30A 120A 180A 180/60A Limiting breaking current2) 60A 60/30A 60A 60A 60/30A Contact material AgNi0.15 AgNi0.15 AgSnO2 AgSnO2 AgSnO2 Min. recommended contact load 1A at 5VDC4) Initial voltage drop, at 10A, typ./max. 20/300mV Operate/release time typ. 5/3ms5) Electrical endurance >2x105 ops. >2x105 ops. >2.2x106 ops. >105 ops. >105 ops. at 13.5VDC, 40A at 13.5VDC, 40A up to 8x21W up to 4x60W up to 4x60W Mechanical endurance, DC coil >107 ops. 1) 2) 3) 4) 5) The values apply to a resistive or inductive load with suitable spark suppression and at maximum 13.5VDC for 12VDC or 27VDC for 24VDC load voltages. For a load current duration of maximum 3s for a make/break ratio of 1:10. Corresponds to a peak inrush current on initial actuation (cold filament). See chapter Diagnostics of Relays in our Application Notes or consult the internet at http://relays.te.com/appnotes/ For unsuppressed relay coil. A low resistive suppression device in parallel to the relay coil increases the release time and reduces the lifetime caused by increased erosion and/or higher risk of contact tack welding. Max. DC load breaking capacity Coil operating range TE0556-E TE0555-6 Does not tak the temperat the contact c E = pre-ener Load limit curve 1: arc extinguishes, during transit time (changeover contact). Load limit curve 2: safe shutdown, no stationary arc (make contact). Load limit curves measured with low inductive resistors verified for 1000 switching events. 06-2014, Rev. 0614 www.te.com (c) 2014 Tyco Electronics Corporation, a TE Connectivity Ltd. company. Catalog and product specification according to IEC 61810-1 and to be used only together with the `Definitions' section. Does not take into account the temperature rise due to the contact current E = pre-energization Catalog and product data is subject to the terms of the disclaimer and all chapters of the `Definitions' section, available at http://relays.te.com/definitions Catalog product data, `Definitions' section, application notes and all specifications are subject to change. 1 Automotive Relays PCB Single Relays Power Relay K (Sealed) (Continued) Coil Data Rated coil voltage Coil versions, DC coil Coil Rated Operate code voltage voltage VDC VDC 001 12 6.9 022 24 14.1 12VDC / 24VDC Release voltage VDC 1.2 2.4 Coil resistance 10% 90 362 Rated coil power W 1.6 1.6 All figures are given for coil without pre-energization, at ambient temperature +23C. Other coils on request. Insulation Data Initial dielectric strength between open contacts between contact and coil 500VACrms 500VACrms Other Data EU RoHS/ELV compliance compliant Ambient temperature, DC coil -40 to +85C6) Climatic cycling with condensation, EN ISO 6988 3 cycles, storage 8/16h Temperature cycling (shock), IEC 60068-2-14, Na 20 cycles, -40/+85C (dwell time 1h) Damp heat cyclic, IEC 60068-2-30, Db, Variant 1 6 cycles, upper air temperature 55C Terminal Assignment Bottom view on solder pins Other Data (continued) Damp heat constant, 56 days, upper air temperature 55C IEC 60068-2-3, method Ca RT III - immersion cleanable version Corrosive gas, IEC 60068-2-42 10 days IEC 60068-2-43 10 days Vibration resistance (functional), IEC 60068-2-6 (sine pulse form), acceleration, acc. to position 10 to 200Hz, 20 to 40g7) Shock resistance (functional), IEC 60068-2-27 (half sine form single pulses), acceleration, acc. to position 8ms 30g7) Terminal type PCB Weight sealed version approx. 22g (0.77oz) open version approx. 19g (0.67oz) Solderability (aging 3: 4h/155C) for leaded process (Tm = 183C), for Pb-free process (Tm = 217C), IEC 60068-2-20 Ta, method 1, hot dip 5s, 215C Storage conditions according IEC 600688 8) Packaging unit sealed version 525 pcs. 6) See coil operating range DC. 7) No change in the switching state >10s. 8) For general storage and processing recommendations please refer to our Application Notes and especially to Storage in the Definitions or at http://relays.te.com/appnotes/ Dimensions 26.1 0.4 1 form C, 1 CO 1 form A, 1 NO 8.5 0.2 21.1 0.4 *) *) Assembly and positioning aid TE1091-B1 3.4 0.1 TE1086-A1 3.4 0.1 *) Terminals 4 to be bridged 21.2 0.3 Mounting Hole Layout Bottom view on solder pins 16.0 0.3 3.0 0.5 *) 2.5 - 3.0 10.2 0.2 0.55 0.25 6.0 0.2 *) additional tin tops max. 1.5 mm o 1.3 +0.1 o 2.3 +0.1 3.4 0.6 6.6 0.3 12.1 0.1 TE0579-I2 Terminals tinned 2.2 0.1 3.3 0.1 o 2.1 +0.1 o 2.3 +0.1 o 2.3 +0.1 2.3 0.2 13.3 0.2 TE0580-L2 2 06-2014, Rev. 0614 www.te.com (c) 2014 Tyco Electronics Corporation, a TE Connectivity Ltd. company. Catalog and product specification according to IEC 61810-1 and to be used only together with the `Definitions' section. Catalog and product data is subject to the terms of the disclaimer and all chapters of the `Definitions' section, available at http://relays.te.com/definitions Catalog product data, `Definitions' section, application notes and all specifications are subject to change. Automotive Relays PCB Single Relays Power Relay K (Sealed) (Continued) Product code structure Type V23076 Typical product code V23076 -A 1 022 -C 13 3 Power Relay K, sealed Terminal A PCB Design 1 Single relay Coil 001 12VDC Contact type C Single contact Contact material 13 AgNi0.15 15 AgSnO2 (Special) Contact arrangement 2 1 form A, 1 NO Product code V23076-A1001-C133 V23076-A1001-D143 V23076-A3001-C132 V23076-A3001-D142 V23076-A3001-D1521) V23076-A1022-C133 V23076-A1022-D143 V23076-A3022-C132 V23076-A3022-D142 V23076-A3022-D1521) Terminal/Encl. PCB, sealed 3 Single relay 022 24VDC D Single contact 14 AgSnO2 3 1 form C, 1 CO Design Single relay Coil 12VDC 24VDC Contact Single Contact mat. AgNi0.15 AgSnO2 AgNi0.15 AgSnO2 AgSnO2 special AgNi0.15 AgSnO2 AgNi0.15 AgSnO2 AgSnO2 special Arrangement 1 form C, CO 1 form A, NO 1 form C, CO 1 form A, NO Part number 1393277-4 1393277-6 1-1393277-4 1-1393277-7 1-1414175-0 1393277-8 1393277-9 1-1393277-8 1-1393277-9 4-1904101-8 1) For indicator lamps. 06-2014, Rev. 0614 www.te.com (c) 2014 Tyco Electronics Corporation, a TE Connectivity Ltd. company. Catalog and product specification according to IEC 61810-1 and to be used only together with the `Definitions' section. Catalog and product data is subject to the terms of the disclaimer and all chapters of the `Definitions' section, available at http://relays.te.com/definitions Catalog product data, `Definitions' section, application notes and all specifications are subject to change. 3