Product Specification
G64240x05 series
Crystal Clear Technology sdn. bhd.
16Jalan TP5Taman Perindustrian Sime UEP
47600 Subang Jaya—Selangor DE
Malaysia. T: +603 80247099 F: +603 80247098
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64240x05xxx00 REV 2.0
1
1.0 Table of Contents
Page
1. Table of Contents 1
2. Record of revision 2
3. General specification 3
4. Absolute maximum ratings 4
5. Electrical characteristics 4
6. Environmental requirement 5
7. LCD specification 6 ~ 8
8. Interface 9
9. Functional Description 10 ~ 11
10. Instructions 12
11. Block Diagram and Power Supply 13
12. Quality assurance 14 ~ 15
13. Precautions in use LCM 16 ~ 17
14. Outline drawing 18
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64240x05xxx00 REV 2.0
2
2.0 Record of revision
Rev Date Item Page Comment Originator Checked By
1.0
2.0
09/10/09
01/12/16
3
3
Initial Release
Change IC
SCChong
Azhar
Azhar
Azhar
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64240x05xxx00 REV 2.0
3
3.0 General specification
Display format: Graphics 240 (w) x 64 (h) dots
Dot size: 0.48 (w) x 0.48 (h) mm
Dot pitch: 0.53 (w) x 0.53 (h) mm
View area: 132.6 (w) x 39.0 (h) mm
Active area: 127.15 (w) x 33.87 (h) mm
General dimensions: 180.0 (w) x 65.0 (h) x 15.0 max (t) mm
Controller/Driver: UCi6963 and UCi0086 or equivalent.
Interface: Parallel
Driving method: 1/64 duty, 1/9 bias
OPERATING TEMPERATURE
SEMI - CUSTOMISE (MINOR CHANGES FROM STANDARD MODEL)
R : Side Led Backlight (Red)
S : Side Led Backlight (Yellow Green)
W : Side Led Backlight (White)
Y : Yellow Green (STN)
G : Grey (STN)
B : Black White (FSTN)
N : Negative (FSTN) Blue ( Single Retardation )
U : Negative (FSTN) Black/White ( Double Retardation )
S : Negative (STN)
P : Positive (HTN)
BACKLIGHT MODE
Version from 01 to 99
MODULE VERSION
A : Side Led Backlight (Amber)
B : Side Led Backlight (Blue)
G : Side Led Backlight (Green)
N : Without Backlight
B : Bottom view ( 6 O'clock )
T : Top view ( 12 O'clock )
LCD MODE
VIEWING ANGLE
MODEL NUMBER
G2 4 0 0 5 W 0 06 4
STD. GRAPHIC : No. of row followed by no. of column
X X X
00 - STANDARD MODEL
REFER TO FACTORY FOR OTHER VERSIONS. TERM AND CONDITION APPLY
W : Operating Temperature (-10°C to +60°C ), Storage Temperature (-20°C to +70°C )
N : Operating Temperature (0°C to +50°C ), Storage Temperature (-20°C to +70°C )
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64240x05xxx00 REV 2.0
4
4.0 Absolute maximum rating (at Vss = 0V, ambient temperature = 25°C)
NO ITEM SIMBOL MIN MAX UNIT
1. Power Supply Voltage (Logic) V
DD
- V
SS
0 7.0 V
2. Power Supply Voltage (LCD Driver)
V
DD
– V
0
- 13.5 V
3. Operating Temperature T
op
Refer page 3
°
C
4. Storage Temperature T
st
Refer page 3
°
C
5.0 Electrical characteristics
NO ITEM
SYMBOL
CONDITION
MIN TYP MAX
UNI
T
1. Power Supply
Voltage (Logic) V
DD
– V
SS
- 3.0 - 5.5 V
2. Power Supply
Voltage (V
LCD
) V
DD
-V
0
25°C 12.0±5% V
3. Input Voltage V
IH
- 0.8V
DD
- V
DD
V
V
IL
0 - 0.2V
DD
4. Current Supply I
DD
V
DD
- V
SS =
5V
V
DD
– V
0
=
12V
- 3.0 5.0 mA
5.1 Backlight Options
NO COLOR
FORWARD VOLTAGE
(V)
FORWARD CURRENT
(mA)
MIN
BRIGHTNESS
(cd/m2) * Min Typ. Max Min Typ. Max
1. Yellow Green - 5.0 - - 100 250 75
2. White - 5.0 - - 45 60 60
3. Pure Green - 5.0 - - 45 60 60
*Note: 1. Brightness measured at backlight surface.
