Product Specification G64240x05 series Crystal Clear Technology sdn. bhd. 16Jalan TP5--Taman Perindustrian Sime UEP 47600 Subang Jaya--Selangor DE Malaysia. T: +603 80247099 F: +603 80247098 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G64240x05xxx00 REV 2.0 1.0 Table of Contents Page 1. Table of Contents 1 2. Record of revision 2 3. General specification 3 4. Absolute maximum ratings 4 5. Electrical characteristics 4 6. Environmental requirement 5 7. LCD specification 6~8 8. Interface 9 9. Functional Description 10 ~ 11 10. Instructions 12 11. Block Diagram and Power Supply 13 12. Quality assurance 14 ~ 15 13. Precautions in use LCM 16 ~ 17 14. Outline drawing 18 1 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G64240x05xxx00 REV 2.0 2.0 Record of revision Rev Date 1.0 09/10/09 2.0 01/12/16 Item Page Comment Initial Release 3 3 Change IC Originator Checked By SCChong Azhar Azhar Azhar 2 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G64240x05xxx00 REV 2.0 3.0 General specification Display format: Graphics 240 (w) x 64 (h) dots Dot size: 0.48 (w) x 0.48 (h) mm Dot pitch: 0.53 (w) x 0.53 (h) mm View area: 132.6 (w) x 39.0 (h) mm Active area: 127.15 (w) x 33.87 (h) mm General dimensions: 180.0 (w) x 65.0 (h) x 15.0 max (t) mm Controller/Driver: UCi6963 and UCi0086 or equivalent. Interface: Parallel Driving method: 1/64 duty, 1/9 bias G 6 4 2 4 0 X 0 5 X X W 0 0 MODEL NUMBER STD. GRAPHIC : No. of row followed by no. of column BACKLIGHT MODE A : Side Led Backlight (Amber) B : Side Led Backlight (Blue) G : Side Led Backlight (Green) N : Without Backlight R : Side Led Backlight (Red) S : Side Led Backlight (Yellow Green) W : Side Led Backlight (White) MODULE VERSION Version from 01 to 99 LCD MODE Y : Yellow Green (STN) G : Grey (STN) B : Black White (FSTN) N : Negative (FSTN) Blue ( Single Retardation ) U : Negative (FSTN) Black/White ( Double Retardation ) S : Negative (STN) P : Positive (HTN) VIEWING ANGLE T : Top view ( 12 O'clock ) B : Bottom view ( 6 O'clock ) OPERATING TEMPERATURE N : Operating Temperature (0C to +50C ), Storage Temperature (-20C to +70C ) W : Operating Temperature (-10C to +60C ), Storage Temperature (-20C to +70C ) SEMI - CUSTOMISE (MINOR CHANGES FROM STANDARD MODEL) 00 - STANDARD MODEL REFER TO FACTORY FOR OTHER VERSIONS. TERM AND CONDITION APPLY 3 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G64240x05xxx00 REV 2.0 4.0 NO 1. 2. 3. 4. 5.0 NO 1. 2. 3. 4. 5.1 Absolute maximum rating (at Vss = 0V, ambient temperature = 25C) ITEM Power Supply Voltage (Logic) Power Supply Voltage (LCD Driver) Operating Temperature Storage Temperature SIMBOL VDD - VSS VDD - V0 Top Tst MIN MAX 0 7.0 13.5 Refer page 3 Refer page 3 UNIT V V C C Electrical characteristics ITEM Power Supply Voltage (Logic) Power Supply Voltage (VLCD) Input Voltage Current Supply SYMBOL CONDITION MIN TYP MAX UNI T VDD - VSS - 3.0 - 5.5 V VDD-V0 25C VIH VIL - 0.8VDD 0 - VDD 0.2VDD V IDD VDD - VSS = 5V VDD - V0 = 12V - 3.0 5.0 mA 12.05% V Backlight Options FORWARD VOLTAGE FORWARD CURRENT MIN (V) (mA) BRIGHTNESS Min Typ. Max Min Typ. Max (cd/m2) * 1. Yellow Green 5.0 100 250 75 2. White 5.0 45 60 60 3. Pure Green 5.0 45 60 60 *Note: 1. Brightness measured at backlight surface. 2. On LCD surface, brightness is only about 10% to 15% of backlight brightness. 