1
06-2014, Rev. 0614
www.te.com
© 2014 Tyco Electronics Corporation,
a TE Connectivity Ltd. company.
Catalog and product specification according
to IEC 61810-1 and to be used only together
with the ‘Definitions’ section.
Catalog and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Catalog product data, ‘Definitions’ section,
application notes and all specifications are
subject to change.
Power Relay K (Sealed)
Automotive Relays
PCB Single Relays
n Limiting continuous current 45A
n Wide voltage range
n 24VDC coil versions available
Typical applications
ABS control, blower fans, car alarm, cooling fan, engine control, fuel pump,
hazard warning signal, heated front screen, heated rear screen, ignition,
lamps front/rear/fog light, interior lights, main switch/supply relay, seat
control, seatbelt pretensioner, sun roof, turn signal, valves, window lifter,
wiper control.
Contact Data
Typical applications Resistive/inductive Resistive/inductive Indicator lamps Headlights, Headlights
loads loads capacitive loads capacitive loads
Contact arrangement 1 form A, 1 NO 1 form C, 1 CO 1 form A, 1 NO 1 form A, 1 NO 1 form C, 1 CO
Rated voltage 12VDC 12VDC 12VDC 12VDC 12VDC
A/B (NO/NC) A/B (NO/NC)
Rated current 45A 45/30A 30A 40A 40/25A
Limiting continuous current
23°C 45A 45/30A 30A 40A 40/25A
85°C 30A 30/25A 25A 25A 25/20A
Limiting making current1) 100A 100/30A 120A3) 180A 180/60A
Limiting breaking current2) 60A 60/30A 60A 60A 60/30A
Contact material AgNi0.15 AgNi0.15 AgSnO2 AgSnO2 AgSnO2
Min. recommended contact load 1A at 5VDC4)
Initial voltage drop, at 10A, typ./max. 20/300mV
Operate/release time typ. 5/3ms5)
Electrical endurance >2x105 ops. >2x105 ops. >2.2x106 ops. >105 ops. >105 ops.
at 13.5VDC, 40A at 13.5VDC, 40A up to 8x21W up to 4x60W up to 4x60W
Mechanical endurance, DC coil >107 ops.
1) The values apply to a resistive or inductive load with suitable spark suppression and at maximum 13.5VDC for 12VDC or 27VDC for 24VDC load voltages.
2) For a load current duration of maximum 3s for a make/break ratio of 1:10.
3) Corresponds to a peak inrush current on initial actuation (cold filament).
4) See chapter Diagnostics of Relays in our Application Notes or consult the internet at http://relays.te.com/appnotes/
5) For unsuppressed relay coil. A low resistive suppression device in parallel to the relay coil increases the release time and reduces the lifetime caused by increased erosion and/or higher
risk of contact tack welding.
Max. DC load breaking capacity
Load limit curve 1: arc extinguishes, during transit time (changeover contact).
Load limit curve 2: safe shutdown, no stationary arc (make contact).
Load limit curves measured with low inductive resistors verified for 1000 switching events.
F076_fcw2b
Does not take into account
the temperature rise due to
the contact current
E = pre-energization
TE0555-6
Does not take into account the temperature rise due to the contact current
E = pre-energization
Coil operating range