2. On LCD surface, brightness is only about 10% to 15% of backlight brightness.
3. Lifetime of backlight: For YG = 50K hrs. For White and pure green = 20K hrs
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64240x05xxx00 REV 2.0
5
6.0 Environmental requirements
NO
ITEM CONDITION
1. High Temperature Storage +80±2°C / 96Hours
Inspection after 2 ~ 4 hours storage at
room temperature, the sample shall be
free from defects:
1. Air bubble in LCD
2. Seal leak
3. Non-Display
4. Missing segment
5. Glass crack
6. Current Idd should be lower
than double of initial Idd.
2. Low Temperature Storage -30±2°C / 96Hours
3 High Temperature Operating +70±2°C / 96Hours
4 Low Temperature Operating -20±2°C / 96Hours
5 Temperature Cycle Operating -20±2°C ~ 25°C ~ +70±°C x 10 Cycles
(30min) (5 min) (30min)
6 Humidity Test (Operating) 40°C, 90±5%RH, 96Hrs
7 LCD Lifetime 50 000 Hours (Excluding Backlight)
Note:
1. The background on LCD has the possibility to be changed in different
temperature range.
2. The test samples should be applied to only one test item.
3. Sample size for each test item is 1 ~ 5 pcs.
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64240x05xxx00 REV 2.0
6
7.0 LCD specification
7.1 Electro-optical characteristics (at ambient temperature = 25°C)
NO
ITEM
SYMBOL CONDITION
LCD TYPE
UNIT
REF.
STN
YG
STN
GREY
STN
-VE
BLUE/
PURP
LE
FSTN
+VE
B/W
FSTN
–VE
BLUE
FSTN -
VE
TRUE
B/W
FSTN
-VE
TRI
AXIS
1
Operating
Voltage
(Volt)
V
LCD
θ = 0
Cr = max 12.0 ± 5% 7.1.1
2
Viewing
Angle
(Deg)
θ
x 1 CR 2
V
LCD
=
12.0V
+25 +20 +35 +25 +35 +35 +40
7.1.2
θ
x 2 -25 -20 -35 -25 -35 -40 -40
θ
y 1 -30 -25 -35 -30 -35 -35 -50
θ
y 2 +30 +25 +35 +30 +35 +35 +30
3 Contrast
Ratio CR
θ
= 0
0
V
LCD
=12.0V
3.0 2.3 6.0 3.0 6.0 20 20 7.1.3
4
Response
Time
(msec)
Rise
Time
(Tr)
θ = 0
0
200
7.1.4
Decay
Time
(Td)
θ = 0
0
250
Note:
1. Viewing angle data is based on bottom view product by default. Should it be a
top view product, values are then swap.
2. Contrast ratio is based on typical data when using white colour as backlight.
3. Equipment Used Eldim: Ez Contrast 120R , Spot Size = 2mm
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64240x05xxx00 REV 2.0
7
NO CHARACTERISTICS DEFINITIONS
7.1.1
Definition of Operating
Voltage (V
LCD
)
V
LCD
1/F
V
LCD
: Operating Voltage
F : Frame Frequency
7.1.2
Definition of Viewing
Angle
TOP
θ REAR
LEFT RIGHT
FRONT
BOTTOM
REAR (θy2)
LEFT(θx2) RIGHT(θx1)
FRONT (θy1)
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64240x05xxx00 REV 2.0
8
7.1.3
Definition of Contrast
Ratio
NON-SELECT WAVE
BRIGHTNESS (%)
SELECT WAVE
b
a
OPERATION VOLTAGE
Contrast Ratio = Brightness of non-selected state (b)
Brightness of selected state (a)
Conditions
(a) Operating Voltage: V
LCD
(b) Temperature: 25°C
(c) Viewing Angle, θ = 0
o
7.1.4
Response Time
Luminance
(%)
90
10
Tr: Measured between 10% and 90% of LCD segment
maximum response with V
ON.
Td: With voltage switches to zero and the instant LCD
segment reaches 10% of its maximum response.