3. Lifetime of backlight: For YG = 50K hrs. For White and pure green = 20K hrs NO COLOR 4 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G64240x05xxx00 REV 2.0 6.0 NO Environmental requirements ITEM CONDITION 1. High Temperature Storage +802C / 96Hours 2. Low Temperature Storage -302C / 96Hours 3 High Temperature Operating +702C / 96Hours 4 Low Temperature Operating -202C / 96Hours 5 Temperature Cycle Operating -202C ~ 25C ~ +70C x 10 Cycles (30min) (5 min) (30min) 6 Humidity Test (Operating) 40C, 905%RH, 96Hrs 7 LCD Lifetime 50 000 Hours (Excluding Backlight) Inspection after 2 ~ 4 hours storage at room temperature, the sample shall be free from defects: 1. Air bubble in LCD 2. Seal leak 3. Non-Display 4. Missing segment 5. Glass crack 6. Current Idd should be lower than double of initial Idd. Note: 1. The background on LCD has the possibility to be changed in different temperature range. 2. The test samples should be applied to only one test item. 3. Sample size for each test item is 1 ~ 5 pcs. 5 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G64240x05xxx00 REV 2.0 7.0 LCD specification 7.1 Electro-optical characteristics (at ambient temperature = 25C) LCD TYPE UNIT STN -VE BLUE/ PURP LE FSTN +VE B/W FSTN -VE BLUE FSTN VE TRUE B/W FSTN -VE TRI AXIS NO ITEM SYMBOL CONDITION 1 Operating Voltage (Volt) VLCD =0 Cr = max 2 Viewing Angle (Deg) x 1 x 2 y 1 y 2 CR 2 VLCD = 12.0V +25 -25 -30 +30 +20 -20 -25 +25 +35 -35 -35 +35 +25 -25 -30 +30 +35 -35 -35 +35 +35 -40 -35 +35 +40 -40 -50 +30 7.1.2 3 Contrast Ratio CR = 00 VLCD =12.0V 3.0 2.3 6.0 3.0 6.0 20 20 7.1.3 Response Time (msec) Rise Time (Tr) Decay Time (Td) 4 = 00 STN YG STN GREY 12.0 5% REF. 7.1.1 200 7.1.4 = 00 250 Note: 1. Viewing angle data is based on bottom view product by default. Should it be a top view product, values are then swap. 2. Contrast ratio is based on typical data when using white colour as backlight. 3. Equipment Used Eldim: Ez Contrast 120R , Spot Size = 2mm 6 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G64240x05xxx00 REV 2.0 NO CHARACTERISTICS 7.1.1 Definition of Operating Voltage (VLCD) DEFINITIONS VLCD 1/F VLCD : Operating Voltage F : Frame Frequency 7.1.2 TOP Definition of Viewing Angle REAR LEFT RIGHT FRONT BOTTOM REAR (y2) LEFT(x2) RIGHT(x1) FRONT (y1) 7 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G64240x05xxx00 REV 2.0 7.1.3 Definition of Contrast Ratio NON-SELECT WAVE BRIGHTNESS (%) SELECT WAVE b a OPERATION VOLTAGE Contrast Ratio = Brightness of non-selected state (b) Brightness of selected state (a) Conditions (a) Operating Voltage: VLCD (b) Temperature: 25C (c) Viewing Angle, = 0o 7.1.4 Response Time Luminance (%) 90 10 Td Tr Time Tr: Measured between 10% and 90% of LCD segment maximum response with VON. Td: With voltage switches to zero and the instant LCD segment reaches 10% of its maximum response. 8 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G64240x05xxx00 REV 2.0 8.0 Interface 8.1 Controller UCi6963 8.2 Display Driver UCi0086 8.3 Duty Cycle 1/64 8.4 Pin-out Assignments Pin No Symbol Description 1 FG Frame ground 2 VSS Ground terminal of module 3 VDD Supply terminal of module 4 VO Power supply for Liquid Crystal Drive 5 R/W Data Write 6 RD Data Read 7 CE Chip Enable 8 C/D H: Instruction , L: Data 9 NC Not Connected 10 Reset Reset signal 11 to 18 D0 to D7 19 FS Bi-directional Data Bus. Data Transfer is performed once, thru D0 to D7 Pin for selection of number of column 20 VOUT Negative output voltage from module 21 SLA LED backlight power supply. 