108-1990-2 Product Specification 12Jun02 Rev A EC 0990-0882-02 NETCONNECT* SL Series Category 5e Jacks 1. SCOPE 1.1. Content This specification covers transmission performance requirements for NETCONNECT* Category 5e shielded and unshielded SL 110 jacks. These assemblies are designed for installation into various outlet plates, surface mount boxes, panels, and other similar type fittings. Jacks incorporate IDC terminals for terminating both shielded or unshielded twisted pair communications cable and will accommodate 22 - 24 AWG solid and 24 AWG stranded conductors. The maximum conductor insulation diameter is 1.27 mm [.050 in]. 1.2. Qualification When tests are performed on the subject product line, procedures specified in Figure 1 shall be used. All inspections shall be performed using the applicable inspection plan and product drawing. 1.3. Qualification Test Results Successful qualification testing on the subject product line was completed on 12Mar02. The Qualification Test Report number for this testing is 501-528-2. This documentation is on file at and available from Engineering Practices and Standards (EPS). 2. APPLICABLE DOCUMENTS The following documents form a part of this specification to the extent specified herein. Unless otherwise specified, the latest edition of the document applies. In the event of conflict between the requirements of this specification and the product drawing, the product drawing shall take precedence. In the event of conflict between the requirements of this specification and the referenced documents, this specification shall take precedence. 2.1. Tyco Electronics Documents 2.2. 108-1990:Product Specification (NETCONNECT* SL Series Jacks and Category 6 Plugs) 114-6053:Application Specification (High Performance Modular Plug Connectors) 408-8417:Instruction Sheet (SL Series 110 Connect Modular Jacks) 408-8602:Instruction Sheet (Shielded SL Series 110 Connect Modular Jacks) 501-528-2: Qualification Test Report Industrial Standards ANSI\TIA/EIA-568-B.2: ASTM D4566-98: (c)2002 Tyco Electronics Corporation Harrisburg, PA All International Rights Reserved. * Trademark | Indicates change Commercial Building Telecommunications Cabling Standard Part 2: Balanced Twisted-Pair Cabling Components Standard Test Methods for Electrical Performance Properties of Insulation and Jackets for Telecommunications Wire and Cable This controlled document is subject to change. For latest revision call AMP FAX*/Product Info number 1-800-522-6752. For Regional Customer Service, visit our website at www.tycoelectronics.com 1 of 3 LOC B 108-1990-2 3. REQUIREMENTS 3.1. Design and Construction Product shall be of the design, construction and physical dimensions specified on the applicable customer drawing. 3.2. Materials Materials used in the construction of this product shall be as specified on the applicable customer drawing. 3.3. Performance and Test Description Product is designed to meet the transmission performance requirements specified in Figure 1. Unless otherwise specified, all tests shall be performed at ambient environmental conditions. 3.4. Test Requirements and Procedures Summary Test Description Requirement Procedure Attenuation. ANSI/TIA/EIA-568-B.2, paragraph 5.4.2. ASTM D4566-98, paragraph 26. Near end crosstalk (NEXT). ANSI/TIA/EIA-568-B.2, paragraph 5.4.3. ASTM D4566-98, paragraph 24. Return loss. ANSI/TIA/EIA-568-B.2, paragraph 5.4.4. ASTM D4566-98, paragraph 45. Far end crosstalk (FEXT). ANSI/TIA/EIA-568-B.2, paragraph 5.4.5. ASTM D4566-98, paragraph 25. Propagation delay. ANSI/TIA/EIA-568-B.2, paragraph 5.4.6. ASTM D4566-98, paragraph 40. Propagation delay skew. ANSI/TIA/EIA-568-B.2, paragraph 5.4.7. ASTM D4566-98, paragraph 40. Figure 1 3.5. Product Qualification and Requalification Test Sequence Test Group (a) 1 Test Sequence (b) Attenuation 1 2 Near end crosstalk (NEXT) Return loss 3 4 Far end crosstalk (FEXT) 5 Propagation delay 6 Propagation delay skew Test or Examination NOTE (a) (b) See paragraph 4.1.A. Numbers indicate sequence in which tests are performed. Figure 2 Rev A 2 of 3 108-1990-2 4. QUALITY ASSURANCE PROVISIONS 4.1. Qualification Testing A. Specimen Selection Plugs and jacks shall be prepared in accordance with applicable Instruction Sheet and shall be selected at random from current production. Test group shall consist of 30 specimens (plug and jack). Test plugs per TIA/EIA-568-B.2 shall be used. B. Test Sequence Qualification inspection shall be verified by testing specimens as specified in Figure 2. 4.2. Requalification Testing If changes significantly affecting form, fit or function are made to the product or manufacturing process or controlling industry specification, product assurance shall coordinate requalification testing, consisting of all or part of the original testing sequence as determined by development/product, quality and reliability engineering. 4.3. Acceptance Acceptance is based on verification that the product meets the requirements of Figure 1. Failures attributed to equipment, test setup or operator deficiencies shall not disqualify the product. If product failure occurs, corrective action shall be taken and samples resubmitted for qualification. Testing to confirm corrective action is required before resubmittal. 4.4. Quality Conformance Inspection The applicable quality inspection plan shall specify the sampling acceptable quality level to be used. Dimensional and functional requirements shall be in accordance with the applicable product drawing and this specification. Rev A 3 of 3