Td
Tr
Time
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64240x05xxx00 REV 2.0
9
8.0 Interface
8.1 Controller UCi6963
8.2 Display Driver UCi0086
8.3 Duty Cycle 1/64
8.4 Pin-out Assignments
Pin No Symbol Description
1 FG Frame ground
2 V
SS
Ground terminal of module
3 V
DD
Supply terminal of module
4 V
O
Power supply for Liquid Crystal Drive
5 R/W Data Write
6 RD Data Read
7 CE Chip Enable
8 C/D H: Instruction , L: Data
9 NC Not Connected
10 Reset Reset signal
11 to 18 D0 to D7 Bi-directional Data Bus. Data Transfer is performed
once, thru D0 to D7
19 FS Pin for selection of number of column
20 V
OUT
Negative output voltage from module
21 SLA LED backlight power supply.
22 SLK LED backlight ground.
*Font interface format selection :
Font size
J1
J2
Pin FS
5x8
Used
NC
High
6x8
NC
Used High
7x8 Used NC Low
8x8
NC
Used
Low
Note: NC = Not Connected
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64240x05xxx00 REV 2.0
10
9.0 Functional Descriptions
9.1 Display Control Timing Waveform and Characteristics
Timing Characteristics between MPU and UCi6963
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64240x05xxx00 REV 2.0
11
9.2 Relationship between character code and pattern
CG ROM TYPE 0101
CG ROM TYPE 0201
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64240x05xxx00 REV 2.0
12
10. Instruction Set
COMMAND CODE D1 D2 FUNCTION
REGISTER
SETTING
00100001
00100010
00100100
X address
Data
Low address
Y address
00H
High address
Set Cursor Pointer
Set Offset Register
Set Address Pointer
SET CONTROL
WORD
01000000
01000001
01000010
01000011
Low address
Columns
Low address
Columns
High address
00H
High address
00H
Set Text Home Address
Set Text Area
Set Graphic Home Address
Set Graphic Area
MODE SET 1000X000
1000X001
1000X011
1000X100
10000XXX
10001XXX
-
-
-
-
-
-
-
-
-
-
-
-
OR mode
EXOR mode
AND mode
Text Attribute mode
Internal CG ROM mode
External CG RAM mode
DISPLAY MODE 10010000
1001XX10
1001XX11
100101XX
100110XX
100111XX
-
-
-
-
-
-
-
-
-
-
-
-
Display off
Cursor on, blink off
Cursor on, blink on
Text on, graphic off
Text off, graphic on
Text on, graphic on
CURSOR PATTERN
SELECT
10100000
10100001
10100010
10100011
10100100
10100101
10100110
10100111
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
1-line cursor
2-line cursor
3-line cursor
4-line cursor
5-line cursor
6-line cursor
7-line cursor
8-line cursor
DATA AUTO READ
/ WRITE
10110000
10110001
10110010
-
-
-
-
-
-
Set Data Auto Write
Set Data Auto Read
Auto Reset
DATA READ /
WRITE
11000000
11000001
11000010
11000011
11000100
11000101
Data
-
Data
-
Data
-
-
-
-
-
Data Write and Increment ADP
Data Read and Increment ADP
Data Write and Decrement ADP
Data Read and Decrement ADP
Data Write and Nonvariable ADP
Data Read and Nonvariable ADP
SCREEN PEEK 11100000 - - Screen Peek
SCREEN COPY 11101000 Screen Copy
BIT SET / RESET 11110XXX
11111XXX
1111X000
1111X001
1111X010
1111X011
1111X100
1111X101
1111X110
1111X111
-
-
-
-
-
--
-
-
-
-
-
-
-
-
-
--
-
-
-
-
Bit Reset
Bit set
Bit 0 (LSB)
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7 (MSB)
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64240x05xxx00 REV 2.0
13
11. Block Diagram and Power Supply
Block Diagram
5V
5.0V
Power Supply
SLA
SLK
V
DD
V
SS
V
out
Vo
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64240x05xxx00 REV 2.0
14
12.0 Quality Assurance
12.1 ZONE DEFINITION
12.1.1 Black Spot, White Spot and Foreign Material
Defect
Category Defect Description Criterion Drawing Specification
Black Spot,
White Spot
and Foreign
Material
Black Spot, White
Spot and Foreign
Material
Zone / Acceptable No.