22 SLK LED backlight ground. *Font interface format selection : Font size 5x8 6x8 7x8 8x8 J1 Used NC Used NC J2 NC Used NC Used Pin FS High High Low Low Note: NC = Not Connected 9 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G64240x05xxx00 REV 2.0 9.0 Functional Descriptions 9.1 Display Control Timing Waveform and Characteristics Timing Characteristics between MPU and UCi6963 10 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G64240x05xxx00 REV 2.0 9.2 Relationship between character code and pattern CG ROM TYPE 0101 CG ROM TYPE 0201 11 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G64240x05xxx00 REV 2.0 10. Instruction Set COMMAND REGISTER SETTING SET CONTROL WORD MODE SET DISPLAY MODE CURSOR PATTERN SELECT DATA AUTO READ / WRITE DATA READ / WRITE SCREEN PEEK SCREEN COPY BIT SET / RESET CODE 00100001 00100010 00100100 01000000 01000001 01000010 01000011 1000X000 1000X001 1000X011 1000X100 10000XXX 10001XXX 10010000 1001XX10 1001XX11 100101XX 100110XX 100111XX 10100000 10100001 10100010 10100011 10100100 10100101 10100110 10100111 10110000 10110001 10110010 11000000 11000001 11000010 11000011 11000100 11000101 11100000 11101000 11110XXX 11111XXX 1111X000 1111X001 1111X010 1111X011 1111X100 1111X101 1111X110 1111X111 D1 X address Data Low address Low address Columns Low address Columns - D2 Y address 00H High address High address 00H High address 00H - Data Data Data - - - -- -- FUNCTION Set Cursor Pointer Set Offset Register Set Address Pointer Set Text Home Address Set Text Area Set Graphic Home Address Set Graphic Area OR mode EXOR mode AND mode Text Attribute mode Internal CG ROM mode External CG RAM mode Display off Cursor on, blink off Cursor on, blink on Text on, graphic off Text off, graphic on Text on, graphic on 1-line cursor 2-line cursor 3-line cursor 4-line cursor 5-line cursor 6-line cursor 7-line cursor 8-line cursor Set Data Auto Write Set Data Auto Read Auto Reset Data Write and Increment ADP Data Read and Increment ADP Data Write and Decrement ADP Data Read and Decrement ADP Data Write and Nonvariable ADP Data Read and Nonvariable ADP Screen Peek Screen Copy Bit Reset Bit set Bit 0 (LSB) Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7 (MSB) 12 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G64240x05xxx00 REV 2.0 11. Block Diagram and Power Supply Block Diagram VDD 5V VSS Vout Vo 5.0V SLA SLK Power Supply 13 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G64240x05xxx00 REV 2.0 12.0 Quality Assurance 12.1 ZONE DEFINITION ZONE A EFFECTIVE VIEWING AREA ZONE B (Outside Viewing Area) ZONE C (Sealing Area) 12.1.1 Defect Category Black Spot, White Spot and Foreign Material Black Spot, White Spot and Foreign Material Defect Description Black Spot, White Spot and Foreign Material Criterion Zone / Dimension Drawing Specification Acceptable No. A B C NC NC NC 0.10 0.30 mm NC: No count 0 0 NC D < 0.10mm B A D = (A + B)/2 D: Mean Diameter of Defect 12.1.2 Defect Category Line shape and scratches 12.1.3 Defect Category Pin Hole Line Shape and Scratches Defect Description Line shape and scratches Criterion Zone /Dimension X Y <0.01mm < 2 mm < 0.02mm <1 mm < 0.0 2mm Drawing Specification Acceptable No. A B C NC NC NC 1 1 NC 1 2 NC Pin Hole Defect Description Pin hole / void at light up segment Criterion Drawing Specification D < 0.20mm within 1 part/segment B A D = (A + B)/2 14 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G64240x05xxx00 REV 2.0 12.1.4 Polarizer Bubble/Foreign Material Defect Category Defect Description Polarizer bubble / Foreign material Criterion Zone / Dimension D 0.15mm 0.15 < D 0.30mm 0.30 < D 0.50mm 0.50 < D 1.0mm Drawing Specification Acceptable No. A B C NC NC NC 3 5 NC 2 3 NC 0 1 B A D = (A + B)/2 NC NC: No count D: Mean Diameter of Defect Accept - if air bubble at the seal area does not propagate into effective viewing area Note: Total defects shall not exceed