Dimension A B C
D < 0.10mm NC NC NC
0.10<D < 0.20mm 3 3 NC
0.20 < D < 0.30mm 1 2 NC
D > 0.30 mm 0 0 NC
NC: No count
D: Mean Diameter of Defect
12.1.2 Line Shape and Scratches
Defect
Category Defect Description Criterion Drawing Specification
Line shape
and scratches
Line shape and
scratches
Zone /Dimension Acceptable No.
X Y A B C
-
<0.01mm
NC NC NC
< 2 mm
< 0.02mm
1 1 NC
<1 mm
< 0.0 2mm
1 2 NC
12.1.3 Pin Hole
Defect
Category
Defect Description Criterion Drawing Specification
Pin Hole Pin hole / void at
light up segment D < 0.20mm within 1 part/segment
A
B
D = (A + B)/2
A
B
D = (A + B)/2
EFFECTIVE VIEWING AREA
ZONE A
ZONE B
(Outside Viewing Area)
ZONE C
(Sealing Area)
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64240x05xxx00 REV 2.0
15
12.1.4 Polarizer Bubble/Foreign Material
Defect
Category
Defect Description Criterion Drawing Specification
Polarizer bubble /
Foreign material
Zone / Acceptable No.
Dimension A B C
D ≤ 0.15mm NC NC NC
0.15 < D ≤ 0.30mm 3 5 NC
0.30 < D ≤ 0.50mm 2 3 NC
0.50 < D ≤ 1.0mm 0 1 NC
NC: No count
D: Mean Diameter of Defect
Accept - if air bubble at the seal area does
not propagate into effective viewing area
Note: Total defects shall not exceed five
A
B
D = (A + B)/2
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64240x05xxx00 REV 2.0
16
13. Precaution for using LCM
1.
Liquid Crystal Display (LCD)
LCD is made up of glass, organic sealant, organic fluid and polymer based polarizers. The following
precautions should be taken when handling.
a) Keep the temperature within the range of use and storage. Excessive temperature and humidity
could cause polarization degradation, polarizer peel off or bubble.
b) Do not contact the exposed polarizer with anything harder than HB pencil lead. To clean dust
off the display surface, wipe gently with cotton, chamois or other soft material soaked in
petroleum benzene.
c) Wipe off saliva or water drops immediately. Contact with water over a long period of time
may cause polarizer deformation or colour fading, while an active LCD with water
condensation on its surface will cause corrosion of ITO electrodes.
d) Glass can be easily chipped or cracked from rough handling, especially at corners and edges.
e) Do not drive LCD with DC voltage.
2.
Liquid Crystal Display Modules.
2.1 Mechanical Considerations
LCM are assembled and adjusted with a high degree of precision. Avoid excessive shocks and
do not make any alterations or modification. The following should be noted.
a) Do not tamper in any way with the tabs on the metal frame.
b) Do not modify the PCB by drilling extra holes, changing its outline, moving its
component or modifying its pattern.
c) Do not touch the elastomer connector, especially at conductor area.
d) When mounting a LCM make sure that the PCB is not under any stress such as
bending or twisting. Elastomer contacts are very delicate and missing pixels could
result from slight dislocation of any of the elements.
e) Avoid pressing on the metal bezel, otherwise the elastomer connector could be
deformed and lose contact, resulting in missing pixels.
2.2 Static Electricity
LCM contains CMOS LSI’s and the same precaution for such devices should apply, namely
a) The operator should be grounded whenever he/she comes into contact with the module.
Never touch any of the conductive parts such as the LSI pads, the copper leads on the
PCB and the interface terminals with any parts of the human body.
b) The modules should be kept in antistatic bags or other antistatic containers.
c) Only properly grounded soldering irons should be used.
d) If an electric screwdriver is used, it should be well grounded and shielded from spark
commutator.
e) The normal static prevention measures should be observed for work clothes and working
benches, the latter conductive (rubber) mat is recommended.
f) Since dry air is inductive to statics, a relative humidity of 50-60% is recommended.
2.3 Operation
a) Viewing angle varies with the change of liquid crystal driving voltage (VLCD).
VLCD has to be adjusted to show the best contrast.
b) It is a necessary condition to drive LCD's within the specified voltage limit since at the
higher voltage limit this can result in shorter LCD life. An electrochemical reaction due to
direct current causes LCD's undesirable deterioration, so that the use of direct current
drive should be avoided.
c) Response times will be delayed at lower temperature than the operating temperature range
and on the other hand, at higher temperature LCD's show darker color in them. However
those phenomena do not mean a malfunction or out of order with the LCD's which
will recover in the specified operating temperature.
d) If the display area is pushed hard during operation, the display will become abnormal.