five 15 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G64240x05xxx00 REV 2.0 13. Precaution for using LCM 1. Liquid Crystal Display (LCD) LCD is made up of glass, organic sealant, organic fluid and polymer based polarizers. The following precautions should be taken when handling. a) Keep the temperature within the range of use and storage. Excessive temperature and humidity could cause polarization degradation, polarizer peel off or bubble. b) Do not contact the exposed polarizer with anything harder than HB pencil lead. To clean dust off the display surface, wipe gently with cotton, chamois or other soft material soaked in petroleum benzene. c) Wipe off saliva or water drops immediately. Contact with water over a long period of time may cause polarizer deformation or colour fading, while an active LCD with water condensation on its surface will cause corrosion of ITO electrodes. d) Glass can be easily chipped or cracked from rough handling, especially at corners and edges. e) Do not drive LCD with DC voltage. 2. Liquid Crystal Display Modules. 2.1 Mechanical Considerations LCM are assembled and adjusted with a high degree of precision. Avoid excessive shocks and do not make any alterations or modification. The following should be noted. a) Do not tamper in any way with the tabs on the metal frame. b) Do not modify the PCB by drilling extra holes, changing its outline, moving its component or modifying its pattern. c) Do not touch the elastomer connector, especially at conductor area. d) When mounting a LCM make sure that the PCB is not under any stress such as bending or twisting. Elastomer contacts are very delicate and missing pixels could result from slight dislocation of any of the elements. e) Avoid pressing on the metal bezel, otherwise the elastomer connector could be deformed and lose contact, resulting in missing pixels. 2.2 Static Electricity LCM contains CMOS LSI's and the same precaution for such devices should apply, namely a) The operator should be grounded whenever he/she comes into contact with the module. Never touch any of the conductive parts such as the LSI pads, the copper leads on the PCB and the interface terminals with any parts of the human body. b) The modules should be kept in antistatic bags or other antistatic containers. c) Only properly grounded soldering irons should be used. d) If an electric screwdriver is used, it should be well grounded and shielded from spark commutator. e) The normal static prevention measures should be observed for work clothes and working benches, the latter conductive (rubber) mat is recommended. f) Since dry air is inductive to statics, a relative humidity of 50-60% is recommended. 2.3 Operation a) Viewing angle varies with the change of liquid crystal driving voltage (VLCD). VLCD has to be adjusted to show the best contrast. b) It is a necessary condition to drive LCD's within the specified voltage limit since at the higher voltage limit this can result in shorter LCD life. An electrochemical reaction due to direct current causes LCD's undesirable deterioration, so that the use of direct current drive should be avoided. c) Response times will be delayed at lower temperature than the operating temperature range and on the other hand, at higher temperature LCD's show darker color in them. However those phenomena do not mean a malfunction or out of order with the LCD's which will recover in the specified operating temperature. d) If the display area is pushed hard during operation, the display will become abnormal. However, it will return to normal if it is turned off and then back on. 16 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G64240x05xxx00 REV 2.0 e) A slight dew depositing on terminals is a cause for electro-chemical reaction resulting in terminal open circuit. Usage under the maximum operating temperature, 50%RH or less is required. f) Input logic voltage before apply analog high voltage such as LCD driving voltage when power on. Remove analog high voltage before logic voltage when power off the module. Input each signal after the positive/negative voltage becomes stable. g) It is advisable to keep the temperature within the specified range for use and storage. Polarization degradation, bubble generation or polarizer peel-off may occur with high temperature and high humidity. 2.4 Soldering a) Solder only to the I/O terminals. b) Use only soldering irons with proper grounding and no leakage. c) Soldering temperature: 280 C d) Soldering time: 3 to 4 sec e) Use eutectic solder with resin flux fill. f) If flux is used, the LCD surface should be covered to avoid flux spatters. Flux residue should be removed afterwards. 2.5 Storage If any fluid leaks out of the damage glass cell, wash off any human part that comes into contact with soap and water. Never swallow the fluid. The toxicity is extremely low but caution should be exercised at all time. 3. Limited Warranty Unless otherwise agreed between Crystal Clear Technology and customer, Crystal Clear Technology will replace or repair any of its LCD and LCM which is found to be defective electrically and visually when inspected in accordance with Crystal Clear Technology acceptance standards, for a period of one year from date of shipment. Confirmation of such date shall be based on freight documents. The warranty liability of Crystal Clear Technology is limited to repair and/or replacement on the terms set forth above. Crystal Clear Technology will not responsible for any subsequent or consequential events. 4. Return LCM under Warranty No warranty can be granted if the precautions stated above have been disregarded. The typical examples of violations are: i. Broken LCD glass ii. PCB eyelet's damaged or modified iii. PCB conductors damaged iv. Circuit modified in any way, including addition of components. v. PCB tampered with by grinding, engraving or painting varnish. vi. Soldering to, or modifying the bezel in any manner. Module repairs will be invoiced to customer upon mutual agreement. Modules must be returned with sufficient description of failure or defects. Any connectors or cable installed by customer must be removed completely without damaging the PCB eyelet's, conductors and terminals. 17 CRYSTAL CLEAR TECHNOLOGY SDN. BHD. Spec. No: G64240x05xxx00 REV 2.0 2 3 4 A 5 6 7 8 W2 1.6 B W1 B 1 C 54.0 (65.0) 65.00.5 58.00.3 54.0 39.0 33.87 25.4 2 C 11 10 A 180.00.5 176.00.5 153.60.3 132.6 127.15 2.0 13.20.5 23.70.3 26.430.3 9 13.0 5.5 1 GRAPHICS 64 X 240 DOTS 21 3.0 22 HOLES 22 - O1.0 D 4- 3.50.5 5.50.3 13.00.3 15.60.3 R1 .5 D 0.53 0.48 E 0.53 0.48 E F F NOTE : 1. GENERAL TOLERANCE TO BE 0.3 2. BEZEL : COATING IN BLACK G G MODEL NAME NO MATERIAL PART NAME MECHANICAL SPECIFICATION Crystal-Clear Technology H VERSION W1 W2 NO/EL BACKLIGHT 5.000.5 10.0 MAX LED BACKLIGHT 8.000.5 13.0 MAX 16, JLN TP5, TMN PERINDUSTRIAN SIME UEP, 47500 SUBANG JAYA, SELANGOR DARUL EHSAN. APPROVED CHECKED 08-10-2009 1 2 3 4 5 6 7 8 DRAWING NUMBER DRAWN azhar 9 UNIT : MM SCALE 1 : 1 REMARKS G64240x05xxx00 10 SHEET 1 1 11 REV. 1 H 18 Crystal Clear Technology 16 Jalan TP5--Taman Perindustrian Sime UEP 47600 Subang Jaya--Selangor DE Malaysia