However, it will return to normal if it is turned off and then back on.
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64240x05xxx00 REV 2.0
17
e) A slight dew depositing on terminals is a cause for electro-chemical reaction resulting in
terminal open circuit. Usage under the maximum operating temperature, 50%RH or less
is required.
f) Input logic voltage before apply analog high voltage such as LCD driving voltage when
power on. Remove analog high voltage before logic voltage when power off the module.
Input each signal after the positive/negative voltage becomes stable.
g) It is advisable to keep the temperature within the specified range for use and storage.
Polarization degradation, bubble generation or polarizer peel-off may occur with high
temperature and high humidity.
2.4 Soldering
a) Solder only to the I/O terminals.
b) Use only soldering irons with proper grounding and no leakage.
c) Soldering temperature: 280 °C
d) Soldering time: 3 to 4 sec
e) Use eutectic solder with resin flux fill.
f) If flux is used, the LCD surface should be covered to avoid flux spatters. Flux residue
should be removed afterwards.
2.5 Storage
If any fluid leaks out of the damage glass cell, wash off any human part that comes into
contact with soap and water. Never swallow the fluid. The toxicity is extremely low but
caution should be exercised at all time.
3.
Limited Warranty
Unless otherwise agreed between Crystal Clear Technology and customer, Crystal Clear
Technology will replace or repair any of its LCD and LCM which is found to be defective
electrically and visually when inspected in accordance with Crystal Clear Technology
acceptance standards, for a period of one year from date of shipment. Confirmation of such
date shall be based on freight documents. The warranty liability of Crystal Clear Technology
is limited to repair and/or replacement on the terms set forth above. Crystal Clear Technology
will not responsible for any subsequent or consequential events.
4.
Return LCM under Warranty
No warranty can be granted if the precautions stated above have been disregarded. The
typical examples of violations are:
i. Broken LCD glass
ii. PCB eyelet’s damaged or modified
iii. PCB conductors damaged
iv. Circuit modified in any way, including addition of components.
v. PCB tampered with by grinding, engraving or painting varnish.
vi. Soldering to, or modifying the bezel in any manner.
Module repairs will be invoiced to customer upon mutual agreement. Modules must be
returned with sufficient description of failure or defects. Any connectors or cable installed by
customer must be removed completely without damaging the PCB eyelet’s, conductors and
terminals.
CRYSTAL CLEAR TECHNOLOGY SDN. BHD.
Spec. No: G64240x05xxx00 REV 2.0
18
47500 SUBANG JAYA, SELANGOR DARUL EHSAN.
3
H
1 2
G64240x05xxx00
DRAWING NUMBER
4 5 6
CHECKED
7 8
APPROVED
08-10-2009
azhar
9
DRAWN
UNIT : MM
SCALE 1 : 1
10
1
11
1
1
SHEET
H
REV.
3
G
F
E
D
C
B
A
1 2
MATERIAL
16, JLN TP5, TMN PERINDUSTRIAN SIME UEP,
Crystal−Clear Technology
MODEL NAME NO
PART NAME
4 5 6 7 8 9 10
REMARKS
MECHANICAL
SPECIFICATION
G
F
E
D
C
B
11
A
0.48
0.53
0.48
0.53
127.15
132.6
153.6±0.3
176.0±0.5
180.0±0.5
26.43±0.3
23.7±0.3
13.2±0.5
2.0
33.87
39.0
54.0
58.0±0.3
65.0±0.5
25.4
54.0
(65.0)
5.5
13.03.0
4 - R1.5
15.6±0.3
13.0±0.3
5.5±0.3
3.5±0.5
W1
1.6
W2
GRAPHICS 64 X 240 DOTS
2 1
2122
HOLES
22 - Ø1.0
NOTE :
1. GENERAL TOLERANCE TO BE ±0.3
2. BEZEL : COATING IN BLACK
NO/EL BACKLIGHT
LED BACKLIGHT
VERSION
13.0 MAX
10.0 MAX
8.00±0.5
5.00±0.5
W1 W2
Crystal Clear Technology
16 Jalan TP5—Taman Perindustrian Sime UEP
47600 Subang Jaya—Selangor DE
Malaysia